Providing Fabricating and Fixing Barricading including Gate with Structural Steel Framework covered with pre coated GI profile sheet at NBCC Land measuring 21.23 Acres at Ghitorni New Delhi.

Name of Work: Providing, Fabricating & Fixing Barricading including Gate with Structural Steel Framework covered with pre-coated

GI profile sheet at NBCC’s Land measuring 21.23 Acres at Ghitorni, New Delhi.

Bill of Quantities (BoQ)

S. No. Description of Item Unit Qty. Rate Amount i/c GST Remarks

Earth work in surface excavation not exceeding 30 cm in depth

but exceeding 1.5 m in width as well as 10 sqm on plan including

getting out and disposal of excavated earth upto 50 m and lift

upto 1.5 m, as directed by Engineer-in- Charge:

Filling available excavated earth (excluding rock) in trenches,

plinth, sides of foundations etc. in layers not exceeding 20cm in

depth, consolidating each deposited layer by ramming and

watering, lead up to 50 m and for all lift.

Providing and laying in position cement concrete of specified

3 4.1 grade excluding the cost of centering and shuttering - All

work up to plinth level :

1:2:4 (1 cement : 2 coarse sand (zone-lll) derived from natural

3.1 4.1.3 sources : 4 graded stone aggregate 20 mm nominal size derived cum 20.70 7895.75 1,63,442.03

from natural sources)

1:4:8 (1 cement : 5 coarse sand (Zone-III) derived from

3.2 4.1.8 natural sources : 10 graded stone aggregate 40mm nominal cum 204.75 6826.92 13,97,811.87

size derived from natural sources).

Centering and shuttering including strutting, propping etc. and

removal of form for

4.1 5.9.1 Foundations, footings, bases of columns, etc. for mass concrete sqm 2298.00 393.01 9,03,136.98

Steel reinforcement for R.C.C. work including straightening,

5 5.22 cutting, bending, placing in position and binding all complete upto

5.1 5.22.6 Thermo-Mechanically Treated bars of grade Fe-500D or more. kg 80797.50 108.09 87,33,401.78

Providing and laying in position ready mixed or site batched

design mix cement concrete for reinforced cement concrete work;

using coarse aggregate and fine aggregate derived fromnatural

sources, Portland Pozzolana / Ordinary Portland /Portland Slag

cement, admixtures in recommended proportions as per IS: 9103

to accelerate / retard setting of concrete, to improve durability

and workability without impairing strength; including pumping of

concrete to site of laying, curing, carriage for all leads; but

excluding the cost of centering, shuttering, finishing and

reinforcement as per direction of the engineer-in-charge; for the

following grades of concrete. Note: Extra cement up to 10% of

the minimum specified cement content in design mix shall be

payable separately. In case the cement content in design mix is

more than 110% of the specified minimum cement content, the

contractor shall have discretion to either re-design the mix or

bear the cost of extra cement.

6.1 5.33.1 All works upto plinth level

Concrete of M25 grade with minimum cement content of 330 kg

Add for using extra cement in the items of design mix over and

above the specified cement content therein.

Brick work with common burnt clay F.P.S. (non modular) bricks of

class designation 7.5 in foundation and plinth in:

8.1 6.1.1 Cement mortar 1:4 (1 cement : 4 coarse sand) cum 124.20 7386.79 9,17,439.32

Steel work in built up tubular (round, square or rectangular hollow

tubes etc.) trusses etc., including cutting, hoisting, fixing in

9 10.16 position and applying a priming coat of approved steel primer,

including welding and bolted with special shaped washers etc.

9.1 10.16.1 Hot finished welded type tubes kg 201955.00 194.82 3,93,44,873.10

Providing and fixing mild steel round holding down bolts with nuts

and washer plates complete.

Structural steel work riveted, bolted or welded in built up sections,

trusses and framed work, including cutting, hoisting, fixing in

position and applying a priming coat of approved steel primer all

Digitally signed by ASHWANI

Bill of Quantities (BoQ)

S. No. Description of Item Unit Qty. Rate Amount i/c GST Remarks

Providing and fixing precoated galvanised iron profile sheets (size,

shape and pitch of corrugation as approved by Engineer-in-

Charge) of total coated thickness 0.50 mm (base metal of

minimum 0.45 mm thickness with total coating thickness of

0.05mm) with zinc coating 120 grams per sgm as per IS: 277, in

240 mpa steel grade, 5-7 microns epoxy primer on both side of

the sheet and polyester top coat 15-18 microns. Sheet should

12 12.50 have protective guard film of 25 microns minimum to avoid sqm 15000.00 740.27 1,11,04,050.00

scratches during transportation and should be supplied in single

length upto 12 metre or as desired by Engineer-in-charge. The

sheet shall be fixed using self drilling /self tapping screws of size

(5.5x 55 mm) with EPDM seal, complete upto any pitch in

horizontal/ vertical or curved surfaces, excluding the cost of

purlins, rafters and trusses and including cutting to size and shape

wherever required.

18 mm cement plaster in two coats under layer 12 mm thick

13 13.11 cement plaster 1:5 (1 cement : 5 coarse sand) finished with a top sqm 1875.00 519.69 9,74,418.75

layer 6 mm thick cement plaster 1:6 (1 cement : 6 fine sand).

Finishing walls with water proofing cement paint of required shade

14.1 13.44.1 New work (Two or more coats applied @ 3.84 kg/10 sqm) sqm 1875.00 117.15 2,19,656.25

Painting with synthetic enamel paint of approved brand and

manufacture to give an even shade :

15.1 13.61.1 Two or more coats on new work sqm 12300.00 156.24 19,21,752.00

Boring, providing and installation bored cast-in-situ reinforced

cement concrete piles of grade M-25 of specified diameter and

length below the pile cap, to carry a safe working load not less

than specified, excluding the cost of steel reinforcement but

including the cost of boring with bentonite solution and temporary

casing of appropriate length for setting out and removal of same

and the length of the pile to be embedded in the pile cap etc. by

percussion drilling using Direct mud circulation (DMC) or Bailer

and chisel technique by tripod and mechanical Winch Machine all

complete, including removal of excavated earth with all its lifts

and leads (length of pile for payment shall be measured up to

bottom of pile cap).

Total Amount i/c GST 8,48,55,354.93

Total Amount i/c GST 8,48,55,354.93

Digitally signed by ASHWANI