Construction of Electric Crematorium at Kolara CMC and KGF CMC under UIDF scheme

Construction of Electric Crematorium at Kolara CMC under UIDF scheme

Earth work excavation by manual means for drains, canals, waste weir, draft, approach channels, key trenches, foundation of Buildings & bridges and such simillar works in all kinds of soils, as per dr...

Earth work in surface excavation by mechanical means for lowering & leveling the ground for all works other than foundation in all kinds of soils & upto depth not exceeding 300mm as per drawing and te...

Earth work excavation for Foundation by mechanical means for all works & depth upto 3 m, as per drawing and technical specifications, including setting out, shoring, strutting, barricading, caution li...

Earth work excavation for Foundation by mechanical means for all works & depth upto 3 m, as per drawing and technical specifications, including setting out, shoring, strutting, barricading, caution li...

Providing and injecting chemical emulsion for Pre-constructional Anti-Termite Treatment, creating continuous chemical barrier under and around the column pits, walls, trenches, basement excavation, to...

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations and other similar works etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by r...

Construction of Embankment by excavating the available approved Gravel/ Murrum deposited at a place or borrow pits during or prior excavation with all lifts and lead, transportation to site, spreading...

Removal of Unserviceable Soil with Disposal upto a suitable distance as directed by the Engineer incharge of work. I.No.3.1, P.No.17, [Vol-3], KPWD SR 2023-24

Providing and laying in position Cement Concrete for levelling course for all works in foundation. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes...

Providing and laying in position Cement Concrete for levelling course for all works in foundation. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes...

Providing and laying in position Cement Concrete for levelling course for all works in foundation. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes...

Providing and laying in position Cement Concrete for all Foundation works. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed with supe...

Providing and laying in position Cement Concrete for all Foundation works. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed with supe...

Providing and laying in position Cement Concrete for all Foundation works. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed with supe...

Providing and laying in position Cement Concrete for all Sub structures of building, Irrigation works, Sub structure works of bridges, Drain works & other parallel works from 0.50m to 3.50 m height. T...

Providing and laying in position Cement Concrete for all Super structures of building , Road works, Water works, Irrigation works & super structure works of bridges upto 3.50 m height. The granite/tra...

Providing and laying in position Cement Concrete for all Super structures of building , Road works, Water works, Irrigation works & super structure works of bridges upto 3.50 m height. The granite/tra...

Providing and laying in position Cement Concrete for all Super structures of building , Road works, Water works, Irrigation works & super structure works of bridges upto 3.50 m height. The granite/tra...

Providing and laying in position Cement Concrete for all Super structures of building , Road works, Water works, Irrigation works & super structure works of bridges upto 3.50 m height. The granite/tra...

Providing and laying in position Cement Concrete for all Super structures of building , Road works, Water works, Irrigation works & super structure works of bridges upto 3.50 m height. The granite/tra...

Providing and laying in position Cement Concrete for all Super structures of building , Road works, Water works, Irrigation works & super structure works of bridges upto 3.50 m height. The granite/tra...

Providing and laying in position Cement Concrete for all Super structures of building , Road works, Water works, Irrigation works & super structure works of bridges upto 3.50 m height. The granite/tra...

Providing and laying in position Cement Concrete for all Super structures of building , Road works, Water works, Irrigation works & super structure works of bridges upto 3.50 m height. The granite/tra...

Providing and laying in position Cement Concrete for all Super structures of building , Road works, Water works, Irrigation works & super structure works of bridges upto 3.50 m height. The granite/tra...

Supplying, fitting and placing TMT FE 550 / 550D Steel Reinforcement including cost of all materials, machinery, labour, cleaning, straightening, cutting, bending, hooking, laping/welding joints, tyin...

Providing Size Stone masonry with hard stone in foundation & plinth with Cement mortar 1:6 (1 cement : 6 coarse sand) I.No.5.4, P.No.9, [Vol-2], KPWD SR 2023-24

Providing Brick work with common burnt clay Non Modular bricks of class designation 3.5 in superstructure above plinth level in all shapes and sizes in Cement mortar 1:4 (1 cement : 4 coarse sand) inc...

Providing Half brick masonry with common burnt clay Non Modular bricks of class designation 3.5 in superstructure above plinth level up to floor 1 level cement mortar 1:3 (1 cement :3 coarse sand) inc...

Providing 18 mm cement plaster in two coats under layer 12 mm thick cement plaster with cement mortar 1:5 (1 cement : 5 coarse sand) and a top layer 6 mm thick cement plaster with cement mortar 1:3 (1...

Providing 20 mm cement plaster of mix 1:4 (1 cement:4 fine sand) to brick/stone masonry including rounding off corners wherever required smooth rendering, providing and removing scaffolding, including...

Providing 12 mm cement plaster finished with a floating coat of neat cement of mix :1:4 (1 cement: 4 fine sand) to brick masonry including rounding off corners wherever required smooth rendering, prov...

Providing 12 mm cement plaster finished with a floating coat of neat cement of mix :1:3 (1 cement: 3 fine sand) to brick masonry including rounding off corners wherever required smooth rendering, prov...

Providing 15 mm cement plaster on the rough side of single or half brick wall of mix :1:6 (1 cement: 6 fine sand) including rounding off corners wherever required smooth rendering, providing and remov...

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete as per sp...

Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound) content. With water thinnable cement primer on wall surface having VOC content less tha...

Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade :Two coats on new work after thoroughly brooming the surface to remove all dirt, dust, mortar drops an...

Painting wood work with Deluxe Multi Surface Paint of required shade. Two coat applied @ 0.90L/10 Sqm over an under coat of primer applied @0.75 L/10 Sqm of approved brand and manufacture to give an e...

Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two coat applied @ 0.90L/10 Sqm over an under coat of primer applied @ 0.80 L/10 Sqm of approved brand and manufacture includ...

Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives with pure Acrylic Resin, UV resistant, dirt & pick up resistant, Alkali & Water resistant of required shade: New work...

Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, e...

Providing skirting, dadooing, rises of steps with colour glazed tiles 6mm thick on 10mm thick cement plaster 1:3 and jointed with white cement slurry over existing rough plaster surface using glazed t...

Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 m...

Providing and laying flooring and steps fine machine polished granite stone slabs 20 mm thick on cement mortar bed 1:6, 20 mm thick, and joints finished with cement mortar 1:3 over existing cement con...

Providing and laying 52 mm thick cement concrete flooring with concrete hardener topping, under layer 40 mm thick cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nomin...

Providing and laying 60mm thick factory made cement concrete paver block of approved shape and colour of M -30 grade made of C&D waste by block making machine with vibratory compaction laid in require...

Providing and laying water proofing treatment to the Roof with PU based single component elastomeric pure polyurethane based coating on New terrace/Chajjas/Sunken portion of WC:Bathroom, cold applied ...

Providing Red Salwood frames of doors, windows, clerestory windows, ventilators and other frames, wrought, framed or assembled including making plaster groves (excluding cost of cement concrete and si...

Providing and fixing flush door shutter made out of solid core block board type, well seasoned , chemicaly treated hard wood battens and internal frame with minimum 45 mm wide wooden frame alround doo...

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid door/window/Clerestory windows & other Frames/ Chowkhat comprising of virgin PVC polymer of K value 58-60 (Suspensi...

Providing and fixing factory made Green certified, Anti Termite, UV resistant, high water absorbant single extruded WPC (Wood PolymerComposite) solid plain flush door shutter of required size comprisi...

Providing & fixing of 2-track x 2-panel sliding windows made out of multi chambered UPVC (Matching to RAL-9016) sections and with minimum TiO2(Titanium Dioxide) at 6PHR with TPE(Thermo Plastic Elastom...

Providing & fixing of louvered ventilator made out of multi chambered UPVC(Matching to RAL-9016) sections and with minimum TiO2(Titanium Dioxide) at 6PHR with TPE(Thermo Plastic Elastomer) and lead fr...

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. Fixed to openi...

Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on spec...

Providing and fixing ball bearing for rolling shutters including cost of materials, labour, usage charges of machinery complete as per specifications and as per directions of the Engineer-in-Charge. I...

Extra for providing mechanical device chain and crank operation for operating rolling shutters: Exceeding 10.00 Sqm and upto 16.80 Sqm in the area including cost of materials, labour, usage charges of...

Extra for providing Manually operated Bevel Gear Box for operating rolling shutters including cost of materials, labour, usage charges of machinery complete as per specifications and as per directions...

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitt...

Fixing of door frame in an existing opening including embedding frame in floor and walls after cutting masonry for holdfasts for embedding holdfast in cement concrete 1:3:6 of 20mm and down size grani...

Providing and fixing bright finished brass butt hinges with necessary screws etc. complete : 125x85x5.5 mm (heavy type) I.No.12.75.1, P.No.107, [Vol-2], KPWD SR 2023-24

Providing and fixing bright finished brass handles with screws etc. complete: Brass handles 125 mm with plate 175x32 mm I.No.12.79.1, P.No.108, [Vol-2], KPWD SR 2023-24

Providing and fixing chromium plated brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete. I.No.12.60, P.No.105, [Vol-2...

Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete : 250x10mm I.No.12.76.1, P.No.107, [Vol-2], KPWD SR 2023-24

Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete : 150x10mm I.No.12.76.3, P.No.107, [Vol-2], KPWD SR 2023-24

Chromium plated Brass screws 35 mm long SI.No.229, P.No.A-18, [Vol-2], KPWD SR 2023-24

Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 m...

Providing and fixing PTMT door catcher of length 72 mm and dia. of 42 mm with suitable washers weighing not less than 33 gms I.No.12.64, P.No.105, [Vol-2], KPWD SR 2023-24

Providing and fixing Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel et...

Line Supports (Pole) -RCC Pole - 9 Mtr Long, 150 Kg WL Sq Section (Dwg No. BESCOM/GM/QS&S/51 Dtd 24.11.2018) as per IS-785 Sl.No. 1, I.No. 1.01 , P.No. 3of 81, Vol-6, ESCOMs SR 2023-24

Cross Arms (MS & GI) as per IS-1977- 11 2.01 11 kV, Horizontal Cross Arm - Mild Steel (MS) (Dwg No. BESCOM/GM/QS&S/04 Dtd 24.11.2018) Sl.No2, I.No. 2.01 , P.No. 3of 81, Vol-6, ESCOMs SR 2023-24

7 ACSR Conductor as per IS-398 (Part - 2/1996) -Rabbit ACSR (6/3.35 mm Al + 1/3.35 mm St), Std Wt: 214 Kg/KM Sl.No59, I.No. 7.02 , P.No. 3of 81, Vol-6, ESCOMs SR 2023-24

Erection of Double Pole Transformer Structure using 9 Mtr Long RCC (145 Kg WL)/PSCC (300 Kg WL) Pole including fixing of Structure Materials, Erection of Poles etc., complete for mounting of Transform...

Compact RMU (VCB/SF6 Type) with Copper Busbar, 350 MVA, 630 Amps as per IEC 62271/IS-3427-3 Way RMU, 2 OD + 1 VL (One Incomer One Breaker + One Outgoing) As per ESCOM SR 2023-24 page no 16 of 81, SL N...

Distribution Transformer - 3 Phase, 11kV/433V - Stacked CRGO Core with Oil as per IS-1180 (Part-1): 201-A. OPEN BUSHING TYPE - 250 kVA, Aluminium Wdg, Star 2 (5 Star) As per ESCOM SR 2023-24 page no...

11 kV HT Metering cubicle of different CT Ratio, Both side cable entry type with 3 CT & 3 PT, With Transparent Cover TTB, with 30x8 mm Copper Busbar, Modem & 2 No of Meters for 3 Phase 4 Wire Metering...

LT PANEL - 1 Nos. 250kva Transformer- Supply, Installation, Testing and Commissioning of METER PANEL . 16 GAUGE CRCA SHEET panels including the cost of pedestals required to fix the panels shall be ...

LT PANEL - 1 Nos. 250kva Transformer- Supply, Installation, Testing and Commissioning of METER PANEL . 16 GAUGE CRCA SHEET panels including the cost of pedestals required to fix the panels shall be ...

Supplying & fixing miniature circuit breakers on existing MCB distribution boards using necessary fixing materials and C Type curve, indicator ON/OFF, energy cross-3 with Short circuit breaking capaci...

Supplying ......... A rated 3phase with neutral bus bar using required capacity electrolytic aluminium strips covered with heat shrinkable coloured PVC sleeve, mounted on phenolic/FRP/DMC insulator wh...

Supplying, fixing and wiring earth leakage relay with core balanced current transformer suitable for single phase 50 Hz AC with latest microcontroller based, digital readout of percentage leakage curr...

Supplying and fixing of LED type panel board indicating lamp with required colour suitable for 230/440VAC. 50 Hz 12/24V D.C. PWDElectrical SR 2023-24 - Page no - 19 of 105, Item no - 5.38

Supplying, fixing and wiring 3 Phase Digital Ammeter / Voltmeter PWDElectrical SR 2023-24 - Page no - 19 of 105, Item no - 5.29

Fabrication suppling and mountuing MS box, made out SWG suitable floor / wall mounting , fully weather proof with privision for better heat disspation , provided with hinged front cover, equipped with...

Supplying and fixing hylum plastic sheet 3 mm thick with necessary nitches for fixing switches, regulators etc., and fixing on existing wood or metal box using N. F. screws P. No. 9, Sl. No. 3.9, Vol-...

Supply and fixing of angle iron frame work fabricated out of ms angle iron,.. With bolts , washer, etc, and painted with 2 coat of red oxide and then two coats of approved paint. 75 x 75 x 6 mm P. No....

Supplying of four bucket stand along with buckets. Complete P.No.93, I.No.15.111 of KPWD S.R 2023-24 Vol-6

Supplying of Two bucket stand along with buckets. Complete P.No.93, I.No.15.112 of KPWD S.R 2023-24 Vol-6

Supplying of first aid box. Complete P.No.93, I.No.15.114 Vol-6 of KPWD S.R 2023-24

Supplying of FIRST AID CHART with lamination. Complete P.No.93, I.No.15.116 Vol-6 of KPWD S.R 2023-24

Supplying and installation of RUBBER MAT 1mtr x 1mtr -10mm thick. complete including cost of materials, labour, HOM complete as perspecifications. P.No.93, I.No.15.117 Vol-6 of KPWD S.R 2023-24

Supplying and laying of high tension 11KV Cable, dry curing & dry cooling with true triple extrusion, simaultaneously through sigle common head, 3 core under ground XLPE(E) cable having starandrad co...

Fixing of pot heads for HT cable only - Epoxy type P.No.120, I.No.22- I Vol-6 of KPWD S.R 2023-24

Supply and making 11KV ( E) Extruted X Linked for tubing & moulded and cross linked componets using heat shrinked stress control tube having high permittivity XLPE terminations - INDOOR & OUTDOOR ...

Supply and making 11KV ( E) Extruted X Linked for tubing & moulded and cross linked componets using heat shrinked stress control tube having high permittivity XLPE terminations - INDOOR & OUTDOOR ...

Main Control Panel Incoming (a) Supplying of on load change over switches 4 poles, AC-23A Duty, 415V, 50Hz, AC Supply....

Supplying and fixing Moulded Case Circuit Breaker (MCCB) over the existing wood/panel board using necessary screws, bolts, nuts, necessary phase separators, handle and wiring complete. Protection of O...

Supplying, fixing and wiring earth leakage relay with core balanced current transformer suitable for single phase 50 Hz AC with latest microcontroller based, digital readout of percentage leakage curr...

Supplying of multi function digital meter with three line back light LCD type display for voltage, Current, frequency, Power, power factor, KVA, KWH, KVAR suitable for 3 phase, 4 wire LT network with ...

Supplying, fixing and wiring 50/5 to 400/5Amps 5VA burden Current Transformer. Class 0.5 accuracy with Tape Wound. Page 19 Item No: 5.34 Vol-6 of Ele SR - 2023-24

Supplying, fixing of LED type panel board indicating lamp with required colour suitable for 220VA.C 50HZ 12/24V DC. Page 19 Item No: 5.38 Vol-6 of Ele SR - 2023-24

Supplying 400 amps rated 3phase with neutral bus bar using required capacity electrolytic aluminium strips covered with heat shrinkable coloured PVC sleeve, mounted on henolic/FRP/DMC insulator which ...

Supplying and fixing Moulded Case Circuit Breaker (MCCB) over the existing wood/panel board using necessary screws, bolts, nuts, necessary phase separators, handle and wiring complete. Protection of O...

Supplying and fixing Moulded Case Circuit Breaker (MCCB) over the existing wood/panel board using necessary screws, bolts, nuts, necessary phase separators, handle and wiring complete. Protection of O...

Supplying and fixing miniature circuit breakers on existing MCB distribution boards using necessary fixing materials and C Type curve, indicator ON/OFF, energy cross-3 with Short circuit breaking capa...

Supplying ,fixing and wiring heavy duty low voltage capacitors conforming to IS 2834. 3 phase, 400/440 volts grade, for power factor improvement of rotating machineries like induction motor.. Cost per...

Supplying ,fixing and wiring heavy duty low voltage capacitors conforming to IS 2834. 3 phase, 400/440 volts grade, for power factor improvement of rotating machineries like induction motor.. Cost per...

Fabricating supplying and mounting MS box made out... SWG suitable for floor/wall mounting, fully weather proof with provision for better heat dissipation, provided with hinged front cover,equipped wi...

Supplying and fixing hylum plastic sheet 3mm thick with necessary nitches for fixing switches, regulators etc., and fixing on existing wood or metal box using N. F. screws. Page 9 Item No: 3.9 Vol-6 ...

OUTDOOR LIGHTING PANEL :Supply, Installation, Testing and Commissioning of L.T. outdoor panel panels including the cost of pedestals required to fix 40 A mcb 1 no for incoming along with bus bar and ...

OUTDOOR LIGHTING PANEL :Supply, Installation, Testing and Commissioning of L.T. outdoor panel panels including the cost of pedestals required to fix 40 A mcb 1 no for incoming along with bus bar and ...

OUTDOOR LIGHTING PANEL :Supply, Installation, Testing and Commissioning of L.T. outdoor panel panels including the cost of pedestals required to fix 40 A mcb 1 no for incoming along with bus bar and ...

OUTDOOR LIGHTING PANEL :Supply, Installation, Testing and Commissioning of L.T. outdoor panel panels including the cost of pedestals required to fix 40 A mcb 1 no for incoming along with bus bar and ...

OUTDOOR LIGHTING PANEL :Supply, Installation, Testing and Commissioning of L.T. outdoor panel panels including the cost of pedestals required to fix 40 A mcb 1 no for incoming along with bus bar and ...

OUTDOOR LIGHTING PANEL :Supply, Installation, Testing and Commissioning of L.T. outdoor panel panels including the cost of pedestals required to fix 40 A mcb 1 no for incoming along with bus bar and ...

OUTDOOR LIGHTING PANEL :Supply, Installation, Testing and Commissioning of L.T. outdoor panel panels including the cost of pedestals required to fix 40 A mcb 1 no for incoming along with bus bar and ...

OUTDOOR LIGHTING PANEL :Supply, Installation, Testing and Commissioning of L.T. outdoor panel panels including the cost of pedestals required to fix 40 A mcb 1 no for incoming along with bus bar and ...

OUTDOOR LIGHTING PANEL :Supply, Installation, Testing and Commissioning of L.T. outdoor panel panels including the cost of pedestals required to fix 40 A mcb 1 no for incoming along with bus bar and ...

OUTDOOR LIGHTING PANEL :Supply, Installation, Testing and Commissioning of L.T. outdoor panel panels including the cost of pedestals required to fix 40 A mcb 1 no for incoming along with bus bar and ...

OUTDOOR LIGHTING PANEL :Supply, Installation, Testing and Commissioning of L.T. outdoor panel panels including the cost of pedestals required to fix 40 A mcb 1 no for incoming along with bus bar and ...

Supplying of -1.1 kV, XLPE or Heat resistant PVC insulated, PVC exutruted Inner Seath

Armoured LTUG Cable as per IS-1554 (Part 1) or IS-7098 Part-1, Armouring strip thickness and resistivity as per ...

Supplying of -1.1 kV, XLPE or Heat resistant PVC insulated, PVC exutruted Inner Seath Armoured LTUG Cable as per IS-1554 (Part 1) or IS-7098 Part, Armouring strip thickness and resistivity as per IS-...

Supplying of 1.1 kV, XLPE or Heat resistant PVC insulated, PVC exutruted Inner Seath

Armoured LTUG Cable as per IS-1554 (Part 1) or I--7098 Part-1, Armouring strip thickness and resistivity as per I...

Supplying of 1.1 KV, XLPE or Heat resistant PVC insulated, PVC exutruted Inner Seath Armoured LTUG Cable as per IS 1554 (Part1) or IS-7098 Part-1 Armouring strip thickness and resistivity as per IS ...

Supplying of 1.1 kV, XLPE or Heat resistant PVC insulated, PVC exutruted Inner Seath

Armoured LTUG Cable as per IS-1554 (Part 1) or IS-7098 Part-1, Armouring strip thickness and resistivity as per ...

Supplying tinned copper lugs and crimping and wiring to terminal point for wire of the following sizes Heavy Duty Copper Terminal Long Barrel 120 Sqmm Copper Terminal, Apprx Wt: 64 Gm 0

Supplying tinned copper lugs and crimping and wiring to terminal point for wire of the following sizes Heavy Duty Copper Terminal Long Barrel 240 Sqmm Copper Terminal, Apprx Wt: 218 Gm Supplying tinne...

Brass Cable Gland for 10 to 16 mm cable -25 Sqmm P. No. 28 of 81, Sl. No.507, I. No. 63.01, Vol-6, Part-III of ESCOMs SR 2023-24

Brass Cable Gland for 35 Sqmm cable - 32 sqmm P. No. 28 of 81, Sl. No.507, I. No. 63.02, Vol-6, Part-III of ESCOMs SR 2023-24

Supplying & Laying cable trays including welding, fixing of supports - Cable tray of 600 mm width (suitable for cable ducts of A, B & C type) 600x50mm Page 120 Item No: 22.(a).i Vol-6 Of Ele SR - 2...

Providing chain link fencing 50 mm size of 8 guage properly stretched between rectangular Poles and fixed with suitable bolts & nuts, the free ends shall be welded to the Pole and block pipe at top an...

Jelly Spreading (20-25 mm) : Supplying and providing jelly in the station yard of uniform thickness of 100 mm including the cost of materials, labour charges, required tools and plants etc., complet...

Supplying and fixing regular MCB distribution boards on wall/woodboard/flush mounting using required clamps ,bolts,nuts,etc with provision for fixing suitable type capacity MCBs single phase/3phase ...

Supplying and fixing regular MCB distribution boards on wall/woodboard/flush mounting using required clamps ,bolts,nuts,etc with provision for fixing suitable type capacity MCBs single phase/3phase ...

Supplying and fixing miniature circuit breakers on existingMCB distribution boards using necessary fixing materials and C Type curve, indicator ON/OFF, energy cross-3 withShort circuit breaking capaci...

Supplying and fixing miniature circuit breakers on existingMCB distribution boards using necessary fixing materials and C Type curve, indicator ON/OFF, energy cross-3 withShort circuit breaking capaci...

Supplying and fixing miniature circuit breakers on existingMCB distribution boards using necessary fixing materials and C Type curve, indicator ON/OFF, energy cross-3 withShort circuit breaking capaci...

Wiring for lighting/power circuit using one of FRLS PVC insulated 1100V grade, multistrand copper wire with low conductor resistance single core in open or concealed system of wiring with specified IS...

Wiring for lighting/power circuit using one of FRLS PVC insulated 1100V grade, multistrand copper wire with low conductor resistance single core in open or concealed system of wiring with specified IS...

Wiring for lighting/power circuit using one of FRLS PVC insulated 1100V grade, multistrand copper wire with low conductor resistance single core in open or concealed system of wiring with specified IS...

Wiring for lighting/power circuit using one of FRLS PVC insulated 1100V grade, multistrand copper wire with low conductor resistance single core in open or concealed system of wiring with specified IS...

Supplying heavy gauge PVC conduit pipe…. Dia 2mm2.0mm thick comirming to IS 2509 with suitable size bends, metal/PVC junction boxes, adhesive paste etc., and running before Concreting in the slab. ...

Supplying heavy gauge PVC conduit pipe…. Dia 2mm2.0mm thick comirming to IS 2509 with suitable size bends, metal/PVC junction boxes, adhesive paste etc., and running before Concreting in the slab. ...

Supplying heavy gauge PVC conduit pipe…. Dia 2mm, 2.5mm thick with suitable size bends, metal junction boxes, adhesive paste etc., by groove cutting in the wall & fixing by bracing U or J hooks & ce...

Supplying heavy gauge PVC conduit pipe…. Dia 2mm, 2.5mm thick with suitable size bends, metal junction boxes, adhesive paste etc., by groove cutting in the wall & fixing by bracing U or J hooks & ce...

Supplying heavy gauge PVC conduit pipe…. Dia 2mm, 2.5mm thick with suitable size bends, metal junction boxes, adhesive paste etc., by groove cutting in the wall & fixing by bracing U or J hooks & ce...

Supplying and wiring adopting loop system in existing PVC Conduit /casing capping using 2x1.5mm2(Phase & Neutral)& 1x1.0 mm2 (Earth wire) FRLS multi strand PVC insulatedcopper wire ( confirming to IS-...

Supplying and wiring adopting loop system in existing PVC Conduit /casing capping using 2x1.5mm2(Phase & Neutral)& 1x1.0 mm2 (Earth wire) FRLS multi strand PVC insulatedcopper wire ( confirming to IS-...

Supplying and wiring adopting loop system in existing PVC Conduit /casing capping using 2x1.5mm2(Phase & Neutral)& 1x1.0 mm2 (Earth wire) FRLS multi strand PVC insulatedcopper wire ( confirming to IS-...

Supplying and wiring adopting loop system in existing PVC Conduit /casing capping using 2x1.5mm2(Phase & Neutral)& 1x1.0 mm2 (Earth wire) FRLS multi strand PVC insulatedcopper wire ( confirming to IS-...

Supplying and flush mounting powder coated / galvanized metal box suitable for mounting modular switch plates. The box should be firmly flush mounted after due groove cutting in Brick/Stone/C.Cwall: 1...

Supplying and flush mounting powder coated / galvanized metal box suitable for mounting modular switch plates. The box should be firmly flush mounted after due groove cutting in Brick/Stone/C.Cwall: 4...

Supplying and flush mounting powder coated / galvanized metal box suitable for mounting modular switch plates. The box should be firmly flush mounted after due groove cutting in Brick/Stone/C.Cwall: 6...

Supplying and flush mounting powder coated / galvanized metal box suitable for mounting modular switch plates. The box should be firmly flush mounted after due groove cutting in Brick/Stone/C.Cwall: 8...

Supplying and flush mounting powder coated / galvanized metal box suitable for mounting modular switch plates. The box should be firmly flush mounted after due groove cutting in Brick/Stone/C.Cwall: 1...

Supplying and fixing PVC/Metal conduit deep juction box 32mm Deep junction box 10-12 way

Supplying and fixing Metal fan box with round hook Supplying and fixing PVC/Metal conduit deep juction box

Supplying and fixing superior quality modular switch mounting polycarbonate plate with necessary supporting back plate with required nos. of machine screws, bolts nuts etc., complete on the existing m...

Supplying and fixing superior quality modular switch mounting polycarbonate plate with necessary supporting back plate with required nos. of machine screws, bolts nuts etc., complete on the existing m...

Supplying and fixing superior quality modular switch mounting polycarbonate plate with necessary supporting back plate with required nos. of machine screws, bolts nuts etc., complete on the existing m...

Supplying and fixing superior quality modular switch mounting polycarbonate plate with necessary supporting back plate with required nos. of machine screws, bolts nuts etc., complete on the existing m...

Supplying and fixing superior quality modular switch mounting polycarbonate plate with necessary supporting back plate with required nos. of machine screws, bolts nuts etc., complete on the existing m...

Supplying and fixing of modular switch/socket/stepped electronic fan regulator/dimmer/telephone socket etc on existing modular switch plate as per IS 3854 and IS 1293: 6A One Way Switch I.No.3.6.1, P....

Supplying and fixing of modular switch/socket/stepped electronic fan regulator/dimmer/telephone socket etc on existing modular switch plate as per IS 3854 and IS 1293: 6A Two Way Switch I.No.3.6.2, P....

Supplying and fixing of modular switch/socket/stepped electronic fan regulator/dimmer/telephone socket etc on existing modular switch plate as per IS 3854 and IS 1293: 6A Three Way socket I.No.3.6.3, ...

Supplying and fixing of modular switch/socket/stepped electronic fan regulator/dimmer/telephone socket etc on existing modular switch plate as per IS 3854 and IS 1293: Stepped Fan Regulator Two Module...

Supplying and fixing of modular switch/socket/stepped electronic fan regulator/dimmer/telephone socket etc on existing modular switch plate as per IS 3854 and IS 1293: 16A One Way Switch I.No.3.6.7, P...

Supplying and fixing of modular switch/socket/stepped electronic fan regulator/dimmer/telephone socket etc on existing modular switch plate as per IS 3854 and IS 1293: 6/16A Universal Socket I.No.3.6....

Supplying of .....feet -PVC Batten with integrated LED tube .... W with high quality diffuser with Life of 25000 burning hours & 70% lumen maintenance with CRI Greaterthan 80. Power Input: 220-240V@ 5...

Supplying of .....feet -PVC Batten with integrated LED tube .... W with high quality diffuser with Life of 25000 burning hours & 70% lumen maintenance with CRI Greaterthan 80. Power Input: 220-240V@ 5...

Supply of round/square recess/surface mounted rolling type LED Down light with ...... W GU 10 LED Lamp Rib Fabricated from diecast aluminium with white powder coated prewired to mains connector & has ...

Supply of LED Streetlight with pressure die cast aluminium housing body with optimal heat sink for better thermal dissipation. Diffuser with injection moulded & is made of polycarbonate material with ...

Fabricating , Supplying and erection of 7.0 mts Long Hot dip Galvanised Octogonal pole with BSEN 10025 grade S 355JO steel plate for shaft, IS 2062, for base plate, with door opening arrangments , inc...

Supplying & fixingof Hot dip galvanized MS bracket suitable for out door Luminaries and mounted on Octoganal pole using necessary bolts, nuts etc., Complete. Single arm Bracket with 1500 mm standard ...

Supplying capacitor type 48 sweep ceiling fan complete with down rod blades, shackle, canopies etc., for operation on 230 volts, 50 cycles. single phase AC supply confirminf to ISS-374-1979 and with d...

Supplying exhaust fan of 1440 RPM of 300mm (12) size with bracket blades complete for light duty suitable to operate on 230V 50Hz, AC supply, Supplying capacitor type 48 sweep ceiling fan complete w...

Supplying of 1440rpm heavy duty exhaust fan with bracket blades suitable to operate on 230V 50Hz, AC Supply complete. 15 Sweep(450 mm) Supplying exhaust fan of 1440 RPM of 300mm (12) size with bracket...

Supplying fixing and wiring earth electrode for grounding of lift, transformers, DG sets etc. using 40mm dia 2.9mm thick 2.5 m long GI pipe with GI funnel with mesh and suitable size reducer fixed on...

Supplying & Fixing Chemical earthling for grounding. Conduits, IC cutouts & other equipments backfill compound which is non-corrosive, thermally conductive, potential to permissible limits, superior F...

Supplying and running of GI / Copper strips for grounding connections using necessary fixing materials as required 25X3mm Copper strip Page 55 Item No: 12.60.3 Vol-6 Of SR - 2023-24

Supplying and running of GI / Copper strips for grounding connections using necessary fixing materials as required 25x6mm GI strip Supplying and running of GI / Copper strips for grounding connection...

Supplying and running of GI / Copper strips for grounding connections using necessary fixing materials as required 600X600X3mm Copper Plate 0

Supplying and running of GI / Copper strips for grounding connections using necessary fixing materials as required 25X3mm GI strip 0

Supply and installation of 2kg Fire Extinguisher Mono Ammonium Phosphate Powder 50, Stored Pressure Type, Pressure Gauge, Gross Weight 3.6 Kg, empty weight 1.6 Kg, Can Height 344MM, Diameter 108MM, Di...

Providing ABC powder based MAP 50, Cap: 6kg Supply and installation in position, testing and commissioning 6kg Fire Ex tinguisher Mono Ammonium Phos phate Powd...

Supply and installation of 9 Ltr Fire Extinugisher Aqueous Film Forming Foam Type, Stored Pressure Type, Pressure Gauge, Gross Weight 15.10kg. empty weight 6.10kg Can Height 615 MM, Diameter 175 MM, D...

Supply and installation of 4.5Kg C02 Gas Type aluminium body Squeeze grip Fire Extinugisher, Trolley Mounted, Easy Weight Management, Used Unused Mechanism, Squeeze Grip, Gross Weight 11.16Kg. empty W...

Providing 6 Kg -Supply, installation in position, testing and commissioning of CQRS 6 Kg - Direct Low Pressue System - Gross Weight 9.42 Kg, Empty Weight 3.42 Kg, Can Height 460 MM, Diameter 160M M, ...

Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually co...

Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. ...

Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively with automatic flushing cistern with standard ...

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the w...

Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings. Providing and fixing wash basin with C.I. brackets, 15 mm C.P...

Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings. Providing and fixing white vitreous china pedestal for wash b...

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour 600 mm long towel rail with t...

Providing and fixing PVC (S.W.R) Nahani Trap 10cms x 10cms with all fitting arrangements & all necessary accessories complete 1. 10.0 cms x 10.0 cms P.No.137, I.No.14.40.2 of KPWD S.R2023-24

Providing and fixing in position brass bib cock of approved quality 20 mm nominal bore 1. 10.0 cms x 10.0 cms

Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet - 150mm diameter P.No.117, I.No.13.2.2 of KPWD S.R 2023-24

Providing and fixing brass stop cock of approved quality : 20 mm nominal bore P.No.118, I.No.13.9.2 of KPWD S.R 2023-24

Providing and fixing in un plasticised PVC Connection pipe with brass union 15 mm nominal bore 450 mm length of PVC connection. P.No.117, I.No.13.3.2 of KPWD S.R 2023-24

Providing and fixing gun metal non- return valve of approved quality (screwed end) : 25 mm nominal bore Horizontal P.No.118, I.No.13.8.2.2 of KPWD S.R 2023-24

Providing PVC ringtite pipes conforming to IS 4985:2000 with latest amendments and conveying to worksite, rolling and lowering into trenches, laying true to line and level and perfect linking at joint...

Providing PVC ringtite pipes conforming to IS 4985:2000 with latest amendments and conveying to worksite, rolling and lowering into trenches, laying true to line and level and perfect linking at joint...

Providing PVC ringtite pipes conforming to IS 4985:2000 with latest amendments and conveying to worksite, rolling and lowering into trenches, laying true to line and level and perfect linking at joint...

Providing PVC ringtite pipes conforming to IS 4985:2000 with latest amendments and conveying to worksite, rolling and lowering into trenches, laying true to line and level and perfect linking at joint...

Providing and fixing PTMT grating of approved quality and colour. Circular type 100 mm nominal dia P.No.120, I.No.13.22.1.1 of KPWD S.R 2023-24

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with cla...

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with cla...

Providing and fixing gun metal gate valve with C.I wheel of approved quality (screwed end): of 20mm dia P.No.282, I.No.18.17- 18.17.3 of DSR 2023-24

Providing and fixing gun metal gate valve with C.I wheel of approved quality (screwed end): of 25mm dia P.No.282, I.No.18.17- 18.17.3 of DSR 2023-24

Providing and fixing gun metal gate valve with C.I wheel of approved quality (screwed end): of 40mm dia P.No.282, I.No.18.17- 18.17.3 of DSR 2023-24

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and ...

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipe...

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipe...

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipe...

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipe...

Providing and installing at site of work P.V.C. pipes including cost of pipes and specials and labour, including lowering into trenches, laying true to line, level and perfect linking at joints leak p...

Providing and installing at site of work P.V.C. pipes including cost of pipes and specials and labour, including lowering into trenches, laying true to line, level and perfect linking at joints leak p...

Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber 150 x 100 mm size P type With Non Modular common burnt clay bricks of designation 3.5 & wi...

Constructing brick masonry chamber for underground C.I. inspection chamber and bends with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) C.I. cover with frame (light duty) 600X850 mm internal ...

Constructing brick masonry chamber for underground C.I. inspection chamber and bends with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) C.I. cover with frame (light duty) 455x610 mm internal ...

Extra for depth beyond 45 cm of brick masonry chamber : For 455x610 mm size With common burnt clay (non modular) bricks of class designation 3.5 P.No.127, I.No.13.55.1 of KPWD S.R 2023-24

Waste Water Treatment by Prefabricated anaerobic Bio Septic tank : (For 100 Souls /10KLD)

Providing, installation and commissioning of an anaerobic Bio Septic tank with all necessary accessories such ...

Manufactured Sand Sl. No. 64, Pg No. A-40, Vol-1 K.P.W.D S.R. 2023-24

Providing weep holes in Brick masonry/Plain/ Reinforced concrete abutment, wing wall/ return wall with 100 mm dia AC pipe, extending through the full width of the structure with slope of 1V :20H towar...

Providing PVC ringtite pipes conforming to IS 4985:2000 with latest amendments and conveying to worksite, rolling and lowering into trenches, laying true to line and level and perfect linking at joint...

Construction of Granular Sub-Base of required grading as per design spreading in uniform layers with motor grader on prepared surface mixing by mix in place method with front end loader at OMC and com...

Providing and laying 60mm thick factory made cement concrete paver block of approved shape and colour of M -30 grade made of C&D waste by block making machine with vibratory compaction laid in require...

Supplying and fixing M15 grade precast cement concrete Kerb stones for Roadway, Sidewalls and gutters fixed with CM 1:3 fixed and finsihed in line as per direction of Engineer in charge. (The cost of ...

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade :Two coats on new work after thoroughly brooming the surface to remove all dirt, dust, mortar drops and for...

Providing and laying in position Cement Concrete for all Sub structures of building, Irrigation works, Sub structure works of bridges, Drain works & other parallel works from 0.50m to 3.50 m height. T...

Providing and laying in position Cement Concrete for all Sub structures of building, Irrigation works, Sub structure works of bridges, Drain works & other parallel works from 0.50m to 3.50 m height. T...

Providing and Applying two component, water-based food grade epoxy resin coating on inside surface of Potable water tank having anti-algae, antifungal, Non-toxic, hygiene cum damp-proof coating Certif...

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipe...

Providing & fixing 455x610 mm cast iron cover with frame weight to be not less 38kgs (weight of cover 23 kgs and weight of frame 15 kgs)and necessary locking arrangements with M.S flats 32x6 mm etc & ...

Supply, installing,testing and commissioning COMMON control panel consisting of the following INCOMING:1 No set of Phase indicating lamps with SFU of suitable rating 1 No, Analog Ammeter, 1 No Analo...

Providing, Single Phase Submersible Pump Sets of 100mm dia (4 inch) suitable for bore well confirming to IS 8034-2000 specifications, to work site with testing of as per instructions of engineer incha...

Supply and delivery at site Brand new best make PVC insulated cable of Flat 3 core (sheathed) of nominal cross sectional area as per IS 694-1990 with ISI Mark and as per its latest amendments -1x3x6...

Supplying, filling, spreading & leveling stone boulders of size range 5 cm to 20 cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of Engineer-in-ch...

Supplying, filling, spreading &leveling gravels of size range 5 mm to 10 mm, in the recharge pit, over the existing layer of boulders, in required thickness, for all leads & lifts, all complete as per...

Supplying, filling, spreading &leveling coarse sand of size range 1.5 mm to 2 mm in recharge pit, in required thickness over gravel layer, for all leads & lifts, all complete as per direction of Engi...

Providing and laying 100mm thick pre-cast cover slabs over drains & Rain pit of width not exceeding 800 mm using M20 concrete reinforced with Micro Alloyed High carbon steel with 3mm - 3ply wired stee...

Geophysical Investigation of site for sinking Borewell Geophysical Investigation of site for sinking Borewell for supplying drinking water to the habitation either through a hand pump, Mini Water Supp...

Sinking of Borewell of 165mm dia clear using super fast hydraulic rig of capacity 300 PSIG & above 1100 CMF & above in all strata including over burdern. Fixing of casing pipes, collars and cap with n...

Sinking of Borewell of 165mm dia clear using super fast hydraulic rig of capacity 300 PSIG & above 1100 CMF & above in all strata including over burdern. Fixing of casing pipes, collars and cap with n...

Sinking of Borewell of 165mm dia clear using super fast hydraulic rig of capacity 300 PSIG & above 1100 CMF & above in all strata including over burdern. Fixing of casing pipes, collars and cap with n...

Sinking of Borewell of 165mm dia clear using super fast hydraulic rig of capacity 300 PSIG & above 1100 CMF & above in all strata including over burdern. Fixing of casing pipes, collars and cap with n...

Sinking of Borewell of 165mm dia clear using super fast hydraulic rig of capacity 300 PSIG & above 1100 CMF & above in all strata including over burdern. Fixing of casing pipes, collars and cap with n...

Sinking of Borewell of 165mm dia clear using super fast hydraulic rig of capacity 300 PSIG & above 1100 CMF & above in all strata including over burdern. Fixing of casing pipes, collars and cap with n...

Supply of ISI mark 175mm nominal bore,plain and steel casing pipe grade of steel Fe 410 of wall thickness conforming to IS 4270-2001 and latest ammendments, electrical resistance welded steel tubes,...

Providing and laying at site of work MS casing caps as per IS 1239 (part 2 1982 with al latestamendments if any for any dia. The thickness of plate used for covering one end shall be 3mm (minimum) The...

Providing and fixing MS casing collars as per IS 1239 (part-II) 1982 with all latest amendments if any for any dia. The thickness of plate used for covering one end shall be 3mm (minimum). The dimensi...

Supply and Errection of submersible PUMPSET suitable for borewell of 150mm dai and haing declared duty conditions as detailed below nd satisfying performance characteristic for pump and motar as decla...

Supply and delivery of galvanized mild steel tubes of 6mtr standard length heavy duty (C Class) as per IS 1239 (Part-I) 1990 with latest amendments with ISI Mark (one end fitted with Heavy Duty colla...

Labour charges for Erection of new / repaired submersible pump set along with GI pipes (32mm / 50mm), cable (New submersible pump set if required will be supplied by the department free of cost and ...

Providing and fixing in position 50mm Nominal bore non- return valve vertical type of approved make including cost of all materials, labour and HOM of equipment with all leads compleate as per specifi...

Supply, installing,testing and commissioning COMMON control panel consisting of the following INCOMING:1 No set of Phase indicating lamps with SFU of suitable rating 1 No, Analog Ammeter, 1 No Analo...

1.1 kV, XLPE or Heat resistant PVC insulated, PVC exutruted Inner Seath Armoured LTUG Cable as per IS-1554 (Part 1) or IS-7098 Part-1, Armouring strip thickness and resistivity as per IS-3975 16 Sqm...

Labour charges for laying of 1.1 KV class UG cable in existing trench GI pipe / stoneware pipe / on wall / on pole as required. In existing trench/duct / 6 sqmm to 16 sqmm PWD Electrical SR(2023-24), ...

Earth work excavation for pipeline trenches in all kinds of soils by mechanical means above 600 mm trench width as per drawing and technical specifications, including setting out, construction of shor...

Supplying and fixing of class A (medium duty) GI pipe of wall thickness not less than 3.25mm on pole/wall/drain crossing with necessary clamping arrangements for UG cable of 1.1 KV. 65mm PWD Electrica...

Supplying and fixing L.T. cast Iron pot heads suitable for 1.1 KV class UG cable filled with necessary bitumen/insulating compound complete with terminals, clamps, bolts, nuts and washers etc. 16Sqmm ...

Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material to the appropriate disposal area as per direction of Engineer-in-charge. P...

Demolishing cement concrete manually/ by mechanical means including disposal of material to the appropriate disposal area as per direction of Engineer-in-charge. P.No.187, I.No.19.2.1, Vol-2 of KPWD S...

Providing and laying in position Cement Concrete for all Sub structures of building, Irrigation works, Sub structure works of bridges, Drain works & other parallel works from 0.50m to 3.50 m height. T...

Providing and removing centering, shuttering, strutting, propping etc., and removal of form work for foundations, Foundation, Sub structure of cross drainages P.No.111, I.No. 3 Addendum-1 of Vol-1, KP...

Providing and removing centering, shuttering, strutting, propping etc., and removal of form work for foundations, Foundation, Sub structure of cross drainages P.No.112, I.No. 11 Addendum-1 of Vol-1, K...

Providing and removing centering, shuttering, strutting, propping etc., and removal of form work for Slab P.No.112, I.No. 15 Addendum-1 of Vol-1, KPWD S.R 2023-24

Refilling available earth around trenches/pipelines, cables in layers not exceeding 20 cms in depth, compacting each deposited layer by ramming after watering with a lead upto 50 m , and lift upto 1.5...

Supply of Fabricated main frame for housing refractory bricks and other equipment, Furnace the main door, furnace supporting frame, Main door lifting mechanism by hydraulic system, Hand pump is provid...

Supply, Installation, Testing, & Commissioning of refractory items such as ceramic fiber blankets, insulation bricks, Hot Zone bricks (IS8), Cold Zone bricks (lS6), body resting bricks, arch-supportin...

Supply, Installation, Testing, & Commissioning of vertical Heating coil

Power of 42 KW. Heating coils are made out of 8 swg Kanthal APM wire / Nichrome 80/20 wire of 8 Gauge with terminal rods. Ver...

Supply, Installation, Testing, & Commissioning of Body Charging Trolley Supply of fabricated Hydraulically operated Body Charging Trolley with power pack and connecting pipelines and control desk to ...

Supply, Installation, Testing, & Commissioning of Electric Remote Control panel. The control panel is built with the following components housed in Panel made out of M S sheet duly powder coated, wit...

Supply, Laying, Testing, & Commissioning of Control & Power Cables Supply of power cables, bus bar laying, supporting tray, conduit pipes, from the control panel to various equipments, heating coils, ...

Supply, Installation, Testing, & Commissioning of Water pumpnSupply of water pump for scrubber unit. 1 Hp motor, 3 Phase, 415V, for circulating the water in wet venture scrubber unit and necessary pip...

Supply, Installation, Testing, & Commissioning of Fresh air blower Made out of M S Sheet, direct driven motor of 1 Hp, 3 Phase, 415V, of suitable capacities, mounted on a M S rigid angle frame, connec...

Supply, Installation, Testing, & Commissioning of Scrubber unit Wet scrubber unit with venturi arrangements made out of S S 304G sheets. In unit-1 smoke will completely come in contact with water and ...

Supply, Installation, Testing, & Commissioning of online-Exhaust Blower Fabricated with an S S 304G sheet, the impeller driving shaft is also made out of S S with bearing support mounted on a suitable...

Erection charges for Erection, testing, commissioning, handing over the cremation furnace (a) Fixing of Frame, Main Door, Counterweight, Mechanical and Electrical operating door system. (b) Refractory...

Packing, forwarding, Loading, and Unloading charges from our factory in Bangalore to the crematorium site.

Supply, Installation, Testing, & Commissioning of Self-supporting chimney. The chimney is made out of M S Plates, angles, flats, grouting bolts & gusset plates, ladder, platform with a protection cage...

Construction of Electric Crematorium at KGF CMC under UIDF scheme

Earth work excavation for Foundation by mechanical means for all works & depth upto 3 m, as per drawing and technical specifications, including setting out, shoring, strutting, barricading, caution li...

Earth work in surface excavation by mechanical means for lowering & leveling the ground for all works other than foundation in all kinds of soils & upto depth not exceeding 300mm as per drawing and te...

Earth work excavation for Foundation by Mechanical means depth upto 1.50m, as per drawing and technical specifications, including setting out, shoring,strutting, barricading, caution lights, including...

Earth work excavation for Foundation by mechanical means for all works & depth upto 3 m, as per drawing and technical specifications, including setting out, shoring, strutting, barricading, caution li...

Providing and injecting chemical emulsion for Pre-constructional Anti-Termite Treatment, creating continuous chemical barrier under and around the column pits, walls, trenches, basement excavation, to...

Providing and laying in position plain cement concrete for levelling course for all works in foundation. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS...

Providing and laying in position Reinforced cement concrete for all Foundation works. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixe...

Providing and laying in Reinforced cement concrete for all Basement & surface level works, return walls, retaining walls, sunken floors etc. The granite/trap/basalt crushed graded coarse aggregates an...

Providing and laying in position Reinforced cement concrete for all Super structures of building , Road works, Water works, Irrigation works & super structure works of bridges upto 3.50 m height. The ...

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations and other similar works etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by r...

Refilling available earth around trenches/pipelines, cables in layers not exceeding 20 cms in depth, compacting each deposited layer by ramming after watering with a lead upto 50 m , and lift upto 1.5...

Providing and laying in position Cement Concrete for all Foundation works. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed with supe...

Providing and laying in Cement Concrete for all Basement & surface level works, return walls, retaining walls, sunken floors etc. The granite/trap/ basalt crushed graded coarse aggregates and fine agg...

Providing and laying in position Cement Concrete for all Sub structures of building, Irrigation works, Sub structure works of bridges, Drain works & other parallel works from 0.50m to 3.50 m height. T...

Providing and laying in position Cement Concrete for all Sub structures of building, Irrigation works, Sub structure works of bridges, Drain works & other parallel works from 0.50m to 3.50 m height. T...

Providing and laying in position Cement Concrete for all Super structures of building , Road works, Water works, Irrigation works & super structure works of bridges upto 3.50 m height. The granite/tra...

Providing and laying in position Cement Concrete for all Super structures of building , Road works, Water works, Irrigation works & super structure works of bridges upto 3.50 m height. The granite/tra...

Providing and laying in position Cement Concrete for all Super structures of building , Road works, Water works, Irrigation works & super structure works of bridges upto 3.50 m height. The granite/tra...

Providing and laying in position Cement Concrete for all Super structures of building , Road works, Water works, Irrigation works & super structure works of bridges upto 3.50 m height. The granite/tra...

Providing and laying in position Cement Concrete for all Super structures of building , Road works, Water works, Irrigation works & super structure works of bridges upto 3.50 m height. The granite/tra...

Providing and laying in position Cement Concrete for all Foundation works. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed with supe...

Supplying, fitting and placing TMT FE 550 / 550D Steel Reinforcement including cost of all materials, machinery, labour, cleaning, straightening, cutting, bending, hooking, laping/welding joints, ty...

Supplying, fitting and placing TMT FE 550 / 550D Steel Reinforcement including cost of all materials, machinery, labour, cleaning, straightening, cutting, bending, hooking, laping/welding joints, ty...

Providing Size Stone masonry with hard stone in foundation & plinth with Cement mortar 1:6 (1 cement : 6 coarse sand)

Providing ruled pointing to coursed stone masonry with lime mortar 1:3, 20mm deep, after raking joints to depth of 20mm nicely lining, including cost all materials, labour, usage charges of machinery,...

Providing and constructing load bearing wall with concrete solid blocks having block ebsity not less than 1800 kg/m3 Having aq minimum average compressive strength of 5.00 N.mm2 confirming to IA 2185 ...

Providing and constructing load bearing wall with Solid Concrete blocks of size 400x100x200mm having block density more than 1800kg/m3 and minimum compressive strength of 4.00 N/mm2 conforming to IS 2...

Providing 12 mm cement plaster finished with a floating coat of neat cement of mix :1:4 (1 cement: 4 fine sand) to brick masonry including rounding off corners wherever required smooth rendering, prov...

Providing 12 mm cement plaster finished with a floating coat of neat cement of mix :1:4 (1 cement: 4 fine sand) to brick masonry including rounding off corners wherever required smooth rendering, prov...

Providing 15 mm cement plaster on rough side of single or half brick wall finished with a floating coat of neat cement of mix: 1:4 (1 cement: 4 fine sand) to brick masonry including rounding off corne...

Providing 15 mm cement plaster with cement mortar 1:3 (1 cement: 3 coarse sand) finished with a floating coat of neat cement on the rough side of single or half brick wall including rounding off corne...

Providing 20 mm cement plaster with cement mortar 1:3 (1 cement: 3 coarse sand) finished with a floating coat of neat cement to brick/stone masonry including rounding off corners wherever required smo...

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete as per sp...

Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre of approved brand and manufacture, including applying add...

Finishing walls with Acrylic Smooth exterior paint of required shade :New work (Two coat applied @ 1.67 ltr/10 m² over and including priming coat of exterior primer applied @ 2.20 kg/10 m²) with pai...

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitt...

Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on spec...

Finishing with Epoxy paint (two coats) at all locations prepared and applied as per manufacturer's specifications including appropriate priming coat, preparation of surface, etc. complete. On steel wo...

Providing and fixing ball bearing for rolling shutters including cost of materials, labour, usage charges of machinery complete as per specifications and as per directions of the Engineer-in-Charge.

Extra for providing Manually operated Bevel Gear Box for operating rolling shutters including cost of materials, labour, usage charges of machinery complete as per specifications and as per directions...

Providing & fixing of 3track x 2-panel sliding windows made out of multi chambered UPVC(Matching to RAL-9016) sections and with minimum TiO2(Titanium Dioxide) at 6PHR with TPV(Thermo Plastic Vulcanize...

Providing & fixing of louvered ventilator made out of multi chambered UPVC(Matching to RAL-9016) sections and with minimum TiO2(Titanium Dioxide) at 6PHR with TPE(Thermo Plastic Elastomer) and lead fr...

Providing and fixing pressed steel door frames conforming to IS: 4351, manufactured from commercial mild steel sheet of 1.60 mm thickness, including hinges, jamb, lock jamb, bead and if required angle...

Providing & fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows, all complete with : 5.5 mm thick glass panes including cost of materials, labour, usage charges...

Providing and fixing Fiber Glass Reinforced plastic (FRP) Door Frames cross- section 90 mm x 45 mm having single rebate of 32 mm x 15 mm to receive shutter of 30 mm thickness. The laminate shall be m...

Providing and fixing to existing door frames Glass Fibre Reinforced Plastic (FRP) panelled door shutter of required colour and approved brand and manufacture, made with fire - retardant grade unsatura...

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or roundbars etc. including priming coat with approved steel primer all complete. Fixed to steel ...

Providing and laying Cement concrete pavement with 1:2:4 for commercial & residential building floors, hardpaths, footpaths using 1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size...

Providing and fixing bright finished brass butt hinges with necessary screws etc. complete :125x85x5.5 mm (heavy type)

Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Bar rel type) with necessary screws etc. complete :

Providing and fixing ISI marked oxidised M.S. handles conforming to IS:4992 with necessary screws etc. complete :125mm

Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 m...

Providing and laying flamed finish Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with...

Providing and fixing 1st quality ceramic glazed floor tiles conforming to IS : 15622 (thickness to be specified by the manufacturer ) of approved make in all colours, shades except burgundy, bottle ...

Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle gre...

Providing and fixing Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approv...

Providing & fixing corrugated G.S. sheet roofing including vertical /curved surface fixed with polymer coated J or L hooks, bolts and nuts 8mm diameter with bitumen and G.I. limpet washers or with G.I...

Providing and laying water proofing treatment to the Roof with PU based single component elastomeric pure polyurethane based coating on New terrace/Chajjas/Sunken portion of WC:Bathroom, cold applied ...

Providing and fixing of wall cladding using 20mm thick gang saw water cut Shiva gold granite, grey granite in CM 1:3 (1 cement : 3 coarse sand) proportion cut to required shape, pattern with paper j...

Providing & fixing 10 mm thick plaster of Paris (gypsum anhydrous) ceiling up to a height of 5 m above floor level, over first class kail wood strips 25x6 mm with 10 mm gap in between and reinforced w...

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and ...

Providing and fixing chorinated poly vinyl Chloride (CPVC) pipes conforming to IS 15778 having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings, thi...

Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 g.

Providing and fixing Brass full way valve gate with C.I. wheel of approved quality (screwed end) :

Providing and fixing in position below given nominal bore gun metal non-return valve horizontal type of approved make including cost of all materials, labour and HOM of equipments specification.

Providing and fixing seating bench Ino base slab, Ino back rest, 2no legs, made up of granite stone with nice finish chamfered edge and fillet corner finishes is conveyed to work site it is inclusive ...

Supplying and fixing M15 grade precast cement concrete Kerb stones for Roadway, Sidewalls and gutters fixed with CM 1:3 fixed and finsihed in line as per direction of Engineer in charge. (The cost of ...

Earth work in surface excavation for stripping, seating of bund, Road way by manual means for lowering & levelling the ground for all works other than foundation & depth in Ordinary rock and soft rock...

Providing and laying in position Cement Concrete for levelling course for all works in foundation. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes...

Wet Mix Macadam (Plant Mix Method)Providing, laying, spreading and compacting graded stone aggregate to wet mix macadam specification including premixing the Material with water at OMC in mechanical m...

Providing and laying 60mm thick factory made precast M -30 grade Cement Concrete Paver Block as per IRC SP 63:2018 & IS 15658 for Cycle Tracks & Pedestrian Footpaths of approved shape and colour, laid...

Providing and fixing of Door locking arrangements(page a-20,item no 274)

Providing and fixing of Handles powder coated 150mm(page A-25,item No,433)

Providing and fixing of Hinges 5" heavy duty(Page No.A-25,item No443)

Providing and fixing of Hold fasts MS (Page No A-25, item No 444)

Providing and fixing of Tower bolt 300mm long(page No,XVI, item No 407)

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually c...

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the w...

Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively with automatic flushing cistern with standard ...

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complet...

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. 600 mm long towel rail with ...

Providing and fixing PTMT angle stop cock 15 mm nominal bore, weighing not less than 85 g

Providing and fixing CP Brass 32mm size Bottle Trap of approved quality & make and as per the direction of Engineer-in-charge.

Providing and fixing PTMT, push cock of approved quality and colour.15 mm nominal bore, 98 mm long, weighing not less than 75 gms

Providing and fixing in position brass stop cock of approved quality of as per dia nominal bore including cost of all materials,labour and HOM of equipments with all leads complete as per specificati...

Providing and fixing in position brass stop cock of approved quality of as per dia nominal bore including cost of all materials,labour and HOM of equipments with all leads complete as per specificati...

Providing and fixing in position brass bib cock of approved quality of as per dia nominal bore including cost of all materials,labour and HOM of equipments with all leads complete as per specificatio...

Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 g.

Providing and fixing granite stone slab with table rubbed, edges rounded and polished, of size 75x50 cm deep and 1.8 cm thick, fixed in urinal partitions by cutting a chase of appropriate width with c...

Providing and fixing bright finished brass hard drawn hooks and eyes :300mm

Providing & fixing Chorinated Poly Venyl(CPVC) pipes confirming to IS 15778 having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings, this includes j...

Providing & fixing Chorinated Poly Venyl(CPVC) pipes confirming to IS 15778 having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings, this includes j...

Providing & fixing Chorinated Poly Venyl(CPVC) pipes confirming to IS 15778 having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings, this includes j...

Providing & fixing Chorinated Poly Venyl(CPVC) pipes confirming to IS 15778 having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings including fixing...

Providing & fixing Chorinated Poly Venyl(CPVC) pipes confirming to IS 15778 having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings including fixing...

Providing & fixing Chorinated Poly Venyl(CPVC) pipes confirming to IS 15778 having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings including fixing...

Providing and fixing water meter with stop cock, jam nut, socket in G.I pipe line including cutting and threading the pipe and making long screws including cost of all materials, labour , HOM of equip...

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete 25 mm Dia

Providing and fixing Brass full way valve gate with C.I. wheel of approved quality (screwed end) 32 mm Dia

Providing and fixing Brass full way valve gate with C.I. wheel of approved quality (screwed end) 40mm.dia..

Providing and fixing in position below given nominal bore gun metal non-return valve horizontal type of approved make including cost of all materials, labour and HOM of equipments specification 40mm.N...

Supplying PVC ringtite pipes conforming to IS 4985:2000 with latest amendments and conveying to worksite, rolling and lowering into trenches, laying true to line and level and perfect linking at joint...

Supplying PVC ringtite pipes conforming to IS 4985:2000 with latest amendments and conveying to worksite, rolling and lowering into trenches, laying true to line and level and perfect linking at joint...

Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors :*100 mm inlet ...

Providing and fixing PTMT grating of approved quality and colour.

Cleaning and desilting of gully trap chamber, including removal of rubbish mixed with earth etc. and disposal of same, all as per the direction of Engineer-in- charge.

Constructing brick masonry chamber of internal dimension 600x450mm and depth of 600mm (inner dimensions) with modular bricks of CD 75 in cement mortar 1:6, bed concrete 150mm thick with 1:3:6, plaster...

Providing and constructing “WIRE CUT BRICK MACHINEHOLE CHAMBERS” using Portland/Pozzolana cement, conical in shape at top, with CC 1:3:6 foundation using 40mm and down size graded metal of approve...

Providing and fixing SFRC frame and cover conforming to IS 12592 (part-I)-1988 and IS 12592 (part-II)- 1991 with latest amendment, including cutting slabs to the required size for the opening and fixi...

Providing 20mm square M.S.Footrest and fixing in manhole with 1:3:6 cement concrete block of 20x20x10 cms using 20mm an ddown size metal of size including cost of materials, labour charges, curing com...

Providing and laying water proofing treatment to the Retaining wall area with PU Elastomeric Single component liquid applied, cold applied, moisture cured high tensile elastomeric PU waterproofing mem...

Geophysical investigation at site for sinking borewells for supplying drinking water to the habitation either through the Hand Pump MWS or P.W.S.S, by vertical electrical sounding by adopting Venner o...

Sinking of Borewell of 165mm dia clear using super fast hydraulic rig of capacity 300 PSIG & above 1100 CMF & above in all strata including over burdern upto 20 m. Fixing of casing pipes, collars and ...

Sinking of Borewell of 165mm dia clear using super fast hydraulic rig of capacity 300 PSIG & above 1100 CMF & above in all strata including over burdern upto 20 m. Fixing of casing pipes, collars and ...

Sinking of Borewell of 165mm dia clear using super fast hydraulic rig of capacity 300 PSIG & above 1100 CMF & above in all strata including over burdern upto 20 m. Fixing of casing pipes, collars and ...

Sinking of Borewell of 165mm dia clear using super fast hydraulic rig of capacity 300 PSIG & above 1100 CMF & above in all strata including over burdern upto 20 m. Fixing of casing pipes, collars and ...

Sinking of Borewell of 165mm dia clear using super fast hydraulic rig of capacity 300 PSIG & above 1100 CMF & above in all strata including over burdern upto 20 m. Fixing of casing pipes, collars and ...

Sinking of Borewell of 165mm dia clear using super fast hydraulic rig of capacity 300 PSIG & above 1100 CMF & above in all strata including over burdern upto 20 m. Fixing of casing pipes, collars and ...

Providing and laying at site of work MS casing caps as per IS 1239 (part- II) 1982 with all latest amendments if any for any dia. The thickness of plate used for covering one end shall be 3mm (minimum...

Providing and fixing MS casing collars as per IS 1239 (part-II) 1982 with all latest amendments if any for any dia. The thickness of plate used for covering one end shall be 3mm (minimum). The dimensi...

Supply of ISI mark 175mm nominal bore,plain and steel casing pipe grade of steel Fe 410 of wall thickness conforming to IS 4270-2001 and latest ammendments, electrical resistance welded steel tubes, m...

Supply and delivery at site Brand new best make PVC insulated cable of Flat 3 core (sheathed) of nominal cross sectional area as per IS 694-1990 with ISI Mark and as per its latest amendments. (PWD C...

Providing,supplying to work site, Submersible Pump Set of 150mm dia suitable for bore well and confirming to IS 8034-2000;3Phase, SS Bowl & Impeller with Low volt Motor as per specifications,as per ne...

Supply and delivery at site of brand new best make gate valve as per IS 778/1984 with ISI Mark and as per its latest amendments SIZE 50 MM

Supply and delivery at site of brand new best make non-return valve as per IS 778/1984 with ISI Mark and as per its latest amendments

Supply, installing,testing and commissioning COMMON control panel consisting of the following INCOMING:1 No set of Phase indicating lamps with SFU of suitable rating 1 No, Analog Ammeter, 1 No Analog ...

Labour charges for Erection, Electrification and commissioning of Pump sets, including aligning and balancing of all items including supply and erection of two pair of supporting clamps, bore well cap...

Labour charges for erection of indoor type panel board and meter board units with all necessary materials and labour tools and equipments including cement concrete for foundation/bed etc,complete as p...

Supplying & fixing miniature circuit breakers on existing MCB distribution boards using necessary fixing materials and 'C' Type curve, indicator ON/OFF, energy cross-3 with Short circuit breaking capa...

Supplying and wiring adopting loop system in existing PVC Conduit /casing capping casing capping using 2x1.5mm2 (Phase & Neutral) & 1x1.0 mm2 (Earth wire) FRLS multi strand PVC insulated copper wire (...

Earth work in surface excavation by mechanical means for lowering & leveling the ground for all works other than foundation in all kinds of soils & upto depth not exceeding 300mm as per drawing and te...

Granular Sub Base (By Mix in Place Method) Construction of Granular Sub-Base of required grading as per design spreading in uniform layers with motor grader on prepared surface mixing by mix in place ...

Providing and constructing un-reinforced plain cement concrete pavement, thickness as per design, over a prepared sub base, with 43 grade cement or any other type as per Clause 1501.2.2 M30 (Grade), c...

Open Conduit System Supplying heavy gauge PVC conduit pipe ....... dia ....... mm thick confirming to IS 2509 with suitable size bends, junction boxes, adhesive paste etc , and fixing using inverted w...

Concealed Conduit System Supplying heavy gauge PVC conduit pipe 19/20mm dia 2 mm thick confirming to IS 2509 with suitable size bends, metal/PVC Junction boxes, adhesive paste etc., and running before...

Concealed Conduit System Supplying heavy gauge PVC conduit pipe ...... mm dia..........mm thick confirming to IS 2509 with suitable size bends, metal/PVC Junction boxes, adhesive paste etc., and runni...

Concealed Conduit System Supplying heavy gauge PVC conduit pipe ...... mm dia..........mm thick confirming to IS 2509 with suitable size bends, metal/PVC Junction boxes, adhesive paste etc., and runni...

Supplying heavy gauge PVC Conduit Pipe .... dia ....... mm thick with suitable size bends, metal junction boxes adhesive paste etc., by groove cutting in the wall and fixing by bracing U or J hooks an...

Supplying heavy gauge PVC Conduit Pipe .... dia ....... mm thick with suitable size bends, metal junction boxes adhesive paste etc., by groove cutting in the wall and fixing by bracing U or J hooks an...

Supplying heavy gauge PVC Conduit Pipe .... dia ....... mm thick with suitable size bends, metal junction boxes adhesive paste etc., by groove cutting in the wall and fixing by bracing U or J hooks an...

Supplying and fixing of PVC casing and capping on the wall or ceiling using necessary materials like bends, junction box, elbows, screws at an interval of 300mm etc. as required 25 mm

Supplying PVC/GI flexible conduit pipe 25mm dia fixing on surface over inverted tapered wooden plugs or phill plugs or rawl plugs and clamped using heavy gauge saddles at an interval of 300 mm using N...

Supplying PVC/GI flexible conduit pipe 32 mm dia fixing on surface over inverted tapered wooden plugs or phill plugs or rawl plugs and clamped using heavy gauge saddles at an interval of 300 mm using ...

Supplying and fixing sheet Metal box made out of 18 SWG sheet metal with necessary holes for cable/conduit entry as required with one coat of primer of approved make etc. 200 x 90 x 65 mm

Point wiring using Copper wire without switch. Supplying and wiring adopting loop system in existing PVC Conduit /casing capping casing capping using 2x1.5mm2 (Phase ...

Point wiring using Copper wire without switch. Supplying and wiring adopting loop system in existing PVC Conduit /casing capping casing capping using 2x1.5mm2 (Phase ...

Point wiring using Copper wire without switch. Supplying and wiring adopting loop system in existing PVC Conduit /casing capping casing capping using 2x1.5mm2 (Phase ...

Point wiring using Copper wire without switch. Supplying and wiring adopting loop system in existing PVC Conduit /casing capping casing capping using 2x1.5mm2 (Phase ...

Point wiring using Copper wire without switch. Supplying and wiring adopting loop system in existing PVC Conduit /casing capping casing capping using 2x1.5mm2 (Phase ...

Wiring for lighting/power circuit using one of FRLS PVC insulated 1100V grade, multistrand copper wire with low conductor resistance single core in open or concealed ...

Wiring for lighting/power circuit using one of FRLS PVC insulated 1100V grade, multistrand copper wire with low conductor resistance single core in open or concealed ...

Wiring for lighting/power circuit using one of FRLS PVC insulated 1100V grade, multistrand copper wire with low conductor resistance single core in open or concealed ...

Wiring for lighting/power circuit using one of FRLS PVC insulated 1100V grade, multistrand copper wire with low conductor resistance single core in open or concealed ...

Wiring for lighting/power circuit using one of FRLS PVC insulated 1100V grade, multistrand copper wire with low conductor resistance single core in open or concealed ...

Wiring for lighting/power circuit using one of FRLS PVC insulated 1100V grade, multistrand copper wire with low conductor resistance single core in open or concealed ...

Supplying and flush mounting powder coated / galvanized metal box suitable for mounting modular switch plates. The box should be firmly flush mounted after due groove cut...

Supplying and flush mounting powder coated / galvanized metal box suitable for mounting modular switch plates. The box should be firmly flush mounted after due groove cut...

Supplying and flush mounting powder coated / galvanized metal box suitable for mounting modular switch plates. The box should be firmly flush mounted after due groove cut...

Supplying and flush mounting powder coated / galvanized metal box suitable for mounting modular switch plates. The box should be firmly flush mounted after due groove cut...

Supplying and flush mounting powder coated / galvanized metal box suitable for mounting modular switch plates. The box should be firmly flush mounted after due groove cut...

Supplying and flush mounting powder coated / galvanized metal box suitable for mounting modular switch plates. The box should be firmly flush mounted after due groove cut...

Supplying and flush mounting powder coated / galvanized metal box suitable for mounting modular switch plates. The box should be firmly flush mounted after due groove cut...

Supplying and flush mounting powder coated / galvanized metal box suitable for mounting modular switch plates. The box should be firmly flush mounted after due groove cut...

Supplying and fixing superior quality modular switch mounting polycarbonate plate with necessary supporting back plate with required nos. of machine screws, bolts nuts etc., compl...

Supplying and fixing superior quality modular switch mounting polycarbonate plate with necessary supporting back plate with required nos. of machine screws, bolts nuts etc., compl...

Supplying and fixing superior quality modular switch mounting polycarbonate plate with necessary supporting back plate with required nos. of machine screws, bolts nuts etc., compl...

Supplying and fixing superior quality modular switch mounting polycarbonate plate with necessary supporting back plate with required nos. of machine screws, bolts nuts etc., compl...

Supplying and fixing superior quality modular switch mounting polycarbonate plate with necessary supporting back plate with required nos. of machine screws, bolts nuts etc., compl...

Supplying and fixing superior quality modular switch mounting polycarbonate plate with necessary supporting back plate with required nos. of machine screws, bolts nuts etc., compl...

Supplying and fixing superior quality modular switch mounting polycarbonate plate with necessary supporting back plate with required nos. of machine screws, bolts nuts etc., compl...

Supplying and fixing superior quality modular switch mounting polycarbonate plate with necessary supporting back plate with required nos. of machine screws, bolts nuts etc., compl...

Supplying and fixing of modular switch & connected accessories on existing modular switch plate as per IS 3854 and IS 1293. 6A One Way Switch

Supplying and fixing of modular switch & connected accessories on existing modular switch plate as per IS 3854 and IS 1293. 6A Three Way socket

Supplying and fixing of modular switch & connected accessories on existing modular switch plate as per IS 3854 and IS 1293. Stepped Fan Regulator Two Module

Supplying and fixing of modular switch & connected accessories on existing modular switch plate as per IS 3854 and IS 1293. 16A One Way Switch

Supplying and fixing of modular switch & connected accessories on existing modular switch plate as per IS 3854 and IS 1293. 6A Bell Push

Supplying and fixing of modular switch & connected accessories on existing modular switch plate as per IS 3854 and IS 1293. 32A DP Switch

Supplying and fixing of modular switch & connected accessories on existing modular switch plate as per IS 3854 and IS 1293. 6/16A Universal Socket

Supplying and fixing of modular switch & connected accessories on existing modular switch plate as per IS 3854 and IS 1293. TV/Telephone Socket

Supplying and fixing of modular switch & connected accessories on existing modular switch plate as per IS 3854 and IS 1293. RJ45/I.O Outlet Cat-6

Extra for supplying 4 mm thick white plastic plate and covering for junction boxes of size 80 mm conduit using necessary machine screws.

Extra for supplying 4 mm thick white plastic plate and covering for junction boxes of size 110 mm conduit using necessary machine screws.

Supplying and fixing one of 230 V Ding dong bell and a flush type bell push with gang box fixed on necessary wooden or rawl plugs using NF screws with Remote. Ding Dong Bell

Supplying of .....feet -PVC Batten with integrated LED tube .... W with high quality diffuser with Life of 25000 burning hours & 70% lumen maintenance with ...

Supplying of .....feet -PVC Batten with integrated LED tube .... W with high quality diffuser with Life of 25000 burning hours & 70% lumen maintenance with ...

Supply of round/square recess/surface mounted rolling type LED Down light with ...... W GU 10 LED Lamp Rib Fabricated from diecast aluminium with...

Fixing all types and all capacities of fluorescent /false ceiling / spot light / CFL / LED fittings indoor on the wall/ ceiling / rafters / girders using 23/0.0076" twin ...

Supplying of Ceiling Fan with Capacitor rating As per guideline of BEE star rated and IS:374/79 and also comply with IS: 1709/1984 with latest amendment, Rated voltage 220 V/50 Hz, Rated power input 4...

Supplying wall mounting fan suitable to operate at single phase 230v AC. supply. 300 mm Sweep

Fixing a ceiling /wall mounting fan of all capacities and all types, with necessary clA and 'S' hook made out of 15mm dia MS rod, with 5 A. ceiling rose of a...

Fixing a ceiling /wall mounting fan of all capacities and all types, with necessary clamps and 'S' hook made out of 15mm dia MS rod, with 5 A. ceiling rose of approved quality with necessary length of...

Extra length of GI pipe of class B 19mm dia for down rod.

Supplying of 1440rpm heavy duty exhaust fan with bracket blades suitable to operate on 230V 50Hz, AC Supply complete. 12" Sweep (300 mm)

Fixing one exhaust fan after making a suitable notch in the wall and finishing with cement mortar and colouring to match the existing wall or brackets, with bolts and nuts and a 5 A, ceiling rose with...

Supplying & fixing of retrofit type - LED bulb ...... W with OPAL acrylic diffuser comprising of LED source with CCT 6500 degree K, CRI 70%. efficacy 80 lumen per W, life 25000 burning hours and Com...

Supplying & Fixing of 70-150 W lamp holder 2 Pin

Supply of LED floodlight luminaire with pressure die cast aluminium housing body for optimal thermal dissipation. Lamp compartment comprising of antiglare clear diffuser with Injection moulded polycar...

Supply of LED floodlight luminaire with pressure die cast aluminium housing body for optimal thermal dissipation. Lamp compartment comprising of antiglare clear diffuser with Injection moulded polycar...

Supply of LED Streetlight luminaire with pressure die cast aluminium housing body for optimal thermal dissipation. Lamp compartment comprising of antiglare clear diffuser with Injection moulded polyca...

Supplying and Fixing of........mm dia class A GI pipe bracket upto 2ms long bent at suitable angle and fixing to this bracket street light fitting of all capacities to GI or GI or rail or RCC pole / w...

Fixing halogen/metal halide /SVL/IL/LED floodlight fitting over existing pole / wall ceiling including clamps, bolts, nuts and wiring using suitable capacity wires

Fabricating, supplying and erection of ... ms long hot dip Galvanized Conical hot dip Pole with BSEN 10025 grade S355JO steel plate for shaft, IS 2062 for base plate with door opening arrangements, in...

Supplying, and fixing of Hot dip Galvanized M.S.Bracket suitable for out door luminaries and mounted on Octagonal pole using necessary bolts, nuts etc., complete. Single Arm Bracket with 1500 mm Stand...

Automatic Switch for Street Light

Supplying and drawing PVC flexible one pair telephone unarmoured tinned copper cable. 2 Pair

Supplying and fixing of MDF krone junction box with KRONE Module / Telephone cable termination. 10 Pair

Supplying, installing, testing and commissioning of Diesel Generator set with following specifications. Power rating as per standard reference condition as per-BS 5514/ISO 3046/ ISO 8528 & IS 1002/ISO...

Supply, Erection, testing and commissioning of AMF panel suitable for .....kVA DG set. The panel is of cubical type base/floor mounting control panel with hinged doors, undrilled bottom gland plate, a...

Supplying fixing and wiring earth electrode for grounding of lifts, transformers, DG sets etc. using 40 mm dia 2.9 mm thick 2.5m long GI pipe with GI funnel with mesh and suitable size reducer fixed o...

GI/Copper strips for grounding connections, using necessary fixing materials as required GI/Copper strips 25 x 6 mm GI strip

GI/Copper strips for grounding connections, using necessary fixing materials as required GI/Copper strips 25 x 6 mm Copper strip

GI/Copper strips for grounding connections, using necessary fixing materials as required GI/Copper strips 600 x 600 x 3 mm Copper plate

RCC Pole - 9 Mtr Long, 145 Kg WL (Dwg No. BESCOM/GM/QS&S/02 Dtd 24.11.2018) as per IS-785

PSCC Pole - 8 Mtr Long, 140 Kg WL (Dwg No. BESCOM/GM/QS&S/17 Dtd 24.11.2018) as per REC Standards

11 kV, Special 3 Pin Cross Arm - GI

HT ST Support 50x8 mm Flat - GI

Spiral Earth Electrode

Anticlimbing Device GI Barbed wire (12 Mtr/Kg)

Guarding for Road crossing, Telephone Line Crossing,between HT & LT Line Crossing

LT 4 Pin Cross Arm - GI

No. 8 Strain Insulator

RCC Pole Clamp - GI

11 kV GI Pin for 11 kV Ceramic Shell Insulator

DISC Insulator 45 kN Porcelain

Rabbit ACSR (6/3.35 mm Al + 1/3.35 mm St), Std Wt: 214 Kg/KM

7/10 SWG Guy Wire (7/3.251 mm Dia), Std Wt: 680 Kg/KM

PG Clamp Rabbit to Rabbit

9 kV, 5 kA Lightning Arrester Metal Oxide Ceramic type with GROUND DISCONNECTOR (Dwg No. BESCOM/GM/QS&S/26 Dtd 24.10.2007)

11 kV, HG Fuse Unit with Solid Core Insulator (Dwg No. BESCOM/GM/QS&S/21 Dtd 24.11.2018)

For 100/300 kVA 4/5 Star Rated Transformer on RCC Pole - 9 Mtr Long, 145 Kg WL - GI

Three H Frame with Transformer Seating and Seating angle support cross arm for 11 Mtr Spun Pole up to and including 250 kVA (UG Cable)) - GI

11 kV, 200 Amps Single Break GOS (Dwg No. BESCOM/GM/QS&S/23 Dtd 24.11.2018)

11 kV, DOLO Cutout Conventional to Erstwhile KEB pecification

Transparent Alkathine tube 19 mm dia, 2 mm thick in coils of 30 Mtr

Caution/Danger Board

Digging of Pit 1.8 Mtr depth for errection of 9 to 10 Mtr Long Steel/RCC/PSCC supports as per approved Drawing. Hard Soil

Digging of Pit for GUY SET Hard Soil

Erection of RCC/PSCC Pole of 9 to 10 Mtr long in a pit of 1.8 Mtr depth

Providing Spiral Earth Electrode type earthing (without charcoal, salt etc.,)

For Three H Frame without Transformer Seating and Seating angle support cross arm for 11 Mtr Spun Pole up to and including 250 kVA (UG Cable) (excluding erection of Pole)

Fixing of 4 Pin cross arm with Insulator and Braces fixing

Fixing of HT/LT Single Top Support

Fixing of GUY Set with break insulator making use of 7/3.15 mm (7/10 SWG) galvanised steel wire with turn buckle and anchoring arrangement as per approved drawing. (Excluding excavation of PIT

Stringing of conductor Rabbit ACSR, binding of conductor on each insulator and dead ending on strain or disc /strain insulator by means of clamps.

Fixing DOLO Cutout/Horn Gap Fuse including fixing of cross arm and wiring

Fixing of GOS including wiring (11 kV Single Break 200 Amps)

Numbering and Scheduling of Pole

Distribution Transformer - 3 Phase, 11kV/433V - Stacked CRGO Core with Oil as per IS-1180 (Part-1): 2014 B. CABLE ENTRY TYP 250 kVA, Aluminium Wdg, Star 1 (4 Star)

LT Distribution Box for 100/250 kVA DTC with MCCBs (SMC)

3 Phase CT/PT operated alternating current Smart Meter of Accuracy Class 0.2s DLMS with GPRS Communication Module

11 kV HT Metering cubicle of different CT Ratio, Both side cable entry type with 3 CT & 3 PT, With Transparent Cover TTB, with 30x8 mm Copper Busbar, Modem & 2 No of Meters for 3 Phase 4 Wire Metering...

Erection of 200 - 250 kVA Transformer

Erection of HT metering Cubicle on Platform

11 kV, 3 Core, XPLE HTUG Cable with pressure extruded inner sheeth, ROUND WIRE ARMOURED as per IS-7098 (Part-2) Armouring wires dia and Resistivity as per IS-3975 95 Sqmm, (54 GI Wires - 2.5 mm Dia)

Heat Shrinkable Indoor Type Cable Termination Kit for XLPE Cable 3x95 Sqmm

Heat Shrinkable Outdoor Type Cable Termination Kit for XLPE Cable 3x95 Sqmm

Laying of cable in Existing Trench/GI pipe/Stone Ware/RCC Hume pipe using Wooden/Aluminum Rollers as directed by the departmental staff HT Cable 3x95 to 150 Sqmm

1.1 kV, XLPE or Heat resistant PVC insulated, PVC extruted Inner Seath Armoured LTUG Cable as per IS1554 (Part1) or IS7098 Part1, Armouring strip thickness and resistivity as per IS 3975-185 Sqmm 3.5 ...

1.1 kV, XLPE or Heat resistant PVC insulated, PVC exutruted Inner Seath Armoured LTUG Cable as per IS-1554 (Part1) or IS-7098 Part-1, Armouring strip thickness and resistivity as per IS-3975 120 Sqmm,...

1.1 kV, XLPE or Heat resistant PVC insulated, PVC exutruted Inner Seath Armoured LTUG Cable as per IS-1554 (Part1) or IS-7098 Part-1, Armouring strip thickness and resistivity as per IS-3975 25 Sqmm, ...

1.1 kV, XLPE or Heat resistant PVC insulated, PVC exutruted Inner Seath Armoured LTUG Cable as per IS-1554 (Part1) or IS-7098 Part-1, Armouring strip thickness and resistivity as per IS-3975 50 Sqmm, ...

Heavy Duty Copper Terminal Long Barrel 25 Sqmm Copper Terminal, Apprx Wt: 11 Gm

Heavy Duty Copper Terminal Long Barrel 50 Sqmm Copper Terminal, Apprx Wt: 26 Gm

Heavy Duty Copper Terminal Long Barrel 95 Sqmm Copper Terminal, Apprx Wt: 58 Gm

Heavy Duty Copper Terminal Long Barrel120 Sqmm Copper Terminal, Apprx Wt: 64 Gm

Heavy Duty Copper Terminal Long Barrel 185 Sqmm Copper Terminal, Apprx Wt: 158 Gm

Brass Cable Gland 25

Brass Cable Gland 32

Brass Cable Gland 40

Route & Joint indicating slab with MS Anchor rod

Laying of cable in Existing Trench/GI pipe/Stone Ware/RCC Hume pipe using Wooden/Aluminum Rollers as directed by the departmental staff LT Cable 2.5 to 25 Sqmm

Laying of cable in Existing Trench/GI pipe/Stone Ware/RCC Hume pipe using Wooden/Aluminum Rollers as directed by the departmental staff LT Cable 35 to 95 Sqmm

Laying of cable in Existing Trench/GI pipe/Stone Ware/RCC Hume pipe using Wooden/Aluminum Rollers as directed by the departmental staff LT Cable 120 to 240 Sqmm

Fabricating supplying and mounting MS box made out ....SWG suitable for floor /wall mounting, fully weather proof with provision for better heat dissipation, provided with hinged front cover, equipped...

Supplying, fixing and wiring 50/5 to 400/5A 5VA burden Current Transformer Class 0.5 accuracy with Tape Wound.

Supplying and fixing Electronic Trivector Meter (ETV)suitable for operation LT operation and - CT operated meter in polycarbonate body in class0.5 accuracy as per IS 14697 and completely wired.

Supplying and fixing of Shunt trip suitable for MCCB.CBCT

Supplying, fixing and wiring earth leakage relay with core balanced current transformer suitable for single phase 50 Hz AC with latest microcontroller based, digital readout of percentage leakage curr...

Supplying and fixing of LED type panel board indicating lamp with required colour suitable for 230/440VAC. 50 Hz 12/24V D.C

Supplying & fixing miniature circuit breakers on existing MCB distribution boards using necessary fixing materials and 'C' Type curve, indicator ON/OFF, e...

Supplying of multi function digital meter with three line back light LCD type display for voltage, Current, frequency, Power, power factor, kVA, kWH, kVAR suitable for 3 phase, 4 wire LT network with ...

Supplying and fixing Moulded Case Circuit Breaker (MCCB) over the existing wood/panel board using necessary screws, bolts, nuts, necessary phase separators, handle and wiring complete. Protection of O...

Supplying ......... A rated 3phase with neutral bus bar using required capacity electrolytic aluminium strips covered with heat shrinkable coloured PVC sleeve, mounted on phenolic/FRP/DMC insulator wh...

Supplying and fixing Moulded Case Circuit Breaker (MCCB) over the existing wood/panel board using necessary screws, bolts, nuts, necessary phase separators, handle and wiring complete. Protection of O...

Supplying and fixing Moulded Case Circuit Breaker (MCCB) over the existing wood/panel board using necessary screws, bolts, nuts, necessary phase separators, handle and wiring complete. Protection of O...

Rotary handle for MCCB

Supplying & fixing miniature circuit breakers on existing MCB distribution boards using necessary fixing materials and 'C' Type curve, indicator ON/OFF, e...

Supplying of on load change over switches 4poles, AC-23A Duty,415V,50Hz,ACSupply.With all accessories. (SM Enclosure Sheet Metal Execution) 100 A

Supplying ......... A rated 3phase with neutral bus bar using required capacity electrolytic aluminium strips covered with heat shrinkable coloured PVC sleeve, mounted on phenolic/FRP/DMC insulator wh...

Supplying & fixing miniature circuit breakers on existing MCB distribution boards using necessary fixing materials and 'C' Type curve, indicator ON/OFF, e...

Supplying & fixing miniature circuit breakers on existing MCB distribution boards using necessary fixing materials and 'C' Type curve, indicator ON/OFF, e...

Supplying and fixing angle iron frame work fabricated out of M.S.angle iron.. and M.S. Flat......with bolts, washers etc., and painted with 2 coats of red oxide and then two coats of approved paint. 5...

Supplying and fixing regular MCB distribution boards on wall/ood board / flush mounting using required clA, bolts, nuts etc., with provision for fixing s...

Supplying, fixing and wiring Residual current circuit breaker (RCCB) 240/450V upto 300mA sensitivity on existing wood/ panel board. 32-40A 2 pole

Supplying & fixing miniature circuit breakers on existing MCB distribution boards using necessary fixing materials and 'C' Type curve, indicator ON/OFF, e...

Supplying and fixing regular MCB distribution boards on wall/ood board / flush mounting using required clA, bolts, nuts etc., with provision for fixing s...

Supplying, fixing and wiring Residual current circuit breaker (RCCB) 240/450V upto 300mA sensitivity on existing wood/ panel board. 63 A 4 pole

Supplying & fixing miniature circuit breakers on existing MCB distribution boards using necessary fixing materials and 'C' Type curve, indicator ON/OFF, e...

Supplying & fixing miniature circuit breakers on existing MCB distribution boards using necessary fixing materials and 'C' Type curve, indicator ON/OFF, e...

Supply of Fabricated main frame for housing refractory bricks and other equipment, Furnace the main door, Furnace supporting frame, Main door lifting mechanism by hydraulic system, Hand pump is provid...

Supply of Refractory Materials Supply of refractory bricks, body laying bricks, Arch bricks slabs & binding agents (mortar, castable & Fire clay etc.) Materials used to construct the furnace Chamber (...

Supply of Heating coil Coils are made out of Kanthal APM of 8 Guage wire / Nichrome wire of 8 Gauge with terminal rods. Each coil apx. 3.5Kw capacity, Total 12 no coils (42 Kw) Housed in an S S 310G p...

Supply, Installation, Testing, & Commissioning of Body ChargingTrolleySupply of fabricated Hydraulically operated Body Charging Trolley with power pack and connecting pipelines and control desk to ope...

Supply, Installation, Testing, & Commissioning of Electric Remote Control panel.The control panel is built with the following components housed in Panel made out of MS sheet duly powder coated, with f...

Supply, Laying, Testing, & Commissioning of Control & Power CablesSupply of power cables, bus bar laying, supporting tray, conduit pipes, from the control panel to various equipments, heating coils, m...

Supply, Installation, Testing, & Commissioning of Water pump Supply of water pump for scrubber unit.1 Hp motor, 3 Phase, 415V, for circulating the water in wet venture scrubber unit and necessary pipe...

Supply, Installation, Testing, & Commissioning of Fresh air blower Made out of MS Sheet, direct driven motor of 1 Hp, 3 Phase, 415V, ot suitable capacities, mounted on a MS rigid angle frame, connecte...

Supply, Installation, Testing, & Commissioning of Scrubber unit Wet scrubber unit with venturi rrangements made out of S S 304G sheets. In unit-1 smoke will completely come in contact with water and p...

Supply, installation, Testing, & Commissioning of online-Exhaust Blower Fabricated with an S S 304G sheet, the impeller driving shaft is also made out of S S with bearing support mounted on a suitable...

Erection charges for Erection, testing, commissioning, handing over the cremation furnace (a) Fixing of Frame, Main Door, Counterweight, Mechanical and Electrical operating door system. (b) Refractor...

Packing, forwarding, Loading, and Unloading charges from our factory in Bangalore to the crematorium site.

Supply, Installation, Testing, & Commissioning of Self-supporting chimney.The chimney is made out of MS Plates, angles, flats, grouting bolts & gusset plates, ladder, platform with a protection cage u...