REPAIRS TO JOINERY, ROOF TREATMENT, SANITARY FITTINGS AND OTHER ALLIED WORKS IN TECH AREA AND MAINTENANCE OF RUNWAY SHOULDERS/SGA BY PLOUGHING AND SOIL FILLING AND GRASS CUTTING UNDER GE (AIRFORCE) LOHEGAON AT AIR FORCE STATION PUNE

Amount

Dismantling stone slabs or roof treatment of any description in suspended slabs in roofs,suspended floors, chajjas, landings etc,including cement mortar, bedding (But not backing ) and rubbish of premises complete all as specified and directed.

Demolition of cement concrete in any description and any position not otherwise specifically provided for complete all as specified and directed.

Cutting out cracks to V section in existing roofs or terracing ,cleaning out ,wetting, grouting with cement and sand slurry 1:3 complete all as specified and directed.

M&Lfor brushing neat cement slurry with 3.0 Kg of cement per Sq.meter. complete all as specified and directed.

M&L for 10 mm thick rendering on fair faces of brick works / Concrete surfaces finished even and smooth without using extra cement in cement mortar 1: 3 complete all as specified and as directed

M&L for PCC type B0 (1:2:4) using 12.5 mm graded crushed aggregate in Coping / Coving/padding concrete,mass concrete and the like complete all as specified and directed.

M&L for priming surfaces in moderate conditions for laying APP membrane complete all as specified and directed.

M&L APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforment with polyster non woven fabric (wt reinforcement not less than 150 gms/sqm) laid on primed surfaced application complete all as specified and directed. (Primer shall be measured and paid as per Ser Item No. 7.00 above)

M&L applying two coat of Aluminium paint over APP Membrane complete all as apecified and directed.

Dismantling plain or corrugated steel /fibre/AC sheeting any guage thickness including nanital or similar pattern complete all as specified and as directed

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

S&F MS Rolled sections in main and cross beams,hip and jack rafters ;purlins where connected to common rafters running rails and guids for sliding doors ;fixed with angle cleats or other connecting plates and similar work confirming to Fe-290, Gde-E-165 complete all as specified and as directed.

S&F MS Wind ties for roof including securing bolts, posts & struts including cutting tops to shapes as directed,including all necessary drilling,bolting or reveting etc and similar work confirming to Fe-290, Gde-E-165 complete all as specified and as directed.

S&F 0.56mm aluminium semi corrugated sheeting Alloy 31000 H4, STUCCO Embossed finish with side lap as specified by the manufacturer, fixed with coach screw and aluminium washer in roof and wall etc. with end laps stitched with 25 x 6mm G.I bolts at 20cm apart complete all as specified and directed.

S&F 0.56mm Plain aluminium sheeting alloy 31000 H4 in ridges ,hips,valley gutter,drip and straight flashing (length and girth as foxed) complete all as specified and directed.

S&F Fibre glass reinforced translucent plain sheeting 2mm thick with two corrugations side lap fixed with coach screw and washer in roof ,wall etc complete all as specified and as directed

M&L applying two coats of camouflage pattern synthetic enamel painting to new surfaces of steel/ roofing sheets of any description over a coat of red oxide primer exc. 10 cm width/girth including preparation of surfaces, removal of galvanisation if reqd , including filling with filler where reqd complete all as specified and directed.

M&L for preparation of existing treatment on steel / Roofing sheets of any descripton and applying one coat of camouflag pattern synthetic enamel paint complete all as specified and as directed.

Taking down chowkats / frames with shutters (without taking off shutters from the frames) area n'exc 1.5 Sqm each complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) area exceeding 1.5 Sqm and not exceeding 4 Sqm each complete all as specified and directed.

Taking down shutters of any description area exceeding 1 Sqm and not exceeding 2 Sqm each complete all as specified and directed.

Taking down shutters of any description area not exceeding 1 Sqm each complete all as specified and directed.

Hacking old broken glass (any thick ness, size, quality or description) from aluminium/steel/wooden frame work or stone, concrete or brick surrounds, glazed with oil putty or fixed with beads complete all as specified and as directed .

Taking down shutters of any description area not exceeding 1 Sqm each easing & adjusting and refixing in the same opening complete all as specified and directed.

Taking down shutters of any description area exceeding 1 Sqm and not exceeding 2 Sqm each easing & adjusting and refixing in the same opening complete all as specified and directed.

M&L Anodised aluminium frame of standerd section for doors, windows, ventilators and partitions with double rebates including joining cleat for fixing etc. complete all as specified and directed.

M&L for powder coating in Anodised aluminium frame of standerd section for doors, windows, ventilators and partitions with etc as per item no 26 above. complete all as specified.Note: Over all weight of Anodised aluminium frame shall be considered for payment complete all as specified and directed.

M&L for Anodised aluminium door shutters, aluminium sections weeighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, anodised aluminium snap beading, screws,hinge type B-21 100mm long (3 no.) suitable handle (2 no.) (Glass / Wiremesh should be measured and paid seperately) complete all as specified and directed.

M&L for anodised aluminium window and ventilator shutters of any type with or without sash bars, aluminium sections weeighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fitings such as suitable stays ,suitable hinges (if required.) suitable handles (1 no.) (Glass / Wiremesh should be measured and paid seperately) complete all as specified and directed.

M&L for powder coating in Anodised aluminium frames of shutters of Doors ,window and ventilator openings etc as per Ser Item No 28.00 & 29.00 above complete all as specified and directed. Note: Over all area of shutters of Doors ,window and ventilator shall be considered for payment.

M&L sheet glass 5mm thick ordinalry quality and glazing with aluminium beeds in square not exc 0.50 sqm in each pane complete all as specified and as directed

Pressed steel frames of size 105x60mm for doors with one or more rebates including necessary fixings lugs,excluding hinges, lock strike plate, etc. complete all as specified and directed.

Pressed steel frames of size 125x60mm for doors with one or more rebates including necessary fixings lugs,excluding hinges, lock strike plate, etc. complete all as specified and directed.

S&F 2nd class soft wood plain, solid, straight chowkets and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, supplied and fixed complete(Glass shall be measured Seperately) complete all as specified and directed.

S&F mild steel work as in hold fasts and similar work confirming to Fe-290 or Gd -E 165 complete all as specified and directed.

M&L for treating wooden chowkats surface of any description n exc 10 cm in width or girth with black bituminus paint in two coats complete all as specified and directed.

M&L for preparing and treating small articles of builders hardware such as MS hold fasts ,MS but hinges etc, with two coats of synthetic enamal paint over a coat of primer when un connected with other paintings or when painted in a different tint complete all as specified and directed.

Material & labour PCC (1:3:6) type B0 (using 12.5 mm graded stone aggregate) as in hold fast , bed block and like complete all as specified and directed.

S&F for 30mm thick 2nd class soft wood plain framed paneled shutters (any number of panels) with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers, Supply and fixed to chowkats complete all as specified and directed.

S&F for 30 mm thick Flush shutters, solid core construction ,with block board core and plywood face panels commercial type on both sides , Supply and fixed to chowkats complete all as specified and directed.

S&F for 40 mm thick Flush shutters, solid core construction ,with block board core and plywood face panels commercial type on both sides , Supply and fixed to chowkats complete all as specified and directed.

S&F 30 mm soft wood Glazed and skelton door or window shutter, open and prapared to receive the glass, gauze etc.(without sash bars) edges of framing plain chamfered or rounded, fitted with cut and mitred beads for securing glass etc. (Glass / Wiremesh should be measured seperately) complete all as specified and directed.

S&F MS framedwork such as grills, gratings etc with ends of bars shouldered and/or rivited or forged in spikes, framed guard bars, barred iron doors, ledders framed balsters walk ways railings frame work of water tanks and similar work confirming to Fe-290, Gde-E-165 complete all as specified and directed.

S&F Steel windows (frame with shutter) with side hung shutters including projecting type hinges with steel handle ,and steel peg stay,complete with glazing bars,dovatiled or welded (Glass shall be measured Seperately) complete all as specified and directed.

M&L sheet glass 3mm thick ordinalry quality and glazing with oil putty or wooden beads in square not exc 0.50 sqm in each pane complete all as specified and as directed.

S&F Galvanised mild steel wire cloth ,0.63mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks or galvanised wire staples complete all as specified and directed.

S&F in repairs Galvanised mild steel wire cloth ,0.63mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks or galvanised wire staples complete all as specified and directed.

S&F mild steel butt hinges, medium weight cold rolled 100mm size complete all as specified and as directed.

S&F 150mm long aluminium anodized, barrel tower bolt of extruded section complete all as specified and directed.

S&F 150mm size extruded aluminium alloy handles, fabricated type, anodized complete all as specified and as directed.

S&F for factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Paneling of plain colour PVC sheet to be fitted in the M. S. frame welded/sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement, suppling & fixing in the frame at site complete all as specified and directed.

S&F solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube complete all as specified and directed.

S&F mild steel butt hinges, medium weight cold rolled 75mm size complete all as specified and directed.

S&F 100mm long aluminium anodized, barrel tower bolt of extruded section complete all as specified and directed.

S&F 100mm size extruded aluminium alloy handles, fabricated type, anodized complete all as specified and directed.

S&F in repairs mild steel ordinary rat tail rod pattern springsof size upto 300mm long including roller and roller plate complete all as specified and as directed.

S&F in repairs Aluminium alloy anodised ,sliding door bolt 250mm with hasp,staple(bolt type) and fixing clips of sheet ,cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast, aluminium alloy complete all as specified and as directed.

S&F in repairs Aluminium (extruded section) door closer hydraulically regulated ,designation No.3, universal type, suitable for door shutter of 851 to 1000mm in width and of weighjt between 61 to 80 Kg complete all as specified and directed.

S&F in repairs 100mm Aluminium Mortice lock 2 livers vertical type complete all as specified and as directed.

Dismantling wall/floor and ceiling boards (fiber, pulp, inlsulation, blankets) any thickness including covered fillets and supporting members complete all as specified and as directed

M&L Anodised aluminium snap grid frame work for false ceiling of grid size 605 x 605 mm including necessary hangar wires as per manufacturers specification complete all as specified and directed.

Providing and fixing Gypsum Board 10mm thick in ceiling fixed with screw as per manufacturers instructions complete all as specified and directed.

M&L Insulated PVC Wall & Ceiling Lining of 12.5mm thick consisting of PVC Panels Having expanded polystyrene (EPS) stuck to1.0mm thick plain colour PVC sheet duly fitted into the wall & Ceiling as per specifications and drawing complete all as specified and directed.

S&F 2.5mm thik PVC sheet fillets of width upto 35mm for wall panelling inclusive of fixing on wall to make PVC frame as per specification and drawing complete all as specified and directed.

Forming jambs, etc.in Cement mortar 1:6 to openings (to foregoing item), including cutting, toothing and properly bonding into old work, also facing, jointing and pointing to match existing work complete all as specified and directed.

Making good under cills or over arches, lintels and bressummers in Cement mortar 1:6, including all pinning when necessary complete all as specified and directed.

Taking down cement plaster any description on brick/stone or concrete walls, etc including racking out joints, hacking for key, scrubbing down with water etc.complete all as specified and directed.

Demolition of Brick/precast concrete block/Stone/boulder masonary walling built in cement mortar including all quoins, arches , pillars etc complete all as specified and directed.

M&L pre-cast cement concrete(20mm graded crushed stone aggregate) 1:3:6 type C-1 as in block masonery exc 10cm in width with solid block masonery with solid blocks,exc.10cm in width and setting in cement mortar 1:6 complete all as specified and directed.

M&L for 10mm thick rendering on fair faces of brick works finished even andfair without using extra cement in cement mortar 1: 4 complete all as specified and as directed

Supply only Liquid water proofing compound complete all as specified and directed.

M&L for 15 mm thick rendering on unfair faces of brick works finished even andfair without using extra cement in cement mortar 1:6 complete all as specified and as directed

M&L for preparation of new plastered wall surface of any description and applying two coats of cement based paint complete all as specified and as directed.

M&L for preparation of new concrete /plastered surface of any description, applaying three coat of white wash complete all as specified and directed.

M&L for preparation of new concrete /plastered surface of any description, two coat of destemper oil emulsion over a coat of primer complete all as specified and directed.

M&L for preparation of new or old untreated wood or wood based surface of any description over 10cm width or girth and applying two coat of synthetic enamel paint over a coat of pink primer as directed complete all as specified and as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (But not backing ) and rubbish of premises complete all as specified and directed.

Demolition of stone slabs and chequered tiles of any description or thickness in floors aprons etc.laid bedded and pointed in any mortar complete all as specified and directed.

Demolition of bricks (laid flat or on edge) or interlocking tiles in floors, channels, kerbes, aprons, etc laid dry or laid dry and pointed complete all as specified and directed.

Demolition of cement concrete in ground floor and pavings n'exc 15cm thickness (below or above ground level) complete all as specified and directed.

Taking down steel tubing ( 15mm bore) and connections in any position including cleaning for refixing or removal to store complete all as specified and directed.

Taking down steel tubing ( 20mm bore) and connections in any position including cleaning for refixing or removal to store complete all as specified and directed.

Dimolition and breaking up drain pipes ( salt glazedware, AC,Reinfoced concreet, PVC pipe) of internal dia upto110 mm bore, set in cement mortar and taking out of trenches if required complete all as specified and directed.

M & L for 75 mm PCC 1:3:6 type C-2 using 20mm graded aggregate as plinth protection finished even and smooth with out using extra cement complete all as specified and directed.

M & L for 75 mm PCC 1:3:6 type C-2 using 20mm graded aggregate as in sub floor or hard standing rough finished surface complete all as specified and directed.

M&L Forming Contraction (Dummy) joints 75 mm deep x 10mm wide for plinth protection & similar work , filled with sealing compound Grade 'B' in plinth protection complete all as specified and directed.

M&L for vitrified ceramic tiles 10mm thick (light shade ) (square/ rectangular) polished, area of each tiles not exc 0.36 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles complete all as specified and directed.

M&L for Non skid coloured ceramic tiles 7 to 8mm thick (Square/ rectangular) area of each tile exc 0.11Sqm and nexc .18 Sqm in floor etc set and jointed in neat cement slurry and pointed with white or coloured cement mixed with pigments to match the colour of tiles complete all as specified and directed.

M&L for non skid coloured ceramic tiles 7 to 8mm thick (Square/ rectangular) area of each tile exc 0.06 and nexc .11 sqm in floor etc set and jointed in neat cement slurry and pointed with white or coloured cement mixed with pigments to match the colour of tiles complete all as specified and directed.

M&L for screed bed with M (1:6) 15mm thick for laying floor tiles complete all as specified and directed.

M&L for Glazed ceramic coloured tiles in vertical surfaces 300 x 200 x 7mm thick set and jointed in neat cement slurry and pointed with white or coloured cement mixed with pigments to match the colour of tiles complete all as specified and directed.

M&L for Glazed ceramic coloured tiles in vertical surfaces 350 x 250 x 7mm /450 x 350 x 7mm thick set and jointed in neat cement slurry and pointed with white or coloured cement mixed with pigments to match the colour of tiles complete all as specified and directed.

M&L for rendering screed bed with CM (1:4) 10mm thick for laying wall tiles complete all as specified and directed.

S&F GI tubing of 15 mm dia medium grade with all fittings & fixed complete to walls and ceiling or laid in floors complete all as specified and directed.

S&F GI tubing of 20mm dia medium grade with all fittings & fixed complete to walls and ceiling or laid in floors complete all as specified and directed.

S&F in repairs 15mm Stope/Gate valve ,cast copper alloy,screwed down, high pressure,with crunch or butterfly handle ,screwed both ends for iron pipe or for union and fixed complete all as specified and directed.

S&F in repairs 20mm Stop/Gate valve ,cast copper alloy, screwed down, high pressure,with crunch or butterfly handle ,screwed both ends for iron pipe or for union and fixed complete all as specified and directed.

S&F Rotational moulded polyethlene water storage tanks (cylindrical vergical with closed top) 500 Ltr capacity hoisted and fixed in position including removal of existing damaged water tanks all as specified in SSR Part I complete all as specified and directed.

S&F Rotational moulded polyethlene water storage tanks (cylindrical vergical with closed top) 1000 Ltr capacity hoisted and fixed in position including removal of existing damaged water tanks all as specified in SSR Part I complete all as specified and directed.

S & F in repairs 20 mm Brass valves ,high pressure,with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed complete all as specified and directed.

Dismantling water tanks of capacity 500 liters ,cleaning and removing all scale and dirt,etc from tanks and from mouths of circulating pipes ,etc and refixing in the same position all as specified in SSR Part I complete all as specified and directed.

Dismantling water tanks of capacity 1000 liters ,cleaning and removing all scale and dirt,etc from tanks and from mouths of circulating pipes ,etc and refixing in the same position all as specified in SSR Part I complete all as specified and directed.

S & F in repair Vitreous China wash basin, white, flat back, size 450 x 300mm including cutting for and pinning in ends of brackets or erecting stand but inclusive of fixing of supply and waste pipe complete all as specified and directed.

S&F in repairs Vitreous China bowl Urinal, flat back, size of 465x355x265mm white with grating and union for discharge pipe and PTMT waste coupling with waste pipe (excluding flushing cistern, flush pipe and waste pipe) complete all as specified and directed.

S&F in repairs Vitreous china wash down water closet scouting pattern, white (EWC) including Plastic seat of same colour of WC, closed patttern with flat bottom, and cover and Mild steel chromium plated hinging device including trap set and necessary concrete complete all as specified and directed.

S&F in repairs Vitreous China Sqatting pan Orissa Pattern Indian Type Size 580 x 440 with integral foot rest (excluding flushing cistern and flush pipe). Colour as desided by Engneer-n Charge complete all as specified and directed.

S&F in repairs, 10 litres capacity PVC valveless syphonic action type, flushing cistern (ISI marked), low level with inlet, ball valve, float bracket & flush pipe complete all as specified and directed.

S & F in repair 15 mm bore pillar taps, fancy type Cast Copper alloy, with capstan heads, chromium plated, screwed down high pressure with or without lettered Hot or Cold with long screwed shanks and fly nuts, screwed for iron pipe complete all as specified and directed.

S&F in repairs Angle stop valves, cast copper alloy, screwed down high pressure with crutch or butter fly handle, fancy type, chromium plated with long shank and cup (concealed type), 15mm bore dia of pipe complete all as specified and directed.

S&F waste pipe of polyethylene of low or high density or PVC ,32 mm dia for urinal/wash basin/ flush tankfixed in repairs complete all as specified and directed.

S&F in repairs PVC connection pipe suitable for connecting flushing cistern and WHB etc 450mm long complete all as specified and directed.

S & F in repairs, waste coupling of PTMT 32mm bore for urinal / wash basin (Half or full threaded ) (Minimum Weight 45 grams) complete all as specified and directed.

S & F in repair CP floor gratings 100mm dia with o without waste hole of PTMT (mim waight 40 grms) complete all as specified and directed.

S&F in repairs bib tap cast copper alloy chromium plated butterfly handle screwed down screwed for iron pipe completed (15mm dia tap) complete all as specified and directed.

S & F 110 mm dia, PVC rain water pipes, single socketed, in any length with sealant rubber ring joints including necessary MS flat Iron clamps of size (40 x 4mm) complete all as specified and directed.

S & F 75 mm dia, PVC rain water pipes, single socketed, in any length with sealant rubber ring joints including necessary MS flat Iron clamps of size (40 x 4mm) complete all as specified and directed.

PCC 1:3:6 Type C-2 (40mm gradded aggergate) bed to drain pipe incl packing under and hanching against side after they are laid and tested up to 110mm dia pipe complete all as specified and directed.

M&L for Cement concrete type D-2,1:4:8 (40mm graded aggreate) 100 mm thick as in sub -floors ,sub- bases ,floors and pavings,etc. complete all as specified and directed.

M&L machine pressed precast concrete interlocking paver block any shape and size polished with grey cement and pigment confirming to IS 15658-2006 of 60mm thickness M-35 grade complete all as specified and directed.

M&L sand filling (50 mm average thickness) under floors in foundations and for laying Interlocking paver blocks including watering and consolidation complete all as specified and directed.

M&L PCC 1:2:4, 25 mm thick type B0 using 12.5mm graded stone aggregate as in floor finished even and fair with out using extra cement complete all as specified and directed.

M&L for Machine cut Kota stone slab flooring 20-25 mm thick including skirting cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing complete all as specified and directed.

M&L for Chequered cement concrete tiles 30cm X 30cm X 20mm thick, set ,pointed & jointed in neat cement slurry in floors polished with grey cement & pigments complete all as specified and directed.

M&L for screed bed with CM (1:6) 20mm thick for laying floor tiles complete all as specified and directed.

Providing and injecting chemical emulsion for post constructional Anti termite treatment along external wall where the appron is nor provided using chemical emulsion at the rate of 7.5 liters per sqm of vertical surface of the sub-structure to depth of 300mm including drilling the wall, rodding, plugging the hole with cement morter 1:2 etc complete all as specified and directed.

Providing and injecting chemical emulsion for post constructional Anti termite treatment along the external wall below concrete or masonry appron using chemical emulsion at the rate o f2.25 liters perlinear metre of vertical surface of the sub-structure to depth of 300mm including drilling the wall, rodding and plugging the hole with cement morter 1:2 etc complete all as specified and directed.

Treatment of soil under existing floors using emulsion at the rate of one litre per hole ,300mm apart including drilling the wall, rodding and plugging the holes with cement morter 1:2 etc complete all as specified and directed.

M&L for preperation of old wooden joinery surface surface any description over 10cm in width or girth and applaying one coat of synthetic enamel paint complete all as specified and directed.

M&L for preparation of old plastered wall surface of any description and applying one coat of Oil bound destemper complete all as specified and as directed.

M&L for preparation of old plastered wall surface of any description and applying one coat of white wash complete all as specified and as directed.

M&L for preparation of old plastered wall surface of any description and applying one coat of cement based paint complete all as specified and as directed.

M&L for preperation of levelled surface by surface dressing not exc 15 cm deep and filling with Moorum/red bajri/Soil at the rate of 100 mm average thickness in floors , pavings and in runway shoulders,SGA etc laid in layers n exc 15cm thick spread , levelled and rammed including watering.

M&L for Ploughing of Runway shoulder / SGA by using Motorised Ploughing machine up to a minimum depth of 450mm ,removal of grass & grass roots,cleaning of spreaded mud and dust from runway/ Taxibay/ Dispersals by brushing ,brooming,blowing and washing complete all as specified and directed.

BSK Construction

S.R.M.K Enterprises