PROVISION OF LADIES AND GENTS TOILET NEAR ALS SIMULATOR HALL AND CERTAIN PROVISION WORK AT BRICHGUNJ MILITARY STATION UNDER GE BRICHGUNJ, SRI VIJAYA PURAM

Amount

Excavation in trenches, not exceeding 1.5m wide and not exceeding 1.5m in depth for foundation, etc or not exceeding 10 Sqm on plan for shafts, cesspits, manholes, pier holes, etc and getting out in soft/loose soil complete all as specified and directed.

M & L for Plain cement concrete 1:4:8 type D2 using 40mm graded stone aggregate as in foundation filling complete all as specified and directed.

M&L for Precast Cement Concrete Block Masonry with Solid Block, exc 10cm in width in type C-1, 1:3:6 (using 20mm graded stone aggregate) set in CM (1:6) complete all as specified and directed.

M & L for RCC- M - 30 Design Mix as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and directed.

M & L for RCC- M -30 Design Mix as in columns, pillars, piers,posts and struts complete all as specified and directed.

M & L for RCC- M -30 Design Mix as in beams, cantilevers,bressummers, lintels over 1.5m span complete all as specified and directed.

M & L for RCC- M -30 Design Mix as in slabs supported on walls,beams and columns in floors, roofs, landings, balconies , canopies, deck slabs and in,shelves and the like complete all as specified and directed.

Use & waste of Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter for fair finished surfaces of concrete complete all as specified and directed.

Use & waste of Form work to sides of square or rectangular columns, pillars, posts and struts for fair finished surfaces of concrete complete all as specified and directed.

Use & waste of Form work to sides & soffits of lintels over 1.5m clear span, floor or roof beams, cantilevers, etc for fair finished flat surfaces of concrete complete all as specified and directed.

Use & waste of Form work to slabs including edges for fair finished flat surfaces of concrete complete all as specified and directed.

S&F Mild steel TMT bars 10mm dia and over as reinforcement for concrete, cut to length, bent to shape required, including cranking, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed.

S&F Mild steel TMT bars 6 to 8mm dia as reinforcement for concrete, cut to length, bent to shape required, including cranking, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed.

S&F Mild steel TMT bars 5 to 10mm dia in stirrups, spacers and binders, cut to length, bent to shape required, including cranking, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed.

M&L Rendering 10mm thick on concrete surfaces in CM (1:6) finished even & smooth without using extra cement complete all as specified and directed.

M & L for rendering 5 mm thick in CM I:3 on for ceiling surfaces, finished even and smooth without using extra cement etc complete all as specified and directed.

M&L for rendering 15mm thick in two coats on faces of brick work or concrete surfaces; first coat (rendering coat) of 10 mm thick in cement mortar 1: 6 and second coat (finishing coat) of 5 mm thick in cement mortar 1: 4 mixed with water proofing compound and finished even and smooth complete all as specified and directed. Note: water proofing compound shall be measured and paid separately as supply only)

Supply only water proofing compound.

M&L preparation of newly plastered surfaces of wall and applying two coats of Oil Bound distemper over a coat of primer over a coat of internal wall care putty complete all as specified and directed.

M&L preparation of newly plastered Ceiling surfaces and applying two coats of Oil Bound distemper over a coat of primer over a coat of internal wall care putty complete all as specified and directed.

M& L for Finishing new walls with Acrylic smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) etc complete all as specified and as directed.

M & L for water proofing treatment with the following specifications including taking down existing roof treatment of any description and cleaning with water and scrubbing and disposing off the rubbish outside the premises, complete all as specified and as per manufacturers instructions:- (i) Screed Bed 10mm thick in CM 1:4 on concrete surfaces mixed with water proofing compound @ 3% by weight of cement as leveling course (ii) Apply a coat of hot blown bitumen 85/25 @ 1.20 kg/sqm over a coat of bituminous primer @ 0.3 ltr per sqm. (iii) Laying APP membrane (STP Aquashield or equivalent) weighing not less than 3.5 Kg/sqm, reinforced with polyster non woven fabric (weighing not less than 150 gms/sqm) with 100mm over laps both longitudinally and transversally and overlaps shall be sealed by torch, membrane shall be taken to the parapet through fillet and shall be tucked in inside after a height of 300 mm. (iv) Apply one coat of hot blown bitumen 85/25 @ 1.2 kg/sqm over the membrane. Note :- Water proofing compound shall be measured and paid separately as supply only.

Returning, filling in excavated approved soil, including spreading, levelling, watering and well ramming in layers not exceeding 25cm each complete all as specified and directed.

Spreading and leveling excavated approved soil in layers not exceeding 25cm thick including watering and well ramming complete all as specified and directed.

Removing excavated soil to a distance not exceeding 50m and depositing where directed. at a level not exceeding 1.5m above the starting point complete all as specified and directed.

Surface excavation not exceeding 30cm deep and averaging 15cm deep and getting out in soft/loose soil complete all as specified and directed.

M&L for PCC 1:4:8 type D-2 using 40 mm graded stone aggregate in 100mm thick as in sub base complete all as specified and directed.

M&L for hard core of broken stone or boulders of gauge not exceeding 63mm, deposited, spread and levelled in layers not exceeding 15cm thick, watered and rammed to a true surface complete all as specified and directed.

M&L for PCC 1:3:6 type C1 using 20mm graded aggregate of 75mm thick as in Plinth Protection complete all as specified and directed.

M&L coloured chequered finish endura tiles 10-12 mm thick (square /rectangular) textured series area of each tile exceeding 0.07 sqm not exceeding 0.18 sqm as in floors, treads and risers of steps fixed with white cement and pigment complete all as per manufacturer instructions as directed.

M&L Vitrified tiles 10 mm thick (square/ rectangular) any shade polished, area of each tiles not exceeding 0.36sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including screed bed or bedding layer of mortar 15 mm thick in Cement mortor 1:4 for laying floor finishes complete all as specified and directed.

M&L Vitrified tiles 10 mm thick (square/ rectangular) any shade polished, area of each tiles exceeding 0.42sqm and not exceeding 1.00sqm, in wall surfaces(skirting/daddo) set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including backing coat of 10 mm thick in Cement mortor 1:4 complete all as specified and directed.

S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately).

S&F factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction. (Note: stainless steel butt hinges and necessary S.S screws shall be paid separately)

S&F 100 Butt hinges extruded aluminium alloy, anodised. With galvanished mild steel hinge pin , anodised and fixed type B-21 complete all as specified and directed.

S&F 200mm Aluminium anodised barrel tower bolts of extruded sections complete all as specified and directed.

S&F 150mm Extruded aluminium alloy handles, fabricated type, anodised complete all as specified and directed.

S & F aluminium alloy, anodised, sliding door bolt with hasp & staple (Bolt type) 250mm long and fixing clips of sheet, cast or extruded section and fixing bolt of cast aluminium alloy, complete all as specified and directed.

Supply only 4.0mm thick sheet glass, ordinary quality in squares n exc 0.50 sq.m in each pane complete all as specified and directed.

S&F aluminium alloy wire mesh 0.45mm nominal dia of wire and average width of apeture 1.4mm fixed with aluminium wire staples etc.complete all as specified and as directed

S & F Powder coated aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and directed.

Supply and fix aluminium composite panel sheet of 3 to 4 mm thick as in wall cladding & false ceiling, including aluminium frame work with plastic strips ( double sided sticker) of suitable size of varying thickness of 10mm to 30 mm , applying adhesive over aluminium sections for fixing composite panel and fixed with screws. The joints of panels shall be filled with weather proof sealant, The board shall be stuck with a layer of any colour high intensity reflective grade polymer sticker installed using epoxy adhesive complete all as specified and as directed.

M&L for 18-20mm thick Granite of any type work table rubbed and polished in steps, jambs , pillars, cooking platforms and the like including pointing with white cement 1:2 using marble dust with admixture of pigment to match with shade of granite complete all as specified and as directed.

M&L for 18-20mm thick Granite (of any type) work (table rubbed and polished) for wall lining (veneering to wall) 12mm thick in cement mortar (1:3) and pointing with white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and as directed.

Supplying and laying of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified of dia 20 mm complete all as specified and directed.

Supplying and laying of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified of dia 25 mm complete all as specified and directed.

Supplying and laying of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified of dia 40 mm complete all as specified and directed.

S&F 75mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints,fixed to walls complete all as specified and directed.

S&F 75mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints,laid in floor complete all as specified and directed.

S&F PVC (SWR) Gully trap 125/110 mm,setting and incl joining with solvent cement complete all as specified and directed.

S&F 110mm PVC (SWR) WC connector bent type setting including Joining with solvent cement complete all as specified and directed.

S&F 110mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall complete all as specified and directed.

S&F 110mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints,laid in floors complete all as specified and directed.

S&F 75mm dia PVC (SWR) bend complete all as specified and as directed

S&F 110mm dia PVC (SWR) bend complete all as specified and as directed

S&F 75mm bore PVC (SWR) junction single, (Single T) equal or unequal complete all as specified and as directed

S&F 110 mm bore PVC (SWR) junction single, (Single T) equal or unequal complete all as specified and as directed

S&F Stack clamps out of 50 mm by 5 mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof for 75 mm dia pipe complete all as specified and as directed

S&F Stack clamps out of 50 mm by 5 mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof for 100 mm dia pipe complete all as specified and as directed

S&F PVC (SWR) cowls 100 mm dia complete all as specified and as directed.

S&F Gun Metal Gate valves 40 mm dia with iron wheel head screwed both ends for iron pipes complete all as specified and directed.

S & F 1000 litres capacity Rotational moulded polythene water storage tanks(cylindrical vertical with closed top) hoisted in position incl 20 mm dia brass float valve complete all as specified and directed.

S&F 15mm Bore Stop Valves / Angle Cock Fancy Type Chromium plated cast copper alloy screwed down high pressure with crutch or butterfly handles screwed both ends complete all as specified and directed.

S&F Vitreous China Wash down water closet pan pedastel pattern (EWC) white in colour with and incl plastic water seat and cover white closed pattern with flat bottom and cover and MS chromium plated hinging device incl connection to outgoing pipe and flushing pipewith connecting Assoceries complete all as specified and directed.

S&F PVC low level flushing cistern 10 litres capacity with inlet ball valve, float and handles including brackets complete all as specified and directed.

S&F Bib cock, 2 way double handle with flange, cast copper alloy, chromium plated with crutch or butterfly handle, fancy type of approved make and Cat No., screwed down, screwed for iron pipe or for brass ferrule 15mm bore complete all as specified and directed

S&F hand shower (health faucet) with 8mm dia 1.0 meter long, chromium plated flexible tube and wall hook complete all as specified and directed.

S&F looking mirror Bevelled Edge 600mmx450mm mounted on 6mm thick AC building board or commercial ply wood and fixed to wooden plugs with chromium plated brass screws and cup washers complete all as specified and directed.

S&F Chromium Plated Steel Grating of 100mm size complete all as specified and directed.

S&F Bib tap cast copper alloy chromium plated 15mm dia with fancy type screwed down screwed for iron pipe or brass ferule etc complete all as specified and directed.

S&F vitreous china white thin Rim table top basin of size 500x380x120mm with and including 20 mm dia fancy type CP long body pillar tap & 32mm waste coupling brass chromium plated suitable for wash hand basins of approved make and Cat No. complete all as specified and directed.

S&F 32mm bore brass CP bottle trap for wash basins with inlet and outlet screwed for pipe or connections including necessary packing, union and cap complete all as specified and directed

S&F Vitreous china bowl urinal flat back of size 355 x 340 x 535 mm , white, with grating and union for discharge pipe including connections to flush pipe and outgoing pipes, complete all as specified and directed.

S&F PVC flexible connections 15 mm dia 450 mm long with brass checknuts .

Excavation over areas, not exceeding 1.5m deep and getting out in hard dense soil complete all as specified and directed.

Excavation over area, exceeding 1.5m but not exceeding 3m deep and getting out in hard dense soil complete all as specified and directed.

Excavation in trenches, not exceeding 1.5m wide and not exceeding 1.5m in depth for foundation, etc or not exceeding 10 Sqm on plan for shafts, cesspits, manholes, pier holes, etc and getting out in hard dense soil complete all as specified and directed.

M&L for precast man holes cover slab with 1:2:4 type B1 using 20mm graded stone aggregate set in CM 1:4 incl cost of use and waste of clean sawn wooden form work but excl cost of reinforcement complete all as specified and directed.

M&L for 80 mm thick PCC (1:2:4), B1 using 20 mm graded stone aggregate as in floors finished even and smooth without using extra cement complete all as specified and directed.

Use & waste formwork to rough finished concrete surfaces of walls,retaining walls, abutments,parapets and staircase railings and similar work incl attached pillasters buttresses etc vertical or to batter complete all as specified and directed.

M & L for RCC M-30 design mix concrete (using 20 mm graded stone aggretate) as in retaining walls and the like any thickness above top of footing including attached pillasters and butteresses complete all as specified and directed.

M&L Rendering 15mm thick on concrete surfaces in CM (1:4) finished even & smooth without using extra cement complete all as specified and directed. .(Note : WPC shall be measured and paid separately)

M & L PCC 1:2:4 type B1 (using 20 mm graded agg.) as in benching, like works, hold fast block incl. necessary form work complete all as specified and directed.

M&L for PCC (1:3:6), C2 using 40 mm graded stone aggregate as in foundations, filling and mass concrete all as specified & directed.

M&L PCC 1:2:4 type B1 using 20mm graded stone aggregate as in surface channel / benching incl centre channel half round or 1/4 section incl cost of use and waste of clean sawn wooden form work complete all as specified and directed.

Extra for forming fair finished drain or channel 30cm inner girth in cement concrete, using extra cement, including forms, moulds, mi-ted/stoped ends etc complete all as specified and directed.

M&L for Concrete bed to drain pipes including packing under, and completely surrounding pipes with concrete after they are laid and tested in cement conrete 1:3:6 type C-2 around 150mm dia complete all as specified and directed.

M&L for 150mm bore CI pipes with spigot and socket ends centrifugally cast class LA in any length laid in trenches complete all as specified and directed.

M & L for point wiring complete with single core multi stranded Copper conductor FRLS cable of size 1.5 sqmm PVC insulated unsheathed 1100 volt grade in and including cocealed PVC conduit suitable size including Tee junction bends etc concealed in wall/fixed on ceiling and PVC switch board hylam sheet of 3mm thick including M.S. sunken boards of suitable size for housing switched sockets etc including 1.5 sqmm. green PVC insulated wire for earth continuty. complete all as specified and directed. (a) One light point/Exhaust fan controlled by one way switch

Supply and fix of switch piano flush type single pole one way 5 Amp complete all as specified and directed.

Supply and fix ceiling rose surface baklite 65 x 50 mm 3 terminal, complete all as specified and directed.

Supply and fix aluminium housing LED batten 20 watt fitting 4ft in length nano diffuser technology to ensure minimum loss in light transmitted, long life of over 30000 hours including lamp and connecting with twin core shethed cable from fitting to ceiling rose complete all as specified and directed.

S&F Street light New genration energy saving & envoirmental friendly long life versatile pressure dia cast aluminium IP65 road way luminaire with high power LEDs 36 w as light and electronic driver complete all as per with necessary brackets (made out of 25 mm bore GI light grade pipe approx. 0.6 M long) nuts, bolts etc to be fixed as on walls complete all as specified and directed.

Supply and fixing aluminum housing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.

Supply and fix exhaust fan suitable for on working of AC 230 V ,50 Hz 300 mm sweep 1400 RPM,with heavy duty motor ,incl louvers complete all as specified and directed.

Supply and fix metal enclosure distribution board SPN, 4 way 240 volts, with 100 amps rated bus bar, with IP 42 protection and double door, suitable for mounting MCBs complete all as specified and directed.

Supply and fix MCB single pole, 240 volts, 5 to 32 Amps, complete all as specified and directed.

Supply and fix MCB SPN 240 volts, 5 to 32 Amps, complete all as specified and directed.

M&L for earthing complete with galvanised steel earth plate electrode 60 x 60 cm x 6 mm thick buried directly in ground ( earth pit not less than 2.25 M deep below ground level) with top edge of the plate not less than 1.5 Meter below normal ground level connected to GI wire 4 mm dia by means of bolts, nuts , check nuts and washers of GI and GI tubing 20 mm bore light grade for earth lead protection up to main earth test point and including concrete pit in PCC (1:3:6) type C1 pre cast RCC (1:2:4) type B1 cover slab 54 x 54 x 5 cm with one handle for lifting made out of 8 mm dia MS bar, wire mesh, 20 mm bore GI tubing (LG) for watering, charcoal or coal and salt in alternate layers including excavation earth work complete all as specified and directed electrical plate No. 3 of SSR part - I

M & L for PCC 1:2:4, type B-1, (using 20 mm graded stone aggregate) for foundation and coping including necessary use & waste of form work complete all as specified and directed.

Supply and fixing of 2.4 metre decorative pole with single arm decorative bracket, made out of aluminium die cast high quality with profile design, adequate base plate at bottom conforming to its stability. Suitable designer bracket made out of aluminium casting with B-22 holder for fixing lamp. Pole and bracket should be powder coated, including supply and fixing of Decorative luminaire of 60W with colour temp of 2500-3000K suitable for fixing with above pole etc complete all as specified and as directed. Note-: (a) The design of pole, bracket and designer LED fitting shall got approved from GE before placing the purchase order. (b) PCC foundation shall be measured and paid seperately under respective item of this sch. (c) Prewired with suitable guage of wire from LED fitting to junction box shall deemed to be included in quoted rate.

Supply and lay HDPE double wall corrugated pipes confirming to IS-14930 Part II for cable protection of size 50mm OD and 38mm ID including all acessories such as bend, end caps and couplers etc,, complete incl taking down old DWC pipes complete all as specified and directed.

Supply & Lay XLPE insulated, heavy duty 1100 volt grade electric armoured LT UG cable with aluminium conductor of size 10 Sqmm 2 Core laid in trenches/along the wall/including making all connections, saddles, spacers complete with aluminium lugs as required at site complete all as specified and directed.

Supply and fix 25 mm bore GI tubing medium grade laid in trenches / floor or fixed to wall in any length with screwed and socket joints together with all galvanised GI fitting such as sockets, bends, elbows, tees, reducers, unions, jointing materials etc and pressure testing, washing out complete all as specified and directed

Supply and fix 25 mm dia ball valves high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed, complete all as specified and as directed

M&L for cutting existing 40/50mm GI line and making branch connection of 40 mm dia GI line and insert T complete all as specified and directed

Supply and fix 25 mm bore Gun Metal gate valve with iron wheel head ISI Marked screwed both ends suitable for GI tubing complete all as specifed and directed

Supply and fix 50 mm bore Gun Metal gate valve with iron wheel head ISI Marked screwed both ends suitable for GI tubing complete all as specifed and directed

ICON AGENCIES (BID ID -3304100)

M/s Pooja Enterprises (BID ID -3304005)

KAPOOR AUTOMOBILES (BID ID -3304279)

PSS ELECTRICAL WORKS (BID ID -3304088)