Provision of Civil Works for Automotive and Weapon System Testing Center at CVRDE Chennai

Amount

SUBHEAD-I : EARTH WORK EXCAVATION

Earth work in Excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.

All kinds of soil.

Excavation work by mechanical means (Hydraulic excavator)/ manual means in foundation trenches or drains (not exceeding 1.5m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soils as directed, within a lead of 50 m.

Ordinary Rock

Hard Rock (Blasting prohibited)

Earth work in excavation by mechanical means (Hydraulic excavator) /manual means over areas (exceeding 30cm in depth. 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth, lead upto 50m and lift upto 1.5m, disposed earth to be levelled and neatly dressed.

All kinds of soil.

Excavation work by mechanical means (Hydraulic excavator)/ manual means in over areas ( exceeding 1.5m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soils as directed, within a lead of 50 m.

Ordinary Rock

Hard Rock (Blasting prohibited)

Extra for every Additional Lift of 1.5 m or part there of in excavation / banking excavated or stacked materials.

All kinds of soil

Ordinary or hard rock

Filling Available Excavated Earth (Excluding Rock) in trenches,Plinth sides of foundatios etc,in layers not exceeding 20cm in depth consolidating each diposited layer by ramming and watering,lead upto 50meter and lift upto 1.5meter (10% shall be deducted for voids to arrive at the net quantity for payment)

Supplying and filling of earth obtained from out side MoD land (including royalty) by mechanical transport upto a lead of 10 km and filling in layers not exceeding 20 cm in depth, breaking clods, watering, rolling each layer with ½ tonne roller, or wooden or steel rammers, and rolling every 3rd and top-most layer with power roller of minimum 8 tonnes and dressing up, in embankments for roads, flood banks, marginal banks, and guide banks etc., lead upto 50 m and lift upto 1.5 m : (5% shall be deducted for voids to arrive at the net quantity for payment)

Felling trees of the girth (measured at a height of 1 m above ground level), including cutting of trunks and branches, removing the roots and stacking of serviceable material and disposal of unserviceable material.

Beyond 30 cm girth upto and including 60 cm girth

Beyond 60 cm girth upto and including 120 cm girth

Beyond 120 cm girth upto and including 240 cm girth

Above 240 cm girth

SUB HEAD II : ANTI TERMITE TREATMENT

Supplying Chemical Emulsion in sealed containers including delivery as specified.

Chlorpyriphos/ Lindane emulsifiable concentrate of 20%

Diluting and Injecting Chemical Emulsion for POST-CONSTRUCTIONAL anti-termite treatment (excluding the cost of chemical emulsion) :

Along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc.

With Chlorpyriphos/ Lindane E.C. 20% with 1% concentration.

Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1 cement : 2 Coarse sand) to match the existing floor :

With Chlorpyriphos/ Lindane E.C. 20% with 1% concentration.

SUB HEAD III : PLAIN AND REINFORCED CEMENT CONCRETE WORK

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level

1:4:8 (1 Cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size)

Providing and laying cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) in, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor, etc. up to floor five level, excluding the cost of centering, shuttering and finishing.

Making Plinth Protection 50mm thick of Cement Concrete 1:3:6 (1 cement :3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand including finishing the top smooth.

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Ordinary Portland cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 1.10 times of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement.

All works upto plinth level.

Concrete of M25 grade with minimum cement content of 330 kg /cum

Concrete of M30 grade with minimum cement content of 350 kg /cum

All works above plinth level upto floor V level.

Concrete of M25 grade with minimum cement content of 330 kg /cum

Concrete of M30 grade with minimum cement content of 350 kg /cum

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and manufactured sand (i.e.Robo sand) as fine aggregate, Ordinary Portland cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 1.10 times of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement.

All works upto plinth level.

Concrete of M25 grade with minimum cement content of 330 kg /cum

Concrete of M30 grade with minimum cement content of 350 kg /cum

All works above plinth level upto floor V level.

Concrete of M25 grade with minimum cement content of 330 kg /cum

Concrete of M30 grade with minimum cement content of 350 kg /cum

Add for using extra cement in the items of design mix over and above the specified cement content there in.

Supplying fabricating and fixing in position Reinforcement Steel for RCC work at all levels and locations including the cost of steel, straightening, cutting,bending,binding and placing in position etc.,as per drawings and specifications including the cost of binding wire labour etc., complete for reinforced concrete. .

Thermo-Mechanically Treated bars of grade Fe-500D or more.upto plinth level.

Thermo-Mechanically Treated bars of grade Fe-500D or more.above plinth level. Upto floor V level.

Centering and Shuttering including strutting, propping etc. and removal of form for :

Foundations, footings, bases of columns, etc. for mass concrete.

Suspended floors, roofs, landings, balconies and access platform.

Lintels, beams, plinth beams, girders, bressumers and cantilevers.

Columns, Pillars, Piers, Abutments, Posts and Struts.

Stairs, (excluding landings) except spiral-staircases

Walls (any thickness) including attached pilasters, butteresses,plinth and string courses etc.

Weather shade, Chajjas, corbels etc., including edges

Small surfaces such as cantilever ends, brackets and ends of steps, caps and bases to pilasters and columns and the like

Extra for additional height in centering, shuttering where ever required with adequate bracing, propping etc., including cost of de-shuttering and decentering at all levels, over a height of 3.5 m, for every additional height of 1 metre or part thereof (Plan area to be measured).

Suspended floors, roofs, landing, beams and balconies (Plan area to be measured)

SUB HEAD IV: STRUCTURAL STEEL WORK

Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and providing & painting with two coats of synthetic enamel paint of approved colour to achieve even shade over and including a priming coat of approved steel primer etc all complete .

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete

Hot finished welded type tubes

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.

In stringers, treads, landings etc. of stair cases, including use of chequered plate wherever required, all complete

In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works

SUB HEAD V: STONE WORK & BRICK WORK

Random Rubble Masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) upto plinth level with :

Cement mortar 1:6 (1 cement : 6 coarse sand).

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 3.5 in foundations upto plinth level in all shapes and sizes in :

Cement mortar 1:6 (1 cement : 6 coarse sand).

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 3.5 in superstructure above plinth level up to floor V level in all shapes and sizes in :

Cement mortar 1:6 (1 cement : 6 coarse sand).

Providing and laying autoclaved aerated cement blocks masonry with 150mm/230mm/300 mm thick AAC blocks in super structure above plinth level up to floor V level with RCC band at sill level and lintel level with approved block laying polymer modified adhesive mortar all complete as per direction of Engineer-in-Charge. (The payment of RCC band and reinforcement shall be made for seperately).

Providing and laying autoclaved aerated cement blocks masonry with 100 mm thick AAC blocks in super structure above plinth level up to floor V level in cement mortar 1:4 (1 cement : 4 coarse sand ). The rate includes providing and placing in position 2 Nos 6 mm dia M.S. bars at every third course of masonry work.

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 3.5 in superstructure above plinth level up to floor V level.

Cement mortar 1:4 (1 cement : 4 coarse sand).

Extra for providing and placing in position 2 Nos 6mm dia. M.S. Bars at every third course of half brick masonry.

SUB HEAD VI: PLASTERING & SURFACE TREATMENT

6 mm Thick Plastering in cement mortar 1:3 (1 cement: 3 coarse sand) at all levels and locations for all concrete surfaces of columns, beams,walls, and slabs finished smooth and even etc., complete.

Providing and applying 12 mm cement plaster of mix :

1:6 (1 cement: 6 coarse sand)

Providing and applying 15 mm cement plaster on rough side of single or half brick wall of mix:

1:6 (1 cement: 6 coarse sand)

18 mm cement plaster in two coats under layer 12 mm thick cement plaster 1:5 (1 cement : 5 coarse sand) and a top layer 6 mm thick cement plaster 1:3 (1 cement : 3 coarse sand) finished rough with sponge.

Cement plaster 1:3 (1 cement: 3 coarse sand) finished with a floating coat of neat cement.

12 mm cement plaster

Extra for providing and mixing water proofing material in cement plaster work in proportion recommended by the manufacturers.

Providing and fixing Chicken wire Mesh 22 Guage of approved make with all necessary hard ware at the junction of RCC and brick work with required overlapping as directed by Engineer-in Charge etc., complete.

White Washing with lime on new walls and ceiling three coats to give an even shade including preparation of surface etc.,complete as directed.

Providing and applying white cement based putty of average thickness 1 mm,of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Providing and Applying Two coats of oil bound distemper of approved brand and shade over and including one coat of primer, including preparation of surface etc.,complete as directed.

Wall painting with acrylic emulsion paint, having VOC (Volatile Organic Compound) content less than 50 grams/ litre, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour.

Two coats

Finishing walls with textured exterior paint of required shade :New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @ 2.20kg/10 sqm

Finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)

Providing and applying Two coats of synthetic enamel paint of approved brand and shade over a coat of primer including preparation of surface and applying approved brand putty on following surfaces at all levels and locations etc., complete.

Steel surfaces with zinc chromate primer.

Wooden Surfaces

SUB HEAD VII: FLOORING

Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), including pointing the joints with white cement and matching pigment etc., complete.

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineerin- Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete.

Size of Tile 600x600 mm

Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/sqm including grouting the joint with white cement & matching pigments etc. complete.

Size of Tile 600x600 mm

Providing and laying flamed finish Granite stone in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge

Granite stone slab Jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent.

Providing and laying flamed finish Granite stone flooring for treads, landings or similar locations of required size and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge :

Flamed finish granite stone slab Jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent.

Providing and laying Polished Granite Stone work for skirting, risers of steps over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 Coarse sand) and cement slurry @ 3.3 kg/sqm including pointing in white cement complete.

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.

a) Granite of ay colour and shade, area of slab over 0.50 sqm

Extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform, vanity counter and similar location in marble/ Granite/ stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete.

Providing and fixing stone slab with table rubbed, edges rounded and polished of size 75x50 cm deep and 1.8 cm thick, fixed in urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 6 mm nominal size) as per direction of Engineer-incharge and finished smooth.

a) White Agaria marble stone

Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete.

40 mm thick with 20 mm nominal size stone aggregate

52 mm thick cement concrete flooring with concrete hardener topping, under layer 40 mm thick cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) and top layer 12 mm thick cement hardener consisting of mix 1:2 (1 cement hardener mix : 2 graded stone aggregate 6 mm nominal size) by volume, ardening compound mixed @ 2 litre per 50 kg of cement or as per manufacturer's specifications. This includes cost of cement slurry, but excluding the cost of nosing of steps etc. complete.

Providing and fixing PVC sheet flooring of approved make, of thickness 2mm with the size of roll upto 2m x 20m . The product shall be homogeneous and single layered with PUR range. The wear surface shall consist of impregnated polyurethane homogeneous mixture of PVC with ‘ Diamond 10 ’ technology, Plasticizers without DOP, Urethane, color pigments and filler calendared to form a sheet. Color and pattern details shall be dispersed throughout the thickness of the wear layer. It shall conform to group "T" wear resistance as per EN 649, Clean Room certified with class 'A' as per ASTMF5100, Flammability resistance of class Bfl-s1 as per GB8624-2006, Dynamic coefficient of friction of class DS as per EN 13893, Thermal Resistance of 0.072m2K/W as per EN 12667,

Thermal conductivity of 0.071W/mK as per EN12524, impact sound reduction of 3dB as per ISO 10140, Slip Resistance of class R9 as per DIN 51130, Residual indentation of 0.03mm as per GB/T 4085-2005, Color fastness rating of ≥6 as per ISO 105-B02, total weight being 2.8kg/m2 as per EN430. The product shall be suitable for applications in class 23/34/43 areas as per EN685. Product shall exhibit antistatic behaviour, resistance to bacteria, resistance to chemical, resistance to staining, suitability to castor chair. The product shall be Floor Score certified with no SVHC content published by European Chemicals Agency (REACH). Product shall contribute to LEED points under Indoor environmental quality category.

The PVC sheets shall be installed at site which includes preparing the surface, cleaning as required and applying adhesive - as recommended by the P.V.C tile manufacturer, laying, aligning, cutting in required size and pattern, trimming of tiles, removing the adhesive stains on the surface including cleaning the surface with soap solution (2 table spoons of soap powder for 5 Ltr of water) using a cloth or mop or and wiping the dried surface with soft dry cloth etc; complete all as per specifications and as directed by Engineer-In-Charge.

Providing and laying Ceramic glazed floor tiles of size 400 x 400 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), including pointing the joints with white cement and matching pigment etc., complete.

Providing and laying Ceramic glazed floor tiles of size 400 x 400 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 12 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), including pointing the joints with white cement and matching pigment etc., complete for skirting.

Providing and laying 60mm thick faciory made cement concrete interlocking paver block of M -30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50mm thick compacted bed of coarse sand, filling the joints with line sand etc. all complete as per the direction of Engineer-in-charge.

Providing and laying C.C. pavement of mix M-30 with ready mixed concrete from batching plant. The ready mixed concrete shall be laid and finished with screed board vibrator , vacuum dewatering process and finally finished by floating, brooming with wire brush etc. complete as per specifications and directions of Engineer-in-charge. (The panel shuttering work shall be paid for separately). (Note:- Cement content considered in this item is @ 350 kg/cum. Excess/less cement used as per design mix is payable/ recoverable separately).

Cement plaster skirting up to 30 cm height, with cement mortar 1:3 (1 cement : 3 Coarse sand), finished with a floating coat of neat cement.

18 mm thick

Providing and fixing Joint Filler board in Expansion joints

Making grooves of 5mm wide and 12mm deep in VDF flooring with mechanical cutter and filling and sealing the same with polysulphide sealant of approved make through an authorized applicator as per the requirements including all material, labour etc., complete.

SUB HEAD VIII : STEEL AND WOOD WORKS

Providing and fixing T-iron frames for windows and ventilators of mild steel Tee-sections, joints mitred and welded, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer.

Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size).

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing /paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately

For fixed portion :

Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15)

Powder coated aluminium (minimum thickness of powder coating 50 micron)

For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber /neoprene gasket required (Fittings shall be paid for separately)

Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15)

Powder coated aluminium (minimum thickness of powder coating 50 micron)

Filling the gap in between aluminium frame & adjacent RCC/ Brick/ Stone work by providing weather silicon sealant over backer rod of approved quality as per architectural drawings and direction of Engineer-in-charge complete.

Upto 5mm depth and 5 mm width

Providing & fixing fly proof wire gauze to windows, clerestory windows & doors with M.S. Flat 15x3 mm and nuts & bolts complete.

Stainless steel (Grade 304) wire gauge of 0.5 mm dia wire and 1.4 mm aparture on both sides

Providing and fixing 2.5mm thick M.S. sheet door with frame of 40x40x6 mm angle iron and 3 mm M.S. gusset plates at the junctions and corners, all necessary fittings complete, including applying a priming coat of approved steel primer.

Using M.S. angels 40x40x6 mm for diagonal braces

Providing and fixing pressed steel door frames conforming to IS: 4351, manufactured from commercial mild steel sheet of 1.60 mm thickness, including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25 mm, or base ties of 1.60 mm, pressed mild steel welded or rigidly fixed together by mechanical means, including M.S. pressed butt hinges 2.5 mm thick with mortar guards, lock strike-plate and shock absorbers as specified including fixing with adjustable lugs with split end tail to Each jamb and filling in the frame cement concrete 1:3:6 by using 20mm and down graded metal complete, applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer-in-charge:

(Profile E) Fixing with adjustable lugs with split end tail to each jamb

(Profile C) Fixing with adjustable lugs with split end tail to each jamb

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters:

35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISi, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete.

Providing and fixing Glazing in Window, ventilator shutters etc., with EPDM/neoprene gasket etc.,complete as per the architectural drawings and the directions of Engineer-in-charge(Cost of aluminium snap beading shall be paid in basic item).

With float glass panes of 4.0 mm thickness (weight not less than 10.0 kg / sqm)

With float glass panes of 5.0 mm thickness (weight not less than 12.5 kg / sqm)

With float glass panes of 6.0 mm thickness (weight not less than 15 kg / sqm)

With float etched glass panes of 6.0 mm thickness (weight not less than 15.0 kg / sqm) in partitions.

Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of Engineer-in- charge.

Pre-laminated particle board with decorative lamination on both sides

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete.

Fixed to openings / wooden frames with rawl plugs, screws etc,

Providing and fixing Fiber Glass Reinforced plastic (FRP) Door Frames of cross-section 90mm x 45mm having single rebate of 32mm x 15mm to receive shutter of 30mm thickness .The laminate shall be moulded with fire resistant grade unsaturated polyester resin and chopped mat . Door frame laminate shall be 2mm thick and shall be filled with suitable wooden block in all the three legs. The frame shall be covered with fiber glass from all sides. M.S. stay shall be provided at the bottom to steady the frame.

Providing and fixing 30 mm thick Glass Fibre Reinforced Plastic (FRP) panelled door shutter of required colour and approved brand and manufacture, made with fire - retardant grade unsaturated polyester resin, moulded to 3 mm thick FRP laminate for forming hollow rails and styles, with wooden frame and suitable blocks of seasoned wood inside at required places for fixing of fittings, cast monolithically with 5mm thick FRP laminate for panels conforming to IS: 14856 including fixing to frames.

Providing and fixing the following hardware fittings of approved make.

Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete

125mm long handles.

Rubber cleats of 50mm size

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete.

Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete.

Twin rubber stopper

Providing and fixing aluminium sliding door bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with nuts and screws etc. complete.

Providing and fixing stainless steel (Grade 304) Railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

Providing and fixing wire gauge shutters using stainless steel grade 304 wire gauge with wire of dia 0.5 mm and average width of aperture 1.4 mm in both directions for doors, windows and clerestory windows with necessary screws:

35 mm thick shutters with ISI marked Stainless steel butt Sqm 20 hinges of required size, second class teak wood

Providing and fixing bright finished brass 100 mm mortice latch and lock, ISI marked with six levers and a pair of anodised (anodic coating not less than grade AC 10 as per IS : 1868) aluminium lever handles of approved quality with necessary screws etc. complete

Providing and fixing motorised rolling shutter with CE certified CRS gear, indirect drive operator of model no RS78GS of Gandhi Automation or approved equivalent make, curtain made from single skinned galvalume steel laths with natural finish of 1.0mm thickness and weighing not less than 13kg/sqm, shall be supported on mild steel brackets coated with grey epoxy primer by spray, shaft shall be manufactured from mild steel tube of suitable outside diameter and wall thickness to suit the shutter application. Side guides shall be made of 2.0mm thick heavy duty TG galvanised steel finished with a coat of grey epoxy primer by spray. Pressed galvalume steel hood box and motor cover shall be provided complete with reinforced bracket as required to suit the shutter width. Bottom profile shall be bend resistant double skinned extruded aluminium profile for additional strength.

Rolling Shutter of Size 5.0m (w) x 5.0m (h)

Providing and fixing 12 mm thick frameless toughened glass double shutter door of approved brand and manufacture, including providing and fixing complete hardware and floor spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-in-charge. Door hardware shall comprise of Standard top patch fitting of Dormakaba model no PT 20 - 2 nos, Standard bottom patch fitting of Dormakaba model no PT 10 - 2 nos, Standard top pivot of Dormakaba model no PT 24 - 2 nos, Standard lock with strike plate & EPC of Dormakaba model no US 10 - 2 nos, Pull handle of length 450mm and 25mm dia made of SS 304 grade of Dormakaba model no : TGDI-H450, back to back with 350mm CTC - 2 pairs, Floor spring with standard spindle and cover plate of Dormakaba model no :BTS 75V EN 1-4 - 2 nos, Floor stop half dome in satin Chrome, 45mm dia of Dormakaba model no : 3108 - 4 nos

SUB HEAD IX : ROOF WORK

Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete.

Terrace water proofing

Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations:

a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300 mm height including cleaning the surface before treatment

b) Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5 coarse sand ) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs

c) After two days of proper curing applying a second coat of cement slurry using 2.75 kg/ sqm of cement admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge.

d) Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement :4 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3 mm deep.

e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test. All above operations to be done in order and as directed and specified by the Engineer-in-Charge

With average thickness of 120 mm and minimum thickness at khurra as 65 mm.

Providing and applying of swellable type water stop tape, 19mm x 25mm thick in linear metre (expansive nature) for construction joints treatment of RCC structure, such as raft slab, retaining walls, water storage tank and at the junctions of raft slab with the retaining walls etc.. After cleaning the surface, one coat of required primer for swellable water stop tape shall be applied throughout the length of the joint @3.78 litre per 240 running metre. Over the primed surface swellable type water stop tape shall be placed. The work shall be carried out all complete as per specification and the direction of the engineer-in-charge. The product performance shall carry guaranteed for 10 years against any leakage.

Grading roof for water proofing treatment with

Cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size)

Surface preparation by cleaning to remove dust, oil, greace, laitance, etc., providing fillet of 100 mm radius at the intersection of roof slab and parapet wall, pipe pedestal etc., providing and applying cement slurry bonding coat sika latex or equivalent and approved water proofing treatment by providing and applying two coats of acrylic based elastomeric, crack bridging water proofing coating on the roof slab, gutter area, parapet wall, gutter wall pedestals etc., in the following sequences etc., in the following sequence etc, complete all as per approved manufacturer’s specifications. (i) Sika Toseal 107 or approved equivalent first coat @ 1.5 kg/Sqm. (ii) Intermediate reinforcement layer of Sika Fab 1 or approved equivalent. (iii) Second coat of sika reinforcement layer of Sika Topseal 107 or approved equivalent @ 1.5 Kg/Sqm. Providing 50 mm thick (average) protection, layer of screed concrete of 1:2:4, mixed using 10 mm down size aggregate admixed with IS 2645 integral water proofing compound plastocrete plus or approved equivalent @ 130 ml per bag of cement. The screed shall be applied in required slope. Making saw cut joints of 6 x10 mm on the protection screed at every 4m intervals in both directions to prevent drying and hardened shrinkage cracking, filling the joints with flexible, UV resistant two component pourable grade PU Sealant, Sika lg or 1h or equivalent etc., complete all as directed.

Wet areas Waterproofing Providing and applying two component acrylic polymer modified cementitious flexible waterproofing (BASF / Sika / Fosroc / MYK Arment) of approved brand over wet areas . The system shall include base preparation of cleaning, brushing and removal of flacky materials, grouting the porous area with cementitious grout, proper coving between slab and wall junctions and applying water proof material in two coats @ 0.75kg/M2/coat. Coating shall be done on the entire horizontal surface. and shall be continued vertically 300 mm above the wall level,etc., complete as per manufacturer's methodology and specification.(Plan area only shall be measured for payment.)

Providing and fixing 'B' Class GI spouts including making good the holes etc., complete.

50mm dia

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, including all specials such as coupler, shoe(plain), bends, single tee without door etc complete. (i) Single socketed pipes.

110mm dia

150mm dia

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm

interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with :

12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) :2011 (Board with BIS certification marks)

Providing and fixing mineral fibre false ceiling tiles at all heights of size 595X595mm of approved texture, design and pattern. The tiles should have Humidity Resistance (RH) of 99%, Light Reflectance ? 85%, Thermal Conductivity k = 0.052 - 0.057 w/m K, Fire Performance as per (BS 476 pt - 6 &7)in true horizontal level suspended on interlocking T-Grid of hot dipped all round galvanized iron section of 0.33 mm thick (galvanized @120 gsm) comprising of main T runners of 15x32 mm of length 3000 mm, cross T of size 15x32mm of length 1200 mm and secondary intermediate cross T of size 15x32 mm of length 600 mm to form grid module of size 600x600 mm suspended from ceiling using galvanized mild steel item (galvanised@80gsm) 50 mm long 8mm outer diameter M-6 dash fasteners, 6 mm diameter fully threaded hanger rod up to 1000 mm length and L-shape level adjuster of size 85x25x2 mm, spaced at 1200 mm centre to centre along main ‘T’. The system should rest on periphery walls /partitions with the help of GI perimeter wall angle of size24x24X3000 mm made of 0.40 mm thick sheet, to be fixed to the wall with help of plastic rawl plug at 450 mm centre to centre & 40 mm long dry wall S.S. screws. The exposed bottom portion of all T-sections used in false ceiling support system shall be pre-painted with polyester baked paint, for all heights. The work shall be carried out as per specifications, drawings and as per directions of the engineer-in-charge.

With 20 mm thick beveled tegular mineral fibre false ceiling tile (NRC 0.7)

Subhead - X : PEB

Supplying, fabricating, transporting to site and erecting Primary structural members like transverse rigid frames,columns, rafters, bracing members, canopy rafters, bearing frame rafters , rod and angle bracings etc., of approved make . All members shall be fabricated from plate or bar stock and shall have flanges and webs joined on one side of the web by a continuous welding process and shall conform to the physical specifications of ASTM A570 (Grade 50) or equivalent and having a minimum yield strength of 50,000 P.S.I. (345 MPa). Rod and angle bracing shall conform to the physical specifications of ASTM A36 (or equivalent) and having a minimum yield strength of 36,000 P.S.I. (250 MPa).Members fabricated from hot rolled structural shapes shall conform to the physical specifications of ASTM A572 (Grade 36) or equivalent and having a minimum yield strength of 36,000 P.S.I. (250 MPa). All other miscellaneous secondary members shall have minimum yield strength of 36,000 P.S.I. (250 Mpa). All field connections shall be bolted and primary bolted connections shall be furnished with high strength bolts conforming to the physical specifications of ASTM A325 or equivalent.Secondary bolted connections shall be furnished with machine bolts conforming to the physical specifications of ASTM A307 (or equivalent).All structural members shall be cleaned by wire brushing to remove dirt, grease, oil and loose mill scale and given one shop coat of red oxide, air drying, phenol modified alkyd resin primer and painted with two coats of synthetic enamel paint to achieve an even shade.The item shall be inclusive of necessary accessories, submission of shop drawings for approval etc., all complete as directed by Engineer-in-charge.

Supply, fabricating and erecting secondary members like purlins, girts, eave struts, wind bracing, flange bracing, base angles, clips etc., made of C and Z sections with available thickness of 1.6mm / 1.8mm / 2.0mm / 2.5mm, fabricated by cold forming process and shall conform to the physical specifications of ASTM A570 (Grade 50) or equivalent and having a minimum yield strength of 50,000 P.S.I (345 MPa) and galvanised with zinc coating of not less than Z275 (275 g/m2 minimum coating mass), conforming to IS 277 / IS 15961 .The secondary members shall be fixed with bolts and nuts having integral washers and shall be tightened to 55 Nm torque. Purlin bolts of standard grade 4.6 or high strength grade 8.8 as per design requirement shall be used . The item shall be inclusive of necessary accessories, submission of shop drawings for approval etc., all complete as directed by Engineer-in-charge.

Structural steel work of factory made MS holding down foundation bolts including nuts and washer plates of any diameter including necessary threading and machining and installing in concrete foundation including levelling & aligning etc complete.

Supply and fixing of Bare Zincalume roof sheeting of approved make, of Kliplok system, concealed fix onsite roll formed profile shall be made of 0.50mm BMT (0.55mm TCT)), 700mm effective cover width with four major deep corrugation, 43mm deep rib spaced at 233mm c/c with micro stiffeners perpendicular to ribs for strength. The male and female rib shall have anti-capillary groove of Kliplok . The steel sheet shall be of high tensile strength G550 (min yield strength Fy=550Mpa), metallic coated with Zinc-Aluminium alloy (i.e. 55% Al, 43.4% Zinc, 1.6% Si - Zincalume), AZ150 (min 150 gm/m2 total on both side), conforming to AS1397/ IS15961 class 3 for the durability . The steel sheet shall have brand marking of coated steel manufacturer on back side at regular interval confirming genuinity of the material. The sheet shall be fixed to every purlin by means of galvanised high strength steel clips having spurs which will securely hold the sheets in position and lock-in the sidelap and both centre ribs. The concealed clip shall be fastened with 40μm zinc coated or 25μm zinc-tin alloy coated, Hex head, self-drilling screw as per AS 3566-2002 Class 3 fasteners of approved make of Buildex/Roofix or equivalent with EPDM washer of approved make conforming to AS1365 class 3. The measurement shall be based on finished/covered surface area.

Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete :

Ridges plain (500 - 600mm)

Gutter (600mm overall girth)

Providing, fitting and fixing plain permanently colour coated sheets, for flashing / trimming / closure for vertical / horizontal joints, capping etc. steel with aluminium-zinc alloy coated i.e. Zincalume steel AZ150 with minimum bare metal thickness (i.e. excluding the thickness of coating and painting) of 0.45mm of grade G550 as per AS1397 , painted with Super Durable Polyester paint system with solar reflectance technology in approved color, suitable for exterior application conforming to AS/NZS 2728 type-4 / IS15965 class 3 . The sheet shall have a total paint coating thickness of 35 microns. The top coat is coated with super durable polyester paint system of nominal 20 microns on exposed surface and 5 micron reverse polyester coat on back surface over 5 micron primer coat on both surfaces. The trims /flashings shall be attached to girts / purlins with screws conforming to Australian standard AS3566 class 3- 4. Screws shall be mechanically coated with min. 25 micron Zn-Sn alloy or hot dipped zinc coated with min. 40 micron hexagonal self-drilling fasteners with EPDM washer of approved make conforming to AS1365 class 3.

Supplying & fixing Sky Lights made of poly carbonate sheet of TUFLITE or equivalent make including all necessary accessories for fixing . The sheet shall be made of solid polycarbonate , having embossments on bottom side, matching with roofing profile shape of 1.5mm thickness with UV protective film on top side with 90% light transmission. The sheet shall be fixed with 32mm dia Weatherlok washer/ dome washer with 10mm extra length and screws shall comply to AS3566 class 3-4 .The item shall include cost of predrilling with bigger hole if standard screws are used .The fixing shall be done as per manufacturer recommendation. The profile and properties shall be approved by Engineer-in-charge prior to installation.

SUB HEAD XI :MISCELLANEOUS

Providing and supplying aluminium extruded tubular and other aluminium sections as per the architectural drawings and approved shop drawings , the aluminium quality as per grade 6063 T5 or T6 as per BS 1474,including super durable powder coating of 60-80 microns conforming to AAMA 2604 of required colour and shade as approved by the Engineer-in-Charge. ( The item includes cost of material such as cleats, sleeves, screws etc. necessary for fabrication of extruded aluminium frame work. Nothing extra shall be paid on this account). The weight of aluminium extruded section shall be taken for purpose of payment.

Designing, fabricating, testing, protection, installing and fixing in position semi (grid) unitized system of structural glazing (with open joints) for linear as well as curvilinear portions of the building for all heights and all levels, including:

Structural analysis & design and preparation of shop drawings for the specified design loads conforming to IS 875 part III (the system must passed the proof test at 1.5 times design wind pressure without any failure), including functional design of the aluminum sections for fixing glazing panels of various thicknesses, aluminium cleats, sleeves and splice plates etc. gaskets, screws, toggles, nuts, bolts, clamps etc., structural and weather silicone sealants, flashings, fire stop (barrier)- cum-smoke seals, microwave cured EPDM gaskets for water tightness, pressure equalisation & drainage and protection against fire hazard including:

Fabricating and supplying serrated M.S. hot dip galvanised / Aluminium alloy of 6005 T5 brackets of required sizes, sections and profiles etc. to accommodate 3 Dimentional movement for achieving perfect verticality and fixing structural glazing system rigidly to the RCC/ masonry/structural steel framework of building structure using stainless steel anchor fasteners/ bolts, nylon seperator to prevent bimetallic contacts with nuts and washers etc. of stainless steel grade 316, of the required capacity and in required numbers.

Providing and filling, two part pump filled, structural silicone sealant and one part weather silicone sealant compatible with the structural silicone sealant of required bite size in a clean and controlled factory / work shop environment, including double sided spacer tape, setting blocks and backer rod, all of approved grade, brand and manufacture, as per the approved sealant design, within and all around the perimeter for holding glass.

Providing and fixing in position flashings of solid aluminium sheet 1 mm thick and of sizes, shapes and profiles, as required as per the site conditions, to seal the gap between the building structure and all its interfaces with curtain glazing to make it watertight.

Making provision for drainage of moisture/ water that enters the curtain glazing system to make it watertight, by incorporating principles of pressure equalization, providing suitable gutter profiles at bottom (if required), making necessary holes of required sizes and of required numbers etc. complete. This item includes cost of all inputs of designing, labour for fabricating and installation of aluminium grid, installation of glazed units, T&P, scaffolding and other incidental charges including wastages etc., enabling temporary structures and services, cranes or cradles etc. as described above and as specified. The item includes the cost of getting all the structural and functional design including shop drawings checked by a structural designer, dully approved by Engineer-in-charge. The item also includes the cost of all mock ups at site, cost of all samples of the individual components for testing in an approved laboratory, field tests on the assembled working structural glazing as specified, cleaning and protection till the handing over of the building for occupation. In the end, the Contractor shall provide a water tight structural glazing having all the performance characteristics etc. all complete as required, as per the Architectural drawings, as per item description, as specified, as per the approved shop drawings and as directed by the Engineer -In- Charge.

Note:- 1. The cost of providing extruded aluminium frames, shadow boxes, extruded aluminium section capping for fixing in the grooves of the curtain glazing and vermin proof stainless steel wire mesh shall be paid for separately under relevant items under this sub- head. However, for the purpose of payment, only the actual area of structural glazing (including width of grooves) on the external face shall be measured in sqm. up to two decimal places.

Note:-2. The following performance test are to be conducted on structural glazing system if area of structural glazing exceeds 2500 Sqm from the certified laboratories accreditated by NABL(National Accreditation Board for Testing and Calibration Laboratories), Department of Science & Technologies, India. Cost of testing is payable separately.

The NIT approving authority will decide the necessity of testing on the basis of cost of the work, cost of the test and importance of the work. Performance Testing of Structural glazing system Tests to be conducted in the NABL accredited lab or any other accreditation body which operates in accordance with ISO/ IEC 17011 and accredits labs as per ISO/IEC 17025

1. Performance Laboratory Test for Air Leakage Test (-50pa to - 300pa) & (+50pa to +300pa) as per ASTM E-283-04 testing method for a range of testing limit 1 to 200 mVhr

2. Static Water Penetration Test. (50pa to 1500pa) as per ASTME- 331-09 testing method for a range up to 2000 ml.

3. Dynamic Water Penetration (50pa to 1500pa) as per AAMA 501.01- 05 testing method for a range upto 2000 ml

4. Structural Performance Deflection and deformation by static air pressure test (1.5 times design wind pressure without any failure) as per ASTME-330-10 testing method for a range upto 50 mm

5. Seismic Movement Test (upto 30 mm) as per AAMA 501.4-09 testing method for Qualitative test, Tests to be conducted on site.

6. Onsite Test for Water Leakage for a pressure range 50 kpa to 240 kpa (35psi) upto 2000 ml

Providing, assembling and supplying vision glass panels (IGUs) comprising of hermetically-sealed 6-12- 6 mm insulated glass (double glazed) vision panel units of size and shape as required and specified, comprising of an outer heat strengthened float glass 6mm thick, of approved colour and shade with reflective soft coating on surface # 2 of approved colour and shade, an inner Heat strengthned clear float glass 6mm thick, spacer tube 12mm wide, dessicants, including primary seal and secondary seal (structural silicone sealant) etc. all complete for the required performances, as per the Architectural drawings, as per the approved shop drawings, as specified and as directed by the Engineer-in-Charge. The IGUs shall be assembled in the factory/ workshop of the glass processor.

(Payment for fixing of IGU Panels in the curtain glazing is included in the cost of above item )

For payment, only the actual area of glass on face # 1 of the glass panels (excluding the areas of the grooves and weather silicone sealant) provided and fixed in position, shall be measured in sqm.

(i) Coloured tinted float glass 6mm thick substrate with reflective soft coating on face # 2, + 12mm Airgap + 6mm Heat Strengthened clear Glass of approved make having properties as visible Light transmittance (VLT) of 25 to 35 %, Light reflection internal 10 to 15%, light reflection external 10 to 20 %, shading coefficient (0.25- 0.28) and U value of 3.0 to 3.3 W/ m2 degree K etc. The properties of performance glass shall be decided by technical sanctioning authority as per the site requirement.

Extra for openable side / top hung vision glass panels (IGUs) including providing and supplying at site all accessories and hardwares for the openable panels as specified and of the approved make such as heavy duty stainless steel friction hinges, min 4 -point cremone locking sets with stainless steel plates, handles, buffers etc. including necessary stainless steel screws/ fasteners, nuts, bolts, washers etc. all complete as per the architectural drawings, as per the approved shop drawings, as specified and as directed by the Engineer- in- Charge.

SUB HEAD XII :SANITARY SERVICES:

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required.

W.C. pan with ISI marked white solid plastic seat and lid

Providing & fixing White vitreous china water closet squatting pan (Indian type & European type) along with "S" or "P" trap with all operations including all necessary materials all complete as per the direction of Engineer-in charge.

Long pattern W.C Pan of size 580x440 mm

Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required:

White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests

Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350mm or 340x410x265mm sizes respectively with C.P. brass spreaders with union, CP brass 32mm bottle trap of approved quality and make, cutting and making good the walls and floors wherever required etc, complete.

Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms.

Providing,fitting and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931. 15 mm nominal bore

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require:

White Vitreous China flat back wash basin size 550x400 mm with a single 15 mm C.P. brass pillar tap.

Providing and fixing Table top Wash Hand Basin comprising of; a) Glazed vitreous china Table top wash basin of approved brand/ make, shape, size and pattern b) One pillar cock of approved make c) One 15mm heavy quality flexible PVC inlet pipe connection with C.P.brass hexagonal check nuts with washers at both ends. d) One 15mm Angle Stop Cock on the inlet to the basin e) One 32mm heavy quality CP brass waste coupling with rubber plug and CP chain f) Bottle Trap with internal parttion, 32mm size with 300mm and 190mm long wall connection pipes and wall flange. g) 32mm PVC waste pipe with specials from extension piece of the bottle trap to the floor trap, length not exceeding 1mtr.concealed in the wall.

Providing and fixing CP brass 32mm size bottle trap of approved quality and make and as per the directions of Engineer-in-charge.

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Rectangular

Providing and fixing toilet paper holder : C.P. brass

Providing and fixing CP brass towel rail of approved quality and make with necessary screws etc, complete.

Providing & fixing sqare mouth S W Gully trap grade A complete with CI grating brick machinery chamber with water tight C I cover with frame of 300x300 mm (Size inside ) The weight of cover to be not less than 4.5 kg & frame to be not less than 2.70 kg as per standard design.

100x100 mm size P type.

Supplying, laying, jointing, testing and commissioning; UPVC(SWR) pipe (Type-B) as per IS : 13592/1992 including specials of best quality and approved make fixed to wall/floor including chasing, cutting, making the hole in walls/floors, cutting the pipes to the required size of length jointing the pipes and specials with suitable resin and testing etc.,complete all as specified and directed. (Specials at junctions must have access doors wherever required.)

75 mm dia

110 mm dia

Providing and fixing PVC 75mm size Nahani Trap of approved make (Supreme) conforming to ISI Specifications and construction of Cistern in CC 1:2:4 as per directions (Rate is inclusive of cost of materials and fixtures and conveyance of materials to work spot)

Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet :

100 mm diameter including shower arm

Providing and fixing C.P. brass angle valve of approved quality conforming to IS:8931.

15 mm nominal bore

Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge

Providing and fixing CP brass wall mixer with provision for overhead shower with 115mm long bend pipe on upper side, connecting legs and wall flanges of approved quality and make.

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required :

Kitchen sink with drain board of size 510x1040 mm bowl depth 250mm.

Providing and fixing PVC waste pipe for sink or wash basin including PVC waste fittings complete.

Semi rigid pipe 40mm dia

Providing and fixing unplasticised PVC connection pipe with brass unions.

30cm length 15mm nominal bore

Providing and fixing CP brass bib cock of approved quality conforming to IS:8931

15mm nominal bore

Providing and fixing CP brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690gms.

15mm nominal bore

Providing and fixing CP brass two way bib cock of approved quality and make

Providing and fixing CP brass sink cock with swinging casted spout of wall mounted model of approved quality and make.

Providing fixing in position storage type hot water electical geyser (5 star rating) (vertical or horizontal) including making connection in all respects.

15 Litres capacity

Constructing brick masonry chamber for underground C.I. inspection chamber and bends with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover with frame to be not less than 38 Kg (weight of cover 23 Kg and weight of frame 15 Kg), R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 fine sand : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand), finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design:

Inside dimensions 455x610 mm and 45 cm deep for single pipe line :

With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

SUB HEAD-XIII :INTERNAL WATER SUPPLY SERVICES

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & Brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc.

15mm nominal outer dia pipes

20mm nominal outer dia pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.

Internal work - Exposed on wall

25 mm dia nominal bore

32 mm dia nominal bore

40 mm dia nominal bore

Supplying and fixing in position best quality and approved make heavy quality screws down gun metal gate valves with hand wheel of the following sizes fixed to service lines including testing, making good the leakages, if any etc.,

Providing & Fixing HDPE Over Head water storage tanks of the approved quality, & of the following capacity including making solid supported base as per instructions & doing all connections as required to make the work complete in all respects.

1000 lit. capacity

500lit. capacity

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. External work.

25mm nominal outer dia pipes

32mm nominal outer dia pipes

40mm nominal outer dia pipes

SUBHEAD-XIV INTERNAL ELECTRIFICATION

Wiring for light point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed heavy guage FRLS PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm.FRLS PVC insulated copper conductor single core cable etc as required.

Group-A

Point Wiring for Light/ Fan/ exhaust fan with 2 runs of 1100V grade 1.5 Sq.mm & 1 run of 1.5 Sq.mm FRLS insulated multistranded Copper wires, run in & including 25mm dia, guage FRLS PVC ISI mark conduits concealed in wall after necessary chase cutting with finishing/surface in wall / ceiling conforming to IS 732 including all accessories such as junction boxes, conduit bends, elbows and ceiling rose, anodised GI Switch box with modular switch and the box covered with front plate.

Two Lights point controlled by one 6A switch.

Three Lights point controlled by one 6A switch.

Four Lights point controlled by one 6A switch.

Wiring for High Bay Fitting with 3Cx2.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed steel conduit, with 10/16A MCB etc. as required.

Group C

Wiring for High Bay Fitting (Looped) with 3Cx2.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed steel conduit, with 10/16A MCB etc. as required.

Group C

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 amps modular socket outlet and 5/6 amps modular switch, connection etc. as required.

Supply and wiring similar to item 1 above but for Ceiling Fan point including GI box and controled by one 6A switch, 100W Step type Electronic regulator with Concealed MS fan hook box.

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed heavy guage FRLS PVC conduit as required

2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire

2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

4 X 2.5 sq. mm + 2 X 2.5 sq. mm earth wire

4 X 6 sq. mm + 2 X 6 sq. mm earth wire

2 X 6 sq. mm + 1 X 6 sq. mm earth wire

3C x 16 SQ.MM CU.Flx. CABLE

Light/Fan Fixtures

Supply, Installation, Testing & Commissioning of the following Light Fixture with lamp, Control Gear & All necessary accessories. Luminaries with all electrical accessories & it should be energy efficient, etc are prewired up to the terminal block & mounted on a removable control gear module for ease of maintenance. All electrical connections of the control gear module with the rest of the luminaries should be click fix & require use of no tools. Mounting options should be for both lateral as well as pole top mounting with Lamp Control Gear & Fixing Accessories. All fixtures shall be white colour & supplied with white lamps. All the light fixtures will be finally approved by Architect / Consultant/ Department. Architect / Consultant / Department reserves the right to reject the fittings suggested by the contractor.

20W,2000 lumens T8,1200mm length LED retrofit tube light with aluminium anodised body, input voltage AC 220 - 260 Volts with PF>0.9, Surge protection: 2KV,THD<10%, with inbuilt driver and frosted cover CCT: 3000K - 5700K, minimum CRI>70, .etc., complete as per IS 10322

IP65 20W,2000 lumens T8,1200mm length LED retrofit tube light with aluminium anodised body, input voltage AC 220 - 260 Volts with PF>0.9, Surge protection: 2KV,THD<10%, with inbuilt driver and frosted cover CCT: 3000K - 5700K, minimum CRI>70, .etc., complete as per IS 10322

30/36 Watt Recessed LED 2 x 2 panel with minimum luminaire system efficacy of 100 lm/w having a color temperature of 5700K and housing should made up of powder coated CRCA with high efficiency diffuser with driver, accessories wiring etc.

12 Watt surface mounted LED Downlighter with minimum luminaire system efficacy of 100 lm/w having a color temperature of 5700K and housing should made up of pressure die cast aluminium with high efficiency diffuser with driver, accessories wiring etc.

11 Watt Decorative Mirror Light LED light fixture with minimum luminaire system efficacy of 70 lm/w having a color temperature of 5700K and housing should made up of pressure die cast aluminium with high efficiency diffuser with driver, accessories wiring etc

18 Watt Recessed LED Downlighter with minimum luminaire system efficacy of 100 lm/w having a color temperature of 5700K and housing should made up of pressure die cast aluminium with high efficiency diffuser with driver, accessories wiring etc.

18 Watt surface mounted LED Downlighter with minimum luminaire system efficacy of 100 lm/w having a color temperature of 5700K and housing should made up of pressure die cast aluminium with high efficiency diffuser with driver, accessories wiring etc.

Ceiling Fans

Supply, Installation, Testing and Commissioning of 1200 mm sweep,BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC)Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CM/M/W) minimum 6.00, Air delivery minimum 210 Cum/Min , 350 RPM (tolerance as per IS : 374-2019), THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required..

1200mm Sweep 5 Star rated Ceiling fans

Supply, Installation on RCC/steel column using suitable mounting arrangements, testing & commissioning of 30"(750mm) dia, 1400 rpm heavy duty oscillating type industrial Wall Mounted Air Circulators along with three speed regulator suitable to single phase 230v gr, of any approved make with all connected accessories and interconnections, including power cord with 5A,3 pin plug top complete in all respects and as directed by Engineer-In-Charge. Note : 3 speed regulator shall be mounted at reacheable height as directed by Engineer-In-Charge

Supply, installation, Testing and Commissioning of Double ball bearing 60W Wall mounted airculator Fan (450 mm) with poweder coated mesh guards as per safety standards ,service value,Complete Fan Head, wall Bracket, Mounting accessories kit, with 2 years Guarantee all accessories etc.,

Supply, Installation & Testing of following PVC Body with Louvers exhaust fan suitable for single phase, 240V, AC supply complete with motor all accessories etc complete.

250mm Sweep

Supply Installation Testing and commissioning of TPN MCB Double door Distribution boards dust and vermin protected and rated for 415V Three Phase AC supply operation including incoming MCB /ELCB as per specifications and required capacity Neutral bar and Earth terminal complete as required and installed in concealed in wall after necessary chase cutting with finishing/surface in wall including all fixing materials required. MCBs shall conform to IS : 8828 and ELCB shall conform to IS :12640. All MCBs shall be 'C' Curve. DBs shall be provided along with required wire adopter boxes around the DB as required and dummys for spare ways in the DB (No claim shall be allowed for the same).

4Way TPNMCBDB with 40A, 100mA 4Pole RCBO as incomer and 9 nos 6-25A SPMCBs and 3nos 8KA SP SPDs as outgoings. (LDBs)

8Way SPN MCB DB with 32A, DP as incomer and 6 nos 6-25A SP MCBs as outgoings. (LDBs)

6Way TPNMCBDB with 40A, 100mA 4Pole RCBO as incomer and 15 nos 6-25A SPMCBs and 3nos 8KA SP SPDs as outgoings. (LDBs)

8Way TPNMCBDB with 40A, 100mA 4Pole RCBO as incomer and 21 nos 6-25A SPMCBs and 3nos 8KA SP SPDs as outgoings. (LDBs)

Supply & installation of Stand alone 360 degrees dual relay(2Channels) Occupancy sensor with 10A potential free contact including all fixing accessories 230V AC Supply and interconnections complete as required.

Supplying and fixing of 25mm medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required

SUBHEAD-XV POWER WIRING

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 amps modular socket outlet and 15/16 amps modular switch, connection etc. as required.

Supplying and fixing 20 amps, 240 volts, SPN industrial type, socket outlet, with 2 pole and earth, metal enclosed plug top alongwith 20 amps “C” curve, SP, MCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required.

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed heavy guage FRLS PVC conduit as required

2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

2 X 4 sq. mm + 1 X 4 sq. mm earth wire

4 X 4 sq. mm + 2 X 4 sq. mm earth wire

2 X 6 sq. mm + 1 X 6 sq. mm earth wire

4 X 10 sq. mm + 2 X 6 sq. mm earth wire

Supply Installation Testing and commissioning of TPN MCB Double door Distribution boards dust and vermin protected and rated for 415V Three Phase AC supply operation including incoming MCB /ELCB as per specifications and required capacity Neutral bar and Earth terminal complete as required and installed in concealed in wall after necessary chase cutting with finishing/surface in wall including all fixing materials required. MCBs shall conform to IS : 8828 and ELCB shall conform to IS :12640. All MCBs shall be 'C' Curve. DBs shall be provided along with required wire adopter boxes around the DB as required and dummies for spare ways in the DB (No claim shall be allowed for the same).

6Way TPNMCBDB with 63A, 100mA 4Pole RCBO as incomer and 15nos 6-25A SPMCBs and 3nos 8KA SP SPDs as outgoings.

4Way TPNMCBDB with 63A, 100mA 4Pole RCBO as incomer and 9nos 6-25A SPMCBs and 3nos 8KA SP SPDs as outgoings.

Supply and laying of 80mm dia Class 'B' GI pipes laid 750mm below ground level including excavation, back filling etc., complete.

SUBHEAD XVI : UPS WIRING

Supply and fixing of modular type single phase 3nos 6A 5pin shuttered type Socket with 1no 16A switch with front plate and anodised GI box including all fixing accessories.

Supply and fixing of modular type single phase 1no 16A 6pin shuttered type Socket with 1nos 16A switch with front plate and anodised GI box including all fixing accessories.

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FR PVC insulated copper conductor, single core cable in surface/ recessed heavy guage FRLS conduit as required

2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

2 X 4 sq. mm + 1 X 4 sq. mm earth wire

4 X 6 sq. mm + 2 X 6 sq. mm earth wire

4 X 10 sq. mm + 2 X 6 sq. mm earth wire

Supply Installation Testing and commissioning of TPN MCB Double door Distribution boards dust, water proof and vermin protected and rated for 415V Three Phase AC supply operation including incoming MCB /RCBO as per specifications and required capacity Neutral bar and Earth terminal complete as required and installed in flush with wall including all fixing materials required. MCBs shall conform to IS : 8828 and ELCB /RCBO shall conform to IS : 12640. All MCBs shall be D Curve.

6Way TPNMCBDB with 63A 4Pole MCB & 4P 32KA SPDs as incomer and 18nos 6-25A SPMCBs as outgoings.

6Way SPN MCB DB with 32A, DP as incomer and 6 nos 6-25A SP MCBs as outgoings. (LDBs)

SUBHEAD XVI : SHOP ELECTRICALS

Supply and fixing of Three phase 32A 3P+N+E wall mounted switched interlocking sockets and surface mounting with 3P+N+E plug including all fixing accessories.

Supply and fixing of Three phase 63A 3P+N+E wall mounted switched interlocking sockets and surface mounting with 3P+N+E plug including all fixing accessories.

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed heavy guage FRLS PVC conduit as required

4 X 6 sq. mm + 2 X 6 sq. mm earth wire

4 X 10 sq. mm + 2 X 6 sq. mm earth wire

4 X 16 sq. mm + 2 X 6 sq. mm earth wire

Supply, fabricating, installing the following size perforated GI cable Trays including horizontal and vertical bends, reducers, tees, cross members,suspenders and other accessories as required and duly suspended from the ceiling/fixing to the wall/RCC beam/iron structures using M.S. angle supports and including necessary fixing hardware as required and as per site requirements.

150mm x 54mm, The Load bearing capacity of the Cable Trays should be minimum of 29.51KG/meter at the span of 1.5Meter.

300mm x 54mm, The Load bearing capacity of the Cable Trays should be minimum of 57.66KG/meter at the span of 1.5Meter

500mm x 54mm, The Load bearing capacity of the Cable Trays should be minimum of 107.78KG/meter at the span of 1.5Meter

SUBHEAD XVIII : TELEPHONE WIRING & LAN CONDUITING

Supplying and fixing of following sizes of heavy class FRLS PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required.

Supply and laying of 25mm dia. 2mm thick PVC conduit concealed in wall/ ceiling/floor and drawing of 12SWG GI wire as fish wire for laying of LAN Cables at a later stage and supply of all fixing accessories such as junction boxes, conduit bends, etc., complete as required.

Supply and fixing of Telephone outlet (RJ11) with anodised GI box of with front plate and telephone socket

Supply and fixing of telephone outlet (RJ45) with anodised GI box of with front plate

Supply and fixing of LAN outlet (RJ45) with anodised GI box of with front plate

Supplying and drawing following pair 0.5 sq mm FR PVC insulated annealed copper conductor, unarmored telephone cable in the existing surface/ recessed steel/ PVC conduit as required.

Supply and installation of following size Krone connectors in MS box complete as required.

SUB HEAD-XIX : FURNITURE

Proving and fixing of Wooden display cabinet ion Designer pattern made out of 19 mm thick commercial board with 1 mm thick laminate with 5 mm thick glass Shutters all edges covered with teak wood leaping and finish with melamine polish etc all complete.

Supply & fixing of writing board of size 1200 x 1800 mm made out of aluminium frame, with 09 mm plywood with 1 mm thick lamination etc complete.

Providing and fixing of Conference Table for 15 persons ,600 mm wide and 750 mm height made out of 18 mm thick plywood for frame work, shelf, foot rest and front facia, provision to accommodate conduits for wiring, front, top and side end surfaces to have 3.5 mm thick approved shade veneer paneling, exposed edges of ply wood covered with teak wood beading, exposed veneer of top shall be finished with melamine polish finish of approved shade, ends and fronts veneered surfaces finished with melamine polish, internal exposed surfaces of the table finished with two coats of enamel paint over one coat of wood primer including surface preparation etc., all complete as directed by Engineer -in-charge.

Supply and placement of Conference Medium back revolving chair made up of 1.2cm thick hot-pressed plywood for seat and back, upholstered with fabric upholstery covers and moulded polyurethane foam. The polyurethane foam is moulded with density = 45 +2 kg/m and hardness = 20 ±2, on hampden machine at 25% compression. The one-piece armrests are injection moulded from black Co-polymer polypropylene. The bellow is 3 piece telescopic type and injection moulded in black polypropylene. The pedestal is injection moulded in balck 30% glass-filled Nylon and fitted with 5 Nos. of Twin wheel castors. The twin wheel castors are injection moulded in 30% glass filled black Nylon etc., complete all as Mid Back of Godrej Make or eqivalents of Wipro/Featherlite/Durian /Ergo.

Supply and placement of Conference High back chair, cushioned seat assembly shall consists of insert moulded polyurethane foam upholstered with foam laminated mesh fabric, the insert moulded foam is assembeied over a load bearing plastic seat cover. The back shall made up of two piece injection moulded frame. The inner frame shall be upholstered with mesh fabric and mounted on the main assembly..armrest shall be injection moulded with height adjustable up to 4.5+/- 0.5cm in 3 steps and width adjustable up to 20mm. The mechanism of chair shall have following features:360 degree revolving type, Front pivot Synchro mechanism, Tilt tension adjustment, 3 position tilt limiter with Anti-Shock feature. Spine bracket shall made of Aluminium diecast piece connecting back with mechanism. Neck rest assembly shall made up of polyurethane foam upholstered with foam laminated mesh fabric. The neck rest assembly is mounted on the top of back, it can be adjusted up to 4.5+/-0.5cm up- down and has regular adjustment of 30 degree +1-2. The chair shall be provided with pneumatic height adjustment which shall have stroke of 9.0 +/- 0.3 cm. of or equivalent of Godrej, Wipro, Featherlite, Durian, HoF, Ergo.

\Supply and placement of Centre Table of size 1050x525x450 mm made out of teak wood frame work of 70 x 25mm and legs with 45 x 45mm with 8mm thick glass top and 18 mm thick plywood with 1 mm thick laminate on bottom with spirit polish etc.all complete as directed by Engineer -in-charge.

Supply of Computer Table of size 1200 x 600 x 750mm made out of 18mm plywood with 1mm thick laminate with drawer units having necessary locking arrangements, all exposed edges to have 6mm thick TW beading, Necessary hardware fittings including accessories like CPU trolley, keyboard slide out tray with mouse pad etc; complete with sprit polish.

Supply of Computer chairs made up of 1.2cm thick hot-pressed plywood for seat and back, upholstered with fabric upholstery covers and moulded polyurethane foam. BACK SIZE : 47.5 cm. (W) with SEAT SIZE : 47.0 cm. (W) x 48.0 cm. (D) The polyurethane foam is moulded with density = 45 ±2 kg/m and hardness = 20 ±2, on hampden machine at 25% compression. The one-piece armrests are injection moulded from black Co-polymer polypropylene.The chair shall have center tilt mechanism. The bellow is 3 piece telescopic type and injection moulded in black polypropylene. The pedestal is injection moulded in balck 30% glass-filled Nylon and fitted with 5 Nos. of Twin wheel castors. The twin wheel castors are injection moulded in 30% glass filled black Nylon etc., complete all as per Godrej Make or eqivalents of Wipro/Featherlite/Durian/Ergo/Ikea.

Supply of side unit of size 1050 x 450 x 750 mm approved shade with one drawer on sliding guide channels and one openable shutter with shelves, made out of 18 / 12 mm thick commercial plywood with 1mm thick lamination of approved brand and shade for frame / box work, drawers, shelves and shutters and top, exposed internal surfaces finished with 0.60mm thick lamination of approved brand and shade, superior quality brushed steel hardware fittings, locking arrangements, teak wood beading / lamination to all exposed edges,un exposed internal surfaces shall be finished with 2 coats of enamel paint and wood primer including surface preparation etc, complete all as directed.

Supply of officer Table of size 1800 x 900 x 750 mm made out of 18mm thick commercial plywood with 1mm thick lamination of approved brand and shade for frame / box work and top, exposed internal surfaces finished with 0.60mm thick lamination of approved brand and shade, drawer unit with three drawers on sliding channels, key board slide out tray of approved brand, superior quality brushed steel hardware fittings, locking arrangements, teak wood beading / lamination to all exposed edges,un exposed internal surfaces shall be finished with 2 coats of enamel paint and wood primer including surface preparation etc, complete all as directed.

Supply and placement of Officers High back chair, cushioned seat assembly shall consists of insert moulded polyurethane foam upholstered with foam laminated mesh fabric, the insert moulded foam is assembeied over a load bearing plastic seat cover. The back shall made up of two piece injection moulded frame. The inner frame shall be upholstered with mesh fabric and mounted on the main assembly..armrest shall be injection moulded with height adjustable up to 4.5+/- 0.5cm in 3 steps and width adjustable up to 20mm. The mechanism of chair shall have following features:360 degree revolving type, Front pivot Synchro mechanism, Tilt tension adjustment, 3 position tilt limiter with Anti-Shock feature. Spine bracket shall made of Aluminium diecast piece connecting back with mechanism. Neck rest assembly shall made up of polyurethane foam upholstered with foam laminated mesh fabric.The neck rest assembly is mounted on the top of back, it can be adjusted up to 4.5+/-0.5cm up- down and has regular adjustment of 30 degree +1-2. The chair shall be provided with pneumatic height adjustment which shall have stroke of 9.0 +/- 0.3 cm. of or equivalent of Godrej, Wipro, Featherlite, Durian, HoF, Ergo.

Supply of Visitor chair with arms, without castors, cushion at seat and back duly upholsted. The polyurethane foam is moulded density 45±2 kg/m³ and hardsness 20±2 at 25% compression with PU arm rest injection moulded from black co polymer polypropylene. The powder coated tublar frame is cantiliver type and made out of 25.4mm x 2mm thick MS ERW tube etc., complete all as per Godrej Make or eqivalents of Wipro/Featherlite/Durian/ERGO.

Supply of Executive Table of size 2100 x 1000 x 750 mm made out of 18mm plywood with 3.5mm thick veneer of approved shade for frame / box work and top, exposed internal surfaces finished with 0.60mm thick lamination of approved brand and shade, four drawers on one side, front panel of 18mm thick plywood with 12mm thick niche with vertical / horizontal veneer grains, all exposed edges to have teakwood beading, top to have moulded teak wood beading, superior quality brushed steel hardware fittings, locking arrangements, P.U polish finish to top and melamine polish finish to all exposed veneer surface with etc., complete all as directed.

Supply of side unit of size 1200 x 450 x 625mm made out of 18/12mm commercial plywood with 3.5mm thick veneer of approved shade for frame / box work, shelves, shutters,drawers and top, exposed internal surfaces finished with 0.60mm thick lamination of approved brand and shade, drawers with sliding channels, all exposed edges to have teakwood beading, top to have moulded teak wood beading, superior quality brushed steel hardware fittings, locking arrangements, P.U polish finish to top and melamine polish finish to all exposed veneer surfaces, un exposed internal surfaces shall be finished with 2 coats of enamel paint and wood primer including surface preparation etc., complete all as directed.

Supply and placement of Slime Line 4S shall have an overall size of 916mm(W)x486mm(D)x1980mm(H) with welded / Ripet System construction. It should have the shelf thickness of 0.7 mm, Back thickness of 0.8mm, Door thickness of 0.8mm (high yield strength) and all other components shall have a thickness of 0.9mm. These components shall be made of CRCA 'D' grade high yield strength as per IS:513. The Storwel Plain should have a Mazak handle and Three way locking mechanism with Shooting Bolts. It should have a height wise adjustable shelf mounting which shall have a Uniformly Distributed Load Capacity of max 40 Kg. It should also have a M10 Screw type Leveller with Hex plastic base. The finishing shall include Epoxy powder coated to the thickness of 50 microns (+/- 10) of Godrej model Slime Line 4S or equivalent of Wipro, Featherlite, Durian , Ergo, HoF,

Supply and placement of three seater sofa of size 1950x700x740mm made out of second class hard wood frame work, arm rests shall have 100mm wide x 18mm thick teak wood, flat springs for seat and nawar strips for back, cladded with 100mm thick 40 density foam for seat and 70mm thick 32 density foam for back, 10mm thick medium density poly foam for countering with white cloth lining, upholstered with fabric of approved brand and shade (cost of fabric not to be exceed Rs 250/- meter) , exposed wooden surface finished with melamine polish etc, complete all as per drawings and as directed.

Supply and placement of two seater sofa of size 1500x700x740mm made out of second class hard wood frame work, arm rests shall have 100mm wide x 18mm thick teak wood, flat springs for seat and nawar strips for back, cladded with 100mm thick 40 density foam for seat and 70mm thick 32 density foam for back, 10mm thick medium density poly foam for countering with white cloth lining, upholstered with fabric of approved brand and shade (cost of fabric not to be exceed Rs 250/- meter) , exposed wooden surface finished with melamine polish etc, complete all as per drawings and as directed.

Supply and placement of single seater sofa of size 700x700x740mm made out of second class hard wood frame work, arm rests shall have 100mm wide x18mm thick teak wood, flat springs for seat and nawar strips for back, cladded with 100mm thick 40 density foam for seat and 70mm thick 32 density foam for back, 10mm thick medium density poly foam for countering with white cloth lining, upholstered with fabric of approved brand and shade (cost of fabric not to be exceed Rs 250/- meter), exposed wooden surface finished with melamine polish etc, complete all as per drawing and as directed.

Supply and placement of Peg. Table of size 525 x 525 x 450mm made out of teak wood frame siderail 70x25mm & legs 45x45mm) top with 18mm thick commercial board and 8mm thick Glass, all exposed edges to have teak wood beading finished with melamine polish etc., all complete as per drawings.

Supply of officer Table of size 1500 x 750 x 750 mm made out of 18mm thick commercial plywood with 1mm thick lamination of approved brand and shade for frame / box work and top, exposed internal surfaces finished with 0.60mm thick lamination of approved brand and shade, drawer unit with three drawers on sliding channels, key board slide out tray of approved brand, superior quality brushed steel hardware fittings, locking arrangements, teak wood beading / lamination to all exposed edges,un exposed internal surfaces shall be finished with 2 coats of enamel paint and wood primer including surface preparation etc, complete all as directed.

Supply of Steel Storage rack of size 2000 x 900 x 450 mm made out of MS "C" Angle of 2mm thick with five panels of M.S. sheet of 14 guage with spray enamel paint complete all as per make of Godrej or equivalent / featherlite/ Wipro/ERGO Etc; complete. .

Supply of Revolviong chairs made up of 1.2cm thick hot-pressed plywood for seat and back, upholstered with fabric upholstery covers and moulded polyurethane foam. BACK SIZE : 47.5 cm. (W) with SEAT SIZE : 47.0 cm. (W) x 48.0 cm. (D) The polyurethane foam is moulded with density = 45 ±2 kg/m and hardness = 20 ±2, on hampden machine at 25% compression. The one-piece armrests are injection moulded from black Co-polymer polypropylene.The chair shall have center tilt mechanism. The bellow is 3 piece telescopic type and injection moulded in black polypropylene. The pedestal is injection moulded in balck 30% glass-filled Nylon and fitted with 5 Nos. of Twin wheel castors. The twin wheel castors are injection moulded in 30% glass filled black Nylon etc., complete all as per Godrej Make or eqivalents of Wipro/Featherlite/Durian/Ergo/Ikea.

Supply of Seminar chair with writing pad made out of 25mm dia C.R. Pipe with powder coating finish with P.U. arms finish with seat and back with bended plywood with cushioned of 32 high density rubber foam for seat and back with fabric/leatherette or approved shade etc., with Writing Pad made with 18 mm thick ply wood etc all complete all as per Godrej make or equivalents of Wipro/ Feathrlite / Durian/ERGO.

Providing and fixing of Conference Table for 21 persons ,600 mm wide and 750 mm height made out of 18 mm thick plywood for frame work, shelf, foot rest and front facia, provision to accommodate conduits for wiring, front, top and side end surfaces to have 3.5 mm thick approved shade veneer paneling, exposed edges of ply wood covered with teak wood beading, exposed veneer of top shall be finished with melamine polish finish of approved shade, ends and fronts veneered surfaces finished with melamine polish, internal exposed surfaces of the table finished with two coats of enamel paint over one coat of wood primer including surface preparation etc., all complete as directed by Engineer -in-charge.

Supply of Pantry Table of size 2400x450x750mm made out of 18mm thick plywood with 1mm thick laminate top and sides,18mm thick granite cover on top two drawers and four shutters as shown in the drawing with spirit polish, including providing hardware fittings like hinges, ball catches etc complete as per drawing and as directed by engineer-in-charge.

Supply of Medical examination bench of size 1800mm x 900mm x 750mm made out of CRCA sheets of 18 gauage and 32mm dia pipe legs machine pressed double belt ER sheet two section top adjustable on sachet and legs fitted with four rubber feet, pre-treated and epoxy powder coated etc., complete all as per Model no :STHC3AE1C0000001 of godrej make or eqivalents of Wipro/Featherlite/Durian/ERGO

Supply of Patients waiting chair made out of 18 guage round pipe frame work with preforated sheet with powerder coating of approved shade etc., complete all as per Model no PERCH of godrej make or eqivalents of Wipro/Featherlite/Durian/ ERGO/Ikea.

Supply of semi fowler hospital bed of size 1980x910x 600 mm made out of M.S. rectangular tubes/ M.S channels having two section M.S.top uniformly perforated fixed to frame. Head and leg bows made from M.S tubular section having the machanism for lifting the part bed to upto 90 degrees angle with vertical bar's mounted on four synthetic rubber shoes including over backed finish all as per approved sample etc complete.

Supply of steel bed side locker of size 760x480x1266mm with 1 shelves at bottom making two compartments having double door, made out of body fabricated from 22 guage thick CRC MS plane sheets on top, bottom & doors and 20 guage thick CRC MS plane sheet on sides, back, & shelves, 19 mm dia hanging rod, locking arrangement with duplicate key of approved quality and powder coated etc complete Make Godrej or ERGO

Supply and placement of hard bed single wooden of size 1950 x 930 x 400mm made out of teak wood with side rail of size 120x30 mm. head board of size 930(width)X800(Ht) and foot board 930(width) x 400(Ht) made out of 70x30mm hard wood frame covered with 1mm thick laminate one side and other side 4mm thick commercial ply edges to have 40x6mm thick teak wood lipping and ,4 nos of 50 x 30 mm support of second class hard wood and 12mm thick commercial ply on bed top all finished melamine polish etc all complete as per drawing

Manufacture and supply of Rifile rack for 12 rifiles made out of 50mmm thick teak wood frame work with provision of individual holding & locking arrangments for the rifiles all complete with Spirit polish etc., complete.

Supply and placement of pegs set of 3 made out of 18mm plywood with 1 mm thick laminate with S/S pegs complete as per drawing.

Providing and fixing of cupboard of 600mm deep with 4 Nos. openable shutters, two vertical dividers and two shelves made out of 18mm ply wood with 1mm laminate board, all exposed edges to have teak wood lipping with spirit polish, including all necessary hardware fittings etc; all complete as per directions of engineer-in-charge.

Manufacture and supply of dressing unit for gents of size 1800 x 900 mm made out of 50x30 mm teakwood framework with 5mm thick mirror of approved quality and back with 6mm thick plywood etc., complete with spirit polish and all as per drawing.

Supply and fixing of reception counter of various size of 750X1050 mm height made out of 18mm plywood with 3.5 mm veneer for front, top and one No. storage unit to have one draw and one cupboard and two nos. of key board pull out tray, ail exposed edges to have molded teak wood beading, all hardware fitting in S/S finish all exposed surface with melamine polish complete.

Supply of Reception chairs made up of 1.2cm thick hot-pressed plywood for seat and back, upholstered with fabric upholstery covers and moulded polyurethane foam. BACK SIZE : 47.5 cm. (W) with SEAT SIZE : 47.0 cm. (W) x 48.0 cm. (D) The polyurethane foam is moulded with density = 45 ±2 kg/m and hardness = 20 ±2, on hampden machine at 25% compression. The one-piece armrests are injection moulded from black Co-polymer polypropylene.The chair shall have center tilt mechanism. The bellow is 3 piece telescopic type and injection moulded in black polypropylene. The pedestal is injection moulded in balck 30% glass-filled Nylon and fitted with 5 Nos. of Twin wheel castors. The twin wheel castors are injection moulded in 30% glass filled black Nylon etc., complete all as per Godrej Make or eqivalents of Wipro/Featherlite/Durian/Ergo/Ikea.

SUB HEAD-XX : AIR CONDITIONING

HI WALL/CASSETTE TYPE/TOER SPLIT UNIT

Supply, Testing and commissioning of HI WALL/CASSETTE TYPE/TOER SPLIT / VRV Compatibility UNIT with indoor and out door units with invertor rotatry compressor including proper mounting arrangement and accessories, Indoor unit comprises of pre filter, coil section, evaporator section, low noise multi speed fin, all refrigerant neccesary & mounting stand for our door unit including standard copper piping (3 mtrs) suppled with R410A refrigerant with 5 years machine and 10 years compressor warranty and 5 star rating.

Supply, installation, testing and commissioning of a mutifunctional compact centralized Intellegent self Programmable controller. It shall be able to control minimum 64 indoor units. The controller shall have wide screen user friendly colour LED/ LCD display and can be wired by a non polar 2 wire transmission cable to a distance of 1 km away from indoor unit including necessary fixing arrangment to the desiared location and necessary control wiring from all indoor units to CIRTC and from all out door units to CIRTC and Software and hardware required to operate from end user system and povide MODBUS/ BACNET OUTPUT for IBMS integration with IP RS 485 compactability. The external wiring and inside wiring shall run suitable size conduit all as specified and / or directed etc., complete.

LOW SIDE WORKS

Supply and laying of Communication / Control cable connecting the Indoor units / Outdoor units / Controller of suitable size as recommended by the OEM. The external communication / control cabling shall be run in MS conduit and inside building control cabling shall be run in PVC conduit including all clamps, screws, fittings, supporting items etc., all as specified and/or directed etc., complete. Note: 1) The cost for MS and PVC conduit shall be measured and paid seperately under relevant item of SOQR

Supply, erection, testing and commissioning of size6.4 mm dia refrigerant grade copper piping of 20 gauge including nitrile rubber tubular insulation with factory laminated glass cloth, adhesive tape, including all kinds of valves / joints viz., refnet joint / header, refrigerant joint / header, distribution / branch unit, tees, valves, ball valves, fittings like bends, elbow, collars, tees, reducers, flanges, supports, etc for interconnecting the liquid and suction lines between the outdoor units and the indoor units and flare connection to indoor units. Refrigerant joints supplied by OEM only shall be used. The piping shall be carried out of soft / hard drawn copper pipes brazed socket fittings. Both the suction and liquid lines shall be insulated with closed cell nitrile rubber tubular insulation of thickness as specified in tender including pressure testing and charging of refrigerant and oil. Refrigerant piping and cables in wall crossings shall be provided in suitable steel / PVC sleeve all as specified and/ or directed etc., complete. Note: 1) Only the cable tray supports provided for exposed refrigerant pipes will be measured and paid under the relevant item of SOQR.

Supply, erection, testing and commissioning of size 9.5 mm dia refrigerant grade copper piping of 20 gauge including nitrile rubber tubular insulation with factory laminated glass cloth, adhesive tape, including all kinds of valves / joints viz., refnet joint / header, refrigerant joint / header, distribution / branch unit, tees, valves, ball valves, fittings like bends, elbow, collars, tees, reducers, flanges, supports, etc for interconnecting the liquid and suction lines between the outdoor units and the indoor units and flare connection to indoor units. Refrigerant joints supplied by OEM only shall be used. The piping shall be carried out of soft / hard drawn copper pipes brazed socket fittings. Both the suction and liquid lines shall be insulated with closed cell nitrile rubber tubular insulation of thickness as specified in tender including pressure testing and charging of refrigerant and oil. Refrigerant piping and cables in wall crossings shall be provided in suitable steel / PVC sleeve all as specified and/ or directed etc., complete. Note: 1) Only the cable tray supports provided for exposed refrigerant pipes will be measured and paid under the relevant item of SOQR.

Supply, erection, testing and commissioning of size 12.7 mm dia refrigerant grade copper piping of 20 gauge including nitrile rubber tubular insulation with factory laminated glass cloth, adhesive tape, including all kinds of valves / joints viz., refnet joint / header, refrigerant joint / header, distribution / branch unit, tees, valves, ball valves, fittings like bends, elbow, collars, tees, reducers, flanges, supports, etc for interconnecting the liquid and suction lines between the outdoor units and the indoor units and flare connection to indoor units. Refrigerant joints supplied by OEM only shall be used. The piping shall be carried out of soft / hard drawn copper pipes brazed socket fittings. Both the suction and liquid lines shall be insulated with closed cell nitrile rubber tubular insulation of thickness as specified in tender including pressure testing and charging of refrigerant and oil. Refrigerant piping and cables in wall crossings shall be provided in suitable steel / PVC sleeve all as specified and/ or directed etc., complete. Note: 1) Only the cable tray supports provided for exposed refrigerant pipes will be measured and paid under the relevant item of SOQR.

Supply, erection, testing and commissioning of size 15.9 mm dia refrigerant grade copper piping of 20 gauge including nitrile rubber tubular insulation with factory laminated glass cloth, adhesive tape, including all kinds of valves / joints viz., refnet joint / header, refrigerant joint / header, distribution / branch unit, tees, valves, ball valves, fittings like bends, elbow, collars, tees, reducers, flanges, supports, etc for interconnecting the liquid and suction lines between the outdoor units and the indoor units and flare connection to indoor units. Refrigerant joints supplied by OEM only shall be used. The piping shall be carried out of soft / hard drawn copper pipes brazed socket fittings. Both the suction and liquid lines shall be insulated with closed cell nitrile rubber tubular insulation of thickness as specified in tender including pressure testing and charging of refrigerant and oil. Refrigerant piping and cables in wall crossings shall be provided in suitable steel / PVC sleeve all as specified and/ or directed etc., complete. Note: 1) Only the cable tray supports provided for exposed refrigerant pipes will be measured and paid under the relevant item of SOQR.

Supply, erection, testing and commissioning of size 19.1 mm dia refrigerant grade copper piping of 20 gauge including nitrile rubber tubular insulation with factory laminated glass cloth, adhesive tape, including all kinds of valves / joints viz., refnet joint / header, refrigerant joint / header, distribution / branch unit, tees, valves, ball valves, fittings like bends, elbow, collars, tees, reducers, flanges, supports, etc for interconnecting the liquid and suction lines between the outdoor units and the indoor units and flare connection to indoor units. Refrigerant joints supplied by OEM only shall be used. The piping shall be carried out of soft / hard drawn copper pipes brazed socket fittings. Both the suction and liquid lines shall be insulated with closed cell nitrile rubber tubular insulation of thickness as specified in tender including pressure testing and charging of refrigerant and oil. Refrigerant piping and cables in wall crossings shall be provided in suitable steel / PVC sleeve all as specified and/ or directed etc., complete. Note: 1) Only the cable tray supports provided for exposed refrigerant pipes will be measured and paid under the relevant item of SOQR.

Supply, erection, testing and commissioning of size 22.2 mm dia refrigerant grade copper piping of 20 gauge including nitrile rubber tubular insulation with factory laminated glass cloth, adhesive tape, including all kinds of valves / joints viz., refnet joint / header, refrigerant joint / header, distribution / branch unit, tees, valves, ball valves, fittings like bends, elbow, collars, tees, reducers, flanges, supports, etc for interconnecting the liquid and suction lines between the outdoor units and the indoor units and flare connection to indoor units. Refrigerant joints supplied by OEM only shall be used. The piping shall be carried out of soft / hard drawn copper pipes brazed socket fittings. Both the suction and liquid lines shall be insulated with closed cell nitrile rubber tubular insulation of thickness as specified in tender including pressure testing and charging of refrigerant and oil. Refrigerant piping and cables in wall crossings shall be provided in suitable steel / PVC sleeve all as specified and/ or directed etc., complete. Note: 1) Only the cable tray supports provided for exposed refrigerant pipes will be measured and paid under the relevant item of SOQR.

Supply, erection, testing and commissioning of size 28.6 mm dia refrigerant grade copper piping of 18 gauge including nitrile rubber tubular insulation with factory laminated glass cloth, adhesive tape, including all kinds of valves / joints viz., refnet joint / header, refrigerant joint / header, distribution / branch unit, tees, valves, ball valves, fittings like bends, elbow, collars, tees, reducers, flanges, supports, etc for interconnecting the liquid and suction lines between the outdoor units and the indoor units and flare connection to indoor units. Refrigerant joints supplied by OEM only shall be used. The piping shall be carried out of soft / hard drawn copper pipes brazed socket fittings. Both the suction and liquid lines shall be insulated with closed cell nitrile rubber tubular insulation of thickness as specified in tender including pressure testing and charging of refrigerant and oil. Refrigerant piping and cables in wall crossings shall be provided in suitable steel / PVC sleeve all as specified and/ or directed etc., complete. Note: 1) Only the cable tray supports provided for exposed refrigerant pipes will be measured and paid under the relevant item of SOQR.

Providing and laying of cPVC (SDR11) pipes of 32 mm dia, with 9 mm thick elastomeric nitrile rubber tubular insulation with FRP/ Glass cloth rapped over insulation for condensate water drain from the AC indoor units to nearest drain point, fittings, support including core cutting in brick/ concrete wall as required and making surface good etc. complete .

Providing and laying of cPVC (SDR11) pipes of 25 mm dia, with 9 mm thick elastomeric nitrile rubber tubular insulation with FRP/ Glass cloth rapped over insulation for condensate water drain from the AC indoor units to nearest drain point, fittings, support including core cutting in brick/ concrete wall as required and making surface good etc. complete .

Supply and Laying of Control and communication cable for connecting the IDUs and ODUs (Control wiring using 4C X 2.5 Sq.mm copper cable) with conduit of required size.Complete as per site requirement

Supply and Laying of Control and communication cable for connecting the IDUs and ODUs (Control wiring using 3C X 1.5 Sq.mm copper cable) with conduit of required size.Complete as per site requirement

Supply and Laying of Control and communication cable for connecting the IDUs and ODUs (Control wiring using 2C X 0.75 Sq.mm copper cable) with conduit of required size. Complete as per site requirement

Supply, fabrication and installation for MS angle base frame structure duly black painted with synthetic epoxy paint for VRV Outdoor units. The frame structure shall be mounted on MS plate & serrated rubber pads all as specified and / or directed etc., complete. (28 HP)

Supply, installation, testing and commissioning of initial Charge of refrigerant gas - R 410 A, Pressure testing of the entrire system with Nitrogen and vaccumizing the nitrogen

Supply and erection of Drain pump for DX - Hiwall units with neccesary supports for installtion.

Supply and erection of M.S. angle stand with synthetic epoxy paint for all outdoor units for installation of DX - Hiwall units.

Supply and erection of M.S. angle stand with synthetic epoxy paint for all outdoor units for installation of DX - Cassette units.

SUB HEAD-XXI : SPECIAL EARTHING

Supply of CPRI tested maintenance free ,Low carbon mild steel copper coated earth rod of 3 metre electrode having diameter of 14.2 mm with copper coating thickness of 250micron tested as per IEC 62561-2 & is provided with universal clamp made of SS to connect rod with flat conductor. Earth conductivity enhancing compound shall be of 25 kg/pit tested as per IEC 62561-7,TCLP tested. The above arrangements shall be provided with Heavy duty earth champer of 5000kg load bearing capacity to ensure the safety of earthing system.

Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing as required

Providing and fixing earth bus of 50x6mm Hot Dip Galvanized GI strip

Providing and fixing earth bus of 25x6mm Hot Dip Galvanized GI strip

Providing and fixing 25 mm X 5 mm copper strip on surface or in recess for connections etc. as required.

Supply, installation, testing and commissioning of lockable terminal box in 1.6mm thick with MS enclosure with transperant cover with 2 no. (600 mm length) 50 x 6 mm copper strip on epoxy insulators with required. 8mm dia holes with 8mm x 25mm dia brass nut bolt with double washer.

SUB HEAD-XXII : LIGHTNING PROTECTION

Supply and laying of 8 mm Aluminum Round Conductor complete as specified in drawing.

Supply and fixing of Roof conductor holder for parapet- Polyamide Conductor holder with M8 female thread or diameter 7mm, M8 Screw to connect the conductor holder. Weather and temperature resistant from -35 to +90 degree Celsius tested. Conductor holder @ 1 meter distance.

Supply and fixing of Polyamide roof cable holder for flat roof and Closed form with bottom. Filling weight 1Kg (frost-resistant concrete). Sleeve from polyethylene, black @ 1 meter distance.

Supply and fixing of Conductor holder for sheet as specified in drawing, Bottom section stainless steel with Ø 8.5 mm slot made of Conductor holder of stainless steel @ every 1mtr distance.

Supply and fixing of cross universal connector for T and cross connection, to route vertical down conductor /mesh formation made of hot dipped galvanised iron with necessary screws etc as required. Installed with 4 hexagonal bolts M8*25 with M8 hexagonal nuts.

Supply and fixing of expansion piece with connector for equalising temperature related length changes and necessary on conductors length over 20 meters (for round conductor Rd 8/ALU)

Supply and fixing of T cross and parallel connectors for Quick installation using hexagonal bolt M10X30 high-grade hot dip galvanised. (2nos/expansion piece ).

Supply and fixing of 4 mtr Vertical air terminal as per IS-IEC -62305 part-3 16mm rod tapered to 10 mm aluminium rod with suitable for high wind load.

Supply and fixing of Fang fix with base and clamp made of SS, lightning tested for 100 KA 10/350 micro sec waveform.16 KG stone of 365 mm diameter, high level of stability.Quick and easy mounting of interception rod using anchors and top air terminal.Concrete, frost-resistant, can be stacked.

Down Conductor

Supply and fixing of Test Joint (Folding Clamp) suitable to connect 8mm round conductor and max by 30x3 mm GI strip and with enclosure RoHS Complied, IP66, 6mm², 500V, IK08, UV resistant, Halogen free Thermoplastic junction box ,installation of cables either directly through the 7 x M25 seals, polypropylene,Light grey.Junction box T 100, plug-in seal Clear internal dimensions: 136x102x57 mm as specified in drawing and directed by Engineer

Supply testing,installation and commisioning of Lightning counter to count no of lightning strike & it can record the date and time of the lightning incident also tested as per IEC 62561-6.

Supply and laying of Galvanised Steel Flat 30X3 mm thickness from earth electrode directly in ground as required. Flat conductor shall be of Hot Dipped & Cross sectional area of 90mm square with Zinc coating: 500 g/m square should be tested and used exclusively for lightning protection earthing system and ring equipotential bonding.

Supply and fixing of Flat Cross connector suitable for 30mm Galvanised steel strip. Installed with 4 nos of hexagonal plate.

Supply and fixing of flat conductor holder suitable for FL 30. Installed with 2 hexagonal bolts.

Supply and fixing of Plastic Corrosion Protection strip: Approx 1.1 mm thick. Width 50mm. Made of petrolatum- coated chemical fibre fabric.

Supply and installation of CPRI tested maintenance free ,Low carbon mild steel copper coated earth rod of 3 metre electrode having diameter of 17.2 mm with copper coating thickness of 250micron tested as per IEC 62561-2 & is provided with universal clamp made of SS to connect rod with flat conductor.Earth conductivity enhancing compound shall be of 50 kg/pit tested as per IEC 62561-7,TCLP tested.The above arrangements shall be provided with Heavy duty earth champer of 5000kg load bearing capacity to ensure the safety of earthing system

Supply and fixing of earth fixed point made of Stainless Steel, grade 316L. Connection to earthing systems, air terminals and reinforcement. Contact plate: 79 mm diameter, made of rustproof stainless steel (V4A). Clamping bolt 10mm diameter, rustproof Including plastic cover for simple installation.

Supply and fixing of cross connector for reinforcement, Flat galvanised steel and earth fixed point. This connects earth fixed point to reinforcement and installed with screws M10x40.

Supply and fixing of connector to connect air terminal with earth fixing point.

Supply and fixing of folding clamp to hold 8 mm Al conductor at every 1m dist on the top roof without any drilling on roof , Installation can be made through simple fastening system ,mainly used for seaming sheet roof application, Holds good upto seaming thickness of upto 20mm .

SUB HEAD-XXIII : FIRE ALARM & FIRE EXTINGUISHERS

Supplying, installing, testing and commissioning approved make Addressable Multi-criteria Photo-Thermal Detector with sensitivity range of 0.5 to 4.0% obs/ft.The intelligent multi criteria detection device shall include the ability to combine the signal of the thermal sensor with the signal of the photoelectric signal in an effort to react hastily in the event of a fire situation. It shall also include the inherent ability to distinguish between a fire condition and a false alarm condition by examining the characteristics of the thermal and smoke sensing chambers and comparing them to a database of actual fire and deceptive phenomena. The detector shall have twin bi-colour LED for 360 deg viewing. Addressing shall be with user friendly rotary decimal switches. The detector sensitivity (day & night) shall be controlled from the panel to get accustomed to the local environment.The detector shall comply UL268, 7th Edition guidelines. Detector Must be UL & FM Approved.

Supply installation Testing and commissioning of Response indicators with LED Indication lamp.

Supplying, installing, testing and commissioning approved make Isolator Module for Isolating short / dewired / loose circuits with automatic resetting arrangement. Isolator Base can also be proposed, however in that case needs to be considered with each detector & module. The device shall have an LED which shall blink in normal state & get steady on activation to monitor the heath status of the device. Module shall be supplied with mounting plate from OEM for ease of installation & maintenance

Supplying, installing, testing and commissioning approved make Addressable Manual pull station. The device shall have an LED which shall blink in normal state & get steady on activation to monitor the heath status of the device. The device shall comply UL & FM approval.

Supply and fixing of emergency Exit Light fixtures with 2 hrs battery back up using SMF Battery.complete with required accessories. - Minimum Size 600 x 300 both sides transparent- Prolite / Glolite make. It shall be ceiling / wall mounting suitable to site condition complete with required accessories.

Supply and installation of 1.5 Km range Siren with Weather proof motor with 220V 50HZ AC Supply operation with required power contactor, MPCB for control all in a weather proof enclosure near motor including all installation materials as required

Supplying, installing, testing and commissioning approved make Network Repeater Panel with minimum 10" Color Touch Screen display/ QWERTY Keypad, mapping minimum 2,00,000 points on network. The NRP shall act as an independent node communicating on the peer to peer network and shall not be dependant on the Fire Panel CPU for operation. Failure of Fire Panel CPU shall not result in failure of NRP operation.

Supplying, installing, testing and commissioning approved make Graphics User Interface for Monitoring & Control of complete Fire, Voice Evacuation & Telephone Talkback System. The GUI based main network software shall network with other panels on True Peer-to-Peer network. It shall be capable of graphically representing each facility being monitored with floor plans and icons depicting the actual locations of the various systems, and / or sensors’ locations. It shall have the facility to change the sensitivity of any detector. The software shall be capable of monitoring 200 Nodes with 100 Mbps Transmission rate on Fibre Optics Network and 12 Mbps Transmission on cable and 2,50,000 network points. The software shall be capable to Monitor & Control all the Digital Voice Evactuation as well as 2 way communication from main control room using voice signals over Fire Network along with the Fire detection signal. The Graphic workstation shall act as an independent node communicating on the peer to peer network and shall not be dependant on the Fire Panel CPU for operation. Failure of Fire Panel CPU shall not result in failure of GUI.

Supplying, installing, testing and commissioning approved make MODbus Interface Gateway for communication with BMS / Other Utilities. MODbus shall support minimum 14000 data points. MODbus Gateway shall act as an independent node communicating on the peer to peer network and shall not be dependant on the Fire Panel CPU for operation.

True on line UPS system with following specs.

a) Input voltage 170V AC to 250V AC

b) Output voltage 230V AC+/-1%

c) Output capacity-1KVA

d) Battery backup of 30 minutes with suitable SMF batteries

Supply and laying of twisted pair 2C X 1.5sq.mm shielded FRLS insulated copper conductor flexible wire through existing MS Conduit complete with required accessories.

Supply and drawing of 2 C X 2.5 Sq mm multi stranded twisted shielded FRLS Copper cable.

Supply and fixing of 25mm dia 1.6 thick MS conduit run on surface of wall/Ceiling/above false ceiling and all fixing accessories in complete. The conduit in walls shall be concealed by chasing and finishing back complete with required accessories.

Supply and laying of 3core 2.5sq.mm Copper conductor PVC insulated FRLS armoured cable for connectivity of the siren complete with required accessories.

Supplying laying testing and Commissioning of Single mode Fiber Cable Outdoor Unitube/Multitube Single Sheathed Armoured with Steel Wire for network backbone across various buildings in cable tray /conduit and periphery of the unit, underground in the open areas as per requirment.

Supply and installation of ABC 6KG DRY CHEMICAL POWDER EXTINGUISHER with 4 leg stand,Fire Extinguisher Mono Ammonium Phosphate Powder 90,Stored Pressure Type, Pressure Gauge,Gross Wieght 8 Kg Empty Weight 3 Kg,Can hieght 449mm,Diameter 150mm, Discharge time less than 15secs, Controllable discharge mechanism,range minimum 4 Mtrs, Applicable on Class A,B,C and Electrical started fire ,A Rating-21A,B Rating 89B, Conforms to ISI Standards&EN Approved,Can construction Deep drawn and CO2 Mig welded,Valve construction Forging and machining ,Internal coating of can Epoxy powder coating, External Coating of can Epoxy Polyester Powder Coating, Sheet Metal Thickness 2mm,Helium Leak Detection tested,as per IS 13849. This shall also include the Auto glow fire extinguisher type identification wall mount signage 150 x 400mm along with the fire extinguisher.

Supplying, installing, testing and commissioning approved make Addressable Loop Powered Autoaligned Beam Detector. The beam detector shall be used for High Ceiling application with a detection range from 5 upto 100 mtrs and highly resistant to building movement; tolerates +/- 1° movement, Resistant to solid object intrusion, , Built-in imager heater, Resistant to strong light sources; does not alarm when saturated by sunlight, Automatic sensitivity threshold level settings and drift compensation. The detector shall be IP-55 compliant. Must be UL & FM Approved.

Supply and installation of CO2-4.5Kg Squeeze Grip- 4.5 Kg ,CO2 Gas Type Fire Extinguisher, standard Trolley Mounted,easy Weight Management , Used Unused Mechanism, Squeeze Grip, Gross Weight 19.1Kg, Empty Weight 14.6Kg,Can Height 857MM,Diameter 140MM,Discharge Time less than 10 Secs, controllable disharge mechanism, Applicable on Class B&C Fires, B Rating 55B, Can Construction:Hot Spinning/Forging,Valve Construction: Forging and Machining, Internal Coating of Can: NA, External Coating of Can: Spray Painting ,Sheet Metal Thickness:4.5MM, ISI & DOE Approved, 1Year Warranty. DOE Approved. This shall also include the Auto glow fire extinguisher identification wall mount signage 150 x 400mm along with the fire extinguisher.

Supply installation testing and commissioning of Water-9 Ltr Stored Pressure type Fire Extinguisher, Pressure Guage, Gross Weight 14.6 Kg, Empty Weight 5.6 Kg, Can Height 611MM, Diameter 175MM, Discharge Time Less than 120 secs, Controllable discharge mechanism, Range minimum 6 Meters, Applicable on Class A Fire, A Rating 21A, Can Construction : Deep Drawn & CO2 Mig welded, Valve Construction: Forging & Machining, Internal Coating of Can: Epoxy Powder Coating, Extranal Coating of Can : Epoxy Polyster Powder Coating, Sheet Metal Thickness :2.00MM, ISI and CE Approved,Hileum Leak Detection tested. This shall also include the Auto glow fire extinguisher identification wall mount signage 150 x 400mm along with the fire extinguisher.

Fire Point at 4 places with proper MS shed and 4 fire beaters and 4 fire buckets with sand and 4 fire buckets with water along with the FE's mentioned below:

Supply and installation of Fire Point consists of following fire Extinguishers near reception, all housed in the enclosure

Mechanical foam Fire Extinguisher

SUB HEAD-XXIV : FIRE FIGHTING

Hydrant system

Electrical operated pumps

Supply, erection, testing and commissioning of Electrical operated Fire pump of horizontal split casing type with a speed of 1440 RPM and of capacity 2850 LPM against a total head of 70 mtrs, complete with TEFC Motor class- F insulation suitable for the pump, base plate, coupling, coupling guard ,foundation bolts and nuts etc., complete. (The pump shall be capable of furnishing not less than 150% of the rated discharge at a head not less than 65% of the rated head and the shut-off head shall not exceed 120% of rated head as per TAC guidelines)

Moc: CI casing, Bronze Impeller

Diesel Engine pumps

Moc: CI casing, Bronze Impeller

Jockey pump

Supply, erection, testing and commissioning of Jockey pump of 500 LPM with a speed of 2900 RPM against a total head of 70 mtrs, complete with TEFC Squirrel Cage motor with class- F insulation suitable for the pump, base plate, coupling, coupling guard foundation bolts and nuts etc., complete.

Moc: CI casing, Bronze Impeller

Supply installation testing and commissioning of Fire brigade inlet with 4 built in inlets with NRV and One Sluice valve with glass cover box and interconnections suitable for working pressure.

Supply and fixing of Air Cushion vessel in Fire pump room with Drain and Safety valves made out of 8 mm thick 2.5 Mtr long 300 mm dia MS pipe.

Supply, laying, testing and commissioning of centrifugally Cast Ductile Iron pipes conforming to IS 8329 class K9, with Cement Mortar lining inside suitable for all types of sockets and spigot type joints and of following sizes including supply and fixing of all push on type/ mechanical joints conforming to IS 13382 along with Jointing materials such as Bends, Elbows, Tees, Flanged Spigots, Collars, etc. and making Tyton joints to DI Pipes, specials and labour charges, testing the joints for leakage and making good if any for hydrant system.

Supply, erection, testing and commissioning of pressure switches for fire fighting pumping system.

Supply, erection, testing and commissioning of pressure Gauges with range of 0-15 bar along with isolation cock and pipe at hydrant station for fire fighting pumping system.

Supply, laying, testing and commissioning of C-class MS pipes conforming to IS 1239 upto 150 NB and IS 3589 from 200 NB including all required bends, fittings, flanges, bolts, nuts, welding of joints and painting with two coats of postal red enamel paint over one coat of primer etc., complete and of following sizes:

250 NB (6 mm thick)

Providing anti corrosive Wrapping and coating with 4 mm thick bitumastic membrane (Pypkote) for DI pipe laid below ground including all materials with minimum overlapping of 30 mm.

Supplying & fixing, testing & commissiong of 150MM DIA (RUBBER BELLOW) expansion bellows shall be provided on both suction & delivery side of pumps as required, this will enable to negotiate minor vibration during pump operation. Pressure rating of bellows shall be PN-10, PN-16 & PN-25 rating. Low Zone - PN 16

Supplying & fixing, testing & commissiong of 125MM DIA (RUBBER BELLOW) expansion bellows shall be provided on both suction & delivery side of pumps as required, this will enable to negotiate minor vibration during pump operation. Pressure rating of bellows shall be PN-10, PN-16 & PN-25 rating. Low Zone - PN 16

Supplying & fixing, testing & commissiong of 80MM DIA (RUBBER BELLOW) expansion bellows shall be provided on both suction & delivery side of pumps as required, this will enable to negotiate minor vibration during pump operation. Pressure rating of bellows shall be PN-10, PN-16 & PN-25 rating. Low Zone - PN 16

Supplying & fixing, testing & commissiong of 65MM DIA (RUBBER BELLOW) expansion bellows shall be provided on both suction & delivery side of pumps as required, this will enable to negotiate minor vibration during pump operation. Pressure rating of bellows shall be PN-10, PN-16 & PN-25 rating. Low Zone - PN 16

Supply, fixing, testing and commissioning of All Socketed Tee 150 mm x150 mm x 150 mm dia centrifugally Cast Ductile Iron fittings/Specials (Socket and Spigot type) conforming to IS 9523: 2000, Class K9, with Cement Mortar Lining (CML) as per IS 455: 1989 inside and bituminous coated outside ISI marked such as Bends, Elbows, Tees, Flanged Spigots, Collars, flanges (flange rating PN 16) etc testing the joints for leakage (if any) and making good hydrant system.

Note : DI Specials mentioned below are to be procured as per actual site conditions and as required only. Full payment will be released only for the specials fixed and erected at the site of work, as directed by the Engineer-in-Charge.

Supply, fixing, testing and commissioning of Double Socketed Tee with Flanged Branch 150 mm x 150 mm x 150 mm dia centrifugally Cast Ductile Iron fittings/Specials (Socket and Spigot type) conforming to IS 9523: 2000, Class K9, with Cement Mortar Lining (CML) as per IS 455: 1989 inside and bituminous coated outside ISI marked such as Bends, Elbows, Tees, Flanged Spigots, Collars, flanges (flange rating PN 16) etc testing the joints for leakage (if any) and making good hydrant system.

Supply, fixing, testing and commissioning of All Socketed 90deg bend 150 mm dia centrifugally Cast Ductile Iron fittings/Specials (Socket and Spigot type) conforming to IS 9523: 2000, Class K9, with Cement Mortar Lining (CML) as per IS 455: 1989 inside and bituminous coated outside ISI marked such as Bends, Elbows, Tees, Flanged Spigots, Collars, flanges (flange rating PN 16) etc testing the joints for leakage (if any) and making good hydrant system.

Supply, fixing, testing and commissioning of All Socketed 45deg bend 150 mm dia centrifugally Cast Ductile Iron fittings/Specials (Socket and Spigot type) conforming to IS 9523: 2000, Class K9, with Cement Mortar Lining (CML) as per IS 455: 1989 inside and bituminous coated outside ISI marked such as Bends, Elbows, Tees, Flanged Spigots, Collars, flanges (flange rating PN 16) etc testing the joints for leakage (if any) and making good hydrant system.

Supply, fixing, testing and commissioning of All socketed 22.5deg. bend 150 mm dia centrifugally Cast Ductile Iron fittings/Specials (Socket and Spigot type) conforming to IS 9523: 2000, Class K9, with Cement Mortar Lining (CML) as per IS 455: 1989 inside and bituminous coated outside ISI marked such as Bends, Elbows, Tees, Flanged Spigots, Collars, flanges (flange rating PN 16) etc testing the joints for leakage (if any) and making good hydrant system.

Supply, fixing, testing and commissioning of All socketed 11.25deg. bend 150 mm dia centrifugally Cast Ductile Iron fittings/Specials (Socket and Spigot type) conforming to IS 9523: 2000, Class K9, with Cement Mortar Lining (CML) as per IS 455: 1989 inside and bituminous coated outside ISI marked such as Bends, Elbows, Tees, Flanged Spigots, Collars, flanges (flange rating PN 16) etc testing the joints for leakage (if any) and making good hydrant system.

Supply, fixing, testing and commissioning of Reducer socket 200mm dia centrifugally Cast Ductile Iron fittings/Specials (Socket and Spigot type) conforming to IS 9523: 2000, Class K9, with Cement Mortar Lining (CML) as per IS 455: 1989 inside and bituminous coated outside ISI marked such as Bends, Elbows, Tees, Flanged Spigots, Collars, flanges (flange rating PN 16) etc testing the joints for leakage (if any) and making good hydrant system.

Supply, fixing, testing and commissioning of Socketed collar 150 mm dia centrifugally Cast Ductile Iron fittings/Specials (Socket and Spigot type) conforming to IS 9523: 2000, Class K9, with Cement Mortar Lining (CML) as per IS 455: 1989 inside and bituminous coated outside ISI marked such as Bends, Elbows, Tees, Flanged Spigots, Collars, flanges (flange rating PN 16) etc testing the joints for leakage (if any) and making good hydrant system.

Supply, fixing, testing and commissioning of Flanged Socket 150mm dia centrifugally Cast Ductile Iron fittings/Specials (Socket and Spigot type) conforming to IS 9523: 2000, Class K9, with Cement Mortar Lining (CML) as per IS 455: 1989 inside and bituminous coated outside ISI marked such as Bends, Elbows, Tees, Flanged Spigots, Collars, flanges (flange rating PN 16) etc testing the joints for leakage (if any) and making good hydrant system.

Supply, fixing, testing and commissioning of Flanged Spigot 150 mm dia centrifugally Cast Ductile Iron fittings/Specials (Socket and Spigot type) conforming to IS 9523: 2000, Class K9, with Cement Mortar Lining (CML) as per IS 455: 1989 inside and bituminous coated outside ISI marked such as Bends, Elbows, Tees, Flanged Spigots, Collars, flanges (flange rating PN 16) etc testing the joints for leakage (if any) and making good hydrant system.

Providing push-on-joints to Centrifugally (Spun) Cast Iron Pipes or Ductile Iron Pipes including testing of joints and the cost of rubber gasket

Fabrication,Supply,testing and commissioning coupler of DI to MS of 150mm dia / or directed by engineer incharge with all required accessories etc. complete

Fabrication,Supply,testing and commissioning coupler of MS to DI of 150mm dia / or directed by engineer incharge with all required accessories etc. complete

Supply, erection, testing and commissioning of GM gate valves (PN-16) with threaded ends and conforming to IS 778 and of following sizes:

Supply,erection,testing and commissioning of Cast Iron Sluice Valves with S.S Disc: Wheel operated conforming to IS:14846, PN 16 with flanges for pipe including bolts,nuts and rubber insertions etc., complete and of following sizes:

Supply, erection, testing and commissioning of Cast Iron Butterfly Valves (Wafer Type) with S.S.Disc: Lever operated conforming to IS: 13095: 1995, PN 16 with flanges for pipe and valve including bolts, nuts and rubber insertions etc., complete and of following sizes:

Supply, erection, testing and commissioning of double flanged swing check valves (non Return PN-16) conforming to IS 5312 complete with bolts, nuts and rubber insertions and of following size:

Supply, erection, testing and commissioning of Double Headed Fire Hydrant with 63 mm female instantaneous outlet in oblique type complete with cap & chain generally as per IS 5290.

Supply, erection, testing and commissioning of Single Headed Fire Hydrant with 63 mm female instantaneous outlet in oblique type complete with cap & chain generally as per IS 5290.

Supply & fixing 63 mm dia Cotton Synthetic Fibre (RRL) Woven rubber lined fire hose treated against rot with MYSTOX, conforming to IS 636 type 'A' bounded with male and female instantaneous G.M. couplings and of length of 30 M.

Supply & fixing 63 mm dia Cotton Synthetic Fibre (RRL) Woven rubber lined fire hose treated against rot with MYSTOX, conforming to IS 636 type 'A' bounded with male and female instantaneous G.M. couplings and of length of 15 M.

Supply and fixing of Gun Metal branch pipe 63 mm dia, male and female threaded outlet complete with hexagonal base bore nozzles as per IS 903.

Supply and fixing of hose reel of 30 m long of thermoplastic synthetic hose (IS:12585) of 19 mm dia with 15-20 mm dia nozzle including swinging type drum with all necessary bolts, nuts etc., complete.

Supply and fixing of Fire Hose Cabinet of MS size 2½ 'x 2½' x 1' to accommodate First aid hose reel of 30 meters long, glass fronted, Single door with lock painted fire red outside with suitable structural support complete but excluding civil works.

Supply and fixing of Fire Hose Box of MS of size 3 'x 2' x 1' 6” to accommodate two numbers of 30 M/15M length hoses and branch pipe, glass fronted, double door with lock painted fire red outside with suitable structural support complete but excluding civil works.

Supply installation testing and commissioning of 250 mm dia Y- type strainer (with Magnetic elemet) with all necessary flanges, bolts, nuts etc., complete.

Supply, installation, testing & commissioning of Pressure Gauge 0 - 30 kg/cm² with brass knob on pipes with using a long threaded GI Socket duly welded as per system requirement for different pipe sizes as directed.

Supply, fabrication, fixingand testing of MS puddle flanges of required sizes for out pipes for fire sump. The puddle flanges shall be flanged ends, of the following size.

Supply, erection, testing and commissioning of Brass/ GM/ Bronze Air release valves screwed end type and rubber insertions etc., complete and of following size:

Suppy, installation, testing, Design, manufacture, supply inspection, handling, assembling, affecting proper connections, testing and commissioning of 16 SWG CRCA sheet steel fabricated cubical type Fire Panel ,floor mounting, dust & vermin proof, front operated construction, enclosure class - IP 42, powder coated after proper treatment with 9 tank process with top/bottom removable gland plates, as required, double compression type cable glands, earth bus, hinged and lockable doors to achieve dust and vermin proof complete with all inter connections small wiring by min. 2.5 sq. mm. FRLS copper wires, ckt labels etc. The Aluminium Bus Bar shall be of suitable length, 415 volts, 3 phase 50 Hz TPN(4W), with withstanding impulse voltage 12kV. The panel feeders shall be suitable for terminating suitable nos. 3.5 / 4 core armoured aluminium cable or Aluminium Bus Duct as required.

160A MCCB Incomer: 1 Sets

160A 4P 25KA Motorised MCCB Microprocessor based release unit with overload (adjustable), short circuit (fixed magnetic) & earth fault protection release with potential free contact and extended rotary handle - 01 Nos

3 CT's of ratio 160/5A, Class 1.0 accuracy 15 VA burden for metering. - 1 Set

LED type phase indicating lamps, each lamp shall be with backup MCB, auxillary relay, 2 sets of push buttons. - 3 Nos

LED type indicating lamp for indicating the status of feeder - ON / OFF / TRIP.Each lamp shall be with backup MCB. - 3 Nos

OUTGOINGS

150A MPCB 50KA with contactor of 150A and DOL starter ,overload, short circuit & earth fault protection release - 01 Nos

32A MPCB 50KA with contactor of 32A and DOL starter ,overload, short circuit & earth fault protection release - 02 Nos

32A DP MCB - 01 Nos

Type II SPD 25kA/Phase with suitable MCCB - 1 Set

BUS BARS

160 AMP ,415 Volts, 3 phase 50 HZ,TPN(4W),25kA, high conductivity Aluminium bus bar of suitable length, SMC / DMC supports, with colour coding and insulated by heat shrinkable sleeves and clip on shrouds for joints.The current density of bus bar shall be as per TTA design certified to IEC 61439.

All Incomers & Outgoings Cable Entry From Top/bottom

Suitable Gland Plate To Be Provided For Each Incomers feeder As Per Mentioned Runs Of Cables In The Schematic Diagram.

Panel Switch Board Complete With All Internal Wiring, Name Plates And Complete In All Respects.

Note : GA drawings shall be got approved from Client(user)/ Architects / Consultants before fabrication.The panel has to be specifically fabricated as per the space available at site. The existing column positions will also be considered.

SUB HEAD-XXV : WATER COOLERS

Supply, Installation, testing & Commissioning of wall mounted/floor mounted type Stainless steel water coolers with specifications as mentioned below and as directed by the Engineer-In-Charge

Size - 564 x 705 x 1397mm

Weight not less than 67 kgs

Storage Capacity (ltrs) - 120

Cooling Capacity (ltrs/hr) - 80

Refrigerant - R134a

Current - 3.1 Amps

Type of Compressor - Hermatic type

SUB HEAD-XXVI : CRANES

Design review charges, inspection of cranes by Third Party Agency, Manufacturing, supply erection testing & commissioning of 25Ton capacity double girder EOT Crane with VVVF drive controls complete with long travel and cross travel movements including micro speeds for hoist, CT & LT operations as per IS 807/3177 and other relevant IS standards of the latest revision including Gantry Rail, shrouded Busbar, etc,complete

Span : 17 Mtrs, Lift : 7 Mtrs Bay Length : 50 Mtrs

SUB HEAD-XXVII : DG SETS

MV Control Cables

Supply, laying and commissioning of following size 1.1KV grade PVC insulated armoured Copper/ Aluminium conductor under ground cable, in built up cable trench/ already laid RCC hume pipe or on cable tray with all installation materials.

19C X 2.5 Sq.mm Copper

4C X 2.5 Sq.mm Copper

3C X 6 Sq.mm Copper

4C X 4 Sq.mm Copper

Providing Indoor End terminations for the cable specified under item above with compression type steel gland, lugs using crimping tool, Insulation tape, Identification tags etc. including end termination.

19C X 2.5 Sq.mm Copper

4C X 2.5 Sq.mm Copper

3C X 6 Sq.mm Copper

4C X 4 Sq.mm Copper

Supply, Transportation, erection and commissioning (Excluding Foundation) of 3 Phase, 415, 50Hz, water cooled multi cylinder diesel generator set with alternator of 320 KVA,contineous rating directly coupled Engine and Alternator with guard and mounted on a common base plate of Robust construction, Acoustic Enclosure as per CPCB norms , sound absorbing material, to restrict sound level up to 75 dB up to 1 mtr distance and as per CPCB norms etc as per following specifications mentioned below.

Alternator :The alternator of the output rating shall be 3 Phase, 415V, 50Hz, Ac , 0.8 P.F. lagging at 1500 RPM. The alternator is self excited, self regulated, and shall confirm to IS: 13364 of 1992 or latest version with regulation of +5% from no load to full load. degree of protections shall be IP23.

Diesel Engine :Diesel Engine start, developing suitable BHP output at 1500 RPM with mechanical / electronic governing so as to enable the alternator to give 320 KVA continuous output at 0.8 P.F. lagging at NTP conditions. The diesel engine shall be capable of providing 10% O/L for 1 Hr for every 11 Hrs of continuous running at full load. The engine with 1st filling of oil and Diesel etc. 01. Exhaust pipe of required size and length with insulation as per the site condition with alluminium clading. 02. Diesel tank suitable for 8 to 12 Hours

320 KVA, 3 Phase, 415, 50 Hz, not less than 380 BHP, water cooled multy cylinder diesel generator set with alternator of 320 KVA output continious rating at 0.8 p.f, Batteries.

Supply, Fixing, testing and Commissioning of 200 mm NB, MS, 4.85 mm thick plate, Exhaust pipe, Exhaust gas piping system of Class `B' MS pipe as per IS:3589 with welded joints, cut to required lengths with necessary bends, fittings, expansion joints of suitable diameter including providing hot dip galvanized supporting / clamping arrangements at suitable intervals, anti vibration mounting and 26 SWG aluminium sheet cladding complete as required.(Stack height should be in accordance with emission regulations of CPCB, which will go well above the top most terrace for 320 KVA Dgset Exhaust manifold upto Silencer )

Supply and installation of SS Flexible Bellows for 200 mm NB, MS, 4.85 mm thick plate, Exhaust pipe with counter flanges,heat resitant gaskets, nuts- bolts-washers etc,complete as required

Supply and installation of Aluminium cladding for 200 mm NB, MS, 4.85 mm thick plate, Exhaust pipe residencial silencers with Mineral Wool 50mm Thick, density 64 Kg/cu.mtr., wire mesh and 24 gauge aluminium cladding The aluminum foil should be tightly cladded to insulation surface of pipe. The aluminum cladding shall be lock with sheet metal screws with other sections of aluminium foil. The measurement shall be done longitudenally with any extra allownce for bends beyond centre line of bend..-For 320KVA DG SET

Supply and installation of MS Support structure of height 18 mtr will be duly coated with two coats of red-oxide primer and two coats of enamel paint. The colour shade of final paint will be as decided by the client. (Stack height should be in accordance with emission regulations of CPCB,combined structure for 2 DG set)

LT CABLES :

Supply,and transportation of following XLPE insulated, 1100V grade armoured aluminium/copper cable as per specification laid in trench/cable tray including cost and conveyance of all materials and accessories with labor charges etc.,

3.5C x 240 SQ.MM AL. AR. CABLE

LT CABLES TERMINATIONS :

Supplying and making end termination with brass compression gland and aluminium lugs for 3.5C x 240 SQ.MM AL. AR. CABLE size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.

Supply of CPRI tested maintenance free ,Low carbon mild steel copper coated earth rod of 3 metre electrode having diameter of 14.2 mm with copper coating thickness of 250micron tested as per IEC 62561-2 & is provided with universal clamp made of SS to connect rod with flat conductor. Earth conductivity enhancing compound shall be of 25 kg/pit tested as per IEC 62561-7,TCLP tested. The above arrangements shall be provided with Heavy duty earth champer of 5000kg load bearing capacity to ensure the safety of earthing system.

Providing and fixing earth bus of 50x6mm Hot Dip Galvanized GI strip

Providing and fixing 25 mm X 5 mm copper strip on surface or in recess for connections etc. as required.

SUB HEAD-XXVIII : IP CCTV SURVEILLANCE SYSTEM

Note: The IP CCTV system shall be suitable for indoor / outdoor application as per requirement with colour day/night cameras as specified. The system architecture shall perform full fledged remote viewing capability. The necessary connectors / accessories for video Input / Output shall be supplied by the supplier .

Supply, installation, Testing and commissioning of 1/3" colour motion based, IR Dome type IP POE cameras with resolution of minimum 02 Mega pixel or higher, Day & Night type and min illumination of 0.01 lux with Fixed lens suitable for covering distance of 15 – 20 mtrs for indoor application along with complete fixing accessories and required software and licenses for the cameras.

Supply, installation, Testing and commissioning of 1/3" colour motion based, IR Bullet type Camera with additional Weatherproof Housing, IP vandal proof POE cameras with Varifocal lens resolution of minimum 02 Mega pixel or higher, Day & Night type and min illumination of 0.001 lux with lens suitable for covering distance of 60-70 mtrs for outdoor application along with complete fixing accessories and required software and licenses for the cameras.

Supply and installation, Testing and commissionig of ¼ colour high speed MPEG4 compliant with 30 X PTZ adjustment IP camera with resolution ,min illumianance of .005 lux under day night application should be able to cover a distance of minimum 300 Mtrs along with software & license . It should have weather proof housing with IP66 certification shall be along with mounting brackets.

Supply, installation , testing and Commissioning of Joy-Stick Keyboard Controller for PTZ Cameras

Supply and installation testing and commissioning of 24 port L3 switch fully managed SNMP (simple network management protocol) 10/100/1000 with 04 port Fiber uplink SFP (Small form factor) gigabit switch suitable for above connectivity along with all required connectors and fixing accessories.

Supply and installation testing and commissioning of 24 port Power on Ethernet (POE) Managable Gigabit Switch, with Minimum 2 SFP & all 24 Port 10/ 100/1000 gigabit Port suitable for above cameras ,with 2 No's of Fiber optic modules, Pigtails, along with all required connectors, Adequate weatherproof Enclosures and fixing accessories.

Supply and installation testing and commissioning of 08 port Power on Ethernet (POE) Managable Gigabit Switch, with Minimum 2 SFP & all 24 Port 10/ 100/1000 gigabit Port suitable for above cameras ,with 2 No's of Fiber optic modules, Pigtails, along with all required connectors, Adequate weatherproof Enclosures and fixing accessories.

Supply, installation, testing and commissioning of Rack Mount type 64 Channel Embedded Hardware Based NVR's suitable for the above mentioned Cameras and support upto 12 megapixel High End cameras, HDMI & VGA interface, Minimum 2 No's Gigabit LAN ports for network connectivity, including Storage of 36 TB Surveillance HDD/ 8 Slots, Per slot 6TB HDD,withRAID 5 & HDD Failover Support, recording @ 8 frames per second minimum, motion capture, including all required connectors and fixing accessories in complete. Note: Sufficient Connecting cables, connectors and mounting accessories shall be included This shall be compatible to Mile stone or One view software considering software license for all the above cameras.

Supply, Installation, Testing and Commissioning of recording Server Class Machines for recording the events @15fps (H.264) of the cameras mentioned above cameras per server, with the following Min specifications in each machine.i7 with latest configuration, 8 GB RAM, with Hard Disk capacity for minimum 60 days storage , Integrated Controller Card,DVD ROM Drive, original Windows 10 Server, Original OS, back end, MS office, 21” LED display monitor & anti virus software, 100/1000Mbps network card,along with housing 12 U rack and complete accessories.

Supply installation, testing and commissioning of latest configuration PC with 22'' LED Display Monitor for monitoring purpose, with client software installed and other accessories in complete. The PC is expected to be with preloaded suitable software’s.

Supply, laying, testing and commissioning of 3core 1.5sq.mm, 650V grade FRLS PVC insulated copper conductor flexible cable through existing M/s conduit ( shall be on actuals )

Supply and installation of 3 mts tapered pole for mounting the bullet / PTZ type outdoor cameras in the Main gate Entry / Exit, and shall able to with stand for the wind velocity, it shall include all installation accessories as required. Necessary Civil work shall be included.

Supply, laying, testing and commissioning of CAT 6 cable laid in 20mm dia heavy gauge M/s conduit with all fixing accessories

Supply and Laying of 6 Core Single mode armoured Fibre optic cable & 1" HDPI Pipe with all required connectors, Pigtails and all accessories.

Supply and laying of Hume pipe of 50mm Gi Class 'C' for laying across the drive way.

Supply and installation of pole mount Polycarbonate housing & SS Mounting plate of suitable sized weather proof box pre-installed for housing the Media Convertor, Electrical safety kit, 2 x RJ45 connectors (10/100 Mbps), 2 x SFP connectors (100/1000 Mbps) for SFP fiber optic modules, Operating conditions of -40 to + 65 deg C, Pre installed Cable gaskets, DIN rails, Cable clamps, Power cover for MCB fuse, lightning Surge Protection, 12V DC power supply unit along with all fixing accessories.

Supply and installation of 12 port LIU, with all required accessories with Enclosures. Required fiber termination boxes along with required splicing activity and otheraccessories shall be in the vendor scope even if not indicated in the specification.

Supply and fixing of 25mm dia 1.6 mm thick MS conduit run on surface of wall/Ceiling/above false ceiling and all fixing accessories in complete. The conduit in walls shall be concealed by chasing and finishing back complete with required accessories.

Supply and laying of following MS 25 mm dia flexible conduit at above false ceiling for taking control cables including all accessories as required (Shall be on actuals)

Supply, Installation and commissioning of 12U RAck with complete with required accessories.

Supply, Installation and Commissioning of 50" Professional Monitor with 10mtrs HDMI Cable and other accessories

Supply, Installation and commissioning of 4U RAck with complete with required accessories.

Supplying and laying of 63 mm dia (OD-63 mm & ID-51 mm nominal) DWC pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc. in the existing trench, complete as required

SUB HEAD XXIX - ROADS , HARDSTANDING & DRAINS

Earth work in excavation by mechanical means (Hydraulic excavator) /manual means over areas (exceeding 30cm in depth. 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth, lead upto 50m and lift upto 1.5m, disposed earth to be levelled and neatly dressed.

All kinds of soil.

Earth work in Excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.

All kinds of soil.

Preparation and consolidation of sub grade with power road roller of 8 to 12 tonne capacity after excavating earth to an average of 22.5 cm depth, dressing to camber and consolidating with road roller including making good the undulations etc. and re-rolling the sub grade and disposal of surplus earth with lead upto 50 metres.

Preparation of Subgrade

Providing, laying, spreading and compacting graded stone aggregate (size range 53 mm to 0.075 mm ) to wet mix macadam (WMM) specification including premixing the material with water at OMC in for all leads & lifts, laying in uniform layers with mechanical paverfinisher in sub- base / base course on well prepared surface and compacting with vibratory roller of 8 to 10 tonne capacity to achievethe desired density, complete as per specifications and directions of Engineer-in-Charge.

Construction of dry lean cement concrete sub base over a prepared sub-grade with coarse and fine aggregate conforming to IS:383, the size of coarse aggregate not exceeding 25 mm, aggregate cement ratio not to exceed 15:1, aggregate gradation after blending to be as per specifications, cement content not to be less than 150 Kg/cum, optimum moisture content to be determined during trial length construction, concrete strength not to be less than 10 Mpa at 7 days, mixed in a batching plant, transported to site, for all leads & lifts, laid with a mechanical paver, compacting with 8-10 tonne vibratory roller, finishing and curing etc. complete as per direction of Engineerin-charge.

Providing and laying design mix cement concrete of M-30 grade, in roads/ taxi tracks/ runways, using cement content as per design mix, using coarse sand and graded stone aggregate of 20 mm nominal size in appropriate proportions as per approved & specified design criteria, providing dowel bars with sleeve/ tie bars wherever required,laying at site, spreading and compacting mechanically by using needle and surface vibrators, levelling to required slope/ camber,finishing with required texture, including steel form work with sturdy M.S. channel sections, curing, making provision for contraction/expansion, construction & longitudinal joints (10 mm wide x 50 mm deep)

by groove cutting machine, providing and filling joints with approved joint filler and sealants, complete all as per direction of Engineer-in-charge (Item of joint fillers, sealants, dowel bars with sleeve/ tie bars to be paid separately). Note:- Cement content considered in M-30 is @ 340 kg/cum. Excess/less cement used as per design mix is payable/ recoverableseparately.Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 1.10 times of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement.

(a) Cement concrete manufactured in automatic batching plant (RMC plant) i/c transportation to site in transit

Providing and laying design mix cement concrete of M-30 grade, in roads/ taxi tracks/ runways, using cement content as per design mix, using manufactured sand and graded stone aggregate of 20 mm nominal size in appropriate proportions as per approved & specified design criteria, providing dowel bars with sleeve/ tie bars wherever required,laying at site, spreading and compacting mechanically by using needle and surface vibrators, levelling to required slope/ camber,finishing with required texture, including steel form work with sturdy M.S. channel sections, curing, making provision for contraction/expansion, construction & longitudinal joints (10 mm wide x 50 mm deep)

by groove cutting machine, providing and filling joints with approved joint filler and sealants, complete all as per direction of Engineer-in-charge (Item of joint fillers, sealants, dowel bars with sleeve/ tie bars to be paid separately). Note:- Cement content considered in M-30 is @ 340 kg/cum. Excess/less cement used as per design mix is payable/ recoverableseparately.Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 1.10 times of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement.

(a) Cement concrete manufactured in automatic batching plant (RMC plant) i/c transportation to site in transit

Providing and fixing MS round dowel bars of specified dia and length at required spacing including providing and fixing part length covered with PVC sleeve and dowel caps filled with compressable material of 100 mm ong as per drawing along the joints including making necessary arrangements to keep the bars in position during pouring etc., complete as directed by Engineer in Charge. ( Note: PVC sleeves to be measured and paid separetely.)

38mm dia , 500mm long in Expanstion Joints,Transeverse constructions joints all as per drawing.

Providing and fixing PVC dowel sleeve with closely fitting cap of 100mm long in expansion joints

Providing and fixing Deformed Tie bars of specified dia and length at required spacing in Longitudinal Joints including providing part length painted with Bituminous paint of 150mm long including making necessary arrangements to keep the bars in position during pouring etc., complete as directed by Engineer in Charge.

12 mm dia, 640mm long at 600mm c/c in Longitudinal Joints.

Providing and fixing pre-moulded joint filler in expansion joints of RCC roads / CC pavements after making the joints dust free with high pressure air jet cleaners, all complete as per direction of the Engineer-in-Charge. (Pre-moulded joint fillers shall be made of bitumen hot sealing compound impregnated fibre board having impregnation more than 35%, conforming to IS:1838 for fibre board and IS: 1834 for hot sealing bitumen compound grade A.)

Providing and filling in expansion joint of groove size 20mm wide by filling with 25 mm deep polyurethane sealant of Colpor 200 or equilent of approved make over 2mm deep compressible debonding strip and 20mm wide compressible filler board as per drawing etc, including cost of primer in expansion joints.

Providing and filling in Transverse Construction Joints of groove size 8 mm wide x 19 mm deep filling with polyurethane sealant of Colpor 200 or equilent of approved make over 2mm deep compressible debonding strip and soft rope/back-up rod as per drawing etc, including cost of primer in construction joint.

Providing and filling in Longitudinal Joints of groove size 10 mm wide x 22 mm deep by filling with polyurethane sealant of Colpor 200 or equilent of approved make over 5mm deep compressible debonding strip and soft rope/back-up rod as per drawing etc, including cost of primer in dummy joint.

Add for using extra cement in the items of design mix over and above the specified cement content therein.

Supplying and laying 150 microns plastic sheets over DLC Concrete.

Providing and laying non- pressure NP2 class RCC pipes with collars joints with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc., complete for culverts, road crossings of electric cables, water supply pipe line and telephone cable etc.,

300 mm dia

450 mm dia

600 mm dia

900 mm dia

Providing and laying in position cement concrete of 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size) grade excluding the cost of centering and shuttering - All work up to plinth level.

Providing and laying cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) in, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor, etc. up to floor five level, excluding the cost of centering, shuttering and finishing.

15 mm cement plaster on rough side of single or half brick wall finished with a floating coat of neat cement of mix :

1:3 (1 cement: 3 fine sand)

Providing rain water harvesting pit of size 2meter dia and 2.5m depth the pit shall have 750mm of 40mm stone aggregate at bottom over which ther shall be 750mm of stone aggregate of 1000mm of course sand filling respectively brick work all round the periphery of the pit 300mm below ground and 150mm of above.

Providing and laying Bituminous concrete using crushed stone aggregates of specified grading, premixed with bituminous binder and filler, transporting the hot mix to work site by tippers, laying with paver finisher equiped with electronic sensor to the required grade,level and alignment and rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction and density as per specification, complete and as per directions of Engineer-in-Charge.

40/50 mm compacted thickness with bitumen of grade VG-30 @ 5.5% (percentage by weight of total mix) and lime filler @ 3% (percentage by weight of Aggregate) prepared in Batch Type Hot Mix Plant of 100-120 TPH capacity.

Providing and applying tack coat using bitumen emulsion conforming to IS:8887, using emulsion pressure distributer including preparing the surface & cleaning with mechanical broom.

With medium setting bitumen emulsion On W.B.M / W.M.M. @ 0.4kg/sqm

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundations upto plinth level in all shapes and sizes in :

Cement mortar 1:6 (1 cement : 6 coarse sand)

Supplying and filling of earth obtained from out side MoD land (including royalty) by mechanical transport upto a lead of 10 km and filling in layers not exceeding 20 cm in depth, breaking clods, watering, rolling each layer with ½ tonne roller, or wooden or steel rammers, and rolling every 3rd and top-most layer with power roller of minimum 8 tonnes and dressing up, in embankments for roads, flood banks, marginal banks, and guide banks etc., lead upto 50 m and lift upto 1.5 m : (5% shall be deducted for voids to arrive at the net quantity for payment)

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge (length of finished kerb edging shall be measured for payment). (Precast C.C. kerb stone shall be approved by Engineer-in-charge).

Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge.

(a) 60mm thick cement concrete paver block of M-35 grade with approved colour, design & pattern.

Providing and placing in position 100 mm thick factory made machine batched & machine mixed Precast RCC Rectangular Covers on drains of footpath of various sizes, of M-25 grade cement concrete for RCC work, including cost of centering, shuttering, reinforcement of 8 mm dia TMT bars of Fe 500 grade @ maximum 100mm c/c on both ways , neat cement punning on finished surface, properly encased on all edges with 1.6 mm thick , 100 mm wide MS sheet duly painted over priming coat , reinforcement to be welded at edges with MS sheet and providing 2 Nos. 12 mm dia bar for hooks etc i/c cost of cartage, all leads & lift, handling at site etc. all complete as per direction of Engineer-in-Charge.

Providing and fixing factory made precast RCC perforated drain covers, having concrete of strength not less than M-25, of size 1000 x 450x50 mm, reinforced with 8 mm dia four nos longitudinal & 9 nos cross sectional T.M.T. hoop bars, including providing 50 mm dia perforations @ 100 to 125 mm c/c, including providing edge binding with M.S. flats of size 50 mm x 1.6 mm complete, all as per direction of Engineer-in-charge.

SUB HEAD-XXX : TEST TRACKS

Supplying & laying of 4 mm thick Non- Woven Geotextile layer as per drawing.

Providing and applying tack coat using bitumen emulsion conforming to IS:8887, using emulsion pressure distributer including preparing the surface & cleaning with mechanical broom.

With rapid setting bitumen emulsion On W.B.M / W.M.M. @ 0.4kg/sqm

Providing and laying Bituminous concrete using crushed stone aggregates of specified grading, premixed with bituminous binder and filler, transporting the hot mix to work site by tippers, laying with paver finisher equiped with electronic sensor to the required grade, level and alignment and rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction and density as per specification, complete and as per directions of Engineer-in-Charge.

(a) 40/50 mm compacted thickness with bitumen of grade VG-30 @ 5.5% (percentage by weight of total mix) and lime filler @ 3% (percentage by weight of Aggregate) prepared in Batch Type Hot Mix Plant of 100-120 TPH capacity

Supplying and filling of earth obtained from with in MoD land by mechanical transport upto a lead of 5 km and filling in layers not exceeding 20 cm in depth, breaking clods, watering, rolling each layer with ½ tonne roller, or wooden or steel rammers, and rolling every 3rd and top-most layer with power roller of minimum 8 tonnes and dressing up, in embankments for roads, flood banks, marginal banks, and guide banks etc.complete, lead upto 50 m and lift upto 1.5 m : (5% shall be deducted for voids to arrive at the net quantity for payment)

Supplying and filling of earth obtained from out side MoD land by mechanical transport upto a lead of 5 km and filling in layers not exceeding 20 cm in depth, breaking clods, watering, rolling each layer with ½ tonne roller, or wooden or steel rammers, and rolling every 3rd and top-most layer with power roller of minimum 8 tonnes and dressing up, in embankments for roads, flood banks, marginal banks, and guide banks etc.complete, lead upto 50 m and lift upto 1.5 m : (5% shall be deducted for voids to arrive at the net quantity for payment)

Providing and laying moorum mixed with lime on subgrade having Plasticity Index less than 6 and CBR value not less than 8%, including compaction in layers not exceeding 20 cm ,rolling each layer with ½ tonne roller, or wooden or steel rammers, and rolling every 3rd and top-most layer with power roller of minimum 8 tonnes and dressing up, in embankments for roads, flood banks, marginal banks, and guide banks etc.complete all as per drawing and direction of Engineer-in-charge. (5% shall be deducted for voids to arrive at the net quantity for payment)

Extra for compaction of earth work in embankment under optimum moisture conditions to give at least 95% of the maximum dry density (proctor density).

Providing and laying Steel Fiber Reinforced Concrete (FRC) mixture having a characteristic flexural strength of 4.5 MPa as designed in accordance with IRC:SP:46-2013 and the construction of the wearing slab shall be in accordance with IRC:15-2017,the quality control during the construction should be as per IRC:15-2017,IRC:SP:112-2017 and MoRTH specifications.

Design mix of steel fiber Reinforced cement concrete of M-40 grade, in roads/ taxi tracks/ runways, using cement content as per design mix with portland cement (OPC-43 grade), using coarse sand and graded stone aggregate of 20 mm nominal size in appropriate proportions as per approved & specified design criteria, Providing Cold-drawn Steel fibers as per IRC:SP:46-2013 with hooked end and length of 60mm , aspect ratio of 80 and providing dowel bars with sleeve/ tie bars wherever required,laying at site, using an approved slip form paver having independant design units for spreading, consolidating finishing and compacting mechanically by using needle and surface vibrators, levelling to required slope/ camber,finishing with required texture, including steel form work with sturdy M.S. channel sections, curing, making provision for contraction/expansion,

construction & longitudinal joints (10 mm wide x 75 mm deep) by groove cutting machine, providing and filling joints with approved joint filler and sealants, complete all as per direction of Engineer-in-charge (Item of Steel fibers, joint fillers, sealants, dowel bars with sleeve/ tie bars to be paid separately). Note:- Cement content considered in M-40 is @ 390 kg/cum. Excess/less cement used as per design mix is payable/ recoverable separately.Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement.

(a) Cement concrete using coarse sand and graded stone aggregate of 20 mm nominal size ,manufactured in automatic batching plant (RMC plant) i/c transportation to site in transit mixer

(b) Cement concrete using manufactured sand (i.e.Robo sand) and graded stone aggregate of 20 mm nominal size, manufactured in automatic batching plant (RMC plant) i/c transportation to site in transit mixer

Supplying and laying /mixing of cold-drawn steel fibres of approved make with hooked ends having diameter 0.75mm, length of 60 mm and an aspect ratio of 80 for Steel Fibre reinforced Concrete Slabs/ CC Roads for Test Tracks. The dosage of fibres should be 32 kg/cum. The steel fibres having an equivalent flexural strength value at 3 mm deflection greater than 1.6 MPa. The specifications for the steel fibres shall be in accordance with IRC:SP:46-2013,MoRTH Standard Specifications etc.,complete.

Providing and fixing MS round dowel bars of specified dia and length at required spacing including providing and fixing part length covered with PVC sleeve and dowel caps filled with compressable material of 100 mm ong as per drawing along the joints including making necessary arrangements to keep the bars in position during pouring etc., complete as directed by Engineer in Charge. ( Note: PVC sleeves to be measured and paid separetely.)

38mm dia , 500mm long in Expanstion Joints,Transeverse constructions joints all as per drawing.

Providing and fixing PVC dowel sleeve with closely fitting cap of 100mm long in expansion joints

Providing and fixing Deformed Tie bars of specified dia and length at required spacing including providing part length covered 150mm length painted with Bituminus paint as per drawing, along the joints including making necessary arrangements to keep the bars in position during pouring etc., complete as directed by Engineer in Charge.

12mm dia, 640 mm long in Longitudinal Joints as per drawing.

Providing and filling in expansion joint of groove size 20mm wide by filling with 25 mm deep polyurethane sealant of Colpor 200 or equilent of approved make over 2mm deep compressible debonding strip and 20mm wide compressible filler board as per drawing etc, including cost of primer in expansion joints.

Providing and filling in Transverse Construction Joints of groove size 8 mm wide x 19 mm deep filling with polyurethane sealant of Colpor 200 or equilent of approved make over 2mm deep compressible debonding strip and soft rope/back-up rod as per drawing etc, including cost of primer in construction joint.

Providing and filling in Longitudinal Joints of groove size 10 mm wide x 22 mm deep by filling with polyurethane sealant of Colpor 200 or equilent of approved make over 5mm deep compressible debonding strip and soft rope/back-up rod as per drawing etc, including cost of primer in dummy joint.

Add for using extra cement in the items of design mix over and above the specified cement content therein.

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level

(a) Thermo-Mechanically Treated bars of grade Fe-500D or more

Providing and fixing pre-moulded joint filler in expansion joints of RCC roads / CC pavements after making the joints dust free with high pressure air jet cleaners, all complete as per direction of the Engineer-in-Charge. (Pre-moulded joint fillers shall be made of bitumen hot sealing compound impregnated fibre board having impregnation more than 35%, conforming to IS:1838 for fibre board and IS: 1834 for hot sealing bitumen compound grade A.)

Providing and fixing pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion,Providing and fixing unplasticised Rigid pipes of following dia

(a) 40 mm dia in Expanstion joints and Transverse construction joints.

(b) 110 mm dia for weep holes

Preparation and consolidation of sub grade with power road roller of 8 to 12 tonne capacity after excavating earth to an average of 22.5 cm depth, dressing to camber and consolidating with road roller including making good the undulations etc. and re-rolling the sub grade and disposal of surplus earthwith lead upto 50 metres.

Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge.

(a) All kinds of soil

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.

(a) All kinds of soil

Construction of granular sub-base by providing close graded Material conforming to specifications, mixing in a mechanical mix plant at OMC, carriage of mixed material by tippers to work site, for all leads & lifts, spreading in uniform layers of specified thickness with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per specifications and directions of Engineer-in-Charge. a) With material conforming to Grade-I (size range 75 mm to 0.075 mm) having CBR Value-30( Construction shall be in accordence with section 400 of Morth specifications/IRC:15-2017 guidelines).

Construction of dry lean cement concrete sub base over a prepared sub-grade with coarse and fine aggregate conforming to IS:383, the size of coarse aggregate not exceeding 25 mm, aggregate cement ratio not to exceed 15:1, aggregate gradation after blending to be as per specifications, cement content not to be less than 150 Kg/cum, optimum moisture content to be determined during trial length construction, concrete strength not to be less than 10 Mpa at 7 days, mixed in a batching plant, transported to site, for all leads & lifts, laid with a mechanical paver, compacting with 8-10 tonne vibratory roller, finishing and curing etc. complete as per direction of Engineerin-charge.(Dry lean conrete conforming to IRC:SP:49 and section 600 of MoRTH specifications.)

Supplying and laying 150 microns thick plastic sheets below RCC

Supplying and laying/fixing granite stone boulders of 15 cm to 20 cm cm thick at site and fixing the stone laid in courses and required profile with hammer dressed stones having no side less than 15 cm, with minimum depth of 20 cm including cost of cement morter of 1:4 and preparing the bedding surface etc. all complete.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :

1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources)

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate(i.e. Coarse sand) derived from natural sources, Ordinary Portland cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement. All works upto plinth level (a) Concrete of M25 grade with minimum cement content of 330 kg /cum.

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and manufactured sand (i.e. Robo sand), Ordinary Portland cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement. All works upto plinth level (a) Concrete of M25 grade with minimum cement content of 330 kg /cum.

Centering and shuttering including strutting, propping etc. and removal of form for

(a) Foundations, footings, bases of columns, etc. for mass concrete.

(b) Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

Providing and laying in position ready mixed or site batched design mix cement concrete for plain cement concrete work; using coarse aggregate and fine aggregate derived from natural sources(i.e. Coarse sand),Ordinary Portland cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard settingof concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering and finishing as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the minimum specified cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement. All works upto plinth level : Concrete of M10 grade with minimum cement content of 220 kg /cum

Providing and laying in position ready mixed or site batched design mix cement concrete for plain cement concrete work; using coarse aggregate and manufactured sand (i.e. ROBO sand), Ordinary Portland cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard settingof concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering and finishing as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the minimum specified cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement. All works upto plinth level : Concrete of M10 grade with minimum cement content of 220 kg /cum

Dismantling stone work of Road work manually/ by mechanical means including stacking of serviceable and disposal of unserviceable material within 2 km lead as per direction of Engineer-in-charge :

In cement mortar

Supplying and filling gravel with clay in clay and mud soil bin, including watering, ramming, consolidating and dressing complete.(10% shall be deducted for voids to arrive at the net quantity for payment)

Supplying and filling in plinth with sand in sand course, including watering,ramming, consolidating and dressing complete.

Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

62 mm thick cement concrete flooring with concrete hardener topping, under layer 50 mm thick cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) and top layer 12mm thick cement hardener consisting of mix 1:2 (1 cement hardener mix : 2 graded stone aggregate, 6mm nominal size) by volume, hardening compound mixed @ 2 litre per 50 kg of cement or as per manufacture’s specifications. This includes cost of cement slurry, but excluding the cost of nosing of steps etc. complete

Supplying and filling with gravel, including watering, ramming, consolidating and dressing complete. filling in layers not exceeding 20 cm in depth, breaking clods, watering, rolling each layer with ½ tonne roller, or wooden or steel rammers, and rolling every 3rd and top-most layer with power roller of minimum 8 tonnes and dressing up, in embankments for roads, flood banks, marginal banks, and guide banks etc., lead upto 50 m and lift upto 1.5 m (5% shall be deducted for voids to arrive at the net quantity for payment)

Providing and supply of Polysulphide sealant of approved make for 10mmx20mm groove in existing cracks as per the requirements

Supplying and fixing 10 Gauge weld mesh of size 100mm x100 mm for floor/roof slab concrete screed over the micro beams as reinforcement. The weld mesh shall be fixed as per drawing.

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. External work

(a) 32 mm dia nominal bore

(a) 80 mm dia nominal bore

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :

(a) 80 mm nominal bore

Supplying &fixing Nozzles of 25 mm dia

Providing, laying, spreading and compacting graded stone aggregate (size range 53 mm to 0.075 mm ) to wet mix macadam (WMM) specification including premixing the material with water at OMC in for all leads & lifts, laying in uniform layers with mechanical paverfinisher in sub- base / base course on well prepared surface and compacting with vibratory roller of 8 to 10 tonne capacity to achievethe desired density, complete as per specifications and directions of Engineer-in-Charge.

Providing and laying in position ready mixed or site batched design mix cement concrete for plain cement concrete work; using coarse aggregate and fine aggregate derived from natural sources( Coarse sand), Ordinary Portland cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard settingof concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering and finishing as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the minimum specified cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement. All works upto plinth level : Concrete of M15 grade with minimum cement content of 240 kg /cum

Providing and laying in position ready mixed or site batched design mix cement concrete for plain cement concrete work; using coarse aggregate and manufactured sand (Robo sand), Ordinary Portland cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard settingof concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering and finishing as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the minimum specified cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement. All works upto plinth level : Concrete of M15 grade with minimum cement content of 240 kg /cum

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : Two or more coats on new work including primer With ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanised iron/ steel works.

Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : (a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours. (b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours.The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry.

SUB HEAD-XXXI : EXTERNAL WATER SUPPLY

Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/ bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer-in-charge, upto 90 metre depth below ground level.

All types of soil

350 mm dia

Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge.

200 mm nominal size dia

Gravel packing in tubewell construction in accordance with IS: 4097, including providing gravel fine/ medium/ coarse, in required grading & sizes as per actual requirement, all complete as per direction of Engineer-in-charge.

TUBE WELL

Development of tube well in accordance with IS : 2800 (part I) and IS: 11189, to establish maximum rate of usable water yield without sand content (beyond permissible limit), with required capacity air compressor, running the compressor for required time till well is fully developed, measuring yield of well by “V” notch method or any other approved method, measuring static level & draw down etc. by step draw down method, collecting water samples & getting tested in approved laboratory, i/c disinfection of tubewell, all complete, including hire & labour charges of air compressor, tools & accessories etc., all as per requirement and direction of Engineer-in-charge.

Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for borewell of:

200 mm dia

Providing and fixing M.S. clamp of required dia to the top of casing/ housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts of required size complete.

200 mm clamp

Providing and fixing Bail plug/ Bottom plug of required dia to the bottom of pipe assembly of tubewell as per IS:2800 (part I).

200 mm dia

Submersible pumps and motor including suitable control panel all accessories with fittings & fixing & commissioning etc. Supply and installation of submersible pump set for 1 No. of bore well (capacity 3000 GPH) head 60m to 120m depending on yield HP commensurating to capacity & head) as per instruction of the EIC

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc.

40 mm dia nominal bore

50 mm dia nominal bore

65 mm dia nominal bore

80 mm dia nominal bore

Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete :

50 to 80 mm nominal bore

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :

40 mm dia nominal bore

50 mm dia nominal bore

65 mm dia nominal bore

80 mm dia nominal bore

Providing and fixing gun metal non- return valve of approved quality (screwed end) :

80mm nominal bore

Horizontal

Suction / Delivery - 65 /50mm

Range - Head 24m , Discharge - 3.10 lps

Motor rating - 2.0 HP

Constructing masonry Chamber 60x60x75 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I. surface box 100mm top diameter, 160 mm bottom diameter and 180 mm deep ( inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size ) , i/c necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design : With common burnt clay F.P.S.(non modular) bricks of class designation 7.5

PVC flat cable with fitting suitably for commissioning, supply and installation of 1x3 copper based 6 sqm flat cable required for 1 nos. pump set as per instruction of EIC.

SUB HEAD XXXII : SEWAGE DISPOSAL SYSTEM

Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m :

All kinds of soil

Pipes, cables etc. exceeding 80 mm dia. But not exceeding 300 mm dia

Earth work in excavation by mechanical means (Hydraulic excavator) /manual means over areas (exceeding 30cm in depth. 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth, lead upto 50m and lift upto 1.5m, disposed earth to be levelled and neatly dressed.

All kinds of soil.

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m. (10% shall be deducted for voids to arrive at the net quantity for payment)

Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete :

100 mm diameter

150mm diametre

Providing and laying S.W pipe including cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) all-round S.W. pipes including bed concrete as per standard design:

100 mm diametre S.W. pipe

150 mm diametre S.W. pipe

Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand (zone- III) : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design :

Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Extra for depth for manholes :

Of Size 90x80 cm With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Providing and placing in position Ready made septic tanks of Sintex or approved equivalent make , of capacities as mentioned below, made of combination of Polyethylene (LLDPE) material, which shall be 100% eco friendly and rust / corrosion / leak proof and not prone to cracking. The tank shall be completely water & air tight. The tank shall be provided with 110mm dia PE inlet and outlet pipes. Baffle wall shall be provided made of 3mm thick PE sheet. Suitable number of plastic media (PE pall rings) , surface area of media being not less than 190sqm / cum shall be filled in the tank. Tank shall be covered with 400mm dia manhole cover and provided with 50mm dia air vent pipe etc all complete to the satisfaction of Engineer-in-Charge.

15 Users Septic tank (3000 litres) made of 9.5mm thick LLDPE sheet weighing not less than 120 kg

30 Users Septic tank (5000 litres) made of 11.1mm thick LLDPE sheet weighing not less than 190 kg

Making soak pit 2.5 diameter 3.0 meter deep with 45 x 45 CM dry brick honey comb shaft with bricks of class designation 75 and S.W drain pipe 100mm diameter 1.8 m long complete as per standerd design

Providing and fixing of PVC rungs suitable for fixing to UG sump / OH tank and similar locations of size 265mm length x 175mm wide x 25mm thick, reinforced inside with 10mm steel rod. The rungs shall be fixed with cement mortar and they shall be capable of withstanding 200 kg load under properly fixed condition, etc., all complete for finished item of work.

Design, Supply, erection and Commissioning of packaged sewage treatment plant of capacity 50m3 per day of Ion Exchange / Thermax or approved equivalent brand , suitable for installing in basements where clear height available under the beam shall be 3.5m.The STP shall consist of bar screen chamber, oil and grease trap chamber equilisation tank,biocask, FAB Feed pumps including Motors, Air blowers including motors, FAB reactors, Tube settlers, Sludge holding tank, Chlorine dosing system, V Notch plate, Filter feed pumps, Activated Carbon filter, centrifuge system, gear box, motor, MCC panel, any other equipment as required for tertiary system of treatment including supply, erection and testing of inter connecting pipe works, cabling, earthing with cable tray etc., all complete for finished item of work to the satisfaction of Engineer-in-Charge (Civil works will be measured separately)

NOTE: 1. The free trial runoff period for the STP shall be one month or till stabilization of STP units to provide desired treatment efficiencies which ever is later. , 2. The treatment shall be to the standards of tertiary treatment satisfying the following outlet parameters, BOD < 5 mg /l , COD < 30 mg/l, total suspended solids < 5 mg/l, PH value 6.5 - 8.0, oil and grease < 10 mg/l, temperature 25 - 30 degree centigrade. Only the following civil works shall be paid separately -

1) Bar screen pit 2) Oil & grease trap chamber 3) Equilisation tank 4) Chlorine contact tank 5) Filter feed tank 6) Treated water tank 7) Int. Sludge sump 8) Sludge holding tank 9) Drain Sump 10) Platforms for dosing tank and foundations for equipment.

The items listed below shall be under the scope of supply i) Bar Screen (2 Nos) - Suitable for 50 KLD FAB, ii) Air grid for equalisation tank (1 Lot) - Suitable for 50 KLD FAB, iii) FAB feed pumps (2 Nos- 1 W+ 1 S) - Suitable for 50 KLD FAB, iv) Motors for FAB feed pumps (2 Nos- 1 W+ 1 S)- Suitable for 50 KLD FAB, v) Air Blowers (2 Nos- 1 W+ 1 S) - Suitable for 50 KLD FAB, vi) Motors for Air Blowers (2 Nos- 1 W+ 1 S) - Suitable for 50 KLD FAB, vii) Biocask media - 1 Lot - Suitable for 50 KLD FAB, viii) Biocask - Air distribution grid - 1 Lot - Suitable for 50 KLD FAB, ix) Biocask reactor - 1 No.- Suitable for 50 KLD FAB, x) Tube settler media (1 Lot) - Suitable for 50 KLD FAB, xi) Collection Trough (1 Lot) - Suitable for 50 KLD FAB, xii) Air grid for sludge holding tank (1 Lot) - Suitable for 50 KLD FAB, xiii) Hypo dosing system (1 No) - Suitable for 50 KLD FAB

xiv) PAC dosing System (1 No) - Suitable for 50 KLD FAB, xv) PE dosing System (1 No) - Suitable for 50 KLD FAB, xvi) Filter feed pumps (2 Nos (1W+1S)) - Suitable for 50 KLD FAB, xvii) Dual media filter (1 No) - Suitable for 50 KLD FAB, xviii) Activated carbon filter (1 no) - Suitable for 50 KLD FAB, xix) Inter connecting piping and valves for air line (1 Lot) - Suitable for 50 KLD FAB, xx) Inter connecting piping and valves for sewage line (1 Lot) - Suitable for 50 KLD FAB, xxi) Instruments (1 Lot) - Suitable for 50 KLD FAB, xxii) Distribution board (1 no) - Suitable for 50 KLD FAB, xxiii) Electricals (1 Lot) - Suitable for 50 KLD FAB, xxiv) Centrifuge system (1 Lot) - Suitable for 50 KLD FAB, xxv) Pressure gauges (1 Lot), xxvi) Air Rotameter (1 No), xxvii) Level switches (1 Lot)

SUB HEAD XXXIII : SECURITY WALL & MS GATES

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50m.

All kinds of soil

Providing and laying in position cement concrete of 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size) grade excluding the cost of centering and shuttering - All work up to plinth level.

Random Rubble Masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) upto plinth level with :

Cement mortar 1:6 (1 cement : 6 coarse sand).

Random rubble masonry with hard stone in superstructure above plinth level and upto floor five level, including leveling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) at window sills, ceiling level and the like

Cement mortar 1:6 (1 cement : 6 coarse sand).

Providing and laying cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) in, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor, etc. up to floor five level, excluding the cost of centering, shuttering and finishing.

Centering and Shuttering including strutting, propping etc. and removal of form for :

Foundations, footings, bases of columns, etc. for mass concrete.

Pointing on stone work with cement mortar 1:3 (1 cement : 3 fine sand) :

Flush/ Ruled pointing

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.

In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works

Providing and applying Two coats of synthetic enamel paint of approved brand and shade over a coat of primer including preparation of surface and applying approved brand putty on following surfaces at all levels and locations etc., complete.

Steel surfaces with zinc chromate primer.

Providing and applying Two coats of Epoxy paint of approved brand and shade over a coat of primer including preparation of surface and applying approved brand putty on following surfaces at all levels and locations etc., complete.

On Steel surfaces .

Finishing walls with textured exterior paint of required shade : New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @ 2.20kg/10 sqm with Finishing walls with water proofing cement paint of required shade : New work (Two or more coats applied @ 3.84 kg/10 sqm)

Fencing with R.C.C. post placed at required distance, embedded in cement concrete blocks, every 15th post, last but one end post and corner post shall be strutted on both sides and end post one side only, provided with horizontal lines and two diagonals of barbed wire weighing 9.38 kg per 100 metres (minimum), between the two posts fitted and fixed with G.I. staples on wooden plugs or G.I. binding wire tied to 6 mm bar nibs fixed while casting the post (cost of R.C.C. posts, struts, earth work and concrete to be paid for separately) :-

Payment to be made per metre cost of total length of barbed wire used.

With G.I. barbed wire

Providing and fixing concertina coil fencing with punched tape concertina coil 600 mm dia 10 metre openable length ( total length 90 m), having 50 nos rounds per 6 metre length, upto 3 m height of wall with existing angle iron 'Y' shaped placed 2.4m or 3.00 m apart and with 9 horizontal R.B.T. reinforced barbed wire, stud tied with G.I. staples and G.I. clips to retain horizontal, including necessary bolts or G.I. barbed wire tied to angle iron, all complete as per direction of Engineer-in-charge, with reinforced barbed tape(R.B.T.) / Spring core (2.5mm thick) wire of high tensile strength of 165 kg/ sq.mm with tape (0.52 mm thick) and weight 43.478 gm/ metre (cost of M.S. angle, C.C. blocks shall be paid separately)

Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for Reinforced Cement Concrete Work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge. (Note :-cement content considered in this item is @ 330 kg/cum. Excess/less cement used as per design mix is payable/recoverable separately).

All works upto plinth level.

All works above plinth level upto floor V level.

Supplying fabricating and fixing in position Reinforcement Steel for RCC work at all levels and locations including the cost of steel, straightening, cutting,bending,binding and placing in position etc.,as per drawings and specifications including the cost of binding wire labour etc., complete for reinforced concrete. .

Thermo-Mechanically Treated bars of grade Fe-500D or more.

Centering and Shuttering including strutting, propping etc. and removal of form for :

Foundations, footings, bases of columns, etc. for mass concrete.

Lintels, beams, plinth beams, girders, bressumers and cantilevers.

Columns, Pillars, Piers, Abutments, Posts and Struts.

SUB HEAD XXXIV : AREA DEVELOPMENT

Supplying and filling of earth obtained from out side MoD land (including royalty) by mechanical transport upto a lead of 10 km and filling in layers not exceeding 20 cm in depth, breaking clods, watering, rolling each layer with ½ tonne roller, or wooden or steel rammers, and rolling every 3rd and top-most layer with power roller of minimum 8 tonnes and dressing up, in embankments for roads, flood banks, marginal banks, and guide banks etc., lead upto 50 m and lift upto 1.5 m :(5% shall be deducted for voids to arrive at the net quantity for payment)

SUBHEAD XXXV : EXTERNAL POWER SUPPLY

HT Cables

Supply, testing and commissioning of following size 11KV XLPE insulated armoured aluminium conductor under ground cable.The cable shall conform to IS 7098/ Part II.

3C X 300 sq.mm, 11KV, (UE)

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 11 kV grade of following size direct in ground including excavation, sand cushioning,protective covering and refilling the trench etc. as required.

Above 120 sq. mm and upto 400 sq. mm

Laying of one number PVC insulated and PVC sheathed/ XLPE power cable of 11 kV grade of following size in the existing RCC/ HUMEI METAL pipe as required.

Above 120 sq. mm and upto 400 sq. mm

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 11 kVgrade of following size in the existing masonry open duct as required.

Above 120 sq. mm and upto 400 sq. mm

Providing Indoor Heat shrinkable end terminations for the cable specified above with all materials, Bi-metallic lugs using crimping tool, 11KV Insulation tape, Identification tags etc., including end termination and Earthing of Gland.

3C X 300 sq.mm, 11KV(UE), Indoor

MV Cables

Supply, testing and commissioning of following size 1.1KV grade XLPE insulated armoured aluminium conductor cable.The cable shall conform to IS 7098/ Part I.

3.5C X 300 Sq.mm

3.5C X 240 Sq.mm

3.5C X 185 Sq.mm

3.5C X 120 Sq.mm

3.5C X 95 Sq.mm

3.5C X 70 Sq.mm

3.5C X 50 Sq.mm

3.5C X 35 Sq.mm

3.5C X 25 Sq.mm

4C X 16Sq.mm

4C X 10Sq.mm

4C x 6 SQ.MM CU. FLX. CABLE

3C x 16 SQ.MM CU.Flx. CABLE

Laying of one number PVC insulated and PVC sheathed I XLPE power cable of 1.1 kV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc. as required.

Up to 35Sq.mm

Above 35 sq. mm and upto 95 sq. mm

Above 95 sq. mm and upto 185 sq. mm

Above 185 sq. mm and upto 400 sq. mm

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 kV grade of following size in the existing RCC/ HUMEI METAL pipe as required.

Upto 35 sq. mm

Above 35 sq. mm and upto 95 sq. mm

Above 95 sq. mm and upto 185 sq. mm

Above 185 sq. mm and upto 400 sq. mm

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on cable tray as required.

Upto 35 sq. mm

Above 35 sq. mm and upto 95 sq. mm

Above 95 sq. mm and upto 185 sq. mm

Above 185 sq. mm and upto 400 sq. mm

Supplying and fixing cable route marker with 10 cm X 10 cm X 5 mm thick G.l. plate with inscription there on, bolted /welded to 35 mm X 35 mm X 6 mm angle iron, 60 cm long and fixing the same in ground as required.

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 kV grade as required.

3.5C X300 Sq.mm

3.5C X240 Sq.mm

3.5C X185 Sq.mm

3.5C X120 Sq.mm

3.5C X 95 Sq.mm

3.5C X 70 Sq.mm

3.5C X 50 Sq.mm

3.5C X 35 Sq.mm

3.5C X 25 Sq.mm

4C X 16Sq.mm

4C X 10Sq.mm

4C x 10 SQ.MM CU. FLX. CABLE

4C x 6 SQ.MM CU. FLX. CABLE

3C x 16 SQ.MM CU.Flx. CABLE

Control Cables

Supply, laying and commissioning of following size 1.1KV grade PVC insulated armoured copper conductor under ground cable, in built up cable trench/ already laid RCC hume pipe or on cable tray with all installation materials. The cable shall conform to IS 1554/Part I

4core 2.5sq.mm

6core 2.5sq.mm

3core 2.5sq.mm

19core 2.5sq.mm

3core 6sq.mm

Providing Double compression end terminations for the cable specified above with compression type gland, lugs using crimping tool, Insulation tape, Identification tags etc.,including end termination and Earthing of Gland.

4core 2.5sq.mm

6core 2.5sq.mm

3core 2.5sq.mm

19core 2.5sq.mm

3core 6sq.mm

SUBSTATION ACCESSORIES

Supply and laying of 2.5mm thick 11KV grade Rubber Mats as per IS 15652 of size 1000mm x 2000mm.

Supply and erecting 4.5KG Carbon Dioxide (CO2) Fire Extiguisher with necessary clamps made from 50 x 6mm M.S. Flat with Nut & Bolts growted in wall complete.

Supply and fixing of 4nos 9Ltrs Fire buckets round bottom type enamelpainted, white inside & Red out side with FIRE mark, filled with dry sand and Supply and erecting floor mounting stand for keeping four nos. of FIRE buckets comprising 1500mm in length, 900mm height frame made out of 30mm x 30mmx 4mm angle iron with cross supports for legs, welded with 4 hooks and duly painted with one coat of red lead and two coats of approved enamelled silver paint.

Providing printed instruction chart both in English, Hindi and local launguage and duly framed with front glasses, for treatment of person suffering from Electric shock.

Supply and Fixing of Laminated SLD-A1size

Providing pair of rubber hand gloves suitable for working on 11 KV

Supply and fixing of Danger Notice boards (in 3languages including local)

Supply, Installation, Testing and commissioning of Indoor type floor mounted metal clad VCB panel with 4 Nos VCBs, totally enclosed and fully inter locked horizontal draw out , horizontal isolated type breaker as per IS 13118 Specifications and as amended up to date and additional specifications, having capacities mentioned below, single break, trip free mechanism, motorised operated spring / manually charged and auto/manually closed breaker suitable for use on 11KV, 3 Phase, 50 HZ AC supply with short circuit fault level of 350 /500 MVA, complete with self-contained, fully inter locked rack in and rack out mechanism, air insulated but encapsulated copper bus bars of 630A capacity, breaker featured with mechanical ON/OFF indicator with hand trip device, spring charging motor, 110V DC closing and tripping coil, safety shutter assembly, shunt trip coil and auxiliary switch of 4 NO + 4 NC and equipped with the following switchgears and accessories including connections suitable for XLPE 11 KV cable, cable entry from bottom, end termination with heat shrinkable jointing material etc as required including construction of suitable CC works for VCB's etc complete.

INCOMER - 1 No

Vacuum circuit breaker electrical draw out type TP 11 KV 630 A not less than 26.3KA rated short circuit rating current -1No

POTENTIAL TRANSFORMER:1 No. 11000/110 Volts PT, Class 1 accuracy, 100 VA burden with HT/LT fuses.

CURRENT TRANSFORMER: 3 Nos epoxy resin cast CTs of ratio 75-150/5A, 15VA burden and accuracy class 1 for metering and class 5P10 for protection

METERING

1No Digital Multifunction meter with RS 485

Heater ON/OFF switch with space heater and thermostat, single phase switch with socket cubical lamp for panel illumination with door limit switch ,MCB's for AC & DC control.

LED indication lamps for breaker on, breaker off, spring charge indication, trip circuit healthy with push button, Auto trip indication meter, Auxiliary contact for service test position (4No +4 NC) service and test positions and R/Y/B indication lamps.

PROTECTION: 1 Nos. Microprocessor based IDMTL 3 over current and 1 earth fault relay with Over current, earth fault and short circuit protection.

High speed tripping relay

ANNUNCIATION: 8 Window annunciation panel with push buttons and hooters.

POWER PACK: Supply, Installation, testing and commissioning of Power pack with 230V input and 110V DC continuous output suitable for closing / tripping / indication of 3 Nos VCBs with 2.5sq.mm FRLS copper cable etc as required.

OUTGOINGS - 3 Nos

630A VCBs Electrical draw out type TP 11 KV 630 A not less than 26.3 KA rated short circuit rating current.

Each breaker shall consist the following.

CURRENT TRANSFORMER: Epoxy resin cast CTs of ratio 75-150-/5A, 15VA burden and accuracy class 1.0 for metering and class 5P10 for protection - 3 Nos

Digital Multifunction meter - 1 No with RS 485

PROTECTION : Microprocessor based IDMTL 3 over current and 1 earth fault relay with Over current, earth fault and short circuit protection - 1 No

High speed tripping relay

Auxiliary relay for bucholz A/T,OTI A/T, WTI A/T

Heater ON/OFF switch with space heater and thermostat, single phase switch with socket cubical lamp for panel illumination with door limit switch ,MCB's for AC & DC control.

INDICATION LAMPS: LED indication lamps for breaker on, breaker off, spring charge indication, trip circuit healthy with push button, Auto trip indication meter, Auxiliary contact for

11/0.433KV Transformers

Supply, Transportation, Installation, Testing and Commissioning of 3 Phase, 50 Hz, Dry type, Indoor type copper wound Transformer designed and manufactured as per IS 2026-1977 and IS 11171-1985, connected delta on primary side and Star on secondary side with additional neutral brought out on load side, 11000V / (433V / 415V) with HV off load tap changing + 5% to -5% in steps of 2.5%, temperature rise by the resistance 90⁰C complete with test reports with the following standard mountings.

Rated KVA : 315 KVA (Cast Resin),Service: Indoor , Mounting : Floor, Copper wound : Double, Type of cooling : ANAN, Insulation Class : Class F, Temperature rise by resistance : 90⁰C,Vector Group: Dyn 11,Primary Connection : Delta, Primary Volts : 11000, Primary Frequency : 50,Primary Phases : 3, Primary wires: 3, Secondary connection : Star, Secondary Volts : 433V / 415V, Secondary phases : 3, Secondary wires: 4, Taps on primary winding for primary voltage variation :+5.0% to - 10.0% in steps of 2.5% through links, Terminal arrangement, a. HV: Cable end box b. LV : Cable end box, No load losses (Watts): As per IS specifications, Load losses (Watts): As per IS specifications, Impedance(Z%) : As per IS specifications,. Fittings & Accessories, a. Rating and terminal marking plate b. Earthing terminals ,c. Lifting Lugs, d. Winding temperature Indicator ,e. Separate neutral bushing, f. Uni directional flat rollers.

MV PANELS

Design, fabrication, supply, installation, testing and commissioning of Indoor type LT Panels fabricated out of 14 gauge CRCA Sheet Steel in cubicle compartmentised free standing floor mounted, dust and vermin proof with reinforcement of suitable size angle iron, channel `T’ section and / or flats wherever necessary, 3 mm thick cable gland plates shall be provided on top as well as at the bottom of the panels. Panels shall be treated with all anticorrosive process before powder coating as per specification and final approved shade. 2 Nos. earthing terminals shall be provided for all panels. Panels shall be suitable for 415 V, 3 phase, 4 wire, 50 Hz supply system with IP52 Protection. Lifting hooks shall also be provided in all panels. Approval shall be taken for each panel in the form of shop drawings/GA drawings before fabrication. Galvanized hardware with zinc passivation shall be used in fabrication of panels.

Note:-a) ACB in the LT panel shall be Electrically operated drawout type . Air Circuit breaker of approved make suitable for 415V 3 Ph & N supply with microprocessor based tripping device comprising of overload, short circuit and instantaneous ground fault protection including suitable range CTs and separate LED indications for overload, short circuit and ground fault along with release and also micro switches for service, isolated and locking positions for the breaker, door interlock, secondary isolating contacts, auxiliary contacts as required including ON/OFF indications, trip push button, trip indication, front operating handle and other connected accessories complete in all respects. b) All ACB's should be rated for minimum 50KA breaking capacity as detailed in BOQ (Icu=Ics=Icw for 1sec)

The operating height of the Panel shall not exceed 2.1 mtr. from FFL.

Aluminium bus bar size for carriying out specified current shall be as per type test certificate.

All MCCBs in the LT panel shall be adjustable with thermal settings(80% to 100%), overload and short circuit releases including door interlocking device, front operating handle complete,ON and OFF indication of LED module etc. complete in all respects.

MAIN PCC 1

630A ACB Incomers From Transformer-1 & DG-1

630A 50kA FP ACB Microprocessor release Motor wound spring charged closing mechanism (EDO),horizontal drawout type with over current,short circuit & earth fault protection release, screen display of measurements like Current : phase/ neutral/ earth, average, max,%loading, seq components, Voltage : Phase, Line, Average and with RS-485 Port - 1 Nos

Under Voltage relay / release with timer. - 1 Nos

TNC switch. - 1 Nos

3 CT's of ratio 630/5A, Class 1 accuracy 15 VA burden for metering. - 1 Set

3 CT's of ratio 630/5A, Class 5P10, accuracy 15 VA burden for PROTECTION . - 1 Set

Power Quality Meter (digital type) consisting of I, V, kW, kWH, kVA, PF, HZ, MDI,Capability of Disturbance Direction Detection,Sag & Swell Monitoring with Waveform Capturing Harmonics analysis upto 63rd order for Voltage & Current,(PM8000 series or equivalent) with Ethernet communication port. - 1 Nos

Restricted earth fault relay with PS class CT’s- 1 Set

LED type phase indicating lamps, each lamp shall be with backup MCB along with hooter, auxillary relay, 2 sets of push buttons.

LED type indicating lamp for indicating the status of feeder - ON / OFF / TRIP / Trip circuit healthy / DC supply healthy.

Outgoings:

160A 25KA TPN Motorised MCCB Microprocessor based with overload (adjustable), short circuit (fixed magnetic) & earth fault protection release with extended rotary handle - 03 Nos

125A 25KA TPN Motorised MCCB Microprocessor based with overload (adjustable), short circuit (fixed magnetic) & earth fault protection release with extended rotary handle - 03 Nos

63A 25KA TPN Motorised MCCB Microprocessor based with overload (adjustable), short circuit (fixed magnetic) & earth fault protection release with extended rotary handle - 03 Nos

All outgoing feeders shall be provided with Energy analyser (digital type) consisting of I, V, kW, kWH, kVA, PF, HZ, MDI (EM6400 of Conzerve or equi.) with RS-485 communication port for communication / report generation.

All outgoing feeders shall be provided with potential free contact for scada integration, one set of phase indication lamps and on,off, trip indication lamps with protection fuses/MCB.

Type I & II SPD 25kA/phase with suitable MCCB

Busbar

630 AMP ,415 Volts, 3 phase 50 HZ,TPN(4W),50kA, high conductivity Aluminium Alloy bus bar of suitable length, SMC / DMC supports, with colour coding and insulated by heat shrinkable sleeves and clip on shrouds for joints. The current density of bus bar shall be as per TTA design certified to IEC 61439.

Suitable Gland Plate To Be Provided For Each Incomers feeder As Per Mentioned Runs Of Cables In The Schematic Diagram.

Panel Switch Board Complete With All Internal Wiring, Name Plates And Complete In All Respects.

Note : GA drawings shall be got approved from Client(user)/ Architects / Consultants before fabrication.The panel has to be specifically fabricated as per the space available at site. The existing column positions will also be considered.

CAPACITOR BANK PANEL

Incoming:

1No - 125A 415V 25KA breaking capacity , 4P,MCCB

Lot-125A TPN, 415V, Short circuit rated 25KA for 1sec, Aluminium bus bars with busbar insulators, heat shrinkable PVC sleeves etc.

1 set- 125/5A currecnt transformer of class-1 and 15VA burden for metering.

1No-(0-125A)range digital type Ammeter.

1No-(0-500v)range digital type voltmeter.

1No MPCB for tapping power for metering & control circuit.

1set- RYB indicating lamps of LED module.

Outgoings:

16A 415V 16KA breaking capacity , TPN MCCB-2 No

MAIN PCC 2

630A ACB Incomers From Transformer-1 & DG-1 :

630A 50kA FP ACB Microprocessor release Motor wound spring charged closing mechanism (EDO),horizontal drawout type with over current,short circuit & earth fault protection release, screen display of measurements like Current : phase/ neutral/ earth, average, max,%loading, seq components, Voltage : Phase, Line, Average and with RS-485 Port - 1 Nos

Under Voltage relay / release with timer. - 1 Nos

TNC switch. - 1 Nos

3 CT's of ratio 630/5A, Class 1 accuracy 15 VA burden for metering. - 1 Set

3 CT's of ratio 630/5A, Class 5P10, accuracy 15 VA burden for PROTECTION . - 1 Set

Power Quality Meter (digital type) consisting of I, V, kW, kWH, kVA, PF, HZ, MDI,Capability of Disturbance Direction Detection,Sag & Swell Monitoring with Waveform Capturing Harmonics analysis upto 63rd order for Voltage & Current,(PM8000 series or equivalent) with Ethernet communication port. - 1 Nos

Restricted earth fault relay with PS class CT’s- 1 Set

LED type phase indicating lamps, each lamp shall be with backup MCB along with hooter, auxillary relay, 2 sets of push buttons.

LED type indicating lamp for indicating the status of feeder - ON / OFF / TRIP / Trip circuit healthy / DC supply healthy.

Outgoings:

250A 25KA TPN Motorised MCCB Microprocessor based with overload (adjustable), short circuit (fixed magnetic) & earth fault protection release with extended rotary handle - 02 Nos

160A 25KA TPN Motorised MCCB Microprocessor based with overload (adjustable), short circuit (fixed magnetic) & earth fault protection release with extended rotary handle - 02 Nos

63A 25KA TPN Motorised MCCB Microprocessor based with overload (adjustable), short circuit (fixed magnetic) & earth fault protection release with extended rotary handle - 04 Nos

All outgoing feeders shall be provided with Energy analyser (digital type) consisting of I, V, kW, kWH, kVA, PF, HZ, MDI (EM6400 of Conzerve or equi.) with RS-485 communication port for communication / report generation.

All outgoing feeders shall be provided with potential free contact for scada integration, one set of phase indication lamps and on,off, trip indication lamps with protection fuses/MCB.

Type I & II SPD 25kA/phase with suitable MCCB

Busbar

630 AMP ,415 Volts, 3 phase 50 HZ,TPN(4W),50kA, high conductivity Aluminium Alloy bus bar of suitable length, SMC / DMC supports, with colour coding and insulated by heat shrinkable sleeves and clip on shrouds for joints. The current density of bus bar shall be as per TTA design certified to IEC 61439.

Suitable Gland Plate To Be Provided For Each Incomers feeder As Per Mentioned Runs Of Cables In The Schematic Diagram.

Panel Switch Board Complete With All Internal Wiring, Name Plates And Complete In All Respects.

Note : GA drawings shall be got approved from Client(user)/ Architects / Consultants before fabrication.The panel has to be specifically fabricated as per the space available at site. The existing column positions will also be considered.

CAPACITOR BANK PANEL

Incoming:

1No - 125A 415V 25KA breaking capacity , 4P,MCCB

Lot-125A TPN, 415V, Short circuit rated 25KA for 1sec, Aluminium bus bars with busbar insulators, heat shrinkable PVC sleeves etc.

1 set- 125/5A currecnt transformer of class-1 and 15VA burden for metering.

1No-(0-125A)range digital type Ammeter.

1No-(0-500v)range digital type voltmeter.

1No MPCB for tapping power for metering & control circuit.

1set- RYB indicating lamps of LED module.

Outgoings:

16A 415V 16KA breaking capacity , TPN MCCB-2 No

Suppy, installation, testing, Design, manufacture, supply inspection, handling, assembling, affecting proper connections, testing and commissioning of 16 SWG CRCA sheet steel fabricated cubical type FMC Panel ,floor mounting, dust & vermin proof, front operated construction, enclosure class - IP 42, powder coated after proper treatment with 9 tank process with top/bottom removable gland plates, as required, double compression type cable glands, earth bus, hinged and lockable doors to achieve dust and vermin proof complete with all inter connections small wiring by min. 2.5 sq. mm. FRLS copper wires, ckt labels etc. The Aluminium Bus Bar shall be of suitable length, 415 volts, 3 phase 50 Hz TPN(4W), with withstanding impulse voltage 12kV. The panel feeders shall be suitable for terminating suitable nos. 3.5 / 4 core armoured aluminium cable or Aluminium Bus Duct as required.

Incoming from MPCC-2

160A 4P 25KA Motorised MCCB Microprocessor based release unit with overload (adjustable), short circuit (fixed magnetic) & earth fault protection release with potential free contact and extended rotary handle - 01 Nos

3 CT's of ratio 160/5A, Class 1.0 accuracy 15 VA burden for metering. - 1 Set

LED type phase indicating lamps, each lamp shall be with backup MCB, auxillary relay, 2 sets of push buttons. - 3 Nos

LED type indicating lamp for indicating the status of feeder - ON / OFF / TRIP.Each lamp shall be with backup MCB. - 3 Nos

Outgoing

63A 16KA TPN MCCB with overload, short circuit & earth fault protection release with extended rotary handle - 06 Nos

40A 16KA TPN MCCB with overload, short circuit & earth fault protection release with extended rotary handle - 3 Nos

Type II SPD 25kA/Phase with suitable MCCB - 1 Set

Busbar

160 AMP ,415 Volts, 3 phase 50 HZ,TPN(4W),25kA, high conductivity Aluminium bus bar of suitable length, SMC / DMC supports, with colour coding and insulated by heat shrinkable sleeves and clip on shrouds for joints.The current density of bus bar shall be as per TTA design certified to IEC 61439.

All Incomers & Outgoings Cable Entry From Top/bottom

Suitable Gland Plate To Be Provided For Each Incomers feeder As Per Mentioned Runs Of Cables In The Schematic Diagram.

Panel Switch Board Complete With All Internal Wiring, Name Plates And Complete In All Respects.

Note : GA drawings shall be got approved from Client(user)/ Architects / Consultants before fabrication.The panel has to be specifically fabricated as per the space available at site. The existing column positions will also be considered.

Suppy, installation, testing, Design, manufacture, supply inspection, handling, assembling, affecting proper connections, testing and commissioning of 16 SWG CRCA sheet steel fabricated cubical type WORKSHOP Panel ,floor mounting, dust & vermin proof, front operated construction, enclosure class - IP 42, powder coated after proper treatment with 9 tank process with top/bottom removable gland plates, as required, double compression type cable glands, earth bus, hinged and lockable doors to achieve dust and vermin proof complete with all inter connections small wiring by min. 2.5 sq. mm. FRLS copper wires, ckt labels etc. The Aluminium Bus Bar shall be of suitable length, 415 volts, 3 phase 50 Hz TPN(4W), with withstanding impulse voltage 12kV. The panel feeders shall be suitable for terminating suitable nos. 3.5 / 4 core armoured aluminium cable or Aluminium Bus Duct as required.

Incoming From MPCC-2

250A 4P 25KA Motorised MCCB Microprocessor based release unit with overload (adjustable), short circuit (fixed magnetic) & earth fault protection release with potential free contact and extended rotary handle - 01 Nos

3 CT's of ratio 250/5A, Class 1.0 accuracy 15 VA burden for metering. - 1 Set

LED type phase indicating lamps, each lamp shall be with backup MCB, auxillary relay, 2 sets of push buttons. - 3 Nos

LED type indicating lamp for indicating the status of feeder - ON / OFF / TRIP.Each lamp shall be with backup MCB. - 3 Nos

Outgoing

63A 16KA TPN MCCB with overload, short circuit & earth fault protection release with extended rotary handle - 12 Nos

40A 16KA TPN MCCB with overload, short circuit & earth fault protection release with extended rotary handle - 3 Nos

Type II SPD 25kA/Phase with suitable MCCB - 01 Set

Busbar

250A ,415 Volts, 3 phase 50 HZ,TPN(4W),25kA, high conductivity Aluminium bus bar of suitable length, SMC / DMC supports, with colour coding and insulated by heat shrinkable sleeves and clip on shrouds for joints.The current density of bus bar shall be as per TTA design certified to IEC 61439.

All Incomers & Outgoings Cable Entry From Top/bottom

Suitable Gland Plate To Be Provided For Each Incomers feeder As Per Mentioned Runs Of Cables In The Schematic Diagram.

Panel Switch Board Complete With All Internal Wiring, Name Plates And Complete In All Respects.

Note : GA drawings shall be got approved from Client(user)/ Architects / Consultants before fabrication.The panel has to be specifically fabricated as per the space available at site. The existing column positions will also be considered.

Suppy, installation, testing, Design, manufacture, supply inspection, handling, assembling, affecting proper connections, testing and commissioning of 16 SWG CRCA sheet steel fabricated cubical type Data Centre Panel ,floor mounting, dust & vermin proof, front operated construction, enclosure class - IP 42, powder coated after proper treatment with 9 tank process with top/bottom removable gland plates, as required, double compression type cable glands, earth bus, hinged and lockable doors to achieve dust and vermin proof complete with all inter connections small wiring by min. 2.5 sq. mm. FRLS copper wires, ckt labels etc. The Aluminium Bus Bar shall be of suitable length, 415 volts, 3 phase 50 Hz TPN(4W), with withstanding impulse voltage 12kV. The panel feeders shall be suitable for terminating suitable nos. 3.5 / 4 core armoured aluminium cable or Aluminium Bus Duct as required.

Incoming From MPCC-1

160A 4P 25KA Motorised MCCB Microprocessor based release unit with overload (adjustable), short circuit (fixed magnetic) & earth fault protection release with potential free contact and extended rotary handle - 01 Nos

3 CT's of ratio 160/5A, Class 1.0 accuracy 15 VA burden for metering. - 1 Set

LED type phase indicating lamps, each lamp shall be with backup MCB, auxillary relay, 2 sets of push buttons. - 3 Nos

LED type indicating lamp for indicating the status of feeder - ON / OFF / TRIP.Each lamp shall be with backup MCB. - 3 Nos

Outgoing

125A 16KA TPN MCCB with overload, short circuit & earth fault protection release with extended rotary handle - 03 Nos

63A 16KA TPN MCCB with overload, short circuit & earth fault protection release with extended rotary handle - 02 Nos

40A 16KA TPN MCCB with overload, short circuit & earth fault protection release with extended rotary handle - 04 Nos

Type II SPD 25kA/Phase with suitable MCCB - 1 Set

Busbar

160 AMP ,415 Volts, 3 phase 50 HZ,TPN(4W),25kA, high conductivity Aluminium bus bar of suitable length, SMC / DMC supports, with colour coding and insulated by heat shrinkable sleeves and clip on shrouds for joints.The current density of bus bar shall be as per TTA design certified to IEC 61439.

All Incomers & Outgoings Cable Entry From Top/bottom

Suitable Gland Plate To Be Provided For Each Incomers feeder As Per Mentioned Runs Of Cables In The Schematic Diagram.

Panel Switch Board Complete With All Internal Wiring, Name Plates And Complete In All Respects.

Note : GA drawings shall be got approved from Client(user)/ Architects / Consultants before fabrication.The panel has to be specifically fabricated as per the space available at site. The existing column positions will also be considered.

Feeder Piller-1

Supply and fixing of suitable out door feeder piller box of size made with 14 SWG CRCA sheet with double door arrangement, making powder coating after processing of 7 Tank process, lock and key, hinges, rubber gasket, danger board,suitable angle iron stand for mounting the feeder pillar with cement concrete.

Incoming From MPCC-1

125A 4P 25KA Motorised MCCB Microprocessor based release unit with overload (adjustable), short circuit (fixed magnetic) & earth fault protection release with potential free contact and extended rotary handle - 01 Nos

3 CT's of ratio 125/5A, Class 1.0 accuracy 15 VA burden for metering. - 1 Set

LED type phase indicating lamps, each lamp shall be with backup MCB, auxillary relay, 2 sets of push buttons. - 3 Nos

LED type indicating lamp for indicating the status of feeder - ON / OFF / TRIP.Each lamp shall be with backup MCB. - 3 Nos

Outgoing

63A TPN MCB - 02 Nos

40A TPN MCB - 03 Nos

32A TPN MCB with contactor & Timer. - 04 Nos

32A TPN MPCB with contactor & DOL starter. - 02 Nos

Type II SPD 25kA/Phase with suitable MCCB - 1 Set

Busbar

125A ,415 Volts, 3 phase 50 HZ,TPN(4W),25kA, high conductivity Aluminium bus bar of suitable length, SMC / DMC supports, with colour coding and insulated by heat shrinkable sleeves and clip on shrouds for joints.The current density of bus bar shall be as per TTA design certified to IEC 61439.

All Incomers & Outgoings Cable Entry From Top/bottom

Suitable Gland Plate To Be Provided For Each Incomers feeder As Per Mentioned Runs Of Cables In The Schematic Diagram.

Panel Switch Board Complete With All Internal Wiring, Name Plates And Complete In All Respects.

Note : GA drawings shall be got approved from Client(user)/ Architects / Consultants before fabrication.The panel has to be specifically fabricated as per the space available at site. The existing column positions will also be considered.

Feeder Piller-4

Supply and fixing of suitable out door feeder piller box of size made with 14 SWG CRCA sheet with double door arrangement, making powder coating after processing of 7 Tank process, lock and key, hinges, rubber gasket, danger board,suitable angle iron stand for mounting the feeder pillar with cement concrete.

Incoming From Feeder piller-1

63A 4P 16KA Motorised MCCB Microprocessor based release unit with overload (adjustable), short circuit (fixed magnetic) & earth fault protection release with potential free contact and extended rotary handle - 01 Nos

3 CT's of ratio 63/5A, Class 1.0 accuracy 15 VA burden for metering. - 1 Set

LED type phase indicating lamps, each lamp shall be with backup MCB, auxillary relay, 2 sets of push buttons. - 3 Nos

LED type indicating lamp for indicating the status of feeder - ON / OFF / TRIP.Each lamp shall be with backup MCB. - 3 Nos

Outgoing

63A TPN MCB - 03 Nos

32A DP MCB - 01 Nos

32A TPN MCB with contactor & Timer. - 03 Nos

32A TPN MPCB with contactor & DOL starter. - 02 Nos

Type II SPD 25kA/Phase with suitable MCCB - 1 Set

Busbar

63A ,415 Volts, 3 phase 50 HZ,TPN(4W),16kA, high conductivity Aluminium bus bar of suitable length, SMC / DMC supports, with colour coding and insulated by heat shrinkable sleeves and clip on shrouds for joints.The current density of bus bar shall be as per TTA design certified to IEC 61439.

All Incomers & Outgoings Cable Entry From Top/bottom

Suitable Gland Plate To Be Provided For Each Incomers feeder As Per Mentioned Runs Of Cables In The Schematic Diagram.

Panel Switch Board Complete With All Internal Wiring, Name Plates And Complete In All Respects.

Note : GA drawings shall be got approved from Client(user)/ Architects / Consultants before fabrication.The panel has to be specifically fabricated as per the space available at site. The existing column positions will also be considered.

Feeder Piller-5

Supply and fixing of suitable out door feeder piller box of size made with 14 SWG CRCA sheet with double door arrangement, making powder coating after processing of 7 Tank process, lock and key, hinges, rubber gasket, danger board,suitable angle iron stand for mounting the feeder pillar with cement concrete.

Incoming From MPCC-1

63A 4P 16KA Motorised MCCB Microprocessor based release unit with overload (adjustable), short circuit (fixed magnetic) & earth fault protection release with potential free contact and extended rotary handle - 01 Nos

3 CT's of ratio 63/5A, Class 1.0 accuracy 15 VA burden for metering. - 1 Set

LED type phase indicating lamps, each lamp shall be with backup MCB, auxillary relay, 2 sets of push buttons. - 3 Nos

LED type indicating lamp for indicating the status of feeder - ON / OFF / TRIP.Each lamp shall be with backup MCB. - 3 Nos

Outgoing

40A TPN MCB - 04 Nos

32A TPN MCB with contactor & Timer. - 02 Nos

32A TPN MPCB with contactor & DOL starter. - 02 Nos

Type II SPD 25kA/Phase with suitable MCCB - 1 Set

Busbar

63A ,415 Volts, 3 phase 50 HZ,TPN(4W),16kA, high conductivity Aluminium bus bar of suitable length, SMC / DMC supports, with colour coding and insulated by heat shrinkable sleeves and clip on shrouds for joints.The current density of bus bar shall be as per TTA design certified to IEC 61439.

All Incomers & Outgoings Cable Entry From Top/bottom

Suitable Gland Plate To Be Provided For Each Incomers feeder As Per Mentioned Runs Of Cables In The Schematic Diagram.

Panel Switch Board Complete With All Internal Wiring, Name Plates And Complete In All Respects.

Note : GA drawings shall be got approved from Client(user)/ Architects / Consultants before fabrication.The panel has to be specifically fabricated as per the space available at site. The existing column positions will also be considered.

Feeder Piller-2

Supply and fixing of suitable out door feeder piller box of size made with 14 SWG CRCA sheet with double door arrangement, making powder coating after processing of 7 Tank process, lock and key, hinges, rubber gasket, danger board,suitable angle iron stand for mounting the feeder pillar with cement concrete.

Incoming From MPCC-2

63A 4P 16KA Motorised MCCB Microprocessor based release unit with overload (adjustable), short circuit (fixed magnetic) & earth fault protection release with potential free contact and extended rotary handle - 01 Nos

3 CT's of ratio 63/5A, Class 1.0 accuracy 15 VA burden for metering. - 1 Set

LED type phase indicating lamps, each lamp shall be with backup MCB, auxillary relay, 2 sets of push buttons. - 3 Nos

LED type indicating lamp for indicating the status of feeder - ON / OFF / TRIP.Each lamp shall be with backup MCB. - 3 Nos

Outgoing

40A TPN MCB - 02 Nos

32A DP MCB - 02 Nos

32A TPN MPCB with contactor & DOL starter. - 02 Nos

32A TPN MCB with contactor & Timer. - 03 Nos

Type II SPD 25kA/Phase with suitable MCCB - 1 Set

Busbar

63A ,415 Volts, 3 phase 50 HZ,TPN(4W),16kA, high conductivity Aluminium bus bar of suitable length, SMC / DMC supports, with colour coding and insulated by heat shrinkable sleeves and clip on shrouds for joints.The current density of bus bar shall be as per TTA design certified to IEC 61439.

All Incomers & Outgoings Cable Entry From Top/bottom

Suitable Gland Plate To Be Provided For Each Incomers feeder As Per Mentioned Runs Of Cables In The Schematic Diagram.

Panel Switch Board Complete With All Internal Wiring, Name Plates And Complete In All Respects.

Note : GA drawings shall be got approved from Client(user)/ Architects / Consultants before fabrication.The panel has to be specifically fabricated as per the space available at site. The existing column positions will also be considered.

Feeder Piller-3

Supply and fixing of suitable out door feeder piller box of size made with 14 SWG CRCA sheet with double door arrangement, making powder coating after processing of 7 Tank process, lock and key, hinges, rubber gasket, danger board,suitable angle iron stand for mounting the feeder pillar with cement concrete.

Incoming From MPCC-2

63A 4P 16KA Motorised MCCB Microprocessor based release unit with overload (adjustable), short circuit (fixed magnetic) & earth fault protection release with potential free contact and extended rotary handle - 01 Nos

3 CT's of ratio 63/5A, Class 1.0 accuracy 15 VA burden for metering. - 1 Set

LED type phase indicating lamps, each lamp shall be with backup MCB, auxillary relay, 2 sets of push buttons. - 3 Nos

LED type indicating lamp for indicating the status of feeder - ON / OFF / TRIP.Each lamp shall be with backup MCB. - 3 Nos

Outgoing

40A TPN MCB - 03 Nos

32A DP MCB - 01 Nos

32A TPN MCB with contactor & Timer. - 03 Nos

Type II SPD 25kA/Phase with suitable MCCB - 1 Set

Bus Bar

63A ,415 Volts, 3 phase 50 HZ,TPN(4W),16kA, high conductivity Aluminium bus bar of suitable length, SMC / DMC supports, with colour coding and insulated by heat shrinkable sleeves and clip on shrouds for joints.The current density of bus bar shall be as per TTA design certified to IEC 61439.

All Incomers & Outgoings Cable Entry From Top/bottom

Suitable Gland Plate To Be Provided For Each Incomers feeder As Per Mentioned Runs Of Cables In The Schematic Diagram.

Panel Switch Board Complete With All Internal Wiring, Name Plates And Complete In All Respects.

Note : GA drawings shall be got approved from Client(user)/ Architects / Consultants before fabrication.The panel has to be specifically fabricated as per the space available at site. The existing column positions will also be considered.

Supply of CPRI tested maintenance free ,Low carbon mild steel copper coated earth rod of 3 metre electrode having diameter of 14.2 mm with copper coating thickness of 250micron tested as per IEC 62561-2 & is provided with universal clamp made of SS to connect rod with flat conductor. Earth conductivity enhancing compound shall be of 25 kg/pit tested as per IEC 62561-7,TCLP tested. The above arrangements shall be provided with Heavy duty earth champer of 5000kg load bearing capacity to ensure the safety of earthing system.

Providing and fixing earth bus of 50x6mm Hot Dip Galvanized GI strip

Providing and fixing earth bus of 25x6mm Hot Dip Galvanized GI strip

Providing and fixing 25 mm X 5 mm copper strip on surface or in recess for connections etc. as required.

SUBHEAD XXXVI : AREA LIGHTING

Supply, erection and commissioning of individual 3mtr (600mm below Ground) high 50mm dia Class B GI pole, complete with base plate FRP terminal box, wiring from terminal box to the fixture with 3core 2.5Sq.mm multistrand Copper conductor cable, MCB control and 2nos of 40mm dia class B GI pipe for incoming and outgoing cablesetc including PCC foundations, pedestal and Supply and installation of 45W LED Lamp Post top Lantern fixture Integral type with Lamp and Controlgear/driver. (Philips/Wipro/Crompton similar catalog number to Wipro :LP07-501-XXX-57-CL)

Supply and erection of steel stepped and swaged tubler poles of 9mtr. Long (410 SP25) (1.5mtr below Ground) with base plate, earthing studs,1.5Mtr out reach single arm, FRP terminal box, 2nos 50mm diaclass B GI Pipe, 1.5mtr. Long for incoming and outgoings cables, including PCC Pedestal complete with painting with black bitumin paint inside the coping for embedded portion and two coats of Zinc chromate primer and two coats of Aluminium paint externally for length above the ground. The pole shall be with Junction box consisting of MCB. The wiring from Junction box to Light fixture shall be carried out with 3core 2.5sq.mm multistrand conductor cable. The Pole shall be fixed with 70W LED Lamp with fixture including supply of Controlgear/driver and lamp (Philips/Wipro/Crompton similar catalog number to (Wipro : LR02-781-XXX-57-G2 )

Supply, erection and commissioning of individual Gate Lights with 0.6mtr long 50mm dia Class B GI pole complete with base plate FRP terminal box, wiring from terminal box to the fixture with 3Core 2.5sq.mm copper wire, MCB Control and 40mm dia Class B GI pipe for incoming and outgoing cables as per drawing etc and Supply and installation of 45W LED fixture. (Philips/Wipro/Crompton similar catalog number to Similar to Wipro :LP07-501-XXX-57-CL)

Supply, testing & commisioning of following size 1.1KV grade XLPE insulated armoured aluminium conductor cable.The cable shall conform to IS 7098/ Part I.

4Core 16 sq.mm

Laying of one number PVC insulated and PVC sheathed I XLPE power cable of 1.1 kV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc. as required.

Up to 35Sq.mm

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 kV grade of following size in the existing RCC/ HUMEI METAL pipe as required.

Upto 35 sq. mm

Supplying and fixing cable route marker with 10 em X 10 em X 5 mm thick G.l. plate with inscription there on, bolted /welded to 35 mm X 35 mm X 6 mm angle iron, 60 cm long and fixing the same in ground as required.

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed I XLPE aluminium conductor cable of 1.1 kV grade as required.

4Core 16 sq.mm

Providing Spiral coil earthing with 8 SWG GI wire including spreading of salt and charcoal as per IS 3043/87 with latest amendments.

Supply, erection and commissioning of of 12.5mtr height flood light with light fixtures including high mast of 12 side polygonal tappered type of 360mm dia(bottom) to 100mm dia at top, lantern carriage assembly, winch assembly, FLP power tool for winch drive, feeder pillar box, distribution boards/ switches, necessary cabling from feeder pillar to individual lighting fixtures, providing aviation obstruction light etc complete in all respects and as directed by the engineer-in-charge.

Supplying and laying of 63 mm dia (OD-63 mm & ID-51 mm nominal) DWC pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc. in the existing trench, complete as required

Supply and transportation of Integrated IP 65 Solar Street Light with ABS + Polycarbonate body , Poly crystal Solar panel with pool white SMD LED Light, Beam angle 120 degrees, Reflector, Charging time is minimum 6 Hrs and maximum 8 Hrs, Lighting Time 10 to 12 Hrs (Subject to using dusk to dawn /Induction Mode / Duration Mode of Timers), used High efficiency LiFe PO 4, Battery, Dusk to dawn sensor, Induction Mode, Auto dim and Auto Bright, Motion sensor and also facilitate duration based timer of 2 / 4 / 6 Hrs.

SUBHEAD XXXVII : ARBORICULTURE

TREE PLANTATION

Digging holes in ordinary soil and refilling the same with the excavated earth mixed with manure or sludge in the ratio of 2:1 by volume (2 parts of stacked volume of earth after reduction by 20% : 1 part of stacked volume of manure after reduction by 8%) flooding with water, dressing including removal of rubbish and surplus earth, if any, with all leads and lifts (cost of manure, sludge or extra good earth if needed to be paid for separately) :

Holes 90 cm dia, and 90 cm deep

Providing and Stacking of tree saplings of height 90-120 cm, well developed with stem in big size HDPE bag as per the direction of Officer-in-Charge.

Anti termite treatment by digging pits 30 cm deep and 4 cm dia, 6 to 7 holes around the tree using chemical emulsion at the rate of 1.5 itres per hole in two time or more application to get the trees free from termite infection chemicals used Chloropyriphos 20% EC in the ration of 1% concentration and as per direction of Officer-in-charge.

Plantation of Trees at site i/c watering and removal of unserveiceable material's as per direction of Officer-in-charge (excluding cost of plant & water)

i) Trees Plant

SHRUB / HEDGE / CREEPER

Digging holes in ordinary soil and refilling the same with the excavated earth mixed with manure or sludge in the ratio of 2:1 by volume (2 parts of stacked volume of earth after reduction by 20% : 1 part of stacked volume of manure after reduction by 8%) flooding with water, dressing including removal of rubbish and surplus earth, if any, with all leads and lifts (cost of manure, sludge or extra good earth if needed to be paid for separately) :

Holes 60 cm dia, and 60 cm deep

Providing and Stacking of Allamanda cathartica of height 30 cm to 45 cm, as per the direction of Officer-in-Charge.

Providing and Stacking of Bignonai venusta (Golden shower) of height 30 cm to 45 cm, as per the direction of Officer-in-Charge.

Providing and Stacking of Bougainvillea (Variety Butiana, Lady Mary Baring, Mahara, Mohan, Scarlet Queen, Variegated, Glabra Formosa, Peruviana Odissi, Paratha, Subhra, Thimma, Spectabilis L.N. Birla, Refulgens) of height 30 cm to 45 cm with 2-3 branches, as per the direction of Officer-in-Charge.

Providing and displaying of Adenium pink Obesum grafted well developed with fresh & healthy 30 to 60 cm ht. as per the direction of Officer-in-Charge.

Providing and Stacking of Caesalpinia pulcherrima species of height 45-60 cm, as per the direction of Officer-in-Charge.

Providing and stacking of Duranta Golden having ht 15 to 20 cm bushy shape with fresh and healthy leaves, as per direction of the officer-in-charge.

Plantation of Shurbs / Hedges / Creeper at site i/c watering and removal of unserveiceable material's as per direction of Officer-in-charge

i) Shurbs/Hedges/Creeper Plant

Trenching in ordnary soil up to a depth of 30 cm including removal and stacking of serviceable materials and then disposing of surplus soil, by spreading and neatly levelling within a lead of 50 m and making up the trenched area to proper levels by filling with earth or earth mixed with sludge or / and manure in the ratio of 8:1 (8 Parts of stacked volume of earth after reduction by 20% : one part of stacked volume of sludge or manure after reduction by 8%), before and after flooding trench with water (excluding cot of imported earth, sludge or manure)

Rough dressing the trenched ground including breaking clods

Uprooting weeds from the trenched area after 10 to 15 days of its flooding with water including disposal of uprooted vegetation.

Fine dressing of the ground

Anti termite treatment of lawn area through premise 30.50% I.P. one litre premise diluted in 499 litres water and applying solution @ 1.00 litre solution per sqm lawn or bed area. (two application) i/c cost of chemical and as per direction of Officer-in-charge

Providing & laying Bermuda Dibbling grass turf with earth 50mm to 60mm thickness of existing ground prepared with proper level and ramming with tools wooden and than rolling the surface with light roller make the surface smoothen and light watering the same, with sprinkler and maintenance for 30 days or more till the grass established properly as per direction of officer in charge.

Good Earth: Supplying and stacking of good earth at site including royalty and carriage upto 5 km complete (earth measued in stacks will be reduced by 20% for payment)

Sludge: Supplying and stacking sludge at site including royalty and carriage upto 5 km complete (sludge measued in stacks will be reduced by 8% for payment)

Manure: Supplying and stacking at site dump manure from approved source, including carriage upto 5 km lead complete (Manure measued in stacks will be reduced by 8% for payment) Screened through sieve of I.S designation 20 mm

Spreading of Sludge, dump manure and / or good earth in required thickness as per direction of Officer-in-charge (cost of sludge, dump manure and / or good earth to be paid seperately)

ORNAMENTAL PLANTS (POTTED PLANTS)

a) Providing and Displaying Bird of paradise / Ficus nuda / Ficus resnold / Furcaria Variegated / plant well developed with fresh & healthy 90 to 120 cm ht in 45 cm Earthen Pot / Plastic Pot as per direction of the Officer-in-charge.

MAINTENANCE

1) Complete maintenance of the entire garden features having as per yard stick in the garden area i.e. lawn trees, shurbs, hedge, flower beds, foliages, creepers etc. including hoeing, weeding pruning replacement of plants, gap filling, watering, mowing of lawn, grass cutting by lawn mover and brush cutter , removal of garden waste, applying insecticide, pesticide & fertilizers(whenever required) top dressing of lawn with good earth and manure and maintenance of other garden related works as directed by office-in-charge (Cost of Good Earth, Manure, Fertilizer, Insecticide , Pesticide, Lawn Mover and brush cutter with fuel will be the Department & other T & P materials/articles shall be provided by the contractor.)

SSC PROJECTS PRIVATE LIMITED

RIC Projects Pvt. Ltd.

S. R. ASHOK & ASSOCIATES PVT. LTD.

VISHAL BUILDERS

RMS CONSTRUCTION PVT. LTD.

SHRI GURMUKHDAS CONTRACTORS PVT. LTD.

Vishal Infrastructure Ltd

Rds Project ltd.

CH.VEERARAGHAVULU CONSTRUCTION PVT LTD

SVC PROJECTS PVT LIMITED

RVR PROJECTS PRIVATE LIMITED