Construction of additional block at JLNM hospital RAINAWARI Srinagar under Languishing

Amount

CIVIL WORKS

Brick work with common burnt clay (non-modular) bricks of class designation 7.5 in superstructure above plinth level upto floor five level icluding curing Cement mortar 1:6 ( 1 cement : 6 coarse sand)

15mm cement plaster on the rough side of single or half brick wall of mix 1:6 (1 cement: 6 fine sand) (including cost of all material, leads, lifts and carriages etc upto site of work complete).

12 mm thick cement plaster on ceilings, soffits etc. in (1 cement: 4 fine sand mix). Upto floor V level complete in all respects (including cost of all material, leads, lifts and carriages etc. upto site of work complete).

Providing and applying ornamental molded cementing plaster vertical post with mix of 1 cement and 1 fine sand(1 :1 mix ) including material scuffolding shuttering etc complete job as per architectural drawing/ and approved by consultant / client

Providing and fixing of U-PVC sliding/casement/fix doors in white colour,frame 60mm thick (min) x 45mm (min) with 1.5 mm GI reinforcement sash 39mm (min) 58mm (min) with 1.25mm GI U section reinforcement with rubber gasket of grey / black colour 10 years warranty against weathering of profile with complete hardware fittings fixed with 8mm thick high pressure laminated board panels as per design and with 5mm toughened glass and fiber jalli option if pre- febricated on german fabrication system( mosquito sash 18mm(min) x 43mm(min)(with welled cornes) complete at site including all fixtures

Providing and fixing of powder coated aluminum work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Zsections and other sections of approved make conforming to IS: 733 and IS: 1285, fixed with dash fa stener of required dia. and size including necessary filling up of gaps at junctions i.e, at top, bottom and sides with required EPDM rubber / neoprene gasket felt etc. Aluminum sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminum snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge

Providing and Fixing 8mm thick HPL sheets matt finish in doors and partition walls etc complete as per architectural drawings and the directions of engineer in charge

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia and length (hold fast lugs or with dash fasteners shall be paid for separately): First class deodar wood.

Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge.35mm of First class kail wood

Providing and fixing wire gauze shutters using galvanized M.S. wire gauze of average width for aperture 1.4 mm in both directions with wire of dia. 0.63 mm for doors, windows and clerestory windows with ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws as per direction of Engineer-in-charge :35mm of first class kail wood

Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embeddings in cement concrete block 30x10x15 cm 1:3:6 mix ( 1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size).

Providing and fixing ISI marked flush door shutters 35 mm thick conforming to IS: 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. With ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws

Providing and fixing plannes eaves boarding (300mm x 40mm )( nominal size) second class dewdare wood fixed with screws etc, including all carraiges .All job completed

Providing and fixing 20mm thick wooden planks ceiling/ soffit(frame work for base to be paid for separately) with M.S. screws 2nd class kail wood

Providing colour coated sheet roofing including vertical/curved surface fixed with polymer coated J or L hooks, bolts and nuts 8mm diameter with bitumen and G.I limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (upto any pitch in horizontal/vertical or curved surface)excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. 0.5 mm thick

Providing corrugated G. S. sheet roofing including vertical/curved surface fixed with polymer coated J or L hooks, bolts and nuts 8mm diameter withbitumen and G.I limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (upto any pitch in horizontal/vertical or curved surface)excluding the cost of purlins, raftersand trusses and including cutting to size and shape wherever required.0.50 mm thick with zinc coating not less than 275 gram/m

Providing ridges or hips of width 60cm overall width plain G.S. sheets fixed with polymer coated J. or L hooks, bolts and nuts 8mm dia G.I. limpet and bitumen washers complete. 0.80 mm thick with zinc coating not less than 275 gram/m

P/F of 5mm sheet glass ordinary fixed with aluminium frame work including the cost of fittings and fixtures approved specifications(5mm thick)

Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door shutters (over all area of door shutter to be measured)

Providing and fixing 4mm thick of clear plain glass for fixed glazing panels/ shutters (only panel area to be measured) including cost of teak wood beadings of required size complete.

Providing and fixing of aluminium hardware fitings

tower bolt (barrel type) 100 x10 mm

handles 100 mm

150 mm hooks and eyes

L-drop 250mm

tower bolt (barrel type) 150 x10 mm

handles 125 mm

butt hinges of 125x75x4 mm

butt hinges of 100x63x3.2 mm

Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours and shades, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), including grouting the joint with white cement and matching pigments etc. complete. ;

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer- in-Charge, in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 (1 cement :3 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm, including pointing in white cement mixed with pigment of matching shade complete

Providing and fixing ( gang saw cut mirror polished (flamed , pre-moulded and pre-polished), machine cut for flooring, steps ,risers of stairs etc.( flamed instaircase) of required size of approved shade, colour and texture laid over 20mm thick base cement mortar 1:4 (1 cement : 4 coarse sand) with joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding (of edges wherever required ) and polishing to edge to give high gloss finish etc. complete at all levels. Granite of any colour and shape 18mm thick. (Note: The Granite stone slab shall be cut to required size and laid to the required pattern including rounding, chamfering, bull nosing of the edges as directed. Actual area of slab, as laid shall be measured) Sample to be approved by Engineer-in-charge. (including cost of all material, leads, lifts and carriages etc. upto site of work complete.

Providing and fixing Antiskid Vitrified pavement tiles (ramp tiles ) 300x300x10 mm laid on a 20 mm thick cement mortar 1:4 1 cement : 4 coarse sand and jointing with tile grout as per directions of engineer in charge.

Providing and fixing Antistatic Conductive Tiles Flooring, Seamless Antistatic Conductive Tiles Flooring, 2mm thick, with grounding Strips, perfectly curved Flushing corners, all joints welded properly all complete as per the directions of consultant. as per the directions of Consultant/as per the drawings enclosed

Providing and applying 2mm thick white cement based putty of specified thickness, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Providing and applying primer coats of approved brand with water thinnable cement primer on wall surface having low VOC complete.

Finishing walls with water proofing cement paint of required shade on New work (two or more coats applied @ 3.84 kg/10sqm)

With ready mixed pink or grey primer of approved brand and manufacture on wood work (hard and soft wood)

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade. Two or more coats on new work.

French spirit polishing, Two or more coats on new works including a coat of wood filler

Providing wood work in frames of false ceiling, partitions etc. sawn and fixed in position : Budloo wood

Supply and installation signage plates for rooms.meeting halls etc of size 120mm x120mm x1.5mm in ss304 matt finish having letters engrave in the ss plate in black vinyl steam pressed to get a clean finish and having font size of name atleast 30mm fixed on the wall or door surface with high quality adhesive tape of 3M or equivalent complete to thesatisfaction of engineer in charge

Proving and fixing of 12mm thick t&g planks made of imported wood panelling pine or equivalent for wall panneling . including cost of necessary adhesive. and cost of nails etc complete job

Proving and fixing of 12mm thick ply for wall . including cost of necessary adhesive. and cost of nails etc complete job

Providing and fixing thermal insulation with specified wool and density conforming to IS: 8183, 50 mm thick, wrapped in 200G Virgin Polythene bags fixed to walls with screws, rawl plugs and washers and held in position by criss-crossing GI wire etc. complete as per directions of Engineer-in-charge.With resin bonded fiber glass wool with density 24 kg/cum

Providing & Fixing of Armstrong/Equivalent make Mineral Fibre Acoustical Suspended Ceiling System with DUNE or Equivalent(Bevelled Tegular) Edge Tiles With 15mm Exposed GRID. The tiles should have Humidity Resistance (RH) of 99%, NRC 0.5, Light Reflectance ≥85%, Thermal Conductivity k = 0.052 - 0.057 w/m K, Colour White, Fire Performance UK Class 0 / Class 1 (BS 476 pt - 6 &7) in module size of 600 x 600 x 16mm , suitable for Green Building application, with Recycled content of 32%. The tile shall be laid on 15 mm wide T - section flanges colour white having rotary stitching on all T sections i.e. the Main Runner, 1200 mm & 600 mm Cross Tees with a web height of 38mm and a load carrying capacity of 14Kgs/M2 & minimum pull out strength of 100 Kgs.. The T Sections have a Galvanizing of 90 grams per M2 and need to be installed with Suspension system of approved make. ( The rate shall include making provision for light fixtures, AC grilles difusres etc). (ITEM CONTINUED IN 38.1)

INSTALLATION:To comprise main runner spaced at 1200mm centres securely fixed to the structural soffit using Armstrong suspension system (specifications below) at 1200mm maximum centre. The First/Last suspension system at the end of each main runner should not be greater than 450mm from the adjacent wall. Flush fitting 1200mm long cross tees to be interlocked between main runners at 600mm centre to form 1200 x 600 mm module. Cut cross tees longer than 600mm require independent support. 600 x 600mm module to be formed by fitting 600mm long flush fitting cross tees centrally between the 1200 mm cross tees. Perimeter trim to be wall angles of size 3000x19x19mm, secured to walls at 450 mm maximum centres. Installation to be carried out by Armstrong Trained Installation team & Installation should be carried out as per recommended procedure. SUSPENSION SYSTEM accessories manufactured and supplied by Armstrong World Industries consisting of M6 Anchor Fasteners with Vertical Hangers made of Galvanised steel of size 26 x 26 x 25 x 1.2mm with a Galvanised Thickness of 80gsm, A pre Straightened Hanger wire of dia – 2.5 mm of 1.8 m length., thickness of 80gsm and a tensile strength of 344-413 MPa, along with Adjustable hook clips of 0.8mm thick, galvanised spring steel for 2.68 mm with a minimum pull strength of 110 kg. The adjustable clip also consists of a 3.5 mm aquiline wire to be used with the main runner.

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS:277 and consisting of angle cleats of size 25 mm widex1.6mm thick with flanges of 27mm and 37 mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm diax40mm long with 6 mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.5mm of required length with nuts & bolts of required size and other end of angle hanger fixed with G.I. channels 45x15x0.9 mm running at the spacing of 1200 centre to centre, to which the ceiling section 0.5mm thick bottom wedge of 80mm with tapered flanges of 26 mm each having clips of 10.5 mm at 450mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64mm diaX230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5mm thick 27mm high having flanges of 20mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre to centre, with 25mm long drive-all screws (ITEM CONTINUED IN 39.1))

@ 230 mm interval ,including fixing of gypsum board/calcium silicate board to ceiling section and perimetre channel with the help of dry wall screws of size 3.5x25mm at 230mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the gypsum board with recommended jointing compound, jointing tapes, finishing with jointing compound in 3 layers covering upto 150mm on both sides of joint and two coats of primer suitable for board, all as per manufacturers’ specification and also including the cost of making openings for light fittings, grills diffusers, cutouts made with frame of perimetre channels suitably fixed all complete as per drawing and specification and direction of the Engineer-in-Charge but excluding the cost of painting with 8 mm thick Calcium Silicate Board made with Calcareous andSiliceous materials reinforced with cellulose fiber manufactured through autoclaving process.

Providing and Fixing of 50mm dia stainless steel railing of 304 grade of hallow tube 1.6 mm thick of Jindal/Salem make or equivalent including welding and fixing with stainless steel machine screws for making required size and shape, buffing etc. Complete and fixing stainless steel balusters upto 900 mm height and S S tubes, three in one installed horizontally including cutting, welding, grinding to required shape and size by required steel dash fasteners, nuts, bolts, screws ,etc. in floors and treads including providing SS shoe at each balusters complete as per architectural drawings and as per the directions of engineer incharge including cutting of granite/marble floors and fastening with lead grouting if required, complete in all respects.

Providing and Fixing of 50mm dia stainless steel railing of 304 grade of hallow tube 1.6 mm thick of Jindal/Salem make or equivalent including welding and fixing with stainless steel machine screws for making required size and shape, buffing etc. Complete and fixing stainless steel balusters upto 900 mm height and S S tubes, three in one installed horizontally including cutting, welding, grinding to required shape and size by required steel dash fasteners, nuts, bolts, screws ,etc. in floors and treads including providing SS shoe at each balusters complete as per architectural drawings and as per the directions of engineer incharge including cutting of granite/marble floors and fastening with lead grouting if required, complete in all respects.

Providing & fixing of stainless steel nevel post (Ornamental ) including top ball of AISI 304 grade of required height duley anchored to floor with dash fasteners . Height of the nevel post shall not be less than 1050 mm above the finished skirting level all complete as per architectural drawings (including cost of all material, leads, lifts and carriages etc upto site of work complete).Complete as per the directions of Engineer incharge.

Providing and fixing fasle partation wall upto a specified height on the back of Beds (for Bed head panel /Console) 1200 mm high x 230 mm deep(min) made up of 19 mm thick Ply board waterproofing having Frame of Ist .class budloo wood Frame of 100 mm x 50 mm in section placed vertically/horizontally as per design of consultant finished top with granite and sides with laminated 0.8mm laminated sheets on exposed surfaces fixed with adhesive/screws/nails wherever required including inside painting on exposed surfaces including all necessary fittings of Ist Quality as required all complete as per the directions/instructions of Engineer in charge

Earth work in bulk excavation over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 m2 on plan) including disposal of excavated earth lead upto 50 meters and lift upto 1.5 m, as directed by Engineer-in-Charge. All kinds of soil

Earth work in excavation in trenches for foundations, drains, pipes, cables etc. (not exceeding 1.5 m in width) and for shafts, wells, cesspits and the like not exceeding 10 sqm on plan, including dressing of sides and ramming of bottoms lift upto 1.5 m, including getting out excavated earth and disposal of surplus excavated earth as directed, within a lead of 50 metres:in All kinds of soil

providing and laying hand packed stone aggregate 63-150mm of nominal size

Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size)

Providing and laying in position specified grade of reinforced cement concrete including curing but excluding the cost of centering, shuttering, finishing and reinforcement. All works upto plinth level in 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)

Providing and laying in position specified grade of reinforced cement concrete including curing but excluding the cost of centering, shuttering, finishing and reinforcement. All works upto plinth level in 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone 20MM nomial size

Providing and laying in position cement concrete of specified grade floors, bed blocks etc including curing but excluding the cost of centring and shuttering. For all floor levels'in 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)

Form work of steel plates not less than 3.0mm thick M.S. sheets of specified size stiffened with suitable structural frame work true to plane or Kit-ply plates of not less than 12mm thickness of specified sizes stiffened with a suitable timber frame work prop height up to desired height in foundation, plinth beams, all types of suspended floors, soffits of slabs, sloping areas, sides and soffits of beams ribs, columns posts, pedestals, up to desired heights and thickness complete including its removal for all RCC works from foundation to roof level

Steel reinforcement of grade Fe-500D or more for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete fo all levels

Structural steel work in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete welded

P/F of 16 mm dia holding down anchor bolts 450 mm long along with nuts for holding of steel trusses / frames in roof of the building.

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead upto 50 m and lift upto 1.5 m.

Providing and fixing in position Stainless steel Grade 304 plate as per design for expansion joints including necessary grooves, screw arrangement and desired shape etc

2mm 200mm wide

1mm 300 mm wide

Providing and fixing white vitreous china pedestal type water closet(Eur opean type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including connection pipes ,cutting and making good the walls and floors wherever required with W.C. pan with ISI marked black solid plastic seat and lid

Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge.

Providing and fixing wash basin with pedestals, C.I. brackets, 15 mm dia CP Brass single hole basin mixer of approved quality and make, including connection pipes , cp waste ,painting of fittings and brackets, cutting and making good the walls wherever required:-White Vitreous China Wash basin size 550x400 mm with a 15 mm CP Brass single hole basin mixer

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste flexible pipe

Providing and fixing 15 mm nominal bore CP brass double lever basin mixer of approved quality and make as approved by Engineer - in - charge.

Providing and fixing 15 mm nominal bore CP brass double lever wall mixer of approved quality and make as approved by Engineer - in - charge.

Providing and fixing Stainless Steel A ISI 304 (18/8) Kitchen sink without drain board of size 610x460 mm bowl depth 200 mm as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including cp waste and pipe connections, painting of fittings and brackets, cutting and making good the walls wherever required

Providing and fixing 15 mm nominal bore CP brass double lever sink mixer of approved quality and make as approved by Engineer - in - charge.

Providing and fixing 50 ltr capacity hot water Geysers of standard make including connection pipes etc, all complete

Providing and fixing CP grating nominal 100mm size

Providing and fixing PTMT liquid soap container 109 mm wide, 125mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour

Providing and fixing PTMT towel ring trapezoidal shape 215 mm long,200 mm wide with minimum distances of 37 mm from wall face with concealed fittings arrangement of approved quality and colour

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 :15 mm nominal bore

Providing and fixing C.P. brass angle valve for basin mixer and geyser points etc of approved quality conforming to IS:8931 of 15 mm nominal bore

Providing and fixing C.P. Brass extension nipple (size 15mmx50mm) of approved make and quality as per direction of Engineer-in-charge.

Demolishing cement concrete manually/by mechanical means including disposal of material within 50 meters lead as per direction of Engineer-incharge:

Dismantling steel work manually/by mechanical means in built up sections without dismembering and stacking within 50 meters lead as pe rdirection of Engineer-in-charge:

Dismantling roofing including ridges, hips valleys and gutters etc., and stacking the material within 50 meters lead GI sheet

Dismantling chain link fencing