864/WS-37/2022-23

Amount

Dismantling timber scantlings 40 sqcm and over in section, in any position for unframed work complete all as specified and directed.

Dismantling wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets complete all as specified and directed.

Dismantling plain or corrugated steel roof sheeting of any gauge, thickness including Nainital or similar pattern roof covering complete all as specified and directed.

S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

Excavating in post holes (or similar holes) each n exc 0.5 cum, getting out in hard/dense soil, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm watering, and removing surplus soil to a distance n exc 50 m and making good surface complete all as specified and directed.

M&L for plain cement concete (1:2:4) type B1 (using 20mm graded crushed stone aggregate) as in foundation filling and mass concrete complete all as specified and directed.

S&F steel work in tubular trusses including special shaped washer etc complete using ERW or induction butt welded tubes confirming to IS-1161-1979, Grade St-240 complete all as specified and directed.

M&L for preparation of new or previously untreated steel surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide complete all as specifed and directed.

M&L for mild steel TMT bars 10mm dia and over, cut to length bent to shape required including cranking bending spirally for hooping for columns hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

S&F rolled mild steel in Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment conforming to Fe 410-W (Gde?E- 250) quality A complete all as specified and directed.

M&L for providing precast cement concrete drain cover of PCC (1:2:4) Type B1 (using 20mm graded crushed stone aggregate) complete all as specified and directed.

M&L for 100mm thick PCC (1:4:8) type D2 (using 40mm graded crushed stone aggregate) as in sub base of floors complete all as specified and directed.

M&L for 40mm thick PCC (1:2:4) type B1 (using 20mm graded crushed stone aggregate) as in floor finishes complete all as specified and directed.

Excavation in trenches, n exc 1.5 m wide and n exc 1.5m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sqm on plan and n exc 1.5 m in depth and getting out in any type of soil complete all as specified and directed.

M&L for PCC (1:4:8) type D2 (using 40 mm graded crushed stone aggregate) as in foundation filling and mas concrete complete all as specified and directed.

Use and waste of formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, roof beam, Lintel beam sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter for flat rough finished surfaces of concrete complete all as specified and directed.

M&L for Reinforced cement concrete (nominal mix) (1:2:4) type B1 (using 20 mm graded crushed stone aggregate) as in Foundations, including rafts, footings, oundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and directed.

Use and waste of formwork to sides of pillars, posts, struts, piers, columns and stanchions square / rectangular or polygonal for flat rough finished surfaces of concrete complete all as specified and directed.

M&L for Reinforced cement concrete (nominal mix) (1:2:4) type B1 (using 20 mm graded crushed stone aggregate) as in Columns, pillars, piers, posts and struts complete all as specified and directed.

Use and waste of formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, antilevers, shelves including sup-ports, overhangs, etc. also splays between floors and beams, etc. for flat rough finished surfaces of concrete complete all as specified and directed.

M&L for Reinforced cement concrete (nominal mix) (1:2:4) type B1 (using 20 mm graded crushed stone aggregate) as in beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed.

Ditto all as per serial item No. 9.00 described here-in-before but 8mm dia TMT bars as in stirrups, spacers and binders

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm thick complete all as specified and directed.

Removing excavated material (soils) n exc. 50 m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified and directed.

M&L for hardcore of broken stone or boulders of gauge n exc. 63mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and directed

M&L for 75mm thick PCC (1:2:4) type B1 (using 20mm graded crushed stone aggregate) as in floor finishes complete all as specified and directed.

M&L for Brick work with sub class 'B' old size bricks straight or curved on plan exc 6 m mean radius built in cm (1:6) complete all as specified and directed.

M&L for Rendering 10mm thick on fair faces of brick work or concrete surface in CM (1:4) finished even and smooth without using extra cement complete all as specified and directed.

M&L for Rendering 15mm thick in cement mortar 1:6 on other than fair faces of brick work or concrete surfaces finished fair and even without using extra cement complete all as specified and directed.

M&L for Preparing wall surfaces plastered or unplastered and applying two coats of distemper oil emulsion white or tinted over 1 coat of alkali resistant priming paint complete all as specified and directed

M&L for Preparing wall surfaces plastered or unplastered and applying two coats of cement base paint over a coat of alkali resistant cement based priming paint complete all as specified and directed

M&L for rolled mild steel in Roof trusses (framed), trussed purlins crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle channel, base plate or flat sections) including distance pieces, cleats etc. complete all as specified and directed

S&F 0.63 mm thick Plain, galvanised, mild steel sheeting, in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) with grade of zinc coating 275 complete all as specified and as directed.

M&L for 100 mm thick PCC (1:3:6) type C2 (using 40 mm graded crushed stone aggregate) as in plinth protection finished fair and even without using extra cement n exc 2m in length and joints filled with bitumen mastic (1:1) complete all as specified and directed.

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm thick plain colour PVC sheet reinforced with M.S Square tube, supplying & fixing in opening as per specification & drawing complete all as specified and directed.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing complete all as specified and directed.

S&F 150 mm long aluminium anodised barrel tower bolts of extruded section, complete all as specified and directed.

S&F 150 mm size aluminium handles cast type anodised complete all as specified and directed.

S&F 100 mm size Butt hinges extruded aluminium alloy with galvanised mild steel hinge pin anodised and fixed type B-21, complete all as specified and directed.

S&F 250 mm long aluminium alloy anodised sliding door bolt with hasp & staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and directed.

S&F anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and directed.

S&F Anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 No.) hinges type B-21 100mm long (2 Nos.) suitable handle (1 No.) complete all as specified complete all as specified

S&F 4 mm thick Sheet glass, ordinary quality and glazing with aluminium beading in square n exc 0.5 sqm in each pane complete all as specified and directed.

S&F anodised aluminium snap grid frame work for false ceiling of size 605mm X 605 mm complete all as specified and directed.

S&F Gypsum Board 8mm thick in ceiling fixed with screw as per manufacturers instructions and complete all as specified and directed.

S&F Rolled mild steel in Compound girders & stanchons, lattice girders, aerial masts, staging for water tanks & the like including caps, bases, splices etc. built up from two or more beam or channel sections or angles with plates, including all lattice bars, stiffeners, gusset plates, etc. GDE Fe 410-0 or Fe 250-0 complete all as specified and directed.

S&F 500 ltrs capacity Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) triple layered hoisted and fixed in position all as specified in SSR Part I and as directed.

S&F Ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed 20mm bore complete all as specified and directed.

M&L for Non-skid Ceramic coloured tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exc 0.18 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match with tile laid over and including screed bed or bedding layer 15 mm thick in CM (1:4), complete all as specified and directed.

S&F Coloured Glazed ceramic tiles in vertical surface 300x 200x 7 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match the shade of tiles over and including 15mm thick rendering in cement mortar (1:4) complete all as specified and directed.

S&F GI tubing 15mm dia medium grade with all fittings and fixed to wall, floor and ceiling etc complete all as specified and as directed.

S&F GI tubing 20mm dia medium grade with all fittings and fixed to wall, floor and ceiling etc complete all as specified and as directed.

S&F Vitreous China wash basin, white, flat back, size 550x400mm excluding taps, waste, chain and plug and porcelain stopper but including brackets including cutting for and pinning in ends of brackets or erecting stand but exclusive of fixing of supply and waste pipe, Waste coupling of PTMT (half or full threaded (Minimum weight 32mm?45gms/40mm-60 gms) complete all as specified and as directed.

S&F vitreous chine wash down water closet (pedestal pattern) white, complete including connection to drain pipe and to flushing pipe, anti-syphonage pipe etc., complete all as specified and directed

S&F chromium plated health faucet, telephonic type with CP flexible arms 1.0 mtr long, suitable to fixed to 15mm bore CP angle valves, complete all as specified and directed

S&F 15 mm bore Bib taps, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed

S&F 15mm bore angle valve, cast copper alloy, chromium plated, screwed down, high pressure, screwed both ends for iron pipe or for union, complete all as specified and directed

S&F PVC (SWR) 'P’ trap 110 mm dia complete all as specified and directed

S&F 110 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed

S&F 75 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed

S&F 75mm bore PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and directed

S&F 15mm bore Brass CP mixer for mixing hot & cold water screwed down for iron pipe and fixed complete all as specified and directed

S&F 15mm bore centre hole mixer for mixing hot & cold water, suitable for wash hand basin, cast copper alloy with dual capstan head, chromium plated, fancy type, screwed down, high pressure with lettered Hot & Cold with long screwed shanks and fly nuts, screwed for iron pipe complete all as specified and directed.

S&F Stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed 20mm complete all as specified and directed

S&F Towel Rail 600mm long of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats (Minimum weight 190gms) complete all as specified and directed

S&F PVC connections 15mm size with PTMT nuts of length 600mm complete all as specified and directed

S&F Looking mirror of specified thickness, decorative type moulding beading edge alround, mounted on 6 mm thick commercial ply or AC building board, fitted to wooden plug with CP screws, complete all as specified and directed.

S&F chromium plated toilet paper holder fixed with brass screw, complete all as specified and directed.

Cutting into existing manholes of internal dia of pipe 150 mm for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete (1:2:4) type Bl smooth finished, and reforming benching as required complete all as specified and directed.

S&F 150mm bore of pipe reinforced concrete pipe class NP 2 laid jointed complete with collers ccomplete all as specified and directed.

M&L for PCC (1:3:6) type C2 (using 40mm graded crushed stone aggregate) concrete bed to drain pipes 150 mm including packing under, and haunching against the sides of pipes after they are laid and tested complete all as specified and directed.

S&F 0.63mm thick Galvanised, corrugated mild steel sheeting with two corrugations side lap, fixed with L-type or J-type or cranked hook bolts in lieu of screws, in roofs, walls etc. with grade of zinc coating 275 complete all as specified and directed.

S&F 1.60mm thick Mild steel, plain, black sheet in wall cladding, steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. as required complete all as specified and directed.

S&F 2 mm thick Fibre glass reinforced translucent corrugated sheeting with two corrugations side lap fixed with coach screw and washer in roof, wall etc. complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

S&F Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete and conforming Fe 410 -W (Gde- E- 250) quality- A complete all as specified and directed.

S&F mild steel ball bearing 200mm / 250mm dia including anchoring rod, hasp and staple, erected in position as indicated, push pull or manual type for doors or gates complete all as specified and directed.

S&F mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, but length of bolt exc 5cm but n exc 10cm long and diameter of neck in 11-15 mm complete all as specified and directed.

Demolition of Brickwork or stone/ boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and directed.

M&L for PCC (1:3:6) type C2 (using 40 mm graded crushed stone aggregate) as in foundation filling and mas concrete complete all as specified and directed.

M&L for cement concrete (1:2:4) type B1 (using 20mm graded crushed stone aggregate) as in coping etc incl necessary formwork complete all as specified and directed.

Taking down cement or cement lime plaster, any description on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc. complete all as specified and directed.

M&L for 15mm thick (in two layer) rendering on fair faces of brick work / concrete surfaces in cement mortar (1:4) with using liquid waterproofing compound and neeru finish to plaster surface including applying one coat of each water proofing Epoxy Nitoproof 100 and Nitoproof 120 of M/S Fosroc or equivalent as specified on plastered surface complete all as specified and directed. Note : WPC shall be used 200ml/50 Kg of cement (where necessary) & will measured and paid separately.

Supply only liquid water proofing compound.

M&L for 15mm thick rendering on fair faces of brick work / concrete surfaces in cement mortar (1:4) finished top surface fair and even complete all as specified and directed.

Demolition of cement concrete (un reinforced) in ground floor & pavings n exc 15 cm thick below or above ground level complete all as specified and directed.

M&L for 100mm thick Cement concrete (1:2:4) type B1 (using 20mm graded crushed stone aggregate) as in floor finishes complete all as specified and directed.

M&L for 75mm thick cement concrete (1:3:6) type C2 (using 40 mm graded crushed stone aggregate) as in plinth protection, laid in panels of area n exc 2.00 sqm with 6mm wide joints filled with mastic complete all as specified and as directed.

M&L for preparation of old steel surfaces of any description, over 10cm in width or girth, not otherwise described and applying one coat of synthetic enamal paint complete all as specified and as directed.

Surface dressing n exc 15 cm deep in any type of soil complete all as specified and as directed.

M&L for Brick work with sub class 'B' old size bricks straight or curved on plan exc 6 m mean radius built in cm (1:4) complete all as specified and directed.

S&F rolled mild steel in Joist, channel, angle, or tee sections, fixed independently, without connecting plates, etc. (cut to ordinary lengths i.e. within 20mm of the length indicated) and conforming Fe 410 -W (Gde- E- 250) quality- A complete all as specified and directed.

M&L for 100 mm thick Cement concrete (1:3:6) type C2 (using 40mm graded crushed stone aggregate) as in flooring finished even and fair w/o using extra cement complete all as specified and directed.

S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in ridge, fixed with self tapping screws complete all as specified and directed.

S&F rolled mild steel in plate girder or single stanchions, built up of one beam or channel section with flange plates, caps, bases. splices, angle brackets, cleats and other connections and conforming Fe 410 -W (Gde- E- 250) quality- A complete all as specified and directed.

M&L for point wiring complete with PVC insulated and unsheathed, Flame retardant low smoke (FRLS) 1100 volt grade electric cable of 1.5 sqmm (nominal area) with multi stranded copper conductor single core in and including rigid PVC surface / concealed conduit not less than 20 mm dia clip with suitable MS terminal boxes (not less than 1.00mm thick) and painted with one coat of red oxide primer all around and two coats of black bituminous paint including earth dolly with 3 mm thick plastic laminated sheet top cover of approved colours including 1.50 sqmm green solid copper conductor as continuous earth wire with all accessories including lugs required, complete all as specified and directed for the following:-

One light/fan point controlled by one, one way switch

One 3 pin socket outlet 5 Amps on Independent board

S&F switch piano flush button type 5 Amp single pole one way (ISI marked) complete all as specified and directed.

S&F Ceiling rose three terminals polycarbonate, isolated body (ISI marked) complete all as specified and directed.

S&F die cast aluminium flood light with high power LEDs with LED lens as light source, suitable for area lighting of capacity 50 Watt LED flood light 230 Volt outdoor type wuth thermmal manfgement in multiple optics and eqipped with IP-66 protection, with impact and corrosion resistant complete all as specified and directed.

Ditto all as per serial item No. 96.00 described here-in-before but using 2.5 sqmm single core multi stranded copper conductor PVC insulated and unsheathed cable for 3/6 pin 15 Amp socket outlet controlled by one switch on independent board with and including 2.5 sqmm green solid copper conductor cable as continuous earth wire with lugs complete all as specified and directed.

S&F socket outlet 2 in 1, 3 pin 6 Amps AC 230 Volts flush type (ISI marked) complete all as specified and directed.

S&F switch piano flush button type 15 Amp single pole one way (ISI marked) complete all as specified and directed.

S&F socket outlet 2 in 1, 6 pin, 6 and 16 amp AC 230 Volts flush type (multipurpose) complete all as specified and directed.

S&F LED light fitting 1x20W, 230 V AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed.

S&F LED light fitting mirror type with high output diffuser 2 feet, 10 Watt 220 V AC decorative type with driver holder and LED lamp connecting up with three core flexible copper conductor cable of suitable size, complete all as specified and directed.

S&F LED light fitting 10 Watt 6000K LED Bulk head luminaries including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size, complete with accessories complete all as specified and directed.

S&F exhaust fan made out of sturdy engineering plastic, complete with louvers shutter, voltage 230V, 50 Hz, 1200 RPM, copper winding of sweep 250mm complete all as specified and directed.

S&F MCB DB 4 way, 230 volt, sheet metal enclosure for MCB's, with IP-43 protection, double door with 200 Amps standard bus bar of suitable size and common neutral link all enclosed in standard sheet flush mounting complete all as specified and directed.

S&F 240 V, 10KA, 'C' curve MCB of single pole and current carrying capacity 40 Amp, in the MCB DB complete with connection testing and commissioning complete all as specified and directed.

S&F 240 V, 10KA, 'C' curve MCB of single pole and current carrying capacity 6 to 32 Amps, in the MCB DB complete with connection testing and commissioning complete all as specified and directed

Supply and laying/ fixing, GI pipe medium grade 20mm dia bore fixed to ploe/wall/ceiling or laid under floors / road / pavement, complete all as specified and directed

S&F 1100 volts grade heavy duty cable PVC insulated aluminium conductor of Size 6 Sqmm 2 core, served with inner heating of PVC tape and overall PVC sheathed in service connections suspended by insulating hangers not more than 1m apart incl 4mm suspension GI wire one twin core cable flate or circular complete all as specified and directed

M&L for earthing with galvanized steel earth plate electrode of size 600 x600 x6 mm thick buried directly in ground (earth plate not less than 2.25 mtr deep below normal ground level) with top edge of plate not less than 1.5 mtr below ground level, connected to galvanized earth lead wire of 4 mm dia by means of bolts, nuts, check nuts & washers of galvanised iron protected by GI pipe 15mm bore (light grade) and watering pipe 20mm bore GI pipe (light grade) and chamber of PCC (1:4:8) type D2 (using 40mm graded crushed stone aggregate) and coping shall be in PCC (1:3:6) type C1 (using 20mm graded crushed stone aggregate). 50mm thick cover of RCC (1:2:4) type B1 (using 20mm graded crushed stone aggregate) reinforced with 8mm dia MS tor bar @ 80mm C/C both ways including excavation and earth work and removal of surplus soil complete all as shown in electrical plate No. 3 of SSR Part I 2009 with charcoal dust and salt complete and earth lead connected to earthing test point (upto main switch DBs) complete all as specified and directed

S&F wall Mounting fan sweep 400 mm pull cord oscillating type single piece AS blade 3 speed pull cord control with complete arangement of fixing on wall complete all as directed. Make : Havells/Usha/Bajaj/Khaitan

M&L for submain wiring with two single core PVC insulated flexible FRLS copper conductor cable of sze 4 sqmm and one single core PVC insulated flexible FRLS copper conductor cable green colour of size 4.0 Sqmm as earth lead in and including PVC conduit and making good the disturbed wall surfaces to match with existing specification all as required at site or directed. Note: Three runs of cable 4 Sqmm and one run of PVC conduit shall be measured as one unit.

S&F 240 V, 10KA, 'C' curve MCB of single pole and current carrying capacity 32 Amp, in the MCB DB complete with connection testing and commissioning complete all as specified and directed.

Supply and fix Storage water heater of capacity 25 ltrs, BEE five star rated with all accessories such as saftey valve, NRV etc including making all connections complete all as specified and as directed. Make : Havells Puro Plus/Vinus Lyra/ Crompton Versa

Supply and fix GI tubing medium grade of size 15mm dia with all fittings such as tees elbows nipples union socket complete laid in floors / wall /ceiling complete all as specified and as directed.

S&F 15 mm bore Bib taps, cast copper alloy chromim plated fancy type with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed

S&F PVC connection pipe 450 mm long, 15mm size fixed to Geyser with brass nuts both ends complete all as specified and directed

M&L for point wiring with two single core PVC insulated, multistranded FR copper conductor cable of size 4.0 sqmm and one single core PVC insulated, multistranded copper conductor cable of size 1.5 sqmm green colour as earth lead in and including PVC casing & caping, medium grade for one 15 Amps socket outlet independent complete all as specified and directed.

S&F Sheet metal enclosure with socket plug top and MCBs Double pole 20 Amps and neutral enclousre with a two pin and earth plug and socket complete all as specified and directed.

S&F 20mm bore gun metal gate or globe valve with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified & as directed.

S&F stop/angle valve (ISI marked), 15 mm dia fancy type, chromium plated screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or brass ferrule complete all as specified & as directed.

M&L for submain wiring with two single core FRLS PVC insulated copper conductor cable of size 6.0 sqmm and one single core PVC insulated FRLS copper conductor cable green colour of size 6.0 Sqmm as earth lead in and including medium grade PVC casaing caping/ conduit and making good the disturbed wall surfaces to match with existing specification all as required at site or as directed. Note: Three runs of cable 6 Sqmm and one run of PVC conduit shall be measured as one unit.

S&F MCB DB 8 way, 230 volt, sheet metal enclosure for MCB's, with IP-43 protection, double door with 200 Amps standard bus bar of suitable size and common neutral link all enclosed in standard sheet flush mounting complete all as specified & as directed.

M/S Tajamul Ah Buchh