Renovation of Dy. CAO office complex phase-II at BBMB Sundernagar

Amount

Dismantling concrete(c ) Cement concrete plain 1:3:6 mix

Dismantling plank ceiling and supporting timber

Removing doors and windows together with the dismantling of walls Door+ almirah Door.

Clerestory windows/Ventilator

Scraping (a)White wash and colour wash

Nicking cement concrete surface (over 28 days old including preparation and laying slurry

8” thick H.B. Masonry in 1 : 5 cement mortar in superstructure. Ventilator under Window.

12.5 mm thick cement plaster 1:5

Cement concrete 1:5:10 ( b) With stone aggregate 40mm gauge (ii) mixing by mechanical means using concrete mixer volumetric type

Providing and laying vitrified floor tiles in different sizes in light colour shades made using sotuble Salt Technology (thickness to be specified by the manufacturer) with water absorption’s less than 0.08% and conforming to IS : 15622 of approved make in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement: 4 fine sand), complete. ( Sotuble salt Print Penetration should be up to 1to 2mm after the tiles are fired & polished). (a)Size 600x600 mm

Kota stone slab 20-25 mm thick flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) :

Supplying Pressed steel sheet frames (chowkhat) consisting of 18 gauge (1.25 mm thick steel sheet of the specified section, including iron lugs (hold fast) iron hinges conforming to PWD specification including bolts for fixing stops lock notch provision for receiving tower bolts and finished with 1 primer coat approved quality, fixed in position excluding the cost of cement concrete 1:3:6 for fillings in the frame and cement concrete 1:2:4 for lugs complete. (c ) Doors and windows frame of size 151mm x 60mm with 35 mm wide double rebate weighing 3.95 kg per meter.

Providing and fixing M.S. angle iron 40x40x6mm chowkhat including iron hold fasts butt hinges fixed in position, finished with red lead non setting primer complete in all respect. (a) For single rebate.

Supplying open able steel windows, of standard rolled steel Z sections, joints mitered and Electrically flash-welded, with iron fittings including necessary iron handles, Peg-stay catchers bolts, iron plugs and pressed steel projected hinges and glazing clips, complete (Excluding glazing ) and finished with two coats of ready mixed paint red lead non setting primer. (b) Above one sqm Area

Providing and fixing M.S. round or square bars at required spacing in wooden frames of windows and clearstory windows.

Wire gauge fixed in steel windows, of standard rolled steel section with 3mm thick flat iron cover moulding of 12.5 mm width, fixed with machine screws, complete in all respects.

Supplying and fixing glass panes with glazing clips and special metal sash putty of approved ake. (B) Glass panes 4mm or 10.75 kg / sqm exceeding 0.4 sqm of area

Factory manufactured flush door fixed in position iron hinges, etc (excluding the cost of any fittings other than specified above but including labour for fixing the same in position (Code : II Revision IS-2191Part-I)1973. (a)Commercial with elm or gurjan facing on both \ Sides with laminated core and lipped edges: 35 mm

Factory manufactured flush door fixed in position iron hinges, etc (excluding the cost of any fittings other than specified above but including labour for fixing the same in position (Code : II Revision IS-2191 Part-I) 1973 (iii) 30 mm thick

Wire gauze door shutter with Kail wood without springs housed in chowkats (Single Leaf) (a)35mm thick

Providing and fixing helical door spring 150mm (superior quality) including necessary screws, complete.(a) Brass helical spring.

Cost of aluminum fittings complete for doors, windows such as tower bolts, handles, Stoppers and screw etc. for these fittings (Excluding sliding bolt)(ii) For shutter area above 0.50 sqm

Providing and fixing aluminum sliding door bolts ISI marked anodized (anodic coating not less than grade AC 10 as per IS :1868) transparent or dyed to required colour or shade with nuts and screws etc. complete :(A) 300mm x 16mm

Structural steel work in angles, tees, flats, riveted, including cutting, fixing all gusset plates, bolts, nuts, rivets etc. with hoisting and erecting in position.(a) For roof truss, well curbs, plate girders etc. of any span for building for bridges upto 15M span

Providing & fixing 4 mm thick multipurpose cement board conforming to IS : 14862 : 2000 for false ceiling duly screwed with frame with nuts & bolts of size 20 x 3mm for anchoring channels in position.

Steel work fixed independently without connecting plates including cutting hoisting and fixing in position.(c ) Tees angles & channels.

10 mm thick cement plaster 1:3.

Applying priming coat with metal primer on new steel or iron work including preparation of surface.

Applying pink primer or aluminum priming coat on wood work including preparation of surface knotting and stopping etc.

Painting two or more coats excluding priming coat with synthetic enamel paint in all shades on wood work, metallic or plastered, concrete surface to give an even shade.

Distempering with Acrylic washable oil bound distemper (of approved manufacture) two or more coats over one priming coat to give an even shade.

Finishing walls with exterior decorative cement based paint such as snowcem, robbiacem etc. two or more coats to give an even shade.

Kotah stone tiles 20mm thick in skirting risers of steps, dado walls and pillars laid in 12.5mm thick cement mortar 1:3 (1 cement 3 coarse sand) and jointed with neat cement slurry mixed with pigment to match the shade of stone, including rubbing and polishing.

(B) Electrical Items : SURFACE PVC CONDUIT PIPE WIRING SYSTEM WITH FLUSH PIANO TYPE SWITCHES: Wiring in PVC insulated copper conductor single core FR cable (ISI marked) overall 1.5sq. mm, 1100volts grade to be laid in heavy gauge PVC conduit pipe 20mm/ 25mm dia (ISI Marked) installed on surface etc., complete with PVC boxes (Plastic on surface boxes) required for having (Flush/ Piano type accessories) Step type electronic fan regulators 100watts (socket size), bell push, 5Pin 6Amp. (4Module Box), 16Amp. Universal sockets (6Module Box), 6/16/20Amp. Switches etc. and covered with brown bakelite white glazed translucent backside painted sheet 3mm thick etc., PVC connector (For Fan Box and Call Bell), MS saddle clamp, PVC Circular junction Boxes (Four way 1½" deep for walls), bonding to earth with PVC insulated copper conductor single core FR cable (ISI marked) 1sq. mm, 1100volts grade (For 6Amp. wall socket & plug control point) and other petty material etc., including the cost of above material and painting as required:- (i) Wiring fan point (Without fan box)

(ii)Wiring light point

(iii)Wiring call-bell point

(iv)Wiring 6Amp. Plug control comprising wall socket point

(v)Wiring 16/20Amp. power plug control point

PVC INSULATED FR COPPER CONDUCTOR CABLES: Supply and erection of PVC insulated FR single core Unsheathed copper conductor cable (ISI marked) suitable upto 1100 volts grade confirm to IS:694/1990 left bare in pipe or casing of suitable size complete in all respect as desired by the Engineer-in-charge:- (i) Overall size 2.5sq.mm (Un-sheathed)

(ii) Overall size 4sq.mm (Un-sheathed)

(iii) Overall size 6sq.mm (Un-sheathed)

MINIATURE CIRCUIT BREAKERS: Supply and erection of Miniature Circuit Breaker MCB's for circuit protection against overload and short circuit current fault suitable for 240/ 415 volts 50cycles AC supply with breaking capacity of 10kA, Curve-C and low watt losses as per IS/IEC 60898-1, energy limitation class-3, true contact indication, label holder facility in the existing MCB distribution board as per PWD General Specifications including connections with suitable size of thimbles/lugs:- (i)MCB Single Pole 0.5-4amp. (10kA, Curve-C)

(ii) MCB Single Pole 6-32amp. (10kA, Curve-C)

(viii) MCB Double Pole 50, 63amp. (10kA, Curve- C)

(xvi) MCB Four Pole 50, 63amp. (10kA, Curve-C)

SHEET METAL DOUBLE DOOR DISTRIBUTION BOARD FOR MCB's/ RCBO's/ RCCB's: Supply and erection of sheet metal Double Door Distribution Boards IP 43- IK09 metal door (dust protected) as per IS 8623-1&3, IEC 61439-1&3 suitable for flush mounting with fully insulated copper busbars, shrouded neutral bars, earth bars, cement spill protector, color coded interconnecting wire set, cable ties, blanking plates and circuit identifications label and of required no. of ways for mounting miniature circuit breakers/ RCBO's/ RCCB's in the distribution board (For SP&N distribution board with provision DP MCB's/ RCCB's/ RCBO's as incomer and SP MCB's as outgoings and for TP&N horizontal distribution board with provision TPN/ FP MCB's/ RCCB's/ RCBO's as incomer and SP MCB's as outgoings) as per PWD General specifications including connections with suitable size of thimbles and bonding to existing earth etc:- (ii) SP&N Double Door Distribution Board 8 way each

(iii) SP&N Double Door Distribution Board 12 way each

(v) TP&N Horizontal Double Door Distribution Board 4 way each

SHEET METAL IRON CLAD SWITCHES: Supply and erection of sheet metal Iron Clad Switches on existing surface with G.I. bolts & nuts/ rag bolts and nuts etc., according to the size of holes in the body of the enclosure including connections with suitable size of thimbles and bonding to the existing earth as Per PWD General Specifications:- (x) ICTPN Switch 400amp., 415volts.

SHEET METAL BUS BAR CHAMBERS (COPPER STRIPS): Supply and erection of sheet metal busbar chamber (factory fabricated) duly powder coated on existing surface with required 4 Nos. of tin plated copper busbar strips of suitable length and cross sectional area mounted on DMC/ SMC moulds at sufficient distance, enclosure made of M.S. sheet 1.6mm thick with hinged cover and lock, fitted with dust excluding gaskets and secured with sufficient no. of cadmium plated iron screws and of given overall dimensions and to be fixed with G.I. bolts and nuts/ rag bolts and nuts etc. complete with all accessories including connections with suitable size of thimbles, bonding to the existing earth and painting etc. as desired by the Engineer-in-charge at site:- (ix) Bus Bar Chamber 200amp., 415volts Overall Dimensions (780mm x 510mm x 215mm) nominal

LED Tube light 18/20W

Led Blub 6/7W

XLPE INSULATED ARMOURED CABLES (ON SURFACE):Supply, laying and erection of aluminum conductor XLPE insulated PVC sheathed armoured and served cable 1100 volts grade as per IS:7098 (Part-1)1988 to be laid (On Surface) as per PWD General Specifications:- i) Overall size 70sq.mm (3 ½ Core) Armoured (On-Surface)

Bidder Name

Amount in Words

M/S SHARMA ELECTRICAL WORKS

RAKESH KUMAR

SHIV KUMAR

SHIV KUMAR

RAKESH KUMAR