Loading
Loading…
Loading…
| # | Company | Quoted % | Amount | Rank | Status |
|---|---|---|---|---|---|
| 1 | L1₹17.0 LAdmitted-Finance A 5 293 II FLOOR PASCHIM VIHAR NEW DELHI DELHI 110063 | WEST DELHI | DELHI | 110063 | +4.44% | ₹17.0 L | L1 | Admitted-Finance |
| 2 | L2₹17.1 L+₹9,140.43 (0.54%)Admitted-Finance 24A LAJPAT NAGAR NEAR BUS STAND YAMUNA NAGAR | YAMUNANAGAR | HARYANA | 133103 | +5.00% | ₹17.1 L+₹9,140.43 (0.54%) | L2 | Admitted-Finance |
Tender Value
₹16.3 L
EMD Value
₹32,645
Closing Date
24 Aug 2026, 3:00 pmClosed
Executive Engineer
EE / HCD-2/DDA
Providing and installation of Open Gym Equipments with buy back of old equipment in Tikona Park and 1040 EWS Houses DDA Park. (Specialized Work).
2026_DDA_922454_1
16/EE / HCD-2/DDA/2026-27
Open Tender
Civil Works
Percentage
60 days
As Per NIT
Please refer Tender documents.
9 documents required · 9 mandatory
₹0
₹32,645
2 Sept 2026
18 Aug 2026
25 Aug 2026
18 Aug 2026
24 Aug 2026
18 Aug 2026
This is a percentage-rate BOQ. The schedule below shows estimated quantities and rates. Bidders quote a single percentage above or below the total estimated cost.
| Sl No | Description | Qty | Unit | Est. Rate | Est. Amount |
|---|---|---|---|---|---|
| 0SCHEDULE -A | |||||
| 1 | Providing and fixing "Air Walker" with the specifications below:
1. Dimensions (LxWxH): 1100 x 450 x 1300mm.
2. Fabricated with main post of NB 100mm (G.I.) "C" Class Pipe of approved make.
3. U-shaped main frame of NB 80mm (G.I.) "C" Class Pipe, Leg Support frame of NB 50mm (0.1) "C" Class Pipe.
4. Handy frame pipes of NB 32mm (G.I.) "C" Class (NB stands for Nominal Bore i.e., Internal Diameter of pipe in millimetres).
5. All pipes are powder-coated with 80–120-micron thick AkzoNobel or equivalent paints.
6. All joints of pipe are MIG welded with joints scalloped as necessary and dressed off removing sharp edges and burrs.
7. Zinc primer paint is applied at all the welding points prior to finishing.
8. Baseplate cover made of virgin LLDPE plastic by rotational molding with a minimum of 4.00mm thickness, UV resistant and coloured.
9. Foothold made of Co-Polymer Plastic with rounded edges to prevent impact and injury.
10. Maintenance-free bearings of SKF or equivalent make duly oil-sealed and self-lubricated are used in the equipment manufactured.
11. The equipment must be fitted with inbuilt limiters to prevent unwanted movements.
12. The equipment is to be fixed on the ground by providing and laying Cement Concrete with a minimum size of block to be constructed of 0.60 mtr x 0.60 mtr x 0.60 mtr (Payment for CC to be used in fixing of equipment shall be done separately) and J-shaped welded bolts of 18mm thickness.
13. High tensile steel with galvanized nut bolts is used for assembly.
14. Once the concrete is set, the equipment is fixed on to it and nuts and bolts are covered with a baseplate cover.
15. Equipment made to G5 Mark, EN16630, DIN 79000 & 150 14001 International standard for outdoor fitness equipment.
16. Self-Explanatory stainless-steel label fixed on equipment for ease of use, including maintenance cost for 2 years.
17. This rate is inclusive of GST Charges, Transportation Charges, Fixing Charges and CPOH. Nothing shall be paid extra. | 2 | each | 35,350 | ₹70,700 |
| 2 | Providing and fixing a double" Sit-Up Station" with the below specifications:
1. Dimensions (LxWxH): 1500 x 1150 x 650mm.
2. Fabricated with a main frame of NB 100mm (G.I.) "C" Class Pipe of approved make.
3. Main frame of NB 25mm (G.I.) "C" Class Pipe.
4. Leg support of NB 65mm (G.I.) "C" Class Pipe ('NB' stands for Nominal Bore i.e., Internal Diameter of pipe in millimetres).
5. Fixed on its top is back support made of perforated MS sheet of 2mm thickness.
6. All pipes are powder-coated using Akzo Nobel or equivalent paint of 80-120 micron thick.
7. All joints of pipe are MIG welded with joints scalloped as necessary and dressed off, removing sharp edges and burrs.
8. Zinc primer paint is applied at all welding points prior to finishing.
9. Baseplate cover made of virgin LLDPE plastic by rotational molding with 4.00mm thickness, UV resistant and coloured.
10. The equipment is to be fixed on the ground by providing and laying cement concrete with a minimum size of block to be constructed of 0.60 mtr x 0.60 mtr x 0.60 mtr (Payment for CC to be used in fixing of equipment shall be done separately) and J-shaped welded bolts of 18mm thickness.
11. Once the concrete is set, the equipment is fixed on to it.
12. High tensile steel with galvanized nut bolts is used for assembly.
13. Equipment made to EN16630 & DIN 79000 International standard for outdoor fitness equipment.
14. Self-Explanatory stainless-steel label fixed on equipment for ease of use, including maintenance cost for 2 years & maintenance cost for next 3 years @ 3% of the cost.
15. This rate is inclusive of GST Charges, Transportation Charges, Fixing Charges and CPOH. Nothing shall be paid extra. | 2 | each | 32,421 | ₹64,842 |
| 3 | Providing and fixing "Air Swing" in pair with the below specifications:
1. Dimensions (LxWxH): 1150 x 900 x 1250 mm.
2. Fabricated with main post of NB 100mm (G.I.) "C" Class Pipe of approved make.
3. Leg Support frame of NB 50mm (G.I.) "C" Class Pipe.
4. Handle support frame of NB 32mm (G.I.) "C" Class Pipe. ('NB' stands for Nominal Bore i.e., Internal Diameter of pipe in millimetres).
5. All pipes are powder-coated with 80–120-micron thick AkzoNobel or equivalent paints.
6. All joints of pipe are MIG welded with joints scalloped as necessary and dressed off, removing sharp edges and burrs.
7. Zinc primer paint is applied at all the welding points prior to finishing.
8. Handle bars are provided with high-end quality rubber grips.
9. Baseplate cover made of virgin LLDPE plastic by rotational molding with 4.00mm thickness, UV resistant and coloured.
10. Foothold made of MS Sheet Metal with rounded edges to prevent impact and injury.
11. Maintenance-free bearings of SKF or equivalent make duly oil-sealed and self-lubricated are used in the equipment manufactured.
12. The equipment must be fitted with inbuilt limiters to prevent unwanted movements.
13. The equipment is to be fixed on the ground by providing and laying Cement Concrete with a minimum size of block to be constructed of 0.60 mtr x 0.60 mtr x 0.60 mtr (Payment for CC to be used in fixing of equipment shall be done separately) and J-shaped welded bolts of 18mm thickness.
14. Once the concrete is set, the equipment is fixed on to it and the nuts and bolts are covered with a baseplate cover.
15. High tensile steel with galvanized nut bolts is used for assembly.
16. Equipment made to EN16630 & DIN 79000 International standard for outdoor fitness equipment.
17. Self-Explanatory stainless-steel label fixed on equipment for ease of use, including maintenance cost for 2 years.
18. This rate is inclusive of GST Charges, Transportation Charges, Fixing Charges and CPOH. Nothing shall be paid extra. | 2 | each | 45,288 | ₹90,576 |
| 4 | Providing and fixing "Horse Rider Station" with the specifications below:
1. Dimensions (LxWxH): 1000 x 600 x 1100 mm.
2. Fabricated with main post of NB 100mm (G.I.) "C" Class Pipe of approved make.
3. Main frame of NB 65mm (G.I.) "C" Class Pipe.
4. Handle support frame of NB 50mm (G.I.) "C" Class Pipe and other pipes of 4 NB 32mm & NB 25mm (G.I.) "C" Class Pipe. ('NB' stands for Nominal Bore i.e., Internal Diameter of pipe in millimetres).
5. All pipes are powder-coated with 80–120-micron thick AkzoNobel or equivalent paints.
6. All joints of pipe are MIG welded with joints scalloped as necessary and dressed off, removing sharp edges and burrs.
7. Zinc primer paint is applied at all the welding points prior to finishing.
8. Baseplate cover made of virgin LLDPE plastic by rotational molding with 4.00mm thickness, UV resistant and coloured.
9. Foothold made of NB 32mm (G.I.) "C" Class Pipe.
10. Seat to be made up from virgin LLDPE manufactured by rotational moulding with 4.00 mm thickness, coloured, UV resistant and environmentally friendly.
11. Maintenance-free bearings of SKF or equivalent make duly oil-sealed and self-lubricated are used in the equipment manufactured.
12. The equipment must be fitted with inbuilt limiters to prevent unwanted movements.
13. The equipment is to be fixed on the ground by providing and laying cement concrete with a minimum size of block to be constructed of 0.60 mtr x 0.60 mtr x 0.60 mtr (Payment for CC to be used in fixing of equipment shall be done separately) and J-shaped welded bolts of 18mm thickness.
14. Once the concrete is set, the equipment is fixed on to it and the nuts and bolts are covered with a baseplate cover.
15. High tensile steel with galvanized nut bolts is used for assembly.
16. Equipment made to EN16630 & DIN 79000 International standard for outdoor fitness equipment.
17. Self-Explanatory stainless-steel label fixed on equipment for ease of use, including maintenance cost for 2 years.
18. This rate is inclusive of GST Charges, Transportation Charges, Fixing Charges and CPOH. Nothing shall be paid extra. | 2 | each | 36,183 | ₹72,366 |
| 5 | Providing and fixing "Leg Press" in a pair with the below specifications:
1. Dimensions (LxWxH): 2000 x 550 x 1600 mm.
2. Fabricated with main post of NB 100mm (G.I.) "C" Class Pipe of approved make.
3. Seat Main frame of NB 50mm (G.I.) "C" Class Pipe and Pipe connecting main post to seat main frame of NB 65mm (G.I.) "C" Class Pipe. ('NB' stands for Nominal Bore i.e., Internal Diameter of pipe in millimetres).
4. All pipes are powder-coated with 80–120-micron thick AkzoNobel or equivalent paints.
5. All joints of pipe are MIG welded with joints scalloped as necessary and dressed off, removing sharp edges and burrs.
6. Zinc primer paint is applied at all the welding points prior to finishing.
7. Baseplate cover made of virgin LLDPE plastic by rotational molding of 4.00mm thickness, UV resistant and coloured.
8. Foothold is made of NB 50mm (G.I.) "C" Class Pipe.
9. Seats made up from virgin LLDPE manufactured by rotational molding with 4.00 mm thickness, are coloured, UV resistant and environmentally friendly.
10. Maintenance-free bearings of SKF or equivalent make duly oil-sealed and self-lubricated are used in the equipment manufactured.
11. The equipment must be fitted with inbuilt limiters to prevent unwanted movements.
12. The equipment is to be fixed on the ground by providing and laying cement concrete with a minimum size of block to be constructed of 0.60 mtr x 0.60 mtr x 0.60 mtr (Payment for CC to be used in fixing of equipment shall be done separately) and J-shaped welded bolts of 18mm thickness.
13. Once the concrete is set, the equipment is fixed on to it and the nuts and bolts are covered with a baseplate cover.
14. High tensile steel with galvanized nut bolts is used for assembly.
15. Equipment made to EN16630 & DIN 79000 International standard for outdoor fitness equipment.
16. Self-Explanatory stainless-steel label fixed on equipment for ease of use, including maintenance cost for 2 years.
17. This rate is inclusive of GST Charges, Transportation Charges, Fixing Charges and CPOH. Nothing shall be paid extra. | 2 | each | 49,238 | ₹98,476 |
| 6 | Providing and fixing "Pull Chair" in a pair with the below specifications:
1. Dimensions (LxWxH): 2400 x 800 x 2000 mm.
2. Fabricated with main post of NB 100mm (G.L.) "C" Class Pipe of approved make.
3. Seat main frame of NB 50mm (G.L.) "C" Class Pipe, Pipe connecting main post with handle frame of NB 65mm (GL) "C" Class Pipe.
4. Handle frame of NB 32mm (G.L.) "C" Class Pipe. ("NB" stands for Nominal Bore i.e., Internal Diameter of pipe in millimetres).
5. All pipes are powder-coated with 80–120-micron thick AkzoNobel or equivalent paints.
6. All joints of pipe are MIG welded with joints scalloped as necessary and dressed off, removing sharp edges and burrs.
7. Zinc primer paint is applied at all the welding points prior to finishing.
8. Handle bars are provided with high-end quality rubber grips.
9. Baseplate cover made of virgin LLDPE plastic by rotational molding with 4.00mm thickness, UV resistant and coloured.
10. Seat to be made up from virgin LLDPE manufactured by rotational molding with 4.00 mm thickness, coloured, UV resistant and environmentally friendly.
11. Maintenance-free bearings of SKF or equivalent make duly oil-sealed and self-lubricated are used in the equipment manufactured.
12. The equipment must be fitted with inbuilt limiters to prevent unwanted movements.
13. The equipment is to be fixed on the ground by providing and laying cement concrete with a minimum size of block to be constructed of 0.60 mtr x 0.60 mtr x 0.60 mtr (Payment for CC to be used in fixing of equipment shall be done separately) and J-shaped welded bolts of 18mm thickness.
14. Once the concrete is set, the equipment is fixed on to it and nuts and bolts are covered with a baseplate cover.
15. High tensile steel with galvanized nut bolts is used for assembly.
16. Equipment made to EN16630 & DIN 79000 International standard for outdoor fitness equipment.
17. Self-Explanatory stainless-steel label fixed on equipment for ease of use, including maintenance cost for 2 years.
18. This rate is inclusive of GST Charges, Transportation Charges, Fixing Charges and CPOH. Nothing shall be paid extra. | 2 | each | 59,085 | ₹1,18,170 |
| 7 | Providing and fixing "Seated Chest Press" in a pair with the below specifications:
1. Dimensions (LxWxH): 1800 x 700 x 2000 mm.
2. Fabricated with main post of NB 100mm (G.I.) "C" Class Pipe of approved make.
3. Seat Main frame of NB 50mm (G.I.) "C" Class Pipe.
4. Handle frame of NB 32mm and NB 25mm (G.I.) "C" Class Pipe.('NB' stands for Nominal Bore Size i.e., Internal Diameter of pipe in millimetres).
5. All pipes are powder-coated with 80–120-micron thick AkzoNobel or equivalent paints.
6. All joints of pipe are MIG welded with joints scalloped as necessary and dressed off, removing sharp edges and burrs.
7. Zinc primer paint is applied at all the welding points prior to finishing.
8. Handle bars are provided with high-end quality rubber grips.
9. Baseplate cover made of virgin LLDPE plastic by rotational molding with 4.00mm thickness, UV resistant and coloured.
10. Seat to be made up from virgin LLDPE manufactured by rotational molding with 4.00 mm thickness, coloured, UV resistant and environmentally friendly.
11. Maintenance-free bearings of SKF or equivalent make duly oil sealed and self-lubricated are used in the equipment manufactured.
12. The equipment must be fitted with inbuilt limiters to prevent unwanted movements.
13. The equipment is to be fixed on the ground by providing and laying cement concrete with a minimum size of block to be constructed of 0.60 mtr x 0.60 mtr x 0.60 mtr (Payment for CC to be used in fixing of equipment shall be done separately) and J-shaped welded bolts of 18mm thickness.
14. Once the concrete is set, the equipment is fixed on to it and nuts and bolts are covered with a baseplate cover.
15. High tensile steel with galvanized nut bolts is used for assembly.
16. Equipment made to EN16630 & DIN 79000 International standard for outdoor fitness equipment.
17. Self-Explanatory stainless-steel label fixed on equipment for ease of use, including maintenance cost for 2 years.
18. This rate is inclusive of GST Charges, Transportation Charges, Fixing Charges and CPOH. Nothing shall be paid extra. | 2 | each | 58,479 | ₹1,16,958 |
| 8 | Providing and fixing an "Arm Wheel" in a pair with the below specifications:
1. Dimensions (LxWxH): 850 x 800 x 1800 mm.
2. Fabricated with main post of NB 100mm (G.I.) "C" Class Pipe of approved make.
3. Wheel frame of NB 32mm with connecting spokes of NB 25mm, Pipe connecting main pilar with wheel frame of NB 50mm. All pipes must be (G.I.) "C" Class Pipes ('NB' stands for Nominal Bore Size, i.e., Internal Diameter of pipe in millimetres).
4. All pipes are powder-coated with 80–120-micron thick AkzoNobel or equivalent paints.
5. All joints of pipe are MIG welded with joints scalloped as necessary and dressed off, removing sharp edges and burrs.
6. Zinc primer paint is applied at all the welding points prior to finishing.
7. Baseplate cover made of virgin LLDPE plastic by rotational molding with 4.00mm thickness, UV resistant and coloured.
8. Maintenance-free bearings of SKF or equivalent make duly oil-sealed and self-lubricated are used in the equipment manufactured.
9. The equipment is to be fixed on the ground by providing and laying Cement Concrete with a minimum size of block to be constructed of 0.60 mtr x 0.60 mtr x 0.60 mtr (Payment for CC to be used in fixing of equipment shall be done separately) and J shaped welded bolts of 18mm thickness.
10. Once the concrete is set, the equipment is fixed on to it and nuts and bolts are covered with a baseplate cover.
11. High tensile steel with galvanized nut bolts is used for assembly.
12. Equipment made to EN16630 & DIN 79000 International standard for outdoor fitness equipment.
13. Self-Explanatory stainless-steel label fixed on equipment for ease of use, including maintenance cost for 2 years.
14. This rate is inclusive of GST Charges, Transportation Charges, Fixing Charges and CPOH. Nothing shall be paid extra. | 2 | each | 41,713 | ₹83,426 |
| 9 | Providing and fixing an "Elliptical exerciser" with the below specifications:
1. Dimensions (LxWxH): 1200 x 550 x 1600 mm.
2. Fabricated with main post of NB 100mm (G.I.) "C" Class Pipe of approved make.
3. Main frame of NB 80mm (G.I.) "C" Class Pipe.
4. Handle frame of N8 32mm and NB 25mm (G.I.) "C" Class Pipe. ('NB' stands for Nominal Bore Size i.e., Internal Diameter of pipe in millimetres).
5. All pipes are powder-coated with 80–120-micron thick AkzoNobel or equivalent paints.
6. All joints of pipe are MIG welded with joints scalloped as necessary and dressed off, removing sharp edges and burrs.
7. Zinc primer paint is applied at all the welding points prior to finishing.
8. Handle bars are provided with high-end quality rubber grips.
9. Baseplate cover made of virgin LLDPE plastic by rotational molding with 4.00mm thickness, UV resistant and coloured.
10. Maintenance-free bearings of SKF or equivalent make duly oil-sealed and self-lubricated are used in the equipment manufactured.
11. The equipment is to be fixed on the ground by providing and laying cement concrete with a minimum size of block to be constructed of 0.60 mtr x 0.60 mtr x 0.60 mtr (Payment for CC to be used in fixing of equipment shall be done separately) and J-shaped welded bolts of 18mm thickness.
12. Once the concrete is set, the equipment is fixed on to it and nuts and bolts are covered with a baseplate cover.
13. High tensile steel with galvanized nut bolts is used for assembly.
14. Equipment made to EN16630 & DIN 79000 International standard for outdoor fitness equipment.
15. Self-Explanatory stainless-steel label fixed on equipment for ease of use.
16. Foothold made of Co-Polymer Plastic with rounded edges to prevent impact and injury, including maintenance cost for 2 years.
17. This rate is inclusive of GST Charges, Transportation Charges, Fixing Charges and CPOH. Nothing shall be paid extra. | 2 | each | 45,288 | ₹90,576 |
stage.html
html • 0.03 MB
tech_eval.pdf
boq_comp_chart.xlsx
xlsx
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Tendernotice_1.pdf
PDF • 1.82 MB
NIT16.pdf
Tender Documents • 2.73 MB
BOQ_969427.xls
BOQ • 0.43 MB
corrrr.pdf
PDF • 0.30 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .