Civil Works

Amount

Dismantling the damaged floor finish and dadooing walls in cement mortar with mosaic tiles / Glazed tiles / cuddapah slab and clearing away with carefully stacking the material useful for re-use for any thickness etc., complete complying with standard specification and as directed by the departmental officer.

Dismantling the damaged doors and windows including removal of frames, hinges, fastenings and clearing away etc. complete complying with standard specification and as directed by the departmental officers.

Dismantling, Plain cement concrete and clearing away the same 50 m away from the site and roughening the surface etc., complete complying with standard specification and as directed by the Departmental officers.

Clean removal dust particles and Other materials in Exsisting Floor Surface and applying of bitumen paint 2 coats For Sunken portion of OTS and as Directed by the Departmental officers.

Dismantling AC Sheet roof including clearing away and carefully stacking the materials useful for reuse etc complete complying with standard specification and as directed by the departmental officers.

Dismantling the existing old damaged brick masonry under 3m height and carefully stacking the materials useful for reuse etc complete complying with std. Specification and as directed by the dept. officers.

Dismantling removing and carefully stacking pressed tiles with weathering course etc complete complying with standard specification and as directed by the departmental officers.

Providing Polymer Coating (brush bond RFX combination) for damaged terrace with following specification and the surface shall be cleaned to remove all dust, foregin, matters lose materials or any other deposits of contamination by rubbing with wire brush. Slurry: Dry blend and polymer liquid blend shall be mixed into the desired ratio as per recommendation of the supplier. The mix shall be stirred thoroughly until no bubbles remain in the mix. Any lumps found in mix shall be removed. Apply first coat of polymer modified cementitious slurry by brush on wet cleaned surface. After drying, second coat shall be applied on the first coat as directed by the departmental officers etc. The rate inclusive of cost of materials and labour, etc., complete.

Providing and Applying Polyurethane hybrid liquid applied GRIHA certified Waterproofing coating with flutyne protection technology, single component, cold applied, water based acrylic and UV resistant water proofing treatment to the Existing Roof having Tile or any non-porous surface applied @ 1.5 l/m2 in 2 coats to achieve 1mm DFT, having tensile strength with 45gsm glass fibre mesh 4N/mm2 confirming to ASTM D412; Elongation at break ≥ 300% and Crack bridgingability up to 3mm, SRI Index 106 as per ASTM E 1980-01, Water permeability @5 bar – Nil as per EN12390- 8:2019, including surface preparation, priming the surface with single component high-performance waterborne tile primer which is suitable for non -porous surface at a rate of 0.14 L/m2 and spreading 45gsm glass fibre mesh of 2.5 mm x 2.5 mm sandwichedbetween the first and second coat completely as perspecification. The finished cost to include surfacepreparation, making coving at Junction, treatment of cracks completely as per specification.

Earth work excavation for foundation by manual means for RR/Brick and Other step type footings for Load bearing structures in all soils and sub-soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the surplus earth within the compound in places shown by the departmental officers with an initial lead of 10 mts and initial lift of 2.00mts. and clearing and levelling the site, etc., complete complying with standard specification and as directed by the departmental officers.

Supplying and filling in foundation, basement with M-sand in layers of not more than 15 cm thick well watered, rammed and consolidated etc. complete complying with standard specification and as directed by the departmental officers.

Plain cement concrete 1:5:10 (one of cement, five of sand and ten of aggregate) using 40mm gauge hard broken granite stone jelly for foundation and basement including dewatering if found necessary and laid in layer of not more than 15cm thick and consolidated and curing etc., complete complying with standard specification and as directed by the departmental officers.- Mixing by manual means

Relaying Plain Brick jelly Lime Concrete 1:2:5 (One lime, two m-sand and five brick jelly) using 40mm brick jelly for foundation etc., including dewatering if found necessary and laid in layer of not more than 15cm thick compacting etc., complete complying with standard specifications and as directed by the departmental officers.

Relaying Cement Concrete 1:1-1/2:3 (One Cement, One and a half M-sand and Three hard broken stone jelly) using 20 mm gauge hard broken granite stone jelly for all RCC items of works excluding cost of reinforcement grill and fabricating charges centering and shuttering curing, etc. and providing fixtures like RCC floor / roof slabs wherever necessary and bearing surfaces of walls, beams etc. shall be finished smooth with Cement Mortar 1:3 (One Cement and Three M-Sand) and kraft paper laid over it without claiming etc., complete complying with standard specification and as directed by the departmental officers.

Foundation & Basement

For First Floor

For Second floor

Supplying and erecting steel centering including necessary supports For plane surfaces such as rectangular or square RCC columns etc. which require only nominal strutting using mild steel sheets made of 10 gauge thick welded with MS angle size 40mm x 40mm x 5 mm and supported by Steel Adjustable Telescopic Props of Size 2m x 2m (expandable upto 3.60m) made with outer steel pipe with dia 50mm (3.60mm thick) and inner steel pipe with dia 40mm (2.90mm thick).etc..complete in all floors complying with standard specifcation. Steel Adjustable telescopic props shall be provided as directed by the departmental Officers. (Payment for centering shall be given after the concrete is laid).

Brick work in Cement Mortar 1:5 (one of cement and five of m-sand) using best quality Burnt Clay Brick of size 9" x 4 3/8" x 2 3/4" with class designation of 7.5 conforming to IS 1077-1992 for foundation and basement including Cost of Mortar Plasticizer curing, etc.,complete complying with standard specification and as directed by the departmental officers. Brickwork shall be done as per IS 2212-1991 adopting English Bond generally.other type of bond shall be done as directed by the Executive Engineer in charge.

Foundation & Basement

Second floor

Rectification of beams, column and slabs by dismantling and chippling the distressed portico clearing of reinforcement with wire brush and by sand blasting, clearing and water washing applying corrosion inhibitor coating at the rate of 1.20kg/m2 over the affected surface as per the specification given by the manufacturing guniting with CM 1:3 (one cement and three P-sand) to an average thickness of 40mm under pressure and finished neatly including hire charges for all tools & plants labour, fuel charges including all leads for portable water including curing 7 days and all other incidental charges etc., complete complying with standard specification.

Special ceiling plastering and finishing the exposed surface of all RCC items of work such as slabs, beams, sunshades, facia, canopy slab, staircase waist slab, landing slab etc., with Cement Mortar 1:3 (One Cement and Three Plastering Sand) 10mm thick including mortar plasticizer at 200ml per 50Kg of cement used, hacking the surfaces and curing, etc., in all floors complying with standard specification and as directed by the departmental officers.

Plastering with Cement Mortar 1:5 (One cement and Five Plastering sand), 12mm thick in all floors including mortar plasticizer at 200ml per 50Kg of cement used, curing etc. complete complying with standard specification and as directed by the departmental officers. (Data as per new Data book SL. No.297)

Flooring with ceramic tiles of size 305x305x6mm and variety conforming to IS 15622 laid over cement mortar bed of 20 mm thick in cement mortar 1:3 (One Cement and Three crushed stone Sand) with required Cement Slurry and Mortar Plasticizer including cutting the tiles to the required size with special cutter wherever necessary, laying in position and pointing with Water Resistant Tile Epoxy Grout at the rate of 0.27 Kg. / sq.m etc., complete complying with standard specification and as directed by the departmental officers. (The make and brand of the tiles should be got approved by Executive Engineer before use on works) (Data as per new Data book Sl.No.257)

Dadooing walls with following best approved quality, white / colour glazed tiles conforming to IS 15622 of size 300 x 450 x 8mm in Cement Mortar 1:2 (One Cement and Two crushed stone sand),10 thick with Mortar Plasticizer and pointing the joints with Water Resistant Tile Epoxy Grout at the rate of 0.27 Kg. / sq.m. neatly in all floors, curing, etc., complete complying with standard specification and as directed by the departmental officers.(The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Paving the floor with best approved quality fine polished Kota stone slabs of size 600 x 600 of 18 / 20mm with machine cut edges and matching marble slab not less than 100mm width other than Adanga Marbles as border laid over a cement mortar bed of 20mm thick using cement mortar 1:3 (One cement and three M-sand) fixing the slabs in true right angles with minimum possible width of joints and pointing the joints with white cement mixed with mathcing colouring pigments and polishing with floor polisher to a high degree of finish etc., The kota stone slabs and other materials to be used shall be got approved by the Executive Engineer concerned before use on work, etc., complete as per standard speicification.

Renewing the old and damaged flooring tiles and laying with new C.C. Laminated tiles (Like Dora tiles Eurocon tiles, etc.), pre-polished concrete anti-skid tiles (Required shape and design) of 20mm thick of approved quality and colour laid in accordance with IS 1443 over a cement mortar bed of 20mm thick in Cement Mortar 1:3 (One Cement and Three crushed stone sand) with required Cement Slurry and Mortar Plasticizer and pointed with white cement mixed with colouring pigment at the rate of 0.40 Kg. / sq.m., curing, etc., complete complying with standard specification and as directed by the departmental officers. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Finishing the top of roof with one course of machine pressed tiles of size 230mm x 230mm x 16 mm to 18mm approved quality set in Cement Mortar 1:3 (One Cement and Three Crushed stone Sand) 12mm thick mixed with water proofing compound conforming to ISS at 2% by weight of cement used and the joints pointed neatly to full depth of tiles with the same cement mortar mixed with red oxide and water proofing compound including curing etc., complete complying with standard specification and as directed by the departmental officers.

Easing and repairing hanging doors, window shutters and refixing the same after attending the petty repairs including fixing furniture fittings and excluding cost of furniture fittings etc., complete complying with standard specification and as directed by the departmental officers.

Supply & fixing of WPC door shutter, extruded as a single core board with rigid WPC compound with the thickness of 25mm (+/- 1mm) & minimum Bulk Density of 550 KG/Cub.Mt. & shore hardness of 55. The door shall be a plain matt board as decided by the Engineer in-Charge of the department. The WPC door shall be fixed onto the Aluminium “G” type channel with Wheel and the door shall have 2 Hooks in SS, 2 Handles 4” in SS (Sliding door) etc., complete and as directed by the departmental officers.

Fabricating, Supplying and fixing in position Mosquito net arrangements of Sliding type. The Outer Sliding frame shall be made with Powder coated Aluminium Natural colour matt finish Aluminium Hollow section of size 40mmx38mmx1.55mm. The Horizontal and Vertical Aluminium Hollow section Slidingtrack shutter frame of size 20mmx44mmx1.55mm. The Mid Horizontal Aluminium Hollow section frame provided in the sliding track shutter with a size of 10mmx11mmx1.55mm. The Epoxy coated Stainless Steel 304 grade wire mesh with dia of 0.19mm shall be provided for Net. The Mosquito net arrangement should be fixed to the window with 100% packing with Screws, Silicon packing all around the frames with including cost of all materials, labours, power consumption required for fabrication, drilling holes in RCC column/wall, masonry walls, Window frames, wherever necessary with drills to the required extent and make good to the original conditions after fixing and also as directed. All the Aluminium sections are to the powder coated with matt finish under electrically controlled conditions in accordance with relevant IS Code etc. complete complying with standard specification and as directed by the departmental officers.

Providing Cup-board Shutter using termite / water proof plywood of 19mm thick over which laminated sheet of 0.8mm thick fixed inside the shutter and 1mm thick fixed in the outside of the shutter using fevicol along with necessary furniture fittings, such as, hydralic hinges, tower bolt,handles, multi purpose locks etc., as directed by the Departmental Officers. The design pattern, water proof plywood, laminate sheet and other materials should be got approved from the Executive Engineer befoe use on work.

Removing and refixing the following Furniture fittings of apporved quality and make including labour charges for fixing inposition as directed by the departmental officers.

75mm long and 10mm dia Tower Bolts

100mm long Handles

75mm pad lock stainless steel

75mm x 30mm Butt Hinges

Renewing and refixing of PVC Trims (Beading) for Dadooing including cost and conveyance etc., complete complying with standard specification and as directed by the departmental officers.

Renewing the Glass Panes 4mm thick with new plain/pin headed/Figured glass panes including fixing inposition with teakwood beeding of size 30x12mm alround the glass panes with nail etc., complete.

Providing and Fixing of polyurethane foam for Sloped roof as thermal insulation panels or Sandwich insulated panels with external 0.50mm total coated thickness pre painted Galvalume sheet with trapezoidal roofing profile having crest height of 38mm at every 333mm span, whereas internal 0.50mm total coated thickness pre painted galvanized iron sheet with micro ribbed profile and the insulation material will be chlorofluoro carbon and hydro chlorofluoro carbon free, high performance rigid polyurethane foam (PUF) conforming to IS 12436 having density not less than 40±2Kg/M3, Thermal conductivity (K-Value) 0.024 W/m.K measured at 10 degree C mean temperature along with necessary flashings such as L flashing, C flashing etc& accessories such as screws ,fastners ,sealants etc for fixing the panel etc., complete complying with standard specification.

Renewing the partition with new one of Aluminium anodized powder coated finish alu partly glazed partition pre laminated board partition with aluminium box section of with 63.50mm x 38.10mm x 1.28mm, 1.41mm @ 81.8 Kg/m extruded box section at bottom, and horizontal members are spaced at 90cm center to center and to vertical member are spaced at 1.20m, 2.10m, and 2.80m, height from floor level, panels, should be covered with 9mm thick PLB Exterior grade with 4mm thick plain glass necessary aluminium clips of size 19mm x 17.30mm x 0.90mm @ 0.124Kg/m, 'L' angle, screws etc., The aluminium surface is to be anodized with matt finish, under electrically controlled condition in accordance with ISI 1868/1962 specification for an average anodic film thickness. The rate is inclusive of cost of materials, converyance, scaffolding if any required etc., and necessary dismantling making holes in RCC masonry, brick masonry wherever necessary with power drill to the extent required and made good to the original condition after fixing the partition as directed by the departmental officers. All materials should be got approved by the Executive Engineer before fixing inposition.

Supplying and fabricating and fixing in position aluminium door anodized Powder coated finish partly top 1/2 glazed and partly bottom 1/2 panelled door and frame made out of box section 101.60x44.45x3.18mm thick at 2.319 kg/m door shutter made out of box section 47.1x44.45x2.5mm at 1.202 kg/m for vertical style and top, lock rail sections of size 50x44.50x2.5mm @ 1.292 k/m and bottom 100.4x44.45x2.50mm at 1.974kg/m using clips of size 17.15x17.27x1.5mm at 0.176kg/m with necessary metal screws, rubber beading, strike plate type handle of size 100x30x1.60mm at 0.988 kg/m on both sides, tower bolts, lock pivot arrangements and top 1/2 portion with 5.50mm thick plain glass and bottom 1/2 portion with one side prelaminated board (MDF) 12mm thick for panel portion with 1 No. of hydraulic door closers of approved quality using aluminium extruded section body tubler type universal with double speed adjustment with ISI monogram including cost of furniture fitting such as Pivot, hinges, Tower bolt, lock, door stopper and all materials labour power consumption required for fabrication drilling required for fabrication drilling holes in RCC columns floor slabs masonry wall wherever necessary with power drills to the required extent and make the same to original condition after fixing and as directed. All the aluminium sections are to be anodised with matt finish under electrically controlled condition in accordance with IS 1868-1962 for an average anodic film thickness of 15 microns etc., complete. The materials should be got approved by the Executive Engineer before use on works. The rate shall be inclusive of all materials, labour for fixing transportation loading, unloading and all other incidential charges.

Renewing and refixing the Medium Desity Fibre (MDF) Board - Exterior Grade, both sides pre-lamiated including external lipping with kiln dried soft wood 35mm thick and 5.50mm thick glass panes, furniture fitting such as 3 nos 4"brass butt hinges, 2nos 6"brass tower bolts, 2nos 4"brass handle, 1 no brass drop, single key shutter, mortice lock without night latch, 1 no door closer, 1 no brass door stopper etc., complete complying with standard specification.

Renewing the old damaged vertical blinds premium as per the following specification the fabrication 100x150mm colour and white of fabric vanes to have bottom packed the same materials as the vane stablishing weight is to be located in the shutter in plastering moulding to be but in the top side of bottom paacked as all fabric vanes to be sufficiently high quality materials were finished not tray one use in norml all the fabric is opened by rails manufacture from extruded aluminium powder coated in the standard colour rate inclusive of labour charges for fixing etc., complete complying with standard specification and as etc.,complete complying with standard specification and as directed by the departmental officers.

Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Louvered Ventilators of from the profile the size of outer frame 60mm x 58mm and shutter profile size of 60 x 78mm both profiles are reinforced with GI/1mm 125GSM and 100% corrosion free, the profile are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with all over the edges of frame and shutter. The corners and joints should be welded and cleaned. Radiations pin headed glass 4mm thick should be provided in the louvers. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The ventilator should be got approved from the Executive Engineer before use on work.

Supplying and fixing in position of new mild steel grills for gates, doors, ventilators and windows using M.S flats and square rod etc. The rate is inclusive cost of all materials, labour for fixing, including one coat of primer etc. complete complying with standard specification and as directed by the departmental officers. (Data as per new Data book Vol II Sl.No.63)

Supplying and fixing in position 15 mm dia Brass Chromium Plated Screw down tap (Heavy type), Pillar tap and Angle Cock of approved make conforming to IS specification and quality including cost of shellac, thread, cutting and threading wherever necessary etc., complete complying with standard specification and as directed by the Departmental officers. (Taps should be got approved by the Executive Engineer before use on the works).

15mm dia Brass screw down tap

15mm dia Pillar tap

Angle Cock

Renewing and fixing new one of best quality approved make white glazed earthenware wash hand basin (White Without Pedestal) of size 550x400mm with a pair of cast iron brackets, including cost of 15mm dia Brass chromium plated pillar tap, 32mm dia CP waste, 32mm dia PVC waste pipe with rubber plug and chain, 15mm dia G.M wheel valve, 15mm dia brass nipple, 15mm dia nylon connection etc. including fixing the wash hand basin in the wall in position with a pair of CI brackets with TW plug and screws and giving necessary water supply connection and painting the brackets with two coats of paint over a priming coat of anticorrosive paint including testing for leakages etc., complete.

Supplying and fixing in position white glazed European Water Closet of best quality and approved make with 100 mm "P" or "S" trap connecting with CI pipe of 100mm dia / PVC pipe of 110mm dia, double flapped rigid PVC black seat and seat cover with CP brass hinges including cost of white cement, cement for packing, spun yarn, teak wood plugs, brass screws, etc., including supplying and fixing 10 litres capacity PVC / 12.5 litres capacity porcelin low level flushing tank with a pair of CI brackets, etc., complete with all fittings such as 15mm brass ball valve with polythene float with brass handle, union, coupling connected.

Renewing and fixing new one of Indian water closet Oriya type of size 580x875.6mm,White glazed earthenware of approved quality with 'P' or 'S' trap confirming to IS:2556-part -XII with sand cushion and forming flooring alround the closet using 40mm broken brick jelly in lime concrete 1:2:5 (one lime, two sand and five brick jelly)100 mm thick and finishing the top to required slope and including giving necessary connection to cast iron soil pipes by dismantling brick masonry, RCC/ floor slab and making good the dismantled portion to original condition without leakages etc. complete.

Renewing the damaged PVC Rainwater downfall pipe 110mm dia of approved quality and design approved quality including fixing inposition to true alignment with necessary shoes, special, clamps, bends, cowl, screws, nails, teakwood block. The rate inclusive of fixing the same in to true alignment etc., complete complying with standard specification and as directed by the departmental officers.

Supplying and fixing position CI Nahani Trap / Floor Trap of the following sizes with best stainless steel gratings of approved brand and quality, fixed over a bed of brick jelly lime concrete 1:2:5 (One part of lime, two part of crushed stone sandand five part of 40mm gauge brick jelly) and finished with Cement Mortar 1:3 (One Cement, Three sand) including dismantling masonry works wherever found necessary and making good the dismantled portions to the original condition and giving connection to the CI / PVC pipes, etc., complete complying with standard specification. (The Nahani Trap should be got approved by the Executive Engineer before use on works) (Data as per new Data book Vol II Sl.No.663)

Supplying and Fixing Stainless Steel Health Faucet special type with new one including the cost of labour and fixing charges etc., complying with standard specification and as directed by the departmental officers.

Supplying and fixing in position Indian make bevelled edge mirror of approved quality and brand PVC / Fibre Glass framed 5.5mm thick mirror of following size , Shelf type with hard board backing of approved colour fixed with brass screws, rawl plug, etc., complete complying with standard specification. (The mirror should be got approved by the Executive Engineer before use on woks) Size :600 x 450 mm / 500 x 400mm / 1000 x 780 mm.

Supplying and fixing approved best quality brass CP towel rail 600mm long and 20mm dia with brackets of same materials including cost of teak wood plugs and CP screws, etc., complete complying with standard specifications. (The tower rail should be got approved by Executive Engineer before use on works).

Supplying and fixing best approved best quality brass CP soap tray of size 150 x100mm including cost of teak wood plugs, brass screws, etc., complete complying with standard specifications. (The soap tray should be got approved by Executive Engineer before use on works).

Supplying and fixing in position CP shower rose with CP stop cock arrangement of size 15mm dia inlet and 100mm outlet to the pipe line with necessary cutting, threading and jointing using shellac etc., complete complying with standard specification and as di- rected by the departmental officers (The CP shower rose should be got approved by the Executive Engineer before use on works).

Supplying, laying and jointing UPVC pipes of following dia Class 5 (having working pressure of 10 kg/sq.cm) conforming to IS 4985- 2000 of approved quality and best variety of the following dia including cutting and fixing UPVC specials using UPVC adhesives (but excluding cost of such specials) in accordance with IS 7634-3 (2003) and fixing into wall with teak wood plugs, PVC clamps and screws making holes on the wall (or) drilling holes in the roof and making good the dismantled portion to original condition with necessary brick work / cement concrete and plastering neatly wherever necessary with necessary scaffolding charges upto 4 metre height above ground level, etc., complete complying with standard specifications. The PVC pipes shall be got approved by Executive Engineer before use on works - External water supply above ground level

32mm dia UPVC pipe

25mm dia UPVC pipe

20mm dia UPVC pipe

Supplying and fixing with new following UPVC specials of approved quality and make including fixing and finishing neatly in position as directed by the departmental officers etc. complete.

20mm dia UPVC Elbow

25 mm dia UPVC Elbow

32mm dia UPVC Elbow

20 mm dia UPVC Tee

25 mm dia UPVC Tee

32mm dia UPVC Tee

Supplying and fixing inposition first quality and approved variety UPVC Ball Valve 32mm dia including cost of shellac, thread, labour charges for cutting, threading, fixing inposition etc, complete complying with standard specification and as directed by the departmental officer both internal and external water supply arrangements.

Supplying and fixing in position best quality PVC soil / waste pipes of various dia having 6 kg / sq.cm. pressure BIS mark and providing leak proof joints using PVC adhesives including fixing to the wall with special PVC / MS clamp, teak wood plugs, brass screws, etc., and making connection to all sanitary fittings, dismantling masonry / RCC works wherever found necessary and making the good dismantled portion to the original condition, including testing for any leakages, etc., complete complying with standard specifications. (The PVC pipes should be got approved by the Executive Engineer before use on works). The rate for earth work excavation will be measured and paid separately in the cases where the pipe lines are proposed to laid below ground level

PVC pipe 75mm dia

PVC pipe 110mm dia

PVC pipe 160mm dia

Supplying and fixing in position PVC specials of the following dia and types of approved quality confirming to BIS and providing leak proof joints including fixing to the walls and giving connection to the PVC soil stacks, dismantling the masonry or RCC works and redoing the dismantled portion to original condition etc., complete complying with standard specifications. (The PVC specials should be got approved by the Executive Engineer before use on works).

75mm dia PVC Elbow with Door

110mm dia PVC Elbow with Door

75mm dia PVC Tee with Double Door

110mm dia PVC Tee with Double Door

Construction of INSPECTION CHAMBER CLEAR SIZE 0.60 X 0.60 including earth work excavation, CC 1:5:10 of 10 cm thick and brick work in Cement Mortar 1:5 [One cement and Five sand] using best quality of Clay burnt Bricks of size 9” x 43/8” x 23/4” with Class designation of 7.5 and Plastering with Cement Mortar 1:3 [One Cement and Three Plastering Sand] 12 mm thick to inner and outer sides and wearing coat 1:3:6 [One Cement, Three crushed stone sand and Six Aggregate] 15 cm thick and covered with precast slab 5 cm thick etc., complete complying as directed by the departmental officers as per standard specification.

Distempering the Two Coats of approved quality including preparation of surface, the rate includes cost of brushes, high scaffolding arrangements, neat finishes, etc., complete complying with standard specification and as directed by the departmental officers.

Painting Old Plastered Wall Surface with Two finishing coats of ready mixed Exterior (Emulsion) of approved quality and colour over the existing wall in all floors etc., complete complying with standard specification and as directed by the departmental officers. (The make, quality and colour of paint should be got approved by the Executive Engineer before use on works.)

Painting Old wood work with Two coat of synthetic enamel ready mixed paint of approved quality and colour in all floors etc., complete complying with standard specification and as directed by the departmental officers. (The make, quality and colour of paint should be got approved by the Executive Engineer before use on works.)

Painting Old iron works such as steel doors, windows, ventilators, window bars, balustrades etc., with Two coats of best approved first quality and colour of synthetic enamel paint in all floors etc., complete complying with standard specification and as directed by the departmental officers.(The make, quality and colour of paint should be got approved by the Executive Engineer before use on works.)

Collecting the scattered debries from the campus and conveying away the same to outside by lorry to a lead of 3km (Entirely within city limit) including loading and unloading charges and dumping in low places and levelling neatly etc., complete complying with standard specification and as directed by the departmental officers.

REJE COATING SYSTEMS PVT LTD (BID ID -1500936)

B. SANKARAAN (BID ID -1500788)