REPAIR TO ROOF CEILING FLOORING PLINTH PROTECTION BRICK WORK PLASTERING WOODEN/ALUMINIUM/STEEL JOINERY AND CONNECTED WORKS IN C1 AND C1A AREA UNDER GE (EAST) MATHURA

Amount

Dismantling Asbestos cement (corrugated, semicorrugated, etc.) sheets in roof coverings complete all as specified and as directed.

S&F Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as per IS 15965: 2012 in roof covering fixed with self tapping screws complete all as specified and as directed.

S&F Pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as per IS 15965: 2012 as in ridge etc, fixed with self tapping screws complete all as specified and as directed.

S&F 2mm Fibre glass reinforced translucent corrugated sheeting with two corrugations side lap fixed with J type or L type or cranked hook bolts and washer in roof, wall etc complete all as specified and as directed.

S&F 6 mm thick asbestos cement corrugated or semi-corrugated sheets in roof, walls etc fixed with L-type or J-type cranked hooks complete all as specified and as directed.

Fixing only 6 mm thick asbestos cement corrugated or semi-corrugated sheeting in roof covering with L-type or J-type hooks/cranked bolts complete all as specified and as directed. Note : Serviceable Asbestos cement sheets obtained from dismantling sheet vide serial item No 1.00 above shall be used by contractor under this item.

S&F 6 mm thick asbestos cement corrugated or semi-corrugated ridge in roof fixed with L-type or J-type or cranked hooks complete all as specified and as directed.

Dismantling wall and ceiling boards (fiber, pulp, insulation, etc) or insulation board/slabs/ blankets, any thickness, including cover fillets. Complete all as specified and as directed.

S&F Anodised aluminium snap grid frame work of grid size 605 x 605mm for false ceiling including Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified and as directed.

M&L for 4 mm thick Non asbestos fibre cement building boards fixed or laid/inserted to timber/GI/Alumiium frame work as in ceiling complete all as specified and as directed.

Dismantling timber scantlings (Framed work) 40sqcm and over in section, in any position complete all as specified and as directed.

Dismantling old unserviceable wrought iron or mild steel work of any description complete all as specified and as directed.

M&L for Mild steel work in tubular trusses, purlins, vetical posts including special shaped washer, angle cleats, fish plates, gusset plates, base/ bearing plates, bolts and nuts etc. complete using ERW or induction butt welded tubes conforming to 1161-1979 grade st 240 complete all as specified and as directed.

M&L for providing cement concrete type B0 1:2:4 (using 12.5mm graded stone aggregate) as in roof kerbs or mud stops, rounded or chamfered on edges complete all as specified and as directed.

Dismantling old tiles from RCC roof including old roof treatment of any type and thickness and pattern and preparation of RCC roof surfaces with wire brushes to remove the old treatment, foreign material loose particles etc complete all as specified and as directed.

M&L for 40 mm thick (avg) thickness cement concrete 1:2:4 type B0 (using 12.5 mm graded aggregate) as in padding on roof to achieve required slope finishing the surface even and smooth without using extra cement complete all as specified and as directed.

M&L for bitumen felt water proofing treatment using APP based polymeric membrane minimum weighting 3kg/sqm and minimum thickness 3mm reinforced with polyster non woven fabric (but not less than 150gms/sqm) laid over and including bitumen primer applied @ 0.30 Kg/sqm by forced application complete all as specified and as directed.

M&L for cutting grooves in brick wall, 75mm wide and 65mm deep and shaping horizontal face of groove with cement mortar 1:3 complete all as specified and as directed.

M&L for cement concrete tiles 25cm x 25cm x 22mm thick, with grey cement and no pigments, machine pressed, set in neat cement slurry in floor laid over and including 15 mm thick screed bed in cement mortar 1:4 and filling the joints with Tile Max premium cementitious grout material of JK Cement or its equivalent complete all as specified and as directed.

Taking down cement or cement lime plaster on brick or stone walls, etc. including raking out joints,hacking for key,scrubbing down with water, etc complete all as specified and as directed.

M&L for rendering 15 mm thick on fair face of brick work or concrete surface in cement mortar 1:4 finished even & fair complete all as specified and as directed.

Supply only liquid water Proofing Compound.

M&L for providing damp proof layer in two coats of acrylic polymer coating consisting of 1 part of acrylic polymer liquid mixed with 2 parts of cementious powder applying at the rate of 1.40 Sqm/Kg of mix per coat. Second coat should be applied after 4-6 hrs of first coat, 5 days curing is to be carried out to the surface before providing plastering complete all as specified and as directed. Note : Make of the material 'Smart Care damp block 2K' of Asian paints or equivalent from Dr Fixit, STP, CICA etc. as approved by GE

M&L for preparation of new plastered surface of walls and applying two coats of cement base paint over a coat of primer complete all as specified and as directed.

M&L for rendering 15 mm thick on other than fair faces brick work or concrete surface in cement mortar 1:6 finished even & smooth without using extra cement complete all as specified and as directed.

M&L for preparation of new plastered surface of walls and applying two coats oil bound distemper over a coat of alkali resistant primer complete all as specified and as directed.

Dismantling existing water tank exc 250 ltrs and n exc 500 ltrs capacity setting aside for cleaning and removing all scale and dirt, etc from tanks and from mouths of circulating pipes, etc. and fixing in position complete all as specified and as directed.

Dismantling water tanks exc 250 ltrs and n exc 500 ltrs capacity and removing to store or from site complete all as specified and as directed.

Supply and fix 500 liters capacity white colour triple layer, rotational moulded, polythene water storage tank (Cylindrical vertical with closed top) hoisted and fixed on roof in position, including all fitting such as connection pieces with GI tank nipple for inlet, outlet, washout and overflow etc including Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for 20 mm dia bore iron pipe complete all as specified and as directed.

Dismantling water tanks exc 500 ltrs and n exc 1000 ltrs capacity and removing to store or from site complete all as specified and as directed.

Supply and fix 1000 liters capacity white colour triple layer, rotational moulded, polythene water storage tank (Cylindrical vertical with closed top) hoisted and fixed on roof in position, including all fitting such as connection pieces with GI tank nipple for inlet, outlet, washout and overflow etc including 20 mm size Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe complete all as specified and as directed.

Taking up or down 20 mm bore steel tubing and connections including cleaning for refixing or removing from site complete all as specified and as directed.

S&F 20 mm bore GI tubing, medium grade including all fitting fixed to walls and ceiling or laid in floor complete all as specified and as directed.

S&F in repairs 110 mm bore PVC (SWR) pipes single socketed in any length with rubber ring jointed fixed to wall by providing 3 No clamps made out of 25mm x 4mm flat and including providing 2 No bends of suitable size complete all as specified and as directed.

Demolition of reinforced cement concrete as in roof, floor, chajjas and similar work (reinforement cut as required to facilitate demolition) complete all as specified and as directed.

M&L for 50mm thick sand stone slab set over supports as in chajjas of ground and first floor's over windows, doors etc and jointed in cement mortar 1:4 complete all as specified and as directed.

M&L for Mild steel Joist, channel, angle, or tee sections, fixed independently, as support of Sandstone slab for chajjas of GF & FF complete all as specified and as directed.

S&F Mild steel Framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and as directed.

M&l for preparation of new steel surfaces of any description not otherwise described, over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed.

Demolition of cement Concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified and as directed.

M&L for 100 mm thick cement concrete type-D-2, 1:4:8 (using 40mm graded stone aggregate) as in sub base complete all as specified and as directed.

M&L for 75 mm thick cement concrete 1:2:4 type B-1 (using 20mm graded stone aggregate) as in sub base, sub floor, floor and paving finished the surface even and fair without using extra cement complete all as specified and as directed.

M&L for sand filling under floors or in foundations incl watering and consolidation complete all as specified and as directed.

M&L for Machine pressed precast concrete interlocking paver block with grey cement and no pigments any shape and size confirming to IS 15658-2006 of 80mm thickness, M-40 Grade complete all as specified and as directed.

M&L for 50 mm thick cement concrete 1:3:6 type C1 (using 20 mm graded stone aggregate) as in plinth protection, finishing cement concrete surface even and fair without using extra cement complete all as specified and as directed.

M&L for Chequered cement concrete tiles with white cement and pigment 30cm x 30cm x 25mm thick rubber moulded glossey finish, set, jointed and pointed in neat cement slurry in floors laid over and including 20mm screed bedding in cement mortar 1:4 complete all as specified and as directed.

Demolition of brick work or stone boulder masonary built in cement mortar including all quoins arches pillars etc. but excluding ashlar facing dressed stone work and precast concrete articles complete all as specified and as directed.

M&L for Brick work with old size fly ash Bricks straight or curved on plan exc 6 m mean radius built in cement mortar 1:6 complete all as specified and directed.

M&L for Brick work with old size sub class 'B' brick straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4 complete all as specified and as directed.

M&L for preparation of old plastered surface of walls and applying one coat of cement base paint complete all as specified and as directed.

M&l for preparation of old steel surfaces of any description not otherwise described over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed.

Use & waste of Form work to soffits of flat suspended slabs such as roof slabs floor slab landing and similar work not exceeding 200mm thick (horizontal or sloping) for rough finished surface of concrete complete all as specified and as directed.

M&L for Reinforced cement concrete type A-1 1 : 1½ : 3 (using 20mm graded stone aggragates) as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and as directed.

M&L for TMT bars 10 mm dia and over cut to length and bent to shape required including cranking bending spirally for hooping for columns hooking end and binding with and including mild steel wire ( annealed ) not less than 0.9mm dia or securing with clips complete all as specified and as directed.

M&L for 10mm thick rendering on fair faces of brick work or concrte surface as in ceiling in cement mortar 1:3 finished the surface even and smooth without using extra cemnet complete all as specified and as directed.

M&L for preparation of new plastered surface of ceilling and applying three coats of white wash complete all as specified and as directed.

Demolition of Stone slabs and tiles of any description or thickness in floors, aprons etc laid bedded and pointed in any mortar complete all as specified and as directed.

M&L for machine cut kota stone slab as in flooring 20-25 mm thick laid over and including 15mm thick screed bed in cement mortar 1:6 and jointed with gray cement mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and as directed.

M&L resecuring or easing & adjusting without taking down door shutter of any description not exc 1 sqm each complete all as specified and as directed.

M&L resecuring or easing & adjusting without taking down door shutter of any description exc 1 sqm but not exc 2.00 sqm each complete all as specified and directed.

Taking down Chowkhats or frames with shutter without taking off shutters from the frames not exc. 1.5 sqm each complete all as specified and as directed.

Taking down Chowkhats or frames with shutter without taking off shutters from the frames exc. 1.5 sqm but n exc 4 Sqm each complete all as specified and as directed.

Taking down shutters of any description exceeding 1.0sqm and not exceeding 2.0sqm each complete all as specified and as directed.

S&F Pressed steel frames of size 105x60 mm made out of 1.25mm steel sheet for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., with one shop coat of red oxide primer complete as specified and as directed.

S&F Pressed steel frames of size 125x60 mm made out of 1.25mm steel sheet for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc.with one shop coat of red oxide primer complete as specified and as directed.

M&L for cement concrete 1:3:6 type C-1 (using 20 mm graded stone aggregate) as in bed blocks for fixing hold fasts and filling of chowkhats etc complete all as specified and as directed.

M&l for preparation of new steel surfaces of any description not otherwise described, over 10cm width or girth and applying two coats of synthetic enamel paint complete all as specified and as directed.

S&F 35 mm thick factory made glazed and skeleton shutters open rebated and prepared to receive glass, gauze, etc without sash bars edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc. sizes of members of shutters as specified in SSR Part-1 section 8 clause 8.24 (a) complete all as specified and as directed.

S&F Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.18mm and fixed with stainless steel wire staples complete all as spicified and as directed.

S&F 30 mm thick factory made flush shutters, solid core construction with block board core and plywood face panel veneer type on both side complete all as specified and as directed.

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S Square tube, supplying & fixing in opening as per specification & drawing complete all as specified and as directed.

S&F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tube for top and bottom rails. MS frame shall be coverd with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail and bottom rail of either side and as gap insert for top rail and bottom rail; panelling of plain colour PVC sheet to be fitted in the MS frame welded / sealed in the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement complete all as specified and as directed.

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube but single side prelam PVC sheet used instead of Plain colour PVC sheet & edges will be painted to match with prelam sheet, suppling & fixing in opening as per specification & drawing complete all as specified and as directed.

S&F factory made Solid PVC Moulded Door Shutter 28 to 30mm thick (stiles) with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification and drawing complete all as specified and as directed.

M&L for powder coated aluminium frame for doors, windows, ventilators ( minimum thickness of powder coating 50 micron) with one or more rebates including joining cleat for fixing etc. complete all as specified including power coating.

M&L for powder coated aluminium door shutters (thickness or powder coating shall not be less than 50 microns of approved colour) aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, lock with 2 keys, anodized aluminum snap beading screws etc. complete all as specified and as directed.

M&L for powder coated aluminium window shutters (powder coating shall not be less than 50 microns of approved colour) side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) complete all as specified and as directed.

S&F 5 mm thick sheet glass, ordinary quality and fixing with rubber beading area n exc. 0.5 square metre in each pane etc complete all as specified and as directed.

S&F 5 mm thick sheet glass, ordinary quality and glazing with rubber beading area exc. 0.5 square metre in each pane etc complete all as specified and as directed.

S&F 12 mm thick Prelaminated particle board, interior grade, prelaminated both sides with plain white coloured lamination fixed/inserted to aluminium shutter complete all as specified and as directed.

S&F aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts 250mm long of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed.

S&F But hinges 100 mm size of extruded aluminium alloy with galvanised mild steel hings pin anodized and fixed type B-21complete all as specified and as directed.

S&F aluminium anodised barrel tower bolts 200 mm long of extruded section and fixed complete all as specified and as directed.

S&F Extruded aluminium handles of size 150 mm, fabricated type anodised complete all as specified and as directed.

S&F steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay complete with glazing bars dovetailed or welded complete all as specified and as directed.

S&F steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay complete without glazing bars dovetailed or welded fixed to wall complete all as specified and as directed.

Hacking out old broken glass (any thickness, size, quality or description) from metal or wooden frame, glazed with putty or fixed with beads complete all as specified and as directed.

S&F 3 mm thick sheet glass ordinary quality and glazing with oil putty n.exc 0.50 Sqm in each pane complete all as specified and as directed

S&F 3 mm thick figured glass pin head type and glazing with oil putty n.exc 0.50 Sqm in each pane complete all as specified and as directed.

S&F in repair stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.18mm and fixed with stainless steel wire staples complete all as spicified and as directed.

S&F in repair 2nd Class hard wood plain fillets square/ rectangular or trianguar in section, sectional area exc 6 Sqcm but n.exc 13 Sqcm, clean sawn and fixed with nails complete all as specified and as directed.

S&F in repair aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts 250mm long of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed.

S&F in repair Butt hinges 100 mm size of extruded aluminium alloy with galvanised mild steel hings pin anodized and fixed type B-21complete all as specified and as directed.

S&F in repair Extruded aluminium handles of size 150 mm, fabricated type anodised complete all as specified and as directed.

S&F in repair aluminium anodised barrel tower bolts 200 mm long of extruded section and fixed complete all as specified and as directed.

S&F in repair 300 mm size mild steel rat tail rod pattern door springs ISI marked including roller & roller plate etc complete all as specified and as directed.

S&F in repair mild steel mortice lock vertical type100 mm size 4-lever with two keys complete all as specified and as directed.

Taking down aluminium shutters and dismantiling stiles and rails including glass panes/particle board carefully, Refabricating and refixing in same position using all old material including neoprene replacement of required packing, cleats, screws complete all as specified and as directed.

S&F in reapirs double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed complete all as specified and as directed.

S&F in repair floor door stopper of aluminium anodised body and tengue, anodised with hard drwan steel spring overall length of cover plate 140 mm complete all as specfied and as directed.

S&F in repair Aluminium (die cast) body Door closer hydraulically regulated, designation No. 2, universal type, suitable for door shutters of 701 to 850 mm in width and of weight between 36 to 60 kg complete all as specified and as directed.

M&L for spot welding in repair n exc 2.5 cm in length thickness of metal to be welded not exc 6mm for fixing hinges/handle/bolts/helical door spring to iron surfaces etc. complete all as specified and as directed.

S&F in repair 25 mm dia stainless steel drapery rod cut to size and fixed in position including end caps, roller and brackets fixed to wall complete all as specified and as directed.

S&F in repair 18/19 mm thick block board grade Ist quality ,exterior grade commercial type fixed with screw to timber frame work complete all as specified and as directed.

S&F in repair 100 mm size aluminium anodised Hasp and staple, safety type, with mild steel hinge pin including bolt to hinge plate and fixed with screws complete all as specified and as directed.

S&F in repair aluminium anodized barrel tower bolts 75 mm long of extruded section and fixed complete all as specified and as directed.

S&F in repair Continuous (piano) hinges width of flaps 40 mm (when opened) mild steel, bright finish or electrogalvanised complete all as specified and directed.

S&F in repair Door Seal fixed to door bottom rail with screws complete all as specified and as directed.

M&L rendering 15mm thick on fair face of brick work ofr concrete in CM 1:4 by mixing liquid water proofing compound as per manufacturers instructions and finished even and fair complete all as specified and as directed. Note :- Liquid WPC shall be measured & paid seprately under relevant item of this BOQ.

S&F solid PVC wall lining and solid PVC partion consisting of 5mm thick plain coloured PVC Sheet inclusive of solvent cement and fixing at site on PVC frame as shown on drawing complete all as specified and as directed.

S&F 5mm thick PVC sheet fillet of width 35mm for wall panelling inclusive of fixing on to wall to make PVC frame as per specification complete all as specified and as directed.

Dismantling, floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

M&L for Non skid Ceramic coloured tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including 15mm thick screed bed in cement mortar 1:6 complete all as specified and directed.

M&L for Glazed ceramic coloured tiles on vertical surface 450x300x7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match laid over and including 10 mm thick backing coat of cement mortar in 1:4 complete all as specified and directed.

S&F in repair stainless steel handles 125 mm size for kitchen cabinet shutters complete all as specified and directed.

M&L for 20 mm thick Granite slab work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like laid over and including 20mm thick screed bed in cement mortar 1:4 and pointing in white cement (1:2 )using marble dust with admixture of pigment to match with shade of granite, including rounded/half rounded edge and providing hole for gas pipe in pre-cast slab as well as in granite slab of cooking platform complete all as specified and as directed.

M&L for 50 mm thick sand stone slabs in sun-shades, chajjas, shelves, cills, landings, cover stones, templates, etc. n exc. 2m in length, punched dressed on face and along exposed edges, self faced on other side and set and pointed in lime mortar 1:2 or cement mortar 1:4 complete all as specified and directed.

Taking down steel rolling shutter and repair to shutter by greasing, oiling, painting etc. size of shutter n exc 15 Sqm each and fixing in the same opening complete all as specified and as directed.

M&L for preparation of new wooden surfaces of any description not otherwise described, over 10cm width or girth and applying two coats of synthetic enamel paint over and including a coat of pink primer complete all as specified and as directed.

B S ENTERPRISES

JWALA ELECTRIC CONTRACTORS

Ms Kamal Kant Agarwal

KASHI NATH BANWARI LAL

M/s Aditya Enterprises

M/S MAMTA CONSTRUCTIONS

M/s Hoti Lal Contractor