PROVN OF TOILET AT GUARD POST NO 4 TROPO, ADDN/ALTN TO BATTERY CHARGING ROOM AT POWER HOUSE , REPAIR-RENOVATION TO BLDG NO P-38, ADDN/ALTN TO OLD OFFICER MESS AND ADDN/ALTN TO OPS ROOM AND SPECIAL REPAIR TO BLDG NO P-1 TROPO COMPLEX ETC

Amount

Taking down cement plaster on brickwalls & concrete surfaces & the like including racking out joints, hacking for key scrubbing down with water etc. any description, complete all as specified and directed.

M & L for rendering 15mm thick on fair faces of brick work or concrete in CM (1:6) & rendering is to be finishing even & smooth without using extra cement, complete all as specified and directed.

M & L for rendering 15mm thick on fair faces of brick work or concrete in CM (1:4) & rendering is to be finishing even & smooth without using extra cement complete all as specified and directed.

M&L for Rendering 10 mm thick over ceiling of brick work or concrete surface in CM 1:3 finished even & smooth without using extra cement complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store & rubbish off the premises.

M & L first quality coloured glazed ceramic tiles, fixed in pattern of different colour between including and border highlighter of size 300x 450 x 7mm thick as in vertical surfaces such as dado/skirting, set and jointed in neat cement slurry and pointed in white or coloured cement to match with colour of tiles laid on and including 10 mm thick rendering in cement mortar (1:3), including pointing in white cement with pigment to match the shade of tiles, complete all as specified and directed. Note :- Pattern of the tiles will be decided by GE at the time of execution.

M&L, Non-skid ceramic coloured tiles 7 to 8 mm thick (square/rectangular) area of each tile exc 0.06 sqm but n.exc 0.11 sqm, in floors etc. set & jointed in neat cement slurry & pointed in white or coloured cement over & incl 15mm thick screed bed in CM (1:6) complete all as specified.

M&L, Non-skid ceramic coloured tiles 10 to 12 mm thick (square/rectangular) area of each tile exc 0.11 sqm but n.exc 0.18 sqm, in floors etc. set & jointed in neat cement slurry & pointed in white or coloured cement over & incl 15mm thick screed bed in CM (1:6) complete all as specified.

M&L Vitrified tiles , light shade,10 mm thick( square/rectangular) polished ,area of each tile not exceeding 0.36 sqm , laid in floors with neat cement slurry @ 3.00 Kg/square over & incl 15 mm thick screed bed in cement mortar 1:6, including pointing in white or coloured cement to match the shade of tiles, complete all as specified and directed.

All as per Srl item No 08 above but as in skirting, dados, laid over & incl 10 mm thick rendering of CM(1:4) .

Demolition of brick work in any position, built in cement morter or cement lime mortar etc complete all as specified and directed Engineer - in - charge.

M&L for Brickwork with sub class ‘B’ bricks straight or curved on plan exc. 6mtr mean radius built in cement mortar 1:6 using old size bricks, complete all as specified

Demolition of cement concrete of any description (un-reinforced) in ground floors and paving n exc. 15 cm thickness (below or above ground level), complete all as specified

M & L for 75 mm thick, plain cement concrete 1:3:6, type C-2, using 40 mm graded mechanically crushed stone aggregates, laid in 1:20 slope as in plinth protection including making joints at 3.00 metre intervals and at each corner, the joint shall be filled with mastic filling (to full depth) comprising of one part heated hot blown bitumen 85/ 25 & two parts heated sand (by volume), surface finished even and smooth without using extra cement, complete all as specified.Note: The concrete shall be laid at a stretch not exceeding 3 metre in length and width of joint shall not be more than 12 mm, complete all as specified

M&L for 40mm thick PCC (1:2:4) type B-1 using 20mm graded stone aggregates as in flooring finished even & smooth without using extra cement, complete all as specified.

S&F for Glass dividing strips, 3 mm thick, 38mm wide & inserted in position to confirm to design, complete all as specified.

M&L for Plain cement concrete 1:4:8 Type D-2 (using 40mm graded stone aggregate) 100 mm thick as in sub base complete all as specified and as directed.

M&L for 20 mm thick cement concrete Ultra pre polished designer tiles for heavy duty floors manufactured with cement, blue metals, sand, chemicals and inorganic pigments as per IS – 1237 of 1980 (Re-affirmed of 1996) smooth of approved patterns and design over and including 25 mm thick cement screed bed in CM 1:4 set and jointed in neat cement slurry and pointed in white cement with admixture of pigment to match colour /shade/matrix of tiles complete all as specified and directed by Engineer-in-Charge.

Demolition of stone slabs and tiles of any description or thickness in floors, apron etc complete all as specified and directed by Engineer-in-charge.

M&L for granite tiles/slab of sizes as directed (of any type) 18 mm thick machine cut,bedded over 20 mm thick in CM1:4 and jointed with grey cement slurry and pointed with white cement with admitures of pigment to match with shade of grnite stone incl grinding and polishing complte all as specified.

Complete all as per item No 20 here-in-after but over 10 mm thick rendering of CM in 1:4 on vertical serfaces

M&L machine cut and machine polished kota stone slab flooring 18-20 mm thick over & incl 20 mm thick cement screed bed in CM 1:6, laid and jointed with grey cement slurry mixed with pigment to mtach the shade of the slab including rubbing and mirror / granite polishing complete all as specified and as directed

M&L machine cut and machine polished kota stone slab 18-20mm thick , bedded over & incl 10mm thick rendering of CM 1:4 in riser and steps, skirting, dado and pillar aid and jointed with grey cement slurry mixed with pigment to mtach the shade of the slab including rubbing and mirror / granite polishing complete all as specified and as directed

Taking down chowkhats or frames with shutters ( without tacking off shutters from the frames) n.exc. 1.5 sqm each, complete all as specified.

Taking down chowkhats or frames with shutters ( without tacking off shutters from the frames) exc. 1.5 sqm but n.exc 4.0 Sqm each, complete all as specified.

S&F solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube supply & fixing in opening as per specification.

S&F factory made solid panel PVC Door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail,lock rail and bottom rail on either side as gap insert for top rails, bottom rail,panelling of plain colour PVC sheet to be fitting in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement, supply & fixing in the frame at site as per specification and drg, making good disturbed portion to match existing surface complete in all respect as specified.

S & F flush shutter 35mm thick solid core construction with block board core and plywood face panels commercial type on both sides with lipping / frame to match all as specified and directed by Engineer - in - Charge.

S&F steel windows or ventilators, fixed type with glazing bars & wire mess complete all as specified and directed by Engineer-in charge.

M & L for PCC (1:2:4) type B-1 using 20mm graded stone aggregates as in bed plocks, complete all as specified.

S&F, 150mm aluminium handles, cast type, anodised, complete all as specified.

S&F 200mm long aluminium anodized barrel tower bolt of extruded section & fixed, complete all as specified.

S&F, 100 mm mild steel butt hinges, medium weight, cold rolled & welded / fixed with chowkats,complete all as specified.

S & F aluminium alloy, anodised, sliding door bolt with hasp staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed length of bolt 300mm ,bolts not less than 12mm dia with and including a minimum of 6 bolt and nuts ,four on bolt plate and two stapple plate complete (ISI marked)

Hacking out old broken glass of any thickness, size, quality or description from n exc. 0.50 sqm in each pane metal frame glazed with oil putty or fixed with beads including punching or out old glazing pins, spring clips, complete all as specified.

S&F, 4mm thick sheet glass ordinary quality & glazing with oil putty in square n exc. 0.50 sqm in each pane, complete all as specified.

S&F in 4 mm thick frosted glass in square nexc 0.50 sqm each pane fixed with putty (in metal frames etc) complete all as specified.

S&F power coated aluminium frame work for doors, windows ,partitions etc incl grill for windows for windows etc with one or more rebated section incl jointing cleats for fixing etc complete complete.

S&F power coated anodised aluminium door shutters, partition wall, aluminium section weighting 0.55 Kg/Rm incl necessary joining cleats glazing clips rubber neoprene packing, handles two Nos in each door, hinges anodised aluminium snap beading screws etc complete all as specified and as directed.

S&F powder coated anodised aluminium window and ventilator shutters , side hung type without sash bars aluminium section weighting 0.55 Kg/Rm incl necessary joining cleats glazing clips rubber packing, aluminium anodised snap beading, screws, anodised aluminium fittings such as peg stays 150 mm long (1Nos0, hinges type B-21 100 mm long(2Nos) suitable handles (1Nos)complete all as specified and as directed.

S&F 12 mm thick prelaminated board, exterior grade, prelaminated one side with decorative choice lamination and other side balancing white lamination fixed with screws to aluminium frame work complete.all as specified and directed.

S&F double action floor spring hydraulic regulated made up of min 1.25 mm thick aluminium sheet foundation box, main body with stainless steel cover, govering pivets made of brass, other part made up of mild steel heavy duty complete. all as specified and directed.

S&F brass six lever dead lock suitable for aluminium doors manufactured by Harrison Locks or Godrej as approved by GE.

S&F in repairs false ceiling with exposed GI system using “SILHOUETTE XL 15 mm (Nominal) designer Grid "Armstrong" white or Global white with black reveal and 600 x 600 x 15 mm thick prime fine fissured micro look white/coloured tiles (superfine 15mm/silhouette). Making necessary framework for AC ducting, if any and necessary cutouts for diffusers and light fittings, taping and finishing to proper line & level .M/s Armstrong ceiling complete all as per manufacturer’s instructions and as directed by Engineer-in-Charge.

Taking down existing bitumen felt roof treatment including cement mortar bedding and cleaning the surface and removal outside the MOD land, complete all as specified and directed.

M&L Plain cement concrete (1:2:4) type B-1, using 20 mm graded mechanically crushed stone aggregates as in padding to roof to maintain the required slope and finished the surface even and smooth without using extra cement, complete all as specified

Roughening of surfaces of old concrete slab by wire brushing, sweeping, cleaning and washing down to remove all loose dust etc. and brushing neat cement slurry @ 3.00 kg/Square Metre on roof surface, complete all as specified.

Material and labour, 10mm thick cement plaster in CM (1:4) mixed with WPC as per manufacturer’s instructions @ 3% by weight of cement on concrete surfaces, finished even and smooth without using extra cement complete all as specified and directed. Note : WPC shall be measured and paid separately.

Cutting groove in brick wall 75 mm wide and 65 mm deep for inserting APP polymer membrane and shaping horizontal face of groove with cement mortar 1:3, including removal of rubbish outside MoD land, complete all as specified.

Material and labour, water proofing treatment of roof consisting as under:- (a) Applying evenly a coat of bituminous primer conforming to IS-3384:1986 @ 0.30 litre/sqm including preparation of roof surfaces (b) A layer of 3mm thick APP polymeric membrane of weight not less than 3.60 kg/sqm, reinforced with polyester non-woven fabric (weight not less than 160gm/sqm), duly sealed at over laps & joints with flame (by torch application) all as per manufacturer’s instructions, complete all as specified and directed.

Complete all as per Srl item No. 53 here-in-before but on vertical surfaces, using hot blown bitumen having penetration value 30/40 applied 1.20 Kg/ Sq.m over primer @ 0.30 litre/ Sq.m, complete all as specified and directed by Engineer-in-Charge.

M & L for plain cement concrete (1:2:4) type B-1, using 20 mm graded mechanically crushed stone aggregates as in mud stops, sides of interlocking tiles and similar work and finishing the surfaces even and smooth without using extra cement, complete all as specified

Demolation and breaking up drain pipes any size and any discription (salt glazed ware, AC or reinforced) set in cement mortar incl demolation of PCC haunching etc, complete all as specified.

M&L for cement concrete (1:2:4) type B-1 using 20 mm graded stone aggregates as in surface channels and drains complete all as specified and directed

M&L for reinforced concrete pipes 150 mm dia, class NP-2, laid and jointed complete with collars etc complete all as specified and as directed

M&L for 150 mm dia salt galzed stone ware (SGSW) drain pipe, grade 'A' laid in trenches and jointed complete all as specified and as directed

M&L cement concrete 1:3:6 type C-2 for 150 mm dia in bed to drain pipes including packing under, and haunching against the sides of pipes etc complete all as specified and as directed

M&L for cutting into existing manholes for connecting new drains, internal dia of pipe 150 mm, making good to pipe and rendering, cutting out existing benching for and foring branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 tye B-1 smoot finished, and re-forming benching as required etc complete all as specified and as directed

Supply only Integral water proofing compound

S&F in repair vitreous China Urinal, half stall type white including CP brass spreader, CP waste fittings 32mm size and waste pipe including bracket complete all as specified and directed by Engineer-in-Charge.

S&F in repair Toilet paper holder ,chromium plated , fixed to walls with chromium plated (CP) brass screws, complete all as specified and directed by Engineer-in-Charge.

S&F Health faucet with tube and hooks, chromium plated fancy type fixed to plugs with chromium plated brass screws.complete all as specified and directed.

S&F venetion blind vertical type complete all as specified

Dismantling mild steel work of any description not otherwise provided for complete all as specified and directed by Engineer-in-Charge.

S&F framed work such as grills,gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work con- forming to Fe.290.Gde-E-165

S&F mild steel work as in duct cover incl frame for the duct coverand similar work conforming to Fe-290 Gde-E-165, complete .

Taking up or down 15 mm steel tubing & connections fixed complete to walls and ceiling or laid in floors, complete all as specified.

Taking up or down 20mm dia bore of galvanised Iron steel tubing and connections including cleaning for refixing, cutting/chauging in wall/floor complete in all respect as specified

Taking up or down 50mm dia bore of galvanised Iron steel tubing and connections including cleaning for refixing, cutting/chauging in wall/floor complete in all respect as specified

S&F 15mm bore dia of medium grade galvanised steel tubing with all fittings and fixed complete to wall or laid in floor complete in all respect as specified

S&F 20mm bore dia of medium grade galvanised steel tubing with all fittings and fixed complete to wall or laid in floor complete in all respect as specified

Complete all as per Srl Item No. 73.00 here in before but for 25mm bore all as specified and directed by Engineer - in - Charge.

S&F 50mm bore dia of medium grade galvanised steel tubing with all fittings and fixed complete to wall or laid in floor complete in all respect as specified

M&L 18 mm/ 19 mm thick prelaminated particle board, exterior grade, prelaminated both sides with decorative choice lamination for wooden and fixed with screws to timber frame as in cupboards, shutters, shelves, pelmet etc. including fixing 18 mm wide 6 mm thick beading of Ist class HW (Teak) all around, fixed in repairs, complete all as specified and directed by Engineer-in-Charge.

Supply & fixing block board 18/19 mm thick, grade 2 quality, interior grade, commercial type fixed with screws to timber frame as in cupboards, shutters, shelves, pelmet etc. including fixing 18 mm wide 6 mm thick beading of Ist class HW (Teak) all around, fixed in repairs, complete all as specified and directed by Engineer-in-Charge.

S & F plain fillets square, rectangular or triangular in section, 2nd class hardwood of sectional area exc 13 & n exc 25 sqcm, clean sawn, wrought finished secured with screws complete all as directed.

S&F Continuous (piano) hinges, mild steel, bright finish or electro galvanised, 30 mm wide flap (when open), fixed in repairs, complete all as specified.

S&F100 mm size hasp and staple, safety type, aluminium anodized with mild steel hinge pin including bolt to hinge plate and fixed with screws, fixed in repairs, complete all as specified.

S & F in repairs 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall complete all as specified.

S & F in repairs 75 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall complete all as specified.

S & F in repairs 110mm bore PVC (SWR) bends any radius complete all as specified.

S & F in repairs 75 mm bore PVC (SWR) bends any radius complete all as specified.

Supply and fix in repair Vitreous China wash down water closet'constellation premium of Hindware white colour complete set incl cistern with lid cover fixed in repairs, including connection to wate pipe, flushing pipe, anti-syphonage pipe etc. and making good to floor complete all as specified and directed.

S&F in repairs Wash basins (oval type), vitreous china, white, flat back of size 550x400mm including brackets and cutting for and pinning in ends of brackets or erecting stand 32mm dia waste fittings, brass, chromium plated with long screwed shanks and fly nuts, 32mm dia HDPE waste pipe and including new brackets complete all as specified and directed.

S&F in repairs vitreous china squating pan, 'Orissa' pattern, size 580x440mm white, with integral foot rests, including 100mm cast iron 'P' or 'S' trap and 100mm cast iron sanitary connection socket to fit WC outlet including connection to trap, to flushing pipe, anti-syphonage pipe etc. complete including making good to floor complete all as specified and directed.

Supply and fix Vitreous China wash down water closet (wall mounted/pedestal pattern), white (excluding fixing bolts flushing cistern and flush pipe), fixed in repairs, including connection to wate pipe, flushing pipe, anti-syphonage pipe etc. and making good to floor complete all as specified and directed by Engineer - in -Charge.

Plastic water closet seat black/ white closed pattern with flat bottom and cover and mild steel chromium plated or aluminium hinging devices, connected to drains outlet, fixed in repairs, complete all as specified and directed by Engineer - in -Charge.

S&F in repair SS Jet for water closet pedastal pattern , complete all as specified and directed by Engineer - in -Charge.

S&F Towel rail 600 mm long, 20 mm dia, ‘D’ type, brass, chromium plated, fixed to walls with screws and plastic cleats, fixed in repairs, complete all as specified.

S & F in repairs 20mm ball valve, high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball, screwed for iron pipe (Minimum weight 210 gms) complete all as specified and directed.

S & F in repairs 10 litres capacity, PVC valve less, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets and suitable flush pipe PVC 32mm dia complete all as specified and directed.

S & f in repairs bib taps, cast copper alloy, chromium plated, with crutch or butterfly handle, screwed down, screwed for 15 mm bore iron pipe or for brass ferrule complete all as specified.

S & F in repairs Pillar taps (Single Touch type), cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly nuts, screwed for 15mm bore iron pipe and pillar tab to be prior approval from Engr in Charge complete all as specified.

S & F in repairs angle cock/stop valves, cast copper alloy, chromium plated, fancy type, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for 15 mm bore iron pipe or for brass ferrule complete all as specified.

S & F in repairs stop valves, cast copper alloy, chromium plated, fancy type, with long shank and cup (concealed type), screwed down, high pressure, with crutch or butter fly handle, screwed both ends for 15mm bore iron pipe or for unions complete all as specified.

S&F in repairs 15mm dia gun metal gate valve, with iron wheel head, screwed both ends for iron pipes complete all as directed by Engr in Charge.

S&F in repairs 20mm dia gun metal gate valve, with iron wheel head, screwed both ends for iron pipes complete all as directed by Engr in Charge.

S&F PVC connection 15mm size with PTMT nuts of length 450mm complete all as specified and directed.

Dismantling exsiting water tanks exc 500 ltr and n.ec 1000 ltr capacity and removal from site.

Complete all as per item No. 101.00 here-in-before but exc 250 ltr and nexc 500 ltr capacity.

S&F 1000 litres capacity Rotational moulded polyethylene water storage tanks (Cylindrical vertical with closed top) hoisted & fixed in position including Tank Nipple and with union (Two Nos each) , fittings complete in all respect as specified.

Complete all as per item No.103.00 here-in-before but 500 ltr capacity.

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for (reinforcement cut as required to facilitate demolition), complete all as specified.

M&L for providing precast reinforcement cement concrete (1:2:4) type B-1 using 20mm graded aggregate in man holes covers slabs/ Shelves as in slabs supported on walls, beams and columns, in floors, roofs, landings, deck slabs and in shelves and like including necessary form work, complete all as specified and directed by Engr-in-Charge.all as specified.

M & L for for mild steel deformed bars 08 mm dia & over cut to length , bent to shape required, including cranking, bending spirally binding wire (0.9mm dia annealed) complete in all respect as specified.

Preparation of newly plastered surfaces of wall of any description & applying two coats of exterior acrylic emulsion paint in camouflaging pattern ( in multi shades as approved) over a coat of primer, complete all as specified.

M&L complete removal of existing treatment by scraping down completely on brick wall/concrete surfaces thoroughly, washing, rubbing down with water cleaning the surface upto the entire satisfaction of Engineer-in-Charge and applying two coats of exterior weather proof paint over and incl one coat of primer on old or new surface of walls/roofs of desired tints / colour after preparation the surface by making surfaces compleetly smooth by filling holes with birla white care putty in camougflage pattern by using three or more colour as required complete and all as specified and directed by engineer in charge (NOTE : for camougflage three or four colour of different shade to be used as directed by engineer in charge (ii) Pattern shall be approved by user unit.)

M & L preparation of newly plastered surface of ceiling and applying three coats of white wash up to 4 mtr height complete.

Preparation of old surfaces of ceiling including brooming down or steel wire brushing; scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots etc. and applying one coat of white wash up to 4 mtr height , complete all as specified and directed.

Preparation of new wooden surfaces & applying two coats of synthetic enamel paint over a coat of pink primer to wood surfaces over 10cm in width or girth not otherwise described, complete all as specified.

Preparation of old painted wooden surfaces over 10 cm width or girth not otherwise described and applying one coat of synthetic enamel paint, complete all as specified.

Preparation of new steel surfaces & apply 2 coat of synthetic enamel paint over a coat of red oxide over 10cm in width or girth not otherwise described, complete all as specified.

Preparation of old painted steel or iron surfaces over 10 cm width or girth not otherwise described and applying one coat of synthetic enamel paint, complete all as specified.

Taking down 100mm/75mm bore cast iron soil, waste and vent pipes including fittings by burning out lead joints etc to facilitate dismantling old serviceable fittings/pipes laid in trenches, floors or fixed to walls all as directed including earth worm, demolition of PCC/Brick work and making good to match with existing

S&F 100mm bore cast iron sand soil waste or vent pipes(ISI marked) in any length with or without ears with cement joints fixed to wall all as directed

S&F 75mm bore cast iron sand soil waste or vent pipes(ISI marked) in any length with or without ears with cement joints fixed to wall all as directed

S&F 100mm bore cast iron branch pipes single (equal or unequal dia) ordinary of inverted spigot or socket type (ISI marked)

S&F 75mm bore cast iron branch pipes single (equal or unequal dia) ordinary of inverted spigot or socket type(ISI marked)

S&F 100mm dia bore cast iron bends (any radius) (ISI marked) diminishing pieces or tapers (large bore measured)

S&F 75mm bore cast iron bends (any radius) diminishing pieces or tapers (large bore measured) (ISI marked)

S&F in repairs CI nahani trap with grating including jointing to waste pipe in run lead with dia of outlet 75 mm including floor around to required depth and burning lead joints etc to facilitate dismantling old CI trap and making good complete all as directed. (ISI marked)

S&F in repairs 100mm dia bore 'P & S' trap fixed with cement joint surface all as directed and specified.

Dismantling wall and ceiling board any thickness, including cover fillets etc complete all as specified and directed by Engineer-in-Charge.

M&L for perforated particle board/tiles12 mm for insulation and accoustic purposes 30x30 cm or 60x60 cm in size,fixed with nails in ceiling fixed in repairs

Preparation of old painted celing or Wall board surfaces over 10 cm width or girth not otherwise described and applying one coat of synthetic enamel paint, complete all as specified.

Cutting holes in brick walls exceeding half brick but not exceeding one brick built in cement mortar for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or PCC 1:2:4, including removal of rubbish outside MoD land, complete all as specified.

Cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exceeding 10 cm girth, including removal of rubbish outside MoD land complete all as specified.

Dismantling sheet as in roofing etc of any description and any specification

M&L for Pre- painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified

M&L Gunitting work for RCC work as in columns, beam, slab, perapet, chajjas etc by removing all loose concrete on the reinforcement, cleaning the surfaces with wire brushes and reinforcement with sand papers than applying apoxy paint to rusted reinforcement and S&F welded wire mesh fabric size not less than 95x95x3 mm on the prepare surfaces and finally applying guniniting 30 to 40 mm thick (average thickness )with presure gun using 1 part of cement and 3 part of coarse cement incl necessary form work and scafolding where ever required all gunnited surface shall be brought in complete geometric figure even in the guniting opration only and including Removal of debries/broken/demolished material at a distance exc 250 mtr and n exc 500 mtr from the site incl loading and unloading to any type of vehicles complete all as specified and directed. Note :- Where new or additional reinforcement is required the same shall be paid for separetaly of this schedule as above.

Supply only TMT steel bars for reinforcement in required length and dia, complete all as specified and directed.

Supply only welded steel wire fabric, weight not exc 4kg/sqm, complete all as specified and directed.

S&F Collapsible steel gates, top hung, consisting of channel pickets, pivoted flat bars, top and bottom runners, brass handles etc., as specified, erected in position and securing runners with holdfasts and brackets, complete all as specifiend and directed

M & L in repairs for Providing and fixing PVC sheet wall (prelam wood veneers design) panelling of thickness 5 mm consisting of panels having size 1220 mm X 2440 mm stuck on internal framework of 50 mm wide strips of 5 mm thick PVC sheet, the strip should have in there centre a groove of 6 mm thick width and 1 mm depth for sinking the head of the screw used to fix the strips to the wall vertically at an equal interval of 10 inches between two pvc strips. The PVC sheets shall be fixed to the wall using 65 mm long MS screws through the groove in the strip by using PVC fasteners; the distance between two screws shall not be more than 200 mm, a groove of 12 mm may be left at the joint of the panel for aesthetic looks. The exact size of the panel and correspondingly of the grid may vary depending on the size of the wall. Optionally a strip of 5 mm thick PVC sheet of width 5 mm thick PVC sheet of width 75 mm feathered at the edge shall be stuck at the place where two panels are jointed using solvent compound complete all as specified and directed by Engineer - in - Charge.

Taking down aluminium door shutter of any size upto 4 Sqm each and replacement of defecting pivot with new pivot & refixing in position complete all as specified and directed by Engineer-in-Charge.

Taking down aluminium door shutters of any size upto 4 Sqm each replacement of defecting floor spring with new floor spring make : Amar/Sandhu or equivalent make as sample approved by GE.

S&F in repair Mortice dead lock 100mm size, 4 lever brass lock for aluminium door shutter complete all as specified and directed by Engineer-in-Charge.

Taking down old broken glass from aluminium door, window or partition panel by removing glass clips and S&F glass ordinary 5.0mm thick in any size and refixing the glass clips in position after replacing rubber gasket complete all as specified and directed by Engineer-in-Charge.

S&F in repair Hydraulic door closer for aluminium door shutter complete all as specified and directed by Engineer-in-Charge.

S&F steel work in tubular trusses, rafters and posts etc including special shaped washer etc. complete using ERW or induction butt welded Squre/ Rectangular tubes conforming to IS-1161-1979 (grade st-240)all as specified and directed by Engineer - in - Charge.

S&F Mild steel plates (plain or chequered) channels, square cut or notched etc complete all as specified and directed by Engineer - in - Charge .

S & F mild steel as in framed work as in doors or gates of angles or other section etc. complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive for steel sheeting or other covering, running rails and guides) and hanging also fastening and fixing incl MS hinges, handles ms sheets 0.63 mm thick complete Fe 410-0 all as specified and directed by Engr-in-Charge.

M&L for Plain cement concrete ( 1:2:4), type B-1, (using 20 mm graded stone aggregate) as in coping bedplates & other similar works, including necessary form works wearthering, slightly rounded angles and theading, complete all as specified.

M&L for averaging 3 mm thick putty and applying one coat of primer complete all as specified and directed by Engineer-in-Charge.

M&L, applying two coats of distemper oil emulsion over new surfaces including preparation of new surfaces, finished even and smooth using chalk whiting except primer complete all as specified and directed by Engg in charge.

S & F pressed steel door frames with one or more rebates including necessary fixing lugs hinges lock strike plate etc complete all as specified size of frame 125 x 60mm all as specified and directed by Engineer - in - Charge .

M&L for providing cement concrete 1:2:4 Type B1 using 20mm graded stone aggregate as in Slabs supported on walls , beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed by Engineer in charge.

Use and waste of form work to sides and soffits of floor or roof beam, beam haunchings, girders bressummers, lintels, cantilevers, shelves including supports, overhangs etc also splays between floors and beams etc complete all as specified and directed by Engineer in charge.

Mild steel TMT bars 10 mm dia and over cut to length, bent to shape required, including cranking, bending etc, and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips, complete all as specified.

All as per Srl item No. 151.00 here in before but 5mm and over for as in stirrups, spacers and binders all as specified and directed by Engineer - in - Charge.

M&L for providing for framless glazing with laminated toughened glass fitted with stainless steel spider fittings (2way/4way) splice plate, fin plate routel and stainless steel fastener etc with 12 mm thick glass support finish complete all as specified and as directed by Engineer-in-Charge.

Preparation of old surfaces of walls including brooming down or steel wire brushing , scraping down smook soots , moulds, mass and efflorescence salts and trading oils and gresy spots etc, and applying Two coat of oil bound distemper of approved shade , complete all as specified and directed by Engineer-in-Charge

Cutting out concrete blocks of precast cement concrete Type B1 1:2:4, columns, slabs, brick work or stone masonry (in alternate course) forming toothings for and bonding new work in mortar set in cement mortar 1:4 into old work, including new material entering old wall complete all as specified & directed.

M&L for brickwork with sub class `B' bricks (old size), straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4 complete all as specified and as directed by the Engineer-in-Charge.

S&F window / ventilator section of frame 72x50 mm fixed to wall or concrete surface with rowl plugs made, of galvanized steel powder coated and section of shutter 47x20 mm ,mulion section 72x50 mm (Base steel as per IS 513 "D" quality galvanized as per IS 277 with zinc of 120 gms/sqm.) glazed or gauged and wire gauge shutter prepare to receive wire mesh to the shutter(Double door shutter) with total coated thickness of 0.6 mm including grills/guard bars made of square bars powder coated fixed to windows frame with screws at 150mm c/c both ways, 4 to 5 mm thick sheet glass, 0.36mm stainless steel wire cloth with 1.40mm aperture necessory fittings and all builders hardware such as handles, tower bolts & stays etc. complete all as specified and as directed Make:- NCL type-4000 series or equivalent make as approved by GE.

S&F powder coated aluminium anodized door frame and fully glazed shutter divided in to two glazed panels including aluminium anodized snap beading and rubber gasket / lining for fixing of glass as directed. The frame shall be fixed with aluminium anodized bolt by drilling in the existing wall and with thrust bolt of suitable size all as directed. The frame and shutter will be made out of the following sections and fittings: (a) Aluminium anodized door frame 101.60mm x44.45mm x2.01mm fixed with aluminium board and thurst bolt in walls by drilling as directed Aluminium anodized top, bottom rails of shutter section no 19519 of jindal and Shutter Vertical Stiles Section No. 19560 of jindal (b) Aluminium anodized lock rail of shutter section no 19564 (c) Brass six lever dead lock suitable for aluminium doors manufactured by Harrison Locks or Godrej as approved – 01 No for each door(d) Aluminium anodized tower bolt 200mmlong size Make Classic or Argent – 02 No in each door(e) Aluminium anodized fancy handle 250mm long Make Classic or Argent – 02 No in each door(f) Glass pane shall be 5.5mm thick tinted glass of size as required(g) Floor spring hydraulic heavy duty and pivot arm Make Everite/ Sandhu – 01 No for each door

S&F rolled mild steel conforming to Fe 290-0 or Fe -330-0 on angle iron section of any size fixed independently with or without connecting plates or welding existing steel or iron surfaces complete all as specified.

Cutting holes into or through stone walls built in cement lime mortar and walls of cement concrete of superficial area exc 150 sqcm but n exc 400 sqcm and making good in CM 1:3 or cement concrete 1:2:4 type B-1 as required.

M&L for preparation of new plastered surface of wall and applying two coats of cement base paint complete all as specified and directed

S & F stainless steel sinks with drainage board made out of 1.00 mm thick sheet for kitchen with plugs, washers, waste pipes, including bedding in cement mortar to dwarf wall or including fixing cast iron cantilever brackets and connecting union to pipe overall size 915 mm x 460 mm with bowl size 410mm x 330mm x 160mm, with and including PVC waste pipe and CP waste coupling 32 mm dia and making good to disturbed surfaces, , complete all as specified.

S&F 0.90 mm thick Decorative laminate type I of surface finish,colour and pattern as approved,fixed with approved adhessive as per manufacturers instructions complete all as specified and directed by Engineer-in-Charge.

M&L ply wood, 6 mm thick,7 no of ply, grade BWR,type B B ,fixed with screws to timber frame work, complete all as specified and directed by Engineer-in-Charge.

S&F alluminium handles ,cast type anodised 100 mm size complete all as specified and directed by Engineer-in-Charge.

M&L second class hard wood wrough as in framed work complete all as specified and directed by Engineer-in-Charge.

S&F Ball catches with 8mm dia steel ball, and brass body and striking plate including letting in and fixed complete all as specified and directed by Engineer-in-Charge.

S&F Kitchen plate rack of stainless steel of silver colour ,1 mm thick of size 900mmx1200 mmx 250mm including fixing with screws complete all as spcified and as directed.

S&F One piece Vitreous china wash down water closet white or ivory colour approved equivalent as per specification complete set incl cistern with lid cover as per specification, including connection to waste pipe, flushing pipe, antisyphonage pipe etc and making good to floor complete all as specified and directed Make Cera, Hindware or equivalent in approved make.

S&F Toilet paper brass CP holder complete all as specified and as directed. Make: Model NL 55 make ESS ESS or equivalent in marc/ Jaquar/Prima.

S&F 15mm CP Two way bib tap to connect health faucet complete all as specified and directed

S&F Wash basins, vitreous china, white, flat back of size 630x450mm including brackets and cutting for and pinning in ends of brackets or erecting stand 32mm dia waste fittings, brass, chromium plated with long screwed shanks and fly nuts, 32mm dia HDPE waste pipe and including new brackets complete all as specified and as directed.

S&F 32 mm bore and 75cm long PVC waste pipe for WHB complete all as specified and as directed.

S&F 15 mm fancy type brass CP mixture for wash hand basin for mixing hot and cold water screwed down from iron pipe and fixed complete

S&F Acrylic shelf 46X13cm make ESS ESS model (TM 07) chrome or equivalent complete all as specified.

S&F corner shelf with CP railing 300mm x 300mm complete all as specified

S&F chromium plated brass shower rose 125 mm size with or witout swivel joints including fxing with 15 mm bore pipe, , complete all as specified and as directed.

S&F 15 mm fancy type brass CP mixer for wall for mixing hot and cold water screwed down from iron pipe and fixed complete

S&F fancy type bib taps, cast copper alloy, chromium plated, with crutch or butterfly handle, screwed down, screwed for 15 mm bore iron pipe or for brass ferrule ccomplete all as specified and as directed.

S & F soap dish brass chromium plated, fixed to plugs with brass chromium plated screws complete all as specified and directed by Engineer - in - Charge.

Excavation in trenches n exc 1.5m wide and exc 1.5m but n exc 3.0 m in depth for foundation etc in soft / loose soil complete all as specified and directed.

M&L for PCC 1:4:8 type D-2 (using 40mm graded crushed stone aggregate) as in foundation filling and mass concrete complete all as specified and directed.

S & F 75 mm bore PVC (SWR) floor trap with grating including jointing with solvent cement complete all as specified and as directed.

S & F 110 mm bore PVC (SWR) vent cowl complete all as specified.

Surface excavation not exceeding 30cm deep and averaging 15cm deep and getting out in loose / soft soil all as specified and directed by Engineer - in – Charge.

M&L for use and waste of form work to soffits of suspended slab such as roof slab, floor slab landings and similar work not exceeding 200 mm thick for finish complete all as specified and directed by EIC

M&L for use and waste form work to edges of concrete flats ,treads,breaks in floors window sillssides of rcc slabs exc 10 cm but not exc 20 cm etc rough finished surface of concrete complete all as specified and directed by EIC

M&L RCC 1 : 1 ½ : 3, Type A–1 using 20mm graded aggregates for slabs supported on walls, beams, columns and in shelves, the like all as specified and directed by Engineer - in - Charge .

M&L hard core of broken bricks aggregate of gauge not exc 63 mm deposited spread & leveled in layers not exc 15 cm thick watered and rammed to a true surface

M&L PCC 1:3:6 type C1 (20mm graded stone aggraded for plinth protection, 50 mm thick, all as specified and directed by Engineer - in - Charge.

M&L for screed bed or bedding layer of mortar 20mm thick on roof in cement mortar 1:3 with water proofing compound all as specifed .

Applying evenly a tack coat of industrial bitumin 85/25 at the rate of 1.20 kgper sqm including cleaning surface , all as specified and directed by Engineer - in - Charge.

Supply onlyLiquid water proofing compound.

Providing precast cement concrete 1:2:4, type B-0 louvers and jallies, 40mm thick (measured solid) including all mouldings set in cement mortar 1:4 all as specified and directed by Engineer - in - Charge.

S&F 15mm bore stop valve, cast copper alloy screwed down, high pressure, with crutch or butterfly handle, screwed both ends of iron pipe or for union and fixed all as specified and directed by Engineer - in – Charge.

S&F PVC (SWR) vent cowls for 75 mm bore, all as specified and directed by Engineer - in - Charge.

S&F 20mm bore stop valve, cast copper alloy screwed down, fancy type, high pressure, with crutch or butterfly handle, screwed both ends of iron pipe or for union and fixed all as specified and directed by Engineer - in – Charge.

M&L ball valves high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball with minimum weight 210 gm screwed for 20mm bore dia iron pipe supplied complete all as specified and as directed by Engineer-in-charge.

S&F 150mm long extruded alluminium alloy handles fabricated type anodized, all as specified and directed by Engineer - in - Charge.

Preparing new plastered or unplastered surfaces of walls and applying three coats of white wash complete all as specified and directed by Engineer - in - Charge.

S&F Vitreous China urinals, bowl type (back or corner wall type), complete including spreader and providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe. all as specified and directed by Engineer - in - Charge.

S&F First quality, Non skid ceramic coloured joint free tiles, 7 to 8 mm thick (square or rectangular) area of each tile exe 0.18 Sqm but n.exe 0.38 Sqm, laid in floors set and jointed with neat cement slurry @ 3.00 kg/Square Metre over and including 15 mm thick screed bed of cement mortar (1:4) including pointing in white cement with pigment to match the shade of tiles, complete all as specified.

Aluminium anodized window frame 100mmx44mmx1.6mm fixed with aluminium board and thurst bolt in walls by drilling as directed.(a) Aluminium anodized window shutter styles and rails 44mmx44mmx1.6mm(b) Aluminium anodized butt hinges 04 Nos in each window 75mm long ISI marked (c) Aluminium anodized tower bolt 200mmlong size Make Classic or Argent – 02 No in each shutter (d) Aluminium anodized cast type handles Make Classic or Argent – 01 No in each shutter(e) Aluminium anodized hook and eye 150mm long 01 no for each shutter Glass pane shall be 5.5mm thick tinted glass of size as required

Taking down old steel windows & S&F ECO-4000 Series windows/ventilators (Double rebate) fabricated from roll framed sections made of galvanized steel colour coated/powder coated ( Base steel as per IS 513"D" quality galvanized as per IS 277 with Zinc of 120gms/Sqr.mtr) with total coated thickness of 0.6mm and section of frame should be of 72mm x 55mm ,section for mullion should be of 72mm x 50mm, section for shutter frame should be of 47mm x 20mm, section for fixed glass bead should be of 12mm x 12mm and section for fly mesh should be of 40mm x 20mm, coated section should be with primer coat of Epoxy primer of 5-7 microns thick,finish painted with polyester paint of 12-16 microns thick or powder coated with pure polyester upto to 50-60 microns thick including 5mm thick plain glass, stainless steel 32 gauge fly mesh of 304 grades with 144 holes per square inch and Grill made of 10mm Sq MS bars welded to at 150mm centre to centre, 6mm x 12mm MS flat (total grill unit should be powder coated and fixed to window frame with screws). (a) FIXING DETAILS :- Section for frame Glazed shutters and Mesh shutters should be cut to length and miter joined with polypropylene corner brackets,mullion section should be joined with Frame/Mullion using Mullion Cap ethyl propylene damein monomer (EPDM) gasket should be used all around glass in shutter and fixed glass,rubber Gasket should be used around glass in shutter and fixed glass.Rubber gasket should be used around fly mesh to fix mesh in mesh shutter. (b) ACCESSORIES :- Each glazed shutter and mesh shutter should be provided with SS pivot hinges - 1 set, seccolor handle & seccolor stay. Window frame should be fixed to brick/concrete masonry by using Nylon self expanding caps and driving MS electroplated 80mm long screws into the caps through frame. Make :- NCL alltek and seccolor Ltd and Eqivalent.

Filling under floor including spreading levelling watering and well ramming in layers n exc 25 cm thick complete all as specified and directed

M&L for PCC 1:2:4, Type B-0 (using 12.5mm graded crushed stone aggrigate), 20mm thick as in DPC complete all as specified and directed.

M&L for factory made box type steel ventilator with glazing bars dovetailed or welded and with one shop coat of zinc chromate primer complete all as specified

Taking down carefully aluminum/copper point wiring (light/fan/socket/power) including fittings & fixtures such as switches, socket ceiling roses, pendants, regulators etc and removing unserviceable materials from site and making good disturbed surfaces of walls/floors and reuse the serviceable fittings under respective items complete.

M & L for point wiring with 1.5 Sq mm (Nominal area) PVC insulated and unsheathed 1.5 sq mm cable of 1100 Volt grade FRLS with stranded copper conductor in and including PVC conduit concealed type including continuous earth wire of 1.5 Sq mm FRLS PVC insulated, unsheathed stranded copper conductor cable and connected to common earth dolly with MS pressed steel terminal Modular boxes (taking in seperate items) with modular cover plate (taking in seperate item) complete with all accessories for one light point/Fan point/call bell point controlled by one ,one way switch complete all as speified and directed. Make : Havells/Polycab/KEI or equivalent in approved makes. Note : Cutting chases for conduits and sinkings for boxes and making good to walls, floors etc to match with existing shall deemed to be included in item rates quoted.

All as per item No 210.00 mentioned here-in- above but for one 3 pin 5 Amps socket out let on independent board with 1.5 sq mm PVC insulated and unsheathed copper conductor with 1.5 sq mm PVC insulated copper conductor single core for continuous earthing complete.

All as per item No 210.00 mentioned here-in- above but for one 3 pin 5 Amps socket out let on same board with 1.5 sq mm PVC insulated and unsheathed copper conductor with 1.5 sq mm PVC insulated copper conductor single core for continuous earthing complete.

All as per item No 210.00 mentioned here-in- before but for 3 pin15 Amps socket outlet on independent board with 2.5 sq mm PVC insulated and sheathed copper conductor with 2.5 sq mm PVC insulated copper conductor single core for continuous earthing complete.

All as per item No 210.00 mentioned here-in- before but with 4 sq mm PVC insulated and unsheathed copper conductor with 4 sq mm PVC insulated copper conductor single core for continuous earthing complete for AC point..

Supply and fixing single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB SP 20-32 Amps all as specified and directed.

M & L for Switch modular type single pole one way 6 Amp complete all as directed. Make : Havells/Anchor/ Legrand or equivalent in approved makes.

M & L for Socket outlet 2 in 1,3 pin , 6 Amps modular type complete all as directed. Make : Havells/Anchor/ Legrand or equivalent in approved makes.

M & L for Switch modular type single pole one way 15/16 Amp complete all as directed. Make : Havells/Anchor/ Legrand or equivalent in approved makes.

M & L for Socket outlet 2 in 1,3 pin ,16 Amps modular type complete all as directed. Make : Havells/Anchor/ Legrand or equivalent in approved makes.

M & L for modular white cover plate with frame, 3 module complete all as directed. Make : Havells/Anchor/ Legrand or equivalent in approved makes.

M & L for modular white cover plate with frame, 4 module complete all as directed. Make : Havells/Anchor/ Legrand or equivalent in approved makes.

M & L for modular white cover plate with frame, 8 module complete all as directed. Make : Havells/Anchor/ Legrand or equivalent in approved makes.

M & L for modular metal flush box, 3 module complete all as directed. Make : Havells/Anchor/ Legrand or equivalent in approved makes.

M & L for modular metal flush box, 4 module complete all as directed. Make : Havells/Anchor/ Legrand or equivalent in approved makes.

M & L for modular metal flush box, 8 module complete all as directed. Make : Havells/Anchor/ Legrand or equivalent in approved makes.

M & L for ceiling rose, surfaces Bakelite three terminals complete all as directed. Make : Anchor / Plaza or equivalent in approved makes.

M & L sheet metal enclosure for DBs 8 way double door type with 200 amps rated busbar SPN including necessary connection complete. Make : Havells/C&S/legrand/L&T or equivalent in approved makes.

M & L sheet metal enclosure for DBs 4 way double door type with 200 amps rated busbar TPN including necessary connection complete. Make : Havells/C&S/legrand/L&T or equivalent in approved makes.

M&L for MCB TPN 415 volts 63 Amps, rupturing capacity 10 KA, C series complete all as specified and as directed.Make Hager/GE/Seimens/ standard/Havells

M&L for MCB SPN 240 volts 32 Amps, rupturing capacity 10 KA, C series complete all as specified and as directed.

M&L for MCB SP volts 5-32 Amps, rupturing capacity 10 KA, C series complete all as specified and as directed.

M&L for wiring for submain wiring with two single core 4 sqmm (nominal area)FRLS insulated copper conductor multi stranded unseathed 1100 volts grade drawn through and including PVC concealed conduit including one 4 sqmm FRLSH insulated and unsheathed copper conductor cable as earth wire connected to common earth and dolly including ctting chases in wall with making good the distrubed surfaces with 1:3 cement mortor to match the existing. Note :- 02 Run of 4 sqmm cable, 01 run of 4 sqmm cable and 01 run of PVC conduit shall be measured as one unit.

M&L for wiring for submain wiring with two single core 6 sqmm (nominal area)FRLS insulated copper conductor multi stranded unseathed 1100 volts grade drawn through and including PVC concealed conduit including one 6 sqmm FRLSH insulated and unsheathed copper conductor cable as earth wire connected to common earth and dolly including ctting chases in wall with making good the distrubed surfaces with 1:3 cement mortor to match the existing. Note :- 02 Run of 6 sqmm cable, 01Run of 06 sqmm cable and 01 run of PVC conduit shall be measured as one unit.

Supply, laying and testing in duct, along wall or passing through pipe 1100 volts grade, heavy duty XLPE insulated, screened, PVC bedded galvanized steel strip armoured heavy duty electric cable with aluminium conductor cross sectional area 400 Sqmm 3.5 core complete all as specified. (i) Note :- Laying of cable in duct, along wall in pipe include pipe clamp nuts bolts, removing and refixing of duct cover included in item rates. GI pipe shall be measured and paid separately under relevant item.

Complete all as per item No 234.00 here-in-before but of 35 sqmm 3.5 core

M&L 100 mm bore steel for tubing light grade ISI marked with all fitting and fixed complete to walls and ceiling or laid in floors for protection of cable including necessary joint complete all as specified and as directed. (Make TATA/JINDAL/BANSAL).

complete all as item 236.00 here-in-before but for 40 mm dia

M&L for making opening on the surface PCC pavement hard surface of road etc for embedding light grade GI pipe. The depth of the GI pipe shall not be less than 200 mm from surface. The opening made on surface/PCC shall be properly sealed matching the existing surface with suitable grade PCC/bitumen mix/epoxy and clear debris omplete all as specified and directed.

S&F exhaust fan PVC louvre heavy duty 300 mm sweep 950 RPM, 230 Volts A/C, including connection complete (Not less than 3 star rating)

S & F 01x 20W LED tube light fittings having CCT 5700K, 220 to 240 volts with ploycarbonate/extruded aluminium alloy/powder coated CRCA sheet, connector block etc complete with all accessories internally prewired and including connecting up with twin core twisted flexible copper conductor cable with suitable size complete all as specified and directed. Make : Havells Cat No. LUMILINEBS20WLED865SPCWH or equivalant in approved makes.

S & F 2'x2' grid ceiling fitting with ultra modern designed architectural 2'x2' 28 watt LED luminaire which provide soft light and glare free symmetrical illumination suitable for armstrong/grid ceiling, intergrated electronic driver etc complete with all accessories internally prewired and including connecting up with twin core twisted flexible copper conductor cable with suitable size complete all as specified and directed. Make : Havells Cat No. LHEWEIP7PW1W028 or equivalant in approved makes.

Supply and fix air curtain in 3 speed aluminium body with powder coated chasis operate by remote control for comercial application size 6 feets 220 volts 50 Hz with virgin plastic MOC blower including all accessories with necessary fittings all as specified and as directed. Note : 1000 days warranty period. Make Mitzvah or equivalent model/make in approved makes.

Supply, install, testing and commissioning cubical type CPRI approved dust and vermin proof factory made LT panel board indoor type of suitable size free standing made out of 2 mm thick CRCA sheet for door and covers and sheet shrouds and partitions shall be minimum 1.6 mm dust and vermin proof, front opening (double shutter) with locking arrangement from front and rear both duly fitted with 600 Amps rated aluminium bus bar 4 strip covered with colour coded FRP with compression cable glands for entry & exit of cables, powder coated complete and supply & comprising of the following including internal pre-wiring complete:- (A) INCOMING:- (i) MCCB 400 Amps, capacity 36 KA, 4 poles, 415 Volts, 3 phase (Adjustable thermal type & fixed magnetic setting) - 01 No. (ii) Indicator lamp neon/ LED type RBY -01 Set of three.

M&L for one light/fan/exhaust fan point wiring controlled by one switch with PVC insulated unsheathed multi stranded copper conductor (FRLS) of size 1.5 Sqmm (for Phase colour code Red and for Neutral colour code Black) and one run of size 1.5 Sqmm PVC insulated unsheathed multi stranded copper conductor (FRLS) (as earth wire, colour code green) and connected to common earth dolly all as specified. , drawn through in and including concealed PVC Conduit medium grade, ISI marked 25 mm dia along with conduit fixing accessories with MS terminal boxes (not less than 1.6 mm thick) and painted with one coat of red oxide primer all around and two coats of black bituminous paint from out side and two coat of aluminum paint from in side including earth dolly with 3 mm thick plastic laminated sheet top cover of approved make and colour and for provision of switches/regulators as per specified SSR and as directed by Engineer- in- Charge. NOTE:-After rewiring cutting chasing portion should be matched with existing finish of walls. MAKE-1.Havells, 2.polycab, 3.gloster or equivalent in approved makes

All as per item No 245.00 above but 5 Amp socket outlet, independent.

All as per item No 245.00 above but on the same board.

All as per item No 245.00 above but 2.5 sq mm wire for one 15 Amps socket outlet independent with continuous PVC insulated single core green colour copper earth wire of size 1.5 sq mm connected to common earth dolly.

All as per item No 245.00 mentioned here-in- before but with 4 sq mm PVC insulated and unsheathed copper conductor with 4 sq mm PVC insulated copper conductor single core for continuous earthing complete for AC point..

S&F switch piano in replacement flush button type 5 Amp single pole one way complete all as specified and as directed. Make:- Anchor/cona/ssk or equivalent in approved makes.

S&F switch piano flush button type 15 Amp single pole one way complete all as specified and as directed. Make:- Anchor/cona/ssk or equivalent in approved makes.

S&F socket outlet 2in1, 3 pin, 5 Amp and 15 Amp flush type complete all as specified and as directed. Make:- Anchor/cona/ssk or equivalent in approved makes.

S&F socket outlet 2in1, 3 pin, 5 Amp flush type complete all as specified and as directed. Make:- Anchor/cona/ssk or equivalent in approved makes.

S&F in replacement of electronic fan regulator 450 watt complete all as specified and directed.

S & F in repair with MCB TPN 32 amps 10 KA ,c-series including connection with suitable size aluminium / copper lugs complete all as specified and directed . Make - Legrand / Havells/ L & T or equivalent in approved makes.

S & F with MCB TPN 40 to 63 amps 10 KA ,B-series including connection with suitable size aluminium / copper lugs complete all as specified and directed .

Supply and fixing Earthing with galvanised steel earth plate electrode 60cm x 60cm x 6mm thick, buried directly in ground (earth pit not less than 2.25m below normal ground level) with top edge of earth plate not less than 1.5m below normal ground level connected to main earth lead 32 x 6 mm galvanised iron strip by means of bolts, nut, check nuts and washers of galvanized iron or steel all as shown in electrical plate No.3 of MES Schedule pt-I 2009, GI earth lead strip protected by GI pipe 40 mm dia light grade and connected to earth test point including excavation in any type of soil,returning filling, disposal of soil, providing charcoal dust and common salt upto top edge of earth plate, construction of PCC pit with RCC cover, funnel, watering pipe of 20mm dia GI light grade and provision of earth test point including testing on completion complete all as specified and as directed.

Supply , laying & testing in replacement for XLPE insulated, armoured, heavy duty electric cable with stranded aluminium conductor, 1100 volts grade, laid in trenches, sleeving through pipes or fixed on poles & walls or laid under floors including jointing with suitable size aluminium lugs complete of size 25 Sqmm 3.5 core complete all as specified and directed.

Excavation in trenches, not exc 1.5 m wide and n exc 1.5 m in depth for under ground cable & foundation of poles , stay assembly and depth and getting in any type of soil complete all as specified and directed .

Returning, filling of hard and dense soil in including spreading , leveling , watering and well ramming in layers n. exc. 25 cm complete all as specified and directed .

Removing excavated soft / disintegrated soil to a distance n.exc 50 m and depositing where directed at a level n.exc. 1.5 m above the starting point complete all as specified and directed .

Removing excavated soils, exc 250 & n exc 500m and depositing where directed at a level n.exc.1.5 m above the starting point complete all as directed.

M & L sand cushioning to underground cables in layer ( 8 cm thick before laying of cables and 15cm thick after laying and stretching of cable ) in trenches for cable protection or under floor or in foundation complete all as specifed and directed . Note- Sand thickness shall be measured 18 cm only.

M & L for old size sub class 'B' bricks locally available best quality to be laid in trenches as protection of cable complete all as specified and directed .

Taking down carefully MCB DBs including MCB and connected items and making good disturbed surfaces of wall , floor etc and matching wth original colour of wall, complete, all as specified & directed

Complete all as per item No 245.00 here-in-before One bell/buzzer point controlled by one bell push.

S&F bell push flush type 5 amp one way ISI Marked complete all as specified and directed. Make:- Anchor/cona/ssk or equivalent in approved makes.

S&F Bell, DING DONG AC 230 Volts single pole type complete all as specified and as directed. Make:- Anchor/cona/ssk or equivalent in approved makes.

S&F enviroment friendly indoor decorative 10 Watt LED mirror light polycarbonate Batten with opal diffuser including all accessaries all as specified and directed. Make:- 1. Havells Cat No LUMILINEPLUSBS10WLED865SPCSS or equivalent in Halonix and Philips or equivalent in approved makes.

Supply & fix exhaust fans heavy duty 300 mm dia 1400 RPM, 50 Hz 230 volt for domestic use,dynamically balance blade , epoxy powder coated confirm to IS 2312-1967 with ISI marking IP-55 with class B insulation motor including suitable size louver and all fixing accessories such as fastners nut bolts and electric connection with 3 core cable complete all as specified and directed. Make -Havells/crompton/ bajaj or equivalent in approved makes.

Supply & fix metallic body storage type geyser of capacity 25 Ltrs 2000 watt 230 V,1 Phase,50 Hz AC with minimum 4 star BEE rating and tank made of ultra thick super cold rolled steel plates and viterous enamel coated with heavy duty magnesium anode including all accessories comlete all as specified and directed. Make- Havells ,Bajaj , crompton or equivalent in approved makes.

S&F of enviroment friendly indoor decorative type wall mounting ,brushed nickel finish fixture with opal glass diffuser with 9 Watt retrofit LED lamp B22 base made up of polycarbonate including all accessaries all as specified and directed. Make:- 1. Havells Cat No LHFOAJE1TZ1I060, equivalent in Philips and Halonix & approved makes.

M & L for Lamp holder with insulated body, with back plate suitable for batten fittings complete all as directed. Make : Anchor / Plaza or equivalent in approved makes.

S&F LED Lamp 9 watt ISI marked with valid CML. Make Havells, Philips or equivalent in Approved makes

Supply and fixing decorative wall LED light fitting (sub type city 2) suitable for 1x15 watt made up of polycorbonate housing with B22 base prewired with twin core twisted flexible copper conductor wire with LED lamp .complete all as directed. Make : Havells cat Part LHDL03160099 or equivalant in aproved makes.

Supply & fix ceiling fans complete with electronic type regulator and accessories 230 V,1200 mm sweep BEE 5 star rated complete all as specified and directed.

Net Contract Sum will be after deducting Sch of Credit of Rs 1,25,811.00

Ish Engineers and Contractors