REPAIR AND MAINT OF SUBMERSIBLE AND CENTRIFUGAL PUMP SETS, LT PANEL RELATED DISTRIBUTION SYSTEM, REPAIR MAINT OF SWIMMING POOL EQUIPMENT AND ALLIED WORK OF AGE E/M (W) UNDER GE (WEST) JABALPUR

Amount

Taking down centrifugal pump from existing foundation by disconnecting electrically and mechanically at different locations, transporting it to the workshop, dismantling the pumps set & carrying out for repair / maintenance cleaning of inside pump, oiling, greasing, gland packing, filing of varnishing & for proper alignment including replacement of un-serviceable parts with new ones and refixing existing location after got repaired maintenance / replacement of parts, re-assembling on foundation including replacement of nut, bolt and washers fixing in existing position commissioning and testing including loading / unloading, transportation to and from workshop for pumps of following capacity of any size:- Note : (a ) The cost of transportation such as vehicle , T & P and man power deemed to be included in the rate quoted by the contractor) (b) Winding may be measured and paid separately. (c) Supply only spare parts as mentioned in here-in-after.

(b) 60 HP to 75 HP

(c) 25 HP to 35 HP

(d) 7.5 H to 15 HP

(e) 3 HP to 5 HP

M&L for dismantling of centrifugal motor after disconnecting electrically and mechanically, transporting to workshop for Comprensive repair and maintenance including loading/unloading and reassembling after necessary repair and rewinding the motor stator/rotor with supper enameled copper winding wire of existing size , gauge and turns etc including Spare parts , all the insulating material i.e. varnish, supper high quality cotton tape, insulating paper or soldering etc. including drying up to desired temperature for specific time complete all as specified and directed by Engr-in-Charge for the following capacity of any size :- Note : (i) Rewinding warranty of centrifugal pump shall be of 06 months from installation (ii) UNSV PUMP/ Motor should be attend on the same day and re installed within 48 Hours incl Sunday and holyday when and after intimation for failure of motor (iii) A recovery Rs 1000 per day for Late Installation/ not attend the centrifugal motor

(b) 60 HP to 75 HP

(c) 25 HP to 40 HP

(d) 7.5 H to 15 HP

(e) 3 HP to 5 HP

Material & Labour for painting of centrifugal pump set with one coat of synthetic enamel paint of approved colour or shade as approved by Engineer-in-Charge including preparation of surface after removing existing paint & filling depressions complete all as specified & directed by Engineer - in - Charge including writing of SM No. and MES No. on the pump set for the following capacity:-

(b) 60 HP to 75 HP

(c) 25 HP to 40 HP

(d) 7.5 H to 15 HP

(e) 3 HP to 5 HP

Supply only of following parts of Centrifugal pump set of capacity 100 HP :-

(a) Ball bearing for motor of existing size

(b) Ball bearing pump set of existing size

(c) Impeller made out of brass of existing size

(d) Glands bush

(e) Neck Ring

(f) Coupling complete of existing size

(g) Pump shaft including key

(h) Rubber bush including nut bolt and washer complete

(j) Sleeves

Supply only of following parts of Centrifugal pump set of capacity 40 to 75 HP :-

(a) Ball bearing for motor of existing size

(b) Ball bearing pump set of existing size

(c) Impeller made out of brass of existing size

(d) Glands bush

(e) Neck Ring

(f) Coupling complete set of existing size

(g) Pump shaft including key

(h) Rubber bush including nut bolt and washer complete

(j) Sleeves

Supply only of following parts of Centrifugal pump set of capacity 25 to 35 HP :-

(a) Ball bearing for motor of existing size

(b) Ball bearing pump set of existing size

(c) Impeller made out of brass of existing size

(d) Glands bush

(e) Neck Ring

(f) Coupling complete set of existing size

(g) Pump shaft including key

(h) Rubber bush including nut bolt and washer complete

(j) Sleeves

Supply only of following parts of Centrifugal pump set of capacity 7.5 to 15 HP :-

(a) Ball bearing for motor of existing size

(b) Ball bearing pump set of existing size

(c) Impeller made out of brass of existing size

(d) Glands bush

(e) Neck Ring

(f) Coupling complete set of existing size

(g) Pump shaft including key

(h) Rubber bush including nut bolt and washer complete

(j) Sleeves

Supply only of following parts of Centrifugal pump set of capacity 3 to 5 HP :-

(a) Ball bearing for motor of existing sizes and make.

(b) Ball bearing pump set of existing size

(c) Glands bush

(d) Neck Ring

(e) Coupling complete set of existing size

(f) Pump shaft including key

(g) Rubber bush including nut bolt and washer complete

(j) Sleeves

Submersible Pump Taking out Submersible Pump Set at different locations along with Column pipe of 80 to 100 mm bore with Submersible cable from the bore well of depth ranging for 30 Mtr to 90 Mtr and transporting it to work shop for dismantling / opening for repair & taking out unserviceable parts of capacity 10 to 35 HP including loading/ unloading and transportation to and from work shop complete all as specified and as directed. Note : Supply only of spare parts shall be measured and paid separately

Lowering and re-fixing of submersible pump set of 7.5 HP to 35 HP at different locations including pump set installation, commissioning and testing after repair & replacement of un-serviceable parts with existing coloumn pipe 80/100mm bore with existing serviceable cable including tightening of rope to the pump by suitable arrangement of chain pulley system and connection with starter electrically and connection with pipe line mechanically complete all as specified and as directed.

M&L for rewinding the motor stator/rotor with supper enameled copper winding wire of existing size and gauge and turns etc including all the insulating material i.e. varnish, supper high quality cotton tape, insulating paper or soldering etc. including drying up to desired temperature for specific time complete all as specified and directed by Engr-in-Charge of the following capacity of submersible pump:- Note : (i) Rewinding warranty of submersible pump shall be of 06 months. (ii) UNSV PUMP/ Motor should be installed within 24 Hours when and after intimation for failure of motor (iii) A recovery Rs 1000 for Late Installation of pump (iv) Before installation of motor / Pump , it should be ensure that all unsv spare parts of Motor / Pump as given below are replaced (v) Spare parts will measure and paid separately

(c) 20 HP to 22.5 HP

(d) 15 HP to 17.5 HP

(e) 5 HP to 12.5 HP

S&F in repairs following parts of Submersible Motor 7.5 HP to 35 HP capacity suitable for any size of dia :-

(a) Motor bearing bush

(b) Motor base complete

(c) Motor base plate

(d) Bearing Upper Housing

(e) Bearing Lower Housing

(f) TB axial

(g) RT Disc

(h) Upper/ lower Flange

(j) Cable joint

(k) Starter Circlip

(l) Rotor circlip

(m) Motor Coupling

(n) Rotor sleeve

(o) Water seal 'O' Ring

(p) Upper/Lower Flange stud

(q) TB Housing

(r) Adopter stud

(s) Water seal

(t) T Bolt upper/ lower

(u) Stud O Ring

(v) sand guard

(w) Pressure cup equalizer

(x) Rocker

(y) Coupling Key

(z) C I Bearing

(aa) Cable clip

(ab) Drain plug

(ac) Stud

(ad) Balancing ring

(ae) Rotor nut

S&F in repairs following parts of Submersible Pump 7.5 HP to 35 HP capacity suitable for any size of dia :-

(a) Neck Ring

(b) Bearing bush

(c) Bearing sleeve

(d) Impeller

(e) Stage Casing

(f) Suction Housing

(g) Distance sleeve

(h) Pump Coupling

(j) Locking screw

(k) Stainer

(l) DOL bush

(m) DOL Sleeve

(n) Distance bush

(o) Body Nut

(p) Body stud

(q) Pump Shaft

(r) Pump Shaft Key

(s) Intermediate piece

(t) Intermediate sleeves

(t) Suction housing bush

(u) Stem

(v) NRV body

M&L for Rotor Machining, Grinding & balancing of any capacity Pump.

M&L Impeller Machining & Balancing of any capacity pump.

Material & Labour for replacement of rotor of the submersible motor 3 phase 415 Volt 50 Hz AC for following capacity:-

(c) 20 HP to 22.5 HP

(d) 15 HP to 17.5 HP

(e) 7.5 HP to 13 HP

M& L for replacement of stator of the submersible motor 3 phase 415 volts 50 Hz AC for following capacity of any size :-

(c) 20 HP to 22.5 HP

(d) 15 HP to 17.5 HP

(e) 7.5 HP to 13 HP

M&L in replacement Air release valve of size 80mm bore with two air outlet conforming to IS 14845 and fixing up ,complete all as specified and directed.

Supply & lowering of GI Heavy duty column pipe 100mm (4" bore), 3 Mtr long , ISI marked with 100mm long threaded socket heavy duty for lowering of submersible pump in bore well complete all as specified and as directed. Make : TATA/Jindal /BST

Supply & lowering of GI Heavy duty column pipe 80mm (3" bore), 3 Mtr long , ISI marked with 100mm long threaded socket heavy duty for lowering of submersible pump in bore well complete all as specified and as directed. Make : TATA/Jindal /BST

Cutting and threading 80mm (3" bore) both end MS / GI column pipe heave duty 3 Mtr long including heavy duty new socket 80mm bore 100 mm long complete all as specified and directed.

Cutting and threading 100mm (4" bore) both end MS / GI column pipe heave duty 3 Mtr long including heavy duty new socket 80mm bore 100 mm long complete all as specified and directed.

S&F Lowering, Commissioning & testing of submersible pump set of capacity 20HP, 415 Volts, 50 Hz, not less then 180 Mtr head, 250 LPM to 750 LPM with delivery size of 100mm bore including lifting of old UNSV submersible pump and deposited to W/S store yard, complete all as specified and as directed by Engineer-in-Charge. Make Kirloskar/KSB/ Crompton.

S&F Lowering, Commissioning & testing of submersible pump set of capacity 15HP, 415 Volts, 50 Hz, not less then 150 Mtr head, 250 LPM to 750 LPM with delivery size of 100mm bore including lifting of old UNSV submersible pump and deposited to W/S store yard, complete all as specified and as directed by Engineer-in-Charge. Make Kirloskar/KSB/ Crompton.

S&F in repairs PVC Insulated and PVC sheathed Industrial 3 Core Flat Submersible cable 4 sqmm with bare bunched copper conductor for submersible pump motor with voltage grade 1100 volts as per IS 694/1990 including jointing connecting with submersible motor to starter including removing old submersible cable complete all as specified and directed. Polycab or equivalent in RPG/ Havells

S&F in repairs PVC Insulated and PVC sheathed Industrial 3 Core Flat Submersible cable 6 sqmm with bare bunched copper conductor for submersible pump motor with voltage grade 1100 volts as per IS 694/1990 including jointing connecting with submersible motor to starter including removing old submersible cable complete all as specified and directed. make Polycab or equivalent in RPG/ Havells

S&F in repairs PVC Insulated and PVC sheathed Industrial 3 Core Flat Submersible cable 10 sqmm with bare bunched copper conductor for submersible pump motor with voltage grade 1100 volts as per IS 694/1990 including jointing, connecting with submersible motor to starter including removing old submersible cable complete all as specified and directed. make Polycab or equivalent in RPG/ havells

Material & Labour for PCC 1:2:4 type B-1 using 20mm graded crushed stone aggregate size as in thrust block / support pillar for pipe holding with MS clamps 50 x 6 mm including finishing the concrete surface fair and even with out using extra cement making good to disturbed surfaces complete.

S&F Commissioning & testing of centrifugal pump set with motor of capacity 15HP, 415 Volts, 50 Hz, not less then 50 Mtr head, 250 LPM to 400 LPM with delivery/ discharge size of 100mm bore, complete all as specified and as directed by Engineer-in-Charge. Make Kirloskar/KSB/ Crompton.

M&L for fittings for spigot socketed cast iron pipes 80 to 300mm bore such as bends (any type, radius and angle), tapers any type (straight, bend, increasing, decreasing or double socket etc), tee pieces, single branch, 'Y' junction, double branch, cross (all sockets or socket and spigot), collars, caps and plugs complete all as specified and as directed.

M & L for MS clamps for suitable sizes from flat iron/ structural steel sections as per site requirement including nuts, bolts, washers, welding, bending cold or hot, drilling holes bolts, sockets etc any shape o size complete all as specified and as directed.

S & F nylon wire rope 10 Sqmm of PVC coated water proof for holding motor pump set complete all as specified and as directed.

Supply, install, test and commissioning submersible pump starter fully automatic star delta starter in sheet metal enclosure type MUG-20 mortar, 28 to 42 Amp relay max. range rating AC 3 Phase 415 Volt 50 HZ conforming to IS/ IEC : 60947-41 protection offered overload single phasing, phase reversal, phase imbalance, auto restart features vibration proof enclosure with IP-54 protection class indications offered ON/ OFF voltage and Ampere complete all as specified and as directed. Make : L&T/ ABB/ C&S/ Crompton/ Schneider

Supply, install, test and commissioning submersible pump starter fully automatic star delta starter in sheet metal enclosure type MUG-30 mortar, 30 to 50 Amp relay max. range rating AC 3 Phase 415 Volt 50 HZ conforming to IS/ IEC : 60947-41 protection offered overload single phasing, phase reversal, phase imbalance, auto restart features vibration proof enclosure with IP-54 protection class indications offered ON/ OFF voltage and Ampere complete all as specified and as directed. Make : L&T/ ABB/ C&S/ Crompton/ Schneider

Supply, install, test and commissioning submersible pump starter fully automatic star delta starter in sheet metal enclosure type MUG-40 mortar, 30 to 50 Amp relay max. range rating AC 3 Phase 415 Volt 50 HZ conforming to IS/ IEC : 60947-41 protection offered overload single phasing, phase reversal, phase imbalance, auto restart features vibration proof enclosure with IP-54 protection class indications offered ON/ OFF voltage and Ampere complete all as specified and as directed. Make : L&T/ ABB/ C&S/ Crompton/ Schneider

S & F DOL starter 240/ 415 volt suitable for 3 to 5 HP motor pump set as per requirement at site complete all as specified and as directed.

Repair/ maintenance of Decrin Dozer and replacing defective parts/ spares including testing and commissioning complete all as specified and directed. Note : Quoted rates for spares are inclusive of repair/ replacement of Decrin Dozer.

(a) Roller assembly (PK-4)

(b) Pump tube (PK-5)

(c) Weighted suction line strainer 3/8"

(d) 3/8" white suction / discharge tube

(e) Check valve duckbill only (PK-5)

(f) Connecting nut 3/8"

(g) connecting nut 3/8" with adapter (PK-5)

(h) GI fitting for Doser including gate valve

(j) NRV suitable for Decrin Dozer

Supply and fixing in repairs water meter pressure gauge with float body including steel wire cable, ball bearing, rollers, MS clamp & nut, bolt and washers etc all complete.

Taking down / out old unserviceable cable from trenches / ducts or taking down from pole / wall including disconnecting electric connection of any size any type & removing from site complete.

Supply, laying or fixing or passing through pipe commissioning and testing XLPE Insulated screened PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 50 Sqmm 3.5 core including taking down/out old UNSV cable from trenches/ducts/from pole/wall removing from site etc complete all as specified & directed.

Supply, laying or fixing or passing through pipe commissioning and testing XLPE Insulated screened PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 35 Sqmm 3.5 core including taking down/out old UNSV cable from trenches/ducts/from pole/wall removing from site etc complete all as specified & directed.

S&F in repair testing and commissioning PVC unsheathed flexible copper cable 1100 volts grade of size 2.5 Sqmm (three runs of single core). Complete all as specified and as directed

Supplying and fixing in repair 1100 volts grade heavy duty cable PVC insulated aluminium conductor served with inner sheeting of PVC tape and overall PVC sheathed in service connection, twin core 10 Sqmm stranded aluminum conductor cable flat or circular complete including dismantling of existing service connection all as specified and directed.

Material & Labour for earthing complete with galvanised steel earth plate electrode 600X600X6mm thick buried directly in ground (Earth pit not less than 2.25 mtr deep below the ground level with top edge of earth plate not less than 1.5 mtr below normal ground level) connected to galvanised earth wire 4mm as earthing lead by means of bolts, nuts, check nuts and washers of GI or steel complete as shown in electrical plate No 3 of SSR-2009 (Part-I) including charcoal dust common salt, 20mm bore GI medium grade watering pipe with funnel along with wire mesh, including 15mm dia GI pipe light grade [Minimum 5 m in length] for protection of GI earth wire, including PCC pit 1:2:4 type B-1 using 20mm graded crushed stone aggregate with angle iron 40X40X5mm frame 60mm thick RCC cover with 8mm dia TMT steel bars spacing @ 100 mm centre to centre both ways i.e. horizontal and vertical complete all as directed by Engineer-in-charge and testing for required value complete. Note:- If earth resistance of earthing is not found satisfactory it will be redone by the contractor on his risk and cost.

Supply and fixing in repair MCCB 4 pole 63 Amps , 415 volts rupturing capacity 16KA on LT panel/feeder pillar box etc complete all as specified and directed. Make : Schenider/ Havells/ L&T

Supply and fixing in repair MCCB 4 pole 100 Amps , 415 volts rupturing capacity 16KA on LT panel/feeder pillar box etc complete all as specified and directed

Supply and fixing in repair MCCB 4 pole 160 Amps , 415 volts rupturing capacity 16KA on LT panel/feeder pillar box etc complete all as specified and directed

Supply and fixing in repair MCCB 4 pole 250 Amps , 415 volts rupturing capacity 16KA on LT panel/feeder pillar box etc complete all as specified and directed

Supply and fixing in repair MCCB 4 pole 400 Amps , 415 volts rupturing capacity 16KA on LT panel/feeder pillar box etc complete all as specified and directed

Repair / Servicing of LT panel board with starter all model MUG of L&T of submersible pump in each pump house including making fresh connections of cables, new lugs, painting of LT panel, cleaning etc complete all as specified & as directed

Testing of water sample obtained in bore wells/ swimming pool from Authorised Test Laboratory as directed

Supply & Fixing in replacement of terminal plate with 06 Nos copper lugs suitable for 35/50 Sqmm copper cable 3.5 core for 100 HP pump set complete all as specified and as directed.

S&F 15mm bore bib tap cast copper alloy with crutch/butterfly handle screwed for iron pipe complete all as specified. Make - Prayag/Sieko/Cornett

Excavation in trenches not exceeding 1.5m deep & not exceeding 1.5m wide or area not exceeding 10 Sqm on plan, in any type of soil and getting out for foundation, trenches or laying of electric cable or pipes complete all as specified & directed.

Returning, filling in, excavated soil including spreading, leveling, watering and well ramming in layers not exceeding 25cm thick complete all as specified and directed.

Removal of excavated materials (soil) to a distance not exceeding 50 m and depositing where directed at a level not exceeding 1.5 m above the starting point complete all as specified & directed.

Supply and laying sand cushioning with dry and clean washed sand over and under the under ground cable in trenches, ducts for cable protection 150 mm below & 80 mm above the cable as protection of cable complete as specified & directed. Note : Punned thickness of sand shall be measured & paid.

Supply and laying Best quality locally available, sub class B bricks (Old size) for cable protection cover laid flat and dry in trenches over the cable perpendicular to the direction of the cable complete all as specified and as directed by Engineer-in-charge.

Supply of chemical TCCA-90 (Trichloroisocyanuric) acid granule form, organic compound for swimming pool complete all as specified and as directed

S&F in repair changer over switch 4 pole 200 Amp, 415 Volts, Onload type, front handle type with enclosure including connection and testing complete all as specified and directed. Make-Havells /Legrand / L&T

S&F in replacement the LED rechargeable emergency search light slim ray suitable for 240 volts charging system complete with all respect all as required and directed at site make Philips slim ray or equivalent Bajaj

Supply and fix in replacement of CI sluice valve with forged brass stem class PN- 1.0 ISI marked with stainless steel spindle and flanged both ends of size 80 mm dia bore with hand wheel confirming to IS 14846/2000 and its fittings suitable for hydraulic test pressure of 15 Kg/sqcm complete all as specified and directed. Make;KIRLOSKER/UPADHYAY/VENUS / L&T

All as described in serial item No. 62 above, but for 100 mm bore.

All as described in serial item No. 62 above, but for 150 mm bore.

All as described in serial item No. 62 above, but for 200 mm bore.

Dismantling of existing valve pit and M&L for construction of masonry valve pit with the following specification:- Brick work in CM (1:4) with sub class 'B' bricks, 15mm thick plastering in CM (1:4), PCC (1:4:8) type D-2 in foundation, chamber of internal size 1200 x 1200x1200 mm,150mm thick copping on top in PCC (1:3:6), type C-1, 3mm thick MS sheet for cover, angle iron 40mmx40mmx5mm for frame all around with suitable handle with locking arrangement including two coats of synthetic enamel paint over a coat of red oxide primed on MS work and three coats of white wash and preparation of surfaces complete all as specified and shown on drawing

Dismantling of existing valve pit and M&L for construction of masonry valve pit with the following specification:- Brick work in CM (1:4) with sub class 'B' bricks, 15mm thick plastering in CM (1:4), PCC (1:4:8) type D-2 in foundation, chamber of internal size 900 x 900x1200 mm,150mm thick copping on top in PCC (1:3:6), type C-1, 3mm thick MS sheet for cover, angle iron 40mmx40mmx5mm for frame all around with suitable handle with locking arrangement including two coats of synthetic enamel paint over a coat of red oxide primed on MS work and three coats of white wash and preparation of surfaces complete all as specified and shown on drawing

Material and labour in replacement of control wiring/ motor starter wiring of pump motor starter panel with PVC insulated copper contactor of sizes 4/6/10/50/70 sqmm all as specified and directed.

Supply only in replacement of MS Nut bolts machine made with hexagonal or square head at one end screwed the other, each screws and to be fitted with washers and nut, exc 5 cm but not exc 10 cm long and dia of bolt 10cm complete all as specified and directed.

Supply only plastic heavy duty bucket 30 ltr for chlorination with mug complete all as specified and as directed

Material and labour in replacement for MS tail piece 6" dia length required on site both end flanged with nuts bolt and rubber flanged complete all as specified and directed.

Material and labour for Repair to pump house bore well cap cover made out from mild steel sheet 3 mm thick and angle iron frame in any shape and size complete with making holes , nut bolts welding etc as reqd at site including painting of two coat of synthetic enamel paint over a coat of red oxide complete all as specified and directed.

M & L in replacement CI non return valve of bore 150 mm dia ,ISI marked complete all as specified and as directed

M & L in replacement CI non return valve of bore 100 mm dia ,ISI marked all as specified and directed

Attending external water supply complaint by excavation in soft/dense soil & taking up pipe /fitting of size 80 to 200 mm dia GI/PVC cutting, rethreading/jointing the pipe and replacing unserviceable fitting returning and filling the excavated soil and testing the joint Note : Necessary Excavation up to 0.60 cum shall be included in the job ' complete all as specified and directed.

S&F in replacement of the following stainless steel spindle suitable for following dia of sluice valve complete with stainless steel nut and threading as per sample & directed by engr-in- charge

200mm bore sluice valve

150mm bore sluice valve

100mm bore sluice valve

80mm bore sluice valve

M&L in replacement Gun metal globe/gate valve (ISI Marked) with iron wheel head, screwed both ends for pipes or for unions for 50mm bore dia steel tubing complete all as specified and as specified and as directed by Engr-In- Charge

All as described in serial page No. 81 above, but for 40 mm bore

All as described in serial page No. 81 above, but for 25 mm bore

All as described in serial page No. 81 above, but for 20 mm bore

M & L for dismantling , opening of any type of submersible pump set 1 HP to 2 HP of any stage/size/make and re-assembling the pump after rewinding, repair/replacement of the defective parts of pump/motor and relaying complete , testing all as specified and as directed by Engr-In- Charge

Supply only gland packing of size 10/15/20mm

Material & labour in replacement for chlorine test kit with coloured sample complete with all testing fitments and OT solution in rexene finish box complete all as specified and as directed by Engr-In- Charge.

Supply only OT solution for chlorine test 500 ML bottle

S&F rubber gasket joint for flanged end pipe & fittings of size 80mm dia to 200mm dia complete all as specified and as directed by Engr-In- Charge.

Material & labour for cleaning away all grass vegetation, scalping shrubs bushes under growth roots and trees up to zero level not exceeding 30 cm girth and removing rubbish up to distance of 50 mtr out the periphery of area under cleanness complete with tractor/JCB plants/ Manpower complete all as specified and as directed by Engr-In- Charge.

Material and Labour for road cutting, including excavation, returning filling in, spreading, leveling, well ramming in layers, soiling with broken boulders/stones, WBM 7.5 cm thick coarse aggregate received from dismantling the existing road, premix, carpeting 25 mm thick using ready mix patch mate material, rolled and compacted for road patch repair work complete all as specified and directed.

Material and labour in replacement Run lead joint complete with spun yarn packing & filling properly with lead pig of 200 mm dia/bore pipe , complete all as specified and as directed

M&L in replacement Run lead joint complete with spun yarn packing & filling properly with lead pig of 150 mm dia/bore pipe , complete all as specified and as directed

M&L in replacement Run lead joint complete with spun yarn packing & filling properly with lead pig of 100 mm dia/bore pipe , complete all as specified and as directed

Supply and laying of GI steel tubing 80mm bore medium grade with replacement of US fittings laid in tranches/wall/floor and joined including necessary fittings such as bends, elbow, tees sockets etc including necessary saddles and clamps complete all as specified and directed.

All as described in serial item No. 95 above, but for 50mm bore

All as described in serial item No. 95 above, but for 40mm bore

All as described in serial item No. 95 above, but for 25mm bore

All as described in serial item No. 95 above, but for 20mm bore

S&F in replacement of U/S electronic timers 380/415V, 50Hz range 3-10,9-30 , 30 -120 sec complete all as specified and directed by Engr-in-charge. Make :L&T /ABB /C&S

S&F in replacement of U/S Volt meter / Ampere meter as suitable existing approx CT ratio-100/5 & 30/5 complete all as specified and directed by Engr-in-charge. Make L&T/Schneider/ABB

S&F in replacement of U/S LED indicator lamp (green , red , yellow ) 220V 50Hz complete all as specified and directed by Engr-in-charge. MAKE : L&T /C&S/ABB

S&F in replacement of U/S ON/OFF push button complete all as specified and directed by Engr-in-charge. Make L&T /C&S/ABB

S & F Power contactor MUG 2 , 3 pole rating not less than 32 A with 230 coil complete all as specified. Make L&T/Schneider

S & F Power contactor ML-2, 3 pole rating not less than 40 A with 230 coil complete all as specified. Make:L&T/Siemens/Schneider

S & F Power contactor MNX 110 , 3 pole rating not less than 100 A with 415V complete all as specified. Make:L&T/Siemens/Schneider

S & F Power contactor MNX 140 , 3 pole rating not less than 100 A with 415V complete all as specified. Make:L&T/Siemens/Schneider

S&F thermal protection overload RELAY with built in earth fault relay ,, 20 to 32 amp, 230/415V coil complete all as specified. Make:L&T/Siemens/Schneider

S&F thermal protection over load RELAY with built in earth fault relay , 28 to 45 amp, 230/415V coil complete all as specified. Make:L&T/Siemens/Schneider

S&F Thermal protection over load RELAY with built in earth fault relay, 66 to 110 amp, MN5 up to 500V complete all as specified. Make:L&T/Siemens/Schneider

S&F Swimming pool suction hose pipe ISI Mark 40/ 50mm bore dia with ISI mark complete all as specified &as directed by Engineer In Charge. Make :- Kishan or Equivalent

M & L in replacement Foot valve of bore 100 mm dia ,ISI marked including all fitting , nut , bolt etc complete all as specified and directed

M & L in replacement Foot valve of bore 150 mm dia ,ISI marked including all fitting , nut , bolt etc complete all as specified and directed .

Supply only Calcium based granual dis infectant for water treatment more stable than chlorine gas and stronger than bleaching powder and Calcium Hypo chlorite 65% to 70% Chlorine content in granular (Packing in 45 Kg Plastic drum) complete all as specified and as directed by Engr-In- Charge

Supply & testing of submersible pump starter fully automatic star delta starter in sheet metal enclosure type MN 110F motor, 30-50 Amp relay max range rating AC 3 phase 415 Volt 50 Hz conforming to IS / IEC : 60947-41 protection offered overload single phasing, phase reversal, phase imbalance, auto restart features vibration proof enclosure with IP-54 protection class indications offered ON / OFF Voltage and ampere complete as specified & directed by Engineer-in-Charge.

M & L for taking out motor from non clog sewage submersible pump Dismantling the burn motor, Rewinding the motor with as per existing gauge size of copper winding wire by super enameled copper wire, including insulation material cotton tape, varnish , insulation paper , sleeves and dry & backing etc connections etc and assembling complete after duly repair installation commissioning and testing up to the good working performance of the following capacities including replacing bearing for NDE & DE side of motors of following HP, 3 Phase 415 Volt all as specified and directed. Note : (i) Rewinding warranty of centrifugal pump shall be of 06 months. (ii) UNSV PUMP/ Motor should be attend on the same day and installed within 24 Hours including Sunday and holiday when and after intimation for failure of motor (iii) A recovery Rs 1000 per day for Late Installation of pump / not attend the motor/pump (iv) The cost of transportation such as vehicle , T & P and man power deemed to in this job

M K ENTERPRISES

RP ANAND