PROVN OF BARBED WIRE FROM BSNL GATE TO MH LINE, REVENUE WORK NOS 11, 13, 14, 15, MINOR WORK NO 17 AND 18 UNDER GE(E) MATHURA

Amount

Surface dressing n exc. 15 cm deep in soft/ loose soil.

Excavating in trenches n exc 1.5 m wide and n exc 1.5 m in depth, for foundation etc. and getting out soft/loose soil complete all as specified.

M&L for PCC M-7.5 grade (Nominal mix) using 40 mm graded stone aggregate as in foundations, filling and mass concrete complete all as specified.

M&L for Brickwork with fly ash old size bricks, straight or curved on plan exc 6m mean radius, built in CM 1:6 complete all as specified.

M&L Brickwork with fly ash old size bricks, straight or curved on plan to any radius in half brick thick walls, built in CM 1:4 complete all as specified.

M&L for Brickwork with old size fly ash bricks, straight or curved on plan to any radius in thick walls, built in cement mortar 1:4 complete all as specified.

M&L rendering 15 mm thick (10mm + 5mm) plaster on fair face of brick/concrete work in CM 1:4 and surface finished even and fair by mixing integral water proofing compound in finishing coat as per manufacturers instructions complete. Note :- WPC shall be measured & paid seprately under relevant item of this BOQ.

M&L rendering 15 mm thick on other than fair faces of brick surfaces or concrete surfaces and finished surfaces even & fair in CM 1:6 all as specified

M&L rendering 10 mm thick on ceiling surfaces in CM 1:3 finished even and fair complete all as specified and as directed.

Supply only liquid water proofing compound hydroseal-W+ or eqivalent (for plaster hardening, to contol efflorescence & fungal growth) as approved by GE.

M&L for use & waste of steel form work (Rough finished flat) to side and soffits of floor or roof beams, lintels, contilevers sheves including supports etc.

M&L for use & waste of steel form work (Rough finished flat) to chajjas, chullah hoods, troughs and similar items including edges complete all as specified.

M&L for use & waste of steel form work (rough finished flat) to sides and soffit of roof slab, shelves etc n. exc 200mm thick etc complete all as specified and as directed.

M&L for form work to edges of concrete flat, roof slabs not exceeding 200 mm thick shelves etc for rough finished surfaces.

M&L for TMT bars 10 mm dia and over, cut to length bent to shape required incl cranking bending ,spirally for hooping for column ,hooking ends and binding with and including MS wire (annealed) not less than 0.9mm dia all as specified.

All as per item no 15 above but 6 mm to 8 mm dia

All as per item no 15 above but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders

M&L for RCC M-25 design mix as in chajjas etc complete.

M&L for RCC M-25 grade (Design mix) as in Beams, cantilevers, bressummers, lintels & similar RCC works all as specified and directed.

M&L for RCC M-25 grade (design mix) as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like & similar RCC works all as specified and directed.

M&L for broken stone or boulders hardcore of gauge not exceeding 63mm deposited, spread and levelled in layers not exceeding 15cm thick, watered and rammed to a true surface all as specified.

M&L for 75 mm PCC M-7.5 grade (Nominal mix) using 40 mm graded aggrigate as in sub base floor complete all as specifed.

S&F Non skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tiles exceeding o.11 sqm but not exceeding 0.18 sqm ,in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed or bedding layer in CM 1:4 all as specified and as directed.

S&F Glazed ceramic tiles in vertical surface of size 300x200x7mm/450x350x7mm/600x300x7-8mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match over and including 10mm thick rendering in CM 1:3.

S&F factory made solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube as per specification & drawings in SSR Part II of 2020.

S&F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for style and plain colour PVC sheets for top rail & bottom rail Paneling plain colour PVC sheet to be fitted in MS frame welded/sealed to the stile & rails with suitable PVC sheet beading as per specification & shown on drawing in SSR Pt II of 2020 incl tower bolt Aluminum 150mm – 2 Nos , hinges stainless steel 100 mm size – 3 Nos , handle aluminium 125 mm – 2 Nos for each shutter complete all as specified.

S&F Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staple

S&F frame work such as grills , gratings etc with ends of bars shoulderd and / or rivetted or forged into spikes framed guard bars etc confirming to FE 290 GDE E-165

M&L for 20mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills,cooking platforms and like over 20 mm thick cement mortar 1:4 including pointing in white cement 1:2 using marble dust with admixture of pigment to match with shade of granite and 100 mm stainless steel rawl plug of Hilti will be fixed @ 2 Nos per Sqm.

S&F Wash hand basin under counter with fixing accessaries set size 480x370x200 mm shape rectangular. Make :- Jaquar Cat part No CNS-WHT-701 or equivalent as approved by Engr-in-charge.

S&F Vitreous China squatting pan, ‘Orissa’ pattern, size 580 x 440 mm white, with integral foot rests including setting the trap and pan in concrete and including 10 ltr capacity PVC valveless syphonic action type low level flushing cistern and 32mm dia PVC Flush pipe complete including jointing to socket of flushing rim all as specified and as directed.

S&F Vitreous China Urinal, Half stall type, white with accessorise including CP urinal spreader for fixing with 15 mm dia pipe complete all as specified.

S&F 32 mm bore Low density polyethylene pipes (LDPE) of pressure rating 6 kgf/ cm2 fixed complete to walls for WHB/ Urinal waste pipes.

M&L for Cutting chases pinning in , making good to facing where reqd. and pointing in CM 1:3 to ends or edges of landing , steps, cills, sunshades,selfs lintels etc. and cutting chases for conceled for water tubing or conceled condute wiring etc and making good, cutting n.exc 10cm girth.complete all as specified & as directed

M&L for 1000 ltr Rotational moulded polythelene water storage tanks, TRIPLE LAYER WHITE COLOUR (cylindrical vertical with closed top) hoisted and fixed in position.

S&F 25 mm bore Gun-metal, globe or gate valves, with iron wheel head, screwed both end for iron pipe and fixed

Supplying & fixing to walls and ceiling 25 mm nominal bore, medium grade, galvanised coated steel tube conforming to IS 1239 (Part-1): 2004 including all fittings conforming to IS 1239 (Part-2): 2011 complete all as specified and as directed

Supplying & fixing to walls and ceiling 20 mm nominal bore, medium grade, galvanised coated steel tube conforming to IS 1239 (Part-1): 2004 including all fittings conforming to IS 1239 (Part-2): 2011 complete all as specified and as directed.

Supplying & fixing to walls and ceiling 15 mm nominal bore, medium grade, galvanised coated steel tube conforming to IS 1239 (Part-1): 2004 including all fittings conforming to IS 1239 (Part-2): 2011 complete all as specified and as directed.

S&F 15 mm bore fancy type Chromium plated Angle stop valve cast copper alloy screwed one ends to iron pipe or for unions and other end to PVC connection all as specified

S&F 15 mm bore fancy type Chromium plated Stop cock (concealed type) cast copper alloy screwed both ends to iron pipe.all as specified.

S&F 15 mm bore bib taps long body fancy type cast copper alloy crutch or butter fly handle screwed doen screwed for iron pipe.

S&F CP chromium plated brass pillar cock suitable for counter top. Make :- Cat Part No OPP-15001PM of Jaquar or equivalent.

S&F Brass Chromium plated shower roses 125mm size with or without swivel joints, any size, including fixing to steel pipe or union

S&F 75 mm dia PVC (SWR) floor trap with CP grating including jointing with solvent cement all as specified.

S&F 125/110 mm PVC (SWR) gully trap, setting and jointing with solvent cement all as specified.

S&F 75mm bore PVC (SWR) pipes type 'A' single socketed, in any length with rubber ring joints, laid in trenches or in floors all as specified and as directed.

S&F 75mm bore PVC (SWR) pipes type 'A' single socketed, in any length with rubber ring joints, fixed to walls all as specified and as directed.

S&F 110mm bore PVC (SWR) pipes type 'A' single socketed, in any length with rubber ring joints, laid in trenches or in floors all as specified and as directed.

S&F 110mm bore PVC (SWR) pipes type 'A' single socketed, in any length with rubber ring joints, fixed to walls all as specified and as directed.

S&F 110mm bore PVC (SWR) bends any radius all as specified and as directed.

S&F 110mm bore PVC (SWR) bends with access door any radius all as specified and as directed.

S&F 110mm bore PVC (SWR) junction single, (Single T) with access door all as specified and as directed.

S&F 75mm bore PVC (SWR) bends any radius all as specified and as directed.

S&F 75mm bore PVC (SWR) bends with access door any radius all as specified and as directed.

S&F 110mm bore PVC (SWR) vent cowl all as specified and as directed.

S&F Stack clamps out of 50mm by 5mm flat iron for fixing of 110 mm pipe to wall including all fixing arrangement.

S&F PVC connections 15mm size with PTMT nuts of length 450 mm

S&F 32 mm bore Waste fittings, brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other and fixed

S&F in repairs 32 mm dia PVC Waste pipe of 750 mm length complete including fixing to waste coupling and to the grating complete.

S&F 250 mm long Aluminum alloy anodised sliding bolt with hasp, staple (bolt type ) and fixing clips all as specified

M&L for Preparing new RCC roof surfaces and providing 10 mm thick modifyed plaster in CM 1:4 cement mixed with polymer in ratio of 1:10 (1 part of polymer and 10 parts of cement) applying priming coat of epoxy primer with resin and hardener with water dilution as per manufacturer instructions, applying two coat of solvent based polyurethane liquid membrane not less than 500 micron thick UV stable having SRI value greater that equal to 105 with consumption of 0.61 Kg/Sqm (each coat) 2 nd coat should be applied once 1st coat once it is dry Make : Asian paints /Thermax or equivalent make as approved.

Surface excavation n.exc 30 cm deep and averaging 10 cm deep and getting out soft / loose soil.

M&L for 50mm thick PCC M-10 grade (Nominal mix) using 20 mm graded stone aggregate as in plinth protection finishing the surface even and smooth without using extra cement all as specified and as directed.

M&L for preparation of newly plastered surfaces of wall and applying two coats of cement base paint including scaffolding, trestles, ladders, cradles and necessary safety measures complete all as specified and as directed.

M&L for preparing newly plastered surface of wall and applying three coats of white wash including prepration of wall complete all as specified

M&L for preparing newly plastered surface of ceiling and applying three coats of white wash including prepration of wall complete all as specified

Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete M-15 grade (Nominal mix) smooth finished, and reforming benching as required 150 mm bore of pipes.

Surface excavation n.exc 30 cm deep and averaging 15 cm deep and getting out soft / loose soil.

M&L 100 mm thick cement concrete M-7.5 grade (Nominal mix) using 40mm graded stone aggregate as in sub base.

M&L sand filling under floors incl consolidation for laying paver blocks.

M&L for Machine pressed precast concrete interlocking paver block(with grey cement and pigment) any shape and size confirming to IS 15658-2006 of 60mm thickness, M-35 Grade complete all as specified by Engr-in-charge.

Material & Labour for machine pressed precast concrete interlocking paver block of approved shape and size of 80 mm thickness, with minimum compressive strength of M-40 grade, without correction factor for chamfering, made in rubber moulds with 0.50 mm thick scratch proof lacquer coating on top surface, with white cement and pigment complete.

M&L for PCC M-10 grade (Nominal mix) using 20mm graded stone aggregate as in bed to drain pipes incl packing under and haunching against the sides of pipes after they are laid and tested for 100mm bore all as specified.

M&L for 100mm dia salt glazed stone ware drain pipes grade 'A' laid in trenches and jointed as specified.

M&L for PCC M-15 grade (Nominal mix) using 20 mm graded crushed stone aggregate) as in plinth courses, bed blocks, copings etc complete.

Returning, filling in, in-cluding spreading, levelling, watering and well ramming in layers not exc 25 cm.

Filling under floors with approved soil obtained from excavated earth including spreading and levelling in layers n exc. 25 cm thick and well ramming including watering as required.

Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5m above the starting point complete all as specified and directed

Excavating in trenches in any type of soil n exc 1.5 m wide and n exc 1.5 m deep and getting out including forming bottom to required level or slope for laying pipes on concrete bed or for manholes n exc 10 Sqm on plan and n exc 1.5m deep all as specified and shown on drawings.

Removing of surplus excavated earth to a distance exceeding exc 250m but n exc 500m and deposited where directed at a level no exc 1.5m above the starting point all as specified.

M&L, salt glazed stone ware (SWG) drain pipes 150 mm bore grade 'A' (ISI marked) laid in trench and jointed in cement mortar (1:1) complete all as specified.

M&L, PCC M-7.5 grade (Nominal mix) using 40 mm graded stone aggregate as in bedding to drain pipes including packing under and hunching against the sides of pipes after they are laid and tested complete for 150 mm bore.

M&L, cement concrete M-15 grade (Nominal mix) using 20 mm graded stone aggregate as in surface channels and drains.

Extra for forming fair finish to drains or channels 30 cm inner girth in cement concrete using extra cement, including forms, moulds, mitred/stopped ends etc.

Add or deduct from item No 84 for forming fair finished channels or drains for each 25 mm girth or part thereof over or under 30 cm. Note :- This item is only for adjustment of rate if applicable.

S&F precast reinforcement concrete M-25 (Design Mix) and set in CM 1:4 as in manhole cover slab etc complete all as specified and directed

Supply only integral water proofing compound.

S&F M.S work as in small article such as rings of 16 mm dia M.S round bar made to shape complete all as specified and directed.

Dismantling of AC corrugated or semi-corrugated sheets in roof covering including ridges, hips, valleys and flashings etc .

Dismantling timber scantlings (framed work) exc 40Sqcm in section, in any position.

Demolition of cement concrete (unreinforced) in ground floors and pavings n.exc 15cm thick, including removing rubbish off the premises complete all as directed

Demolition of brick work or stone boulder masonary built in cement mortar including all quoins arches pillars etc. but excluding ashlar facing dressed stone work and precast concrete articles.

Cutting openings, through brick walls built with cement mortar for door, window and other openings or enlarging existing openings, converting window into door openings, etc. or cutting out defective brick work for under-pinning, including providing, fixing and removing shoring, cleaning and stacking bricks, removing surplus serviceable bricks, hard-core, etc., to store and rubbish not exc. 50m

Forming jambs, etc., to openings (to foregoing item), including cutting, toothing and properly bonding into old work, also facing, jointing and pointing to match existing work, complete with CM 1:4.

Taking down cement or cement lime plaster on brick or stone walls, etc. including racking out joints, hacking for key,scrubbing down with water, etc.

Taking down chowkats or frames with shutters (without taking off shutter from the frames) not exceeding 1.5 Sqm each .

Taking down chowkats or frames with shutters (without taking off shutter from the frames ) exceeding 1.5 Sqm each but n.exc. 4 sqm each

Dismantling, floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises

M&L for Mild steel work in tubular trusses, purlins, vetical posts including special shaped washer, angle cleats, fish plates, gusset plates, base/ bearing plates, bolts and nuts etc. complete using ERW or induction butt welded tubes conforming to 1161-1979 grade st 240.

S&F MS flat iron wind ties for roof including all necessary drilling, bolting or riveting etc complete all as specified and as directed.

S&F Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as per IS 15965: 2012 in roof covering fixed with self tapping screws complete.

S&F Pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as per IS 15965: 2012 in cladding to wall, fixed with self tapping screws as specified.

Providing and fixing inter locking metal grid (snap grid for false ceiling) of size 605 mm x 605 mm in true horizontal level, hot dipped galvanized steel sections (galvanized @ 120 grams/sqm, both side inclusive) consisting of main “T” runner with suitably spaced joints to get required length and of size 24 mm X 38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross “T” of size 24 mm X 28 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main “T” at 600 mm center to center to form a grid of 1200 mm x 600 mm and secondary cross “T” of length 600 mm and size 24 mm X 28 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200 mm X 600 mm panel to form grids of 600 mm X 600 mm and wall angle of size 24 mm X 24 mm X 0.4 mm. Main “T” runners to be suspended from ceiling using GI slotted cleats of size 27 mm X 37 mm X 25 mm X 1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85 mm X 30 mm X 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications and as directed by Engineer-in-charge.

M&L for providing Gypsum Board 12mm thick in ceiling fixed with screw as per manufacturers instructions

S&F 125x60 mm Pressed steel frames made out of 1.25mm steel sheet for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., with one shop coat of red oxide primer complete, as specified, supplied and fixed all as specified and as directed.

M&L Cement concrete M-10 grade (Nominal mix) using 40 mm graded aggregate as in filling for frame etc. complete all as specified.

S&F 35 mm thick, Flush shutters, solid core construction, with block board core and plywood face panels, commercial type both face covered with decorative face veneer with lipping/frame to match on both sides complete as specified.

S&F 30mm thick, locally made glazed and skelton shutters of IInd class hard wood, open rebated and prepared to receive glass/ gauze etc edges or framing plain chamfered or rounded fitted with cut or mitred beads for securing glass etc complete all as specified.

S&F Power coated (Powder coating shall not be less than 50 microns of approved colour) aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing n. less than 0.65 Kg/Rm etc. complete all as specified

S&F Power coated (Powder coating shall not be less than 50 microns of approved colour) aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.),hinges type B-21 100mm long (2no.) suitable handle ,(01 no.) complete all as specified.

S&F 5mm thick Sheet glass, ordinary quality and glazing in square exc 0.5 sqm in each pane fixed with window shuttter complete all as specified.

S&F 4 mm thick Figured glass, pin head type and glazing in squares n exc 0.5 sq. m in each pane fixed with ventilator shuttter complete all as specified.

S&F 100mm Butt hinges, heavy weight, cold rolled mild steel.

S&F 150mm long Aluminium, anodised, barrel tower bolts of extruded section.

S&F 150mm long Aluminium handles, cast type, anodised.

S&F 250 mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed

S&F white coloured 1000 liters capacity rotational moulded polyethylene triple layer water storage tank (Cylindrical vertical with close top) hoisted and fixed in position including connections including dismantling existing old water storage tank all as specified.

S&F 20 mm dia Ball brass valve high pressure with polythene float and fly nuts complete screwed for iron pipes or brass ferrule and fixed

M&L for Cutting chases pinning in , making good to facing where reqd. and pointing in CM 1:3 to ends or edges of landing , steps, cills, sunshades,selfs lintels etc. and cutting chases for conceled for water tubing or conceled condute wiring etc and making good, cutting n.exc 10cm girth.complete all as specified & as directed

S&F 25 mm bore Gun-metal, globe or gate valves, with iron wheel head, screwed both end for iron pipe and fixed

Supplying & fixing to walls and ceiling 25 mm nominal bore, medium grade, galvanised coated steel tube conforming to IS 1239 (Part-1): 2004 including all fittings conforming to IS 1239 (Part-2): 2011 complete all as specified and as directed

M&L for Preparing new steel surface of any description over 10cm in width or girth and applying two coats of synthetic enamel pain over a coat of red oxide primer complete all as specified and as directed by the Engineer-In-Charge.

M&L for Preparation of old plastered or un plastered distempered surfaces of walls by washing, rubbing down, stopping of distempered or painted surfaces, removing nails and applying one coat of oil bound distemper on wall surfaces complete.

M&L for use & waste of steel formwork to sides of concrete foundations, footings, bases of columns for flat rough finished surface complete all as directed.

M&L for RCC M-25 (Design mix) as in foundation, footings etc. all as specified and directed.

M&L for use & waste of steel form work to sides of pillars, posts and columns for rough finished surface square/rectangular of concrete complete all as directed.

M&L for RCC M-25 grade (Design mix) as in Columns, pillars, piers, posts and struts & similar works all as specified and directed.

M&L cement concrete M-15 grade (Nominal mix) using 20mm graded stone aggregate as in roof kerbs of mud stops, bed blocks, coping, column posts, boundary pillars bed plates etc including necessary form work complete all as specified and directed.

M&L For MS work as in gates of angle or other section, pattern, ornamental type fixed to walls with pintel hinges all as per design/ pattern approved by Engr-in-Charge.

Supply and fix in repair heavy duty Galvanised. 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails straining bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. as directed Note :- Each line wire shall be measured seperately .

S&F posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165.

M&L for preparation of new plastered surfaces of wall and applying two coats of cement base paint over a coat of primer complete all as specified.

M&L for rendering 10 mm thick on fair faces of brick wall or concrete surface in cement mortar 1:4 finished even & smooth without using extra cement all as specified and directed.

M&L for preparing old plastered surfaces of walls/ceilings and applying two coats of weather proof acrylic exterior paint (100% Acrylic) with spray machine, spray hard to reached area to achieve excellent application using limited manpower and over a coat of self primer including scaffolding, trestles, ladders, cradles and necessary safety measures complete all as specified and as directed. Note :- (i) Weather proof acrylic exterior paint shall be applied machincally by latest machine such as trucare Graco or equivalent having minimum pursue of 3300 PSI.

M&L for preparation of old plastered surfaces of wall and applying one coat of cement base paint including scaffolding, trestles, ladders, cradles and necessary safety measures complete all as specified and as directed.

S&F tubular towel rail, 20mm dia D type 60 cm long between flanges.

M&L for Dark shade/double charged/ultra charged Vitrified Ceramic tiles 9 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the tiles over and including 15 mm thick screed bed in cement mortar 1:4 complete all as specified.

Demolition of Stone slabs and tiles of any description or thickness in floors, aprons etc.laid bedded and pointed in any mortar.

M&L for Rendering 10mm thick in cement mortar 1:6 on fair faces of brick work or concrete surfaces and surface finished even and smooth without using extra cement complete all as specified.

M&L for preparing newly plastered surfaces of walls and applying two coats of oil bound distemper with spray machine, spray hard to reached area to achieve excellent application using limited manpower over a coat of primer and applying wall care putty not less than 1mm thick complete all as specified and as directed. Note :- (i) Oil bound distemper shall be applied machincally by latest machine such as trucare Graco or equivalent having minimum pressure of 3300 PSI.

Excavating over areas, n. exc 1.5 meter deep and getting out in soft/loose soil complete all as specified and directed by Engr–in–charge.

Removing excavated material (Soil) exc. 1.50km but n exc. 5km and depositing where directed .

M&L for 18-20mm thick machine cut machine polished kota stone slab flooring over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing over and including 15 mm thick screed bed or bedding layer in cement mortar 1:3 complete.

S & F hot rolled medium and high tensile structural steel of grade E165 as per IS 15911: 2010 as in framed work such as grills, grating, etc., with ends of bars of shouldered and/or riveted, or forged into spikes, framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework water tanks and similar work hung as gates, including pintle hinges, stops, hand made sliding bolts etc. complete all as specified and directed by Engineer-in-charge.

Supply fabricate & fix in position Aluminium power coated (Powder coating shall not be less than 50 microns of approved colour) door shutter with frame, partly glazed with 5 mm thick tinted glass and partly panelled with 9 mm thick prelaminated particle board with both side decorative laminated including rubber bead joining cleat for fixing in position, aluminium door handle 150 mm size, aluminium barrel tower bolt 200 mm size etc all as specified below complete all as specified and directed. (a) Frame (top & side) section shall of size 101.60 x 44.75 x 2.4 mm ( Section No 14021) (b) Vertical Members of shutter Section shall be be of size 85.00 x 44.45 x 2.00 mm (Section No 19560) (c) Top Members of shutter Section shall be be of size 83.50 x 44.45 x 2.00 mm (Section No 19581) (d) Lock rail (Middle member) of shutter Section shall be be of size 150.00 x 44.45 x 3.00 mm (Section No 19596) (e) Bottom Members of shutter Section shall be be of size 150.00 x 44.45 x 3.10 mm (Section No 19584) (f) Glazing clip for securing glass of shutters shall be be of 0.80 mm thick (Section No 19370).

S&F aluminium partition wall of section as in frame /single double grove of size 63.5 x 38.1 x 2mm thick of make Jindal or equivalent including 5 mm thick tinted glass , 20 mm thick pre-laminated particle board with all necessary fittings. Vertical section has to be supported with angle of size 65 x 65 x 6 mm thick including making good of existing surface complete all as specified.

M&L powder coated (power coating shall not be less than 50 microns of approved colour) aluminium window , side hung type without sash bar to receive glass or wire gauge, aluminium section weighing 0.55 Kg/m including necessary joining cleats glazing clips, anodised aluminium snap beading screws etc. alumiium fitting such as peg stays 150 mm long (01 No), hinges type B-21 100 mm long (02 Nos) suitable handle (02 Nos) complete all as specified.

S&F 250 mm long stainless steel sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed.

Supply & fix 150 mm long stainless steel handles fabricated type anodised all as specified.

Supply & Fix 150 mm long stainless steel barrel tower bolts of extruded section and fixed.

Supply & fix 100mm long stainless steel hinge

S&F floor door stopper of brass body fixed in floor 150 mm long

Taking up or down 15mm bore steel tubing and connections, complete all as specified and as directed

S&F 16mm CPVC Pipes SDR II & special fittings (brass elbove, brass Tee male threaded brass adeptor female threaded brass adeptor etc) on walls medium grade with & including all fittings and fixed complete to walls and ceilings or laid in floors complete all as specified and directed by Engr-in-Charge.

S&F in any colour european type combination pattern WC casket type Christinna with mounted flushing cistern, PVC connection,seat cover and jointed to sewage pipe. Make:- Cera cat part No S1013119 or equivalent make given under list of makes

S&F , vitreous chinaware wash hand basin white flat back size 545x400mm excluding taps, waste, chain but including brackets waste coupling and waste pipe. Make:- Cera cat part No S2020137 or equivalent makes given under list of makes

M&L Bib cock with wall flange. Make:- Jaquar cat part No KUP-35037PM, KOHLER, GROHE approved makes as approved by GE

M&L Angular stop cock with wall flange. Make:- Jaquar cat part No KUP-35053PM , KOHLER, GROHE approved makes as approved by GE

S&F in repairs 75 mm dia Cast iron spun cast iron pipe, for soil, waste and vent in any length , laid in trenches or in floors, with cement joints, complete including taking down old U/s.

S&F in repairs 100 mm dia Cast iron spun cast iron pipe, for soil, waste and vent in any length , laid in trenches or in floors, with cement joints, complete.

S&F in repairs 100 mm dia Cast iron spun cast iron pipe, for soil, waste and vent in any length , fixed to walls, with cement joints, complete.

S&F in rpairs 75 mm dia Cast iron spun cast iron pipe, for soil, waste and vent in any length , fixed to walls, with cement joints, complete.

S&F in repair 100mm Cast iron Nahani trap, with grating including jointing to waste pipe fixed in cement concrete M-15 grade (Nominal Mix) using 20mm graded stone aggregate.

S&F in repairs CP Pillar taps fancy type 15 mm bore, cast copper alloy, with capstan heads screwed down high pressure, with or without lettered `Hot' or `Cold' with long screwed shanks & fly-nuts, screwed for iron pipe

S&F in repair Angle stop valve 15mm bore of PTMT any colour screwed for iron pipe & fixed. (min. weight 15mm-90gms)

M&L for repair 150mmx 100mm Salt-glazed stoneware gully traps, square or round mouthed, tvpe 'P' and setting and jointing in cement mortar 1:1complete all as specified.

S&F Fibre glass reinforced translucent corrugated sheeting with two corrugation side lap with coach screw & washer in roof, wall etc. of 2mm thick.

Excavation in post holes (or similar holes) each n. exc 0.5 cum, getting and , returning filling in and ramming earth or broken rubble mixed with earth around in layers not exceeding 25 cum in soft/loose soil.

Supply only chain link fencing made out of mild steel galvanized wire of any size all as specified and directed

Fixing only chain link fencing of description fixed to steel part with mild steel flat & nut bolt etc. (a) Supply only fencing will be measured and paid separately. (b) Supply & fix mild steel nut bolt line wire and flat will be measured and paid separately.

Material and labor for point wiring with 1.5 sq mm PVC insulated unsheathed single core multi-stranded copper conductor cable 1100 Volts grade (FRLS), drawn through and including 20 mm dia rigid non-metallic PVC concealed conduit (medium grade) along with 1.5 sq mm continuous PVC insulated unsheathed solid/stranded copper conductor cable for earth continuity wire, connected to earth dolly and to be terminated in modular flush metal boxes and suitable for modular fittings, concealed type, covered with modular plates for mounting modular switches, sockets, regulators etc including,cutting chasing and testing on completion complete all as specified and as directed by the Engineer-in-Charge

One light point controlled by one switch.

One Exhaust fan point controlled by one switch.

One three / five pin switch-socket outlet, 5 Amps on independent board .

One three / five pin switch-socket outlet, 5 Amps on same board.

All as per item No 173 here-in-above but for one 15 Amp 3 pin / 6 pin switch socket outlet, independent, with 2.5 sq mm single core multi-stranded copper conductor along with 2.5 sq mm continuous PVC insulated unsheathed solid copper conductor cable for earth continuity wire, all as specified .

All as per item No 173 here-in-above but for one 15 Amp 3 pin / 6 pin switch socket outlet, independent, with 4sqmm single core multi-stranded copper conductor along with 4sqmm continuous PVC insulated unsheathed solid copper conductor cable for earth continuity wire, all as specified .

S & F socket modular type 2-in-1, 5 Pin, 5 Amps 2 module .

S & F switch modular type 6 Amps one way 1 module complete all as specified

S&F switch modular type, single pole one module 15 Amps 230v

S&F socket modular type 2-in-1, 5 Pin, 6/16 Amps 2 module.

Supply and Fixing ceiling rose surface bakelite 65mm x 50mm three terminals complete all as specified. Make:- SSK/Anchor/Cona/ Havells.

Supply and Fixing Modular switch 16 Amp single pole one way,1 Module all as specified.

Supply and Fixing Modular socket 2-in-1, 5 pins 6 Amps , combined 2 Module complete all as specified.

Supply and Fixing Modular socket 2-in-1,3 and 5 pins 6 /16 Amps, combined 2 Module complete all as specified.

Supply and fix DP enclosure with a two pin and earth plug and socket complete with SP MCB of rating 20 Amps, 240 Volts complete with all conction as directed.

Supply & fixing indoor decorative ultra slim surface /Wall mounted T5 LED batten tube light complete fitting 9/10 watt LED Tube fitting (size within 600x25x40 mm) suitable for mirror light with polycarbonate channel housing & integrated electronic driver,energy efficient, 140V-270 volts,co- related colour temperature (CCT) of 6500K,>100Lm/Watt complete with all accessories internally pre-wired and including connecting up with twin core twisted flexible copper conductor cable of suitable size complete all as specified and directed by Engineer-in-Charge.

S&F LED Light fitting 1x20w 220v AC docorative box type with driver holder including LED Tubelight connecting up with three core flixible copper conductor of suitable size from ceiling rose complete all as specifed and directed

Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete.

S & F LED light fitting 1x10W bulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size.

Supply and fix Exhaust fan, steel body AC single Phase. 230V of size 300m sweep with, blades, and frame and louvers complete all as specified and directed

M&L for Submain wiring with Two runs of single core 4 sqmm for main wire and one run of single core 4 sqmm as earth wire of stranded copper conductor FRLS PVC insulated unsheathed cables conforming to IS : 694 drawn through and including concealed in wall rigid medium duty unplasticised PVC conduit conforming to IS : 9537 ( Part-3) and ISI marked not less than 20 mm dia and accessorie all conforming to IS specification complete. Note :- Two runn of 4 Sqmm single core cable, one run of 4 Sqmm earth wire & One run of PVC conduit will measured as one RM.

S & F factory made epoxy powder coated Distribution Board SPN 4 ways ( SPN MCB DB ) with metal door ( IP-43 protection ) fabricated from minimum 1.6mm thick CRCA sheet and fixed flush to wall and suitable for universal mounting and including 200 Amp copper bus bar, neutral bar, standard DIN rail, Earth bar and cable ties for cable management, top and bottom removeable gland plates with Knockouts complete all as specified

S & F Single pole and neutral (SPN) MCB 40 Amps, 240 V, 50Hz, 10KA breaking .

S & F Single pole (SP) MCB 6-32 Amps, 240 V, 50Hz,10KA breaking capacity.

Supply and fixing LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete

Supply and fix electric water heater, storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, connection piece etc.

Supply and fixing LT XLPE insulated heavy duty electric cables with aluminium condudctor, 1100 volts grade, 10 sqmm 2 core .

S&F GI pipe Light grade complete including fittings for 40 mm dia

Supply and fixing House service bracket (hook type complete with 3.0m long G.I. pipe 40mm dia Medium grade, two nos 90 degree bends. M.S hook and stay or guy complete all as specified

Material and labour for Earthing complete with GI earth plate 600mm x 600mm x 6 mm thick electrode buried directly in ground (earth pit not less then 2.25 metres deep below ground level ) with top edge of the plate not less then 1.5 metres below normal ground level connected to GI wire 4.0 mm as earth lead by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 3 of MES schedule Part-I and incl 15 mm bore light grade GI protection pipe (upto 7.5 metres beyond outer edge of earth pit) PCC M-10 grade (Nominal Mix) using 40mm graded stone aggregate in pit with 40mm thick RCC cover in reinforced cement concrete M-15 grade (Nominal Mix) using 20mm graded stone aggregate, reinforced with 8mm dia bar both way @ 150mm c/c, watering arrangement with funnel and wire mesh and 20 mm bore light grade GI watering pipe, common salt and chaarcoal filling, necessary excavation and earth work complete.

Taking down existing copper / aluminium point wiring (Light / Fan / Socket or Power Point) complete, (fittings such as switches, ceiling roses, pendants, regulators, sockets), removing materials from site and making good the disturbed surfaces of walls, floors etc as per existing specification complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC)

BHARDWAJ CONSTRUCTIONS

DIKSHA CONSTRUCTION CO

M/S SHRI RAM INFRASTRUCTURE