COMPREHENSIVE REPAIRS TO COMPOUND WALL, GATE AND GATE PILLARS, PATHWAYS, FENCING AND OTHER MISC WORKS AT RIDGE AREA MD ACCN AND OTM ACCN UNDER AGE B/R-1 AT GE SATWARI

Amount

Note:- Please refer Appx 'D' of particular specification for the list of makes of BOQ items.

Demolition of Reinforced Cement Concrete (reinforcement cut as required to facilitate demolition) of any description and in any position not otherwise specifically provided and removing the rubbish from the work site out side defence permises, complete all as specified and as directed by Engr-in-Charge.

M&L for Use and waste of form work to sides and sofits of formwork to faces of walls, retaining walls, abutments, parapets and staircase railings and similar work including attached pillasters, buttresses,foundation etc.; vertical or to batter to obtain rough finished flat surface of concrete complete all as specified and as directed by Engr-in-Charge.

M&L for RCC (Nominal mix),Type B1 1:2:4 using 20 mm graded crushed stone aggregate as in foundations, including rafts, footings, foundation beam; plinth beams; bases of columns, etc.; basement slabs, under-reamed piles and mass concrete, complete all as specified and as directed.

M & L for TMT mild steel bars, 10mm dia and over, as in reinforcement, cut to length, bent to shape required including cranking, bending spirally or hooping for columns, hooking ends and binding with and including MS wire (annealed not less than 0.9mm dia) , complete all as specified and as directed.

M & L for TMT mild steel bars, 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders and binding with and includingMS wire (annealed not less than 0.9mm dia) , complete all as specified and as directed.

Demolition of Cement Concrete (un-reinforced) of any description and in any position not otherwise specifically provided and including removing from site to a distance n exc 500 mtrs , complete all as specified and as directed by Engr-in-Charge.

M&L for 75 mm thick plain cement concrete 1:3:6 type C-2 (using 40mm graded crushed stone aggregates) as in sub base to floors complete, all as specified and as directed by Engr-in-Charge

Providing and laying 60 mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand;complete, all as specified and as directed by Engr-in-Charge

Material and labour for Chequered Cement concrete tiles 30cm x 30cm and 25mm thick, machine pressed; set jointed and pointed in neat cement slurry with grey pigment cemen tand pigments and in floors, and cut and polished , over and including 15 mm thick screed bed or bedding layer in cement mortar 1:4 for laying floor finishes, complete all as specified and as directed by Engr-in-Charge.

M&L Pre-cast cement concrete block Type B1, 1:2:4 (20 mm graded agregate) as in kerb stone set in 1:6 cement mortar,fixed to side of foothpath complete all as specified.

Supply and fixing 110 mm bore, PVC (SWR) pipes single socketed in any length with rubber ring joints, laid in trenches or in floors, complete all as specified and as directed by Engr-in- Charge.

Providing cement concrete 1:2:4 type B-0 (using 12. 5 mm graded crushed stone aggregate) in steps, seismic and other similar bands, parapets and railings up to 60 cm in hieght, coping, kneeless apex stones , bed plates, roof padding, kerbs not provided for including weathering, slightly rounded or chamfered angles including necessary formwork complete, all as specified and as directed.

Dismantling posts or struts (wood, steel or R.C.C.) embedded in concrete, brick work masonry, etc., any section, including taking out embedded portion and making good disturbed ground complete all as specified and as directed by Engr-in-Charge.

Excavating in post holes (or similar holes) each n.exc 0.5cu m, getting ut,returning,filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding, 25cm watering and removing surplus soil to a distance n exc 50m and making good surface in any type of soil complete all as specified and as directed by the Engr-in-Charge.

M&L for Cement concrete type C2 1:3:6 (40mm crusted nstone graded aggregate) in foundations, filling and mass concrete as in walls or retaining walls, any thickness, size or shape including pilasters, buttresses columns, pillars, boundary pillars and posts (including caps and bases) complete all as specified and directed.

Supply only 2 inch aperture Chain link MS galvanized fencing ( 4mm dia wire) to fix with angle iron with flat iron with suitable nut bolt any size or type complete, all as specified and as directed.

Fixing only Chain link fencing including line wires, any mesh size and type to any type of standards rails straining bolts etc including provision of binding wireany size or type all as specified and directed.

S&F for joist, channel, angle, or tee section, fixed independantly, without connecting plates, etc. as in fencing post conforming to Fe 410 W (gde E-250 quality B) complete all as specified and directed.

S&F Mild steel flat iron for securing of chain link fencing conforming to Fe 290 Gde E-165 in post and strut in fencing including fabrication i.e. cutting tops drilling holes notching for wire welding etc..complete all as specified and directed.

S&F in repair Galvanised, 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails straining bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. as directed (each line wire to be measured) compete all as specified.

Mild steel round bars 10 mm dia, fix in chain link fencing using 0.90 mm dia GI wire as strengthing bar complete all as specified.Fe-410-W (Gde.E-250) quality-A or Fe 290 (Gde - E-165), complete all as specified and directed by the Engineer-in-Charge.

Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, not exc 5 cm long, dia of neck 5 to 10 mm complete, all as specified and as directed.

Demolition of brick work or stone masonry built in cement mortar including all quoins arches, pillars etc but excluding ashlar facing, dressed stone work and precast concrete articles and removing unserviceable material exc 100 mtrs, complete all as specified and directed by Engr-in-Charge

Brick work with old size sub class 'B' bricks, straight or curved on plan exc 6 m mean radius built in cement mortar 1:6, complete all as specified and as directed by Engr-in-Charge.

M & L for except Brick work with old size sub class 'B' bricks, straight or curved on plan exc 6 m mean radius built in cement mortar 1:6, complete all as specified and as directed by Engr-in-Charge.

Taking down cement plaster, any description on brick or stone or cement concrete walls including raking out joints, hacking for key, removing all type of vegetation (like peeple tree etc) scrubbing down with water and removing all the demolished material outside defence permises complete, all as specified and as directed by Engr-in-Charge.

M&L for rendering 15 mm thick in CM 1:6 on other than fair face of brick work/ stone wall surfaces finished even and smooth with out using extra cement all as specified.

15 mm thick rendering on fair faces of brick or concrete surfaces in cement mortar 1:4, finish surfaces even and smooth without using extra cement, complete all as specified and as directed.

M L for preparation of new plastered surfaces of walls, & applying two coats of oil bound distemper over one coat of wall care putty of 1 mm thick and one coat of primer complete all as specified.

Preparing newly plastered or unplastered surfaces of wall and applying two coats of cement base paint and including over a coat of chalk whiting, complete all as specified and as directed.

Plain cement concrete 1:3:6 type C-1 (using 20mm graded aggregate) as in surface channel and drain including all necessary form work, complete all as specified and directed.

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped ends etc.complete, all as specified and as directed by Engr-in-Charge

Repair to steel gates ( including Slot pin, Pintol hinge, Ball bearing, hook and eye of stander ad quality where required, resecuring of MS plates/sheets and Guard bars / grills by using welding equipments, complete all as specified and as directed by Engr-in-Charge.

Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete Fe-410- W(Gde- E-250) quality- B.

S & F Mild steel, plain, black sheet(1.25mm) in wall cladding, steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivetsand fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bendingor turning up, mitred angles, etc. as required, complete all as specified and as directed by Engr-in-Charge.

Preparation of new steel surfaces (with rubbing sand paper) of any description, over 10cm in width or girth, applying two coats of synthetic enamel paint and including over one coat of red oxide primer complete, all as specified and as directed by Engr-in-Charge.

M&L for applying one coat of synthetic enamel paint on old painted steel surfaces of any description having width/girth exceeding 10 cm including preparation and rubbing with sand paper to make surface even and smooth and apply putty and primer where requred complete all as specified

M&L for 50mm thick cement concrete 1:3:6, type C1, using 20mm graded crushed stone aggregate as in plinth protection, laid in slope of 1:20 and surface finished even and smooth without using extra cement including making joint at 3m interval and at each corner the joint shall be filled with bitumen mastic filling to full depth (comprising one part hot blown bitumen 85/25 and two part of sand), complete all as specified and directed.

M&L 16 to 18 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite, over 15 mm thick CM 1:4 as directed by Engr-in-charge.

Material and labour for precast cement concrete louvers and jallies, 40 mm thick (1:2:4) type B-0 (using 12.5 mm graded aggregate ) set in cement mortar 1:6, including all mouldings and dismantling old U/s broken Jallies at site, complete all as specified.

Dismantling of Asbestos cement (corruga ted, semicorrugated, etc.) sheets in roof coverings complete all as specified

S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed.

S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws and profile should match with galvalume sheet complete all as specified and as directed..

Dismantling of framed or unframed timber scantlings 40 sq. cm and over in section, in any position complete all as specified and directed.

S&F second class hard wood timber (framed) scantling fixed , wrought, complete all as specified and as directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed

S&F for Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. Fe 410-W(Gde E-250) quality-A complete all as specified and directed

Dismantling of ceiling board(Fibre,pulp,,any type of insulation etc) or insulation board / slabs/any thickness including cover fillets

Supply and fixing in repair GI snap grid frame work (Grid size 605cm x 605cm) for false ceiling consisting of main runner 'T' of size 24mm x 32mm and 0.3mm thick , Secondary runner 'T' of size 24mmx25mm and 0.3mm thick,GI angle 24mmx24mm and 0.4mm thick,Bottom exposed capping of width 24 mm of all T-sections shall be of 0.25mm thick PPGI, hot dipped galvanised steel with zink coating not less than 120gm / Sqm ,ceiling grid system duly suspended by 4mm dia GI wire hanging from existing purlins /roof slab with butterfly clips including Gypsum ceiling tiles of size 595 x 595 x 9 mm laminated with 0.07 mm thick polyvinyl film on the face side and 10 micron metalized polyester film on the back side fixed on GI snap grid including taking down of old us material complete all as specified and directed by Engr-in- Chage.

J P TECHNO

M/S ANIL MAHAJAN

M/S MOHAN LAL GUPTA

M/S Shesh Paul Gupta