RENOVATION OF BISAG N OFFICE AT 5TH FLOOR 5TH CORE OF SCOPE COMPLEX ON LODHI ROAD NEW DELHI AGENCY WORK

Amount

Dismantling wall & ceiling boards of any description as in panelling ceiling, partition, cup boards etc including cover fillets in any surfaces, complete all as specified and as directed

Taking down chowkats or frames including shutters (without taking off shutters from the frame) not exc. 1.5 Sqm each, complete all as specified & directed.

Taking down chowkats or frames including shutters (without taking off shutters from the frame) exc. 1.5 Sqm but n exc 4.0 sqm each, complete all as specified & directed.

Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises, complete all as specified & directed.

Demolition of brickwork or stone/boulder masonry built in cement mortar including all quoins, arches, pillars etc., but excluding ashlar facing, dressed stone work and precast concrete articles, complete all as specified & directed.

M&L Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc and brushing neat cement slurry with 3.0 kg of cement per sq. Metre, complete all as specified and directed.

Taking down cement plaster on brick wall surfaces including recking out joints hacking for key scrubbing down with water etc and removing the rubbish out of Mod Land, complete all as specifeid and directed.

M&L for PCC 1:5:10, nominal mix, type E-2 using 40mm graded crushed stone aggregate as in foundation, filling in sunken floor and mass concrete, complete all as specified & directed.

M&L brick work with old size sub class 'B' bricks , straight or curved on plan exc 6 m mean radius built in cement mortar 1:6, complete all as specified and directed.

M&L brick work with subclass ‘B’ bricks using old size straight on plan exc 6m mean radius in half brick thick walls built in cement mortar 1:4, complete all as specified and directed.

M&L rendering 10 mm thick in cement mortar 1:6 on internal brick/concrete wall surfaces of any description, finished the surfaces even and fair without using extra cement, complete all as specified and directed .

M&L for cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels etc,; and cutting chases for concealed water tubing or concealed conduit wiring etc., and making good, cutting not exc. 10cm girth in concrete block/brick/stone walls, complete all as specified & directed.

M&L for preparation of the newly plastered surfaces of walls applying wall care putty of 1 mm thickness over plastered surface to prepare the surface even and smooth to receive primer and applying one coat primer & two or more coats Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer's specification, complete all as specified and directed.

M&L mild steel TMT bars of 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90mm dia or securing with clips for using in slabs, beams, retaining wall and in foundations, complete all as specified and directed.

All as per Stl item No. 14 above but upto and including 8mm dia in stirrups, spacers and binders as in columns .

M&L for RCC 1:1.5:3, type A-1, using 20mm graded crushed stone aggregate as in beams, cantilevers, bressummers, lintels over 1.5m span and like, complete all as specified & directed.

Use & waste of form work to sides of concrete foundation, footings, bases of columns, rafts and raft beamsand similar work; vertical or to batter for rough finished surfaces of concrete, complete all as specified & directed.

M&L for 2nd class hard wood (Sal/Hollock) plain, solid, straight chowkats/frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue, pinned at joints, with one or more rebates, complete all specified & directed.

M&L for preparation of new or previously untreated wooden surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer, complete all as specified & directed.

S&F Mild steel framed work as in grills, gratings, etc. with ends of bars shouldered and or reveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks and similar work conforming to Fe-290 grade-E-165, complete all as specified & directed.

M&L for preparation of new steel surfaces over 10 cm in width or girth not otherwise described and applying two coats of synthetic enamel paints over one coat of red oxide primer complete all as specified and directed

M&L for preparation of new or previously untreated steel surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer, complete all as specified & directed.

S&F PP-R Gate valves (brass insert) as per requirement of the site outer dia of pipes in 20 mm, complete all as specified and directed.

S&F PP-R Gate valves (brass insert) as per requirement of the site Outer dia of pipes in 25 mm, complete all as specified and directed.

S&F Gypsteel ULTRA/ SHERA/ ARMSTRONG stud partition of 48 mm C Stud (0.6 mm thick having one flange of 34 mm and another flange of 36mm made of GI Steel) placed at 610 mm Centre to Centre in 50 mm Gypsteel ULTRA/ SHERA/ ARMSTRONG Floor and ceiling Channel (0.5 mm thick have equal flanges of 32 mm made of GI steel), which is anchored to the floor and ceiling using suitable anchor fasteners at 600 c/c in center line. Stud and floor channel are crimped together using crimping tool. The boards are to be fixed vertically to the framework with joints staggered to avoid leakage through joints. A Gypsteel ULTRA/ SHERA/ ARMSTRONG Noggin channel of 48 mm width (0.5 mm thick having two flanges of 40 mm each) has to be provided at the horizontal joints of the two boards screw fixed to the studs using Gyproc metal to metal flat head screws . The Junction of the partition with masonry and all penetration through the partition has to be treated with a fire and acoustic sealant. Square and tapered edges of the board are to be jointed and finished to have a flush look which includes filling and finishing with compatable Jointing compound and Joint Paper tape or fibre tape.The junction of the partition with masonry & all penetration through the partition has to be treated with fire & acoustic sealant, complete all as specified and directed.

S&F Gypsteel ULTRA/ SHERA/ ARMSTRONG stud Ceiling of 48 mm C Stud (0.6 mm thick having one flange of 34 mm and another flange of 36mm made of GI Steel) placed at 610 mm Centre to Centre in 50 mm Gypsteel ULTRA/ SHERA/ ARMSTRONG Floor and ceiling Channel (0.5 mm thick have equal flanges of 32 mm made of GI steel), which is anchored to the floor and ceiling using suitable anchor fasteners at 600 c/c in center line. Stud and floor channel are crimped together using crimping tool. The boards are to be fixed vertically to the framework with joints staggered to avoid leakage through joints. A Gypsteel ULTRA/ SHERA/ ARMSTRONG Noggin channel of 48 mm width (0.6 mm thick having two flanges of 40 mm each) has to be provided at the horizontal joints of the two boards screw fixed to the studs using Gyproc metal to metal flat head screws . The Junction of the ceiling with masonry and all penetration through the partition has to be treated with a fire and acoustic sealant. Square and tapered edges of the board are to be jointed and finished to have a flush look which includes filling and finishing with compatable Jointing compound and Joint Paper tape or fibre tape.The junction of the partition with masonry & all penetration through the partition has to be treated with fire & acoustic sealant, complete all as specified and directed.

S&F 50mm thick Rock wool insulation having a density of 48Kg/CMT for opaque partitions as per detail dwg. Cost to include RP Tissue wrapping, complete all as specified and directed.

S&F 12mm thick MDF Board skinning on existing frame work using 19mm screws at every 300mm center to center. The MDF skinning finished as in partition, complete all as specified and directed. Make: Century Ply/ Green Ply/ Crosta Panel

S&F 12mm thick MDF Board skinning on existing frame work using 19mm screws at every 300mm center to center. The MDF board finished as in ceiling, complete all as specified and directed. Make: Century Ply/ Green Ply/ Crosta Panel

S&F Laminate paneling formed out of 1mm thick approved laminate with 4mm thk MDF Backing fixed over existing MDF board, complete as per instruction of the Architect's. cost to include providing and fixing 5mm Aluminium " T "Channel in Vertical position, complete all as specified and directed. Make: Greenlam/ Royale Touche/ Century

S&F Laminate in false ceiling formed out of 1mm thick approved laminate with 4mm thk MDF Backing fixed over existing MDF boards, complete as per instruction of the Architect's. Cost to include provididng and fixing 5mm Aluminium " T "Channel in ceiling position, complete all as specified and directed. Make: Greenlam/ Royale Touche/ Century

S&F Glass panelling formed using 6mm thick Lacqured glass with existing GI Frame work & 12mm thk MDF backing, complete as per the detailed dwg or the instructions of the Architects. Consider 2 - 4 mm gap between each glass panels with aluminium "T" section, complete all as specified and directed.

S&F Senses akustik+ 9mm thick felt panel for reducing and controlling reverberated noise for wall & ceiling application with an NRC of 0.50, panel composition of 100 % wool felt, which is free of harmful substances. CII green pro certified , class-2 green building products, size of panel 1200mm x 2400mm Fixing as per manufacturer guidelines. including wastage, weight 2400 g/sm Density 2.3 kg/m3 fire retardant properties AS/NZ 3887 Group Classification 3 Smoke Development Index 7- AS/NZ 3837 Group Classification 3 Color Fastness to Light ISO 105-B02 1994 (Grey Scale 1 to 5) 3, complete all as specified and directed.

S&F of ELD MOSS wall - Raindeer Natural Moss preserved on existing 12mm thick Ply or MDF board with 30mm thick Moss to cover the area as per Architects Design and pattern or with color combination Moss Greenwalls works best when used indoors with controlled air conditioning, humidity levels at 25% or higher and out of direct sunlight. Moss Specifics Light Weight – Preserved moss is very light weight and does not require extensive support infrastructure. Very Customizable – Able to be used in tight corners and curves, while also incorporating color/texture diversity in the design. No Watering Required – No irrigation required. ADA Compliant – Protrudes approximately 1” from the existing wall surface Interior Acoustic Control – Captures interior sound movement and echo. Low Maintenance, Inexpensive – Brings green to interior environment, complete all as specified and directed. Make: WeDecor8/ Greenopia/ myBageecha

S&F of Slim Glass partition of 12mm Toughened Glass using dormakaba Alexa System-45 Frames to a height of maximum 3m or as per drawing.The Fixed glass to be fixed using dormakaba Alexa BP45 Profiles at Top & Bottom & Alexa SP45 at sides. The profile size to be 45x25MM to be fixed on to the floor/wall/ ceiling as per the architect design. dormakaba Alexa H Junction profile to be used at all Glass to Glass vertical joints, 90 Deg L Junction Profiles and T Junction profiles necessary as per design.In case of Glass overall panel Alexa MP45 & BP45 Overpanel Profile to be used.In case of Open glass edges EP45 End Profile to be used. The Alexa profiles shall be suitable for Glass thickness of 10/12/13.52mm.The Profile shall be matt natural anodized, the Profile Manufacturer to supply all the necessary clips, seals and fixing accessories for the system. All Profiles to be with 2 mm Gauge thickness excluding 20 Micron of Anodizing. Approved Manufacturer : Profiles/Frames: dormakaba Glass : Saint Gobain/ Asahi/ Modiguard" Insulation: 50 mm thick (Density -64 Kg/m3) Rockwool mat is to be placed in the cavity of the partition. Jointing and Finishing : Finally edges of the Boards are to be jointed and finished so as to have a flush look which includes filling and finishing with All purpose jointing compound and 48 mm wide self-adhesive fibre tape. Cement Primer (Oil based) to be provided on entire surface before putty/ painting. Note: A Horizontal Intermediate channel is to be provided for every 3 feet level on both sides, if the partition height exceeds the board length to provide edge support to the board, complete all as specified and directed.

Supply and Installation of CUBICLE PARTITION TOILET MODULAR CUBICLE as per following specifications:- Athena Lite Series (SS + Aluminium) Shade - Thickness of compact laminate board = 12mm, Overall Height of cubicles = 2105 mm (including a gap of 150 mm from the ground) Accessories 1. Alluminium Wall bracket for H-top rail 2. Aluminium U-channel 3. SS Door Knob 4. SS Privacy thumb turn with occupancy indicator. 5. SS Hinges with cover 6. SS Coat Hook 7. Alluminium Door Stopper channel 8. Rubber door stoper lining 9. U Channel -SS Make: Merino Industries Ltd/ Cubiloo/ Bulwark

S&F Glass Urinal partition Chamfer Size 450x900mm made of 12mm thick heat strengthen glass with both side acid frost finish, cut & finish, fixed on wall using SS 304 Heavy "L" bracket with insert, complete as specified and directed.

M&L for providing PMM (Polymer modified cementitious mortar) :- (i) Dry sub strate surface and free of debris & dust (ii) Applying Epoxy bond coat on the sound substrate using approved spray machine & ensuring that no pin holes are visible. (In case pin holes are still visible after a coat, a second coat shall be applied to ensure absence of pin holes). (iii) Immediately after application of epoxy bond coat as above apply PMM (Polymer modified cementitious mortar) of 25 mm thickness. Note : Application of PMM shall be preferably be in coats of appx 10mm thickness. PMM work shall be executed in fairely rapid successions so as entire work is completed with in 30 mins). PMM shall be pre packed ready to use. (iv) PMM surface to be moist cured for three days followed by air curing in temperature as recommended by manufactuer complete all as specified and directed.

M&L for preparation of old decorated surface (plastered or unplastered) of walls by complete removal of existing treatment by mechanical grinder and applying cement base wall care putty of 1 mm thickness over plastered surface to prepare the surface even and smooth to receive primer and applying one coat primer & two or more coats Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete all as per manufacturer's specifications.

M&L for preparation of the newly or old surfaces of ceiling applying putty of 1 mm thickness over plastered surface to prepare the surface even and smooth to receive primer and applying one coat primer & two or more coats Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete all as per manufacturer's specifications.

S&F in position Fire Rated Metal door with pressed steel frame of 46 mm thick and shutter made with 1.25 mm thick galvanized steel sheet as per manufacturer’s details and as mentioned in the drawings including fixing iron mongery etc of MPP System Schroders make. This includes providing and fixing brush steel finished iron mongery like Ball bearing Hinges, Mortise Locks, Dorma Handles, Push Plates, Bolts, Door Closer, panic bar etc. (Dorma make) as indicated in the detail drawings and all surfaces of doors shall be finished with 2 coats of Fire rating paint over a coat of primer to achieve the fire rating as indicated in the detail drawings. The door finished Fire retardant polish, steel pressed shutter with 2 Hour Fire rating of Single Shutter and vision panel with Dorma Panicbar with built in Buzzer battery operated complete as per design and instructions opening size: - FD - 1200mm X 2400mm (With vision panel of 2 Hrs Fire Rated Glass of 11mm thk) {FIRE DOOR - WITH PANIC BAR 2HR. FIRE RATED DOOR}, complete all as specified and directed. Make: Avians/ Nitsui India Pvt Ltd/ Shakti Hormann/ Bhawani Fire Protection Pvt ltd/ Radiant Safe Doors/ Acodor

S&F 60 mm thick glazed fire resistant partition for 120 min Fire Rating confirming to made out of 60mmx 70 mm of 1.6 mm thick galvanized steel sheet as per test evidence suitable for fixing fire rated glass for 120 min of both integrity & radiation control (EW 120) & minimum 20 min of insulation (EI20). The profile has to be fixed to the supporting construction by means of anchor fasteners of size M10x80, every 150 mm from the edges and every 500 mm (aprox) C/C. Linear measurement of frame shall be fitted with wool insulation of density 96 kg/Cum and finished with approved fire resistant primer of powder caoting of not less than 30 micron in desired shade as per NBC 2016, IS16231 (part-3): 2016, complete all as specified and directed. Make: Avians/ Nitsui India Pvt Ltd/ Shakti Hormann/ Bhawani Fire Protection Pvt ltd/ Radiant Safe Doors/ Acodor

S&F 60 mm thick glazed fire resistant door shutters of 120 min Fire Rating confirming to IS:3614 (Part II) or EN1634-1:1999, tested and certified as per laboratory approved by Engineer-in-charge, with suitable mounting on door frame, consisting of vertical styles, top rail & side rail 60 mm x 60 mm wide and bottom rail of 110 mm x 60 mm made out of 1.6mm thick G.I. sheet (zinc coating not less than 120gm/m²) duly filled mineral wool insulation having density min 96 kg/m³ and fixing with necessary stainless steel ball bearing hinges of size 100x89x3mm of approved make, door handles, suitable locking device (Anti theft system) including applying a coat of approved fire resistant primer or powder coating not less than 30 micron etc all complete as per direction of Engineer-in-charge {GLAZED FIRE DOOR - 1800 X 2400mm 2HR. FIRE RATED DOOR}, complete all as specified and directed. Make: Avians/ Nitsui India Pvt Ltd/ Shakti Hormann/ Bhawani Fire Protection Pvt ltd/ Radiant Safe Doors/ Acodor

S&F in position frameless glass door shutter with 12mm thk toughened clear glass portion with a stainless steel patchVfittings at top and bottom member with approved glass door lock,Floor spring including approved S.S paired handle of approveddesign and size with other side connector as per drawing with necessary glass fitting. Rate to include complete in all respect as per direction including floor spring, SS Paired handles, Lock and patch fittings, complete all as specified and directed.

S&F in position sliding frameless glass door shutter with 12mm thk toughened clear glass portion with a stainless steel patch fittings at top and bottom member with approved glass door lock, including approved S.S paired handle of approved design and size with other side connector as per drawing with necessary glass fitting. Rate to include complete in all respect asper direction. incl SS Paired handles, Lock and patch fittings, complete all as specified and directed.

S&F in position phenol bonded homogeneous 35-40 mm thick flush door shutters of approved quality and make, non decorative type core of block board construction with internal frame of 1st class hard wood and well matched 3mm commercial ply veneering with vertical grains including providing and fixing 4 nos. 125mm long and 3.5mm thick SS hinges, 2x SS Door handles minimum 200mm long, Mortise Lock shutter to be finished with 6 mm thick melamine polished teakwood liping all around and the surface finished with 1.5mm thick laminate on both sides of shutters with synthetic adhesive as per specifications, complete all as specified and directed.

M&L for 15 mm thick Full body coloured vitrified tiles of size 800x 2400 mm of approved shade flooring over and including 20mm thick screed bed in cement mortar 1:6, joints shall be filled by using Dr. Fixit epoxy tile grout or equvalent of pigment to match with the shade of tile, complete all as specified and directed

M&L for 15mm thick coloured vitrified Matt finished full body decorative type tiles of size 600 mm x 600 mm of approved make, shade and pattern for flooring in required position laid on a 15mm thick bed of 1:4 cement mortar, including neat cement float, filling joints with coloured matching neat cement slurry, curing and cleaning etc. complete all as specified and directed.

M&L for Walls ceramic coloured tile, area of each tiles exceeding 0.42 sqm but not exceeding 1.00 sqm of approved make and approved sample in pattern as per detailed drawings in adhesive chemical paste. The rate should be inclusive of surface preparation, cleaning joints and grouting them with approved white cement paste with pigmented additives to match shade of the tile. Tile shall be free from any other colour & size variation. The edges of the tiles should be straight and without bends & tiles shall be free of any variation in colour or texture. Cost to include required adhesives for laying. Cost to be include any type of wastages during laying. Tiles can be laid with providing spacers up to 6mm also in between tiles. Necessary epoxy grout to be filled in spacer gaps after laying of tiles complete all as specified and directed.

S&F 50mm ht. approved extruded aluminium skirting with Rubber strip fixed over masonry wall /opaque partition to proper line & level. with approved Screw, complete as per manufacturer's specifications, complete all as specified and directed.

S&F 300mm high raised False access Flooring over existing RCC slab/flooring of support, inclusive of support framework- avg. 600 x 600 x 30 mm sandwich cement tiles flooring encased in precoated MS sheeting of egg-crate type closed profile on the bottom & antistatic vinyl skin of approved micron thickness and colour over flat precoated MS top sheet. Edge-to-edge flush tiles to be fixed on anti-corrosive MS Alloy pipe studs min. 25 mm dia. with receiving brackets, tie-members & bottom pressure pads of the same alloy material, bolted & fixed complete. support studs to be have height adjustable mechanism to an approvable range. Item to include trap door, all fabrication for steps or ramps in same material including treads and risers, all hardware, all accessories, tools, labour, lift till 20mts. with all cleaning complete etc., installed complete as per standard specification. making mock-up for approval of Architect/Engineer incharge. The system shall be able to withstand a UDL of 1350 kgs/sq.mt. and a point load of 450 kgs. The understructure should be able to accept a pedestal Axial load of 2200 kgs. The work to be completed as per manufactures instructions and as specified and directed.

M&L for 18-20mm thick coloured granite stone work Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite, complete all as specified and directed.

S&F 12 mm thick (+/-2mm) corian top platform with 75 mm facia with joint less bend / nosing / rounding on MS supporting brackets duly painted and base as 19mm BWP ply as required as per the detail drawing etc., cutting for basin opening, sealing all crevices with silicon sealant, etc., complete all as specified and directed.

S&F False ceiling of 12.5mm thick square/tapered edge Gypsum board conforming to IS : 2095, at all height & levels, as per approved drawing ,including providing steps as per design and pattern with complete GI ceiling suspension system. GI perimeter channel of 20x28x30x0.5mm is fixed to the wall/partition with impact anchor at not more than 600mm c/c. GI Ceiling angle of 25x10x0.5mm is fixed to the ceiling with soffit cleat of 27x37x25x1.6mm and with the help of Rawl plug 8dx45mm. The other flange of soffit cleat is fixed to GI ceiling angle with 12mm hex bolt and nut. The spacing for GI ceiling angle shall be 1220 c/c. GI Intermediate channel 15x45x15x0.9mm shall be fixed to ceiling angle at 1220 c/c with metal to metal screw. 80x26x0.5mm ceiling section shall be fixed at 450mm c/c. The ceiling section shall be fixed to intermediate channel with the help of connecting clip of high carbon spring steel wire and in direction perpendicular to intermediate channel at approx. 450mm c/c. The Gypsum board is fixed to the horizontal grid with self driven screws and joints are finished with putty & tape and one coat of primer. The joints to be finished with 48mm wide fibre tape to provide seamless finish. Work to include making and finishing of recesses for lighting fixture, preparing the board to take paint finish , providing cutting for trap door of required size for service access, Al. powder coated HVAC grills as per approval by Architect/HPCL, necessary coves,recesses as per design drawing, including cutting for access doors,sealing the joints with Air Drying Joining Compound or equivalentsealing materials, with flush bonded/ screwed securing of the hatch using a clip-lock mechanism that is integrated in the frame and concealed. Item to include all accessories, fitments, men & material & lift up to 50 mt., correct installation procedure, trap door cutting and necessary cutting in False ceiling strictly with unit template and finishing, necessary scaffolding, cleaning etc. complete. The finished surface including the cove surface will be measured for payment. Cove shall also be measured in sqm only. Note :- No extra will be paid for ceiling drops and it will be considered as flat ceiling and if there is projected drop ceiling curved as per design in different level it will also be paid as additional. No extra will be paid for light cutings. No extra will be paid if it is required channel/angle for additional supports for ceiling, continuous grill, diffusers, trap door for ductable unit, cassettes unit etc. Gypsum board shall be fitted and finished with base coat of putty, one coat of primer and 3 coats of plastic paint as per requirement and rate shall be inclusive of same.

(MODULAR GRID CEILING ( MINERAL FIBER TILE ) 1200mm X 300mm) Providing & installing Commercial type suspended modular ceiling consisting of General requisites Grids width: 15mm Silhouette with black revel finished in approved shade. The main Runners & cross Tees to have "stab" installation system made of corrosion-protected high tensile steel OR approved equivalent. Tile specification : Tile type: Lay-in ceiling type Tile size: 1200mm X 300mm X 15mm thk. Edge detail: Microlook Edge Light reflectance: up to 0.84 ( 84% ) Humidity resistance: 99% RH Color: White similar to RAL 9010 Surface burning characters: Class1, BS 476:Part 7:1987 Smoke Developed: 0 & Flame Spread = 5 as per UL Thermal conductivity: 0.052 - .057 W/mk NRC: 0.55 / 0.60 Thikness/Weight : 4.5 Kg/m2 CAC: 34 dB Surface Pattern : Plain with random perforations Ceiling Suspension System Proprietary supplied ceiling suspension system to consist of 2mm or 3mm GI suspension rod/wire with adjustable adjustable threaded "J" bolt of 3mm dia securely affixed to structural ceiling using soffit angle fixing bracket and 10mm dia hook type anchor fastener. Ceiling suspension system to be fixed at interval (grid) of 1200mm in both directions. Proprietary supplied Grid System to consist of Main Runners @ 600mm and joined by Cross Tees @ 600mm to form overall grid opening of 600mm x 600mm. Additional cross tees are to be placed where appropriate for light fixtures, AC diffusers. The grid system used shall be hot dipped galvanized steel sections, with exposed surfaces chemically cleaned and capped prefinished in high - gloss polyester enamel with two coat system on cold rolled steel. Grid member sizes Main runners : 15mm X 40mm X 0.38mm Cross tees : 15mm X 40mm X 0.38mm Perimeter section : 14mm X 20mm X 0.43mm False ceiling will be measured on horizontal plane only. Horizontal plane measurements are to be inclusive of all vertical drops, edge moldings, fascias, etc, complete all as specified and directed.

S&F of suspended acoustical Hanging Baffles made of Wooden Strips NRC Value –0.5- 0.80 NRC. The baffle made out of 5mm thick and 25mm wide wood strip on both faces fixed on wooden batten. Rockwool of 48 Kg/m3 density confirming to IS 8183 , tissue fiber paper laminated filled in between wooden strips as acoustic insulation to achieve desired NRC value. The Aoustic Wooden Baffles are square or V in shape as per architects approval. Size of the Baffles 1200x150x50mm thick, distance in between two baffles will be 150mm . Can be Installed with Hanger Wire or Thred Rod. The Baffles to be suspended individually using the Unistrut Channel with cable adjuster or locking Clip tied by Thred rod or Hanger Wire kit comprising of hanger wire/cable adjuster/cable finishing hook.Sample to be submitted from all the approved make or equivalent for approval of engineer in charge prior to the installation, complete all as specified and directed. Make: Aural Exchange/ Ecotone Acoustic Pvt Ltd/ Manacoustix/ Techno Acoustic

M&L for preparation of existing surfaces to receive waterproof, slab surface should be cleaned to remove dirt, dust, laitance, soft mortar and all loosely adhered particles. The slab should be Pre-wetted to make it saturated and free water to be drained using a dry cloth. All Pipe inserts must be installed prior to the application of waterproofing system on the slab. Applying a 2 coats of cement slurry with waterproofing compound (proportion as per manufacturer). The coat has to be extended on the masonry wall at least 3ft above finished floor level. Laying of sound brick bat coba, AAC Block coba (upto 200mm thk./as per site requirement) at required gradients with proper slope. Proper gap should be maintained between the brick bat with staggered joints. Fill joints with cement mortar 1:4 along with water proofing compound (dosage as per manufactures). Finish AAC block coba with joint less water proofing screed (Cement: Sand Mortar of 1:3) admixed with water proofing compound (dosage as per manufacture’s recommendation). The surface has to be finished smooth and checked for slope check. Also ensure proper finishing around Nahani traps/inserts. All plumbing inserts and drainage pipes are to be checked for joint leakages, complete all as specified and directed.

S&F frosted film with approved art work, cut using digital plotter. Self-adhesive, bubble-free installation to be done on make over clear glass panes in pattern/Design as per drawings, complete all as specified and directed.

S&F Pelmet for blinds, made out of 18mm thick MDF Boards, exposed edges of the pelmet shall be finished in approved Laminate. The pelmet shall be in reversed "U" shape and shall be 200mm wide and up to the nearest Horizontal Mullion. The rate quoted shall be including fixing the pelmet with GI support @ 1200mm c/c anchor bolted to the structural ceiling etc., complete as per detail drawings. Factory pressed Lamiante, complete all as specified and directed.

S&F Vertical venetian blinds of approved shade. The blinds to be fixed and commissioned as per manufactures specification, complete all as specified and directed.

S&F storage 600mm deep formed out of 19mm thick MDF / MDF finished in 1mm thick approved laminate consisting of storage with shutter, & 1mm thick approved laminate inside. The shutter of the storage shall be formed out of 19mm thick MDF finished in 1mm thick approved laminate on the external side. with 1mm thick approved laminate on the inside mounted over spring loaded auto closing hinges of approved make, tower bolt. The Strogae to accomodate Shelf made of 19mm thk MDF finished with approved laminate as per the dwg .The exposed edges of the storage shall be lipped using approved timber beading formed to shape melamine polished, complete as per detail dwg. & Architects instruction. Storage to be complete with hardware installed as directed to consist of the following. Shutter to have Soft-closing spring loaded hinge of approved make installed strictly as per manufacturers guidelines. All necessary tools should be strictly used for correct installation of hinges. Each set of shutters to be provided with 1 Nos. chrome finished multi-purpose lock of approved make, 75mm medium sized stainless steel tower bolt, 1 Nos. heavy duty SS ball catch, 100mm C type brushed SS handle, complete all as specified and directed.

S&F low height storage cabinet of height 850mm and depth 600/ 750mm formed of 19mm HDF formwork/carcass finished with 2mm thk approved Acrylic Sheet . Shutter of storage unit to be made of 19mm thk HDMR finshed with approved colour 2mm thk Acrylic Sheet. All Handles and Drawers will have Aluminium Grip Profile ( Artical No : 126.14.901) of Haffle Make. All Drawers and Tandom Boxes will have Anti-strip matt form Haffle. Counter top will be finished with 12mm thk approved Solid Acrylic Surface , Which includes back splash of 250mm ht. Complete as per the drawing, Pantry counter to include 4nos of Dust Bin of capacity 30 lit SS finish, complete all as specified and directed.

S&F storages 450mm depth formed out of 19mm thick commercial MDF finished in 1mm thick approved laminate. The top shall be formed out of 19mm thick commercial MDF finished in 1mm thick approved laminate, exposed edge of the table shall be lipped using approved timber beading formed to shape melamine polished. The shutter of the storage shall be formed out of 19mm thick MDF, finished in 1mm thick approved laminate mounted using Auto closing hinges of approved make. The shutter shall be provided Finger Grooves for opening. The storage shall be provided with shelf formed out of 19mm thick commercial MDF finished in 1mm thick approved laminate on both sides mounted over SS adjustable pins of approved make. Provision for Cove Lighting to be done as per the dwg and instructions of the Architect. All internal surfaces to be post laminated with 0.8mm thick matt finished laminate of approved shade. All exposed surfaces (underside, topside to be finished with 1mm thick decorative laminate of approved shade. Storage to be complete with hardware installed as directed to consist of the following. Shutter to have auto-closing spring loaded hinge of approved make installed strictly as per manufacturers guidelines. All necessary tools should be strictly used for correct installation of hinges. Each set of shutters to be provided with 1 Nos. chrome finished multi-purpose lock of approved make, 75mm medium sized stainless steel tower bolt, 1 Nos. heavy duty SS ball catch, complete all as specified and directed.

S&F the Planter box shall be formed out of 12mm thk MS rod horizontally vertically fixed to the floor using appropriate base plate and anchor fastners to hold the with stand of planter box & open ledges provision of different module for storage & Planter box. All MS work shall be spray enamle painted over a coat of zinch chromate primer as per the approved make & shade. Module 01 : Planter box shall be 450 mm deep incl shutter, shelve, autoclosing hinges and handles formed out of 18mm thick HDF, sides shall be formed out of 18mm thick HDF. The boxing shall be cladded with laminate on all sides.The top to be lipped with approved 2mm thk edge binding complete as per the drawing etc complete as per Architect's instruction. cut outs shallbe made for plants & GI tray in the bottom of the plants as per the architects instruction. Each Planter Box shall have a 3 plants of 1 ft height plants complete all as specified and directed. Note:- Front superfacial area shall be measured.

S&F 150mm thick AAC block masonry walls as specified in cement mortar 1:6 using precast blocks of 400 x 150 x 200mm size with minimum crushing strength of 35 kg/sq. cm (as per IS:2185) for construction with necessary scaffolding, staging, striking and raking out joints to at least 10mm depth, including RCC binders in mix proportion 1:2:4, 75mm thick reinforced with 2 nos. of 8 mm dia Fe 415 bars with 8 mm dia TOR steel tie bars at 300 mm c/c, RCC binders to be at every 1 meter interval from floor level complete all as specified and directed.

S&F signages for cabins, meeting rooms, toilets, pantry doors etc.in brushed steel plate or any other finish with text of approved style and font as per instructions, complete all as specified and directed.

S&F vitreous china EWC wall mounted with C.P.bolts, nuts C.I chair or other hanging arrangement, solid plastic seat with lid, C.P brass hinged rubber buffers, complete including cutting and making good the walls and floors wherever required ROCA or approved equivalent), complete all as specified and directed. Make: ROCA Cat Part No.RS346248000, KOHLER Cat Part No.727571 N-O & SKU19080IN-SS-O, JAQUAR Cat part No. ARS-WHT-39961BIUFSMTL

S&F Concealed Flushing Cistern with dual flush Actuator, flush-stop function, noise less float valve and fast filling action with all component parts of high quality complete including fixing frame and set, complete all as specified and directed. Make: ROCA Cat Part No.A890077020, KOHLER Cat Part No.K263531N-P-NA, JAQUAR Cat Part No.JCS-WHT-2431FS

S&F Wash hand basin vitreous china of counter top lavatory, specially fabricated brackets painted white, 32mm C.P.cast brass bottle trap and connection pipe to wall with C.P. wall flange and rubber adopter for waste connection complete, including cutting and making good the walls wherever required, complete all as specified and directed. Make: ROCA Cat Part No.RS-32753000, KOHLER Cat Part No.77171IN-O, JAQUAR Cat Part No. JDS-WHT-25931

S&F White vitreous china battery based infrared sensor operated urinal of size 295 x 325 x 575 mm having water inlet from back side including fixing to wall with suitable brackets, CP bottle trap, connection pipe to wall with C.P flange and sensor all as per manufacturers specification and direction complete all as specified and directed. Make: Hindware, Jaquar, ROCA

Blank

S&F stainless steel sink with drain board with C.I. brackets, duly painted white 40mm C.P. waste,C.P. brass chain and rubber plug, 40mm C.P cast bottle trap with connection pipe to wall and C.P. wall flange, rubber adapter for waste connection complete including cutting and making good the walls wherever required 1065x510x200mm, complete all as specified and directed.

S&F Fancy type 15mm dia chromium plated quarter turn fancy type wall mixer hot & cold with long swan for kitchen sink fixing and connection to pipes, complete all as specified an directed. Make. Jaquar CAT Part No.FLR5309N,CERA CAT Part No.F1003501, Hindware CAT Part No.F570027

S&F 15mm dia. CP brass angle valve with all nuts, washer with CP brass flange complete, including cutting and making good the walls, wherever required, complete all as specified and directed.

S&F of Container - Polycarbonate ABS Casing & Capacity: 1100 ML. Body is drawn, one-piece, 2CM Sensing range, seamless construction. Back plate has mounting bracket attached. Battery operated sensor (4 X AA Duracell) based soap dispenser. Touch free Infra red activation type top filling for wash basin fixing with necessary screws etc., complete all as specified and directed. Make: ROCA, JAQUAR, KOHLER

S&F Decorative towel ring, brass chromium plated fixed with and including chromium plated brass screws and wooden/plastic cleats including cutting and making good the walls wherever required, complete all as specified and directed. Make: ROCA, JAQUAR, KOHLER

S&F CP cast brass double coat hook fixed to wooden / PVC cleats with C.P. brass screws, complete all as specified and directed.

S&F Airpurifier / aerosol dispenser in ABS body with programmable controls, fixed to wooden cleats with C.P brass screws, complete including cutting and making good the walls wherever required, complete all as specified and directed. Make: ROCA, JAQUAR, KOHLER

S&F CP Health Faucet (Hand Operated) with lever controlled and 1 meter Flexible Tube connection with C.P. Wall Hook, complete all as specified and directed. Make: ROCA, JAQUAR, KOHLER

S&F 6mm thick beveled edge mirror with teak wood beading (Mirror of approved quality and as per specifications) with 6mm thick asbestos plain sheet ground fixed with C.P. brass screws and washers etc. complete. 700 x 500 mm, complete all as specified and directed.

S&F C.P. Brass toilet paper holder, including cutting and making good the walls wherever required complete all as specified and directed. Make: ROCA, JAQUAR, KOHLER

S&F straight / offset type flexible single body push fit type WC pan connector with inlet ring and integral single mould sealing fins made of flexible EVA body to be fixed with manufacture supplied grease, including rubber bush / adaptor for use with C.I pipe as supplied with the pan connector, complete all as specified and directed.

S&F Sensor Faucet to table top Wash basin including suitable CP connection ,complete all as specified and directed. Make: ROCA, JAQUAR, KOHLER

S&F CP Grab Bar with wall flanges 600 mm fixed to wooden cleats with C.P. brass screws complete in all respects, complete all as specified and directed. Make: ROCA, JAQUAR, KOHLER

S&F Sound insulated Polyproplene piping (PP) system as per ON EN 1451-Part 1 & EN 12056 Part 1-5 , DIN 1986-100 - class B & D, with 3 layer pipe made of PP/PP-MV/PP in Blue Ral 5014 colour (free from halogen, cadmium and heavy metals), push-fit type, food safe, having high impact and stiffness, offering sound levels of not more than 16 dBA as per DIN 4109 at a flow rate of 4 l/s and having pipe ring stiffness of 6kN/m2 or more as per EN ISO 9969, density and elongation of pipe not more than 1.25gms/cm3 and 0.05mm/m0K respectively, tensile strength to be > 24 N/mm2, cost including all necessary fittings in blue colour, fitted with factory fitted lip ring Pipes and fittings including supporting system GI clamps / hangers/G.I structure supports with angle & fastner as required. including cost of core/hole cutting and making good the walls and floors wherever required 100mm dia, complete all as specified and directed.

S&F sound insulated Polyproplene piping (PP) system as per ON EN 1451-Part 1 & EN 12056 Part 1-5 , DIN 1986-100 - class B & D, with 3 layer pipe made of PP/PP-MV/PP in Blue Ral 5014 colour (free from halogen, cadmium and heavy metals), push-fit type, food safe, having high impact and stiffness, offering sound levels of not more than 16 dBA as per DIN 4109 at a flow rate of 4 l/s and having pipe ring stiffness of 6kN/m2 or more as per EN ISO 9969, density and elongation of pipe not more than 1.25gms/cm3 and 0.05mm/m0K respectively, tensile strength to be > 24 N/mm2, cost including all necessary fittings in blue colour, fitted with factory fitted lip ring Pipes and fittings for wash basin, urinals, indirect waste, Bath Tub etc dia of pipe (40 mm OD), complete all as specified and directed.

All as per Srl item No 87 above but dia of pipe (50 mm OD)

S&F Polyproplene P floor trap with 2/3 inlets of 40/50 mm size and one outlet of 110 mm size, inlet connection extension pipe piece and setting in cement concrete 1:2:4 mix complete including cost of cutting and making good the walls and floor complete where ever required 110 mm inlet & 110 mm outlet, complete all as specified and directed.

S&F floor drain (FD) with 50mm/40mm outlet and one 40mm inlet for waste, with SS grating (adjustable height), having 50mm water seal and in-built NRV (McAlpine mrfg3 ). Providing and fixing floor drain (FD) with 100 mm inlet and 50mm outlet including SS grating, complete all as specified and directed.

S&F Polyproplen door cleaning piece male threaded joint with socket soil pipe/waste pipe of Polyproplen pipe as required. (Both for Pipes running under floor )

S&F Polyproplen clean out Plug (FCO & COP) with suitable insert keys for opening, male threaded joint with socket soil pipe/waste pipe of Polyproplen pipe as required. (Both for Pipes running under floor & along ceiling level), complete all as specified and directed.

M&L for cement concrete 1:2:4 mix (1 cement : 2 coarse sand: 4 stone aggregate 20mm and down gauge) 75mm in bed and pipe. For 100mm, 75mm and 50mm dia pipes under floor including centering & shuttering wherever required, complete all as specified and directed.

S&F 125mm dia Bronze Chrome plated ring and Grating with 2 stainless steel screws, ring to be embedded in floor with sealant, complete all as specified and directed.

S&F P - Trap For sinks & wash basin , with horizontal outlet, quality controlled in accordance with DIN EN 274,(1 1/2" X 40mm) Body Made of PP (Poly Propylene) White in Colour, complete all as specified and directed.

Supplying and laying of CPVC 20mm OD pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified complete with fitting as required, complete all as specified and directed.

Supplying and laying of CPVC 25 mm OD pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified complete with fitting as required, complete all as specified and directed.

Dismantling, Packing, including transportation and Reassembly charges alongwith Packing Material of the following items :- (Dismantling to be done from Bisag office Jor Bagh Delhi & Reassembly to be done at Bisag Ofice, Scope Complex, 5 core, 5th Floor, Lodhi Road, Delhi) Executive Table with one side Pedestal (Royal Koas) with Bubble Wrap - 2, Reception Table (Royal Koas) with Bubble Wrap - 1, Computer Table Executive (Small Almirah) inclusive (Royal Koas) with Bubble Wrap - 2, Long Almirah inclusive (Royal Koas) with Bubble Wrap - 2, Revolving Chair (Reception) (Royal Koas) with Shrink Wrap - 1, Revolving Chair (Executive) (Royal Koas) with Shrink Wrap - 6, Revolving Chair (Boss) (Royal Koas) with Shrink Wrap - 2, Center Table (Godrej) with Bubble Wrap - 4, Conference Table 21 Seater with Bubble Wrap - 1, Modular Workstation (Godrej) with Bubble Wrap - 55, KBPT (Godrej) with Bubble Wrap - 55, Pedestal (Godrej) with Bubble Wrap - 55, CPU Trolly (Godrej) with Bubble Wrap - 55, Leathorite Chair (Conference ) (Godrej) with Shrink Wrap - 26, Chairs for Workstations (Godrej) with Shrink Wrap - 55, Conference table 8 Seater (Godrej) with Shrink Wrap - 8, 3 Seater Sofa (Godrej) with Shrink Wrap - 4, 1 Seater Sofa (Godrej) with Shrink Wrap - 2, complete all as specified and directed.

S&F Anti Pigeon Spikes of Polycarbonate 100 mm in width and 100 mm in height using adequate Defender Silicone Adhesive Spike fixing Glue, complete all as specified and directed.

M&L for best quality vinyl/lamm costomised graphic wall paper on wall applying with necessary adhesive including matching corners and angles, complete all as specified and directed.

Description of Work / Item(s)

Amount

INTERNAL ELECTRIFICATION M&L for point wiring with PVC insulated unsheathed multi stranded FRLS type copper conductor cable of size 1.5 Sqmm 1100 V grade, IS -694 marked including one run of PVC insulated unsheathed multi stranded FRLS type copper conductor cable of size 1.5 sqmm as earth continuity conductor connected to common earth dolly in and including PVC concealed conduit medium grade ISI marked of suitable size and its accessories including provn of new factory made pressed steel modular switch/terminal box of suitable size and new modular front & back plates of approved colour/model of suitable size for housing the modular switches, sockets, fan regulators for the following :- Make of PVC cable : Havells, RR KABEL, KEI

(a) One light/ ceiling fan/ exhaust fan /bell/ buzzer point controlled by one no, one way 6 Amp switch.

(b) One three pin 6 Amp socket outlet point controlled by one no, one way switch on same board.

(c). One three pin socket outlet 6 amps point controlled by one no, one way switch on independent board.

M&L for Point wiring with 2.50 sqmm, single core, PVC insulated, unsheathed FRLS cable, 1100 volts grade, IS -694 marked, with multi stranded copper conductor and earth continuity copper conductor cable of 2.50 sqmm connected to common earth dolly drawn through and including rigid PVC concealed conduit, medium grade ISI marked of suitable size alongwith fittings and accessories, fixed /laid/concealed in walls/ceilings including cutting chases and making good to walls, floors etc, and also including provn of new factory made pressed steel modular switch/terminal box of suitable size and new modular front & back plates of approved colour/model of suitable size on independent board, complete all as specified and directed. Make of PVC cable : Havells, RR KABEL, KEI

S&F Modular switch 6A, 1 way switch, 1 module, complete all as specified & directed. Make : Legrand Arteor Cat Part No. 573400, Schneider Cat Part No.IN8401, MK Cat Part No.K34881N

S&F Modular switch 1 way 16A, 1 module, complete all as specified & directed. Make : Legrand Arteor Cat Part No 573410, Schneider Cat Part No.E-8432/1-OS, MK Cat Part No. K34891N.

S&F Modular socket 6A, 2/3 pin combined, 2 module, complete all as specified & directed. Make : Legrand Arteor Cat Part No 573470, Schneider Cat Part No.IN8426, MK Cat Part No.K34382

S&F Modular socket 6A/16A, 2/3 pin combined, 2 module, complete all as specified & directed. Make : Legrand Arteor Cat Part No 573471, Schneider Cat Part No. IN8426/16, MK Cat Part No.K34383

S&F LED Pearl Round - LRS 2012 - 12W 240Vac, CCT - 4000K 960lm, CRI>80, Beam Angle - 110°,Dia.- Ø130mm,H - 30mm, Cutout- Ø105mm, Body material - Die Cast Aluminium, White Finish, IP20, complete all as specified & directed.

S&F LED Pearl Round - LRS 2015 - 15W 240Vac, CCT - 4000K 1275lm, CRI>80, Beam Angle -110°,Dia.- Ø160mm,H - 30mm, Cutout- Ø138mm, Body material - Die Cast Aluminium, White Finish, IP20, complete all as specified & directed.

S&F LED Opal - LRS 6008 - 8W 240Vac, CCT - 4000K 680lm, CRI>80, Beam Angle - 50°,Dia.- Ø88mm,H - 67mm, Cutout- Ø75mm, Body material - Die Cast Aluminium, White Finish, IP20, complete all as specified & directed.

S&F LED Ace track light - LAC 1015 - 15W 240Vac, CCT - 4000K 1275lm, CRI>80, Beam Angle - 30°,Dia-50mm X L-150mm, H - 145mm , Body material - Die Cast Aluminium, White & Black Finish, IP20, complete all as specified & directed.

S&F LED Tubo-D - LRS-S 3408 - 08W 240Vac, CCT - 4000K 520lm, CRI>80, Beam Angle - 100°,Dia.- Ø63mm, H - 185mm, Body material - Extruded Aluminium, White/Black Finish, IP20, complete all as specified & directed.

S&F LED Pill - ALP-S 6156 - 56W 240Vac, CCT - 4000K 3920lm, CRI>80, Beam Angle - 110°,Dia.- Ø600mm,H - 60mm, Body material - Extruded Aluminium, White/Black Finish, IP20, complete all as specified & directed.

S&F LED Ripple - ARL 6030 - 30W 240Vac, CCT - 4000K 2100lm, CRI>80, Beam Angle - 110°,Dia.- Ø600mm,Profile W-100mm,litup W-70mm, H - 60mm, Body material - Extruded Aluminium, White/Black Finish, IP20, complete all as specified & directed.

S&F LED Strapline-R 50mm -LSL-R 5030 - 30W/4ft 240Vac, CCT - 4000K 2400lm, CRI>80, Beam Angle - 110°, L- 3000mm, W-63mm, H - 80mm , Body material - Extruded Aluminium , White/Black/Grey Finish, IP20, Suspension wire, complete all as specified & directed.

S&F LED Strapline-R 50mm -LSL-R 5030 - 30W/4ft 240Vac, CCT - 4000K 2400lm, CRI>80, Beam Angle - 110°, L- 2400mm, W-63mm, H - 80mm , Body material - Extruded Aluminium , White/Black/Grey Finish, IP20, Suspension wire, complete all as specified & directed.

S&F LED Strapline-R 50mm -LSL-R 5030 - 30W/4ft 240Vac, CCT - 4000K 2400lm, CRI>80, Beam Angle - 110°, L- 1500mm, W-63mm, H - 80mm , Body material - Extruded Aluminium , White/Black/Grey Finish, IP20, Suspension wire, complete all as specified & directed.

S&F LED Strapline-S 50mm -LSL-S 5020 - 20W/4ft 240Vac, CCT - 4000K 1600lm, CRI>80, Beam Angle - 110°, L- 1800mm, W-53mm, H - 80mm , Body material - Extruded Aluminium , White/Black/Grey Finish, IP20, Suspension wire, complete all as specified & directed.

S&F LED Strapline-S 50mm -LSL-S 5020 - 20W/4ft 240Vac, CCT - 4000K 1600lm, CRI>80, Beam Angle - 110°, Hexo (L- 4000mm), W-53mm, H - 80mm , Body material - Extruded Aluminium , White/Black/Grey Finish, IP20, Suspension wire, complete all as specified & directed.

Taking down carefully existing sub main wiring with aluminium conductor/copper conductor cable of any size with GI earth wire including wooden batten etc and making good disturbed surface of walls etc, complete all as specified & directed.

S&F Sub main wiring with two runs of 10 Sqmm single core PVC insulated unsheathed FRLS multistranded copper conductor cable, 1100 volts grade drawn into and including PVC concealed conduit 'ISI marked' medium grade of suitable size as required, fixed in concealed surface of wall/ceiling including cutting chases as required with all fittings and fixing accessories & one run of 10 Sqmm PVC insulated unsheathed FRLS multistranded copper conductor cable for earth continuity wire, complete all as specified & directed. Make : Havells, RR KABEL, KEI Note:- Two runs of copper conductor 10 sqmm and one run of 10 Sqmm copper earth wire and one run of PVC conduit will be measured and paid as one unit only.

S&F Sub main wiring with two runs of 6 Sqmm single core PVC insulated unsheathed FRLS multistranded copper conductor cable, 1100 volts grade drawn into and including PVC concealed conduit 'ISI marked' medium grade of suitable size as required, fixed in concealed surface of wall/ceiling including cutting chases as required with all fittings and fixing accessories & one run of 6 Sqmm PVC insulated unsheathed FRLS multistranded copper conductor cable for earth continuity wire, complete all as specified & directed. Make : Havells, RR KABEL, KEI Note:- Two runs of copper conductor 6 sqmm and one run of 6 Sqmm copper earth wire and one run of PVC conduit will be measured and paid as one unit only.

S&F Sub main wiring with two runs of 2.5 Sqmm single core PVC insulated unsheathed FRLS multistranded copper conductor cable, 1100 volts grade drawn into and including PVC concealed conduit 'ISI marked' medium grade of suitable size as required, fixed in concealed surface of wall/ceiling including cutting chases as required with all fittings and fixing accessories & one run of 2.5 Sqmm PVC insulated unsheathed FRLS multistranded copper conductor cable for earth continuity wire, complete all as specified & directed. Make : Havells, RR KABEL, KEI Note:- Two runs of copper conductor 2.5 sqmm and one run of 2.5 Sqmm copper earth wire and one run of PVC conduit will be measured and paid as one unit only.

S&F factory made MCB DBs single pole with neutral sheet metal enclosures, double door type, 240 Volts, with 200 amp rated bus bar of suitable size plate and common neutral link all enclosed in standard steel sheet flush mounting type factory fabricated complete with out MCB and with enclosures blank plate for unused way suitable for 8 way including cutting chases and making good to walls, complete all as specified and directed. Make : Legrand CAt part No.507611, L&T CAT Part No.PH108DD8, Schneider CAT Part No.NBKRESNDD08

S&F factory made load line DB's double door made out of CRCA mild steel sheet with insulating materials like polyester epoxy coated surface mounting 8 way VTPN 415 Volts, IP 43 with suitable busbar, neutral link & earth link suitable for MCCB TP as incomer & MCB SP/TP as out going complete and including cutting chases and making good to walls, complete all as specified and directed. Make : Legrand CAT Part No.Pt 507759, L&T CAT Part No. PHV308DYM, Schneider CAT part No. NBKRENEZVDD08

S&F MCB SP 240 Volt of capacity 6 to 32 Amps, 10 KA rupturing capacity, IS-8828 marked, complete all as specified and directed. Make :Legrand CAT Part No. 408617, L&T CAT Part No. , Schneider CAT Part No. A9N2P32C

S&F MCB SP 240 Volt of capacity 32 to 60 Amp rating, 10 KA rupturing capacity, IS-8828 marked, complete all as specified and directed. Make :Legrand CAT Part No.408620, L&T CAT Part No.BA20630C, Schneider CAT Part No.A9N2P63C.

S&F MCB SPN 240 Volt of capacity 32 to 60 Amp rating 10 KA rupturing capacity, IS-8828 marked, complete all as specified and directed. Make :Legrand CAT Part No.408620, L&T CAT Part No.BA20630C, Schneider CAT Part No.A9N2P63C.

S&F MCCB TPN 63 Amp, 36 kA micro processor energy released type with OLED display complete all as specified and directed. Make.Legrand CAT Part No.420017, Schneider CAT Part No.A9TP160R, L&T CAT Part No.CM9819600MO.

Supply, installation, testing and commissioning of wall fan made of sturdy engineering plastic complete with all accessories, voltage 230V, 50 Hz, RPM 1200, copper winding of sweep 400mm 3 blade, single phase, complete all as specified and directed. Make: Bajaj CAT Part No.Esteen 400 mm double string, Khaitan CAT Part No.Merlin Hi speed 400 mm, Havells CAT Part No.Platina 400 mm.

S&F GI Raceway made from 1.5 mm thick pregalvanized sheet for top, bottom & sides and complete with top cover with rubber gasket of size 300x38mm complete for mounting and supporting the cable tray system, along with vertical bends, bends, including taking down and re fixing any type of electric cable, LAN /signal cable, if require through wall/floor cutting and making good surface of disturbed area, complete all as specified & directed. Make : Legrand, MK, Schneider

S&F GI Raceway made from 1.5 mm thick pregalvanized sheet for top, bottom & sides and complete with top cover with rubber gasket of size 100x38mm complete for mounting and supporting the cable tray system, along with vertical bends, bends, including taking down and re fixing any type of electric /signal cable, if require through wall/floor cutting and making good surface of disturbed area,complete all as specified & directed. Make : Legrand, MK, Schneider

S&F GI bracket for Raceway mentioned in above items here-in-before of 100 mm width, complete all as specified and as directed. Make : Legrand, MK, Schneider

S&F GI Bracket for Raceway mentioned in above item here-in-before of 300 mm width, complete all as specified and as directed. Make : Legrand, MK, Schneider

S&F Coupler for Raceway of 100 mm width, complete all as specified and as directed. Make : Legrand, MK, Schneider

S&F Coupler for Raceway of 300 mm width complete all as specified and as directed. Make : Legrand, MK, Schneider

S&F Pop up type flush mounting boxes for furniture equipped with :Push and Slide" locking system to avoid accidental opening by feet to be equipped with Arteor socket outlets for installation use whe flush mounting boxes for concrete floors of 8 modules (2 x 4), complete all as specified and directed. Make : Legrand, MK, Schneider

S&F Information outlets - toollers (Data so act) RJ-45 Category 6 Module, complete all as specified and directed. Make : Legrand, MK, Schneider

S&F Single outlet faceplate with RJ-45 jack, complete all as specified and directed.

S&F HDMI Socket, complete all as specified and directed. Make : Legrand, MK, Schneider

Supply, installation, testing and commissioning of 4 pair category 6 LAN cable consisting of 24 AWG solid copper conductors and as per the specification, complete all as specified and directed. Note : The cable should have flexible jacket and ripcord for easy stripability.

Supply, installation, testing and commissioning of 2 pair Category LAN cable consisting of 24 AWG solid copper conductors and as per the specification, complete all as specified and directed. Make : Havells, RR KABEL, KEI Note : The cable should have flexible jacket and ripcord for easy stripability.

S&F USB charging socket one module suitable to fix into moduler sheet used for switch socket, complete all as specified and directed. Note. Make of USB charging socket must be the sameas of the make of switch socket.

STAND BY POWER SUPPLY (UPS) Supply, installation, testing and commissioning of UPS for 30 min back up three phase AC input 300 to 450V and out put single phase AC out put Voltage 230 V ± 1% of capacity 40 KVA including provn of three phase electric supply of input and single phase output supply UPS to distribution board, backup battery bank with standing rack (made of MS dully painted ), complete all as specified and directed. Note : Pure sinusoidal output (no flickering in LED based devices ) must be ensured at the time of installation cum testing.The UPS and battey system must satisfy following conditions - 1. Have an active power factor correction system, input power factor up to 0.99 2. Output power factor- 1.00 3. 50/60 Hz auto sensing frequency 4. 50/60 Hz frequency conversion mode 5. Fan speed varying intelligently with load, reducing noise and extending service life 6. Digitally controlled charger 7. Ability to switch on UPS by battery in the absence of mains power (cold start) 8. Volatge regulation +or- 1% 9. Having sinusoidal output waveform 10. THD <= 1% for linear load and <= 4% for non linear load 11. Batteries: 40 kVA built in battery (30-44 pcs settable) 12. System Transfer time - 0 ms 13. Having following system for protection - short circuit, overload, over temperature, excessive low battery, over volatge, under voltage fans failure 14. Max no of parallel connections -4 15. Operating temperature - 0-45 degree C 16. Storage temperature: -25 degree C to 55 degree C (without battey) 17. Min IP rating - IP 20 18. Noise level at 1 meter - <= 65 dB Make. APC (Schenider), Luminous, Microtek

FIRE FIGHTING Providing and fixing MS (Heavy Class) pipes confirming to IS : 1239 pipes painted with one coat of primer & two coats of post office red enamel paint suspended in ceiling, walls, columns for all heights with hangers / supports and fasteners all as per drawing including chasing of walls / coloumns / ceiling etc. and making good the same complete required, complete all as specified and directed for the following size of pipe :-

(a) 25mm dia

(b) 40mm dia

(c) 80mm dia

(d) 100mm dia

Supplying, fixing, testing and commissioning of butterfly valve, 100 mm dia of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS:13095, complete all as specified and directed.

Supplying, fixing, testing & commissioning of 15mm dia quartzoid bulb type Pendent Sprinkler of rating 68 degree centigrade with required accessories, complete all as specified and directed.

Supplying, installation, testing & commissioning of sprinkler flexible pipe 600mm (UL Listed) of stainless steel complete with 15 NPT on reducer thread with maximum working pressure of 175 PSI test pressure of 875PSI (Burst) with branch line (Inlet) 25mm NPT male thread to sprinkler head (Outlet) 15mm NPT female thread with reducer, nipple, 2 side brackets, center bracket, stock bar , complete all as specified and directed.

Supplying, installation, testing & commissioning of adjustable rosette plate for 15mm dia in white finish UL Listed or FM approved, complete all as specified and directed.

S&F ABC powder stored pressure type fire extinguishers capacity 6 kg, confirming to IS:13849 consisting of welded MS cylindrical body, squeeze lever discharge valve fitted with pressure indicating gauge internal discharge tube, 30 cms long high pressure discharge hose, discharge nozzle, suspension bracket, conforming to ISI finished externally with red enamel paint and fixed to wall with brackets complete with internal charge, complete all as specified and directed.

S&F Carbon-di-oxide fire extinguishers capacity 4.5 kg, ISI marked consisting of welded M.S cylinderical body,squeeze lever discharge valve fitted with internal dischargetube, 30cms long high pressure discharge hose, discharge nozzle, suspension bracket, confirming to IS : 934 finished externally with red enamel paint and fixed to wall with brackets with rawl plug/dash fasteners complete with internal charge.

Supplying, installation, testing & commissioning of microprocessor based intelligent and analougue addressable, modular, expandable, loops as given below (each loop consist of 159 detector & 159 devices ) fire alarm control panel panel with minimum 6 inch /640 character LCD display, multiple access levels, event history fire in non-volatile memory (EEPROM). The panel shall support programmable relays for controlling lifts, staircase pressurizations fans, lift shaft and lift lobby pressurization fans, AHU's ventilation fans, fire pump, monitoring of fire sprinkler and fire hydrant pump controlled by powerful Boolean logic equation. The panel shall have inbuilt qwerty keypad for field programming and shall have the capability to record 4000 event logs, it shall have 240 volts AC power supply automatic battery charger, 24 volts, sealed lead acid-maintenance free batteries sufficient for 24 hours normal working and then be capable of operating the system for 60 minutes during emergency condition. Qwrety keypaid The panel shall be UL Listed 9th Edition, complete all as specified and directed. Note : control panel to be interconnected to main control panel of scope complex .

Supplying, installation, testing & commissioning of UL listed addressable intelligent Photothermal (Multitech) detector with floating sensitivity (Acclimate type) with mounting base, dual LED,complete with base as required, complete all as specified and directed.

Supplying, assembling erection, testing & commissioning of Response indicator which consists of steady glowing LED. This LED shall be mounted within a M.S. box and connected in parallel to the built in indicator of the detector as per specifications. The RI shall come "ON" as soon as the detector activates, complete all as specified and directed.

Supplying, installation, testing & commissioning of addressable Control Module for tripping of AHU, Fire Damper etc. including all relays, contacts etc, complete all as specified and directed.

Supplying, installation, testing & commissioning of addressable Monitor Module for sprinkler flow switch, Aspirations System etc, complete all as specified and directed.

Supplying, installation, testing & commissioning of Intelligent addressable Manual Call Point with inbuilt isolator or isolator before and after, break glass type with alarm LED as detailed, complete all as specified and directed.

Supplying, installation, testing & commissioning of Directional Sounders with 20 hz to 20 khz operating frequency with minimum 8 distinct sound patterns to indicate corridors, Exit doors, Move upward, move down ward etc. to direct Occupants for fast & safe Evacuation as specified in NFPA 72 - 2007 edition. (UL 9th Edition Approved and NFPA compliant), complete all as specified and directed.

Supplying & laying of 2x1.5 sqmm fire survival armoured cable, 600/1000V rated with annealed copper conductor having glass mica fire barrier tape covered by an extruded layer of Cross Linkable Ethylene Propylene Rubber (EPR) insulation and LSZH inner bedding, steel wire armouring & LSZH outer sheath, complete all as specified and directed.

AIR CONDITIONING Supplying, installation, testing & commissioning of 100% Inverter 10 HP VRF Outdoor units complete with Inverter Scroll compressor fitted with conentrated winding, air cooled condenser with low noise fan having interconnected control wiring and refrigerant piping housed in compact housing duly powder coated, Conformal Coating on PCB, Hydrophilic Blue Fins, High efficient Compressors in Outdoor Unit of following capacities. ( Cooling & Heating ) - Eco Friendly Refrigerant (R-410a). Operating Outdoor Ambient Temperature Range (Cooling 10°C to 56°C & Heating -10°C to 24°C) Make: Daikin, Mitsubishi, Bluestar

Supplying, installation, testing & commissioning of Cassette Units of capacity 2.0 Tr (695CFM) with evaporator coil, fan and Fan motor, cordless remote control, Drain Pump and necessary accessories etc suitable for operation on 230 V +- 10% 50 Hz single phase AC supply, complete all as specified and directed

S&F Refrigerant Y-Joint for combining Outdoor and Indoor Units required for distribution of refrigerant in copper piping as per final approved drawing which will be submitted by OEM, complete all as specified and directed.

Supplying, installation, testing & commissioning of high pressure interconnecting refrigerant pipe of following sizes including civil work like wall opening for copper and drain pipe for VRF system with (19mm/13mm thick) closed cell elastomeric nitrile rubber tubular insulation between indoor & outdoor units as per specifications. All Piping install on cable trays with cover for outdoor locations as per OEM recommendations and PVC sleeves shall be provided wherever pipe is crossing the wall. Food grade nitrogen shall be used while making brazing joints, complete all as specified and directed for the following sizes :- Make: Mandev, Maxflow, Rajco

(a) 9.5 mm with 13 mm thick insulation

(b) 12.7 mm with 13 mm thick insulation

(c) 15.9 mm with 13 mm thick insulation

(d) 19.1 mm with 13 mm thick insulation

(e) 22.2 mm with 19 mm thick insulation

(f) 28.6 mm with 19mm thick insulation

Supply and fixing in position the 32mm dia of PVC (UPVC quality) pipes, cut in required lengths and joined with PVC cement and also providing and fixing in position the necessary "U" trap elbows, tees, and reducer and all types of fittings. Cost to include all necessary as required. Necessary Wall cutting and making the wall good and its cost should be included. The pipe to be insulated by 9mm thick nitrile rubber thermal insulation of class 0 category, complete all as specified and directed.

Supply, fixing, testing and commissioning of 2 Core x 0.75mm² control wiring ( Sheilded Wire) from outdoor , indoor units to the central controller with all necessary accessories to make it functional as per OEM Recommendation, complete all as specified and directed.

S&F of MS Stand as per OEM Recommendation and Placing of Outdour Unit on MS Stand of C Channel, complete all as specified and directed.

Supply & charging of Refrigerant Gas R410a as per OEM Recommendation, complete all as specified and directed. Make: SRF Floron, Honeywell & Dupont

S&F 125mm deep Antivibration Flexible Joints made out of imported fire retardant fabric with extruded aluminium frame/ flange on both sides for Outdoor Units, complete all as specified and directed.

Supply , assembly and erection in replacement GI sheet rectangular/square duct made out of 'L' shaped hollow profile, duly factory boxed, including all accessories such as corner, Cleat , Carrige bolt, Gasket and appropriate sealant on langitudinal joints etc complete including necessary MS Channels, Gurder supports as approved by Engr-in-charge including making of hole in any type of wall and making good with plastering work , masonry work and necessary MS channel supports complete all as specified and as directed for the followings :-

(a) 24 Gauge GI Sheet

(b) 22 Gauge GI Sheet

Supply & erection of 19 mm thick nitrile duct insulation with Aluminum foil. The thermal insulation shall be 25 mm thick non-fibrous, fire retardant, closed cell, tri- dimensional chemically crosslinked polythylene foam, confirming to class O' for fire propagation and class 1 for surface spread of flame & factory laminated aluminum foil, complete all as specified and directed.

S&F Insulation acoustic lining of supply air ducting complete with GI frame , tissue paper , 26 Guage perforated AL Sheet 25mm thick of density 32 kg/cum fiber glass insulation, complete all as specified and directed.

Supplying, installation, testing & commissioning of UL-555 motorized fire dampers complete with smoke detector/ thermister linkage etc in Supply Air Ducts as required for operation, complete all as specified and directed.

Supplying, installation, testing & commissioning of Actuator with control panel Supply Air Ducts as required for operation, complete all as specified and directed.

Supplying, installation, testing & commissioning of air Grills and without volume control dampers , power coated , extruded aluminium, construction, complete all specified and as directed.

Supplying, installation, testing & commissioning of air Grills and volume control dampers , power coated, extruded aluminium construction complete all specified and as directed.

S&F MCB, triple pole & neutral, 40 Amps, AC, 415v, 50Hz, breaking capacity 10 KA, complete all as specified & directed.

S&F Sub main wiring with two runs of 4 Sqmm single core PVC insulated unsheathed FRLS multistranded copper conductor cable, 1100 volts grade drawn into and including PVC concealed conduit 'ISI marked' medium grade of suitable size as required, fixed in concealed surface of wall/ceiling including cutting chases as required with all fittings and fixing accessories & one run of 4 Sqmm PVC insulated unsheathed FRLS multistranded copper conductor cable for earth continuity wire, complete all as specified & directed. Note:- Two runs of copper conductor 4 sqmm and one run of 4 Sqmm copper earth wire and one run of PVC conduit will be measured and paid as one unit only.

S&F Sub main wiring with two runs of 1.5 Sqmm single core PVC insulated unsheathed FRLS multistranded copper conductor cable, 1100 volts grade drawn into and including PVC concealed conduit 'ISI marked' medium grade of suitable size as required, fixed in concealed surface of wall/ceiling including cutting chases as required with all fittings and fixing accessories & one run of 1.5 Sqmm PVC insulated unsheathed FRLS multistranded copper conductor cable for earth continuity wire, complete all as specified & directed. Note:- Two runs of copper conductor 1.5 sqmm and one run of 1.5 Sqmm copper earth wire and one run of PVC conduit will be measured and paid as one unit only.

Taking down carefully existing old air conditioner duct any size from interior including fittings and fixtures such as supply air grill with duct and return air air grill with duct with insulation materials and removal of any electric conduit or any fitting fixture if any left at site etc from existing concealed /open from ceiling /wall and making good the disturbed surface of wall/ floor complete to match with the existing surface/finishes, complete all as specified and directed. Note :Removing materials to store for keeping in safe custody of user.

M/s Arihant Builders (BID ID -3151634)

ASSOCIATED CONSTRUCTION CO. (BID ID -3145932)

M/s. Shiva Engineers (BID ID -3152267)

JYOTI ENTERPRISES (BID ID -3151628)

ASSOCIATED CONSTRUCTION CO. (BID ID -3145932)

M/s Arihant Builders (BID ID -3151634)

M/s. Shiva Engineers (BID ID -3152267)

JYOTI ENTERPRISES (BID ID -3151628)