SPECIAL REPAIR TO BLDG NO T 106 DET/CORPS AND PROVN OF ONE TOILET AND TWO SETS OF URINALS NEAR BLDG NO NP 21 AND PARKING SHED HARD STANDING AND GUARD ROOM WITH WASH ROOM AND TOILET BLOCK NO T 43 EME BN AND CERTAIN MINOR WORK AT MIL STN JAMMU UNDER GE

Amount

Dismantling timber scantlings 40 Sq. cm and over in section, in any position (framed work ) complete all as specified.

Dismantling timber scantlings in fillets, rails, posts, rafters, purlins, etc. under 40 sq. cm in section.(unframed work) complete all as specified.

M&L and fabriaction of Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. conforming to Fe-410-W Gde E-250 quality A, complete all as specified and as directed by Engineer-in-charge

M&L and fabrication of framed brackets of angles or tees with web and flanges cut to shape, drilled and counter sunk for screw, including bending and welding angles, as necessary, gusset plates, riveting, etc, conforming to Fe.290.Gde-E-165

Dismantiling of asbestos cement (corrugated, semi corrugated, etc.) sheets in roof coverings complete all as specified.

S&F Pre- painted galvalume aluminum zinc coating (AZ-150 Micron) GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified complete all as specified.

S&F Pre-painted galvalume aluminum zinc coating (AZ-150 Micron) GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified complete all as specified.

Dismantling of ceiling board (Fibre, pulp, any type of insulation etc) or insulation board / slabs/any thickness including cover fillets and snap grids complete all as specified and directed

Providing and fixing false ceiling at all heights with GRG (Glass fibre Reinforced Gypsum) false ceiling tiles of Size 595x595mm of approved texture, with fully perforated 12 mm thick micro tegular edges, design and patterns having moisture content less than 2%, humidity resistance of 99%, NRC 0.50 to 0.75 as per BS 476 (Part -4)-1970 and light reflactance of 85% (Minimum) to be laid in true horizontal level suspended on interlocking metal T-Grid of hot dipped galvanized iron section of 0.33 mm thick (Galvanized @120 grams per Sqm incl both sides) comprising of Main T runners of Size 15x32 mm of length 3000mm, cross T of Size 15x32 mm of length 600 mm to form grid module of size 600x600 mm, suspended from ceiling galvanized mild steel items (Galvanizing @ 80 grams per Sqm) i.e., 50 mm long, 8 mm outer dia meter M-6 dash fasteners, 6 mm dia fully threaded hanger rod up to 1000 mtr length and L-shape level adjuster of Size 85x25x2 mm Galvanised iron perimeter wall angle of size 24x24x0.40 mm of length 3000 mm to be fixed on periphery wall/partition with the help of plastic rawl plugs at 450 mm centre to centre and 40 mm long dry wall screws. The work shall be carried out as per specifications, drawing and as per directions of Engr-in-Charge.

Demolition of brick work built in cement mortar including all quoin, arches pillars but excluding ashlar facing dressed stone work and precast concrete article complete all as directed.

Taking down cement plaster on brick or stone walls or stone walls etc, including raking out joints, hacking for key, scrubbing down with water, etc.

M&L Brick work with subclass 'B' bricks, old size bricks, straight or curved on plan exceeding 6 metre mean radius built in cement mortar 1:6 complete all as specified.

M&L Brick work with subclass 'B' bricks, old size bricks, straight or curved on plan exceeding 6 metre mean radius built in cement mortar 1:6 but except bricks complete all as specified.

M&L Brick work with subclass 'B' bricks, old size bricks, straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4 complete all as specified.

Material and labour for rendering 15 m thick on fair faces of brick or concrete surface walls, in cement mortar 1:4, rendering is to be finished even and smooth without using extra cement complete all as specified.

Material and labour rendering 15 m thick on other than fair faces of brick or concrete surface walls, in cement mortar 1:6, rendering is to be finished even and smooth without using extra cement complete all as specified.

Taking down chowkats or frames (without taking down shutter from the frame) not exceeding 1.5 Sqm each complete all as specified.

Taking down chowkhats or frames (without taking off shutters from the frame) exceeding 1.5 sqm but not exceeding 4 sqm each and removing from site complete all as specified.

Refixing of chowkats or frames(without taking off shutters from the frame) exc 1.50 Sqm and n exc 4.00 Sqm of wooden doors/aluminium doors & partition carefully refixing on the same opening incl minor repair all as specifed and as directed by Engr-in-Charge.

Material & labour factory made steel windows double shutter box type, outer frame made out of ERW TUBE 'P' section(60x35x25mm) and shutters of ERW TUBE 'P' section (50x35x20mm) openable shutters side hung includding pistol hinges with two Nos of MS Tower bolts 150mm size on each shutter steel handle and stopper of 'Z' section as specified complete with sash bars devetailed or welded ready for glass fixing and wire gauzed fixing with suitabel fittings/openning for cooler/AC where required .Steel windows will be double shutter external glazed and internal wire gauzed complete all as specifed and as per Drg No CEPZ/C-TD/27/13 of sheet No1/4 to 4/4 all as specified and directed by Engr-in-Charge. NOTE: The quoted rate against the above item shall also include (i) for Provn of one shop coat of zinc chromate primer on all exposed steel surfaces and one coat of coal tar on the ends of steel frame in contact with brick/conc surface (ii) 04 Nos MS Steel lugs of 20x5mm MS flat 20cm long over all welded to frames (iii) PCC block for embedding lugs.(iv) Provn of 10 mm square bar as guard bar, spacing 100 mm c/c all as per drg and incl 4 mm thick flat iron for for fixing of guard bars all around all as specified and as directed.

Supply and fixing galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with stainless steel wire staples, or galvanised wire staples complete all as specified.

Supply and fixing sheet glass ordinary quality 4mm thick and glazed with oil putty or any types of beads in square n.exc 0.5 Sqm each pane in any type of frame of Iron/ Steel/ Wood/ aluminium as required at site complete all as specified.

Supply and fixing 4 mm thick figured glass, pin head/frosted type and glazing with oil putty in square n.exc 0.5 sqm in each pane complete all as specified.

S&F pressed steel frames of size 125mm x 60mm made out of size 1.25mm thick MS sheet for doors double rebated including mild steel hinges medium weight 100 mm long and 25mm x 3mm flat iron in hold fast, tie bar including necessary fixing lugs, hold fast, lock strike plate and fixing arrangement etc complete as specified and making good in cement mortar 1:3 or cement concrete 1:2:4 type B-1 including PCC 1:3:6 as in back fill to chowkats all as specified.

Supply and fixing, plain framed, panelled shutter (two panel) 35mm thick, 2nd class hardwood with lock rail and panel of 9mm B.W.P commercial ply. The size of rail and stiles as per as per IS:1003 (Part-I), kiln seasoned and chemically pressure treated complete all as directed by Engr-in-Charge.

Supply and fixing 35mm thick 2nd Class hard wood glazed, gauzed and skelton shutters open rebated and prepare to receive glass, gauge etc but divided into squares with plain chamfered or rounded mitred and rebated sash bars, stiles and rails as specified in SSR Part-I Sec 8 clause 8.24 (a) complete all as specified.

S&F Solid PVC door frame of size 50mm x 47mm made out of 5mm Plain colour PVC sheet reinforced with mild steel square tube, supplying and fixing in opening as per specifications and drawing including making good to disturbed surface of walls, complete all as specified and as directed by Engr-in-Charge.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails MS frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying and fixing in the frame at site as per specification & drawing complete all as directed by Engr-in-Charge.

S&F butt hinges of mild steel cold rolled medium weight of size 125 mm as specified.

S&F aluminium anodised, barrel tower bolts size 150 mm of extruded section and fixed complete all as specified. (ISI Marked)

S&F aluminium handles, fabricated type, anodised size 100mm, anodised section and fixed complete all as specified. (ISI Marked)

S&F aluminium alloy, anodised, sliding door bolt size 250 mm with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified.

S&F aluminium hanging floor door stopper, twin rubber stopper, size 100mm, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete.

Supply and fixing mild steel helical ordinary rat tail rod pattern springs 300mm including roller and roller plate complete including fixing to pressed steel frames necessary welding work all as specified and as directed.

S&F ball/magnatic catches with 8mm dia steel ball, and brass body and striking plate including letting in and fixed all as specified and as directed by Engr -in-Charge.

M&L for applying two coat of synthetic enamel paint over a coat of red oxide primer on new steel surfaces of any description having width/girth exceeding 10 cm including preparation and rubbing with sand paper to make surface even and smooth complete all as specified

Preparation of old treated steel surfaces of any description not otherwise described, over 10 cm in width or girth and applying two coats of synthetic enamel paint all as specified and as directed.

M&L for preparation of old decorated concrete/ plastered surfaces of walls, Pillars, cornices etc by booming down with steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots & rubbing with sand paper and applying two coat of oil bound distemper on old decorated wall surface including two coats of wall care putty of 1 to 2 mm thick on uneven surface as and where required.

M&L for applying two coat of synthetic enamel paint on new wooden surfaces of any description over a coat of pink primer having width/girth exceeding 10 cm complete all as specified including preparation and necessary filling by chalk putty as and where requered to make surface even and smooth.

Material and labour for preparation of newly plastered surfaces of walls & applying two coats of oil bound distemper over two coat of wall care putty of 1 to 2 mm thick and one coat of primer complete all as specified.

Preparation of new plastered/ concrete surfaces of walls to achieve smooth and even surface and applying two coats of cement base paint over and including one coat of primer complete all as specified.

Preparation of old plastered surfaces of wall and applying two coats of cement base paint complete all as specified.

Demolition of cement concrete (unreinforced) ground floor to 4th floors and pavings n. exc 15 cm thickness (below or above ground level) and removing the rubbish from the work site out side defence premises complete all as specified.

M&L for cement concrete type D-2, (1:4:8) 75 mm thick as in sub base all as specified and as directed.

Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified.

Dismantling floor, hearth or wall tiling including cement mortar bedding, terrazo dado from wall surface (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specied and directed.

M&L for 25 mm thick cement concrete 1:2:4, type B-0, (using 12.5 mm graded crushed stone aggregate) as in sub base/ levelling course of floors, finished even and fair complete all as specified and directed.

Dismantling stone slabs and tiles of any description or thickness in floor ars laid bedded and pointed in any morter, aprons etc all as specified and as directed.

Material and labour glazed ceramic coloured digital tiles in vertical surface 300x450x7 mm thick, set and jointed in neat cement slurry and pointed white or colored cement to match the surface over and including 10 mm thick CM 1:4 all as specified. (Sample as approved & Kept in GE's sample room)

Material and labour Non-skid Digital Ceramic joint less coloured tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match and set in neat cement slurry and pointed with coloured/white cement to match the surface over and including 15 mm thick screed bed in CM 1:4. (sample as approved GE & kept in sample room)

Material and labour for Vitrified Ceramic (Double Charged) edge cut joint free coloured or printed any shade tiles 10 mm thick (square/ rectangular) polished area of each tiles exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match and set in neat cement slurry and pointed with coloured/white cement to match over and including 15mm thick screed bed in CM 1:4 and tiles to be laid with spacer between tiles and gaps are to be filled with PU grout complete all as specified and as directed. (Sample as approved & Kept in GE's sample room)

Ditto all as item No 51 but as in vertical surfaces dado/skirting over a backing coat of CM 1:4, 10 mm thick complete.

M&L 16 to 18 mm thick Granite (Z-Black) (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite, over 15 mm thick CM 1:4 as directed by Engr-in-charge.

Supply and fixing sinks made of stainless steel 1.00 mm thick kitchen or laboratory with plugs, washers and wastes including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 610mm x 460mm bowl size 560mm x 410mm x 200mm complete with CP waste coupling & PVC waste pipe complete all as specified and directed by Engineer-in-charge.

S&F in repair vitreous china, wash basin white, counter top, size 630x450 mm, including cutting for and pinning in ends of brackets or erecting stand including fixing and supply of waste pipe of 32 mm dia, waste coupling of chromium plated brass complete all as specified and as directed by Engineer-in-charge.

S&F in repair Single piece-WC with UF soft close seat cover, hinges, fixing accessories set and accessories set, cistern fittings, size: 660 x 365 x 765mm, S Trap-300mm complete all as specified.

S&F in repair PVC valveless, syphonic action type, flushing cistern, low level, white with inlet, ball valve, float and handle including brackets, PVC 32 mm 'L' bend of capacity 10 litres and making good to dismantled/damaged floor/surfaces, complete all as specified and as directed by Engineer-in-charge.

S&F in repairs Vitreous China urinals, half stall (back or corner wall type), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement, CP spreader, coupling grating and Union for discharge pipe all as specified and as directed.

S&F in repairs long body Bib Cock with wall flange cast copper alloy, chromium plated fancy type, complete all as specified.

S&F in repairs 15mm bore CP mixer Pillar taps long body (suitable for table top/counter top WHB), cast copper alloy, with capstan heads, chromium plated, fancy type, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified.

Supply and fixing in repair wall mixer non telephonic shower arrangement with connecting legs and wall flanges, cast copper alloy, chromium plated, complete all as specified.

Supply and fixing in repair Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified.

S&F in repair tubular towel rail, 20mm dia, D type, 60cm long between flanges complete all as specified.

S&F in repair stainless steel soap dish holder complete all as specified.

S&F in repair sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified.

S&F stop valves 15mm, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified.

S&F Gun-metal, globe or gate valves, 20mm with iron wheel head, screwed both ends for iron pipe and fixed all as specified and as directed.

Supply and fixing tubes 'medium grade' galvanised, 15 mm bore, ISI marked with all fitting such as bends, tees, elbows, unions, short pieces, connectors, back nuts etc and fixed complete to walls and ceilings or laid in floors, complete all as specified and as directed by Engineer-in-charge.

Supply and fixing tubes 'medium grade' galvanised, 20 mm bore, ISI marked with all fitting such as bends, tees, elbows, unions, short pieces, connectors, back nuts etc and fixed complete to walls and ceilings or laid in floors, complete all as specified and as directed by Engineer-in-charge.

S&F in repair PVC connection 15mmx600mm including brass check nut at both ends screwed for iron pipe of 15 mm bore.

Supply and fixing UPVC (SWR) type B pipes 110 mm bore single socketed, in any length with rubber ring joints fixed to walls including stack clamp of GI flat 30mm wide 2mm thick fixed to wall with nail at spacing of 1m center to center complete all as specified and as directed by Engineer-in-charge.

Supply and fixing UPVC (SWR) type B pipes 75 mm bore single socketed in any length with rubber ring joints, laid in trenches or in floors, complete all as specified and as directed by Engineer-in-charge.

Supply and fixing UPVC(SWR) type B pipes 75 mm bore single socketed, in any length with rubber ring joints fixed to walls including stack clamp of GI flat 30mm wide 2mm thick fixed to wall with nail at spacing of 1m center to center, complete all as specified and as directed by Engineer-in-charge.

Supply and fixing, UPVC (SWR), bends for 75 mm bore, complete all as specified and as directed by Engineer-in-charge.

Supply and fixing UPVC (SWR), bends with access door for 75 mm bore, complete all as specified and as directed by Engineer-in-charge.

Supply and fixing UPVC(SWR), bends for 110mm bore complete all as specified and as directed by Engineer-in-charge.

Supply and fixing, UPVC(SWR), bends with access door, for 110 mm bore complete all as specified and as directed by Engineer-in-charge.

Supply and fixing UPVC (SWR) floor trap plain with grating having dia meter of out let 75mm including jointing with solvent cement to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified and directed.

S&F in repair, UPVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement complete all as specified.

Demolition of reinforced cement concrete of any discription ground to 4th floors and removing the rubbish from the work site out side defence premises complete all as specified.

M&L for RCC M-15, nominal mix, type B-1(1:2:4), using 20mm graded crushed stone aggregate as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like, complete all as specified and directed.

M&L for use and waste form work to soffits of suspended slabs such as roof slabs, floor slabs landings and similar work, not exceeding 200mm thick (horizontal or sloping) for rough finished surfaces of concrete, complete all as specified and directed.

M&L for use and waste form work to edges of concrete flats, treads, break in floors, window cills, concrete railings, openings in concrete walls, floor and roof and not exc. 20cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc. 10cm but n.exc. 20cm wide for fair finished surfaces of concrete, complete all as specified & directed.

M&L for water proofing treatment in the following sequences:- (a) Applying 1st course of bituminous primer conforming to IS -3384 @ 0.4 Kg/Sqm cover the surface till the surface properly impregnated and insolvent oil primer evoporate completely. (b) Applying 2nd coat of blown 85/25 graded bitumen confirming to IS 702 @ 1.2 Kg/sqm. (c) Applying 3rd course of APP (Atactic Polypropylene) modified polymeric membrane 3 mm thick weight not less than 3.6 Kg/Sqm with 160 Grams/Sqm non woven polyester made at centre core reinforced laid with 75 mm side overlap and 100 mm overlap. The membrane has to be laid with LPG torch and overlap sealed and finished neat incl complete removal existing water proofing treatment of any description and in any layer taking doen cement plaster of any thickness and removal of debris complete all as specified and as directed.

M&L for P.C.C 1:2:4 type B-0 using 12.5 mm graded stone aggregate as in padding over roof finished and laid to required slope complete all as specified and as directed.

M&L Rendering 15mm thck in CM 1:4 on Concrete surfaces of roof finished fair & even and including mixing of water proofing compound (WPC shall be measured and paid separately)

M&L for preparation of newly sufrace of APP Membrane and applying two coats of water based bituminious alumunium paint @ 200 ml per sqm etc.

S&F for 6 mm thick 5 Nos of ply veneered decorative plywood, grade 1 (with BWR resin) with decorative face veneers on both faces fixed with brass screws/resins to timber frame work/walls as in cup board incl all exposed edges shall be covered with 0.05 mm thick edge band matching with the ply wood all as specified and as directed by Engr-in-Charge.

S&F for 9 mm thick 5 Nos of ply veneered decorative plywood, grade 1 (with BWR resin) with decorative face veneers on both faces fixed with brass screws/resins to timber frame work/walls as in cup board incl all exposed edges shall be covered with 0.05 mm thick edge band matching with the ply wood all as specified and as directed by Engr-in-Charge.

S&F for 16 mm thick 7 Nos of ply Veneered decorative plywood, grade 1 (with BWR resin) with decorative face veneers on both faces fixed with brass screws/resins to timber frame work/walls as in cup board incl all exposed edges shall be covered with 0.05 mm thick edge band matching with the ply wood all as specified and as directed by Engr -in Charge.

S&F soft closing adjustable auto hinges of size 150mm length fixed in cupboards with screws for holding stainless steel brackets complete all as specified and as directed.

S&F telescopic heavy duty drawer channels soft closer of size 450m length (In closed position) fixed in PVC ply with brass screws as in drawers complete all as specified and as directed.

Dismantling posts or struts (wood, steel or R.C.C.) any section from natural ground, including taking out embedded portion and making good disturbed ground all as speified.

Excavating in post holes (or similar holes) each n exc 0.5 cum, getting out, in soft/loose soil, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, all as specified and as directed.

M&L for cement concrete (1:3:6) type B-2 20 mm stone graded stone aggregate as in in walls or retaining walls, any thickness, size or shape including pilasters, buttresses columns, pillars, boundary pillars and posts (including caps and bases)foundation filling and mass concrete all as specified.

M&L for MS work such as angle iron fencing posts struts and flat iron fillets etc, including drilling hole punching, splitting ends to secure chain link fencing or fixing of barbed wire to posts including all necessary cutting, welding bolting or riveting etc complete all as specified and similar work conforming to Fe-290 Gde E-165.

Supply only chain link MS galvanised fencing of size 50mm x 50 mm cold dip complete all as specified.

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, angle iron frame and flat iron, rails, straining bolts, etc. complete all as specified. Note:- Angle iron, flat iron & nuts and bolts shall be measured and paid separately.

S&F in repair Galvanised, 2 strand, steel barbed wire 2.24 mm dia barbed with 2 mm dia barbs at 75 mm spacings and straining and fixing to any type of standard rails, straining bolts including securing or tying at crossing with and provision of galvanised mild steel wire, staples or steel pins etc. as directed (each line wire to be measured).

S & F in repairs Aluminum anodized powder coated frame of size 101.60 x 44.45 made out of 1.20mm thick aluminum section fixed to floor/wall with plugs and screws complete all as specified and directed

S&F in repairs Aluminum Power coated, sliding windows two track with mosquito proofing with style 44.4x44.5x2mm thick including 4.0 mm thick coloured/tinted/frosted glass panes including aluminium grill and incl necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.) hinges type B-21 100mm long (2 no.) suitable handle (1 no.) necessary fittings and fixtures and provn of AC opening as required complete all as per direction of Engr-in-charge.

Surface dressing n exc 15 cm deep and getting out in soft/loose soil all as specified.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits,manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out soft/loose dense soil all as specified.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm all as specified and as directed.

Removing excavated material exc. 250m and n exc 500 m and depositing where directed at a level n exc. 1.5 m above the starting point all as specified and as directed.

M&L for Cement concrete (1:4:8) type D-2 40 mm stone graded aggregate as in foundation filling and mass concrete all as specified.

M&L for RCC M-20 (Design Mix) as in foundations, including rafts,footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete all as specified and as directed.

M&L for RCC M-20 (Design Mix) as in column, pillars, piers and struts all as specified and as directed.

M&L for RCC M-20 (Design Mix) as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies,canopies, deck slabs and in shelves and the like all as specied and as specified.

M&L for Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of concrete foundation and plinth beams and similar work and as in fair finish all as specified.

M&L for Formwork to sides of pillars, posts, struts, piers, columns and stanchions and to be finish in rough all as specified.

M&L for TMT mild steel bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for column, hooking end and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips, complete all as specified and directed.

Ditto above items No 114 but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders all as specified.

M&L Rendering cement plaster, 5 mm thick on ceiling finished even and smooth in cement mortar 1:3 w/o using extra cement complete all as specified.

Supply and laying sand filling under floors or in foundations incl watering and consolidation all as specified.

Supply and laying Hard core of guage 63 mm broken stone or boulders deposited, spread and levelled in layers n exc 15 cm thick water and rammed to a true surface all as specified.

M&L for 75mm thick cement concrete 1:3:6, type C1, using 20mm graded crushed stone aggregate as in plinth protection, laid in slope of 1:20 and surface finished even and smooth without using extra cement including making joint at 3m interval and at each corner the joint shall be filled with bitumen mastic filling to full depth (comprising one part hot blown bitumen 85/25 and two part of sand), complete all as specified and directed.

M&L for PCC 1:2:4 type B 1 using (20 mm graded aggregate) as in blocks for hold fasts, benching, coping apex stones, bed plates and the like including weathering slightly rounded or chamfered angles and throating all as specified and direct. Note: Form work required for these items included in the unit rate of this item.

M&L Machine cut kota stone slab flooring 18-20 mm thick over and including cement screed bed laid and jointed cement screed bed laidand jointed with grey camant slurry mixed with pigment to match the shade of slab including rubbing and polishing complete for tread of staircase over and including 15mm thick screed bed in CM 1:6 all as specifid and directed

M&L Machine cut kota stone slab 15-18 mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing complete for risers of staircase over and including 10mm thick fair and even plaster in CM 1:4 after roughing surfaces of old concrete/any type of plaster by picking sweeping down with water to remove dust etc.

S&F in coloured Chequered cement concrete tiles 30cm x 30cm x 25mm thick, set, jointed and pointed in neat cement slurry in floors incl 15 mm thick screed bed (1:6) with white cement and pigments all as specified

S&F 150 mm dia Reinforced concrete pipes, class NP2, laid and jointed complete with collars all as specified and as directed.

Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-l smooth finished, and reforming benching as required all as specified and as directed.

Supply and fixing Vitreous china ware pedestal type water closet white, with 'P' or 'S' trap including self closing seat cover, closed pattern with flat bottom, complete all as directed.

Supply and fixing Vitreous china ware WC Orissa pattern white with integral foot rest 580x 440 mm including L bend & PCC bedding in 1:2:4 and including P/S trap and flush pipe compete all as specified.

S&F PVC valveless, syphonic action type, flushing cistern, low level, white with inlet, ball valve, float and handle including brackets, PVC 32 mm 'L' bend of capacity 10.0 litres complete all as specified and as directed by Engineer-in-charge.

S&F vitreous china urinals, bowl type (back or corner wall type), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement fixing automatic flushing cistern with brackets, flush pipe, grating and union for discharge pipe.all as specified and as directed.

S&F vitreous China, wash basin white, flat back , size 550mmx400 including brackets of any size, including cutting for and pinning in ends of brackets or erecting stand including fixing and supply of waste pipe of 32 mm dia, waste coupling of chromium plated brass complete all as specified and as directed by Engineer-in-charge.

S&F Bib Cock with wall flange cast copper alloy, chromium plated fancy type, complete all as specified.

S&F 15mm bore CP mixer Pillar taps long body (suitable for table top/counter top WHB), cast copper alloy, with capstan heads, chromium plated, fancy type, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified.

S&F Overhead Shower 125 mm dia round shape single flow with shower arm, complete all as specified.

S&F tubular towel rail, 20mm dia, D type, 60cm long between flanges complete all as specified.

S&F chromium urinal sprader complete all as specified complete.

S&F Corner Glass Shelf (with Bracket) as per directed by Engr-in-charge.

Supply and fixing Rotational moulded polyethylene water storage tanks of 1000 litres capacity, (cylindrical vertical with closed top) with plastic lid cover, triple layered, white, hoisted and fixed in position all as specified in SSR Part-I including PTMT Ball valves high pressure with epoxy coated Aluminium rod & high density plastic ball complete, screwed for iron pipe or brass ferrule and fixed for 20 mm bore pipe, including making connections complete all as specified.

Supply and fixing Rotational moulded polyethylene water storage tanks of 500 litres capacity, (cylindrical vertical with closed top) with plastic lid cover, triple layered, white, hoisted and fixed in position all as specified in SSR Part-I including PTMT Ball valves high pressure with epoxy coated Aluminium rod & high density plastic ball complete, screwed for iron pipe or brass ferrule and fixed for 20 mm bore pipe, including making connections complete all as specified.

M&L Flush shutters, 30 mm thick solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified. Note:- Sampel approved by Engr-in-Charge or GE.

S&F for Aluminum Powder coated aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips,rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) complete all as specified.

M&L for preparation of newly plastered surfaces and applying two coats of exterior emulsion paint incl 2 to 3 mm thick wall care putty over one of primer and preparation to receive distemper all as specified and as directed.

S&F and fabrication as in framed work, doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering,running rails and guides) and hanging; also fastening and fixing complete all as specified.

M&L for steel work in tubular trusses including special shaped washer etc complete using ERW or induction butt welded tubes conforming to I.S.1161-1979 grade St.-240 all as specified and as directed.

Taking down carefully aluminium conductor point wiring (light, fan, socket, power socket) complete fitting such as swithes, sockets, lamp holder, utility light fitting, fan regulator etc and removing materials from sites and making good distrubed surface of walls and roofs complete all as specified and as directed.

Taking down of unsv MCB DB SPN /TPN along with MCB's

Taking down of unsv Sub main wiring of any size

M & L for complete point wiring with 1.5 Sqmm single core multi stranded copper conductor FRLSH insulated and unsheathed heavy duty cable in colour code including contineous earth wire with cable of size 1.5 sqmm copper conductor flexible FRLSH insulated drawn in and including concealed PVC rigid conduit medium grade ISI marked after cutting chases in wall , plastering after concealing conduit , including modular galvanised flush boxes of suitable size and white cover plate with frame as per relevant IS for mounting modular switches, sockets, fan regulators etc complete all as specified and as directed for the following :- (a) One Light / Fan/ Exhaust Fan point controlled by one, one way switch 6 Amp complete

(b) One 3 pin socket outlet 6 amp independent

(c) One 3 pin socket outlet 6 amp same board

(d) One bell/ buzzer point controlled by one, complete all as specified and directed.

All as per srl item No 147 above but for one 3 pin socket outlet 16 Amp independent with cable of size 2.5 Sqmm for point wiring and 2.5 sqmm as in continuous earth wire.

Supply and fix modular type switch, one way 6 Amps, 1 module complete all as specified and directed.

Supply and fix modular type socket 5 pin, 6 Amps 2 module complete all as specified and directed.

Supply and fix modular type switch, one way 16 Amps, 1 module complete all as specified and directed.

Supply and fix modular type socket 5 pin, 6 A/16 Amps 2 module complete all as specified and directed.

Supply and fix modular type fan regulator step down 120 Watt, 2 module complete all as specified and directed.

Supply and fix ceiling rose surface, backelite, three terminal, 240 volts complete all as specified and directed.

Supply and fix modular bell push with indicator polycarbonate materials ISI markrd 1 module, 6 Amps 240 Volts.

Supply and fix musical door bell, AC 230 Volts single phase.

Supply and fix LED light fitting 1x18Watt, 220V, AC decorative box type with driver, holder including LED Tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete with all fixing arrengenment all as directed by Engr in chage.

Supply and fixing of recess mounting 2 x 2 LED luminarie, 36W deep drawn CRCA housing with high power LED premium white powder coated frame blends seamlessly with ceiling layout, suitable for 600x600mm modular ceiling grid and also can be suspended with provided kit, complete fitting with all fixing arrangement all as specified and directed by Engr-in-Charge.

Supply and fixing of LED track light COB luminaire 20 Watts with Single phase 1 mtr Tracks high efficacy Housing made of extructed aluminium Options availabe in various beam angles to suit varied applications in office and retail spaces and fixing in roof and wall by anchor fastner all as directed by Engr-in-charge.

Supply and fix of lamp holder, PVC /Polycarbonate type with back plate for batten fitting .

Supply and fix LED lamp suitable for B22 holder of capacity 10 Watt.

Supply and fix energy saving new generation 10W LED IP65 bulk head luminaire with opal diffuser complete all as specified and directed.

Supply and fix Distribution Board (SPN) double door 12 Way and should be IP 43 protected with Copper Bus bar 100 Amp rated, earth bar, neutral bar door earthing.

Supply and fix Distribution Board (SPN) double door 8 Way and should be IP 43 protected with Copper Bus bar 100 Amp rated, earth bar, neutral bar door earthing.

Supply and fix Distribution Board (SPN) double door 4 Way and should be IP 43 protected with Copper Bus bar 100 Amp rated, Earth Bar, neutral Bar Door Earthing.

Supply and fix MCB TPN complete 32 to 63 Amp with rupturing capacity 10 KA 'C' series, complete all as specified and directed.

Supply and fix MCB SPN complete 32 Amp with rupturing capacity 10 KA 'C' series, complete all as specified and directed.

Supply and fix MCB Single pole 6 to 32 Amp with rupturing capacity 10 KA 'C' series, complete all as specified and directed.

Supply and fix sub main wiring with single core cable 2x 6 sq mm FRLSH insulated unsheathed stranded copper conductor cable 1100 Volts grade in rigid PVC conduit (Concealed) medium grade alongwith 1 x 10 Sq mm FRLSH insulated unsheathed copper conductor cable as earth wire connected with main earth dolly including chesing, cutting & making good to match with the existing surface complete all as specified and directed.

Supply and fix sub main wiring with single core cable 2x 4 sq mm FRLSH insulated unsheathed stranded copper conductor cable 1100 Volts grade in rigid PVC conduit (Concealed) medium grade alongwith 1 x 4 Sq mm FRLSH insulated unsheathed copper conductor cable as earth wire connected with main earth dolly including chesing, cutting & making good to match with the existing surface complete all as specified and directed.

Supply and fixing single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB 20 Amps 240 volts complete all as specified and directed.

Taking down and refixing of Ceiling fan of any size/sweep, including oiling, Greasing and cleaning and applying two coats of synthetic enameled paint after preparation of surface complete over a coat of primer, all as specified and directed by Engr-in-charge.

Supply and fix of exhaust fan, steel body AC single phase. 230 V of size 300 mm sweep with, blades, and frame and louvers and including making of holes in wall etc all as directed by Engr-in-charge.

Taking down carefully after disconnecting electrical & water supply connections of storage type electric water heaters (Geysers) of capacity 25 liters of any make/type and refixing on its original/New position and reconnecting electric and water supply connections including replacement of nuts, bolts, washers, fastners etc and testing complete all as directed.

M & L for complete earthing with galvanised mild steel earth plate electrode of size 600x 600x 6mm thick burried directly in ground earth (in vertical) earth pit not less than 2.25 mtr deep below normal ground level with top edge of the earth plate not less than 1.5 mtr below ground level connected to galvanised iron or earth lead wire 4mm dia (8 SWG) by means of nut, bolt, check nuts and washer of galvanised ironl including PCC pit in PCC 1:2:4 type B-1 Pre-cast RCC cover slab using reinfocement with XPM weighing not less than 1.87 kg/Sqm with suitable handle made of 12mm round bar, including necessary excavation and earth work in any type of soil, 20mm dia medium grade galvanised steel tube for watering with one end fixed with cast iron funnel and wire mesh 15mm dia bore light grade galvanised steel tubing upto 7.5 m length for drawing earth lead wire protection, common salt, charcoal, etc complete all as shown in electrical plate No 3 of SSR Part-I and testing on completion.

Supply and fix Vertical Distribution Board (VTP&N) 4 way double door suitable for and including MCCB four pole as incomer and out going MCBs and should be IP 43 protected with Copper BusBars, Neutral Links, Earthing bar all as specified and directed. Note:- (i) MCCBs FP & SP shall be measured paid separately (ii) MCB & DB shall have the same make.

Supply and fix 4 Pole MCCB 125 Amp, 415 Volts with rupturing capacity 16 KA, complete all as specified and directed.

Supply & fix in replacement of PVC Conduit pipe of size 40 mm, ISI marked complete all as specified.

Supply, laying for replacement of unserviciable underground LT cable 1100 Volts grade heavy duty electric cable XLPE insulated & PVC outer sheathing with aluminium stranded conductor, armoured cable 70 Sq mm 3.5 core cable confirming to IS-7098 Part-I (1988) with latest ammendments of sizes.

Supply, laying underground LT cable 1100 Volts grade heavy duty electric cable XLPE insulated & PVC outer sheathing with aluminium stranded conductor, Armoured cable 16sq mm 2.0 core cable confirming to IS-7098 Part-I (1988) with latest ammendments of sizes.

Supply & laying dry river sand as cable cushioning 15cm thick layer before laying and 8cm thick over cable after laying the cable in trench complete all as specifieds and directed.

Supply & laying dry bricks over cable as mechanical protection layed flat with width equal to length of brick with sub class 'B' bricks complete all as specifieds and directed.

Material and labour for GI pipe light grade for road crossing/on wall/on pole with fixed clamps, nuts, bolts for cable protection of size 40mm dia complete all as specifieds and directed.

M & L Point wiring complete with 1.5 sqmm single core PVC insulated and unsheathed cable 1100 volts, FRLS grade with multistranded copper conductor ISI marked drawn through heavy duty PVC concealed conduit fixed to walls / roofs / floors / ceiling etc. and including provision of 1.5 sqmm stranded copper conductor cable as earth continuity conductor and connected to common earth dolly, including concealed MS box with 3 mm thick laminated sheet cover fixed with brass screws and cup washers for mounting of plate mounting for housing the switches, socket outlets, fan regulators etc, all as specified and as directed. (a) One Light / Exhaust Fan point controlled by one, one way switch 6 Amp complete

(b) One 3 pin socket outlet 6 amp independent

(c) One 3 pin socket outlet 6 amp same board

All as per srl item No 187 above but for one 3 pin socket outlet 16 Amp independent with cable of size 2.5 Sqmm for point wiring and 2.5 sqmm as in continuous earth wire.

Supply and fix switch piano, flush type single pole, one way 5 Amps capacity

Supply and fix socket outlet 2 in 1, 5 Pin, 6A

Supply and fix switch piano, flush type single pole, one way 15 Amps capacity

Supply and fix socket out let 2 in 1, 5 Pin, 16A combined

Supply and fixing ceiling fan complete with blade, down rods, and accessories, 230 V, 1200 mm sweep, Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) and connected from ceiling rose/ connector with & including suitable size flexible copper conductor PVC insulated sheathed cord, complete all as specified.

M&L for drilling and tapping cast iron/ Ductile iron water mains (in position) for branch connections of the internal dia 20mm ( for providing Straight plain brass ferrules or connecting screws).

M & L for Cutting existing cast iron /GI pipe in position for insertion of CI specials or GI fittings viz Tee,collar,bend or tail piece etc for 80 to 200 mm bore pipe including removing of blockage,cleaning of pipe line complete all as specified and directed by Engr-in-Charge

M&L for cutting of bituminous road/floor/culvert/PCC hard standing for laying of pipe /cable not exc 1.5 mtr wide and noy exc. 1.5 mtr deep including refilling/ with material and watering well ramming/ compacting and making good with PCC 1:2:4, type B-1, 100mm thick complete all as specified.

Supply and fixing of steel tubing galvanized medium grade with all fittings laid in trenches/ walls / Ceiling/ floor of size 25 mm dia all as directed by Engr-in-Charge.

Supply and fixing of gun metal,globe or gate valves of size 25 mm, with iron wheel head, screwed both ends for iron pipe and fixed.

M & L for construction of valve pit chamber having internal dimension 1.2m x 1.2m and depth 0.75m made of brick wall (full brick wall) with subclass 'B' bricks/concreate block works straight or curved on plan exc 6m mean radius and built in CM 1:6. incl plastering exposed surfaces with CM 1:4 and provn of pre cast valve pit cover of MS sheet 3 mm thick , frame works 40 x 40 x 5 mm MS Angle, dulypainted with synthetic enamel paint, with opening handle complete.

M & L for construction of valve pit chamber having internal dimension 0.6m x 0.6m and depth 0.75m made of brick wall (full brick wall) with subclass 'B' bricks, straight or curved on plan exc 6m mean radius and built in CM 1:6. incl plastering exposed surfaces with CM 1:4 and provn of pre cast valve pit cover of RCC, 50mm thick with opening handle complete.

Supply, installation, testing and commissioning of deep freezer hard glass top, with CFC free refrigerant (white CFHT 4058 double door deep freezer) suitable for operation on single phase 240 volt, 50 Hz. AC supply of capacity 350-405 ltrs air cooled sealed unit compressor (5 Star rating) with auto temperature control complete including connecting cord, plug top, with PVC bottom stand all as directed by Engr-in-charge. Make : BLUE STAR, VOLTAS, SHRI RAM (USHA), CARRIER

Supply, installation, testing and commissioning of refrigerators, electric driven (single phase) capacity more than 340 liters upto 360 litres BEE 5 star rated, (built in stabilizer inverter technology) suitable for operation on single phase 240 volt, 50 Hz. AC supply complete all as directed by Engr-in-charge. Make : WHIRLPOOL, LG, SAMSUNG, VOLTAS, VIDEOCON, KELVINATOR

Supply and fix Voltage stabilizer buck boost type, copper wound, wall mounted type for automatic operation single phase naturally air cooled indoor type & designed for input variation between 130 V to 300 V with output voltage stabilised at 230 V with accuracy of ± 2.5% and of capacity 1 KVA including inbuilt voltmeter with time delay relay all as directed by Engr-in-Charge. Make : POWERWARE, SINETRAC, VOLINA, MICROTECH, AAR KEY, VINITEC, ITE

M/S PARAMJEET SINGH