PROVN OF TOILET AND WAITING SHED AT RP GATE, SEPTIC TANK AND SOAKAGE WELL ALONGWITH SEWAGE LINE, HARD STAND FOR DG SET OF ASCON NODES, BATHROOM AND TOILET SET WITH SOAKAGE PIT AT C-41 SECURITY POST AND SPL REPAIR TO BOUNDARY WALL (150MTR) OF SECTOR

Amount

Surface excavation (not exceeding 30cm deep) and averaging 15 cm , getting out in soft / loose soil.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out

Excavating in trenches, n exc 1.5 m wide and n exc 3.0 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 3.0 m in depth and getting out

M&L cement concrete (1:4:8) type D2 using 40mm graded stone aggregate as in foudation, filling, sub base and mass concrete all as specified.

M&L for PCC 1:3:6,type C-2 using 40mm graded crushed stone aggregate as in sub base, mass conc and like complete all as spfd and directed (Note :Necessary formwork shall have to be done by contractor at its own cost of same deemed to be included in items )

M&L brick work in cement mortar (1:4) using fly ash bricks in walling, straight or curved on plan exc 6m mean radius all as specified.

Returning filling in including spreading levlling ,atering and well ramming in layers nexc 25cm thick complete all as spfd.

Removing excavated soil to a distance n exc 50m and depositing at alevel n exc 1.5m above the starting point

M&L brick work in cement mortar (1:4) using fly ashbricks in walling,straight or curved on plan to any radius in half brick thick wall all as specified.

M&L 40 mm thick for damp course to horizontal surfaces in cement concrete 1:2:4 type B-0 using 12.5 mm graded crushed stone aggregate incl all necessary form work

M & L for RCC design Mix M-25 (1:2:4 Type-B1) Using 20 mm greaded Stone Aggregate in Beams, cantilevers, bressummers, lintels over complete all as specified and as directed.

M&L RCC M-25 Design Mix as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete using 20mm graded stone aggregate complete all as specified and directed

M&L RCC M-25 Design Mix as in columns, pillars, piers posts and struts using 20mm graded stone aggregate complete all as specified and directed.

M&L for Formwork to sides and soffits of floor or roof beams, beam haunch haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc.

M&L Formwork to sides and soffits of beams , beam haunchings , girders, bressumers, lintels, cantilevers, shelves including supports, overhangs, etc also splays between floors and beams , etc rough finished flat surfaces, complete all as specified and directed.

M&L Formwork to sides of pillars, posts, struts, piers, columns and stanchions rough finished flat surfaces, complete all as specified and directed.

M&L for TMT steel bars 6 to10mm dia and over cut to length bent to shape reqd incl cranking bending spirally for hooping for columns hooking ends and binding with m.s wire annealed not less than 0.9mm dia

Ditto all as per above 17 but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders complete all as specified and directed by Engr-in-charge

M&L for 10mm thick rendering on fair faces of brick /concrete surfaces in cement mortar 1:4 and finished rough for receiving tiles as in dado complete all as specified.

M&L for rendering 5 mm thick on celling fair faces of concrete surfaces in cement mortar in cm 1:3 finished fair and even without using extra cement complete all as specified and directed by Engr-in-charge

M&L glazed ceramic coloured tiles in vertical surfacaes 350x250x7mm/450x300x7mm thick set set and jointed in neat cement slurry and pointed in white or coloured cement mixed with pigment complete all as specified and directed by Engr-in-charge

M&L for 25mm thick PCC type B-0 using 20mm graded crushed stone aggregate as in sub base for laying floor finishes complete all as specified

M & L for Screed bed or bedding layer of mortar(1:6) 20 mm thick for laying floor finishes complete all as specified and directed by Engr-in-charge

M&L for Virified Ceramic tiles light shade10 mmthick (square/ rectangular) polished, area of each tiles not exceeding 1.00 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match ® Size (600x1200) complete all as specified and directed by Engr-in-charge

S&F solid PVC door frames of size 50mmx47mm madwe out of 5mm prelam sheet in stead of plane colourPVC sheet & eadgs will be painted to match with prelam sheet sheet reinforced with ms square tube complete all as spd

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S tubes for top & bottom rails. M.S frame shall bw covered with heat moulded plain colour PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and botom rail on either side & as gap insert for tip rail & bottom rails; Panelling of plain colour PVC sheet to be fitted in the MS frame weloded/sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement. suppling and fixing in the frame at site .

S&F factory made mild steel Window/Ventilator box type with side huge shutters incl pintol hinges,steel handles, steel peg stay and all locking arrangement and one shop coat of red oxide primer complete all specified. Note : i) The window shall be fabricated as per Drg No CEBTZ/TD/888R & 889 ii) MS fillets, glazing, wire gauge shall be measured and paid separately iii) opening incl provn shutter for cooler to be provided

S&F 3 mm thick sheet glass ordinary quality and glazing with oil putty in squares n exe 0.5 sqm each pane complete all as specified and directed by Engr-in-charge

S&F galvanised mild steel wire cloth 0.56mm nominal dia of wire and avg width of aperture1.18mm complete all as specified and directed by Engr-in-charge

S&F 150mm size aluminium anodised barrel tower bolt of extruded section and fixed complete all as specified and directed by Engr-in-charge

S&F 150mm size extruded aluminium handles fabricated type, anodised and fixed complete all as specified and directed by Engr-in-charge

S&F 100 mm long Butt hinges extruded aluminium alloy , with galvanised mild steel hinge pin, anodised, type B-21, ISI marked complete all as specified and as directed by Engineer-in-Charge.

M&L for rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:4 and finished smooth and even without using extra cement.

M&L for rendering 10 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:4 and 5 mm thick in CM 1:4 as second layer incl. mixing water proofing compound and finished fair and even without using extra cement.

M&L for hardcore of gauge nexc 63mm , deposited , spread and levelled in layers nex 15cm thick watered and rammed to a true surface

M&L for Moorum/red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering complete all as specified and directed.

M&L for 75 mm thick cement concrete 1:3:6 type C-2 (using 40 mm graded stone aggregate) as in plinth protection laid to slope of 1 in 12 and finishing cement concrete surface even and smooth without using extra cement with and including all necessary form work to divide the area in panels, finishing exposed edges fair or rounding or chamfering of exposed edges where directed and providing 6 mm thick joints through the thickness of plinth protection duly filled with mastic filling of one part of hot bitumen 85/25 grade and three parts of fine sand (all by weight) complete.

S&F 110 mm bore PVC (SWR) 'S" trap/gully trap 125/110 complete all as specified and directed. .

S&F PVC (SWR) PVC (SWR) bends 110 mm bore any radius

S&F PVC (SWR) vent cowl for 75mm dia pipe all as specified.

S&F PVC (SWR) 110mm bore pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed.

S&F PVC (SWR) 75 mm bore pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed.

S&F PVC (SWR) bends/single T any radius 75 mm fitted with oval access door. all as specified.

S&F PVC (SWR) bends /single T any radius 110 mm fitted with oval access door. all as specified.

S&F 75mm PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and directed.

Stack clamp out of 50mm x5mm flat iron stays including bolt and nuts and securing ends of stays to walls or roof for 75mm bore piece complete all as specified and directed by Engr-in-charge

Stack clamp out of 50mm x5mm flat iron stays including bolt and nuts and securing ends of stays to walls or roof for 110mm bore piece complete all as specified and directed by Engr-in-charge

S&F 500 ltr Rotational moulded polyethylene water storage tanks (Cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I, 450 ltr Capacity, including Ball brass valves, high pressure, with polythene float and flynut com complete all as specified and directed by Engr-in-charge

S&F 15 mm bore brass valve high pressure with polythene float valve and fly nuts complete screwed for iron pipe complete all as specified and directed by Engr-in-charge

S&F Vitereous china wash down water closet pan (Pedestal pattern) white including trap bolts etc complete including connections to drain and seat cover and anti siphonage pipe complete all as specified and directed by Engr-in-charge

S&F in PVC flushing cistern,low level, white with inlet, ball valve ,complete including connection to pipe complete all as specified and directed by Engr-in-charge

S&Fin repair 15mm bore PVC connection with PTMT nuts length 450 mm complete all as specified and directed by Engr-in-charge

S & F in repair Viterous China urinal half stall type complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; white including CP spreader, waste pipe etc.

S&F vitreous china wash hand basin white flat back, size 550x400 including and wood etc complete all as specified.

S&F Waste pipe 32mm for WHB with coupling fixed in repairs.

S&F Chromium plated soap dish complete all as specified and directed by Engineer-in-charge.

S&F Steel water tubing 20mm bore medium grade galvanised with all fittings including short lengths, fixed to walls, concealed in wall and ceiling or laid in floor complete with all fittings (such as bends, elbows , tees, short pieces, connectors, back nuts, diminis

S&F Steel water tubing 15mm bore medium grade galvanised with all fittings including short lengths, fixed to walls, concealed in wall and ceiling or laid in floor complete with all fittings (such as bends, elbows , tees, short pieces, connectors, back nuts, diminis

S&F Bib Tap, cast copper alloy with crutch or butterfly handle chromium plated screwed down screwed for iron pipe or brass ferrule, fancy type, CP, 15mm dia complete all as specified and directed by Engr-in-charge

M&L for 15 mm bore angle valve / Stop valve cast copper alloy screwed down, high pressure with crutch or butterfly handle , screwed both ends for iron pipe or for unions of 15mm dia all as specified

S&F 20 mm bore Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe complete all as specified and directed by Engr-in-charge

M&L for prep of new plastered surfaces of walls by applying a thin layer of Birla white putty to give uniform surface applying two coat of oil bound distamper on new surfaces of desired finish as app by Eng-in-charge in any position complete all as specified and directed by Engr-in-charge

M&L for Preparing plastered or unplastered surfaces of ceiling/wall including complete removal of existing treatment by mechanical equipment like electric sander and applying two coats of oil bound distemper over 3mm thick wall care putty, white or tinted complete all as specified and directed by Enginner in charge.

M&L for preparing new plastered surfaces and applying two coats of cement base paint on surfaces of walls complete all as specified and directed by Engr-in-charge

M&L for preparation of new steel and iron surfaces exceeding 10 cms width or girth and applying two coats of synthetic enamel paint over and incl a coat of red oxide primer all as specified.

S&F Anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and directed by Engr-in-charge

S&F Sheet glass, ordinary quality 5.5mm thick for Aluminium door ,window and vent and glazing in square n exc 0.5 sq. m in each pane complete all as specified.

S&F Neoprene/ EPDM rubber gasket for fixing sheet glass complete all as specified and directed by Engr-in-charge

S&F of 4 levers Mortice lock, vertical type, size 100 mm complete all as specified and directed by Engr-in-charge

S&F Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed

S&F in replacement curtain rod 25mm dia, mild steel, chromium plated, fancy type with fixing brackets and knobs at both ends as per site requirement complete all as specified and directed by Engr-in-Charge Note :- The cost of brackets and knobs is deemed to be incl in the quoted rate. Nothinbg extra shall be paid on this account.

S&F Grating doom 125 mm dia with waste hole of PTMT. (Minimum weight 40gms complete all as specified and directed by Engr-in-charge

S&F in repairs 15mm bore Brass CP mixer for mixing hot & cold water screwed down for iron pipe and fixed complete all as specified

S&F Composite cement ceiling board 4 mm thick in ( 595 mmX595 mm ) pannel (Make-everest ramco or eql.) designer ceiling pre finished conforming to IS 14862 type B cateogory three incl aluminium frame , snap grid work,hold fast,suspended with suspender along with holding down bolt complete . (Note: Ceiling board shall confirming to IS-14862 ,shall be fire resistant , Moisture resistant and ceiling shall be suspended with suspenter and adjuster)

M&L Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.5mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall,fixed with self tapping screws as specified. (Note - Color Sand/or as approved By Garrision Engineer)

M&L steel work in tubular trussess/ purlins incl spl shaped washer etc. using ERW or induction butt welded tubes confirming to IS 1161-1979 grade St-240. complete all as specified and directed by Engineer-In-Charge.

S&F Mild steel bolts.exc. 5 cm length not exc. 10 cm length (machine made) with hexagonal or square heads at one end and screwed the other , or screwed both ends, each screwed end to be fittied with washers and one hexagonal or square nut 11 to 15 mm neck dia complete all as specified and as directed by engineer-in-charge.

S&F plates (Plain or chequred) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachement complete all as specified and directed by Engr-in-charge

M&L for conc 1:3:6 type C2 using 40mm graded aggregateas in bed to 150mm drain pies incl packing under and haunching against the sides of pipes after they are laid and tested for complete all as specified and directed by Engr-in-charge

S&F salt glazed stone ware drain pipe 150mm bore, class 'SP 2' ISI marked ,laid to slope in trenches and jointed in CM (1:1) and Tested complete all as spfd and directed. Note:-Excavation and earthwork shall be measured and paid separetely.

M&L brick work in cement mortar (1:4) using old size sub class 'B' bricks in walling, straight or curved on plan exc 6m mean radius complete all as specified and directed by Engr-in-charge

M&L For PCC type B1(1:2:4) using 20 mm graded cushed stone agg as in coping ,benching and the like incl form work complete all as specified and directed by Engr-in-charge

M&L Precasted RCC 1:2:4 type B1 using 20mm graded aggregates for precast cement conc slabs as in drain/ manhole covers set in cement mortar1:4.(Note : Slab covers shall be floated with surface vibrator,and over turfed base ,arrandement for turfed base has to be from contractors side)

Supply only integral water proofing compound complete all as specified and directed by Engr-in-charge

M&L for 75mm thick PCC 1:4:8 type D2 (using 40mm graded aggregate) complete all as specified and directed by Engr-in-charge

M&L for 100mm thick PCC 1:2:4 type B2 (using 20mm graded aggregate) complete all as specified and directed by Engr-in-charge

M&L for plastic dividing strips, 1.5mm thick and 38mm wide complete all as specified and directed by Engr-in-charge

M&L for preparation of new surfaces of wall/ceiling incl pillar etc and applying two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon addtives @ 1.43 litre/10 sqm over and including priming coat of exterior primer applied @0.90 litre/10 sqm over wall surfaces by mechanical means as per manufacturer's specification all as specified and as directed by GE.

M&L for PCC 1:2:4,type B-1 using 20mm graded crushed stone aggregate as in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height copings, kneelers, apex stones, bed plates, kerbs not provided for in Item 04028, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, as directed complete all as specified and as directed.

M&L for Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using ex- tra cement, including forms, moulds, mi- tred/stopped ends etc.

M&L for Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-l smooth finished, and reforming benching as required

M&L for 30 users on site LLDPE Septc tank designed to carry sewage and sullage water , excavation in any type of soil,PCC 1:4:8 below foundation, Roof slab including beams ,vent shaft ,connection etc,complete .

Soakage wells excavation, in any type of soil, foundation in PCC 1:3:6, walls of honey combed masonry with top ring of M25 concrete including intercepting chamber and screen chamber made of Brick masonary in CM, RCC cover slab in M25/ SFRC cover, interconnecting pipes of RCC/DWC complete filled with brick bats of size 3.0m dia and 3.00m effective depth as per Drg BTD 830

M&L for Demolition of Brickwork or stone/ boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed complete all as specified

S&F Hand rails, half round or other steel section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof complete all as specified and directed.

S&F 110mm bore PVC pipe(SWR) as in weep holes complete all as specified and directed by Engr-in-charge

S&F galvanised , 2 strand , steel barbed wire 2.24 mm dia with 2mm dia barbs at 75mm spacing and straining and fixing to any type of standard rails including securing or tying with and provision of galvanised MS wire staple or steel pins etc complete all as specified and directed.

S&F Concertina coil with punched tape of 600mm dia, centre core wire shall be minimum 2.5mm dia of mild steel conforming to IS 280-2006, galvanised coating of steel concertina coil shall confirm to requirements as laid down for medium coated wire in IS 4826 "Hot dip galvanised coating of round steel wires" concertina coil shall be fixed in diamond shape the help of dove tail two handles and spikes shall be fixed at both ends of coil, complete all as specified and directed.

M&L Jodhpur stone of roof slabs, self faced 7.5 cm to 10cm thick, 25cm to 35cm wide, hoisted and set, jointed and grouted in lime mortar 1:3 or cement mortar 1:6 complete all as specified and directed by Engr-in-charge

M&L for 50mm thick PCC 1:3:6 20 m graded stone aggregate type C-1 using 20mm graded crushed stone aggregate as in levelling course for receiving roof treatment complete all as specified

Applying evenly a tack coat of industrial bitumen 85/25 ,1.2kg/sqm incl cleaning surface complete all as specified and directed by Engr-in-charge

S&F APP based polymeric membrance min weighing 3kg/Sqm and minimum 3mm thick reinforced with polyster non wove fabric land on primed surface by force application complete all as specified and directed by Engr-in-charge

M&L for Lime concrete terracing as specified on roof complete all as specified and directed by Engr-in-charge

M&L for 40 mm thick Brick tiles bedded in 15 mm thick cement and sand mortar (1:6) and joints grouted flush in cement and sand mortar (1:3) mixed with 5% of crude oil by weight of cement complete all as specified and as directed by Engineer-in-Charge.

M & L for non skid ceramic colour (light shade) joint free tiles with matt finish size 400x400x7mm thick ( square/ rectangular ) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed over Screed bed or bedding layer of mortar 20 mm thick for laying floor finishes confirming to IS-15477:2004 including necessary cutting as per site requirement complete all as specified and directed by Engineer - in - Charge.

M&L for 25mm thick PCC type B-0 using 20mm graded crushed stone aggregate as in sub base for laying floor finishes complete all as specified and directed by Engr-in-charge

Supplying and laying of CPVC pipes of 20 mm outer dia SDR 11 & Plain CPVC SDR 11 fittings in trenches, wall complete all as specified.

Supplying and laying of CPVC pipes of 25 mm outer dia SDR 11 & Plain CPVC SDR 11 fittings in trenches, walls complete all as specified.

S&F in brass chromium plated shower rose 125mm size with swivel joints arm complete all as specified and directed by Engr-in-charge

S&F in repair 15 mm bore brass fancy concealed type stop valve chromium plated with long shank and cup complete screwed for iron pipe complete all as specified and directed by Engr-in-charge

M & L for Modular point wiring for one light/fan/bell/buzzer point controlled by one way switch with 1.5 sqmm single core PVC insulated and sheathed multi stranded copper conductor FRLSH cable 1100 volts grade (ISI Marked) including 1.5 sqmm single core PVC insulated and sheathed multi stranded copper conductor FRLSH cable 1100 volts grade (ISI Marked) as continues earth wire in green colour to coomon earth dolly laid/drawn into and including non metalic PVC concealed conduit (medium duty, ISI marked not less than 20 mm dia) with all fittings such as tee, bends etc all as per IS terminated in & including new modular metal flush boxes of requisite module concealed in wall for mounting fittings like modular Switches, sockets, regulators etc with and including modular cover plates with frame of requisite modules all as specified and as directed: Notes:- (i) Cost of cutting/leaving forming chases for conduit, sinking for metal flush boxes and making good in CM 1:4 shall deemed to be included in quoted rate of this item. (ii) The quoted rates of this item shall deemed for include for modular metal flush boxes of requisite module and modular cover plate with frame of requisite module of colour as approved by GE

(b)One pin 5 amps socket point on the same board with other switches complete

(c) One 3 pin 5 amps socket on independent board.

Ditto all as per item No 112 here -in- before but for one 3 pin 15 Amps socket outlet controlled by one 15 Amps switch on independent board with 2.50 sqmm single core PVC insulated and and sheathed multistranded copper conductor FRLSH cable 1100 Volt grade (ISI marked) including 2.5 Sqmm single core PVC insulated and sheathed multistranded copper conductor FRLSH cable 1100 Volt grade (ISI marked) as continuous earth wire in green colour complete all as specified and directed .

S&F switch Modular type, 6 Amp, 1 module single pole one way, 230 Volts, Modular type complete all as specified and as directed by Engr- in -charge.

S&F switch Modular type, 16 Amp, 1 module single pole one way, 230 Volts, Modular type complete all as specified and as directed by Engr- in -charge.

M&L socket outlet 3 Pin 6 Amps modular type, 2/3 pin combined 2 module 230 Volts complete all as specified and directed by Engr-in-Charge.

M&L socket outlet 3 Pin 6/16 Amps modular type, 2/3 pin combined 2 module 230 Volts complete all as specified and directed by Engr-in-Charge.

S&F Single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB 20 Amp complete all as specified and as directed by engineer-in-charge.

S&F ceiling rose, surface backelite , three terminal AC, 230 volt complete all as specified.

S&F LED tube light fitting, 1x 20-22 watts, 230 volt, basic all purpose surface and wall mounted led batten with polycarbonate housing & integrated electronic driver, pre-wired and fixed on walls with all fixing accessories such as screws, clips etc and connecting up with two core flexible copper conductor cable of size 24/0.20 sqmm complete all as specified and directed by Engr-in-charge.

Supply and fixing LED mirror light fitting , type with high out put diffuser 2 feet, 10watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and as directed by Engr-in-charge

Supply and fixing LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete.

S&F GI bracket made out of 40 mm bore GI pipe light grade /medume grade, ISI marked, medium grade 1.2m long bent to shape suitable for fixing of street light fitting including with 2 Nos MS clamps made with 40x3mm flat iron, bolts, nuts, washers etc including two coats of synthetic enamel paint over one coat of zinc chrome primer and fixing on electric pole complete all as specified and as directed by Engr-in-charge.

S & F MCB TPN, 63 to 100 Amps, 415 volts, breaking capacity 10KA complete all as specified and as dircted by Engr-in-charge.

Supply and hanging/fixing ceiling fan of capicity 26 watt with remote control complete with blades down rods electronic regulator and accessories , 230 V 1200 mm sweep Min air delivery 210 CFM with services value 6 BEE Five star rated with brushless direct current motor ( BLDC ) complete all as specified and as directed by Engr-in-charge.

Supply and fixing exhaust fan (heavy duty) steel body, AC single Phase 230V, 50 Cycle per second, size 300 mm sweep with blades and frame including new GI wire mesh heavy duty with wooden frame protection against birds etc including provision of cutting of existing wall for suitable opening as per fan, including electric connection with and including new 1 Sqmm, 2 core flexible copper conductor cable from ceiling rose to fan, fan hanging on wall with 4 Nos steel fastners 10mm dia 100mm long and making good the disturbed surface complete all as specified and as directed by Engineer-in-charge. Note :- Serial Number of exhaust fan issued by Engr-In-Charge and GE Office name shall also be written on fan with red colour permanent marker.

S & F double door, sheet metal enclosure, powder coated for MCB DB SPN 8 way fitted with neutral link, earth bar , din rail and 200 amps rated bus bar 230 volt conforming to IS 13032-1991 complete all as specified and as directed by Engr-in-charge.

S & F MCB SP, 5-32 Amps , 240 volts, breaking capacity 10KA complete all as specified and as dircted by Engr-in-charge.

S & F MCB SPN, 5-32 Amps, 240 volts, breaking capacity 16KA complete all as specified and as directed by Engr-in-charge.

S & F water heater storage type 25 Ltr capacity, BEE 5 star and 8 bar pressure rated stainless steel (minimum wall thickness 2 mm) tank with feroglass coated inner container energy saving high density PUF insulation vertical ABS shock proof plastic body grouting of studs in wall in cement motar (1:3) nuts, washers, provision of two Nos PVC braided connection 450mm long heavy duty with brass nuts and two Nos brass chromium plated angular valve,thermostate,NRV ,TOP PLUG 20AMP with valve flange suitable for 15mm bore pipe for water supply connection complete.

M&L for Earthing complete with galvanized steel earth plate electrode 60cm x60cm x 6mm thick buried directly in ground (earth pit not less than 2.25 meters deep below normal ground level) with top edge of plate not less than 1.5 meters below normal ground level connecting to the galvanised earth lead wire 4.0 mm dia by means of bolts, nuts check nuts and washers of galvanized iron and steel earth wire protected by provision of GI mediumgrade pipe 15mm bore including provision of concrete pit made with 40mm thick cover of RCC 1:2:4 reinforced with XPM (Weight not less than 4Kg/Sqm) and frame of angle iron 40x 40x6 mm and handle of 6mm dia MS bar made to shape, GI light grade 20mm bore pipe for watering perforated at bottom, 1.75meter long placed on top edge of earth plate, common salt & charcoal filling with fixing arrangement, funnel, wire mesh and earth work in hard/dense soil, returing filling in and removal of surplus soil to a distance not exceeding 50 meters all as per electrical plate No -5 of SSR 2009 Part-I and connecting to Lighting protection earth test points all as specifed and directed including testing on completion.

Supply & Laying & commissining of LT UG cable XLPE sheathed PVC insulated, screened PVC bedded, galvanised steel strip of wire armoured electric power cable heavy duty with stranded aluminium conductor 1100 volts grade, laid in tranches, in GI pipe, including brass cable glands, clamps etc of size 2 core x 10 Sqmm complete all as specifed and as directed. Make : Polycab/KEI/Havells Note: Earthwork, sand cushioning, bricks, GI pipe, etc will be measured and pad under appropriate items.

Supply and Laying Double wall corrugated pipe(DWC pipe, Specification-40 mm OD/32 mm ID) for laying XLPE LT UG cable by DWC pipe throughout the LT cable length in pieces of convenient lenth .(Note : in pieces for easy rectification during fault ).

Supplying and laying un-reinforced precast concrete cable cover, class Class LV, Type I, flat, size 250mm x 150mm x 40mm complete all as specified and directed by Engr-in-charge

M&L for Sand Cushioning (dry) in trenches/ducts for protection of UG Cables (below, above and around the UG Cable laid in Trenches) of 23 cm spread thickness (8 cm in depth before laying the cable and 15 cm in depth after laying the cable) and consolidated (punned) upto 180 mm thickness, complete all as specified and as directed. Note : For the purpose of payment, punned thickness of sand cushioning only shall be measured and paid for.

Supply and fixing GI Pipe light grade of Size 40mm bore with all fittings for passing of cables fixed to pole/wall/laid under floor or roads including all fixing accessories complete for protection of cable all as specified and directed. Make: Jindal/ Bansl/Tata

Supply, laying and jointing GI tubes, medium grade 20mm dia in lengths with screwed and socket joints together with all galvanised steel fittings such as bends, elbows, tees, union, short pieces, connectors, check nuts, caps, plugs etc fixed complete laid in trenches complete all as specified and directed by Engr-in-charge.

Cutting existing pipe DI/CI/GI/ and insertion of DI Tee of suitable size complete all as specified and directed by Engr-in-charge.

S&F Gun metal gate valve 20mm bore with iron wheel head screwed both ends for iron pipes complete all as specified and directed .

SUBHAM ENTERPRISES (BID ID -3426154)

KAMLA CONSTRUCTION COMPANY (BID ID -3418228)