SPECIAL REPAIR TO BUILDING NO P-19 (9 OR MD ACCN) IN RAIPUR LINE UNDER GE JAMMU

Amount

B/R PORTION Taking down chowkats or frame with shutters (without taking off shutters from the frames) area not exceeding 1.5Sqm each, complete all as specified.

Taking down chowkats or frames with shutters (without taking off shutters from the frame) area exceeding 1.5Sqm and not exceeding 4Sqm each, complete all as specified and directed.

Demolition of cement concrete (un-reinforced) in ground floors and paving not exceeding 15cm thickness (below or above ground level), complete all as specified and as directed.

Taking down cement plaster on stone or brick walls etc including racking out joints, hacking for key scrubbing down with water etc.complete all as specified.

Excavation in trenches not exceeding 1.50m wide and not exceeding 1.50m in depth for cables not exceeding 10sqm on plan and not exceeding in depth and getting out soft/disintegrated rock for cable and pole, complete all as specified.

Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing complete all as specified.

Supply and fixing factory made solid core PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC sheet, 'C' channel having PVC sheet strip of 20mm width stuck inside with solvent cement for styles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap inserted for top rail and bottom rail; panelling of plain colour PVC sheet to be fitted in MS frame welded/ sealed to the stiles and rails with suitable PVC sheet beading and joined together with solvent cement complete all as specified & shown in relevant drawing of item No. 08080 in MES Schedule (Part-II) and directed by Engineer-in-Charge.

S&F Pressed steel frames for door (Factory made) out of 1.25 mm thick black MS sheet, with one or more rebates including necessary fixing lugs, butt hinges, lock strike plate, etc. complete, size of frame 105x60mm incl bottom of each chowkat to be welded with 2 Nos 25x25x3 mm thick flat iron projecting 10 cm on either side and back fill to chowkats with PCC 1:3:6 type C-0 using 12.5 mm graded crushed stone aggregate including one shop coat of red oxide primer complete all as specified and directed.

S&F Pressed steel frames for door (Factory made) out of 1.25 mm thick black MS sheet, with one or more rebates including necessary fixing lugs, butt hinges, lock strike plate, etc. complete, size of frame 125x60mm incl bottom of each chowkat to be welded with 2 Nos 25x25x3 mm thick flat iron projecting 10 cm on either side and back fill to chowkats with PCC 1:3:6 type C-0 using 12.5 mm graded crushed stone aggregate including one shop coat of red oxide primer complete all as specified and directed.

M&L for 18/19 mm thick prelaminated particle board interior grade prelaminated one side with decorative choice lamination & other side balancing white lamination fixed with screws to timber frame work as in cupboard shelves/pelmet box including teak wood beading all around all as specified & directed.

S&F for solid PVC frame for cupboards Ivory colour of size 50 mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube in opening including fixing lugs, hinges etc complete all as specified.

S&F for 35 mm thick 2nd class hard wood plain framed, panelled shutter (two panel) of factory made with lock rail and panel of 12 mm thick veneered particle board with commercial veneering on both faces including wooden beads on both sides, one coat of pink primer. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified.

S&F for 35 mm thick 2nd class hard wood factory made glazed and Skelton shutters open rebated and prepared to receive glass/wire gauge etc. without sash bar but with lock rail edges of framing plain, chamfered or rounded fitted with cut and mitered beads for securing glass/wire mesh etc sizes of member as per clause 8.20(a) of SSR part -I for door shutter complete all as specified.

S&F steel window 1.25 mm thick Box type (Primer coated) ERW hollow P section of size 60 x 25 mm single rebated comprises glazed Skelton shutter ERW sec 50 x 20 mm and 1 mm thick with two Nos sash bar of T- section 20 mm x 3 mm complete welded to frame with one vertical mullion of ERW box type T-section of size 60 x 25 mm and 1.25 mm thick including cutting holes and making good dismantled portion in PCC 1:2:4 type B-1 four No for each window incl following fitting welded to frame shutter hold fast of 150 mm long of 12 mm x 3 mm FI made to shape 4 No, handle of Z section 20 mm x 25 mm x 100 mm long 1 No per leaf, MS tower bolt 150 mm long 2 No per leaf, Z sec 20 mm x 25 mm, 100 mm long stopper 1 No on per leaf, MS pintal hinges of size 75 mm x 12 mm 2 No per leaf fabrication and fixing arrangement as per drg No CEPZ/TD-324,325/07 complete all as specified.

S&F steel window 1.25 mm thick Box type (Primer coated) ERW hollow P section of size 60 x 25 mm single rebated comprises wire gauged Skelton shutter ERW sec 50 x 20 mm and 1 mm thick with two Nos of FI section complete welded to frame for holding wire mesh with one vertical mullion of ERW box type T-section of size 60 x 25 mm and 1.25 mm thick including cutting holes and making good dismantled portion in PCC 1:2:4 type B-1 four No for each window incl following fitting welded to frame shutter hold fast of 150 mm long of 12 mm x 3 mm FI made to shape 4 No, handle of Z section 20 mm x 25 mm x 100 mm long 1 No per leaf, MS pintal hinges of size 75 mm x 12 mm 2 No per leaf fabrication and fixing arrangement as per drg No CEPZ/TD-324,325/07 complete all as specified.

S&F Mild Steel work of flat iron, square bar, round bar etc. as in framed work such as grills, guard bars, gratings, etc. including bending, cutting and welding as necessary of confirming to Fe 290-0 Gde-E-16 including one shop coat of zinc chromate primer complete all as specified.

M&L for PCC 1:2:4 type B1 using (20 mm graded stone aggregate) as in blocks for hold fasts, benching, coping apex stones, bed plates and the like including weathering, slightly rounded or chamfered angles and throating, all as specified and directed. Note : From work required for these item included in the unit rate of this item.

Sheet glass ordinary quality, 3mm thick, glazing with oil putty or wooden beads in squares not exceeding 0.50Sqm in each pane, complete all as specified.

Figured glass pin headed type, 3mm thick, glazing with oil putty or wooden beads in squares not exceeding 0.50Sqm in each pane, complete all as specified.

Galvanised mild steel wire cloth 0.56 nominal dia of wire and average width of aparture 1.00mm and fixed with tinned tacks or galvanised wire staples, complete all as specified.

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc complete all as specified

Dismantling floors hearth or wall tilling including cement mortor bedding (but not backing) removing unserviceable materials outside MOD area and rubbish off the premises.

Glazed ceramic coloured tiles (300x200mm) x 7mm thick, as in vertical surfaces such as in skirting and dado etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles laid over and including 10mm thick back coat layer in cement mortar 1:4, complete all as specified and directed by Engr-In-Charge.

Non skid coloured ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.06sqm but not exceeding 0.11sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shed of tiles, laid over and including 15mm thick screed bed in CM (1:6), complete all as specified.

Non skid coloured ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.11sqm but not exceeding 0.18sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shed of tiles, over and including 15mm thick screed bed in CM (1:4) complete all as specified and directed.

M&L for Green Marble work 18 to 20 mm thick (table rubbed and polished ) in stapes jambs, pillars, window cill, cooking platform and like in cement mortar (1:4) including 20mm thick screed in CM 1:6 and pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of marble complete all as specified.

25 mm thick PCC 1:2:4 type B-0 (using 12.50mm graded crushed stone aggregate) as in floor finishing surface even and rough using extra cement,complete all as specified.

WC Orissa pattern white with integral foot rest 580 x 440 mm including PCC bedding 1:2:4 and making good disturbed floor connecting to trap and flush pipe complete all as specified.

PVC (SWR) P trap 110/110 mm bore complete all as specified Make Supreme/Finolex

PVC low level flushing cistern 10 Ltr capacity white with inlet ball value, float valve and handle inc brackets, PVC flush pipe complete all as specified.

PVC connection 15 mm bore and 450 mm long including brass check nut at both ends screwed for iron pipes of 15 mm bore complete all as specified.

Pillar taps 15 mm dia, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed suitable for 15 mm bore complete all as specified.

Vitreous China wash basin, white, flat back, size 580x450 mm including 32 mm dia PVC waste pipe, CP brass waste coupling 32 mm dia, pair of MS brackets or MS fastener/bolts for fixing arrangements and 450 mm long PVC connection with PVC nut and washer complete at site and all as directed.

Bib taps 15mm bore of cast copper alloy chromium plated fancy type, screwed down, high presure with crutch or butterfly handle, screwed both ends for iron pipe or for brass ferrule, fixed in repair, complete all as specified and directed.

15mm bore Stop valve cast copper alloy chromium plated fancy type with long shank and cup (concealed type) screwed down high pressure with crutch or butter-fly handle, screwed both ends for iron pipes or for union, fixed in repairs, complete all as specified.

Brass chromium plated shower rose 125 mm size swivel type with connecting rod 15 mm bore complete.

Stop valve cast copper chromium plated concealed type screwed down high pressure with capstan head suitable for 15 mm bore complete all as specified.

Stainless steel gratings of outer frame dia 150 mm open able type incl all necessary fitting such as hinges including embedding in tiles with white cement.

M&L for rendering 15 mm thick cement plaster 1:4 on other than fair faces of brick work or concrete surfaces and to be finished even and smooth without using extra cement.

M&L for rendering 10 mm thick cement plaster 1:6 on fair faces of brick work or concrete surfaces and to be finished even and smooth without using extra cement.

M&L for rendering 5 mm thick cement plaster 1:3 on fair faces of concrete surfaces as in ceiling, chajja, shelves etc. finished even and smooth without using extra cement.

M&L for rendering 15 mm thick cement plaster 1:3 on other then fair faces of concrete surfaces as on facia of roof slab, chajja, shelves etc. finished even and smooth without using extra cement (incl all necessary scaffolding, lifting arrangment for three story building on external surfaces) complete all as specified.

S&F for Harrison rails mild steel chromium plated with fixing brackets etc complete all as specified.

Taking up/down steel tubing of 15mm bore pipe and connection laid in trenches or floors or fixed to walls and including cleaning for refixing or removal to store with all fittings, Complete all as specified and directed.

Taking up/down steel tubing of 20mm bore pipe and connection laid in trenches or floors or fixed to walls and including cleaning for refixing or removal to store with all fittings, Complete all as specified and directed.

Steel water tubing of 15 mm bore ‘medium grade’ galvanized with all fittings like socket, union, elbow, bend, tees etc fixed to walls and ceilings or laid in floors, complete all as specified.

Steel water tubing of 20 mm bore ‘medium grade’ galvanized with all fittings like socket, union, elbow, bend, tees etc fixed to walls and ceilings or laid in floors, complete all as specified.

Fixing only 15 mm bore old galvanised pipes incl new fittings where necessary fixed complete to wall and ceiling or laid in floor as specified.

Fixing only 20 mm dia bore galvanised pipes incl new fittings where necessary fixed complete to wall and ceiling or laid in floor complete all as specified.

Cutting chases for concealed water tubing or concealed conduit & making good in CM 1:3 girth exc 10 cm and n.exc 20 cm in brick wall

75 mm thick PCC 1:3:6 type C-2, using 40 mm graded stone aggregate as in plinth protection complete all as specified.

Taking down CI pipes 100 mm dia incl all fittings like bend, branch pieces, connectors, heel rest bend etc all as specified and directed.

Taking down CI pipes 75 mm dia incl all fittings like bend, branch pieces, connectors, heel rest bend etc all as specified and directed.

PVC SWR pipes 110 mm bore single socketed in any length with rubber joint fixed to wall or laid in trenches or in floor with steel clamps all as specified and directed,

PVC SWR pipes 75 mm bore single socketed in any length with rubber joint fixed to wall or laid in trenches or in floor with steel clamps all as specified and directed,

PVC SWR bends of 110 mm bore

PVC SWR bends of 75 mm bore

PVC (SWR) junction double (double T) equal or unequal provided with access door of 110 mm dia complete all as specified.

PVC (SWR) junction single (single T) equal or unequal provided with access door of 75 mm dia complete all as specified.

PVC (SWR) floor trap plain including jointing with solvent cement 75 mm dia complete all as specified.

PVC (SWR) reducer of 110 mm dia complete all as specified.

PVC (SWR) vent cowl 75 mm bore complete all as specified.

PVC (SWR) WC connector with lip ring 110 mm complete all as specified.

Mild steel helical/ordinary rat tail rod pattern door spring 300 mm including roller and roller plate complete fixed with welding all as specified (ISI marked)

Small fittings IInd class hardwood such as brackets of any types latch and hings blocks shaped door and window stops and the like, not exc 200 cu cm each all as specified.

Mild steel sliding door bolt 200 mm long plate type stove enamelled black with bright bolt not less then 12 mm dia with the incl a min of 6 bolts and nuts four on bolt plate and two on staple plate all as specified.

100 mm long hasp and staple, aluminium anodixed with bolt to hinge palte and fixed with screws.

Aluminium tower bolt of size 150 mm complete all as specified.

Aluminium handle of size 150 mm complete all as specified.

Dismantling/disconnecting/demolition of water storage tank of any type or description PVC exc 250 litre and n.exc 500 Ltrs capacity and removing from site or refixing in position.

Rotational moulded polythylene water storage tank with float valve, plastic lid cover, triple layered, cylindrical verticl with closed top hoisted and fixed in position of capacity 500 Ltr incl making connections complete all as specified.

Repairs stop valve 20 mm dia cast copper alloy, secrewed down high pressure with crutch or butterfly handle secrewed both ends for iron pipe and fixed complete all as specified.

One coat of synthetic enamel paint tint over old painted steel surfaces over 10 cm in width or girth including preparation of old surfaces of steel.

Preparation of new steel surface exc 10cm width or girth and applying two coats of synthetic enamel paints over priming with red oxide all as specified.

Preparation of new wood or wood based surface and applying two coats of synthetic enamel paint over one coat of pink primer, all as specified.

Two coats of oil bound distemper of wall to newly plastered surfaces including preparation of surfaces complete all as specified and directed

Two coats of oil bound distemper of wall to old plastered surfaces including preparation of surfaces complete all as specified and directed

Preparation of old plastered surfaces including filling of small holes etc and applying two coat of white wash over wall surface complete all as specified.

Preparation of surfaces old plastered surfaces & applying two coats of white wash over two coat of white wash on ceiling complete all as specified.

Preparation of surfaces new plastered surfaces & applying three coat of white wash on ceiling complete all as specified.

Two coats of cement base paint to newly plastered surfaces including preparation of surfaces complete all as specified and directed

Two coats of cement base paint to old plastered surfaces including preparation of surfaces complete all as specified and directed

Stainless steel kitchen sink in repairs with drainage board made of stainless steel of 1 mm thick sheet including plugs, washers and pvc waste pipe of 40 mm dia. Fixing with complete on appropiate size of cantilever brackets of MS angle or GI pipe 15 mm dia with proper arrangment to hold and fitting of sink and connecting union to pipe. The overall size of sink 915mm x 460mm and bowl size 410mm x 330mm x 160mm complete all as specified.

Removing existing treatment from roof surfaces such as tiling, tarfelt, fungus,moss,dust etc.,cleaning the surface of all foreign material by wire brushing and dusting and racking out RCC slab complete all as spd and removing the debries outside defence land.

Rendering 20 mm thick in CM 1:4 on fair face of brick work surfaces finished even and smooth without using extra cement up including mixing liquid water proofing compound complete all as specified.(Note- liquid water proofing compound shall be measured and paid separately)

Roof Treatment with the following specification :- (a) Applying evenly one coat of Bituminous Primer conforming to IS 3384-1986, @ 0. 3 ltrs per sqm over cleaned plastered surface. (b) Applying evenly one coat of blown Hot Bitument of Grade 85/25 @ 1.2 Kg per sqm on primed surfaces. (c) Applying a layer of APP based Polymeric Memberance 3mm thick (Minimum) weighing 3.5 Kg per sqm (reinforced) with polyster Non woven fabric weighing not less than 160 gms per sqm by torch application. The overlap shall be minimum 100 mm on traverce direction and 75 mm on longitudinal direction and sealing overlap by torch application. (d) Applying evenly one coat of Aluminium paint @ 0 .10 Ltr per sqm over the APP based polymeric Membranecomplete all as specified.

E&M PORTION:- Taking down carefully unsv aluminium / copper conductor point wiring (light, fan, light socket, power socket) complete fitting such as swithes, sockets, lamp holder, utility light fitting, fan regulator etc and removing materials from sites and making good distrubed surface of walls and roofs complete all as specified and as directed.

Taking down carefully unsv DBS ,mainswitches etc of any sizes making good disturbed surfaces of walls and floors complete all as specified and as directed.

Point wiring with 1.5 Sqmm single core multi stranded copper conductor FRLS insulated and unsheathed heavy duty cable in colour code including contineous earth wire with cable of size 1.5 sqmm copper conductor flexible FRLS insulated drawn in and including concealed PVC rigid conduit medium grade ISI marked terminated into CI/pressed steel terminal boxes including 3.00mm thick laminated sheet cover of hylam brand IS-2036 marked, for mounting switches, sockets, fan regulators etc for one light/fan/bell point controlled by one, one way switch including cutting chases and making good to disturbed surfaces of wall / ceiling / floor including treating with existing finishes, complete all as specified and as directed.

Description all as per srl item No-90 here in before but for one 3 pin socket outlet 6 amp as on independent board complete all as specified.

All as per item No. 90 above but for 3 pin 5 Amps on same board with cable 1.5Sqmm size, all as specified and directed

All as per item No. 90 above but for one bell / buzzer point on same board or independent board with cable 1.5Sqmm size, all as specified and directed

Description all as per srl item No 90 here in before but for one 3 pin socket outlet 15 Amp independent with cable of size 2.5 Sqmm for main wiring and 1.5 sqmm as in continuous earth wire.

Description all as per srl item No 90 here in before one light point controlled by 2 way switches with cable of size 1.5 Sqmm for main wiring and 1.5 sqmm as in continuous earth wire.

One 3 pin socket outlet 6 amp independent complete all as specified.

Lamp holder PVC/Polycarbonate type with back plate suitable for batten fittings with and including LED lamp 9Watt, 240 volts complete all as specified and directed.

Switch piano flush type 6 Amp single pole one way, (ISI marked), complete all as specified.

Switch socket multipurpose combination 2 in 1, 3 pin, 5 and 15 Amp flush type universa controlled by one switch ,complete all as specifed.

Ceiling rose (ISI Marked) 3 terminals PVC/poly carbonate, insulated body, compete all as specified.

Bell push (ISI Marked) flush type 5 amp , compete all as specified.

Electric bell ding dong type 230 volts AC supply all as specified and directed by Engineer-in-Charge.

S & F i replacement of powder coated Sheet metal enclosures factory made, (Double door) for DBs, single pole and neutral, 240 volts, 8 ways with 200Amp rated busbar fixed on walls, including connecting both incoming and outgoing cable termination with proper taping, lagging, testing and commissioning, complete all as specified and directed.

Fan regulator two module 80 W, stepped type (electronic ) flush type for 1200/1400mm sweep AC ceiling fan, complete all as specified. .

LED Tube light fitting 18 watt wall mounted LED batten rod extruded aluminium heated sink provided for efficient heat dissipation and integrated electronic driver , complete all as specified. Make:-Havells or equivalent cat part of make as specified in Appx "F" here in after.

MCB triple pole and neutral 63amps 415 volts 50 Hz, B 'series ' 10 KA breaking capacity, complete all as specified.

MCB single pole and neutral 32 amps 240 volts 10 KA 'C' series fixing in replacement, all as specified.

Sheet metal enclosures factory made, (Double door) for DBs, Triple pole and neutral, 415 volts, 4 ways with 200Amp rated busbar fixed on walls, including connecting both incoming and outgoing cable termination with proper taping, lagging, testing and commissioning, complete all as specified and directed.

MCB single pole and neutral 6-32 amps 240 volts 10 KA 'C' series fixing in replacement, all as specified.

Earthing complete with galvanised mild steel earth plate electrode of size 600x600x6mm thick burried directly in ground earth (in vertical) earth pit not less than 2.25 mtr deep below normal ground level with top edge of the earth plate not less than 1.5 mtr below ground level connected to galvanised iron or earth lead wire 4mm dia (8 SWG) by means of nut, bolt, check nuts and washer of galvanised iron including PCC pit in PCC 1:2:4 type B-1 pre-cast RCC cover slab using reinfocement with XPM weighing not less than 1.87 kg/Sqm with suitable handle made of 12mm round bar, including necessary excavation and earth work in any type of soil, 20mm dia medium grade galvanised steel tube for watering with one end fixed with cast iron funnel and wire mesh, 15mm dia bore light grade galvanised steel tubing upto 7.5 m length for drawing earth lead wire protection pipe, common salt, charcoal, etc complete all as shown in electrical plate No 3 of SSR Part-I and testing on completion. Note:- Rate for earth lead wire & protection pipe upto 7.5mtr length are inclussive in this item & no extra payment shall be admissible for the same.

Supply laying jointing and testing LT XLPE and PVC insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 35 sq. mm 3.5 core complete all as specified

Sand filling underneath and all around the UG cable in trenches for cable cushioning including required watering and consolidation complete all as specified and directed

Supply and laying sub class `B` bricks laid dry flat transversely along the length of cable with width equal to the length of bricks over sand cushioning as protection cover of cable laid, complete all as specified.

Returning, filling, including spreading, leveling, watering and well ramming in layers not exceeding 25 cm in any soft distintegrated soil, complete all as specified and directed.

Removing excavated material (soil) to a distance not exceeding 50m and depositing where dircted at a level not exceeding 1.50m above the starting point, all as specified and directed.

S&F in replacement of GI pipe light grade 40 mm bore for cable protection fixed on poles or laid in trenches, under floor path culverts, ducts etc with complete accessories such as bends sockets reducers,saddles including necessary threading , drilling works fixing clamps, nuts bolts etc all as specified.

LED Street light fitting of 50 watt powder coated pressure die cast aluminium compact high power LED street light with heat resistant toughned glass with lens complete with, brackets and all accessories complete all as specified, NOTES:- Rate is inclusive of bracket of suitable sizemade of GI medium grade pipe 1.2 mtr long bend to shape 120 degree and fixing with 2 nos of suitable size clamps including nuts washers bolt complete fittings.

M/s Sekinder Paul Sharma