Designing, Engineering, Construction and Commissioning of Effluent Treatment Plant (Capacity-7.2MLD) on turnkey basis along with its operation and maintenance for a period of 05 years at Jhingurda Area

Amount

Survey, Soil Testing & Design Engineering Cost

Detailed survey of the area as per scope of work and submission of report.

Sub-soil exploration, field & laboratory testing of samples and submission of report

Design Engineering cost for GA and detailed engineering design and drawings of all civil and structural works included in the system and scope of work

Civil and structural work and Quantity and price break-up of all required Developmental work and infra-structure including the following

Collection Sump - 20.0 m x 30 m x 3.5 m

Inlet Chamber - 1.6 mx 1.6 m x 2.0m

Inlet Channel - 4 mx 1 m x 1.1m

Flash Mixer Chamber - 2 m dia x 2.5 m height

Clari-flocculator: Outer Clarifier Tank (18 m dia x 3.5 height) & flocculation tank (8 m dia x4.0 m height) with inlet & outlet launder (0.4m x 0.4m x 24m, each)

Clarified Water Tank - 12.5 m dia x 3m height

Treated Water Sump - 16.5 m dia x 3.5 m height

Sludge Holding Tank - 5.4 mx 5.4 m x 2.5 m & Sludge Drying Bed

COATED SPIRAL HDPE PP Alum Dosing Tank - 0.5 m dia x 1.5 m height

COATED SPIRAL HDPE PP Poly Dosing Tank - 0.5 m dia x 1.5 m height

COATED SPIRAL HDPE PP Lime Dosing Tank - 0.5 m dia x 1.5 m height

Reservoir at Workshop - 6.9 m dia x 4.5 m height

Sludge Dewatering System with storage space (5m x 7.2m x 3.3m) & Raised Platform (5m x 5m x 2.15m)

Chemical Storage Area - 40 Sq.M x 3.3 m height

Pump house with gaurd room & toilet - 7 m x 5m x 3.3 m (ht.)

Lab Room cum Office & Toilet - 4 m x 3 m x 3.3 m (ht.)

Oil Skimmer for workshop - 3 m x 1 m x 2 m

Inlet & Outlet Chamber for O & G workshop - 1x 1 m x 2 m

HDPE Pipe for untreated effluent gravity discharge from workshop to proposed ETP with excavation - 200 mm dia

Workshop Effluent Holding Tank 3.5m x 3.5m x3m

Site Development

Arboriculture and landscaping

Road 3.75 m wide

Drains (avg size 300mm x 450mm)

Pavement inside ETP premises

Boundary Wall (Total 2.5 m ht.: Brick Height 2 m & remaining concertina fencing ) with gate

MECHANICAL ITEM all complete including the following

Part A : Pumps, motors, pipes, fittings etc

Raw Water Transfer Pumps, P1 to P5 for pumping from Collection Sump to inlet chamber

Filter Feed Pumps,P6 to P9 for pumping from clarified water sump to pressurized sand filters

Treated Water Transfer Pumps ,P10 to P15

Workshop Effluent Transfer Pumps,P17 & P18

Alum Dosing Pumps D1,D2

Poly Dosing Pumps D3,D4

Lime Dosing Pumps D5,D6

Sludge Transfer Pumps P15,P16

Ultrasonic Flow Meter with online flow display and totalizer

Sluice Valve

HDPE pipe of 250 mm dia., 16 Kg/cm2

HDPE pipe of 150 mm dia., 16 Kg/cm2

HDPE pipe of 80 mm dia., 10 Kg/cm2

Plant Piping & Fittings

Part B : Process Equipments & Instruments

Oil & Grease Skimmer

Flash Mixer MechanismI Casting)

Dosing Tank Mixing Arrangement

Clariflocculator Mechanism

Pressure Sand Filter

Activated Carbon Filter

Sludge Dewatering System

REAL TIME CONTINUOUS ETP EFFLUENT MONITORING SYSTEMS

ELECTRICAL ITEM all complete including the following

Supply, fitting, fixing, commissioning and testing of 500 kVA , 6.6kV/0.433 kV Sealed ,Deta/Star, vector group DYn11, outdoor, Oil Cooled Type ONAN off circuit Star Rating Transformer with copper wound Transformer and civil foundation work along with required size & length of MS channels as per the norms 500 kVA outdoor transformer with all accessories as per IS- 1180 of 2014, air filled cable box suitable for 6.6kV 1 run , 3C 120sqmm XLPE Al. armoured cable for 1.1kV, 2 Run, 3.5Cx300sqmm XLPE Al. armoured cable as required. Apart- from the above standard fittings followings items should be included:- Capacity- 500 kVA Installation - outdoor No. of phase-Three Voltage 6.6kV/433V Vectro Group -DYn11 Duty- Continuous Tapping in primary-+/- 5% to -10% in 2.5 steps Type of Tap changer-OCTC Cooling - ONAN Insulation class-A Temp. rise @ 500 C. Ambient Oil by Thermo Meter :- 500 C.

Supply and Erection of 6.6 kV 400A 16kA outdoor type gang operated AB switch tripple pole , with 3 post pin insulators per phase, bimetallic connector mounted horizontal or vertical position on provided cross arm with adequate length of G.I. Pipe for operating handle erected on extended square shaft. The operating handle provided with lock & key at suitable height from ground level with necessary clamps, hardware etc.

Supply and Laying of 6.6kV XLPE cable from DP structure with heat shrinkable jointing kit cmplete with accessories including lugs suitable for cable size three core x 25 sqmm. Aluminium conductor

415 V sectionalized Motor Control Centre (MCC) comprising of 1 no of Incomer Air Circuit Breaker Manually Operated, Withdrawable with Guide Frame, Microprocessor based Trip Unit, 4 Pole (overload and short circuit protection) 800A ACB and required nos. of outgoing Feeders Outgoings: i) 6 nos. 200 A, MPCB, 4P (including spares) ii) 5 nos. 125 A, MPCB, 4P (including spares) iii) 11 nos Motor protection Circuit Breaker( MPCB)-32 A, 3P for different motors incuding spares iv)18 nos Motor protection Circuit Breaker( MPCB)-16 A, 3P for different motors incuding spares v) TPN MCB, 32A/16A for lighting circuit

415/230V, 3Ph, 50Hz, Lighting Distribution Board (LDB): Supply, installation, testing and commissioning of one Lighting distribution board (LDB) for illuminitation system in STP comprising of the following : Incoming MCB, 32A, 10kA, TPN, & Outgoing MCB, 16A each, DP, 3 nos . The panel should be fully enclosed and protected against dust, jets of water from directions and breaker should be free from any corrosion. The sheet steel under go minimum 7 tanks treatment followed by finishing powder coating of minimum 60 micron thickness duly compartmentalized having accessories mounted inside the cubical panel, earthing with 2 Nos. earth studs. The degree of protection should be IP:55

1100 V grade XLPE insulated PVC taped innersheated armoured Aluminium cable of 3.5Cx 20 sqmm, 3.5Cx 35 Sq.mm ,3.5Cx 70 sqmm, 3.5Cx 120 sqmm, 3.5Cx300 sqmm, and 3Cx4 Sq.mm.(Cu). as required

650/1100 V grade PVCSWA Copper, Lighting Cable

Cable trays/cable racks, cable trenches etc.

Supplying and erection of 7.0metre height Hot-dip galvanised octagonal street light pole with following arm with top dia 70mm and bottom dia A/F 130mm, made of 3mm thick sheet along with base plate of size 220x220x12mm, shall door opening for junction box mounting and suitable size foundation bolts with templete and all complete as required.

Installation, testing & commissioning of 7.0metre height Hot-dip galvanised octagonal street light pole withtools and plates wiring of luminaires with all materials and construction of shallow foundation with M-25 grade cocrete considering safe soil bearing capacity of 10T/ mtr sq.

Supplying and fixing 150 watts LED type Street light with diacast aluminium houssing for ingress protection of IP 65 and complete with all accessories etc on pole including connection.

Indoor Illumination: Supply and fixing single wall mounted 20Watt/suitable LED batten fittings complete with electronic driver and LED tube etc as required

Suitable number of earth pits shall be provided in pump house. For double earthing of all electrical equipment. The size of the earth electrode shall not be less than 100mm dia. and 3.0 m length of heavy duty GI/GS pipe and earth strips as required and other accessories of suitable sizes.

Fire Extinguisher including CO2, Dry Powder type and Water/Sand buckets with stand

Miscellaneous items like, Level Switch with IP Protection ( IP:65), PVC conduit pipe, GI pipe, flexible conduit pipe, bends,Tee joints and other accessories of suitable sizes required for completion of work.

ERECTION, INSTALLATION AND COMMISSIONING OF PLANT AND MACHINERY

Erection,installation and commissioning of all plants and machineries

OPERATION AND MAINTENANCE

Store cost for Operation and maintenance of P&M

Cost of Operation and Maintenance for First Year (manpower for ETP plant operation & maintenance and consumables)

Cost of Operation and Maintenance (manpower for ETP plant operation & smaintenance and consumables) during DLP (Four Years) excluding first year warranty

Cost towards procurement of reagents, lab equipment, glasswares,lab furniture and daily on site testing of raw and treated effluent of ETP for COD, pH, O&G & TSS by qualified Lab chemist/diplom holder and testing of raw and treated effluents of lab (internal as well as from NABL accrediated labs and submission of report thereof)

Total impact of GST for the purpose of CTC

MECO TECHNOLOGIES PVRIVATE LIMITED

POLLUCON TECHNOLOGIES LIMITED