GE 874/EWS-31/2020-21

Amount

Excavation in trenches not exceeding 1.50m wide and not exceeding 1.50m in depth and getting out in any type of soil, complete all as specified & directed.

Excavation over area 1.5 m in width and n exc 3.00 m deep and getting out in any type of soil , complete all as specified and directed.

Demolition of cement Concrete in ground floors and pavings(Un-reinforced) n exc 15 cm thickness (below or above ground level), complete all as specified and as directed.

Dismantling plain or corrugated steel sheeting any gauge thickness in roof covering.

Dismantling of timber scantling 40 sq in ec In any position in unframed work.

Ditto all as pre item Ser no 03 above but reinforced cement concrete.

Dismantling of wall and ceiling boards (fibre, pulp, insulation etc) any thickness including cover fillets all as specified & directed

Dismantling in fillets,rails,posts,rafters,purlins,etc in framed wood work under 40 sqcm in section complete all as specified.

Taking down cement plaster on stone or brick walls etc including racking out joints, hacking for key scrubbing down with water etc.complete all as specified.

M&L 50mm thick PCC 1:3:6 type C-2 (using 40mm stone aggregate) as in sub-bases complte all as specified and directed.

M&L 50mm thick PCC 1:3:6 type C-1 (using 40mm stone aggregate) as in sub-bases complte all as specified and directed.

Add to finishing to drain or chainal width or girth not exc 30cm all as specified.

20 mm thick screed bed in CM (1:4) laid over sub base for laying kota stone/granite slab in floor complete all as specified.

M&L for Machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete.

M&L for reinforced cement concrete 1:2:4 type B1 using 20mm graded stone agg as in shelves and minhole cover slab etc.

Dismantalling of brick or stone masonry, built in cement mortar including all quoins, arches, pillars etc but excluding ashlars facings, dressed stone work, and precast concrete arches etc.

Rolling and consolidation formation surfaces in cutting/filling in any type of soil rolled with 8 to 12 tonned power roller

150m thick (spread thickness) soiling (sub base) with brocker boulder or quarried stone, inter sticks filled surface formed and rolled and consolidated to required gardient and camber complete all as specified.

150mm thick (compound thickness) in two layers, WBM, with coarse aggregate of grading 2 (63 to 40mm size) or of grading 3 (50 to 20mm size ) using the stone, sand stone, filet to quartz spred, rolled and consolidated to gradient and camber required complete all as specified.

M & L for cement concrete work in pavement/ hard- standing of flexural strength 40 kg/ per square centimetre in field using 400 kg of cement per cubic metre,thickness of concrete 25 cm or less(15mm thickness) completer all as specified and directed.

Forming 20mm thick Expansion joints filled with pre - formed bituminious filler and top 30m primed and sealed with sealing compound, Grade A (thicknes of concrete slab 150mm) complete all as specified.

Forming construction joints 30 mm deep x 10 mm wide, filled with sealing compound 'A' grade, complete all as specified and directed by Engr-in - charge

Forming contraction (Dummy) joints by using mechanical equipment (dimond cutter) 65 mm deep x 10 mm wide filled with sealing compound grade 'A', complete all as specified and directed.

M&L for finishing surface of concrete pavement, by brooming complete all as specified and directed.

Plain cement concrete 1:4:8 type D-2 (using 40mm graded crushed stone aggregate) as in foundations filling and mass concrete, complete all as specified.

Rolled mild steel works as in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (beam, tee, angle, channel or flat sections) including distance pieces, cleats etc Fe 410W (Gde E-250), quality 'A' complete all as specified.

Two coats of synthetic enamel paint over a coat of pink primer on new wooden or plywood surface of any description, not otherwise described over 10 cm width or girth, incliding preparation of surfaces complete, all as specified.

Prepration of new wooden surface Two coat of synthetic enamel paint including cleaning dusting of new or previously untreated wood of plywood base surfaces for wall, door, window, ventilator and ceiling not otherwise described over 10cm width or girth, complete, all as specified and directed.

Two coats of synthetic enamel paint over a coat of pink primer on new wooden or plywood surface of any description, not otherwise described n exe 10 cm width or girth, incliding preparation of surfaces complete, all as specified.

One coat of synthetic enamel paint including preparation on old painted wooden or wood base surface of any description, not otherwise described over 10cm width or girth, complete, all as specified and directed

Removal of excavated material to a distance not exc.50 m and depositing where directed at a level not exceeding 1.5 mtr above starting point, complete all as specified and directed

75 mm thick PCC 1:3:6 type C-2 (using 40mm graded crushed stone aggregate) as in sub base of floor finishing surface even, complete all as specified and as directed.

40 mm thick PCC 1:3:6 type C-2 (using 40mm graded crushed stone aggregate) as in sub base of floor finishing surface even, complete all as specified and as directed.

Surface excavation not exceeding 30cm deep and averaging 15 cm deep and getting out in any type of soil, complete all as specified and directed.

M&L 50 mm sand cushion under paving block including watering and consolidation for interlocking tiles all as specified.

Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade with grey cement and pigment complete all as specified and directed.

Plain cement Concrete 1:2:4 type B-1 (using 20mm graded crushed stone aggregate) as in copings, hold fasts plinth band, bed blocks and like slightly rounded or chamfered angles as directed including necessary form work and finishing exposed surfaces as per the relevant clause of SSR Part-I, complete all as specified and directed.

Returning, filling in, including spreading, leveling, watering and well ramming in layers not exceeding 25cm, in any type of soil, complete all as specified and as directed.

RCC nominal mix 1:2:4, type, B-1 (using 20mm graded stone aggregate), as in foundation , including raft , footing , foundation beam, plingth beam base for column etc complete all as specified.

M&L RCC (Nominal mix) type B1 1:2:4 (using 20 mm graded aggregate), as in slab supported on walls, beams,beams and columns in floors, roofs, landing balcony, canpoies, deck slab and in shelves and the like complete all as specified.

RCC (nominal mix) type B0 (1:2:4) using 12.5mm graded crushed stone aggregate as in footing, columns complete all as specified.

Form work to sides of concrete foundations, footings, basis of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams and similar work; vertical or to better with rough finished surfaces of concrete complete all as specified & directed.

Form work to sides and soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work complete all as specified & directed by Engineer-in- charge.

Form work to edges of concrete flats, breaks in floors, openings in concrete walls. Floors, and roofs and RCC/PCC bands in walls, horizontal or sloping, and similar work complete all as specified & directed by Engineer-in- charge.

100 mm thick PCC 1:3:6 type C-2 (using 40mm graded crushed stone aggregate) as in sub base of floor finishing surface even, complete all as specified and as directed.

100 mm thick PCC 1:2:4 type B-2 (using 20mm graded crushed stone aggregate) as in sub base of floor finishing surface even, complete all as specified and as directed.

M&L for 15mm thick cement plaster cement mortar 1:4 finished on other then face of brick or concrete surface finioshing the surface even and smooth without using extra cement, complete all as specified.

15mm thick rendering in CM 1:6 on other than fair faces of brick or stone masonry surfaces & finishing the surface even and smooth without using extra cement, complete all as specified.

Supply and fixing TMT bars, 10mm dia and over, cut to length, bent to shape required including cranking, bending spirally or hooping for column, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90mm dia complete all as specified.

Supply and fixing TMT bars, 5mm dia and over upto incl 10mm dia, cut to length, bent to shape required including cranking, bending spirally or hooping for column, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90mm dia as in stirrups, complete all as specified.

M&L Brick work with subclass ‘B’ bricks straight or curved on plan exc 6m mean radius, built in CM 1:4 all as specified and directed

M&L Brick work with subclass ‘B’ bricks straight or curved on plan exc 6m mean radius, built in CM 1:6 all as specified and directed

M&L Brick work with subclass ‘B’ bricks straight or curved on plan any radius in half brick thick wall, built in CM 1:4 complete all as specified and directed

Walling of random rubble stone masonry uncoursed, well bonded, bedded and solidly hearted, built in cement mortar (1:6), complete all as specified.

M&L for Walling of random rubble stone masonry uncoursed, well bonded, bedded and solidly hearted, built in cement mortar (1:4), complete all as specified and directed.

All as per items no 22 above but expect stone complete all as specified

Extra over stone walling for hammer dressing with maximum depression on face from straight edge held against the dressed surface not exceeding 20mm to face stones (lime and sand stone) and dressing of face beds and joints, complete all as specified.

Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing, confirming to Fe-290-W (Gde E-165) complete all as specified

Applying three coats of white wash including preparation of newly plastered/un plastered surfaces of wall complete all as specified.

M&L Preparation of new plastered surface of walls including cornices plaster etc, and applying two coats of cement base paint over a coat of approved primer, complete all as specified and directed.

M&L for prepration of new plastered surface of wall applying three coat of OBD over a coat of primer complete all as specified.

M&L for prepration of new plastered surface of wall applying three coat of OBD over a coat of primer complete all as specified.

S&F pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified.

S&F pre- painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified.

M&L for 16 to 20 mm dia mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, length of bolt exc 5cm but n. exc 10cm long complete all as specified and directed.

0.63mm thick galvanised corrugated mild steel sheeting with Zinc coating of 120 gms/Sqm with two corrugation side lap and at least 150 mm end lap , fixed with coach screws and washers in roof, walls etc, complete, all as specified.

All as ser iten no 68 abovere but except sheeting, complete, all as specified.

0.80mm thick plain galvanised mild steel sheeting with grade of zinc coating 120 gm/sqm as in ridge, hips, valley gutters, drip and straight flashing, fixed with coach screws in roof etc, complete, all as specified.

S&F 2mm thick fiber glass reinforced translucent corrugated sheeting with two corugation side lap fixed with coach screw and washer in roof wall etc.

Two coats of synthetic enamel paint over a coat of red oxide primer including preparation of new or previously Untreated steel surfaces of any description with mordant solution including washing and cleaning etc not otherwise described, over 10cm width or girth, complete, all as specified and directed by Engr-in-charge.

S&F in repair sink made of stainless steel 1mm thick kitchen or laboratory with plug , washer and waste, includding bedding in cement mortar on to dwarf wall or including fixing cantiliver brackets and connecting union to pipe, over aal size 495mmx420mm , bowl size 410mmx330mmx160mm complete all as specified and directed.

S&F for 18mm thick one side prelaminated/decorative board fixed with supporting beads of 2nd class hard wood in cup board portion shelves etc all as specified and directed

S&F for 30mm Continuous (piano) hinges, mild steel, bright finish or electrogalvanised complete all as specified and directed

S&F for 75mm long brass handels cast type polished.

S&F for 65mm brass drawer locks,Grade I type with 4 lever fixed in complete all as specified

S & F Second class softwood as in scantling, clean sawn fixed in position with nails, unframed work, complete, all as specified and directed.

S & F Second class softwood as in scantling, clean sawn fixed in position but except wood complete, all as specified and directed.

S& F 20mm thick, second class soft wood boarding, planed one side, with butt joints and fixed with nails in facia, eaves boarding,(except flooring and skirting) complete all as specified and directed.

Dito as per item no 82 but 50mm thick as in joist of celling board.

M & L Chequered cement concrete tiles 200x200x 25mm thick, set, jointed and pointed in neat cement slurry in floors with grey cement and with pigment to match shade of tiles, over and including 15mm thick screed bed in CM (1:6), over and including 25mm thick PCC 1:2:4 type B-1 (using 20mm graded crushed stone aggregate) as in sub base complete all as specified and directed.

6mm thick plywood grade BWR type BB fixed with nails to timber frame work as on wall, complete all as specified.

M&L 6mm thick plywood ( 5 Nos of Ply) grade BWR type BB fixed with nails to timber frame work, fixed in lining / walls as in ceiling, complete all as specified.

Plain fillets, rectangular or triangular in section clean sawn, secured with nails or brads 13sqcm & not exceeding 25sqcm, second class soft wood (Kail) complete, all as specified.

Plain fillets, rectangular or triangular in section clean sawn, secured with nails or brads sectional area exc 3Sqcm & nexc 6Sqcm, second class soft wood, complete all as specified.

M&L 12mm thick plywood ( 5 Nos of Ply) grade BWR type BB fixed with nails to timber frame work, fixed in lining / walls as in ceiling, complete all as specified.

M&L Hard core of broken stone/boulders of gauge exc 63mm deposited spread and leveled in layers n exc 15cm thick watered and rammed to a true surface, complete all as specified.

Spreading and levelling in layers not exc. 25cm thick and well ramming including watering the earth under floor, complete all as specified and directed.

75 mm thick PCC 1:4:8 type D-2 (using 40mm graded crushed stone aggregate) as in floor/sub base finishing the surface even and smooth without using extra cement, complete all as specified and as directed.

75 mm thick PCC 1:3:6 type B-2 (using 40mm graded crushed stone aggregate) as in floor/sub base finishing the surface even and smooth without using extra cement, complete all as specified and as directed.

M&L 25mm thick PCC 1:2:4 type B-1 (using 20mm graded crushed stone aggregate) as in flooring finishing the surface even and smooth without using extra cement, complete all as specified and directed.

M&L Non skid coloured ceramic tiles 7 to 8mm thick area of each tile exc 0.06Sqm but n exc. 0.11Sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, laid over and including 15mm thick screed bed in CM (1:4), complete all as specified and directed

M&L Non skid coloured ceramic tiles 7 to 8mm thick area of each tile exc 0.11Sqm but n exc. 0.38Sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, laid over and including 15mm thick screed bed in CM (1:4), complete all as specified and directed

M&LGlazed ceramic coloured tiles (300x200mm) x 7mm thick, as in vertical surfaces such as in skirting and dado etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles including 15mm thick backing coat in CM 1:4, complete all as specified and as directed.

M&L for vitrified ceramic tiles 10 mm thick area of each tile but not exceeding 0.36sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match, including 15 mm thick screed bed in CM 1:4 complete all as specified and directed.

M&L12mm thick rendering in CM 1:4 on fair faces of brick or concrete surfaces & finishing the surface even and smooth without using extra cement complete all as specified.

50mm thick PCC 1:3:6 Type C-1 (using 20mm graded crushed stone aggregates) laid in alternate bays (not exceeding 2 sqm each) as in plinth protection, finished even and smooth without using extra cement including filling the joint with mastic filling comprising 3 parts of sand & 1 part of heated bitumen 85/25 grade (by weight) all as specified.

Vitreous china Wash hand basin, white, flat back of size 550x400mm including brackets, brass chromium plated waste coupling, and waste pipe PVC 32mm dia including cutting for and pinning in ends of brackets or erecting stand and embeded in cement etc, complete all as specified.

S&F Vitreous china Wash hand basin virtically mounted fency bowl flat back of size 550x400 mm including brackets,cutting for and pinning in end of bracket or erecting stand including brass chromium plated union/ waste fitting of 32mm dia and discharge pipe of PVC 32mm dia 1.0 m length including one CP pillar tap, cast copper alloy with all fitings etc complete all as specified and directed.

Vitreous china bowl urinal flat back, size of 65x355x265mm white (minimum), with grating and union for discharge pipe including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws and pointing around urinal back in cement etc and 32mm dia PVC waste pipe, complete all as specified.

Dismantling AC drain pipes(rain water pipe) 100mm dia fixed to walls and cement mortar complete all as specified.

Dismantling boarding of any description fixed in any position with nails, complete all as specified and directed.

PVC (SWR) pipes 110mm dia any length single socketed with rubber ring joint, laid in trenches or in floor/walls as soil pipe, fixed, complete all as specified and directed.

PVC (SWR) pipes 75mm dia any length single socketed with rubber ring joint, laid in floor/walls/trenches as soil pipe(vent pipe), fixed, complete all as specified and directed.

PVC (SWR) bends any radius 110mm bore, complete all as specified.

PVC (SWR) junction single (single 'T') 110mm dia with each over assessed door, complete all as specified and directed.

PVC (SWR) floor trap of 75mm dia of outlet, plain with grating including jointing with solvent cement fixed, complete all as specified.

Tacking up or down 15mm steel tubing and connection in walls , celling , floor etc including cleaning for refixing or removal to store complete all as specified.

Tacking up or down 20mm steel tubing and connection in walls , celling , floor etc including cleaning for refixing or removal to store complete all as specified.

S&F steel water tubing 15mm bore ‘medium grade’ galvanized with all fittings like socket, union, elbow, bend, tees etc fixed to walls and ceiling or laid in floors, complete all as specified.

S&F steel water tubing 20mm bore ‘medium grade’ galvanized with all fittings like socket, union, elbow, bend, tees etc fixed to walls and ceiling or laid in floors, complete all as specified.

Ditto all as per item ser no 113 but fiing onely of 15mm dia GI tubingcomplete all as specified.

Ditto all as per item ser no 114 but fiing onely of 20mm dia GI tubing complete all as specified.

Lagging to pipes 15mm bore used in internal water supply or plumbing all round with 25mm thick bonded mineral wool preformed 'SNAP ON' pipe sections of density 144Kg/Cum conforming to IS-9842 provided with chicken mesh wire netting 25 gauge, 20mm mesh, and covered with 0.01mm aluminium foil, complete all as specified.

Lagging to pipes 20mm bore used in internal water supply or plumbing all round with 25mm thick bonded mineral wool preformed 'SNAP ON' pipe sections of density 144Kg/Cum conforming to IS-9842 provided with chicken mesh wire netting 25 gauge, 20mm mesh, and covered with 0.01mm aluminium foil, complete all as specified.

Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing complete all as specified.

Factory Made Solid PVC Moulded Door Shutter with particle board, 28 to 30mm thick (styles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site all as specified and drawing given SSR Part-II complete all as specified.

PVC connection 15mm size with PTMT nuts on both ends of length 600mm, complete all as specified.

S & F Sheet glass ordinary quality, 3mm thick, glazing with oil putty or wooden beads in squares not exceeding 0.50Sqm in each pane, complete all as specified and directed.

Rotational moulded polyethylene water storage tank tripple layered cylindrical vertical with closed top 500 litre capacity hoisted and fixed in position, connecting to inlet and outlet pipe connections, with and including 20mm dia GI wash out with plug, complete all as specified and directed.

Rotational moulded polyethylene water storage tank tripple layered cylindrical vertical with closed top1000 litre capacity hoisted and fixed in position, connecting to inlet and outlet pipe connections, with and including 20mm dia GI wash out with plug, complete all as specified and directed.

Bib taps 15mm bore of cast copper alloy chromium plated fancy type, screwed down, high presure with crutch or butterfly handle, screwed both ends for iron pipe or for brass ferrule, and fixed, complete all as specified and directed.

15mm bore pillar tap fancy type cast copper alloy with capstan head, chromium plated, screwed down, high pressure with or without lettered 'Hot' or 'Cold' with long shank and fly nuts screwed for iron pipe or for brass ferrule and fixed complete, all as specified & directed

S&f for CP mixer pillar tap for mixing hot & cold water screwed doen for iron pipe and fixed in repair in complete all as specified and directed.

M&L for decorative type power coated drapery rod 20mm dia with powder coated fancy type end knob and fixing bracket as per design approved by GE complete all as specified and directed.

Stainless steel plate rack made out 1.00 mm thick over all size 900x1200mm complete all as specified and directed. .

S & F in 15mm bore stop valve, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed, complete all as specified.

S & F in 20mm bore stop valve, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed, complete all as specified.

Taking down chowkats (without taking off door shutters or frames) area not exceeding 1.5 Sqm each.

Taking down chowkats or frames with shutters (without taking off shutters from the frame) area exc. 1.5 Sqm and n.exc. 4 Sqm each, complete all as specified and directed.

2nd class softwood, plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, complete all as specified.

Mild steel FI as in hold fasts and similar small articles fixed to chowkats, size 25mm x 3mm conforming to Fe-290 Gde E-165, complete all as specified and directed.

30mm thick 2nd class soft wood Glazed and skelton shutters, open rebated and prepared to receive glass, gauge etc (divided into square with sash bars), edges of framing plain, chamfered or rounded fitted with cut and mitered beads for securing glass etc. size of members of shutters as specified in SSR Part-I, Section 8, clause 8.24 (b) supplied and fitted to chowkats complete, all as specified.

M&L for 2nd class soft wood Glazed and skelton shutters, open rebated and prepared to receive glass, gauge etc (with sash bars), edges of framing plain, chamfered or rounded fitted with cut and mitered beads for securing glass etc.supplied and fitted to chowkats, 30mm thick shutter as specified in SSR Part -I section -8, clause8.24 (b) for window etc.

Mild steel butt hinges, medium weight, cold rolled,100mm long, ISI marked complete all as specified.

Mild steel butt hinges, medium weight, cold rolled, 75mm long, ISI marked complete all as specified.

250mm long aluminium alloy, anodised, sliding door bolt ISI marked with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section and fixed, all as specified and directed.

125 mm long aluminium alloy, anodised, sliding door bolt ISI marked with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section and fixed, all as specified and directed.

Mild steel pressed handle, oval type stove enamelled, black of size 150mm, complete all as specified.

Mild steel pressed handle, oval type stove enamelled black of size 75mm, complete all as specified.

Mild steel barrel tower bolt, stove enamelled black, with bright bolt of 125 mm long, complete all as specified.

Mild steel pressed handle, oval type stove enamelled black of size 100mm, complete all as specified.

Mild steel barrel tower bolt, stove enamelled black, with bright bolt of 150 mm long, complete all as specified.

S&F 200mm long Aluminium alloy, anodised, barrel tower bolts of extruded section ISI marked.

Mild steel barrel tower bolt, stove enamelled black, with bright bolt of 75mm long, complete all as specified.

Galvanised mild steel wire cloth 0.56 nominal dia of wire and average width of aparture 1.18mm and fixed with tinned tacks or galvanised wire staples fixed in repair, complete all as specified.

M&L for 300mm mild steel ordinary rat tail rod patrtern spring including roller and roller plates complete all as specified.

Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone/ concrete, glazed with putty or fixed with beads, complete, all as specified and directed.

S&F urinal spreader of PTMT any colour for fixing with 15 mm dia pipe (min wt 60 gms) complete all as specified.

S&F high density 32 mm dia HDPE pipe for pressure rating 6kgf/sqcm complete all as specified.

S&F for Waste coupling of PTMT (half or full threaded) (Minimum weight 32mm-45gms/40mm-60gms) for 32mm bore dia of discharge pipe fixed in repairsto WHB, sink complete all as specified.

M&:L for providing 38 mm glass dividing strips ,30mm thick complete all as specified.

Extra over stone walling for hammer dressing with maximum depression on face from straight edge held against the dressed surface not exceeding 20mm to face stones (lime and sand stone) and dressing of face beds and joints, complete all as specified.

S&F Cp grating 125mm dia round fix on floor/ nahni trap fixed with cement mortar complete all as specified and directed (Make: as per sample)

Towel rail 600mm long of PTMT fixed with and including chromium plated brass screws and wooden/plastic cleats (minimum weight 190gm), complete all as specified and directed.

S&F 20 mm dia Gun metal glope or gate valve with iron wheel head screwed both ends for iron pipe and, complete all as specified and directed.

S&F 15 mm dia Gun metal glope or gate valve with iron wheel head screwed both ends for iron pipe and, complete all as specified and directed.

300mm ordinary rat tail Mild steel rod pattern springs including roller and roller plate complete

Extra for forming fair finished drain or channel 30cm inner girth in cement concrete using extra cement complete all as specified.

Construction of soakage well, of internal dimensition 1.8 mtr diax3 mt effective depth excavation, in any type of soil, foundation in PCC 1:3:6 type C1, as in footing, wall of honey combed/ solid masonry with top ring of M25 concrete including intercepting chamber and screen chamber made of brick masonry in CM 1:4, RCC cover slab in M25/SFRC cover, interconnecting pipes of RCC/DWC complete filled with brick bats, all as specified and shown in Drg No. CESZ/TD- 01/2015 sh 3/3 dated 22/2/15 & revised on 06/06/15.

Construction of soakage well, of internal dimensition 1.2 mtr diax3 mt effective depth excavation, in any type of soil, foundation in PCC 1:3:6 type C1, as in footing, wall of honey combed/ solid masonry with top ring of M25 concrete including intercepting chamber and screen chamber made of brick masonry in CM 1:4, RCC cover slab in M25/SFRC cover, interconnecting pipes of RCC/DWC complete filled with brick bats, all as specified and shown in Drg No. CESZ/TD- 01/2015 sh 3/3 dated 22/2/15 & revised on 06/06/15.

Plain cement Concrete 1:2:4 type B-1 (using 20mm graded crushed stone aggregate) as in post manhole cover slabs, chullahoods,,chajjas etc including necessary form work. complete all as specified and directed.

Plain cement concrete 1:2:4 type B-2 (using 40mm graded crushed stone aggregate) as in surface channels and drain, complete all as specified.

Concrete bed to drain pipes including packing under and haunching against the sides of pipes for 150mm SGSW pipe after they are laid and tested in PCC (1:3:6) type C-2 (using 40mm graded crushed stone aggregate) complete all as specified and directed.

150 mm bore salt glazed stone ware drain pipes, grade ‘A’ laid in trenches and jointed as specified and all as directed by Engr-in-Charge.

Cuting the 25/40 mm dia GI pipe and fixing the required length/ insertion of tee for new GI pipe connections complete all as specified.

10mm thick rendering in CM 1:6 asd in internal plaster on fair faces of brick nasonarywall and even and smooth

M&L PCC 1:3:6 type C-2 (using 40mm graded crushed stone aggregate) as in foundation, filling mass concrete/surface channels and drain complete all as specified and as directed.

Extra for forming fair finished drain or channel 30cm inner girth in cement concrete using extra cement including forms, moulds, mitred/stopped ends etc complete all as specified.

M&L 40mm thick PCC 1:2:4 type B-1 (using 20mm graded crushed stone aggregate) as in flooring finishing the surface even and smooth without using extra cement, complete all as specified and directed.

Dismantling of 300 dia cast iron or reinforced concrete drain pipes , jointed in CM and taking out trenches ,if required.

S&F for RCC pipes class NP 2 laid and jointed complete all as specified with coller bore of pipe 150mm complete all as specified and directed.

Precast cement concrete (1:2:4) using 20mm graded crushed stone aggregate as in landings, cover slab (for manholes etc), chullah hoods, chajjas, water troughs, shelves and similar articles with plain fair faces including chamfers, weatherings, throating etc. and setting in cement mortar (1:4) including necessary form work complete all as specified and directed by Engineer-in-Charge.

M&L for 20 mm thick Granite (of any type) tiles machine cut in skirting/dado laid over cement slurry and pointed with white cement with admixture ofpigement to match the shade of granite stone incl grinding and polishing, complete all as specified and directed.

Brass handle, cast type, polished bright of size 75mm, complete all as specified and directed.

Taking down carefully copper/ aluminium unserviceable/ perished point wiring (light, fan, socket or power complete including fixture and fittings such as switches, ceiling roses, pandents, regulators, sockets, light fittings,removing material from site for taking credit etc and making good disturbed surfaces of wall, floors, complete all as specifiecd and directed.

Points wiring for one light point/fan point controlled by one switch with 1.5 sqmm PVC FR insulted un-sheathed copper conductor single core multi strand flexible cable and 1.5 sqmm PVC FR insulted un-sheathed copper conductor single core multi stranded flexible cable as earth lead (using colour coding) in and including cable 1100 volts grade including casing and capping (ISI marked) for one light/fan point including 2nd class hard wood rectangular block open recessed cover with 3mm thick plastic laminated sheet cover including cutting chases to wall making good the distrubed surfaces to match with the existing specification complete all as specified.

All as per description all as per item No.53 above here in before, but for 3 Pin socket outlet 5 Amps on same board, with cable 2.5Sqmm size, insulated copper conductor cable 1100 volt grade with continuous PVC insulated copper conductor cable of 1.5 Sqmm, complete all as specified and directed.

All as per description all as per item No.53 above here in before, but for 3 Pin socket outlet 5 Amps point on Independent board, with cable 2.5Sqmm size, insulated copper conductor cable 1100 volt grade with continuous PVC insulated copper conductor cable of 1.5 Sqmm, complete all as specified and directed.

Point wiring for 3 pin socket outlet 15 Amps on the independent board controlled by one switch with 4.00 sqmm PVC FR insulted un-sheathed copper conductor single core multi strand flexible cable and 2.5 sqmm PVC FR insulted un-sheathed copper conductor single core multi stranded flexible cable as earth lead (using colour coding) in and including cable 1100 volts grade including casing and capping (ISI marked) for one light/fan point including 2nd class hard wood rectangular block open recessed cover with 3mm thick plastic laminated sheet cover including cutting chases to wall making good the distrubed surfaces to match with the existing specification complete all as specified.

LED retrofit T8 type flourescent tube light fitting patti type 1x20 watts white powder coated CRCA sheet steel rust free housing complete with replaceable electronic ballast, polycarbonate spring loaded bipin holder with bracket, connector block all accessories prewired with suitable size cable with decorative end caps including 1x20 watt LED tube rod and connecting electrically using PVC insulated and overall sheathed flexible copper conductor cable of size 0.75 sqmm 3 core complete all as specified and directed. of cat pat No. LTDCO1220WLED /WD of make C&S or equivalent make of Bajaj/ Crompton/philips

S&F of decorative LED batten for surface and pendent application. Anodized extruded aluminium housting high transmisitivity diffuser, high lumen output of VIVA MINI LED Luminaires (4FT) of 20 Watt connecting up with twin core twisted flexible copper conducter cable of suitable size complete all as specified and directed.

Supply and fix LED light fittings 1X9 W bulk head luminaires etc complete with all accessories and including connecting up with twin core twisted flexible copper conductor cable with suitable size of 230 volt 50 HZ make Havells, Bajaj, Phillips complete all as specified.

S&F Switch piano flush type 6 Amp single pole one way, (ISI marked), complete all as specified.

Ceiling rose, PVC/poly carbonate, isolated body three terminal complete all as specified and directed.

S & F Switch Socket combination 5 in 1, 5 and 15 Amp flush type universal controlled by one switch (ISI Marked) complete all as specifed and directed.

S & F Switch Socket combination 5 in 1, 6 Pin and 15 Amp flush type universal controlled by one switch (ISI Marked) complete all as specifed and directed.

S/F rectangular boards/ blocks 30x25x4cm depth closed recessed, complete all as specified and as directed by Engr-in -charge.

S&F Sheet metal enclosure factory made for DBs single pole and neutral double door 240 volts 4 way with 200 Amps rated bus bar fixed on walls, including dressing and connecting both incoming and outgoing cable termination with proper taping, lagging testing and commissioning and making good of wall, surfaces all as specified and directed. Make : Havells/lEGRAND/SSK

S&F MCB's single pole and neutral, 240 volts 6 to 40 Amps all as specified and as directed by Engr -in-Charge. Make: Havells/Legrand/Philips.

S&F MCB's single pole 240 volts 6 to 32 Amps all as specified and as directed by Engr -in-Charge. Make: Havells/Legrand/Philips.

House service bracket (hook type), complete, with 3m long GI pipe 40mm dia medium grade, two Nos 90 degree bend, MS hook and guy or stay, complete all as specified.

Supply & fix exhaust fans AC single phase 230/ 240 V of size 450 mm sweep with louver Make : Havells/Bajaj/Philips or equivalent

Supplying and fixing 1100 volts grade heavy duty cable PVC insulated aluminium conductor, served with inner sheathing of PVC tape and overall PVC sheathed in service connections suspended by insulating hangers not more than 1 metre apart including 4mm dia suspension wire, one twin core cable flat or circular of size 10Sqmm, complete all as specified and directed.

S&f for RCBO, singal pole and neutral 240 VOLT 50Hz 10 Ka, 6/32AMPS all as specified and directed. Make havelles CAT part NO DHCEACSN2030006 to 32/Legeands/PHilips. NOTE rate are inclusive of CP 17.5 % and GST 18%

Supply and Fix Voltage stabilizer for automatic operation, single phase naturally air colled indoor type & designed for input varition between 110V to 290 V with output voltage stabilized at 230 V with accuracy of +_ 2.5%, 4-6 Sec initial delay and of capacity 6.6 KVA / 30 A Make V Guard Model No VGMW1000PLUS OR equivalent as approved by Engr-in-charge

S&f water hearter storage type, electric, Cap 25 Ltr. BEE 5 strar rated Make havells/Bajaj/phillips/or equivalent as approved by Engineer-in-charge

M/S SAJAA CONSTRUCTION COMAPNY

M/S MANZOORAHMAD LONE

patriotic builders