Certain repairs to hardstanding, paths, compound walls, fencing and other misc allied works at AF Stn Nal under GE (AF) Nal

Amount

Demolition of cement concrete (unreinforced) in ground floor and paving exc. 15 cm thickness above ground level and in any position complete all as specified and directed.

Dismantling of kerb stone set in cement mortar complete all as specified and directed.

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete all as specified and directed.

Dismantling of precast cement concrete interlocking paver block of any shape and size and refixing the same over sand cushion complete all as specified and directed. Note : sand for sand cushioning shall be measured and paid for separetly.

M&L cement concrete 1:4:8 type D-2 (using 40mm graded stone aggregate) as in sub base / sub-floor complete all as specified and directed.

M&L preparation of newly plastered or unplastered concrete surfaces (obtaining smooth surface) of any description not otherwise described over 10cm girth or width and applying two coats of synthetic enamel paint over a coat of primer complete all as specified and directed.

M&L complete removal of existing treatment on existing kerb stone (obtaining smooth surface) and applying applying two coats of synthetic enamel paint over a coat of primer complete all as specified and directed.

Refixing of old kerb stone in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete all as specified and directed.

M&L for sand filling under floors or in foundations including watering and consolidation for Interlocking paver block and similar works etc complete as specified and directed.

M&L Machine pressed M-35 Grade precast concrete interlocking paver block of glossy finished (rubber moulded) of approved shape and size confirming to IS 15658-2006 of 60 mm thickness complete all as specified and directed

All as per description of item No. 10 here in before but 80 mm thick

M&L 75mm thick cement concrete 1:4:8 type D-2 (using 40mm graded stone aggregate) as in sub base / sub-floor complete all as specified and directed.

S&F factory made rubber moulded, rubberized laboroda tiles, (Pre-Polished / glossy finish) of PCC type A-1, of approved colour and shape of size 400mm x 400mm x 30mm thick, jointed with neat cement slurry and pointed in white cement mixed with pigment to match the shade of tiles, fixed over 20 mm thick screed bed in CM 1:6 complete all as specified and directed.

S&F Non skid ceramic exterior floor tiles 10 mm thick (square) area of each tile exc 0.06 sqm but n exc 0.11 sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles, over 15 mm thick screed bed in CM 1:6 complete all as specified and directed.

Supply and laying design chequred cement concrete tiles 30mmx30mmx22mm thick made by table vibratory method set, jointed and pointed in neat cment slurry as in floors with grey cement & pigment over 20 mm thick screed bed in CM 1:6 complete all as specified and directed.

M&L PCC 1:2:4 type B-1 (using 20mm graded stone aggregate ) in roof kerbs or mud stops, rounded or chamfered on edges and the like finished fair and even including necessary form work complete all as specified and directed.

M&L 100 mm thick cement concrete 1:4:8 type D-2 (using 40mm graded stone aggregate) as in sub base / sub-floor complete all as specified and directed.

M&L 75 mm thick cement concrete 1:2:4 type B-2 (using 40mm graded stone aggregate) as in floors, finished the surface by making impressions of expanded metal, whilst the concrete is green complete all as specified and directed.

Forming Construction (Dummy) joints 65mm deep x 10mm wide, filled with sealing compound Grade 'B' complete all as specified and directed.

Forming Construction joints 30mm deep x 10mm wide filled with sealing compound compound Grade 'B' complete all as specified and directed.

Demolition of reinforced cement concrete of any description and in any position not other wise described complete all as specified and directed.

M&L for reinforced cement concrete 1:2:4 type B-1 (using 20mm graded stone aggregate) as in foundation including raft footing, foundation beams, plinth beams; base for column etc basementt slab, under reamed piles and mass concrete complete all as specified and directed.

M&L for reinforced cement concrete 1:2:4 type B-1 (using 20mm graded stone aggregate) as in Columns, pillars, piers, posts and struts complete all as specified and directed.

Use and waste of formwork to sides of concrete foundation footings, base of column and raft beams sides and soffits (if any) of foundation and plinth beams; and similar work vertical or to batter complete all as specified and directed.

Use and waste of formwork to sides columns of pillars, post, sturts, piers, column and stachions complete all as specified and directed.

M&L for precast reinforced cement concrete 1:2:4, type B-1 (using 20 mm graded stone aggregate) as in cover slab of manholes, Drain etc, set in cement mortar 1:4 complete all as specified and directed.

M&L for mild steel TMT Bars 10mm dia and over cut to length bend to shape required including cranking bending spirally for column, hooking ends & binding with and including mild steel mild steel wire (annealed not less that 0.90 mm dia or securing with chip) complete all as specified and directed.

All as per description of item No. 27.00 here in before but 6mm to 8mm dia.

M&L for mild steel round bar of 5mm dia and over upto and including 10mm dia complete all as specified and directed.

Demolition of brick or stone masonary built in cement mortar incl all quoins, arches, pillar etc. complete all as specified and directed.

M&L for brick work with sub class 'B' bricks old size, class 7.5 designation, straight or curved on plan exc 6 m mean radius built in cement mortar 1:6 complete all as specified and directed.

M&L for brick work with sub class 'B' bricks, in half brick thick walls, built in cement mortar 1:4 straight or curved on plan to any radius complete all as specified and directed

M&L as in repairs pre-cast cement concrete 1:2:4 type B-0 (using 12.5 mm graded stone aggregate) as in louvres and jallies, 25 mm thick (measured solid), including all mouldings but excluding frame, set in cement mortar 1:6 complete all as specified and directed

All as per description of item No. 33.00 here in before but except jallies (using old jallie)

M&L cement concrete in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, complete all as specified and directed.

M&L in repairs precast cement concrete 1:2:4 type B-0 (using 12.5 mm graded stone aggregate) louvres and jallies, 40 mm thick (measured solid), including all mouldings but excluding frame, set in cement mortar 1:4, complete all as specified and directed.

M&L as in repairs precast cement concrete 1:2:4 type B-0 (using 12.5 mm graded stone aggregate) post, ornamental moulded, 75mm x 75mm in section, total length of each post exceeding 45cm but not exceeding 60cm, with groves on two opposite sides for holding jalli 40mm thick, set in cement mortar 1:6, complete all as specified and directed.

Taking down cement plaster from brick or stone walls/ceiling etc including racking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

M&L 15mm thick rendering on fair faces of brick work or concrete surface in cement mortar 1:4, finished even and smooth without using extra cement complete all as specified and directed.

M&L preparation of newly plastered or unplastered surfaces of walls and applying two coats of acrylic emulsion exterior quality paint over and including a coat of primer exterior grade (tint as approved by GE) as in camouflage pattern complete all as specified and directed.

Dismantling posts or struts (wood, steel or R.C.C.) embedded in concrete, brick work, masonary etc. any section, including taking out embedded portion and making good disturbed ground complete all as specified and directed. Note:- (i) The demolished material shall be disposed off out side the MOD land. The contractor shall quote his rates considering the above fact. (ii) After dismantling, post holes shall be prepared for execution of new poles / struts. Cost of extra work, if any, is included in unit rate of this item and nothing extra shall be admissible on this account.

Excavation in post holes (or similar holes) each n exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers n exc. 25 cm in hard dense soil, watering and removing surplus soil to a distance n exc 50cm and making good surface complete all as specified and directed. Note:- This item is only applicable where the location of new poles/struts is changed from existing ploes removed against item No. 41 above.

Dismantling fencing wire mesh any type, any size complete all as specified and directed.

M&L for PCC 1:4:8 type D-2 (using 40mm graded stone aggregate) as in foundations, filling and mass concrete complete all as specified and directed.

M&L for PCC 1:3:6 type D-2 (using 40mm graded stone aggregate) as in pillars, boundary pillars and fencing posts (including caps and bases) complete all as specified and directed.

S&F joist / channel angle or tee sections fixed, welded, bent/cutting tops to shape as directed and embedded in concrete as in post, struts in fencing including necessary drilling holes, notching for wires etc (cut to ordinary lengths ie with in 20mm of the length indicated) Fe 290 grade E-165 complete all as specified and directed.

M&L mild steel flat iron (for securing wire mesh) bolt embedded in concrete including drilling bolts matching for wire including all necessary work and steel confirming to Fe-290 grade E-165 complete all as specified and directed.

Fixing only chain link fencing new or old including line wires any mesh, size and type of standards, rails, straining bolts, etc including provision of binding wire etc complete all as specified and directed. Note:- (i) Supply of new chain link Fencing shall be measured and paid for separately under respective item of this Schedule.

Supply only Galvanised mild steel chain link fencing, size wire and mesh as approved complete all as specified and directed. Note:- The payment for chain link fencing shall be made on the basis of weight of chain link fencing per square metre ascertained by a Board of officer convened by GE, by getting minimum 3 samples of each lot

S&F as in repair galvanised 2 strand steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails straining bolts including securing and tying at crossings with and provisions of galvanised mild steel wire staple or steel pins etc complete all as specified and directed.

Restraining and resecuring including making good staples etc galvanised 2 strand steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings complete all as specified and directed.

S&F mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut exc. 5cm but n. exc. 10cm long, dia of shank 11mm to 15mm complete all as specified and directed.

S&F mild steel round bars cut to length including, drilling, bending, hooking ends for securing wire mesh complete all as specified and directed.

M&L Preparation of new steel and iron surfaces of any description not otherwise described, over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

M&L Preparation of new steel and iron surfaces of any description not otherwise described, not exc 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

Taking down existing mild steel gate, area exceeding 2 sqm but not exceeding 6 sqm each and re-fixing the same in position after necessary repair by fixing, hold fasts, locking arrangement, handle etc complete all as specified and directed.

Dismantling of wrought iron or mild steel work of any description not ohterwise provided for complete all as specified and directed.

S&F framed work as in doors or gate of angle or other section with gussest plates, rails, braces etc complete drilled for fixing of steel sheeting or other covering. Doors etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings and hanging also fastening and fixing complete all as specified and directed.

Dismantling asbestos cement (corrugated or semi corrugated etc) sheets in roof covering complete all as specified and directed.

S&F MS rolled sections as in main and cross beams, hip and jack rafters common rafters and running rails and guides for sliding doors conforming to Fe.290.Gde-E-165 fixed with angle cleats or other connecting plates complete all as specified and directed.

S&F roof truss (framed), trussed purlin, crane, griders, rails and fastenings and heave brackets framing (beam, tee, agle channel or flat sections) including distance pieces, cleats etc. conforming to Fe.290.Gde-E-165 complete all as specified and directed.

S&F mild steel Framed brackets of angles or tees with web and flanges cut to shape, drilled and countersunk for screw, including bending and welding angles, as necessary, gusset plates, riveting, etc.including cutting tops to shape as directed, embeding in concrete and screwing etc, wind ties for roof including bolts drilling holes, notching for wire etc, flat iron fillets (for securing GI sheet etc) and including all necessary drilling or cutting holes in brick/ concrete surfaces and making good, welding work, bolting or reveting etc and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed.

S&F Pre-painted galvalume aluminum zinc 150 GSM coating GI based corrugated steel sheet 0.50mm thick of any approved colour having tensile strength of 550 Mpa as in roof covering / cladding to wall, ridges etc. fixed all as per manufactures's instructions and fixed with self tapping screw or hooks as required complete all as specified and directed.

S&F Pre-painted galvalume aluminum zinc 150 GSM coating GI based plain steel sheet 0.50mm thick of any approved colour having tensile strength of 550 Mpa as in roof covering / cladding to wall, ridges, flashing, eaves board valley gutter of any shape etc, cut to designed shape as directed at site fixed all as per manufactures's instructions and fixed with self tapping screw or hooks as required complete all as specified and directed.

S&F as in repairs 110mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches or floors complete all as specified and directed.

S&F as in repairs 110mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall including clamps as required complete all as specified and directed.

Excavation in trenches n exc 1.5 in depth, 1.5m wide for foundation etc and getting out in hard dense soil complete all as specified and directed.

Supply, laying and jointing in repair reinforced concrete pipes, class NP-2 with collars, 200mm Internal dia in trenches, and tested including all necessary extra joints, waste, and cutting etc. complete all as specified and directed. Note : Excavation and earthwork shall be measured and paid for separately

M&L for Concrete bed to drain pipe 200mm bore including packing under, and haunching in cement concrete 1:3:6 type C-2 (using 40mm graded crushed stone aggregate) against the sides of pipes after they are laid and tested complete all as specified and directed.

Removing execavated material n nexc 50m and depositing where directed at a level n exc 1.5m starting point complete all as specified and directed.

Returning filling including spreading levelling watering and well ramming in layers not exc 25cm each complete all as specified and directed.

M&L for cement concrete 1:3:6, type C-2 (using 40mm graded crushed stone aggregate) as in surface channel / drain complete all as specified and directed.

M&L Extra for forming fair finished drain channel 30cm inner girth in cement concrete using extra cement including forms / mould, mitred / stopped ends etc complete all as specified and directed.

Dismantling floor, hearth wall tiling including cement mortar bedding (but not backing) and rubbish off the premises complete all as specified and directed.

Supply and laying Glazed ceramic tiles in vertical surface 350mmx 250mmx 7 mm / 450mmX 350mmX 7mm thick, projected pattern elevation tile, set and jointed in neat cement slurry and pointed in white or colour cement to match including cement mortar backing coat of 10mm thick in cement mortar 1:4 complete all as specified and directed. Note: i) Colour, Type and pattern of tile shall be as apoproved by GE ii) Tile shall be projected pattern elevation tile and the tenderer shall quote his rate accordingly.

Taking down existing old Concertina coil any dia and re-fixing the same in position duly stretched, fixed to angle iron with 3mm dia GI wire, placed in existing Y / U shaped post erected over boundary wall and , complete all as specified and directed.

S&F as in repairs Alubond sheet i.e (ACP) Aluminum Composite Panel sheet having specification as Aluminum skin thickness: 0.12mm-0.50mm, panel thickness 6mm, Surface Treatment:PVDF (polyvinylidene fluoride) coating and embosing logo / letter writing (as approved) as per site requirement by means of radium tape including fixing to wall with decorative mirror holder brackets with 20mm dia stainless steel cap and 75mm length screws at spacing not less than 600mm on periphery of the sheet complete all as specified and directed. Note:- Rate includes writing of letters and embosing of logo as per the size, shape as directed by GE.

Dismantling of Stone slabs and tiles of any description or thickness in floors, aprons etc.laid bedded and pointed in any mortar complete all as specified and directed.

M&L Granite slab 18-20 mm thick (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite & including screed bed 15mm thick in CM 1:6 complete all as specified and directed.

M&L Granite stone slab 18-20 mm thick (of any type) (table rubbed and polished) for wall lining (veneering to wall) 12mm thick in cement mortar (1:3) and pointing with white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed.

Rounding only single edge of stone slabs such as in steps, cooking platform, and other similar situations complete all as specified and directed.

Supply and fixing in repair stainless steel (Grade 304) of railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement.

S&F as in repairs for stainless steel (Grade 304) letters made of hollow tubes, channels, plates etc., thickness 1.5mm to 1.6mm all over height of each letter n less than 150 mm including welding, grinding, buffing, polishing and making curvature (as required) and including engraving to granite / ACP / Metal Sheets with suitable fixing arrangements like nut & bolts, screw, Epoxy etc complete all as specified and directed.

SHREE GURU NANAK CONSTRUCTION COMPANY

RAJENDER ENTERPRISES

M/S BUDHRAM BISHNOI

m/s gaurav enterprises