REPAIR AND MAINT OF TILING, FOORING, ROOF, CEILING, PLUMBING, SANITARY FITTINGS, JOINERY, PANELLING, STONE MASONRY ETC AT KHUNMOH GRN UNDER GE 861 EWS

Amount

Taking down cement plaster from brick or concrete or stone surfaces including raking out joints, hacking for key, scrubbing down with water etc, complete all as specified and directed.

Demolition of brick work or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars, etc. but excluding ashlar facings, dressed stonework and precast concrete articles, complete all as specified and directed.

Demolition of cement concrete (unreinforced) as in ground floors and pavings not exc 15cm thick below or above ground level, complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and removing serviceable materials to store and rubbish off the premises, complete all as specified and directed.

Demolition of reinforced cement concrete (reinforcement cut as required to facilitate) in any description and any position, complete all as specified and directed by the Engineer-in- Charge.

Taking down chowkat or frame with shutter (without taking off shutter from the frame) not exc 1.5 Sqm each including cutting holes for taking out hold fast and making good disturbed surface with existing surface, complete all as specified and directed.

Taking down chowkat or frame with shutter (without taking off shutter from the frame) exc 1.5 Sqm but not exc 4.0 Sqm each including cutting holes for taking out hold fast and making good disturbed surface with existing surface, complete all as specified and directed.

Taking down shutter of any description not exc 1.0 Sqm each, complete all as specified and directed.

Taking down shutter of any description exc 1.0 Sqm but not exc 2.00 Sqm each, complete all as specified and directed.

M&L for brick work with sub class "B" bricks (old size) straight or curved on plan exceeding 6 metre mean radius built in cement mortar 1:4, complete all as specified and directed by Engr-in-charge.

All as per Ser item No 10.00 above but except bricks

M&L for flush pointing to random rubble masonry, uncoursed or brought upto courses in CM 1:3, complete all as specified and directed.

M&L for rendering 15mm thick in CM 1:6 on other than fair faces brick work or concrete surfaces, finished the surface even and smooth without using extra cement, complete all as specified and directed.

M&L for rendering 10mm thick in CM 1:4 on fair faces of brick work or concrete surfaces, finished the surface even and fair without using extra cement, complete all as specified and directed.

M&L for rendering 5mm thick in CM 1:3 on fair faces of brick work or concrete surfaces as on ceiling, finished the surface even and fair without using extra cement, complete all as specified and directed.

M&L for RCC 1:1.5:3 M-20 grade (using 20mm graded crushed stone aggregate) as in slabs supported on walls, beams and columns in floors etc and the like, complete all as specified and directed.

Formwork to rough finished concrete surfaces of soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work, not exceeding 200mm thick (Horizontal or sloping), complete all as specified and directed by Engr-in-charge.

M&L for TMT mild steel bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and directed by Engr-in-charge.

M&L for precast cement concrete 1:2:4 type B-1 (using 20mm graded crushed stone aggregate) as in landings, cover slabs (for man holes/ septic tanks etc) and similar articles with plain faces, set in CM 1:4, complete all as specified and directed.

M&L for 25mm thick PCC 1:2:4 type B-0 (using 12.5mm graded crushed stone aggregate) as in floor to receive floor finishes, complete all as specified and directed.

M&L for vitrified ceramic dark shade coloured tiles, 10mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 Sqm as in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile, laid over and incuding 15mm thick screed bed or bedding layer in CM 1:4, complete all as specified and directed.

M&L for 10mm thick vitrified ceramic coloured tiles (Granite /Marble /wood textures), fixed on vertical surfaces over and including 10mm thick plaster in CM 1:4 for receiving tiles, set and jointed in neat cement slurry and pointed in white or colored cement to match the shade of tiles, complete all as specified and directed.

M&L for non skid coloured ceramic joint free tiles of size 400mm X 400mm X 7-8mm thick, as in floors etc, set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tile, laid/ fixed over and including 15mm thick sceerd bed or bedding layer in CM 1:4, complete all as specified and directed.

M&L for non skid coloured ceramic joint free tiles of size 300mm X 300mm X 7-8mm thick, as in floors etc, set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tile, laid/ fixed over and including 15mm thick sceerd bed or bedding layer in CM 1:4, complete all as specified and directed.

M&L for glazed ceramic coloured joint free tiles of size 300mm X 200mm X 7mm thick as on vertical surfaces, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile, fixed over and including 15mm thick plaster in CM 1:4, complete all as specified and directed.

M&L for glazed ceramic coloured joint free tiles of size 350mm X 250mm X 7mm thick or 450mm X 350mm X 7mm as on vertical surfaces, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile, fixed over and including 15mm thick plaster in CM 1:4, complete all as specified and directed.

Demolition of stone slabs and tiles of any description or thickness in floors, aprons etc, complete all as specified and directed.

M&L for 18-20mm thick machine cut kota stone slab flooring, jointing with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing, laid over and incuding 20mm thick screed bed in CM 1:4, complete all as specified and directed.

All as per Ser item No 28.00 above but on vertical surfaces such as walls/ skirtings/ dados etc, complete all as specified and directed.

M&L for granite (of any type) tiles, 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing, laid over and including 15mm thick screed bed in CM 1:4, complete all as specified and directed.

M&L for 75mm thick PCC 1:4:8 type D-2 (using 40mm graded crushed stone aggregates) as in sub base of floor, finished the surface fair and even without using extra cement, complete all as specified and directed.

M&L for chequered cement concrete tiles of size 20cm x 20cm x 25mm thick as in floors, set, jointed and pointed in neat cement slurry and pointed with grey cement and pigment, laid over and including 15mm thick screed bed or bedding layer in cement mortar 1:4, complete all as specified and directed.

M&L for 2nd class hard wood plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, supplied and fixed at site, complete all as specified and directed.

S&F 35mm thick 2nd class hard wood plain framed paneled shutters (any no. of panels) with panels of timber flat on both sides (feathered edge) or veneered particle board with commercial face venners supplied and fitted to chowkats at site, complete all as specified and directed.

S&F 35mm thick 2nd class hard wood glazed & skeleton shutters for door, open rebated and prepared to receive glass, gauge etc. (with sash bars) edges of framing plain, chamfered or rounded , fitted with cuts and mitred beads for securing glass etc, sizes of members of shutters as specified in SSR Part- I Section -8 Clause 8.23 (a), complete all as specified and directed.

S&F 30mm thick 2nd class hard wood glazed & skeleton shutters for windows/ ventilators, open rebated and prepared to receive glass, gauge etc, divided into square with plain, chamfered or rounded , mitred and rebated sash bars any numbers, provided with stiles and rails as specified in SSR Part- I Section-8 Clause 8.24 (b), complete all as specified and directed.

S&F solid PVC door frame of size 50x47mm made out of 5mm thick plain colour PVC sheet reinforced with MS Square tube, suppling & fixing in opening as per specification & drawing.

S&F 30mm thick factory made solid panel PVC door shutter (style) consisting of frame made out of MS tubes for top & bottom rails, MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing

S&F aluminium door of extruded aluminium section, consisting of frame vertical and horizontal, members of size 100mmx45mmx2.5mm thick with shutter stile 85mmx45mmx2.50mm thick, top, middle and bottom rail of size 101.60mmx44.5mm with 5.50mm thick tinted sheet glass and 10-12mm thick PVC prelaminated particle board with aluminium beading and rubber gasket/ beading including fixing of hydraulic floor spring one in single leaf or two Nos in double leaf door. One mortise lock for aluminium door (each) and two Nos 200 mm long aluminium tower bolts and two Nos aluminium handles 'D' type for each door. Fixing with rawl plug including rectification of floor/ wall to match with existing surfaces, complete all as specified and directed by Engr-in-Charge.

S&F aluminium fully glazed window openable shutter with aluminium section , consisting of frame vertical and horizontal members of size 100mmx44.45mmx1.90 mm thick for frame and section for shutter 45mmx44.5mmx1.9mm thick with 5.50mm thick tinted sheet glass with aluminium beading and rubber gasket/ beading clips, 3 Nos, 150mm long handle 02 Nos 'D' type, 75mm long aluminium butt hinges min 02 Nos in each leaf fixing with rawl plug including rectification of jambs floor/wall to match with existing surfaces, complete all as specified and directed by Engr-in-Charge.

S&F aluminium partition with aluminium anodised tube of section 114mm x44.5mm x1.5mm thick at bottom and remaining vertical and horizontal rail of section 44.5mm x45mm x 2mm thick, aluminium clip rubber beading aluminium angle, nut, bolts etc (from bottom 75cm height both side PVC prelaminated board 10 to 12mm thick ISI marked and remaining parts of partition be covered with glass 5.5mm thick, spacing of glazed aluminium tube in horizontal 75cm (max) and vertical 90cm (maximum), complete all as specified and directed.

S&F 300mm long aluminium alloy anodised sliding door bolt with hasp and stapple (bolt type) and fixing clips of sheet cast or extruded section with fixing bolts and sliding bolt of extruded section, complete all as specified and directed.

S&F aluminium anodised, barrel tower bolt of extruded section, 200mm length of bolt, complete all as specified and directed.

S&F in reapir aluminium anodised, barrel tower bolt of extruded section, 200mm length of bolt, complete all as specified and directed.

S&F aluminium anodised, barrel tower bolt of extruded section, 150mm length of bolt, complete all as specified and directed.

S&F in repair aluminium anodised, barrel tower bolt of extruded section, 150mm length of bolt, complete all as specified and directed.

S&F aluminium anodised handle, extruded fabricated type of size 150mm, complete all as specified and directed.

S&F in repair aluminium anodised handle, extruded fabricated type section of size 150mm, complete all as specified and directed.

S&F aluminium anodised handle, extruded fabricated type section of size 100mm, complete all as specified and directed.

S&F in repair aluminium anodised handle, extruded fabricated type section of size 100mm, complete all as specified and directed.

S&F butt hinges medium weight, cold rolled mild steel, size 100mm, complete all as specified and directed.

S&F in repair butt hinges medium weight, cold rolled mild steel, size 100mm, complete all as specified and directed.

S&F butt hinges medium weight, cold rolled mild steel, size 75mm, complete all as specified and directed.

S&F in repair butt hinges medium weight, cold rolled mild steel, size 75mm, complete all as specified and directed.

S&F MS 300mm size, ordinary rat tail rod pattern springs, including roller and roller plate, complete all as specified and directed.

S&F in repair MS 300mm size, ordinary rat tail rod pattern springs, including roller and roller plate, complete all as specified and directed.

S&F floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor, of size 150mm, complete all as specified and directed.

S&F in repair floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor, of size 150mm, complete all as specified and directed.

Hacking out old broken glass (any thickness, size, quality or description) from wooden/ metal frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads, complete all as specified and directed.

S&F 4.0mm thick sheet glass, ordinary quality and glazing with oil putty or beads/ glazing pins in square not exc 0.50 Sqm in each pane, complete all as specified and directed.

S&F 4mm thick figured glass, pin head type and glazing with oil putty or beads/ glazing pins in squares not exc 0.50 Sqm in each pane, complete all as specified and directed.

S&F galvanised MS wire cloth 0.56mm nominal dia of wire and average width of aperture 1.18mm, fixed with tinned tacks or galvanised wire staples, complete all as specified and directed.

S&F in repair galvanised MS wire cloth 0.56mm nominal dia of wire and average width of aperture 1.18mm, fixed with tinned tacks or galvanised wire staples, complete all as specified and directed.

Dismantling water tank of any description, exc 500 liters but not exc 1000 litres capacity and removing from site, complete all as specified and directed.

S&F 500 Ltrs capacity rotational moulded polyethylene water storage tank, cylindrical vertical with closed top, hoisted and fixed in position, connecting to inlet and outlet pipe connections with and including ball brass valve, high pressure with polythene float and flynut, screwed for iron pipe or brass ferrule of 20mm bore pipe, complete all as specified and directed.

S&F in repair vitreous china squatting pan, orissa pattern of size 580mm x 440mm with integral foot rests, white and connecting to drain pipe/ trap and including provision of cement concrete and making good to floor match with existing floor, complete all as specified and directed.

S&F vitreous China bowl urinal, flat back of size 465mm x 355mm x 265mm, white with grating and union for discharge pipe including flushing system, flush pipe and waste pipe, complete all as specified and directed.

S&F grating doom 125mm dia with waste hole of PTMT (Minimum weight 40gms), complete all as specified and directed.

S&F in repair PVC valveless 10 litres capacity, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets, complete all as specified and directed.

S&F in repair vitreous china wash hand basin, white, flat back of size 550x400mm including brackets & including cutting for and pinning in ends of brackets and waste coupling of PTMT of suitable size (half or full threaded) (Minimum weight 32mm- 45gms/40mm-60 gms), 32mm dia flush pipe of polyethylene of low or high density or PVC and 15mm bore CP pillar tap, complete all as specified and directed.

S&F in repair 15mm size PVC connection with PTMT nuts, length 600mm long, complete all as specified and directed.

S&F in repair 15mm size PVC connection with PTMT nuts, length 450mm long, complete all as specified and directed.

S&F in repair swivel shower of PTMT of any colour for fixing with 15mm dia pipe and shower arm 15 mm size, 195mm long with bend of 45 degree with flange of PTMT of any colour (Minimum weight 40gms), complete all as specified and directed.

S&F 100mm size cast iron sanitary connection for WC, complete all as specified and directed.

S&F in repair/ replacement cast iron 75mm bore soil, waste and vent spun pipe of any length with or without ears, with cement joints, laid in trenches or in floor etc, complete all as specified and directed.

S&F in repair/ replacement cast iron 100mm bore soil, waste and vent spun pipe of any length with or without ears, with cement joints, laid in trenches or in floor etc, complete all as specified and directed.

S&F in repair/ replacement 75mm dia CI floor trap, with grating including jointing to waste pipe, fixed in cement concrete 1:2:4 type B1, complete all as specified and directed.

S&F in repair/ replacement cast iron Nahani trap 75mm dia including jointing to pipe, complete all as specified and directed.

S&F in repair/ replacement 75mm bore CI bends (any radius) diminishing pieces or tapers, complete all as specified and directed.

S&F in repair/ replacement 100mm bore cast iron vent cowl, complete all as specified and directed.

S&F in replacement 15mm bore CP fancy type, bib tap, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed.

S&F in replacement 15mm bore stop valve/ angle valve, cast copper alloy, screwed down, high pressure with crutch or butterfy handle, screwed for iron pipe and fixed, complete all as specified and directed.

S&F in replacement 15mm bore CP stop/angle valve with long shank and cup (concealed type) cast copper alloy, screwed down, high pressure fancy type, complete all as specified and directed.

Taking up or down 15mm bore GI water tubing and connections, including cleaning for refixing or removal to store, complete all as specified and directed.

Taking up or down 20mm bore GI water tubing and connections, including cleaning for refixing or removal to store, complete all as specified and directed.

S&F 15mm bore GI water tube, medium grade with all fittings and fixtures complete to walls and ceiling or laid in floors, complete all as specified and directed.

S&F 20mm bore GI water tube, medium grade with all fittings and fixtures complete to walls and ceiling or laid in floors, complete all as specified and directed.

Fixing only 15mm bore GI water tube, medium grade with all fittings and fixtures complete to walls and ceiling or laid in floors, complete all as specified and directed.

Fixing only 20mm bore GI water tube, medium grade with all fittings and fixtures complete to walls and ceiling or laid in floors, complete all as specified and directed.

S&F in replacement towel rail 600mm long of aluminium anodised, fixed with & including chromium plated brass screws, complete all as specified and directed.

S&F in repair vitreous china wash down water closet pan (pedestal pattern) white, complete including ‘P’ or ‘S’ trap, seat cover and fixed to flushing cistern, brackets, flushing pipe etc, complete all as specified and directed.

S&F in replacement 15mm bore brass CP mixer for mixing hot and cold water, screwed down, high pressure with long screwed shank and fly nuts, screwed for iron pipe, complete all as specified and directed.

S&F in replacement health faucet CP Brass, hand Jet shower 15mm bore dia and 1500mm long CP pipe, complete all as specified and directed.

S&F in replacement 15mm bore pillar tap, cast copper alloy with capstan head, chromium plated, screwed down, high pressure, screwed for iron pipe and fixed, complete all as specified and directed.

S&F in replacement 15mm bore, bib tap standard of PTMT of any colour, high pressure, screwed for iron pipe and fixed (Minimum weight 90gms).

S&F in replacement 20mm bore gun metal, globe or gate valve, with iron wheel head, screwed both ends for iron pipe and fixed.

S&F in repair/ replacement 75mm bore PVC (SWR) pipe, single socketed in any length with rubber ring joints, laid in floor or trenches or fixed to walls with suitable clamps, complete all as specified and directed.

S&F in repair 100mm bore PVC (SWR) pipe, single socketed in any length with rubber ring joints, laid in floor or trenches or fixed to walls with suitable clamps, complete all as specified and directed.

S&F 75mm bore PVC (SWR) bends of any radius, complete all as specified and directed.

S&F 110mm bore PVC (SWR) bends of any radius, complete all as specified and directed.

S&F 110mm bore PVC (SWR) vent cowl, complete all as specified and directed.

S&F 75mm bore PVC (SWR) vent cowl, complete all as specified and directed.

Dismantling wall and ceiling boards (fiber, pulp, insulation, etc) or insulation boards/slabs including cover fillets etc, complete all as specified and directed.

S&F anodised aluminium snap grid of size 605mmx605mm frame work for false ceiling including straining with GI wire 4mm dia, complete all as specified and directed.

S&F 10mm thick PVC insulation panels with EPS stuck to 1mm thick plain PVC sheet suitably placed in false ceiling grid made of aluminum GI/MS as per specification and manufacturer's instructions.

S&F solid PVC wall paneling decorative type consisting of 5mm thick plain colour PVC pre-laminated sheet inclusive of solvent cement and and fixing at site on PVC frame, complete all as specified and directed.

S&F 5mm thick PVC sheet fillets of width 35mm for wall paneling inclusive of fixing on to wall to make PVC frame, complete all as specified and directed.

S&F 9mm thick veneered decorative plywood, grade 1 (with BWR resin) with decorative face veneers on one faces, fixed with screw to timber frame work as on wall and ceiling, complete all as specified and directed.

S&F in repair weather boarding in 2nd class hardwood, clean sawn plain, 20mm thick or feather edges, 15mm to 20mm thick and fixed with 30mm laps joints, complete all as specified and directed.

M&L for 2nd class hardwood as in frame, scantlings etc, in any position including dismanting and taking down existing timber, complete all as specified and directed.

Dismantling plain or corrugated steel sheeting any gauge, thickness including Nainital or similar pattern roof coverings, complete all as specified and directed.

S&F 0.50mm thick pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet of an colour having tensile strength of 550 Mps as in roof covering /cladding to wall, fixed with self tapping screws, compete all as specified and directed.

S&F 0.50mm thick pre-painted galvalume aluminium zinc coating GI based plain steel sheet of an colour having tensile strength of 550 Mps as in roof covering /cladding to wall, fixed with self tapping screws, compete all as specified and directed.

S&F 0.63mm thick galvanised, corrugated mild steel sheeting with two corrugation side lap, fixed with coach screws and washers in roof etc. with grade of zinc coating 275, complete all as specified and directed.

S&F 0.63mm thick plain galvanised mild steel sheeting in ridges, hips, valley, gutters, drip and straight flashings (length and girth as fixed) with grade of zinc coating 275, complete all as specified and directed.

M&L for preparation of newly plastered or unplastered surface of walls and applying two coats of cement base paint over a coat of alkali resistant primer, complete all as specified and directed.

M&L for preparation of newly plastered surfaces of walls and applying two coats of oil bound distemper over a coat of primer over and including 2mm thick wall care putty to receive smooth surface, complete all as specified and directed.

M&L for preparation of newly plastered surfaces of ceiling and applying three coats of white wash, complete all as specified and directed.

M&L for preparation of old surfaces of walls after removing of existing treatment and applying two coats of cement base paint, complete all as specified and directed.

M&L for preparation after removing existing treatment of surfaces of walls and applying two coats of oil bound distemper over and including applying 2-3mm thick wall care putty to receive smooth surface, complete all as specified and directed.

M&L for preparation of old surfaces of ceiling and applying two coats of white wash, complete all as specified and directed.

M&L for preparation of new wooden surfaces or articles of any description over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer, complete all as specified and directed.

M&L preparation of new steel or iron surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer, complete all as specified and directed.

M&L for preparation of old painted wooden surfaces of any description over 10cm width or girth and applying two coat of synthetic enamel paint, complete all as specified and directed.

M&L for preparation of old painted steel and iron surfaces of any description over 10cm width or girth and applying two coat of synthetic enamel paint, complete all as specified and directed.

Suppy and insert glass dividing strips, 3mm thick in floors, complete all as specified and directed.

M&L for 100mm thick PCC 1:2:4, type B-2 (using 40mm graded crushed stone aggregate) as in sub base or floors, laid in alternate bays and joint with mastic filling compound, finished the surface even and smooth without using extra cement, complete all as specified and directed.

M&L for 75mm thick PCC 1:3:6 type C-2 (using 40mm graded crushed stone aggregates) as in pavement/ plinth protection, laid in alternate bays and joints shall be filled with bitumastic filler with 80/ 25 bitumen, finished the surface fair and even, complete all as specified and directed.

S&F in replacement ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for 15mm bore iron pipe and fixed. (Minimum weight 142gms), complete all as specified and directed.

S&F in replacement 25mm dia harrison rails/ curtain rod, mild steel, chromium plated decorative type with 2 Nos wood finished side brackets, knobs, complete all as specified and directed.