REPAIR, REPLACEMENT OF JOINERY, ALUMINIUM DOOR, ALUMINIUM WINDOW AND ALUMINIUM PARTITION, FALSE CEILING, FLOOR TIILES AND WALL TILES ETC IN CERTAIN BUILDING INSIDE TECHNICAL AREA DMSRDE, KANPUR

Amount

Taking down wooden cupboard / Aluminium partition wall any description not exceeding 1 Sqm each panel complete all as speceifed and directed of frames with shutters (with out taking off shutters from the frame) area etc 1.5 Sqm but not etc 4.00 Sqm each.

M&L for fully glazed cupboard with openable shutter having powder coated aluminium section of size 50 x 44.45 x 2mm thick for frame and section for shutter 40 x 25 x 1.5mm thick 4.8mm thick plain/figured glass sheet with necessary jointing cleats, glazing clips, rubber packing, aluminium and rubber beading, mortice lock of brass of size 65mm,vertical type four levers, aluminiumhinges of size 75mm, 125mm long aluminium handle fabricated type including proper fixing of aluminium frame with screw and PVC gully of adequate size as per requrement of site complete all as specified and directed (Note Colour of powder coating and glass will be approved By GE(I)

M&L for 15 micron natural colour having powder coated aluminium section partations partily glazed partily paralled area of each panel not exceeding one sqm with section38mmx63.5mmx1.50mm including necessary joints cleats, glazed clips rumber packing screw 4.8mm thick plain/tinted glass two numbers upper panel and 12mm thich prelaminated particle board BWA type molamine finish (both side) on bottom panel (0.80mmheight) including necessary fittings etc complete all as specified and directed.(Colour of glass shall be approved by GE(I) R&D Kanpur

Taking down chowkhets of frames (wooden / aluminium) with shutters(with out taking off shutters from the frame) area etc 1.5 Sqm but not etc 4.00 Sqm each

M&L for 15 micron natural coloured having powder coated aluminium section door frame 101.60 mm x 44.50 mm x 3.0 mm with top rail 100.60 mm x 44.45 mm x 2.9 mm bottom and lock rail 150 mm x 44.45 mm x 2.9 mm and stiles 85mm x 44.45 mm x 2.9 mm including aluminium snap beading of size 19.05 mm x 17.27 mm necessary jointing cleats, glazing clips, rubber packing, screw and 4.8mm thick plain/figured glass on panels including necessary fittings such as round type handle 125 mm size including floor spring (ISI mark) locking arrangement (mortice lock), 03 hinges of size 125mm aluminium anodised medium grade in each complete all as specified and directed.(Colour of glass shall be approved by GE(I) R&D Kanpur.

S & F in repair door closer hydraulically regulated (aluminium dia cast) designation No. 3 universal type sutable for door shutter of 851 to 1000mm width and of wt between 35 to 80 Kg complete all as specified and directed.

Dismantling of ceiling boards and wall (fibre, insulation, etc or perforates/ insulation boards) any thickness, including cover fillets etc complete all as specified and directed

S&F Anodised aluminium snap grid 605x606 mm frame work of angle 25mmx25mmx1.5mmmm and Main Tee 38mmx26mmx1.5mm for false ceiling complete all as specified and directed.

M&L for providing and fixing of 9mm thick PVC laminated Gypsum board inceiling fixed with srews as per manufacturer instructions for any height up to and including complete all as specified and directed.

S&F Hangers 4 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I.flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified

M&L for paradise vertical blinds standards 100mm width made of cotton fabric with following accessories as mentioned below: (a) HEADRAIL: Extruded anodised high strength aluminium alloy section with wall thickness of 1.2mm . (b) CONTROL UNIT: Made of derlin (Celon), it consists of tilting control which rotates the louvers and the traverse cord moves on pulleys in the control unit for stacking. (c) CARRIERS: Moulded of derlin (Celon) with an anti-friction additive. It consists of a housing with wheels, upper bevel gear matching lower gear,louver holding stem with a hanger book and keeper to match the hole in the top of the louver. (d) TILTER : Nickle plated brass/steel ball chain. It tilts the louver to any desired angle upto 180o and holds them at that angle. (e) TRAVERSE CORD: Braided of high strength polyster fibre, It is flexible, has minimum stretch and maximum abrasion resistance. (f) TILT ROD: Extruded hard aluminium alloy with three/four equally spaced keyways for operation of carrier gear. (h) INSTALLATION BRACKET: Made from galvanised steel of 10 gauge fitted with pressure clips made of spring steel to hold the headrail. (j) BOTTOM MECHANISM : (i) Bottom Weight made from galvanised steel sheets and is powder coated for maximum corrosion resistance. It is inserted in the louver to keep it straight. (ii) Bottom chain of brass/steel nickle plated of 2 mm with equally spaced 'clear clips' fitted on it, It is attached to bottom weight, to maintain the louver spacing. (i FABRICS LOUVERS: Fabric woven from polyster fibres.Protective coating and fusion with chemicals is done for stain resistance and soil repellancy. (k) Fabric colour, EI 2124 and EC 1110 or any other colour as approved by GE(I).

Taking down cement plaster / dado from brick wall or concerete surface including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

M&L Rendering 15mm thick in cm 1:6 on fair faces of brick work or concrete surfaces finish even and fair with out using extra cement complete all as specified and directed.

M&L for preparation of old plastered surfaces of walls including cornices plaster etc by complete removal of existing treatment and applying two coat oil bound distemper complete all as specified and directed.

M&L for 1mm thick birla wall care white putty or JK White wall care putty on new and old surfaces complete all as specified and directed

M&L for 15mm thick base plaster in cement mortar (1:4) roof etc admixing "Dr. Fixit Pidiproof" @ 200 ml per bag of cement at any location upto 12m height complete all as specified and directed. (Water proofing compound will be measured and paid for separately as supply only).

Supply only liquid waterproofing compound(ISI marked) complete all as specified and directed.

M&L single side pre laminated Solid PVC Wall Lining consisting of 5mm thick PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications and drawing the colour,shade of PVC wall panelling will be as per sample approved by GE(I) and shall be of Rajshree or any other equivalent including packing of cornices of window, door and wall and 5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC Frame of size n exc 600x600mm as approved by GE(I) complete all as specified and directed. Note : The measurement will be taken of face only and rates included beading & moulds on overlapping of PVC panelling & corner moulds of jamb of window, doors & walls.

Demolition stone slabs and tiles of any description or thickness in floor, apron etc laid, bedded and pointed in any mortar, complete all as specified and directed

Marble work 18 to 20mm thick (table rubbed and polished) in steps, jambs, pillar, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marbles shade of Markrana White

M&L machine cut kota stone flooring of size 58cmx58cm (nearest size available) 20-25mm thick (+ 2mm thick as available in market) over cement screed bed 20mm thick in CM 1:3 laid and jointed with grey cement slurry @ 2 kg per sqm mixed with pigment to match the shade of the slab incl rubbing and polishing, complete all as specified and directed

M&L kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar laid over 15mm thick backing coat in CM 1:3, complete all as specified and directed

Rounding to edges of stone slab one edge, such as in steps, cooking platform and other similar situations

Dismantling floor, hearth of wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises out of MD land where directed complete all as specified and directed

M&L Glazed ceramic coloured tiles in vertical surface 300x450x 7mm thick set and jointed in neat cement slurry over a 10 mm thick rendering in cm 1:4 etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed .(Colour,design and pattern shalled be approved by GE(I) Make M/S somany Pikington Limited(Haryana)/Orient/Johnson(India) Private Limited as approved by GE(I).

M&L Vitrified Ceramic tiles 10mm thick light shade (square/ rectangular) polished area of each tile not exceeding 0.36 sqm in floor over 15mm thick screed bedding in cm 1:6 etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed .(Colour,design and pattern shalled be approved by GE(I) Make M/S somany Pikington Limited(Haryana)/Orient/Johnson(India) Private Limited as approved by GE(I).

M&L Vitrified Ceramic tiles 10mm thick light shade (square/ rectangular) polished area of each tile not exceeding 0.36 sqm for work on vertical surfaces such as skirtings, dados and risers to steps etc floor over 10mm thick rendering in cm 1:4 etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed .(Colour,design and pattern shalled be approved by GE(I) Make M/S somany Pikington Limited(Haryana)/Orient/Johnson(India) Private Limited as approved by GE(I).

M&L for non skid ceramic coloured tiles printed 7 to 8 mm thick (square/ rectangular) area of each tiles exceeding 0.11 Sqm but not exceeding 0.18 Sqm as in floors etc; set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match the shade of tile over 15mm thick screed bed in CM 1:6 complete all as specified and directed.

M/S UNIQUE ENTERPRISES

classic contriction co.