SPECIAL REPAIR TO BLDG NO T-09 AND LBW WORK AT LGJ MIL STN

Amount

B/R Portion Demolition of cement concrete (unreinforced) in ground floor and paving n.exc 15cm in thickness (below or above ground level) complete all as specified and directed by Engr-in-charge.

Demolition of reinforced cement concrete of any description and in any position not otherwise specificlly provided for (reinforcement cut as required to facilitate demolition) complete all as specified and directed by Engr-in-charge.

Demolition of brick work or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stone work and precast concrete articles complete all as specified and directed by Engr-in-charge.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing rubbish off the premises complete all as specified and directed by Engr-in-charge.

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust etc. complete all as specified and directed by Engineer-in-Charge.

Taking down cement plaster on brick / stone walls including raking out joints, hacking for key, scrubbing down with water complete all as specified and directed by Engr-in-charge.

M&L for joint free non skid ceramic coloured tiles 7 to 8 mm thick (square/ rectengular) area of each tile exc 0.18 Sqm but not exc 0.38 Sqm in floor over and including 15 mm thick screed bedding in cement mortar 1:6, set and jointed in neat cement slurry and pointed in coloured cement to match the floor complete all as specified and directed by Engr-in-charge.

M&L for joint free non skid ceramic coloured tiles 7 to 8 mm thick (square/ rectengular) area of each tile exc 0.18 Sqm but not exc 0.38 Sqm on vertical surfaces such as skirting / dados over and including 10 mm thick backing coat in cement mortar 1:4, set and jointed in neat cement slurry and pointed in coloured cement to match the floor complete all as specified and directed by Engr-in-charge.

M&L for joint free non skid ceramic coloured tiles 7 to 8 mm thick (square/ rectengular) area of each tile exc 0.06 Sqm but not exc 0.11 Sqm in floor over and including 15 mm thick screed bedding in cement mortar 1:6, set and jointed in neat cement slurry and pointed in coloured cement to match the floor complete all as specified and directed by Engr-in-charge.

M&L for glazed ceramic coloured tiles of size 350 X 250 X 7 mm / 450 x 350 x 7 mm thick on vertical surfaces such as skirting / dados over and including 10 mm thick backing coat in cement mortar 1:4, set and jointed in neat cement slurry and pointed in coloured cement to match the floor complete all as specified and directed by Engr-in-charge.

M&L for 20 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed by Engr-in-charge.

Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situationscomplete all as specified and directed by Engr-in-charge.

M&L for 75mm thick PCC (1:4:8) type D2 using 40mm graded stone aggregate as in sub-base complete all as specified and directed by Engr-in-charge.

M&L for precast cement concrete 1:2:4 type B1 using 20mm graded stone aggregate as in kerb stones size 300mm x 300mm x 100mm with plain fair faces, including chamfers, weathering, throating etc setting in CM 1:4 complete all as specified and directed by Engr-in-charge.

M&L Machined pressed precast concrete interlocking paver block glossy with grey cement and pigment, any shape and size confirming to IS 15658-2006 of 60mm thickness M-35 grade over 50mm thick Fazilka sand cushion complete all as specified and directed by Engr-in-charge.

Formwork to chullah hoods, chajjas, troughs and similar items including edges , for rough surface of concrete, complete all as specified and directed by Engineer-in-charge

M&L for reinforced cement concrete 1:1.5:3 type A-1 using 20mm graded stone aggregrate in Chajjas;complete all as specified and directed by Engr-in-charge. Note : Reinforcement shall be measured and paid seperately.

S&F mild steel TMT bars (Fe-500D) 10mm dia and over,cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mmdia or securing with clip complete all as specified and directed by Engr-in-charge.

S&F mild steel TMT bars (Fe-500D) 6mm to 8mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clip all as specified & directed by Engineer-in-Charge.

M&L for rendering, 15 mm thick on brick work or concrete surfaces in cement mortar 1:6 on wall finished even and smooth without using extra cement complete all as specified and directed by Engr-in-charge.

M&L for rendering, 10 mm thick on brick work or concrete surfaces in cement mortar 1:4 on ceiling finished even and fair complete all as specified and directed by Engr-in-charge.

M&L for two coats of oil bound distemper on newly plastered surfaces of walls paint over a coat of primer over 3mm thick wall care putty including preparation of surfaces complete all as specified and directed by Engr-in-charge.

M&L for complete removal of existing treatment and two coats of oil bound distemper over 3 mm thick wall care putty on plastered surfaces of walls including preparation of surfaces complete all as specified and directed by Engr-in-charge.

M&L for 3 coats of white wash on newly plastered surfaces incl preparation etc. complete on wall complete all as specified and directed by Engr-in-charge..

M&L for 3 coats of white wash on old plastered surfaces incl preparation etc. complete on ceiling complete all as specified and directed by Engr-in-charge..

M&L for two coats of cement base paint on newly plastered surfaces incl preparation and over a coat of alkali resistant primer complete on wall complete all as specified and directed by Engr-in-charge.

M&L for broken brick boulder hard core of gauge, deposited, spread and levelled in layers n exc 15cm thick watered and rammed to a true surface complete all as specified and directed by Engr-in-charge..

M&L for 75 mm thick PCC 1:3:6 type C-2 using 40 mm graded mechanically crushed stone aggregate as in plinth protection finished even and smooth without using extra cement with & including 10 mm wide, 30 mm deep joints at the rate of 3.00 mtr centre to centre and at every turning & filling the joints with bitumen & sand mixture complete all as specified and directed by Engr-in-charge.

M&L continous brick edging with fly ash bricks old size bricks, with width equal to the width of the brick; liad dry on end vertically complete all as specified and directed by Engr-in-charge.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth for foundation, etc. and getting out hard/dense soil complete all as specified and directed by Engr-in-charge.

M&L for PCC 1:4:8 type D2 using 40mm graded stone aggregate in foundation, filling & mass concrete complete all as specified and directed by Engr-in-charge.

M&L for brick work with fly ash bricks, old size bricks, straight or curved on plan exc 6m mean radius, built in CM 1:6 complete all as specified and directed by Engr-in-charge.

M&L for brick work with fly ash bricks, old size bricks straight or curved on plan to any radius in half brick thick walls, built in CM 1:4 complete all as specified and directed by Engr-in-charge.

M&L for PCC 1:2:4 type B2 using 40mm graded aggregates as in benching / haunchig of manholes including forming channels including necessary formwork etc. complete all as specified and directed by Engr-in-charge.

M&L for PCC 1:2:4 type B1 using 20mm graded aggregates as in coping and the like including weathering, slightly rounded or chamfered angles and throating, as directed including necessary formwork etc. complete all as specified and directed by Engr-in-charge.

M&L precast cement concrete 1:2:4 type B1 using 20mm graded stone aggregate and set cement mortar 1:6 as in cover slabs (for manholes etc,) chajjas, shelves and similar articles with plain faces complete all as specified and directed by Engr-in-charge.

M&L Rendering 10mm thick on fair face of brick work in cement mortar 1:4 and finished surfaces even and smooth with using extra cement as specified including WPC complete all as specified and directed by Engr-in-charge. Note : - (WPC shall be measured and paid seperately)

M&L moorum/red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering complete all as specified and directed by Engr-in-charge.

Supply and laying DWCPE (SN8) drain pipes 150mm inner dia as per IS-16098 (Part-II), laid in trenches on moorum bed to required slope, including all assessories / fittings, jointing and tested complete all as specified and as directed by Engineer-in-Charge. (Make :- Rex Polyextrusion Limited/ Dura line / Alom Poly Extrusions Ltd / Jain Irrigation

Returning, filling in, including spreading levelling including watering & well ramming in layers n. exc 25 cm any type of soil complete all as specified and directed by Engr-in-charge.

Removing excavated material n.exc 50m and depositing where directed at a level n.exc 1.50 m above the starting point complete all as specified and directed by Engr-in-charge.

Cutting into existing manholes for connection of new drain making pipes and rendering cutting out existing benching & forming branch channel in PCC 1:2:4 type B1 smooth finished & forming benches as reqd etc for 150 mm bore complete all as specified and directed by Engr-in-charge.

M&L preparation of new steel surface of any description not otherwise described over 10 cm width or girth and apply two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed by Engr-in-charge.

Dismantling of brick tiles in floor laid dry and pointed in cement morter complete all as specified and as directed by engineer-in-Charge.

Demolition mud in roofs, any thickness, including plastering and leeping complete all as specified and directed by Engr-in-charge.

M&L PCC (1:7:12) using 40mm graded stone aggregate as filling of sunken floors/bottom and side of drain complete all as specified & directed by Engr-in-charge.

M&L for rendering 15mm thick on brickwork or concrete surfaces in cement mortar 1:4 and finished fair and even including mixing of WPC in mortar complete all as specified and directed by Engr-in-charge.

Supply only integrated water proofing compound complete all as directed by Engr-in-charge. Make:- Dr Fixit/Fosroc/BASF/STP

Material and labour for creating fillet caving 50x50mm with polymer modified mortar on the junction of slab and wall as per manufacture instructions, Material and labour Providing for applying two coats of two component (1 part Liquid: 2 part Powder) ready to use cementitious waterproof coating on properly prepared surface by brush having elongation of >50% for the applying water proofing treatment as per following and complete all as directed by the EIC. (i) Applying 1st coat of two components modified polymer coating on horizontal and verticle surfaces. (ii) Provn of glasses fiber mess of 2x2mm immediately on alone coating. (iii) Applying 2nd coat of two components modified polymer coating after 72hrs on horizontal and verticle surfaces. NOTE:- Complete treatment to be carried out by authorised applicatior of waterproofing manufacture. Make : Dr Fixit/Fosroc/BASF/STP

M & L APP based membrance minimum weighing 3 KG per sqm and minimum 3mm thick reinforced with polyster non woven fabric (wt not less than150 gms/sqm) laid on primed surface by torced application with APP membrane over a coat of aluminum paint over 10mm thick screed bed in CM 1:3 mixing of WPC in mortar complete all as specified & directed by Engineer-in-charge. Note : Brick tiles shall be measured & paid separately under respective item of this BOQ

M & L Lime concrete terracing as specified in roof (excluding bitumen tack coat) complete all as specified and directed by Engr-in-Charge.

M&L PCC 1:2:4 type B-1, using 20mm graded stone aggregate as in roof kerbs or mud stops, rounded or chamfered on edges including necessary form work etc complete all as specified & directed by Engr-in-Charge.

Taking down chowkhats or frames n.exc 1.5 sq. m each with shutters (without taking off shutters from the frame) complete all as specified and directed by Engr-in-charge.

Taking down chowkhats or frames exc 1.5 sq. m but n.exc 4.0 sq. m each with shutters (without taking off shutters from the frame) complete all as specified and directed by Engr-in-charge.

Taking down wooden shutters of any description exc 1 Sqm and n.exc 2 Sqm each and removing from site complete all as specified and directed by Engr-in-charge.

S&F framed work as in chowkats of doors windows of angle iron ,gates or other section with gusset plates, rails, braces etc conforming to Gde Fe 410 or Fe 310 complete all as specified and directed by Engineer-in-Charge.

S&F hold fast of flat iron 25 x 3 mm conforming to Fe-290 or Fe 330 including preparing the surfaces & treated with two coats for coaltar & sanded with clean sharp sand complete all as specified and directed by Engr-in-charge.

M&L for Cement concrete 1:3:6 type C–1 (using 20mm graded crushed stone aggregate) as in coping, hold fast, bed blocks or similar block etc complete all as specified and directed by Engr-in-charge.

S&F powder coated aluminium frame/shutter for doors, windows, ventilators and aluminium partition with one or more rebates including jointing cleats glazing clips, rubber packing, anodised aluminium snap beading, screws etc complete with locking arrangements for fixing with powder coating on aluminium sections, minimum thickness of poweder coating shall be 50 micron as per the specification. The top and bottom horizontal members and vertical members adjacent to wall shall be fixed with floor, ceiling, walls and cills where required and fixed with the help of rawl plugs and screws or with fixing clips or with expansion hold plate fastners. Aluminium section shall be smooth, rust free, straight, mitred and jointed mechanically whereever required complete in all respect all as specified & directed by Engr-in-Charge. Make of Al Section : Jindal / Hindalco / NALCO

S&F Neoprene / EPDM rubber gasket all as specified and directed by Engineer-in-Charge. Note : Taken for other other than door/window shutter if reqd)

Supply and fixing of Fibre glass Reinforced plastic (FRP) door frame of required built in colour in three legged of cross-section 90mm x 45mm having single ribate of 32mm x 15mm to recieve shutter of 30mm thick including laminated door frame moulded with fire retardant grade unsaturated polyster resin and chopped strand mat(CSM) also door frame laminated shall be 2mm thick and shall be filled with suitable wooden block of 2nd class hard wood in all three legs frame shall be covered with fibreglass from all sides MS stay flat iron 25mm x 3mm shall be provided at the bottom to steady the frame complete all as specified and as directed by Engineer-in- charge.

Supply and fixing of 30 mm thick glass fibre reinforced plastic (FRP) paneled doorshutter conferming to IS:14856-2000 of required colour and made with fire retardant grade unsaturated polyster resin,moulded to 3mm thick FRP laminated for forming hollow rails and style with suitable second class hardwood timber block inside at required places for fixing of fittings,cast molithically with 5mm thick FRP laminated for panels including fixing to frames, complete all as specified and as directed by Engineer-in- charge.

S&F 100 mm long butt hinge, extruded aluminium alloy with galvanised mild steel hinge pin, anosied and fixed type B-21 complete all as specified and directed by Engr-in-charge.

S&F 200 mm long aluminium anodised barrel tower bolt, of extruded sections complete all as specified and directed by Engr-in-charge.

S&F 150 mm long aluminium anodised handle, cast type complete all as specified and directed by Engr-in-charge.

Taking down existing shutter and refixing in same opening shutters of any description exc 1.0 Sqm but not exc 2.0 Sqm each all as specified and directed. Note:- 'Refixing' includes taking down, easing and adjusting and also refixing builders hardware as required including renewal of unserviceable screws, etc.

S&F 35 mm thick 2nd class hard wood factory made plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated all as directed.

S&F 35 mm thick 2nd class hard wood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a) all as directed.

S&F 100 mm long butt hinge, medium weight, cold rolled mild steel complete all as specified and directed by Engr-in-charge.

S&F for 300mm long aluminium alloy, anodised, sliding door bolt type not less than 16mm dia with and including nuts and bolts fixed all as specified & directed by Engr-in- charge.

S&F as 300mm ordinary rat tail rod pattern springs including roller and roller plate complete mild steel fixed complete all as specified and directed by Engr-in-Charge.

M&L Block board, 19/20mm thick, grade 1 quality, exterior grade, decorative type with decorative face veneer on both face, fixed with screws to timber frame work complete all as specified and directed by Engr-in-charge.

M&L plain fillets, square, rectangular or triangular in section, wrought, secured with nails or brads, sectional area exc 3 & n.exc 6 Sq.cm of 2nd class hard wood complete all as specified and directed by Engr-in-charge.

S&F continous (piano) hinges, mild steel, bright finish or electrogalvanised (width of flaps 30mm ) complete all as specified and directed by Engr-in-charge.

S&F 125mm hasp and staple, safety type, aluminium anodised with mild steel hinge pin including bolt to hinge plate and fixed with screws complete all as specified and directed by Engr-in-charge.

S&F 125 mm long aluminium anodised handle, cast type complete all as specified and directed by Engr-in-charge.

S&F stainless steel wire cloth 0.63 nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples complete all as specified and directed by Engr-in-charge.

,--ditto--- all per srl item No 77 above but fixed in repairs complete all as specified and directed by Engr-in-charge.

S&F 4mm thick sheet glass ordinary quality and glazing with aluminium beading in squares n. exc. 0.5 Sqm in each pane complete all as specified & directed by Engineer-in- charge.

S&F 4mm thick figured, pin head type and glazing with aluminium beading in squares n exc 0.5 Sqm in each pane complete all as specified & directed by Engineer-in- charge.

S&F 150 mm long floor door stopper of aluminium alloy body and tongue, anodised with hard drawn steel spring complete all as specified & directed by Engineer-in- charge.

M&L preparation of new or previously untreated wooden surface of any description not otherwise described over 10 cm width or girth and apply two coats of synthetic enamel paint over one coat of pink primer complete all as specified & directed by Engineer-in- charge.

M&L preparation of old painted wooden surface of any description not otherwise described over 10 cm width or girth and apply two coats of synthetic enamel paint complete all as specified & directed by Engineer-in- charge.

S&F drapery rods, coloured, standrad quality, powder coated not less than 25mm dia with heads at both ends and middle support, rings, etc. complete all as specified & directed by Engineer-in- charge.

S&F in repair brass hat pegs, solid body, 125 mm to 175 mm (4 legs) complete all as specified & directed by Engineer-in- charge.

S&F in repair towel rails 20mm dia 600mm long brass chromium plated superior quality brass chromium plated fancy type complete all as specified & directed by Engineer-in- charge.

S&F vitrieous china squatting Pan Orissa pattern size 580x440mm white with integral fort rests (excl flushing cistern) but including 'CI Trap' set and necessary fitting complete all as specified & directed by Engineer-in- charge.

S&F in repairs PVC valve less, syphonic action type flushing cistern,10 ltrs capacity low level, white, with inlet ball valve, float, handle and telescopic pipe and connection to pipe and flush pipe of polyethylene of low or high density or PVC, 32mm dia, for low level cistern complete all as specified & directed by Engineer-in- charge.

S&F in repair vitreous china wash hand basin coloured Flat back of size 550x400mm, long screwed shank fly nut flange end including cutting for and pinning in ends of brackets in 1:3 CM including 32mm dia chromium plated waste coupling/trap complete all as specified & directed by Engineer-in- charge.

S&F in repairs pillar tap, fancy type, cast copper alloy chromium plated with capston head, screwed down high pressure with or without lettered with long screwed shank and fly nuts, screwed for iron pipe of 15 mm bore complete all as specified & directed by Engineer-in- charge. Note : Wt not less than 450 gms

S&F in repair bib tap 15mm bore cast copper alloy chromium plated long body fancy type with capston head and cup screwed down, hand operated, screwed for iron pipe or for brass ferrule complete all as specified & directed by Engineer-in- charge. Note : Weight shall not be less than as given in SSR Part-I or relevant IS.

S&F in repair CP brass stop/angle valve fancy type 15 mm bore cast copper alloy screwed down high pressure fancy type with long shank and cup fixed complete all as specified & directed by Engineer-in- charge. Note : Weight shall not be less than as given in SSR Part-I or relevant IS.

S&F in repair CP brass stop valve fancy type 15 mm bore cast copper alloy screwed down high pressure fancy type with long shank and cup (Concealed type) fixed complete all as specified & directed by Engineer-in- charge. Note : Weight shall not be less than as given in SSR Part-I or relevant IS.

S&F in repair, shower rose, 125 mm size, brass chromium plated with sweivel joint complete all as specified & directed by Engineer-in- charge.

S&F PVC connections 15 mm size with PTMT nuts of length 450 mm complete all as specified & directed by Engineer-in- charge.

Dismentling of water tanks of capacity exc 500 and n.exc 1000 ltrs and removing from site complete all as specified & directed by Engineer-in- charge.

S&F rotational moulded polythene water storage tank 500 ltr capacity of tripple layer vertical with closed top hoisted and fixed in position all as specified in SSR part-I. All as directed.

S&F in repair gun metal globe or gate valve with iron wheel head, screwed both ends for iron pipe and fixed of 20mm bore fixed in repair all as specified and as approved by GE/Engineer-in-Charge.

S&F in repair ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed in 20mm dia bore pipe complete all as specified & directed by Engineer-in- charge.

Taking down 15 mm dia steel GI tubing including all connected fittings of any dia and in any position including cleaning for re fixing the serviceable pipe complete all as specified & directed by Engineer-in- charge.

,--ditto-- all as per srl item No 101 above but 20mm dia pipe complete all as specified & directed by Engineer-in- charge..

S&F 15 mm dia galvanised steel tubing medium grade including necessary fittings like sockets, tees, elbows, reducers, unions etc fixed to walls / ceiling complete all as specified & directed by Engineer-in- charge.

,--ditto-- all as per srl item No 103 above but 15mm dia pipe fixing only complete all as specified & directed by Engineer-in- charge. .

,--ditto-- all as per srl item No 103 above but 20mm dia pipe complete all as specified & directed by Engineer-in- charge..

,--ditto-- all as per srl item No 103 above but 20mm dia pipe fixing only complete all as specified & directed by Engineer-in- charge...

Dismantling of cast iron pipes, jointed in cement mortar and tabing out of trenches if required upto 100mm dia complete all as specified and as directed by engineer-in-Charge.

Dismantling of cast iron pipes, jointed in cement mortar and tabing out of trenches if required 75mm dia complete all as specified and as directed by engineer-in-Charge.

Supply & fixing 100 mm bore cast iron sand cast soil, waste and vent pipe in any length with or without ears fixed to wall with cement joints complete all as specified & directed by Engineer-in- charge.

Supply & fixing 75 mm bore cast iron sand cast soil, waste and vent pipe in any length with or without ears fixed to wall with cement joints complete all as specified & directed by Engineer-in- charge.

Fixing only 100 mm bore cast iron sand cast soil, waste and vent pipe in any length with or without ears fixed to wall with cement joints complete all as specified & directed by Engineer-in- charge.

Fixing only 75 mm bore cast iron sand cast soil, waste and vent pipe in any length with or without ears fixed to wall with cement joints complete all as specified & directed by Engineer-in- charge.

M&L in repairs 75mm dia cast iron floor trap with grating including jointing to waste pipe fixed in cement concrete (1:2:4) type B-1 using 20mm graded stone aggregate complete all as specified and directed by Engineer-in-Charge.

S&F in repairs branch pieces single (equal or unequal) ordinary or inverted (spring or socket type) or with paralled branch 100mm dia but with oval access door complete all as specified & directed by Engineer-in- charge..

S&F in repairs branch pieces single (equal or unequal) ordinary or inverted (spring or socket type) or with paralled branch 75mm dia but with oval access door complete all as specified & directed by Engineer-in- charge..

S&F in repairs 75mm cast iron sanitary connections-short connections pipe of length upto 300mm with socket fixed complete all as specified and directed by EIC.

S&F in repairs 100mm cast iron sanitary connections-short connections pipe of length upto 300mm with socket fixed complete all as specified and directed by EIC.

S&F in repairs 75mm bore cast iron bends (any radius) dimining pieces or tapers (larger bore measured) with oval access door fixed with cement joints complete all as specified and directed by Engineer-in-Charge

S&F in repairs 100mm bore cast iron bends (any radius) dimining pieces or tapers (larger bore measured) with oval access door fixed with cement joints complete all as specified and directed by Engineer-in-Charge

Taking down eaves gutters and rainwater pipes (any size or pattern) including all fittings, heads, shoes, bends, swan-necks etc., including cleaning or refixing or removal to Store (measured overalll as fixed along the cente line over fittings and accessories) complete all as specified & directed by Engineer-in- charge.

S&F 110 mm dia PVC SWR pipe, single socketed in any length with rubber ring joints fixed with clamps to wallscomplete all as specified & directed by Engineer-in- charge.

S&F 110 mm dia PVC (SWR) bend any radius complete all as specified & directed by Engineer-in- charge.

S&F in repairs 32 mm dia low density polyethylene pipes (LDPE) of pressure rating 6 kgf/cm2 fixed complete to walls, ceilings or in floors complete all as specified & directed by Engineer-in- charge.

S&F in repair sinks with drainage board made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 915 mm x 460 mm bowl size 410 mm x 330 mm x 160 mm complete all as specified & directed by Engineer-in- charge.

S&F stainless steel kitchen plate rack made with 1mm thick sheet of size 24" X 24" X 10" including taking down existing wooden plate rack complete all as specified & directed by Engineer-in- charge.

Dismantling asbestos cement (corrugated / semi corrugated) sheets including ridges as in roof covering all as specified & directed by Engineer-in-Charge.

S&F Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet including Ridge 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified & directed by Engineer-in-Charge.

Demolition of wall and Asbestos ceiling board or insulation boards/slabs/blankets, any thickness including cover fillets complete all as directed by Engineer-in-Charge.

S&F arm strong mineral fibre accoustical suspended ceiling system with ANF (Micro look) EGE tiles with arm strong silhouette exposed grid. The tiles should have humidity resistance (RH) of 90% NRC 0.5% Light reflectance shall be more than 85% thermal conductivity K=0.052 - 0.057 W/mk. Colour shall lbe white, fire performance class 0/class 1 (BS 476) in module size of 600mm x 600mm x 15mm with bioblock coating on the face of tiles. Suitable for green building application with recycle content of 63%. The tiles shall be laid on arm strong silhouette profile grid system with 15mm with flanges incorporating 6mm central revel in white / black colour and with a web height of 45mm and and load carrying capacity of minimum 15.68 kg/Sqm. Silhouette, main runner and cross runner shall have mitred end and birdsmouth notches to provides mitred juction. The Tee section have a galvanised of 125 gms/Sqm complete all as specified and directed by Engr-in-Charge.

M&L for machine cut kota stone slab flooring 20-25 mm thick laid over and including 15 mm thick screed bed in cement mortar 1:6, set and jointed with grey cement slurry mixed with pigment to match shade of the slab including rubbing and plishing complete all as directed.

M&L for machine cut kota stone slab 20-25 mm thick in riser of steps, skirting, dado and pillar laid over and including 10 mm thick backing coat in cement mortar 1:4 set and jointed in neat cement slurry mixed with pigment to match shade of the slab including rubbing and plishing complete all as directed by Engineer-in-Charge.

S&F Vitreous China Urinal, Half stall type, white (excluding flushing cistern, flush pipe and waste pipe) including conncetion to flushing pipe and waste pipe providing and fixing plugs bedding urinal against wall complete all as directed by Engineer-in-Charge.

Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm in Hard/dense soil complete all as directed by Engineer-in-Charge.

S&F Steel work in tubular / hollow section in trusses, rafter, purline, post etc. including special shaped washer, plate, cleat, etc. complete using ERW or induction butt welded tubes conforming to I. S.1161- 1979 grade St.-240 complete all as directed by Engineer-in-Charge.

S&F framed work with stainless steel material such as grills, gratings, etc., of ormamental and intricate design with ends of bars shouldered and/or riveted, or forged into spiles; framed guard bars; barred iron doors; ladders; framed balusteres; walk ways; railings; framework of water tanks and similar work conforming to Fe. 290, Gde-E-165 complete all as directed by Engineer-in-Charge.

Surface excavation N.exc. (not exceeding) 30 cm deep and averaging 15cm deep and getting out in soft/loose soil complete all as directed by Engineer-in-Charge.

M&L for 100mm thick PCC (1:4:8) type D2 using 40mm graded stone aggregate as in sub base below floors complete all as directed by Engineer-in-Charge.

Material and labour for rendering/plastering 15mm thick in cement mortar (1:4) on Fair faces of brick work/ concrete surfaces on walls finished fair and even and smooth without using extra cement complete all as specified and as directed by the Engineer-in-Charge.

M & L for reinforced cement concrete type B1 (1:2:4) 20mm graded stone aggregate in chajjas complete all as specified and directed by Engineer-in-charge

M&L for raking out joints / pointing to brick walls, complete all as specified and directed by Engineer-in-charge.

M&L for keyed pointing in cement mortar (1:3) to brick walls complete all as specified and directed by Engineer-in-charge.

Material and labour for 3mm thick wall care putty on wall surface in double coat complete all as specified and directed by Engineer-in-Charge. Note : colour shall be decided by Engr-in-charge.

M&L for applying two coats of oil bound distemper over a coat of chalk whiting primer on a prepared surface complete all as specified & directed by Engineer-in-Charge.

Material and labour for preparation of old painted steel surfaces of any description not otherwise described over 10cm width or girth & applying one coat of synthetic enamel paint (1st quality) of approved tint/colour to achieve glossing finish complete as specified and as directed by Engineer-in-Charge.

Supply & fixing 35mm thick flush shutters, solid core construction,with block board core and plywood face panels,commercial type kiln seasoned and chemically pressure treated complete all as specified & directed by Engineer-in- charge. Note : - (i) The sutters shall be brought at site without primer and same shall be applying at site as per direction of Engineer-in-charge. Primer shall be measured paid separately under appropriate item (painting) of BOQ.

Supply & fixing aluminium anodised barrel tower bolt of extruded section 300mm long complete all as specified & directed by Engineer-in-charge.

M & L for factory made steel windows conforming to IS-1038 with side hung shutters including box type hinges with 02 nos MS 100mm size barrel tower bolt for each leaf and Z section steel handle and steel peg stay complete with glazing bars, dovetailed or welded all as specified and directed by ingineer in charge.

M & L for factory made steel windows conforming to IS-1038 with side hung shutters including box type hinges with 02 nos MS 100mm size barrel tower bolt for each leaf and Z section handle and steel peg stay complete without glazing bars, dovetailed or welded all as specified and directed by ingineer in charge.

Material & Labour for mild steel work conforming to Fe-290 Gde E-165 as in grills, gratings etc. with ends of bars shouldered and/ or rivetted or forged into spikes; framed 12mm square guard bars, walkways, railing, framed work of water tanks and similar works complete all as directed by Engineer-in- charge

Forming jambs, etc. to openings (to foregoing item), including cutting, toothing and properly bonding into old work, also facing, jointing and pointing to match existing work, complete and new work built in CM 1:6, complete all as directed.

E/M PORTION Taking down carefully copper/aluminium point wiring (light, socket or power) complete (fittings such as switches, ceiling roses, pendants, regulators, sockets etc to be measured separately), and making good disturbed surfaces of walls, floors etc to match with existing surfaces complete all as specified and directed by Engr-in-Charge.

Taking down MCB with sheet metal enclosure, main switch, DB etc and making good disturbed surfaces to match with existing surfaces complete all as specified and directed by Engr-in-Charge.

Taking down sub main wiring of any size/capacity complete all as specified and making good disturbed surfaces to match with the existing surfaces complete all as specified and directed by Engr-in-Charge.

M&L for concealed Point wiring with two single core PVC insulate, unsheathed multistranded copper conductor cable of size 1.5 sq.mm (FRLS) drawn in and including electrical grade PVC conduit 20 mm dia concealed on wall/ceiling/floor including PVC insulated unsheathed earth wire with multi stranded copper conductor of size 1.5 sq.mm(FRLS) including MS shunk sheet metal box with modular sheet top cover of required module for mounting switches, sockets etc complete all as specified. Note - quoted rate shall include making good to the disturbed surfaces including plastering and painting to match with the existing colour for One Light point controlled by one, one way switch complete all as specified and directed by Engr-in-Charge. .

,--ditto--- all as per Serial item No 154 above, but for One ceiling/exhaust fan point controlled by one switch and regulator complete all as specified and directed by Engr-in-Charge.

,--ditto--- all as per Serial item No 154 above, but for One bell/buzzer point controlled by one bell push complete all as specified and directed by Engr-in-Charge.

,--ditto--- all as per Serial item No 154 above, but for One 3 pin 5 amps switch socket outlet point on same board with other switches complete all as specified and directed by Engr-in-Charge.

,--ditto--- all as per Serial item No 154 above, but for One 3 pin 5 amps switch socket outlet point on independent board complete all as specified and directed by Engr-in-Charge.

,--ditto--- all as per Serial item No 154 above, but for Two way point controlled by two, two way switch complete all as specified and directed by Engr-in-Charge.

,--ditto--- all as per Serial item No 154 above, but for wiring with 4 sq.mm multistranded cable and earth wire with copper conductor of size 4 sq.mm for 15 amps power point complete all as specified and directed by Engr-in-Charge.

Supply and fix piano switch flush button single pole one way 5/6 Amps complete all as specified and directed by Engineer-in-Charge.

Supply and fix piano switch flush button single pole two way 5/6 Amps complete all as specified and directed by Engineer-in-Charge.

Supply and fix bell push single pole 6 Amps complete all as specified and directed by Engineer-in-Charge.

Supply and fix socket outlet 2 in 1, 2/3 pin 6 amp flush type 250 volts AC complete all as specified and directed by Engineer-in-Charge.

Supply and fix socket outlet 2 in 1, 3 pin 5 amp and 15 amp flush type 240 volts AC complete all as specified and directed by Engineer-in-Charge.

Supply and fix piano switch 15/16 amp flush type 240 volts AC complete all as specified and directed by Engineer-in-Charge.

S & F batton integrated LED light fitting 1 x 20 W integral sleek polycarobonate LED Channel with white acrylic cover to roof/ceiling/wall with necessary wooden/PVC blocks etc and connecting with 2 core flexible PVC insulated multistranded copper conductor from ceiling rose to fitting incl taking out old one complete all as specified and directed by Engineer-in-Charge. Note : (i) With lumen efficiency in excess of 100 lumens par watt and driver efficiency>85% (with pf>0.95) (ii) CRI>80 (iii) The warranty of LED fittings is 02 year after completion of liability period

Supply and fix lamp holder insulated body with back plate for angle/batten fitting with LED of 09 watt complete all as specified and directed by Engr-in-Charge.

Supply and fix ceiling rose surface bakelite two to three terminals/plate 5 amps complete all as specified and directed by Engr-in-Charge.

Supply and fix Vertical MCB DB TPN 4 ways, 3 phase double door including MCCB 125 Amp 16 KA as incommer with bus bar rating 200 Amps vertical type dust and vermin proof including fixing on wooden board or recessed on wall complete all as specified and directed by Engr-in-Charge.

Supply and fix sheet metal enclosure DB single pole and neutral for 240 volts 8 way with 200 Amps rated busbar flush/surface mounting double door including wooden board complete all as specified and directed by Engr-in-Charge.

Supply and fix MCB single pole 240 volt 6-32 amps 10 KA, complete all as specified and directed by Engr-in-Charge.

Supply and fix MCB SPN 6-32 amp, 240 volt 10KA complete all as specified and directed by Engr-in-Charge.

Supply and fix MCB SP 32 amp, 240 volt 10KA complete all as specified and directed by Engr-in-Charge.

Supply and fixing PVC Blanking Plates one way with internal lock complete all as specified and directed by Engr-in-Charge.

Material & Labour for Sub Main Wiring with two run single core 10 Sqmm PVC insulated unsheathed (FRLS) cable with stranded copper conductor drawn in PVC conduit & accessories Suitable with and including 10 Sqmm copper green colour earth wire complete all as specified and directed by Engr-in-Charge. NOTE - Two run of 10 sq.mm & One run of 10 sq.mm & One run of PVC conduit with accessories shall be measured as One length.

S&F bulk head fitting in die cast aluminium housing and frosted glass complete all as specified and directed by Engr-in-Charge.

S&F miirror light fitting durable and weather proof industrial lighting solution luminaire with IP 65 protection complete all as specified and directed by Engr-in-Charge.

S&F MCB TP&N 63 Amp 240 volt 10 KA complete all as specified and directed by Engr-in-Charge.

S&F LED 2X2 flat panels to enhance the delight of occupants with fittings recess mounting complete all as specified and directed by Engr-in-Charge.

S & F stepped type fan regulator electronic solid state with stepssuitable for 1200/1400mm sweep ceiling fan working on 230V AC complete all as specified and directed by Engr-in-Charge. .

Material & Labour for Sub Main Wiring with two run single core 6 Sqmm PVC insulated unsheathed (FRLS) cable with stranded copper conductor drawn in PVC conduit & accessories Suitable with and including 6 Sqmm copper green colour earth wire complete all as specified and directed by Engr-in-Charge. NOTE - Two run of 6 sq.mm & One run of 6 sq.mm & One run of PVC conduit with accessories shall be measured as One length.

Note:- The contract sum shall be calculated by deducting the amount shown in Credit Schedule attached to this tender, from total amount of Schedule 'A'/BOQ

M/s Karan Builders

Dashmesh Construction Company