REPAIR TO ROOF, FALSE CEILING, CHAJJA, ROOF TREATMENT, PLINTH PROTECTION, JOINERY AND REPAIR OF ALUMINIUM DOOR AND WINDOW FOR AGE B/R-I AT DINJAN MIL STN

Amount

Dismantling of asbestos cement (corrugated or semi corrugated) sheets in roof coverings including ridges complete all as specified and as directed.

S&F for 6 mm thick asbestos cement sheet, corrugated or semi corrugated sheets as in roofs, etc. and fixed with 'L' type or 'J'-type or cranked hook bolts, complete all as specified and as directed.

S&F for 6 mm thick asbestos cement two piece adjustable serrated ridge for corrugated or semi corrugated asbestos cement sheet, fixed with 'L' type or 'J' type hook or cranked hook bolt with washer complete all as specified and as directed.

Fixing only asbestos cement sheet (corrugated) as in roof coverings using new 'L' type or 'J -type' or crank hook bolts complete all as specified and as directed. Note : Old serviceable asbestos cement roof sheet obtained from item No. 01 shall be used.

Dismantling of wrought iron or mild steel work of any description not otherwise provided for complete all as specified and as directed.

S&F for rolled mild steel work as in trusses, purlins, posts etc using angle, or tee sections, fixed independently, without connecting plates, etc including cutting, welding, drilling holes etc steel section conforming to Fe-290 (Gde E-165) complete all as specified and as directed.

M&L for preparation of new steel surfaces of any description over 10 cm in width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of zinc chrome red oxide primer complete all as specified and as directed.

M&L for plain cement concrete 1:2:4, type B-1 (using 20mm graded stone aggregate) as in coping etc including form works complete all as specified and as directed.

S&F for pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of profile as approved, any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed.

S&F for pre-painted galvalume aluminium zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in ridges/valley gutter, fixed with self tapping screws complete all as specified and as directed.

Demolition of plain cement concrete (unreinforced) in ground floors and pavings not exceeding 15cm thickness (below or above ground level) complete all as specified and as directed.

Demolition of reinforced cement concrete in any description including cutting reinforcement as required to facilitate demolition of concrete complete all as specified and as directed.

M&L for 75 mm thick, plain cement concrete 1:3:6, type C-2 (using 40mm graded stone aggregate) as in plinth protection laid in proper slope/gradient etc, finishing cement concrete surface even and smooth without using extra cement including making joints with bitumastic filing in proportion of bitumen and sand (1:2) complete all as specified and as directed.

M&L for reinforced cement concrete 1:2:4, type B-1 (using 20 mm graded stone aggregate) as in roof projection, cjajjas, kerbs, etc complete all as specified and as directed.

M&L for use and waste form work to soffits and egdes concrete flats, chajjas and the similar works for flat rough finished surfaces of concrete complete all as specified and as directed.

M&L for TMT steel bars 10mm dia and over cut to length, bend to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips quality complete all as specified and as directed.

M&L for TMT steel bars 6 to 10mm dia, cut to length, bend to shape required, including cranking, bending spirally as in tie/stirrups of columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and as directed.

Taking down cement plaster on brick or stone walls etc including racking out joints, hacking for key, scrubbing down with water complete all as specified as and directed

M&L for rendering 15 mm thick in cement mortar (1:4) on fair faces of brick masonry or concrete surfaces and finishing surfaces even and smooth without using extra cement complete all as specified and as directed.

M&L for 25mm thick cement concrete type B-0, 1:2:4 (using 12.5mm graded aggregate) finished even and smooth without using extra cement to receive WPT complete all as specified and as directed.

M&L for water proofing treatment on RCC roof etc. comprising with the following operation and as specified herein below and as directed :- (a) Taking down existing old tarfelt, bituminous compound including plaster etc, cleaning and removing debris to a distance exceeding 100m and not exceeding 250m. (b) 15 mm thick plastering in cement mortar (1:4) finished even and smooth. (c) Preparing and cleaning of fully dried cement plastered surface. (d) Applying one coat of cold bituminous primer to the plastered surface @ 0.25 liters per sqm conforming to IS-3384 (e) A layer of APP based polymeric membrane membrane 3mm thick (minimum) weighing 3.5 kg per sqm reinforced with polyster non woven fabric (weighing not less than 160 gms/sqm )shall be applied over bituminous primer as specified above. Application of polymeric membrane shall be by torch application. The over lap shall be minimum 100 mm on transverse direction and 75 mm in longitudinal direction. (f) One coat of aluminium paint over the APP based membrane @ 0.11 Kg/Sqm

M&L for cutting out cracks to V-sectionn exceeding 10cm wide and deep in existing roofs or terracing, walls etc. including cleaning out and filling solidly with a hot mixture of bitumen and clean dry sand 1:1 (by weight) complete all as specified and as directed.

M&L for Disconnecting existing PVC tanks of any description, of capacity exceeding 250 litres but not exceeding 500 litres, setting aside for cleaning and removing all scale and dirt/dust from existing PVC tank and hoisting, reconnecting and refixing in position including inlet-outlet pipe at opening portion and at mouth etc complete all as specified and as directed

M&L for Disconnecting existing PVC tanks of any description, of capacity exceeding 500 litres but not not exceeding 1000 litres setting aside for cleaning and removing all scale and dirt/dust from existing PVC tank and hoisting, reconnecting and refixing in position including inlet-outlet pipe at opening portion and at mouth etc. complete all as specified and as directed

Taking up or down 20 mm bore steel tubing and connections and keeping serviceable pipes in safe custody for reuse in the work complete all as specified and as directed.

Refixing of 20 mm bore, steel tubing and connections in new or old position in walls, ceiling or floors, etc with new fittings as required and cleaning of pipe complete all as specified and as directed. Note : Serviceable steel tubing shall be obtained from item No. 25 above.

Dismantling wall and ceiling boards (fibre, pulp, insulation etc.) any thickness including cover fillets and frame work any type complete all as specified and as directed.

M&L for GI frame work for false ceiling seamless comprising of galvanised iron perimeter channel 0.55mm thick with two unequal flangeds of 20 and 30mm and web of 27mm fixed to surrounding wall using nylon sleeves and screws at 450mm centre to centre / intermadiate channel 0.90mm thick having two equal flanges of 15mm each and web of 45mm suspended from soffit at approx 900mm centre to centre using 4mm dia GI (upto 1200mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flat 40X3mm size 60mm long and expansion hold fasteners 12.5mm dia 40mm long includin providing 08mm thick seamless calcium silicate ceiling made out of 1800X1200mm size board of siliceous and calcareous materials reinforced with cellulose fibre fixed to the ceiling section with 25mm long self drilling and tapping screwshaving philips head with under head cutter at 200mm centre to centre, including finishing the joints of face board with specially formulated jointing compound and 48mm wide fibre tape to provide seamless finish complete all as specified and as directed. Make : Eternit Everest/Lafarge/Armstrong.

M&L for 8 mm thick seamless calcium silicate ceiling made out of 1800x1200mm size board of siliceous and calcareous material reinforced with cellulose fibre fixed to the ceiling section with 25mm long self drilling and tapping screws having phillips head with under head cutter at 200 mm centre to centre, including finshing the joint of face to centre, board with specially formulated jointing compound and 48 mm wide fibre tape to provide seam less finish complete all as specified and as directed. Note : Frame work for ceiling shall be measured and paid separately.

M&L for second class hard wood mouldings as in cornices, picture rails and the like, sectional area exceeding 13Sqcm and not exceeding 25Sqcm fixed with nails in ceilings complete all as specified and as directed.

Dismantling timber scantlings of fillets, rails, post, rafters etc under 40Sqcm in section (unframed work), in any position complete all as specified and as directed.

M&L for second class hard wood plain fillets, square, rectangular in section in clean sawn, sectional area exceeding 13Sqcm and not exceeding 25Sqcm fixed/secured with nails in ceilings complete all as specified and as directed.

M&L for second class hard wood plain fillets, square,triangular, rectangular in section, bullnosed, splayed, chamfered or rounded on one edge or face, sectional area exceeding 06Sqcm and not exceeding 13Sqcm fixed/secured with nails in ceilings complete all as specified and as directed.

Fixing only old serviceable hard wood plain fillets, square,triangular, rectangular in section, sectional area exceeding 06Sqcm and not exceeding 13Sqcm fixed/secured using new nails in ceilings complete all as specified and as directed. Note : Old serviceable fillets obtained from item No. 31 shall be used.

S&F for aluminium anodised snap grid frame work of size 600mmx600mm frame work for ceiling with aluminium tee section of size 23.5mm x 26.4mm x 1.4mm thick and aluminium angle section of size 36.5mmx25mmx1.4mm thick for false ceiling including hangers 4 mm dia G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40x3mm size 60mm long and expansion hold fasteners 12.5mm dia, 40mm long including 4 mm thick non asbestos E-board (plain), HSPC fixed to frame including providing three coats of white wash complete all as specified and as directed. Make : Eternit Everest/Lafarge/Armstrong/Visaka Industries Ltd

M&L for 4mm thick non asbestos fibre cement building boards fixed or laid/ inserted to timber/GI/Aluminium framework with screws complete all as specified and as directed.

M&L for applying two coat of oil bound distemper over a coat of primer and 2mm thick wall care putty on newly surfaces of seamless calcium silicate ceiling complete all as specified and as directed.

M&L for preparation of surfaces of ceiling and applying two coat of oil bound distemper over a coat of primer all as as directed.

Supply only liquid water proofing compound complete all as specified and as directed. Make : Dr FIXIT/Fosroc/choksey

S&F for mild steel screw bolts of 5 to 10mm dia of neck (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, length of bolt n. exc 5cm long complete all as specified and as directed.

Dismantling timber boarding, any description, fixed in any position with nails complete all as specified and as directed.

M&L for 20 mm thick, second class hard wood boarding, clean sawn, planed one side with butt joints and fixed with nails in any situation as in eaves board, etc complete all as specified and as directed.

M&L for preparation of new or previously untreated wood and wood based surfaces of any description, not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed.

Taking down chowkats or frame, n.exceeding 1.5Sqm in each with shutters (without taking off shutter from the frame) complete all as specified and as directed.

Taking down chowkats or frames exceeding 1.5Sqm but not exceeding 4.0Sqm in each with shutter (without taking off shutter from the frame) complete all as specified and as directed.

Taking down shutters of any description not exceeding 1.0Sqm each complete all as specified and as directed.

Taking down shutters of any description exceeding 1.0Sqm but not exceeding 2.0Sqm each complete all as specified and as directed.

S&F for pressed steel frames for doors local work shop made of size 105x60mm with one or more rebates using cold rolled commercial mild steel sheet of 1.2mm thick including necessary fixing lugs, 100mm butt hinges, lock strike plate, etc and PCC filling of hollow section using plain cement concrete 1:3:6 type C-1 complete all as specified and as directed.

S&F for pressed steel frames for doors local work shop made of size 125x60mm with one or more rebates using cold rolled commercial mild steel sheet of 1.2mm thick including necessary fixing lugs, 100mm butt hinges, lock strike plate, shock absorber etc and PCC filling of hollow section using plain cement concrete 1:3:6 type C-1 complete all as specified and as directed.

M&F for well seasoned 2nd class hard wood plain, solid, straight chowkat and frames, wrought, framed, rebated on the solid rounded or chamfered, put together with glue pinned at joints complete all as specified and as as directed.

S&F for mild steel small articles using flat iron of size 25x3mm thick such as band, strap, hold fast, cleat, support, hook, hinges, base tie for door frame etc and other similar items conforming to Fe-290, Gde E-165 complete all as specified and as directed.

M&L for plain cement concrete 1:3:6, type C-1 (using 20mm graded stone aggregate) for embedding holdfast, bed block, cills, etc including necessary form work complete all as specified and as directed.

Taking down shutters of any description and refixing in existing location/opening not exceeding 1.0Sqm each including resecuring or easing and adjusting also refixing existing serviceable builders hardware complete all as specified and as directed.

Taking down shutters of any description and refixing in existing location/opening exceeding 1.0Sqm but not exceeding 2.0Sqm each including resecuring or easing and adjusting also refixing existing serviceable builders hardware complete all as specified and as directed.

M&L for 35mm thick 2nd class hard wood plain, framed, panelled shutters (any number of panels), with panels of 12mm thick veneered particle board medium density with commercial face veneers supplied and fitted to chowkats complete all as specified and as directed.

S&F for 40 mm thick factory made flush door shutter, solid core construction, with particle board core and plywood face panels, commercial type on both sides with internal jointless lipping not less than 25 mm depth complete all as specified and as directed.

S&F for solid PVC door frames of size 50mm x 95mm made out of 5mm plain colour PVC sheet reinforced with MS square tube complete all as specified and as directed.

S&F for factory made solid PVC moulded door shutter, 28 to 30 mm thick (stiles), with 2,4 or 6 raised panel design with 2mm thick 3D wood grain moulded PVC sheet polyurethane painted on the front face and 2mm thick plain colour PVC sheet on back face all as directed and as per specification and drawing shown in SSR Part II, 2010.

S&F for 30 mm thick, second class hardwood glazed and skeleton window/ventilator shutters open rebated and prepared to receive glass, gauge, etc, divided in to squares, with plain, chamfered or rounded, mitred and rebated sash bars, any numbers, edges of framing plain, chamfered or rounded complete all as specified and as directed in SSR Part I Section 8 clause 8.24 (b).

S&F for 35 mm thick, second class hardwood glazed and skeleton shutters open rebated and prepared to receive glass, gauge, etc, divided in to squares, with plain, chamfered or rounded, mitred and rebated sash bars, any numbers, edges of framing plain, chamfered or rounded complete all as specified and as directed in SSR Part I Section 8 clause 8.24 (a).

S&F for solid PVC door frames of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube complete all as specified and as directed.

S&F for factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded, plain colour PVC 'C' channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, panelling of plain colour 5mm thick PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement, as per specification and drawing and as directed.

S&F for aluminium alloy anodised sliding door bolt with hasp & staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy, length of bolt of 300mm anodised finish complete all as specified and as directed.

S&F for 150mm long, aluminium, barrel tower bolts of extruded section of aluminium alloy, anodised finish complete all as specified and as directed.

S&F for 100mm long aluminium, barrel tower bolts of extruded section of aluminium alloy, anodised finish complete all as specified and as directed.

S&F for 100mm size butt hinges, medium weight, cold rolled mild steel complete all as specified and as as directed.

S&F for 100mm size, butt hinges, stainless steel fixed with cadmium coated screws complete all as specified and as directed.

S&F for 75mm size, butt hinges, medium weight, cold rolled mild steel complete all as specified and as directed.

S&F for 150mm size aluminium handles, cast type, anodised to a bright natural, mat finish complete all as specified and as directed.

S&F for 100mm size aluminium handles, cast type, anodised to a bright natural, mat finish n complete all as specified and directed.

S&F for 150mm size aluminium shutter/gate hook and eye, cast type, anodised to a bright natural, mat finish complete all as specified and as directed.

S&F for galvanised mild steel wire cloth 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks or galvanised wire staples including timber bead complete all as specified and as directed.

S&F in repairs aluminium alloy anodised sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy, length of bolt of 300 mm anodised finish complete all as specified and as directed.

S&F in repairs 150mm long aluminium, barrel tower bolts of extruded section of aluminium alloy, anodised finish complete all as specified and as directed.

S&F in repairs 100mm long aluminium, barrel tower bolts of extruded section of aluminium alloy, anodised finish complete all as specified and as directed.

S&F in repairs 100mm size, butt hinges, medium weight, cold rolled mild steel complete all as specified and as directed.

S&F in repairs 75mm size butt hinges, medium weight, cold rolled mild steel complete all as specified and as directed.

S&F in repairs 150mm size aluminium handles, cast type, anodised to a bright natural, mat finish complete all as specified and as directed.

S&F in repairs 100mm size aluminium handles, cast type, anodised to a bright natural, mat finish complete all as specified and as directed.

S&F in repairs 150mm size aluminium shutter/gate hook and eye, cast type, anodised to a bright natural, mat finish complete all as specified and directed.

S&F for anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc complete all as specified and as directed.

S&F for anodised aluminium door shutters, using aluminium section weighing not less than 0.55Kg per metre including necessary joining cleats, glazing clips, rubber neoprene packing, aluminium handles 2 numbers in each shutter, hinges, anodised aluminium snap beading, screws etc complete all as specified and as directed.

S&F for anodised aluminium window and ventilator shutters, fixed type, with or without sash bar, using aluminium section weighing not less than 0.55Kg per metre including necessary joining cleats, glazing clips, rubber neoprene packing, aluminium handles 2 numbers in each shutter, hinges, anodised aluminium snap beading, screws etc complete all as specified and as directed.

M&L for mild steel framed work such as grills, gratings, etc., with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bar, barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks and similar work conforming to Fe-290 Gde E-165 complete all as specified and as directed.

S&Ffor double action floor spring hydraulically regulated made up of 1.25mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty complete all as specified and as directed.

S&F in repairs brass mortice lock, 4 levers, vertical type, 100mm size with at least 3 numbers key complete all as specified and as directed.

S&F in repairs mild steel 300mm, ordinary arrow pattern springs for doors including roller and roller plate complete all as specified and as directed.

M&L for preparation of ends of posts, back of chowkats etc new or previously untreated, wood and wood based materials or steel and iron works and treating with coal tar black paint, area of tarred exceeding 0.10Sqm but not exceeding 0.50Sqm each complete all as specified and as directed.

M&L for preparing surfaces of wood and wood based materials, steel and iron works, new or old of any description and girth treating small articles such as holdfasts etc area not exceeding 0.10Sqm each with tar or coal tar black paint complete all as specified and as directed.

S&F in repairs galvanised mild steel wire cloth 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks or galvanised wire staples including timber bead complete all as specified and as directed.

Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or steel frames, concrete or brick surrounds, glazed with putty or fixed with beads complete all as specified and as directed.

S&F for 3mm thick, sheet glass, ordinary quality and glazing with oil putty in square not exceeding 0.5Sqm in each pane complete all as specified and as directed.

S&F for 3mm thick, figured glass, pin head type and glazing with oil putty in square not exceeding 0.5 Sqm in each pane complete all as specified and as directed.

M&L for Preparation of new or previously untreated wood and wood based surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed.

M & L for preparation of new steel surfaces of any description, over 10cm in width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of zinc chrome red oxide primer complete all as specified and as directed.

M&L for preparation of old painted surfaces of steel any description over 10cm in width or girth, not otherwise described and applying one coat of synthetic enamel paint complete all as specified and as directed.

M&L for preparation of old painted surfaces of steel any description over 10cm in width or girth not otherwise described and applying one coat of synthetic enamel paint complete all as specified and as directed.

M&L for rendering 15 mm thick in two layer (10mm+ 5mm thick) on fair faces of brick work or concrete surfaces in cement mortar (1:4) mixed with water proofing compound at top 5mm thick layer by weight of cement as per manufacturer's instructions and finished the surface even and smooth without using extra cement complete all as specified and as directed. Note : WPC shall be measured and paid separately against relevant item.

M&L for rendering 10 mm thick in cement mortar (1:6) on other than fair faces of brick masonry or concrete surfaces and finishing the surfaces even and smooth without using extra cement complete all as specified and as directed.

M&L for preparation of new plastered surfaces of walls and applying two coats of colour wash using mineral colour complete all as specified and as directed.

M&L for preparing plastered surfaces of walls and applying two coats of distemper-oil-emulsion over a coat of primer over a coat of wall care putty (minimum 1mm thick) complete all as specified and as directed.

S&F in repairs curtain/harrison rails, including brackets, fancy type, 20mm dia, aluminium powder coated matching with brackets etc complete all as specified and as directed.

S&F in repairs curtain/harrison rails, 20mm dia, mild steel, chromium plated with fixing brackets, stops, rollers, etc complete all as specified and as as directed.

M&L for providing pelmet boxes in repair using 12mm thick particle board, medium density, flat pressed, single layer type with BWR type adhesive, fixed with screws complete all as specified and as as directed.

S&F in repairs cast iron body door closer, hadraulically regulated, designated No 3, universal type, suitable for door shutters of 851 to 1000mm in width and weight between 61 to 80 KG complete all as specified and as directed.

Dismantling timber scantlings 40 Sq.cm and over in section, in any position complete all as specified and as directed.

M&L for second class hardwood, scantlings, clean sawn, in unframed work complete all as specified and as directed.

M&L for 18/19mm thick prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work complete all as specified and as directed.

S&F for prelaminated MDF board 5.5mm thick DWR Grade -1 with one side laminates wooden texture as approved fixed to wall all as specified and as directed. Make : Century/Greenply/Kitply.

S&F in repairs 8mm thick aluminium deco grill size of 75x75mm fixed to window with aluminium flat 30x3mm complete all as specified and as directed.

Vicky Construction

M/s GANDHESWAR PHUKAN

MAZUMDAR ENTERPRISE

Kaushik Enterprises

FREEZCON

Bimal Trading Company

NChetia and Sons Trading