Construction of Tribal guest house at Tezpur, Sonitpur District

Amount

Providing and laying plain/reinforced cement concrete works cement with coarse sand & 20 mm down graded stone aggregate including dewatering if necessary, and curing complete but excluding cost of form work and reinforcement for reinforced cement concrete work (form work and reinforcement will be measured and paid separately.) (i) Using mixture machine. (B) In superstructure from plinth level to 1st floor level. (ii) Columns, pillars, posts, struts, suspended floor, roof, landing, shelf and support, balcony, lintel, sill band, beam, girder,bressumer, cantilever, staircase (except spiral stair case and landing) including preparing the top surface and finishing of nosing. (N) Without using admixture, plasticiser, (b) M-20 or Proportion in 1:1.5:3

Providing formwork of formwork of ordinary timber planking so as to give a rough finish including centering, shuttering, strutting and propping etc. heigth of propping and centering below supporting floor to ceiling not exiding 4.0m and removal of the same for in situ reinforced concrete and plain concrete work in: Columns, pilars, pots & Strut of quare/rectangular/polygonal in plain or any shape like Tee/L etc. Having plain vertical face.

Flat Surfaces such as soffits of suspended floors, roofs, landings, cantelever slabs, chajjas, balconies and the like.

Staircase with sloping or stepped soffits including risers and stringers but excluding Landing. (Using 38mm thick plank) Extra for each subsequent floor or part thereof above the First Floor level as mentioned in item no. 3.1.1 & 3.1.3(b).

Supplying, fitting and fixing in position reinforcement bars conforming to relevant I.S. Code for R.C.C. work/R.B. walling including straightening, cleaning, cutting and bending to proper shapes and length as per details, supplying and binding with 20G annealed black wire and placing in position with proper blocks, supports, chairs, spacers etc. complete (upto 1st floor level) (A) From primary produccer : TATA/SAIL/Jindal steel/Shyam steel/RINL ((i) TMT Corrosion resistant steel (CRS) reinforecment bar Extra over item 18.1.1(a,b,c) for each susequent floor or part thereof above 1st floor level.

200mm thick wall using Cellular Light Weight concrete block of Size 500x200x100mm conforming to IS-2185 Pt-3 or pt-4 in cement morter of proportion 1: 5 including racking out joints and curing complete as directed in structure (protruding rod is to be provided at every 3 course interval and will be measured and paid separately) (b) In Super structure above plinth level upto 1st floor level Extra over item no.4.3.3 (b) above for CC block work in each subsequent floor or part thereof above 1st floor level.

Extra over item no.4.3.3 (b) above for CC block work in each subsequent floor or part thereof above 1st floor level. Cement plastering:

15 mm thick cement plaster in single coat on single or hulf bribkwall for interior plastering upto 1st floor level including arises, internal rounded angles, not exeeding 80 mm girth and finished event and smooth including curing completed as directed. (B) On fair side a) In cement mortar 1:3 Extra over item no. 6.2.1 to 6.2.5 for interior plastering abobe 1st floor level for every additional floors or part thereof including curing completed as directed. (a ) On single coat plaster

Extra over item no. 6.2.1 to 6.2.5 for interior plastering abobe 1st floor level for every additional floors or part thereof including curing completed as directed. (a ) On single coat plaster

20 mm thick cement plaster in two coats, on single or hulf brick wall for interior brick up to 1st floor leve including arisers, internal rounded angles, chamfers and / or rounded angles not exeeding 80 mm in girth and finishes even and smooth including curing completyed as directed. (A) On rough side (backing coat 15 mm and finishing coat 5mm thick) a) In cement mortar 1:3 Extra over item no. 6.2.1 to 6.2.5 for interior plastering abobe 1st floor level for every additional floors or part thereof including curing completed as directed. (a ) On single coat plaster

Extra over item no. 6.2.1 to 6.2.5 for interior plastering abobe 1st floor level for every additional floors or part thereof including curing completed as directed. (a ) On single coat plaster

Extra over item no 6.2.1 to 6.2.3 for plastering on celling and soffits of stairs up to 1st floor level (instead of plastering on walls) including curing complete as directed.(167.05+21.78)=188.8

Extra over item no 6.2.1 to 6.2.3 for plastering on celling and soffits of stairs up to 1st floor level (instead of plastering on walls) including curing complete as directed.

Cement plaster skirting with cement mortar in prop. 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement including rounding of junctions with floor.

Providing VITRIFIED floor tiles of approved quality of specified size, shape and thickness not less than 18mm on floors, skirtings, risers and treads of steps over 15 mm thick base of cement mortar in prop. 1:3 (1 cement : 3 coarse sand ) including cutting where necessary finished with flush pointing with Fix-A-Tile (Choksey/Sika/Pedelite/Rouf) / white cement slurry mixed with approved pigment to match shade of tiles, mixed with approved pigment to match the shade of the tiles, complete at all levels as specified and directed. (Coloured pigment should be in conformity with colour of tiles and as approved and directed by the Department) b) Executive range Somany/ Orient/Nitco /Varmora/VITA/ Marbito/ Make i) Of size 800mmx800mm and above

Providing Antiskid tiles of approved quality size, shape not less than 8mm on floor, skirting over a cement mortar bed 15mm thick of 1:3 (1 cement : 3 coarse sand) approved make fix with Fix-A Tile (Choksey/Sika/Pedelite/Rouf) white cement complete at all leve as specificated and directed. (B) Vitrified ii)Executive range-1 (Sizes 600 mm x 300mm and above) a) Nitco made (Oak Wood)

Providing polished granite slab of approved quality, size, shape and thickness not less than 18 mm on floors, skirtings, treads and risers of steps over cement mortar bed 15 mm thick in prop. 1:3 (1 cement : 3 coarse sand ) including cutting where necessary finished with flush pointing with Fix-A-Tile Choksey/Sika/Pedelite/Rouf) /white cement slurry mixed with approved pigment to match the shade of granite slab, complete at all levels as specified and directed. (Cement plastering to be measured and paid separately). (Coloured pigment should be in conformity with colour of slab and as approved and directed by the Department). (iii) Deluxe Quality (ii) With White cement (B) On Walls

Providing polished vitrified wall tiles of approved quality, size, shape and thickness not less than 8mm on walls and skirtings over cement mortar bed 10 mm thick in prop. 1:3 (1 cement : 3 coarse sand ) including cutting where necessary finished with flush pointing with Fix-A-Tile (Choksey/Sika/Pedelite/Rouf)/white cement slurry mixed with approved pigment to match shade of tilesc complete at all levels as specified and directed. (coloured pigment should be in conformity with colour of tiles and as approved and directed by the department). iv) Of size300mmx900mm and above

Supplying, fitting, fixing and painting where necessary (one coat primer and two coats of paint) suspended ceiling which includes G.I. perimeter channels of size 0.55mm thick (having one flange of 20mm and another flange of 30mm and a web of 27mm) along with perimeter of ceiling, screw fixed to........ ........a flush look which includes filling and finishing the tapered and square edges of the boards with jointing compound, joint paper tape and two coats of drywall topcoat suitable for Gypboard complete at all levels as specified and directed. (For light fittings, grill diffusers etc. cut out to be made with the frame of perimeter channel supported suitably and measured and paid separately as and where necessary). (Glass wool to be measured and paid separately). (C ) M/F Frame Work with Acoustic Type Fissured Gypboard (Cratone) Tiles (NRC value 0.57 with 50mm glass wool mat backing) 12.5mm thick.

Armstrong acoustical ceilng Providing & fixing Armstrong Mineral fibre Acoustical suspended ceiling system with optra FG ( board/tegular) edge tiles with armstrong XL 24mm exposed grid (600x600x15)mm

Supplying, fitting and fixing SoundSoak NSS Cord (FSS Cord) wrapped acoustical wall panel system of Anutone Acoustics Ltd. Including all fixtures and fittings. d) Armstrong Wood works acoustical wall panelling

Supplying, fitting and fixing 38mm thick (finished size) wooden flooring with sal wood plank butt jointed, fitted on sal wood joist of size 100mm x 125mm spaced not more than 900mm apart fitted with 16mm dia bolt and nuts with iron clamp of 50mm x 5mm size inserting in the cement concrete floor base (floor base to be measured and paid separately) including providing 25mm thick damp proof course with water proofing compound as recommended by the manufacturer over C.C floor base including providing kiricide oiling two coats to the timber joists, underside of the flooring planks, two coats of anti-corrosive paint to the iron works, including providing ventilation gaps for the timber works of specified size (75mm x 75mm) covered with welded mesh fabrics at the face of the gap including dressing, levelling, finishing complete as specified and directed by the department at all levels (measurement shall be taken at the finished area of the works).

Providing, fitting and fixing anodised aluminuim framed glazed doors with anodised aluminium frame made of 100mm x 45mm x 2.5mm section of approved brand with door style of size 88mm x 45mm x 2.5mm, top rails 50mm x 45mm x 2mm lock rails 100mm x 45mm x 2mm and bottom rails 100mm x 45mm x 2.5mm fitted with glazing clip, special type rubber gasket complete including hydraulic floor spring, pivot, tower bolt in each leaf, aluminium door handle, lock, angles, cleat etc complete as specified and directed by the department at all levels. (i) 6mm clear glass

Providing, fitting and fixing coloured anodised aluminium partition walls of standard sections of approved brand, joints mitred and welded (manufactured to relevant I.S. specification) and providing and fitting angle cleat, rubber gasket, bolting device screws etc. at all levels. (i)Partly 6mm thick glass panes and 12mm prelaminated ply boa

Providing, fitting and fixing PVC door frame of Duroplast make DPF-5060 make suitable for DPS-3720 made from extruded PVC multichamber hollow section having dimensions of 50mmx60mm (Toletance + 1mm). Horizontal and vertical sections shall be joined by steel screws after inserting M.S. tubular rectangular galvanised L-shaped brackets of size 100mmx100mm or plastic brackets of size 75mmx75mm with metred cut at the corners. Hinge side of the frame shall be reinforced with M.S.Tubular section of size 40mmx20mm. The frame will be fixed to the column/ stiffner/ wall with the help of 3 nos 75mm long and 4mm dia steel screws and expandable fastners on each side of the door frame complete in all respects as sepcified and directed at all levels.

WINDOWS AND VENTILATORS Providing, fitting and fixing coloured anodised aluminium sliding windows and ventilators of standard sections of approved brand without horizontal glazing bars,joints mitred and welded (manufactured to relevant IS specifications) and providing and fixing handles, angle cleat, rubber gasket, roller, bolting device, locking arrangements, screws etc as required complete as specified and directed for all levels. (b)3 Track sliding window(iii)6mm coloured glass

Providing and fixing stainless steel (Grade 304) railing made of holle tubes, channel, plates etc. including welding, grinding, buffing, polishing nad making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i.c. fixing the ailing with necessary accessaries and stainless steel dash fasteners, stainless steel bolts etc. of required size on the top of the floor or the side of waist slab withsuitable arrangement as epr aproved of engineer incharge. (for payment only weight of stainless steel member is to be considerd. no extra for fixing accessoreis such as nuts, bolts, fasteners etc. will be considered).

Providing and fixing in position collapsible M.S. shutters with vertical channels 20mmx10mmx2mm braced with flat iron diagonals 20mmx5mm size with top and bottom rails of T-iron 40mmx40mmx6mm with 38mm dia steel pulleys complete with bolts and nuts, locking arrangements, stoppers, handles including applying a priming coat of red lead paint.

Providing, fitting and fixing M.S Grill of required pattern for windows / clearstory windows / opening with M.S. flats at required spacing in frame all round, squre or round M.S bar with round headed bolts and nuts or screws. (ii) Ornamental grill. (a) Fixed to brick work / P.C.C / R.C.C.

Providing and fixing 12 mm thick and 150mm wide pelmet with 25 mm dia wooden curtain rod and bracket including fixing with 15mmx3mm M.S flat 100mm long plugs complete. (a) First class Indian Teak wood/ Sisu wood

Providing welding, fitting, fixing, hoisting and fixing of Roof Trusses with purlin, bottom runner etc. fabricated out of combination of two or all of the following sections: (i) square hollow section (SHS) (II) Rectangular section(RHS) (iii) M.S. black tube conforming to relevant I.S. code 1161 - 1986 as per approved design and drawing including M.S, cleat, base plate, bolt and buts which ever reqired, including that required fixing the ceiling and one coat of red oxide Zinc chromate primer to all steel surface etc. completed as directed as per specifications.

Providing Pre Painted Galvanized Iron Sheet (PPGI) accessories (Ridges / Valley / Gutter /Flashing) at all levels including fitting and fixing self drilling, self tapping screws complete complete. TATA Blue scope/ Dyna roof / Durakolor /Wonder Roof or equivalent as directed by the Departement (iv) 0.60 mm thick

Providing Pre Painted Galvanized Iron Sheet (PPGI) accessories (Ridges / Valley / Gutter /Flashing) at all levels including fitting and fixing self drilling, self tapping screws complete complete. TATA Blue scope/ Dyna roof / Durakolor /Wonder Roof or equivalent as directed by the Departement (iv) 0.60 mm thick

Providing two coats of birla white care wall putty (water resistant white based putty or concrete / mortar wall and ceiling both internal or external) after removing all loosely adhering material from the wall surface with the help of emery stone, putty blade or wire brush and moistering the wall with sufficient quantity of clean water as specified and directed by the department. (total thickness of two coats is maximum 1.5mm) (i) Thickness = 1.5 mm thick

a) Applying one coat of cement primer of approved brand and manufacture on new wall surface after throughly brooming the surfaces free from mortar droppings and other foreign matter and including preparing the surface even and sand papered smooth.

Wall painting (two coats) with Plastic emulsion paint of approved brand and manufacture (Asian paint/ Berger paint/ ICI paint/ J & N paint/ Nerolac) on new surface to give an even shade after throughly brushing the surfaces free from mortar droppings and other foreign matter and sand papered smooth. (a).Plastic Emulsion Paint of approved brand and manufacture (Asian paint/ Berger paint/ ICI paint/ J & N paint/ Nerolac)

Extra over item no 13.4.7 above for every subsequent coat of wall painting with Plastic Emulsion Paint of approved brand and manufacture (Asian paint/ Berger paint/ ICI paint/ J & N paint/ Nerolac). (i).Plastic Emulsion Paint of approved brand and manufacture (Asian paint/ Berger paint/ ICI paint/ J & N paint/ Nerolac)

Finishing old/ new wall with water proofing weather coat smooth anti-fungal premium textured exterior finish of Sandex Matt brand of Snowcem India Ltd. of required shade after clering and clearing the surfaces etc.including scaffolding complete as directed at all levels (two coats).

Painting two coats (excluding priming coat) on new steel and other metal surface with enamel paint of approved brand and manufacture(Asian paint/ Berger paint/ ICI paint/ J & N paint/ Nerolac) to give an even shade including cleaning the surface of all dirt, dust and other foreign matter. (i) Surfaces over 100mm in width or in girth.

(a) Hiegh gloss (Assia paint / Berger paint / ICI paint/ J&K paint / Nerolac) (ii).Surfaces up to 100mm in width or girth. (a) Hiegh gloss (Assia paint / Berger paint / ICI paint/ J&K paint / Nerolac)

Raising low site around the building with approved soil obtained from outside by truck carriage including breaking clods, dressing etc. complete including paying necessary forest royelty, sales tax, land compensation, municipal gate fees, if any monopoly duty etc. (profile measurement to be taken and 12.5% deduction for shrinkage to be made from total quantity) etc. complete as directed and specified. (b) Other than Guwahati city

Earth / sand filling in plinth in layers not more than 150 mm thick including nacessary carriage, watering, ramming,etc. complite as directed and specified including payment of land compensation, forest royalty, sale taxt and other duties and txes as may be nesnecessary. (b) With hill sand obtained by truck carriage loading and unloading and carriage to the site of work.

Pre construction anti - termite treatment by applying in the entire levelled area after plinth filling and before laying floor by applying the emulsion @ 5 (five) litres per square meter of the surface to be spread with light rodding so as to ensure proper absorption by the filled up earth (supplying of necessary tools and accessories by the contractor) as per the direction of the Department complete. a) with aqueous emulsion having concentration 1:19 with chloropirophose solution (tricel or euivalent) and water, i.e. 1% solution.

Providing plinth protection with bricks laid on edge and grouted with cement mortar 1:4 and finishing with cement pointing in prop. 1:1 complete.

Providing drain with cement concrete (1:3:6) 10cm thick sides 10cm thick bed over brick flat soling including 15mm thick cement plastering in prop. 1:3 finished with a floating coat of cement slurry as directed with necessary shttering for sides and earth work in excavation of foundation trenches and refilling the sides after completion of work etc. as specified. ii). 300mm wide and average 250mm deep with bed slope 1 in 150 with initial depth of 100mm.

Grading roof for water proofing treatment with (a) Cement concrete 1:2:4 (cement: 2 coarse sand: 4 graded stone agg. 20 mm nominal size) finished with a floating coat of neat cement including rounding of junctions with floor.

Providing polished tiles of approved quality, size, shape of specified thickness on pavers over a base of 100mm compacted sand gravel including cutting where necessary finished with flush pointing with Fix-A-Tile (Choksey / Sika / Pedelite / Rouf) /white cement slurry mixed with approved pigment to match shade of tiles complete at all levels as specified and directed. (Coloured pigment should be in conformity with colour of tiles and as approved and directed by the Department). (A) SUN ROCK HIGH CTS Tiles (Pavers) (a) Silicon (Pavers) 60 mm thick

Providing scaffolding using L&T-Doka access scaffold system upto a height of 40m. supported by frames of bamboos/timber H-beams, bracings including suitable couplers, pins, tower spindles and 2nd class timber plank platforms complete as specified and directed by the department. (measurement to be taken on elevation area of the building/ structure).

Earth work in excavation for foundation trenches of walls, retaining walls, footings of columns, steps, septic tank etc., including refilling (return filling) the quantity as necessary after completion of work, breaking clods in return filling, dressing, watering and ramming etc. and removal of surplus earth with all lead and lifts as directed and specified in following classifications of soils including bailing out water where necessary as directed and specified. (A) Upto a depth of 2m below the existing ground level. (B) In hard / dense soil

Providing brick soling in foundation and under floor with stone/best quality picked Jhama brick, sand packed and laid to level and in panel after preparing the sub grade As directed including all lab our and materials and if necessary dewatering, complete. (A) Brick on flat soling.

Plain cement concrete works with coarse aggregate, of sizes 13mm to 32mm in foundation bed for footing, steps, walls, brick works etc. as directed and specified including dewatering if necessary, and curing complete(Shuttering where necesary shall be measured and paid separately) (c ) In prop. (1:5:10)

Providing and laying plain/reinforced cement concrete works cement with coarse sand & 20 mm down graded stone aggregate including dewatering if necessary, and curing complete but excluding cost of form work and reinforcement for reinforced cement concrete work (form work and reinforcement will be measured and paid separately.) (i) Using mixture machine. (A) In sub-structure upto plinth level. Foundation, footings, columns with base, tie and plinth beam, pile cap, base, slab, retaining walls, walls of septic tank, inspection pit and the like and other works not less than 100mm thick up to plinth level. (N) Without using admixture, plasticiser, (b) M-20 or Proportion in 1:1.5:3

Providing formwork of formwork of ordinary timber planking so as to give a rough finish including centering, shuttering, strutting and propping etc. heigth of propping and centering below supporting floor to ceiling not exiding 4.0m and removal of the same for in situ reinforced concrete and plain concrete work in: sides of tie beams, grade beams etc. at or below ground leve (b) Using 25mm thick plankl.

Supplying, fitting and fixing in position reinforcement bars conforming to relevant I.S. Code for R.C.C. work/R.B. walling including straightening, cleaning, cutting and bending to proper shapes and length as per details, supplying and binding with 20G annealed black wire and placing in position with proper blocks, supports, chairs, spacers etc. complete (upto 1st floor level) (b) Other ISI approved TMT reinforcement bars (SRMB/SAI/BISCON/X TECH) (for Assam type Bldg. drain work, retaining wall and boundary wall etc. Cement plaster skirting with cement mortar in prop. 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement including rounding of junctions with floor.

(a) 15 mm thick

Providing fitting and fixing Vitreous china wall hang water closet (European type W.C pan 400mm high) with seat and lead ,CP brass hinges and rubber buffers , CI/MS brackets , 40 mm dia flush band with fittings including painting of fittings and brackets, required. (Flushing Cistern to be paid separately) ii) Hindware make a) White (i) Wall mounted Closet Alexa (inclusive of seat cover and fittings) (Cat. No. 92032)

Supplying, fiting and fixing concealed cistern with all internal fittings with CI brackets including fitting and fixing standard size CP flush pipe, union clamps etc. compete as directed and specified (pipes will be measured separately) i) Parryware make Concealed Cistern (Cat.No.CIB-WHT-31801011X) with Control Plate (CP) (Cat. No. CIS-CHR-31191510X)

Providing fitting and fixing vitreous china flat back type lipped front urinal basin of with automatic flushing cistern with standard flush pipe and CP brass spreader andbrass unions, etc. complete including painting of fittings and brackets, cutting and making good the walls & floors wherever required. A) Parryware make a) White (i) AQUAFREE URINAL (Cat. No.60017)

Supplying fiting and fixing glass division plate of Jaquar make including fitting and fixing compete as directed and specified i) Parryware make. a) White (i) Partion Magnum / Large (Cat. No.C0571/07)

Providing vitreous China wash basin with CI/MS brackets, C.P brass chain with plug,PVC waste pipe including painting of fittings and brackets, cutting and making good the walls wherever required. (Pillar cock, stop cocks, waste coupling are to be paid separately) PEDESTAL BASIN (with pedestal) (C) Jaquar Make (a) White (vii) Kubix (Cat. No. KUS-WHT-0609)

Providing fitting & fixing stainless steel kitchen sink of Parryware make with CI/MS brackets, C.P. brass chain with rubber plug, PVC waste pipe etc. complete including painting the fittings ,cutting &making good the walls wherever required. (Sink cock, stop cocks, waste coupling are to be paid separately (B) Nirali (i) Glister Jumbo (Bowl Size - 610 x 460 x 254) Glossy

Providing fitting and fixing Decorative Mirror complete as directed and specified. (B) Jaquar Make (a) Double Arm Wall Mounted reversible plain / Magnifying (3X) Pivotal Mirror (Cat. No.ACN-1193N)

Providing, fitting and fixing CP soap tray / soap dish complete as directed and specified. (iv) American Standard (b) Acacia soap dish (Cat.No. VP-DY41-N)

Providing, fitting and fixing Chrome Plated towel ring complete as directed and specified. (i) Jaquar Make (i) Continental towel ring square (Cat.No. ACN-1121)

Providing, fitting and fixing Chrome Plated TOILET PAPER holder complete as directed and specified. (i) Jaquar Make (vii) Kubix toilet roll holder with cover (Cat.No.AKB-35753)

Providing, fitting and fixing Chrome Plated waste coupling complete as directed and specified. (c) Cera make (iii) Waste coupling with pop-up

Providing, fitting and fixing Chrome Plated bottle trap complete as directed and specified. (c) Cera make (ii) Bottle trap 228 mm (9”) (Cat.No.104A)

Supplying, fitting and fixing PVC pipes of 6 Kg/cm2 (Supreme/Prince) or other ISI approved including joining ,fitting and fixing wiyh clamps etc.as necessary complete at all levels including below G.L as directed and specified. a) In exposed surfaces or in trenches. (ii) 110mm dia.

(iv) 75mm dia.

Supplying fiting and fixing PVC Plain single tee of (Supreme/ Prince) or other ISI approved including joining, fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. a) In exposed surfaces or in trenches. (ii) 110mm dia.

Supplying fiting and fixing PVC single tee with door of (Supreme/Prince) or other ISI approved including joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. a) In exposed surfaces or in trenches. (ii) 110mm dia.

Supplying, fitting and fixing 87.5 degree PVC bend of (Supreme/Prince) or other ISI approved including joining ,fitting and fixing etc.as necessary complete at all levels including below G.L as directed and specified. a) In exposed surfaces or in trenches. (ii) 110mm dia.

Providing fitting and fixing PVC cowel of ISI make complete as directed and specified. (iv) 75mm dia. PVC cowel of ISI make

Providing fiting & fixing C.I. Grating to the floors complete as directed and specified. (a) 110mm dia

Construction of inspection pit inside measurement 450mm x450mm x450mm flush with 100mm diameter HCI/PVC pipes and cement concrete base in proportion 1:3:6 over flat brick soling, 12cm brick wall in cement mortar in proportion 1:4 finished with 13mm cement plaster in proportion 1:2 in side wall and floor. 450mm x450mm air tight C.I. inspection pit cover and frame complete including supplying of materials, necessary excavation of pit as directed.

Providing fitting and fixing 450mm dia. 90mm thick C.I. Man hole cover and frame of 58 Kg. weight complete as directed and specified.

Supplying fitting and fixing approved uPVC Pipes of different sizes, with all necessary 'R' brand or similar approved P.V.C. Fittings such as bend, tee, elbow, reducer, nipple, plug, long screw fitting, clamps etc. complete at all levels including below G.L. as directed and specified. f)15 mm dia SUPREME/ PRINCE / SFMC / FUSION BAND or other equvalent approved brand (High presure pipe Sch-40) (B) Concealed by chieselling or breaking brick wall/ C.C. wall/ R.C.C. wall and making good to the damaged structure.

e)20 mm dia

(A) Exposed or in trenches d) 25 mm dia

(A) Exposed or in trenches a) 50 mm dia

Supplying fitting and fixing C.P. bib cock 15mm dia of approved brand directed and specified. (G.I. & C.P pipes will be measured separately) (II) Jaquare make (b)Queen's collection /The Stealth Rangers (For VIP use. ii) C.P. 2-way bibcock double handle with flange Cat No.21017 Prior approval of Chief Engineer PWD (Bldg) must be taken before use)

Supplying fitting and fixing chrome plated (C.P.) stop-cock of approved brand and size as mentioned below as directed and specified.(G.I. & C.P pipes will be measured and paid separately) (I) Jaquare make (b) Queen's collection/ The Stealth Ranger (For VIP use. Prior approval of Chief Engineer PWD (Bldg) must be taken before use) (i) Angular stop cock with wall flange

Supplying, fitting and fixing Chrome Plated (C.P.) basin mixer complete as directed. (III) Jaquar make (For VIP use. Prior approval of Chief Engineer PWD (Bldg) must be taken before use) viii) 3-Hole basin mixer with popup waste system Cat No.7191

Supplying, fitting and fixing Chrome Plated (C.P.) wall mixer complete as directed. (V) Jaquar make iii) Wall mixer 3 in 1 system with provision for both telephonic shower and overhead shower complete with wall flange with 115mm long bend pipe Cat No.7281

Supplying, fitting and fixing Chrome Plated (C.P.) sink mixer complete as directed. (III) Jaquar make ii) Sink mixer, single hole regular spout (table mounted model) with 450mm long copper pipes and brass nuts.Cat No.7319

Supplying fitting and fixing overhead adjustable Chrome Plated (C.P.) spray shower 15mm dia. of Sona make with wall flange as directed and specified.(pipes will be measured and paid separately) (VI) Grohe make: Bau over head shower with arm 3 adjustable spreys with wall flenge Cat No- 27398000 Grohe make: Bau over head shower with arm 3 adjustable spreys with wall flenge Cat No- 27398000 (i) Shower arm light casted with wall flange

Supplying fitting and fixing Telephonic Chrome Plated (C.P.) shower of approved brand as directed and specified. (Pipes will be measured and paid separately) Lauret make (Telephonic hand shower with 1.5 m PVC pipe with hook) Supplying and fitting gun metal country pit valve (full way valve) I.S.I. Make as specified and directed.

c) 25 mm dia.

a) 50mm dia

Supplying and placing ferrocement water tanks of circular/rectengular shape over stagging with manhole cover with locking and clearing arrangement including providing pads of size as required for inlet and outlet pipes complete as directed.(Stagging should be measured and paid separately) 2000 Lt capacity water tank.

Taurus make FRP Composite Structural vessel Iron Removal Filters of 100 % rustproof vessels complete with Top & bottom Strainers, Multiport Valves, Quality filter media-e.g Treated Sand,Mno2 ,Barakar Sand Gravels & Pebbles. ISO, NSF certified. (IV) 6000 liters capacity

(D) ULTRAVIOLET (UV) Water Purifiers TAURUS make UV water Purifiers with Stainless Steel UV Chamber, Quartz Glass, Imported UV lamp, complete with in-out threaded openings ½” onwards, with 10” Pre filter for dirt, iron, turbid removal. (V)1000 liters capacity

Preparation of site for placement of the drilling rig including excavation of mud pit, circulation drain, collection chember etc. all complete as directed.

Movment of rog from the Divisional Head Quarter to the drilling site including cost of P.O.L. all complete as directed.

Transportation of all ancillary equipments, camp materials, welding set, rig accessories etc. from the Divisional Head Quarter to the work site including cost of P.O.L. all complete as directed.

a) upt ot 100 km. distance from the Divisional Head Quarter Item of Borring Using DTH Rig:. Drilling with drill bit in overburden portion of soil drilling rig using D.T.H in all kinds of rock formation including collection of sample at every 3.0 m. depth of boring or wherever there is a change of strata in sample boxes with distingushing marks upto required depth of boring along with breaking rock fracture for desired dicharge,withdrawing drilling rod and finishing the bore hole by ramming up to a required dia. up to the bottom and washing the well as per direction of the deptt. all complete including testingof yield drawdoun of SWL of the DTW in presents of engineer /vincharge with submission of all reports and lithology of the well as dircted by the deptt.

Labour charge for sinking, lowering, fitting, fixing in position of 200 mm dia. U.P.V.C pipe assembly compresing of strainer, pipes and cone in potable water bearing strata, washing the bore well etc. and supplying necessary jointing materials including carriage of materials and cleaning and priming the tube well all complete as directed. b) from 50 to 100 m. depth.

Labour charge for packing coarse sand around strainer and casing pipe including supplying and carriage of material all complete as directed and specified.

Labour charge for sinking, lowering, fitting, fixing in position of 40 mm dia. U.P.V.C pipe 40 mm dia. strainer placed with 40 mm dia. cone / plug at the bottom of the tube well washing the bore well etc. and supplying necessary jointing materials including carriage of materials and cleaning and priming the tube well all complete as directed.

Supplying of U.P.V.C. Ribbed Screen Pipe:- a) 40 mm dia.

Supplying of U.P.V.C. Pipes (IS : 12818/1992) (i) 300 mm dia.

Developing of D.T.H with air compressor, Make-Kirloskar / Cumins all completed as directed.

Supplying and packing rea gravel around the periphery of casing including screening, washing etc. all complete as directed.

Three phase Submersible motor pump set (Texmo / Crompton Greaves/ Aquatic/ CRI/ V-Guar suitable for 100 mm bore well and above. 3 HP STAGE 7 to 40 with MCB controlled Submersible motor pump set control panel.

Supplying fitting and fixing including necessary connection as approved by the deptt. of starter (Crompton Greaves / Control & switch gear / BCH / L&T Siemers make) of the following type and capacity as specified and directed by the deptt. (Crompton Greaves / Control & switch gear / BCH / L&T Siemers make). D.O.L. Starter (Crompton Greaves / Control & switch gear / BCH / L&T Siemers make) up to 15 HP, 17.4 to 24A

Earth work in excavation for foundation trenches of walls, retaining walls, footings of columns, steps, septic tank etc., including refilling (return filling) the quantity as necessary after completion of work, breaking clods in return filling, dressing, watering and ramming etc. and removal of surplus earth with all lead and lifts as directed and specified in following classifications of soils including bailing out water where necessary as directed and specified. (A) Upto a depth of 2m below the existing ground level. (b) In hard/ dense soil

Providing brick soling in foundation and under floor with stone/best quality picked Jhama brick, sand packed and laid to level and in panel after preparing the sub grade As directed including all lab our and materials and if necessary dewatering, complete. (a).Brick on flat soling.

Plain cement concrete works with coarse aggregate, of sizes 13mm to 32mm in foundation bed for footing, steps, walls, brick works etc. as directed and specified including dewatering if necessary, and curing complete(Shuttering where necesary shall be measured and paid separately) (a) In prop 1cement: 3 sand :6 coarse aggregate by volume

Providing and laying plain/reinforced cement concrete works cement with coarse sand & 20 mm down graded stone aggregate including dewatering if necessary, and curing complete but excluding cost of form work and reinforcement for reinforced cement concrete work (form work and reinforcement will be measured and paid separately.) (i) Using mixture machine. (A) In sub-structure upto plinth level. (N) Without using admixture, plasticiser, (b) M-20 or Proportion in 1:1.5:3

Providing formwork of formwork of ordinary timber planking so as to give a rough finish including centering, shuttering, strutting and propping etc. heigth of propping and centering below supporting floor to ceiling not exiding 4.0m and removal of the same for in situ reinforced concrete and plain concrete work in: Foundation, footings, base ofcolumn, pile cap, raft and mass concrete works etc. (b) Using 25mm thick plank

Columns, pilars, pots & Strut of quare/rectangular/polygonal in plain or any shape like Tee/L etc. Having plain vertical face. (ii) Using 25mm thick plank

Sides of tie beams, grade beams etc. at or below ground level.(b) Using 25mm thick plank

Sides and Soffits of Beams, beam haunchings, cantilever girders, bressumers, lintels and horizontal ties. (a) For depth not exceeding 1.0M. (ii) Using 25mm thick plank

Supplying, fitting and fixing in position reinforcement bars conforming to relevant I.S. Code for R.C.C. work/R.B. walling including straightening, cleaning, cutting and bending to proper shapes and length as per details, supplying and binding with 20G annealed black wire and placing in position with proper blocks, supports, chairs, spacers etc. complete (upto 1st floor level) (A) From primary produccer : TATA/SAIL/Jindal steel/Shyam steel/RINL (i) TMT Corrosion resistant steel (CRS) reinforecment bar(i) TMT Corrosion resistant steel (CRS) reinforecment bar

15 mm thick cement plaster in single coat on single or hulf bribkwall for interior plastering upto 1st floor level including arises, internal rounded angles, not exeeding 80 mm girth and finished event and smooth including curing completed as directed. (B) On fair side a) In cement mortar 1:3

Painting two coats (excluding priming coat) on new steel and other metal surface with enamel paint of approved brand and manufacture(Asian paint/ Berger paint/ ICI paint/ J & N paint/ Nerolac) to give an even shade including cleaning the surface of all dirt, dust and other foreign matter. (ii).Surfaces up to 100mm in width or girth. (a) Hiegh gloss (Assia paint / Berger paint / ICI paint/ J&K paint / Nerolac)

Providing welding, fitting, fixing, hoisting and fixing of Roof Trusses with purlin, bottom runner etc. fabricated out of combination of two or all of the following sections: (i) square hollow section (SHS) (II) Rectangular section(RHS) (iii) M.S. black tube conforming to relevant I.S. code 1161 - 1986 as per approved design and drawing including M.S, cleat, base plate, bolt and buts which ever reqired, including that required fixing the ceiling and one coat of red oxide Zinc chromate primer to all steel surface etc. completed as directed as per specifications. a) Using TATA make RHS/SHS of Grade 310 conforming to relevant I.S. code 4923 : 1997

Providing Pre Painted Galvanized Iron Sheet (PPGI) accessories (Ridges / Valley / Gutter /Flashing) at all levels including fitting and fixing self drilling, self tapping screws complete complete. TATA Blue scope/ Dyna roof / Durakolor /Wonder Roof or equivalent as directed by the Departement (iv) 0.60 mm thick

Providing polished tiles of approved quality, size, shape of specified thickness on pavers over a base of 100mm compacted sand gravel including cutting where necessary finished with flush pointing with Fix-A-Tile (Choksey / Sika / Pedelite / Rouf) /white cement slurry mixed with approved pigment to match shade of tiles complete at all levels as specified and directed. (Coloured pigment should be in conformity with colour of tiles and as approved and directed by the Department). (A) SUN ROCK HIGH CTS Tiles (Pavers) (a) Silicon (Pavers) 60 mm thick

Earth work in excavation for foundation trenches of walls, retaining walls, footings of columns, steps, septic tank etc., including refilling (return filling) the quantity as necessary after completion of work, breaking clods in return filling, dressing, watering and ramming etc. and removal of surplus earth with all lead and lifts as directed and specified in following classifications of soils including bailing out water where necessary as directed and specified. (A) Upto a depth of 2m below the existing ground l (b) In hard/ dense soil

Providing brick soling in foundation and under floor with stone/best quality picked Jhama brick, sand packed and laid to level and in panel after preparing the sub grade As directed including all lab our and materials and if necessary dewatering, complete. (A) Brick on flat soling.

Plain cement concrete works with coarse aggregate of sizes 13mm to 32mm in foundation bed for footing steps, walls, brick works etc. as directed and specified including dewatering if necessary, and curing complete (shuttering where necessary shall be measured and paid separately). (c) In prop 1cement: 5 sand :10 coarse aggregate by volume

Providing and laying plain/reinforced cement concrete works cement with coarse sand & 20 mm down graded stone aggregate including dewatering if necessary, and curing complete but excluding cost of form work and reinforcement for reinforced cement concrete work (form work and reinforcement will be measured and paid separately.) (i) Using mixture machine. (A) In sub-structure upto plinth level. Foundation, footings, columns with base, tie and plinth beam, pile cap, base, slab, retaining walls, walls of septic tank, inspection pit and the like and other works not less than 100mm thick up to plinth level. (N) Without using admixture, plasticiser, b) M20 grade concrete or Prop. 1:1.5:3

(B) In superstructure from plinth level to 1st floor level. (ii) Columns, pillars, posts, struts, suspended floor, roof, landing, shelf and support, balcony, lintel, sill band, beam, girder,bressumer, cantilever, staircase (except spiral stair case and landing) including preparing the top surface and finishing of nosing. (N) Without using admixture, plasticiser, b) M20 grade concrete or Prop. 1:1.5:3

Providing formwork of formwork of ordinary timber planking so as to give a rough finish including centering, shuttering, strutting and propping etc. heigth of propping and centering below supporting floor to ceiling not exiding 4.0m and removal of the same for in situ reinforced concrete and plain concrete work in: Sides of toe beams, grade beams etc. at or below ground leve. (b) Using 25mm thick plank

Column pillars, post & strut. (a) Square, rectangular, polygonal in plan or any shape like T / L etc. having plan vertical face. (ii) Using 25mm thick plank

Supplying, fitting and fixing in position reinforcement bars conforming to relevant I.S. Code for R.C.C. work/R.B. walling including straightening, cleaning, cutting and bending to proper shapes and length as per details, supplying and binding with 20G annealed black wire and placing in position with proper blocks, supports, chairs, spacers etc. complete (upto 1st floor level) b) Other ISI approved TMT reinforcement bar (SAI/BISCON/THERMAX) (For Assam Type Bldg., drain works,,retaining wall&boundary wall etc.

1st class brick nogged wall in cement mortar including racking out joints and curing complete as directed in super structure above plinth up to 1st floor level (protruding M.S rod/Tor steel of column to be embeded in cement mortar and will be measured and paid separately) (A) 112mm thick brick wall (a) In cement mortar in proportion 1:4. (1 cement:4 sand)

15 mm thick Cement plaster in single coat on single or half brick wall for interior plastering up to 1st floor level including arises, internal rounded angles, not exceeding 80mm girth and finished even and smooth including curing complete as directed. b) In cement mortar 1:4

20 mm thick Cement plaster in two coats on single or half brick walls for interior plastering up to 1st floor level including arises, internal rounded angles,chamfers and / or rounded angles not exceeding 80mm in girth and finished even and smooth including curing complete as directed. (A) On rough side b) In cement mortar 1:4

Supplying fitting and fixing M.S.angles, M.S. flat, M.S. bolts and nuts including painting with red lead paint one coat complete as directed. b) M. S. Flats / 38 x 38 square pipe…… M.S grill Wt. calculation for one span where Length of noe span in 1.20m. And vertical flate horizontal member etc as shown in the drawing.

a) Applying one coat of cement primer of approved brand and manufacture on new wall surface after throughly brooming the surfaces free from mortar droppings and other foreign matter and including preparing the surface even and sand papered smooth.

Earth work in excavation for foundation trenches of walls, retaining walls, footings of columns, steps, septic tank etc., including refilling (return filling) the quantity as necessary after completion of work, breaking clods in return filling, dressing, watering and ramming etc. and removal of surplus earth with all lead and lifts as directed and specified in following classifications of soils including bailing out water where necessary as directed and specified. (A) Upto a depth of 2m below the existing ground level (b) In hard/ dense soil

Providing brick soling in foundation and under floor with stone/best quality picked Jhama brick, sand packed and laid to level and in panel after preparing the sub grade As directed including all lab our and materials and if necessary dewatering, complete. (A) Brick on flat soling.

Providing and laying plain/reinforced cement concrete works cement with coarse sand & 20 mm down graded stone aggregate including dewatering if necessary, and curing complete but excluding cost of form work and reinforcement for reinforced cement concrete work (form work and reinforcement will be measured and paid separately.) (i) Using mixture machine.(A) In sub-structure upto plinth level.Foundation, footings, columns with base, tie and plinth beam, pile cap, base, slab, retaining walls, walls of septic tank, inspection pit and the like and other works not less than 100mm thick up to plinth level. (N) Without using admixture, plasticiser,b) M20 grade concrete or Prop. 1:1.5:3

(B) In superstructure from plinth level to 1st floor level.(ii) Columns, pillars, posts, struts, suspended floor, roof, landing, shelf and support, balcony, lintel, sill band, beam, girder,bressumer, cantilever, staircase (except spiral stair case and landing) including preparing the top surface and finishing of nosing. (N) Without using admixture, plasticiser,b) M20 grade concrete or Prop. 1:1.5:3

Providing formwork of formwork of ordinary timber planking so as to give a rough finish including centering, shuttering, strutting and propping etc. heigth of propping and centering below supporting floor to ceiling not exiding 4.0m and removal of the same for in situ reinforced concrete and plain concrete work in:Sides of toe beams, grade beams etc. at or below ground leve.(b) Using 25mm thick plank

Column pillars, post & strut.(a) Square, rectangular, polygonal in plan or any shape like T / L etc. having plan vertical face.(ii) Using 25mm thick plank

Supplying, fitting and fixing in position reinforcement bars conforming to relevant I.S. Code for R.C.C. work/R.B. walling including straightening, cleaning, cutting and bending to proper shapes and length as per details, supplying and binding with 20G annealed black wire and placing in position with proper blocks, supports, chairs, spacers etc. complete (upto 1st floor level) b) Other ISI approved TMT reinforcement bar (SAI/BISCON/THERMAX) (For Assam Type Bldg., drain works,,retaining wall&boundary wall etc.

230mm thick brick wall in cement morter with 1st class brick including racking out joints and curing complete as directed in structure (II) In superstructure above plinth level up to 1st floor level. (b). In proportion 1:4.(1 cement:4 sand)

15 mm thick Cement plaster in single coat on single or half brick wall for interior plastering up to 1st floor level including arises, internal rounded angles, not exceeding 80mm girth and finished even and smooth including curing complete as directed. b) In cement mortar 1:4

20 mm thick Cement plaster in two coats on single or half brick walls for interior plastering up to 1st floor level including arises, internal rounded angles,chamfers and / or rounded angles not exceeding 80mm in girth and finished even and smooth including curing complete as directed. (A) On rough sideb) In cement mortar 1:4

a) Applying one coat of cement primer of approved brand and manufacture on new wall surface after throughly brooming the surfaces free from mortar droppings and other foreign matter and including preparing the surface even and sand papered smooth.

Finishing old/ new wall with water proofing weather coat smooth anti-fungal exterior painting of Apex brand of Asian Paints and of required shade after cleaning and clearing the surface etc. including scaffolding complete as directed at all levels (two coats)

Supplying, fitting and fixing double leaf heavy duty iron gate, frame made from 50mm x 6mm M.S. flat iron with another horizontal flat at the middle, 20mm dia M.S bars at 200mm apart from bottom flat to top flat and 20 mm dia M.S. bars at 200mm apart from bottom flat to middle flat including drilling, welding etc. complete. All vertical bars are to be protruded at least 100mm above the middle and top flat is to be flattended and pointed as directed. Necessary locking arrangement on both faces, arrangement for temporary closing the gate and 2 nos.( minium) strong iron hinges of M.S bars and flat of same sizes on each leaf to be embeded in C.C brick pillars as necessary including a red oxide painting to all iron works as directed and specified. (Separate payment will be made for posts).

Appying priming coat over new steel and other metal surfaces upto 100mm in width or in girth after preparing the surface by thoroughly cleaning oil, greas, dirt and other forien matter and scoured with wire brushes, fine steels, wood scrapers and sand paper.(a) With ready mixed "red-lead / red oxide" primer.

Painting two coats (excluding priming coat) on new steel and other metal surfaces with enumal paint of approved brandand manufacture (Assian paint / Berger paint, ICI paint / J&K paint, Nerolac) to give an even shade including cleaning surfaces and all dirt,dust and other forien matter.(i) Surfaces over 100mm in width or girth.(b) Hiegh gloss (Assia paint / Berger paint / ICI paint/ J&K paint / Nerolac)

Supplying including and fixing of following Metal boxes for MODEL RANGE LEGRAND (ARTEOR), ANCHOR (AVE), MK (BLENZE), SCHNEIDER (ZENSELO), CRABTREE(MURANO) in surface/ recessed system complete as per direction of department. 3 module type Metal

6 module type Metal

8 module type Metal

9 module type Metal

12 module type Metal

Supplying including fitting fixing of following MODEL RANGE LEGRAND (ARTEOR), ANCHOR (AVE), MK (BLENZE), SCHNEIDER (ZENSELO), CRABTREE(MURANO) front plate of suitable colour as per direction of department. 3 module

6 module

8 module

9 module

12 module

Supplying with fitting fixing of 16 amp one way modular clip in switch, MODEL RANGE LEGRAND (ARTEOR), ANCHOR (AVE), MK (BLENZE), SCHNEIDER (ZENSELO), CRABTREE(MURANO) including making necessary connection as per direction of department.

Supplying with fitting fixing of 6/10 amp one way modular clip in switch, MODEL RANGE LEGRAND (ARTEOR), ANCHOR (AVE), MK (BLENZE), SCHNEIDER (ZENSELO), CRABTREE(MURANO) including making necessary connection as per direction of department.

Supplying with fitting fixing of 6/10 amp two way modular clip in switch , MODEL RANGE LEGRAND (ARTEOR), ANCHOR (AVE), MK (BLENZE), SCHNEIDER (ZENSELO), CRABTREE(MURANO) including making necessary connection as per direction of department.

Supplying including installation of socket outlet 6/16 Amps 3/5 pin combine shuttered complete , MODEL RANGE LEGRAND (MYLINC), ANCHOR (ROMA), MK (IVORY), ABB (CLASSIC), KOLORS (KRAZE), SCHNEIDER (OPAL), PHILIPS, Havells including making necessary connection as per direction of department.

Supplying including installation of socket outlet 6/10/13 Amps INTERNATIONAL SOCKET , MODEL RANGE LEGRAND (ARTEOR), ANCHOR (AVE), MK (BLANZE), SCHNEIDER (ZENSELO) including making necessary connection as per direction of department.

Supplying with fitting fixing of 6 amp one way modular clip in bell push with LED,MODEL RANGE LEGRAND (MYLINC), ANCHOR (ROMA), MK (IVORY), ABB (CLASSIC), KOLORS (KRAZE), SCHNEIDER (OPAL), PHILIPS, Havells including making necessary connection as per direction of department.

Supplying with fitting fixing of blank plate single in modular switch system MODEL RANGE LEGRAND (MYRIUS), ANCHOR (VIOLA), MK (WRAPAROUND/ PLUS), ABB (CHEIRON), KOLORS (KREST), SCHNEIDER (VIVACE), CRABTREE complete as per direction of department.

Supplying with fitting and fixing of 100 watt electronic modular fan speed controller 4 - Step 2 - module type MODEL RANGE LEGRAND (MYLINC), ANCHOR (ROMA), MK (IVORY), ABB (CLASSIC), KOLORS (KRAZE), SCHNEIDER (OPAL), PHILIPS, Havells including making necessary connection as per direction of department.

Wiring for drawing sub-main line with P.V.C. insulated single core unsheathed industrial (Multistrand) cable HFFR/ZHFR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR Kabel /Nicco or Equivalent Make as approved by the Deptt.) in PVC conduit (Berlia/ AKG / Precision/ Presto Plast/Polycab/ MW or equivalent make as approved by the Deptt.) with earth continuity in surface/ recessed 2 mm thick rigid low halogen SFT PVC IS: 9537 Part - III conduit wiring system. (a) with 2 x 2.5 sq. mm. + earth continuity with 1x1.5 sq. mm. in 20 mm. dia. rigid low halogen SFT PVC IS: 9537 Part - III conduit.

b) with 2 x 4 sq. mm. + earth continuity with 1x2.5 sq. mm. in 20 mm. dia. rigid low halogen SFT PVC IS: 9537 Part - III conduit

Supplying including installation of the Octagonal poles shall be designed to withstand the maximum wind speed of 169 km/hr. The top loading i.e. area and weight of fixtures are to be considered to calculate maximum deflection of the poles and the same shall meet the requirement of BS:5649 Part VI 1982. The pole shaft shall have octagonal cross section and shall be continuously tapered with single longitudinal welding. There shall not be any circumferential welding of the pole shaft. The welding of the pole shaft shall be done by Submerged Welding process. All octagonal pole shafts shall be provided with the rigid flange plate of suitable thickness with provision for fixing 4 foundation bolts. The base plate shall be fillet welded to the pole shaft at two locations i.e. from inside and outside. The welding shall be done as per process approved by Third Party Inspection agency. (BAJAJ/ PHILIPS/ VALMONT/ PARUTHI ENGR/Nezone make) The materials of the pole as follows : Conforming to grade S355JO Conforming to grade S355JO, Base Plate :- Fe 410 Conforming to IS 226/ IS 2062, Foundation Bolts :- 6.8 Gr. As per IS 1367, Pole Sections:- The Octagonal Poles shall be in single piece with single longitudinal welding join. Galvanization :- The poles shall be hot dip galvanized as per IS 2629 / IS 2633 / IS 4759 standards with average coating thickness of 65 micron. The galvanizing shall be done in single dipping. Door opening :- The Octagonal poles shall have door of approximate 500 mm length at the elevation of 500 mm from the base plate. The door shall be vandal resistance and shall be weather proof to ensure safety of inside connection as approved by the Depts.. The door shall be flush with the exterior surface and shall have suitable locking arrangement. The pole shall be adequately strengthened at the location of the door compensate for the loss in section. There shall also be suitable arrangement for the purpose of earthing, Smart pack Junction box with 6 MCB & Terminals for mounting inside base compartment of Pole. Top Dia. :- (A/ 70, Bottom Dia.:- (A/ 175, Sheet Thickness :- 3mm, Base Plate Dimensions :- (L x B x 275 x 275 x 16, Foundation Bolt Size:- (no. x dia.) 4 x 24 Dia, Pitch Circle Dia. (PC :- 270, Bolt Length:- 750, Projected Bolt Length :-125, Anchor plate thickness :- 4 mm, Pole Foundation :-The octagonal poles shall be bolted on a pre- cast foundation with a set of four foundation bolts for greater rigidity. Foundation :- The foundation shall be done with ( Earth work :- 2.04 cubic Meters.RCC :- 1:1.5 : 3 proportion 0.65 cubic metres. Steel:- 22.43 Kg. Shuttering :- 4.32 square metres. = 22.43 Kg.

Supplying including fitting and fixing of Hot Dip galvanised arm bracket for installation of luminaries. Header with top cap 300 mm long pipe of thickness 3 with arrangement to fix on pole top with 3 Nos. of bolts. i Armed of required length size 48.3mm out side dia x 3.25mm thick (BAJAJ/ PHILIPS/ VALMONT/ PARUTHI ENGR/Nezone make) Stiffener plate from arm of the following types : Single arm bracket 1000mm long for 3m to 10 metre. Poles.

Supplying with fitting & fixing of the following integral type street light luminaries complete and consisting of single piece integral epoxy gray powder coated dia cast aluminium housing gasket, pot optic reflector, cast aluminium frame from heat resistance toughened clear glass cover and accessories such as Condenser, lamp Holder, Ballast, lamp etc. in the existing pole including making necessary connection as approved by the Deptt.)with 2× 2.50 sq.mm F.R. multistrand and P.V.C. insulated single core copper cable as specified and directed by the department. Philips make) Cat No.SGP 301 1xCDMTT70W FG For Lamp 1xCDMTT70W (IP65) / Wipro: WSH 24070 For lamp 1x70W MHL / Crompton Greaves make) MHSGN1107IH/FG For lamp 1x70W MH/ Havells: LHBW07170036 For lamp 1x70W MH-

Supplying and installation and commissioning of vermin and dust proof totally enclosed double door cubical type compartmental floor mounting panel board of size 1.20 m ×1.00 m ×0.50 m made of 16 SWG1.66mm) thick CR sheet and 35 mm × 35 mm × 6 mm size angle and 35 mm ×6 mm flat iron having 4 nos legs at the bottom and G.I. Sheet reefing on the top complete painting with 2 coats of red oxide metal primer and 2 coats of enameled paint. The panel board is to be erected in 1:3:6 RCC pole foundation including excavation of trench and brick soling etc. complete neatly internal wiring done as specified and directed by the department comprising of the following electrical items. 1. 40 Amp 4 pole 415 Volt 50 Hz MCCB as incomer - 1 no 3. 25 mm × 5 mm size 4 strip copper Bus-Bar- 1 set 4. 40 Amp 4 pole ON-OFF poser contactor - 1 No. 6. 63 Amp bakelite HBC fuse kit-kat - 3 Nos

Supply, installation & testing of G.I. earth station with perforated 40 mm dia and 4.50 Metre long heady duty G.I. pipe with necessary 40 mm dia. G.I. Fittings such as Socket, Tee, elbow, nipple and 50 mmx40 mm G.I. reducing socket for funnel including locking arrangement 300 mmx300 mmx6 mm hinged cover C.I. earth plate complete with digging of earth pit, construction of brick chamber and plastering of both inner & outer surface of wall as specified and directed by the deptt .

Extra for using salt (5 K and Charcoal (64 K in pipe Earth Station pit to provide low impedance ground in location of high soil resistivity as and when required and specified by the Deptt.

Supplying & laying of 6 SWG G.I. earth from Earth Electrode (below G.L.) to electrical switch gears or electrical machineries including making necessary connection as approved, specified and directed by the deptt.

Supply and laying of following size PVC/XLPE insulated and PVC sheathed 1.1 KV G Solid Aluminium conductor up to 10 sq mm balance stranded conductor, XLPE Insulated, cores laid up, PVC tape inner sheathed, Armour (Aluminium for single core up to 70 sq mm balance Aluminium strip, Galvanised for cables up to 2x10 sq mm.3x10 sq mm,4x6 sq mm balance all galvanised steel strip) , extruded PVC Type ST2 sheathed, 650/1100V grade as per IS 7908(Part 1) 1988 armoured U.G. cable U.G. cable laid in ground/partially in air (as required for termination over ground including excavation of cable trench up to depth of 75cm, refilling, protective brick covering, Sand cushioning etc complete handling of surplus spoil, debris et to proper place as specified and directed by the deptt. (Nicco/ Havells/ RPG/CCI/Polycab/Gloster/ Finolex make) . 3 Core A2XWY A2XFY 4.00 Sq.mm 3 Core armoured U.G. cable

6.00 Sq.mm 3 Core armoured U.G. cable

3 & 1/2 Core A2XFY 35.00 Sq. mm.3 & 1/2 Core armoured U.G. cable

Supply and laying of following size Solid Aluminium conductor up to 10 sq mm balance stranded conductor, XLPE Insulated, cores laid up, PVC tape inner sheathed, Armour (Aluminium for single core up to 70 sq mm balance Aluminium strip, Galvanised for cables up to 2x10 sq mm.3x10 sq mm,4x6 sq mm balance all galvanised steel strip) , extruded PVC Type ST2 sheathed, 650/1100V grade as per IS 7908(Part 1) 1988, LT armoured U.G. cable laid in pucca flooring, road crossing, drain crossing as per site requirement and partially in air to connection as approved by the Depts. the control switch, through medium duty G.I. pipe (Tata/ Nezone make or equivalent as approved by the Deptt) bend and socket including excavation and refilling the trench and making good damage done as specified and directed by the deptt. (Nicco/ Havells/ RPG/CCI/Polycab/Gloster/ Finolex make) Core - 3 A2XWY A2XFY 4.00 Sq.mm 3 Core U.G. cable in 25mm dia medium duty G.I. pipe

6.00 Sq.mm 3 Core U.G. cable in 32mm dia medium duty G.I. pipe

Core - 3 & 1/2 A2XWY A2XFY 35.00 Sq.mm 3&1/2 Core U.G. cable in 50mm dia medium duty hot dip galvanised pipe (AKG or equivalent as approved by the Deptt.)

Supplying with fitting and fixing sheet steel cable junction box of size 40cm x 20cm x 15 cm made of 16 SWG thick MS Sheet with provision for hinge door and panel locking arrangement complete painted with 2 coats of metal primer and 2 coats of enamelled gloss paint of approved brand and manufacture to give an even shape including cleaning surface to remove of all dirt, dust and other foreign matter, the box is to be fitted on the bottom section of pole with minimum 165 mm dia 25 mm x 5mm size flat iron pole clamp complete with making necessary connection as directed consisting of the following electrical items.

Wiring for light/fan/call bell point with 2x1.5 sq. mm. P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR Kabel /Nicco / Anchor or Equivalent Make as approved by the Deptt.) in surface/ recessed conduit wiring system with 20mm dia 2mm thick / heavy rigid PVC IS: 9537 Part - III conduit (Berlia/ AKG / Precision/ Presto Plast/Polycab/ MW or equivalent make as approved by the Deptt.) including 6 Amp flush type switch/ bell push (Anchor penta /Gold medal /Kolor kany.Kom/Havells or equivalent make as approved by the Deptt.) GI/ MS switch board (ISI marked) with phenolic laminated sheet cover ,ceiling rose (Anchor penta /Gold medal /Kolor kany.Kom/Havells or equivalent make as approved by the Deptt.) etc. complete Short point up to 3.00 metre. length.

Medium point up to 6.00 metre. Length.

Long point up to 10.00 metre. Length.

Wiring for 5 pin 6 amp plug with 1.5 sq mm P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR Kabel /Nicco / Anchor or Equivalent Make as approved by the Deptt.) including 5 pin 6 amp socket outlet (Anchor penta /Gold medal /Kolor kany.Kom/Havells or equivalent make as approved by the Deptt.)make) and 6 amp flush type switch (Anchor penta /Gold medal /Kolor kany.Kom/Havells or equivalent make as approved by the Deptt.)make) earthing the 3rd pin of the socket as required on the switch board in surface/ recessed P.V.C. conduit wiring system. When fitted on same board of light and fan.

Wiring to 5 a pin 6 Amps plug point with 1.5 sq. mm P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR Kabel /Nicco / Anchor or Equivalent Make as approved by the Deptt.) in surface/ recessed 2 mm thick/ heavy rigid ISI marked IS: 9537 PART - III rigid PVC conduit (Berlia/ AKG / Precision/ Presto Plast/Polycab/ MW or equivalent make as approved by the Deptt.) wiring system including 5 pin 6 Amps flush type plug socket and 6 Amps F/T switch (Anchor penta /Gold medal /Kolor kany.Kom/Havells or equivalent make as approved by the Deptt.), GI/ MS switch board (I.S.I. mark with phenolic laminated sheet cover including earth continuity with 1.5 sq. mm. cable to third pin of the plug socket etc. as required complete, when placed elsewhere. Short point up to 3.00 metre. length.

Medium point up to 6.00 metre. Length.

Long point up to 10.00 metre. Length.

Wiring for 5/6 pin 16 Amps power plug point with 4 sq. mm. P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR Kabel /Nicco / Anchor or Equivalent Make as approved by the Deptt.) in surface/ recessed conduit wiring system including and fixing 5/6 pin 16 Amps flush type socket outlets and 16 Amps flush type switch ( Anchor penta /Gold medal /Kolor kany.Kom/Havells or equivalent make as approved by the Deptt.), GI/ MS switch board (I.S.I. mark with phenolic laminated sheet cover earth continuity with 2.5 sq. mm cable to the 3rd pin of the socket as required complete with 20 mm. dia. 2mm thick/ heavy ISI marked IS: 9537 PART - III rigid PVC conduit (Berlia/ AKG / Precision/ Presto Plast/Polycab/ MW or equivalent make as approved by the Deptt.) Short point up to 3.00 metre. length.

Medium point up to 6.00 metre. Length.

Long point up to 10.00 metre. Length.

Wiring for drawing sub-main line with P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR Kabel /Nicco / Anchor or Equivalent Make as approved by the Deptt.) PVC conduit (Berlia/ AKG / Precision/ Presto Plast/Polycab/ MW or equivalent make as approved by the Deptt.) including earth continuity in surface/ recessed 20 mm. dia. 2mm thick/ heavy ISI marked IS: 9537 PART - III rigid PVC conduit wiring system. With 2 x 2.5 sq. mm. + earth continuity with 1x1.5 sq. mm. in 20 mm. dia. 2mm thick/ heavy rigid PVC IS: 9537 Part - III conduit.

With 2 x 4 sq. mm. + earth continuity with 1x2.5 sq. mm. cable in 20 mm. dia. 2mm thick/ heavy rigid PVC IS: 9537 Part - III conduit.

With 2 x 6 sq. mm. + earth continuity with 1x 4 sq. mm. cable in 25 mm. dia. 2mm thick/ heavy rigid PVC IS: 9537 Part - III conduit.

Wiring for drawing sub-main line with P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR Kabel /Nicco / Anchor or Equivalent Make as approved by the Deptt.) in surface/ recessed PVC 20 mm. dia. 2mm thick/ heavy ISI marked IS: 9537 PART - III rigid PVC conduit (Berlia/ AKG / Precision/ Presto Plast/Polycab/ MW or equivalent make as approved by the Deptt.) wiring system. With 4 x 10 sq. mm. + earth continuity with 2x6 sq. mm. cable in 40 mm. dia. 2mm thick/ heavy rigid PVC IS: 9537 Part - III conduit.

Supplying and fixing of Jaquar or equivalent Philips/ Wipro LED down lighter fittings complete with Shade, back plate including connection cable, as approved by the Deptt.s etc. as required. LED Downlight,2*2,24W

Supplying and fixing of Jaquar or equivalent Philips/ Wipro LED ceiling light fittings complete with Shade, back plate including connection cable, as approved by the Deptt.s etc. as required. LED Ceiling Light 17W

Supplying and fixing of Jaquar or equivalent Philips/ Wipro LED round fittings complete with Shade, back plate including connection cable, as approved by the Deptt.s etc. as required. LED Round Light,6W

Supplying and fitting of 18/20 Watt CFL/LED lamp in the existing batten holder/angle holder/decorative bracket/bulk head fitting/ pendent holder etc. as specified and directed by the deptt.

Supplying fitting and fixing of retrofit T-5 lamp in the existing luminaries. PHILIPS/ CROMPTON GREAVES/ WIPRO/ BAJAJ/ Havells/ HPL/ SOLAR make. T5 LAMP WITH BOTH END connection cable, as approved by the Deptt.TOR WITH BALLAST 28 W

Supplying and fixing of Call bell ( Buzzer ) including 5/ 6 amp capacity button piano type bell push switch including connection as approved by the Deptt.)as required. [CB]

Supplying and fixing of Fan box (AKG or equivalent as approved by the Deptt.)with inbuild rod as required.

Supplying including fitting fixing of following A.C. Ceiling fan complete with all accessories like down rod, canopy etc. of following sweeps with making necessary connection as approved by the Deptt.)as required complete and as directed by the Department [Without regulator]. Premium model 1400 mm Sweep. (ORIENT PSPO make) /Premium model 1400 mm Sweep SS-390 Deco. Havells make)

Supplying fitting and fixing of ceiling fan Regulator including complete connections etc. complete as required and as directed by the department. Electronic Registrance Type

Supplying including fitting fixing of following A.C. Exhaust fan in the existing hole on the wall of following sweeps with making necessary connection as approved by the Deptt.)as required complete and as directed by the Department. Domestic Trans Air 300 mm sweep (Crompton make) [ EF ]

Supplying with fitting and fixing sheet steel, phosphatised, powder painted dust & vermin proof Double door IP-43 surface mounting SPN MCB DB incorporated with bas-bar, Neutral link, Earth bar and din rail etc fitted on wall with grouting nuts & bolts as reqd. complete with making necessary connection as approved, specified and directed by the deptt. ABB, Schneider MG, legrand, Hager make) 12 way SPN double door

Supplying with fitting and fixing sheet steel, phosphatised, powder painted dust & vermin proof reversible Double door IP-43 double door surface mounting horizontal TPN MCB DB incorporated with bas-bar, Neutral link, Earth bar and din rail etc fitted on wall with grouting nuts & bolts as reqd. complete with making necessary connection as approved, specified and directed by the deptt. ABB, Schneider MG, legrand, Hager make) 6 way TPN (8+18) double door

Supplying with fitting and fixing single Pole 10 KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, specified and directed by the deptt. C Series (Schneider MG, legrand, Hager make) 6 to 32A

Supplying with fitting and fixing DP 10 KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, specified and directed by the deptt. C Series (ABB, Schneider MG, legrand, Hager make) 40A

Supplying with fitting and fixing 4P 10 KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, specified and directed by the deptt. C Series (ABB, Schneider MG, legrand, Hager make) 40A

Supplying with fitting and fixing 30/100/300mA sensitivity 240/415V 50Hz DP RCCB of the following capacity complete with making necessary connection as approved, specified and directed by the deptt. 100/300mA sensitivity DP RCCB (ABB, Schneider MG, legrand, Hager make) 40A

Supplying including installation, commissioning of vermin and dust proof totally enclosed, Phosphatised Powder Painted cubical indoor type floor/wall mounting compartmentalize panel board of size 1.35M X 1.50MX 0.40M made of 16 SWG1.66 m thick C.R. sheet and 35mm X 35mm X 5mm size angle having 4 no legs at the bottom. The panel board is to be erected in 1 : 3 : 6 PCC foundation including brick soling / grouting etc. complete neatly Wiring done with provision for one no 125/160A 4pole MCCB or Switch Fuse Unit as incomer and provision for 8nos DP or TPN out going as specified and directed by the deptt. confirming to IP 43 protection comprising of the following electrical items: (Incoming & Outgoing Switch Gear of reqd. rating will be measured and paid separately)

Supplying with fitting and fixing panel mounting open execution 25 KA 415V 50Hz 3P MCCB (Ics=Icu, adjustable Ir setting 0.7) without enclosure of the following capacity complete with making necessary connection as approved by the Deptt. as specified and directed by the deptt. 25 KA 415V 50 Hz 3P MCCB (Schneider, legrand, Siemens make) 125A

Supplying with fitting and fixing Four Pole 415V Front handle operated On Load Change over switch (IP-20 protection powder painted sheet steel enclosure fitted on angle iron frame of the following capacity complete with making necessary connection as approved, specified and directed by the deptt. ABB, Schneider, legrand, L&T make) 125A

Supply and laying of following size PVC/XLPE insulated and PVC sheathed 1.1 KV G Solid Aluminium conductor up to 10 sq mm balance stranded conductor, XLPE Insulated, cores laid up, PVC tape inner sheathed, Armour (Aluminium for single core up to 70 sq mm balance Aluminium strip, Galvanised for cables up to 2x10 sq mm.3x10 sq mm,4x6 sq mm balance all galvanised steel strip) , extruded PVC Type ST2 sheathed, 650/1100V grade as per IS 7908(Part 1) 1988 armoured U.G. cable U.G. cable laid in ground/partially in air (as required for termination over ground including excavation of cable trench up to depth of 75cm, refilling, protective brick covering, Sand cushioning etc complete handling of surplus spoil, debris et to proper place as specified and directed by the deptt. (Nicco/ Havells/ RPG/CCI/Polycab/Gloster/ Finolex make) . 4 Core A2XWY A2XFY 35.00 Sq. mm.4 Core armoured U.G. cable

Supply, installation & testing of G.I. earth station with perforated 40 mm dia and 4.50 Metre long heady duty G.I. pipe with necessary 40 mm dia. G.I. Fittings such as Socket, Tee, elbow, nipple and 50 mmx40 mm G.I. reducing socket for funnel including locking arrangement 300 mmx300 mmx6 mm hinged cover C.I. earth plate complete with digging of earth pit, construction of brick chamber and plastering of both inner & outer surface of wall as specified and directed by the deptt .

Supply, installation & testing of Copper Plate earth station with 600 mmx600 mmx3 mm copper earth plate with necessary 40 mm dia. G.I. medium duty watering pipe with G.I. Fittings such as Socket, Tee, elbow, nipple and 50 mmx40 mm G.I. reducing socket for funnel including locking arrangement with 300 mmx300 mmx6 mm C.I. hinged cover plate complete with digging of earth pit, construction of brick chamber and plastering of both inner & outer surface of wall as specified and directed by the deptt .

Extra for using salt (5 K and Charcoal (64 K in pipe Earth Station pit to provide low impedance ground in location of high soil resistivity as and when required and specified by the Deptt.

Supplying & laying of 25X5mm size G.I. strips drawn on surface from earth electrode to Electrical switch gears, machineries etc complete with supply of G.I. nuts & bolts, screws etc including riveting, soldering & making necessary connection as approved, specified and directed by the deptt.

Supplying & laying of 8 SWG Copper. earth from Earth Electrode (below G.L.) to electrical switch gears or electrical machineries including making necessary connection as approved, specified and directed by the deptt.

Supplying & laying of 25X5mm size Copper strips drawn on surface from earth electrode to Electrical switch gears, machineries etc complete with supply of Brass nuts & bolts, screws etc including riveting, soldering & making necessary connection as approved, specified and directed by the deptt.

Supply, fitting & fixing 20 mmx5 mm G.I. strips drawn on vertically or horizontally on building wall/parapet wall in surface system complete with supply of G.I. Nuts & Bolts, Screws etc including riveting, soldering and making connection as approved by the Deptt.)with earth electrode G.I. strips and Lightning Arrestor etc. as specified and directed by the deptt.

Supply, fitting & fixing of Lighting Finial Arrestor made of 25 mm dia 300 mm long solid Copper tube having 85 mm dia. single prong at top and 3 mm thick base plate at bottom complete with fitting & fixing with Brass nuts & bolts on roof, RCC slab, top of column etc. as specified and directed by the deptt.

Supply, Installation, Fixing of CARBON DIOXIDE Fire Extinguisher confirming to IS: 2878 with ISI Mark.(4.5 LITERS) BRAND: FIRESTOP / FIREND / FIRESHIELD

Add 12% GST

Add Contingency Charge

Add Agency Charge

M/S P.D. ENTERPRISE

KARMAJYOTI DEURI