MISC REPAIRS TO COMPOUND WALL, FOOTPATH, GATE/ GRILL/ GRATING AND CHAIN LINK FENCING, DRAIN AND OTHER PETTY REPAIRS AT NSRY, NAVCC, CDU, MES COLONY AND VIJAY BAUGH UNDER AGE B/R-II AT GE HADDO

Amount

Demolition of reinforced cement concrete as in cover slabs etc.

M&L for pre cast cement concrete 1:2:4 type B1 (using 20mm graded stone aggregate) as in manholes cover slab set in CM (1:6) all as specified and directed.

M&L for Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed.

M&L For Excavcation in post holes (or similar holes) each n exc 0.5 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25cm, watering, and removing surplus soil to a distance n exc 50 m and making good surface

M&L PCC (1:4:8) type D2 using 40mm graded stone aggregate as in foundation filling and mass concrete complete all as specified & directed by Engineer-in-Charge.

M&L for plain cement concrete (1:2:4) type B1 (using 20mm graded stone aggregate) for post, struts (including caps) including weathering, slightly rounded or chamfered angles and throating including necessary form work all as specified and as directed.

Demolition of Precast cement concrete block walling built in CM or Cement lime Mortar complete all as specified and as directed.

Taking down cement plaster of any description on brick or stone walls etc., including raking out joints, hacking for key, scrubbing down with water etc., and removal of debris to outside MD land complete all as specified and as directed.

M&L precast cement concrete block masonry exc. 10 cm width with solid block C1 (1:3:6) (using 20 mm graded stone aggregate) and setting in cement mortar (1:6) all as specified.

M&L for rendering 10mm thick in CM (1:6) on fair faces of brick work or concrete, surfaces finished even and smooth complete all as specified and as directed.

M&L for preparation of newly plastered surfaces of walls of any description and applying two coats of cement based paint over a coat of alkali resistent primer complete all as specified and as directed.

M&L for preparation of old plastered surfaces of walls and applying one coat of cement based paint after filling the cracks/holes with filler and levelling the undulations if any with cement putty complete all as specified and as directed.

M&L for mild steel galvanised PVC coated chain link fencing, 3.15mm nominal dia of GI wire, 1.4mm thick PVC coating and average area of aperture 25 Sqcm with weight of chain link not less than 2.0 Kg/Sqm complete all as specified and as directed.

Dismantling of wrought iron or mild steel work and structural steel work of any description ot otherwise provided for complete

M&L for mild steel framed work such as grills, gratings, etc., with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars and similar work conforming to Fe-290 Grade E-165 complete all as specified and as directed.

M&L for 10mm dia mild steel round bars cut to length, bent to shape required to be used as stifferners in chain link fencing, fixed independently to angle iron posts conforming to Fe 410 (Gde-E-250) quality 'A' or Fe 290 (Gde-E-165) complete all as specified and as directed.

S&F mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, length of bolt not exceeding 5 cm and dia of neck 16 to 20 mm complete all as specified and as directed.

M&L for mild steel angle iron posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc., flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting etc., and similar work conforming to Fe-290 Gde E-165 complete all as specified and as directed.

M&L for preparation of new steel and iron surfaces of any description, not otherwise described, over 10cm in width or girth and applying two coats of synthetic enamel paint of first quality over a coat of red oxide zinc chrome primer complete all as specified and as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed.

Dismantling stone slabs and tiles of any description or thickness in floors, aprons, risers of steps, skirting, dado etc., laid bedded and pointed in any mortar complete all as specified and as directed.

M&L for glossy fiished heavy duty chequered cement concrete tiles 30cm x 30cm x 25mm thick, made of grey cement and pigments, machine pressed as in flooring, set, jointed and pointed in neat cement slurry laid over and including 20mm thick screed bed in CM (1:6) complete all as specified and as directed.

M&L for vitrified tiles light shade 10mm thick (Square/Rectangular) polished, area of each tiles not exceeding 0.36sqm as in floors etc set and jointed in neat cement slurry and pointed in white/coloured cement, laid over and including cement screed bed 15mm thick in cement mortar 1:4 complete all as specified.

Ditto all as per item No 23 above but as in skirting / dados etc. including backing coat 10mm thick in cement mortar 1:3, complete all as specified.

M&L for non-skid ceramic coloured tiles 7 to 8 mm thick (square/ rectangular), area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, as in floors etc, laid over and including 15mm thick screed bed in CM (1:4), set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and as directed.

M&L for glazed ceramic designed coloured tiles as in vertical surfaces of size 300 x 450 x 7mm thick set and jointed in neat cement slurry and pointed in coloured cement to match designed including 10mm thick backing coat in CM (1:3) complete all as specified.

M&L for machine pressed precast concrete interlocking paver block, glossy finished, any shape and size conforming to IS 15658-2006 of 80 mm thickness, M-40 grade, made of grey cement and pigments, any pattern, laid in floors, laid dry including filleting to edges in CM (1:4) complete all as specified and as directed.

M&L for sand (river sand) filling under floors or in foundations including watering and consolidation complete all as specified and as directed.

Demolition of cement concrete un-reinforced in any position and paving not exc 15cm thick above or below ground level complete all as specified and as directed.

M&L for 75mm thick PCC (1:4:8) type D2 (using 40mm graded stone aggregate) as in sub base complete all as specified and as directed.

M&L for PCC (1:1½:3) type A1 (using 20mm graded stone aggregate) as in hardstanding/ path/ pavements etc., including necessary form work, surface of concrete finished even and smooth without using extra cement complete all as specified and as directed.

M&L for forming 12mm thick expansion joints filled with pre-formed bituminous filler and top 30mm primed and sealed with sealing compound, Grade ‘A’ complete all as specified and as directed.

Finishing surface of concrete hardstanding/ path/ pavements, by brooming complete all as specified and as directed.

M&L for stainless steel hollow sections circular/ square/ rectangular in shape and any size and thickness, grade AISI-316 type (Austenitic anti-corrosive in nature) as in railings/grills/designer work including post top cap, bottom plate, cutting, bending, seamless welding and fixed in any location complete all as specified and as directed.

M&L 16 to 18mm thick granite stone (of any type ) work (table rubbed and polished) in floors, staircase tread & risers of steps, cooking platform, window cill/jambs etc laid bedded over 15mm thick CM (1:4) bedding & pointed in white/coloured cement to match coloured tiles including grinding and mirror polishing complete. (Note : Colour of granite shall be as approved by Engr-In-Charge)

Dismantling of ceiling boarding including grid of any description fixed in any position with nails

S&F for anodoised aluminium powder coated snap grid frame work for ceiling 605mm x 605mm using aluminium anodoised sections specified in SSR part-I 1991 including cutting, drilling jointing ect complrtr including 6mm dia of GI hangers wire suspenders fixed with adjustable connectors and providing 6mm thick E-boards (Classic) 605mm x 605mm size Specified by Engr-in-charge and making good

M & L for seamless false ceiling made out of 12mm thick of gypsum board fixed to the ceiling section with 25mm long self drilling and tapping screws having Philips head with under head cutter at 200mm centre to centre, including finishing the joints of face board with specially formulated joining compound and 48 mm wide fibre tape to provide seam less finish and including GI channel 0.55 mm thick with two unequal flanges of 20 to 30mm and web of 27 mm fixed to surrounding wall using nylon sleeve and screws at 450mm centre to centre/intermediate channel 0.9mm thick having two equal flanges of 215 mm each and web of 45 mm suspended from soffits at approx. 900 mm centre to centre with GI cleat and steel expansion fasteners with and including ceiling section (not exc 1.20mtr length) of 0.55 mm thick having kurled web of 50 mm and flanges of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre including 6mm thick GI hangers adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flats 40x3 mm size long and expansion hold fasteners 12.5mm dia 40mm long including thin layer of Pop with Gypsum binder, sanding the surfaces till smooth surface is obtained and finally applying two coats of acrylic emulsion over one coat primer over 3mm thick putty all as specified and as directed

Taking down chowkhats or frames with shutters without taking off shutters from frame exe 1.5 Sqm and n.exc 4 Sqm each

Taking down chowkhats or frames with shutters without taking off shutters from frame n exe 1.5 Sqm

Taking down shutters of any description exc 1.0 sqm but n.exc 2.0 sqm each

Taking down Aluminium Windows chowkhats or frames with shutters without taking off shutters from frame exe 1.5 Sqm and n.exc 4 Sqm each

Taking down Aluminium Windows and Ventilator chowkhats or frames with shutters without taking off shutters from frame n. exe 1.5 Sqm each

S&F IInd class hardwood plain solid straight chowkhats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue, pinned at joints.

S&F flush shutter 35mm thick, solid core construction, with block board core and plywood face panels, commercial type on both sides including 6mm thick wooden lipping around the edges of shutter complete all as specified and directed.

S&F 35mm thick, IInd class hard wood glazed and skeleton shutter open rebated and prepared to receive gauze, etc. ( without sash bars) edges of framing plain, chamfered or rounded fitted with cut and mitered beads for securing gauze etc size of members of shutters as specified in as Part I Ses 8 Cl 8.24 (a)

S&F Solid PVC door frame of size 50mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS Square tube, fixed in opening as per specification all as directed

S & F for Factory made solid PVC moulded with particle board core door shutter 30 mm thick panel design with 2mm thick molded PVC sheet on the front face and 2mm plain colour PVC sheet on back face, supplying and fixing in frame at site as per specification and drawing all as specified

S&F in butt hinges extruded aluminium alloy with galvanized mild steel hinge pin ,anodized of hinges 100 mm type B-21

S&F extruded aluminium alloy handle fabricated type anodized 150mm long.

S&F aluminium anodised barrel bolt of extruded section 150mm long

S&F Aluminum alloy anodized sliding door bolt 300mm long with hasp and staple (bolt type) and fixing bolts and sliding bolts of extruded such or cast aluminum alloy

M&L for 18mm thick designed rubco hut rubber wood frame shutter for cupboard, WHB counter cupboard with finish to match all adjoining surfaces including sanding and applying mixture of filler and NCD thinner (Sheenlac make), pasting chalk putty, applying sealer (Sheenlac make) and wall nut colour stainer and finally applying waxpol (Silicon make) complete all as specified and as directed.

S&F in repairs for HDF boards (fire & water proof) of 19mm thick as in CB, cabinet, shelves etc & the like with an including 02 coats of synthetic enamel spray painting glossy finish over a coat of primer incl preparation of surface complete all as specified and as directed.

M&L for Auto hinges, stainless steel grade AISI-316 type (Austenitic anti-corrosive in nature) suitable for kitchen cabinets, Cupboards, shelves etc complete all as specified and as directed.

S & F Continuous (piano) hinges, mild steel, bright finish or electrogalvanised, width of flaps 40mm (when open) complete all as specified and as directed.

S& F for anodised aluminium shutters of sliding/ openable/ fixed/ fully glazed/partially glazed/fully gauge/ Skelton door/ window and ventilator frame etc., with glass or gauge and panels with prelaminated particle board inserts, side hung type, without sash bars, using standard aluminium sections including necessary joining cleats, glazing clips, rubber packing, anodized aluminium snap beading, screws, roller for sliding windows, locking arrangement, anodized aluminium fittings such as handles, required hinging device etc. complete all as specified and directed. Note- Wire mesh and Glass pane will be measured and paid seperately as in supply only.

Supply only plain sheet glass 4.0 mm thick ordinary quality and glazing with aluminum glazing clip in aluminum window shutter not exc 0.5 Sqm in each pane.

Supply only figured glass, pin head type sheet glass 4.0 mm thick ordinary quality and glazing with aluminium glazing clip in aluminium window shutter not exc 0.5 Sqm in each pane.

S&F floor door stopper of aluminium alloy body & tongue, anodised with hard drawn spring of 140mm size fixed in floor complete all as specified and directed

Supply only Aluminium alloy wire mesh 0.45 mm nominal dia of wire average width of aperture 1.40 mm and fixed with aluminum wire staples all as specified and directed.

Supply and fix in repairs aluminium alloy wire mesh 0.45 mm nominal dia of wire average width of aperture 1.40 mm and fixed with aluminum wire staples all as specified and directed.

S&F anodised aluminium grill of approved pattern cut to required size/shape and fixed with position with aluminium bedding & frame with & including F sections, fixed to aluminium windows/ventilators complete all as specified and directed.

Dismantling of cast iron/PVC pipe any dia and any shape incl bends/branch pieces jointed in cement mortar and taking out if reqd.

S&F 110mm dia PVC (SWR) grade single socketed pipes in any length complete with rubber ring joints fixed to wall etc using synthetic rubber adhesive cement solvent complete all as specified.

S&F 110mm dia PVC (SWR) bends any radius complete all as specified.

S&F 110mm dia PVC (SWR) bends with acess door any radius complete all as specified.

S&F 110mm dia PVC (SWR) branch piece single (Single T ) equal or unequal complete all as specified.

S&F 110mm dia PVC (SWR) vent cowl complete all as specified.

S&F 75mm dia PVC (SWR) grade single socketed pipes in any length complete with rubber ring joints fixed to wall etc using synthetic rubber adhesive cement solvent complete all as specified.

S&F 75 mm dia PVC (SWR) grade bends of any radius

S&F 75 mm dia PVC (SWR) grade bends with acess door of any radius

S&F PVC (SWR) branch piece, single (SingleT ) of radius equal or unequal, 75mm dia.

S&F PVC (SWR) branch piece, single (Single Y) of radius equal or unequal, 75mm dia.

S&F PVC (SWR) vent cowl, 75mm dia.

M&L PVC (SWR) multi floor trap 75mm with grating including jointing with solvent cement complete all as specified.

S&F in repairs vitreous china ware wash hand basin white flat back of size 550x 400 mm with peatestal including brackets, 32 mm CP waste coupling, chain and plug, waste fittings, and all necessary inlet, out let connections complete.

S&F in repairs 15 mm bore pillar taps, cast copper alloy, chromium plated fancy type screwed down high pressure with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly nuts. Make :Prayag Cat No. PIS-50H

S&F in repairs for bib taps long body with flange cast copper alloy chromium plated fancy type with crutch or butter fly handle screwed down for Iron pipe or for brass fancy for CP brass fancy type 15mm dia. Make :Prayag Cat No. PIS-08H

S&F in repairs two way bib cock cast copper alloy fancy type screwed down high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for union and fixed for 15mm bore of pipe with long shank and cup. Make : Prayag Cart Part No PIS-12 H

S&F in repairs angular stop cock cast copper alloy fancy type screwed down high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for union and fixed for 15mm bore of pipe with long shank and cup. Make :Prayag Cat No. PIS-10 H

S&F in repairs vitreous china ware wash down white water closet pan (pedestal pattern with trap incl connecting to drain and flushing pipe, antisyphonage pipe incl PVC sheet cover etc complete all as specified.

M&L for vitreous China squatting pan, ‘Orissa’ pattern, size 580 x 440 mm white, with integral foot rests, P or S trap including provision of lime concrete bedding with and including PVC valveless, syphonic action type, flushing cistern 10 litre capacity, low level, white, with inlet, ball valve, float and handle including brackets, flush pipe of polyethylene of low or high density or PVC 32 mm dia, PVC connections 15mm size with PTMT nuts of length 450mm, fixed in repairs complete all as specified and as directed.

M&L for PVC valveless, syphonic action type, flushing cistern, 10 litre capacity, low level, white, with inlet, ball valve, float and handle including brackets, fixed in repairs complete all as specified and as directed.

S & F in repairs Brass chromium plated towel ring with round flange. Make Prayag Cat Part No. BA-11 or equivalent as approved by GE.

S&F in repairs Hand shower (health faucet) with 8mm dia & 1.0mtr long flexible tube with wall hook. Make Prayag Cat Part No. BEA-41 or equivalent as approved by GE.

M&L for PVC connection 15 mm size, 600mm long with PTMT nuts, fixed in repairs complete all as specified and as directed.

S&F in repairs kitchen sink with drainage board made of stainless steel 1mm thick with plugs, washers and wastes, including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm complete all as specified and as directed.

Drilling holes with drilling machine for bolts, gas pipes, etc., not exceeding 25mm dia, each hole of 10cm depth complete all as specified and as directed.

S&F in repairs 20 to 25mm dia Harrison rails (curtain rails), powder coated, anodised aluminium alloy fancy type with fixing brackets, stops, rollers etc., complete all as specified and as directed.

S&F plate rack of stainless steel of size 31"x36"x10" with steel shelves, partitions & hanging arrangements for utensils, fixed in repairs complete all as specified and as directed. MAKE: PRAYAG Cat part No. P-348 or equivalent in JAQUAR/PARRYWARE

S&F wall mixer 3-in-1 system with provision of both hand shower and over head shower composite with 115mm long bend pipe connecting legs & wall flanges with and including hand shower with 8mm dia shower tube, 450mm long shower arm and over head shower, fixed in repairs complete all as specified and as directed. MAKE: PRAYAG Cat part No. PIS-80H for wall mixer PRAYAG Cat part No. BHS-87 for hand shower PRAYAG Cat part No. BOS-90 for shower arm & over head shower

S&F for Corner glass self assembly size 300mm with chromium plated bracket guard and railing. Make: Prayag Cat No. BEA-44 or equivalent as approved by GE.

S&F in repairs concealed stop Cock with wall flange incl all fittings complete all as specified and as directed. Make : Prayag cat No-7318 or equivalent as approved by GE.

S&F in repairs CP overhead shower dia 130 mm overhead shower round with revolving joints (with body rotation) & 225mm long arm shower with rabit cleaning system and all fittings. Make - Prayag BS-76 or equivalent as approved by GE.

Taking up or down 20mm dia steel tubing connection, including cleaning for refixing or removal to store

Taking up or down 25mm dia steel tubing connection, including cleaning for refixing or removal to store

S& F for 20mm bore unplasticised PVC pipe of pressure ratings 10kgf/Sqcn including all fittings fixed complete to walls, ceiling or in floor etc

S& F for 25mm bore unplasticised PVC pipe of pressure ratings 10kgf/Sqcn including all fittings fixed complete to walls, ceiling or in floor etc

S&F for providing 25mm dia Gun Metal, globe or gate valves with iron wheel head, screwed both ends for iron pipes

Cutting chases in PCC block walls for concealed water tubing etc., and making good, cutting not exc 10 cm girth complete all as specified and as directed by engineer- in- charge.

S&F rotational moulded Polyethylene [HDPE] Water Tanks, Triple Layered, ISI Marked Cylindrical & Vertical Type 1000 Litres Capacity hoisted and fixed in position including provision of 40mm/25mm dia spouts for connecting inlet, outlet, over flow and washout pipes including taking down old tanks complete all as specified and as directed by Engineer- in - charge.

S&F for Ball valves high pressure of PTMT with epoxy coated aluminium rod & highdensity plastic ball screwed for iron pipe bore dia of 25mm (Minimum weight 455 gms) complete all as specified and as directed by Engineer- in - charge.

Dismantling plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings etc., complete all as specified and as directed.

S&F pre-painted zinc coated aluminum sheet (Galvalume) GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws including scaffolding for a height upto 12.0 metres complete all as specified and as directed. NOTES: The self tapping screw shall be of adequate length to drive into complete thickness of purlin/rafter etc., and shall be fixed using neoprene and EPDM washers. Penetration and laps in sheet shall be sealed by using proper sealant profile. HDPE fillers shall be provided wherever required to close voids between sheets, sheet & fasteners etc., as per SSR Part-I 2009 complete.

S&F pre-painted zinc coated aluminum sheet (Galvalume) GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall/valley gutters, fixed with self tapping screws including scaffolding for a height upto 12.0 metres complete all as specified and as directed. NOTES: The self tapping screw shall be of adequate length to drive into complete thickness of purlin/rafter etc., and shall be fixed using neoprene and EPDM washers. Penetration and laps in sheet shall be sealed by using proper sealant profile. HDPE fillers shall be provided wherever required to close voids between sheets, sheet & fasteners etc., as per SSR Part-I 2009 complete.

M&L for mild steel rolled sections as in main and cross beams, hip and jack rafters, purlins where connected to common rafters and running rails and guides for sliding doors, fixed with angle cleats or other connecting plates etc., conforming to Fe-410-W (Grade E-250) Quality 'A' complete all as specified and as directed.

S&F aluminum flat wind ties of any size and thickness fixed with self tapping screws for fixing roofing sheets including dismantling of old wind tie complete all as specified and as directed. NOTES: The self tapping screw shall be of adequate length to drive into complete thickness of purlin/rafter etc., and shall be fixed using neoprene and EPDM washers.

S&F for 1.25mm thick steel rolling shutters with ball bearing as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer, erected in position as indicated complete gear operated type with chain wheel and hand chain

S&F safety liver locks mild steel with 4 levers for rolling shutter all as specified and directed.

S&G collapsible steel gates, top hug, consisting of channel pickets, pivoted flat bars, top and bottom runners, brass handles etc., as specified, erected in position and securing runners with holdfasts and brackets, complete all as specified and directed.

M&L for preparation of old steel and iron surfaces of any description, not otherwise described, over 10cm in width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed.

M&L for rendering 15mm thick in two coats 5mm thick in CM (1:4) mixed with integral water proofing compound @ 3% by weight of cement over 10mm thick in CM (1:6) on fair faces of brick work or concrete, surfaces finished fair and even complete all as specified and as directed. NOTE: Water proofing compound will be measured and paid separately under relevant item of this schedule.

M&L for complete removal of existing treatment of old decorated external wall surface by scrapping, washing, cleaning etc and applying two coat of weather proof (exterior grade) acrylic emulsion paint with anti fungal property over a coat of primer of the same manufacturer as that of paint incl filling cracks, holes using wall care putty complete all as specified and as directed. (Make: Dulux Weather Shield Max or Apex Ultima from Asian Paints or Berger weather coat All guard).

M&L for cement concrete (1:2:4) type B2 (using 40mm graded stone aggregate) as in channels or drains complete all as specified and as directed.

M&L for plain cement concrete (1:3:6) type C1 (using 20mm graded stone aggregate) as in coping in lintels upto 1.5m clear span, cills, steps, seismic and other similar bands plinth courses, string courses, lacing courses, parapets and railings upto 60cm in height, copings, kneelers, apex stones, bed plates, kerbs not provided for in item 04028, water roughs and the loke including weathering, slightly rounded or chamfered angles and throating including necessary formwork as directed complete all as specified and as directed.

M&L for hardcore using broken stone or boulders of gauge exceeding 63mm and not exceeding 100 mm, deposited, spread and levelled in layers not exceeding 15cm thick, watered and rammed to a true surface complete all as specified and directed.

M&L for forming fair finished drain using extra cement

CHANDER SEKER ENTERPRISE

RELIANCE SALES AGENCY

SKV Engineering

V KARTHICK

Nirman Construction Company

M/s Ramesh Lal

M/s Saina Enterprises