Construction of 30 Bedded Hospital at Minicoy Island, Lakshadweep (Re Tender-V)

Amount

Earth work in surface excavation not exceeding 30 cm in depth but exceeding 1.5 m in width as wellas 10 sqm on plan including getting out and disposal of excavated earth upto 50 m and lift upto 1.5 m, as directed by Engineer-in- Charge:All kinds of soil

Surface dressing of the ground including removing vegetation and in-equalities not exceeding 15 cm deep and disposal of rubbish, lead up to 50 m and lift up to 1.5 m. All kinds of soil.

Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete.

Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge. All kinds of soil

Extra for every additional lift of 1.5 m or part thereof in excavation / banking excavated or stacked materials. All kinds of soil

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.

Excavating, supplying and filling of local earth (including royalty) by mechanical transport upto a lead of 5km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete.

Disposal of earth work by mechanical transport including loading, transporting, unloading to approved municipal dumping ground for lead upto 5 km for all lifts, complete as per directions of Engineer-in-charge.

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth.

Supplying chemical emulsion in sealed containers including delivery as specified. Chlorpyriphos/ Lindane emulsifiable concentrate of 20%

Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti-termite treatment (excluding the cost of chemical emulsion) :Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1 cement : 2 Coarse sand) to match the existing floor: With Chlorpyriphos/Lindane E.C. 20% with 1% concentration

Supplying and stacking of hard stone (for stone pitching) 22.5 cm thick at site.

Dry stone pitching 22.5 cm thick laid in courses and required profile with hammer dressed stones having no side less than 15 cm, with minimum depth of 20 cm including preparing the bedding surface etc. all complete. (Payment for Stone to be made separately).

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 Cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size)

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate /retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement. All works upto plinth level. Concrete of M30 grade with minimum cement content of 350 kg /cum.

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate /retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement. All works above plinth level upto floor V level. Concrete of M30 grade with minimum cement content of 350 kg /cum.

Add for using extra cement in the items of design mix over and above the specified cement content therein.

Reinforced cement concrete work in arches, archribs, domes, vaults, shells, folded plate and roofs having slope more than 15° up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources).

Centering and shuttering including strutting, propping etc. and removal of form for all heights : Foundations, footings, bases of columns, etc. for mass concrete

Centering and shuttering including strutting, propping etc. and removal of form for all heights : Lintels, beams, plinth beams, girders, bressumers and cantilevers

Centering and shuttering including strutting, propping etc. and removal of form for all heights : Columns, Pillars, Piers, Abutments, Posts and Struts

Centering and shuttering including strutting, propping etc. and removal of form for all heights : Stairs, (excluding landings) except spiral-staircases

Centering and shuttering including strutting, propping etc. and removal of form for all heights : Weather shade, Chajjas, corbels etc., including edges

Centering and shuttering including strutting, propping etc. and removal of form for all heights : Suspended floors, roofs, landings, balconies and access platform

Centering and shuttering including strutting, propping etc. and removal of form for all heights : Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

Centering and shuttering including strutting, propping etc. and removal of form for all heights : Edges of slabs and breaks in floors and walls. Under 20 cm wide

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more.

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more.

Providing fusion bonded Epoxy coating not less than 175 micron thickness and upto 300 micron to reinforcement bars of any diameter as per IS-13620-1993/ ASTM-775 M including repairs to cut ends,welded spouts and handling damages with reccomended liquid epoxy compatible with the coating and testing of coating at plant etc complete as directed by engineer ion charge.

Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor etc., up to floor five level, excluding the cost of centering, shuttering and finishing: 1:5:10 (1 cement : 5 coarse sand (zone-III) : 10 graded stone aggregate 40 mm nominal size).

Cutting holes of required size in brick masonry wall for fixing of exhaust fan including providing and fixing 300 mm dia PVC pipe conforming BIS-12818 and making good the same etc. complete as per direction of Engineer-in-charge.

Close timbering over areas including strutting, shoring and packing cavities (wherever required) etc. complete. (Measurements to be taken of the face area timbered): Depth exceeding 1.5 m but not exceeding 3 m

Extra rates for quantities of earth works, executed: In or under water and/or liquid mud, including pumping out water as required Note for item no. 2.24:- The extra percentage rate is applicable in respect of each item but limited to quantities of work executed in these difficult conditions. The unit, namely, metre depth, to be considered for payment, shall be the depth measured from the sub soil water level up to the centre of gravity of the qty executed in difficult conditions. The depth shall be reckoned correct to 0.10 m, 0.05 m or more shall be taken as 0.10 m and less than 0.05 m ignored

Extra for laying concrete in or under water and/or liquid mud including cost of pumping or bailing out water and removing slush etc. completenThe quantity will be calculated by multiplying the depth measured from the sub-soil water level up to centre of gravity of concrete under sub-soil water level with quantity of concrete in cum executed under sub-soil water. The depth of centre of gravity shall be reckoned correct to 0.1m. 0.05m or more shall be taken as 0.1m and less than 0.05m ignored

Extra for laying reinforced cement concrete in or under water and/ or liquid mud, including cost of pumping or bailing out water and removing slush etc., complete. The quantity will be calculated by multiplying the depth measured from the subsoil water level up to the centre of gravity of the R.C.C. under subsoil water with the quantity of R.C.C. in cubic metre executed under subsoil water. The depth of centre of gravity shall be reckoned correct to 0.1 m. 0.05 m or more shall be taken as 0.1 m and less than 0.05 m ignored. No extra payment shall be made for placing reinforcement or centering & shuttering under sub - soil water conditions.

Extra for laying stone work in or under water and/or liquid mud including cost of pumping or bailing out water and removing slush etc. complete The quantity will be calculated by multiplying the depth measured from sub-soil water level up to the centre of gravity of stone work under sub - water with the quantity of stone work in cum executed under the sub-soil water. The depth of centre of gravity shall be reckoned correct to 0.1 m, 0.05 m or more shall be taken as 0.1 m and less than 0.05 m ignored.

Providing and laying autoclaved aerated cement blocks masonry with 150mm/ 230mm/300 mm thick AAC blocks in super structure above plinth level up to floor V level with RCC band at sill level and lintel level with approved block laying polymer modified adhesive mortar all complete as per direction of Engineer-in-Charge. (The payment of RCC band and reinforcement shall be made for seperately).

Providing and laying solid block masonry 10cm thick using best quality blocks of available size in cement mortar 1:4 ( 1cement: 4 coarse sand )for walls at any area (including duct walls,fin walls skin / ledge wall ,kerb wall etc) . The rate including cost, conveyance and unloading at site and stacking of all materials, all labour, scaffolding, watering, curing etc complete as per the direction of Engineer in charge.

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in :Cement mortar 1:4 (1 cement : 4 coarse sand)

Providing and fixing stainless steel(grade 316) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.)

12 mm cement plaster finished with a floating coat of neat cement of mix : 1:4 (1 cement: 4 fine sand)

15 mm cement plaster on the rough side of single or half brick wall of mix : : 1:4 (1 cement: 4 fine sand)

6 mm cement plaster of mix : 1:3 (1 cement : 3 fine sand)

Extra for plastering exterior walls of height more than 10 m from ground level for every additional height of 3 m or part thereof.

Prepare the surface and applying rough plaster on all internal RCC / Masonry surface, walls for toilets ,corridors etc in cement mortar 1:4 , 12 mm thick ,finished to line and plumb at all levels complete with necessary scaffolding, curing etc, complete including lead and lifts. Cost to include necessary scaffolding, staging, curing, leads and lifts etc., complete.

Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : 25 mm thick

Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete

Extra for pre finished nosing in treads of steps of Kota stone/ sand stone slab.

Extra for Kota stone/ sand stone in treads of steps and risers using single length up to 1.05 metre.

Providing and laying flamed finish Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge : Flamed finish granite stone slab Jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent.

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600x600 mm

Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. complete. Size of Tile 600x600 mm

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite of any colour and shade. Area of slab over 0.50 sqm

Extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform, vanity counter and similar location in marble/ Granite/ stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete.

Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. Granite work

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound ) content.With water thinnable cement primer on wall surface having VOC content less than 50 grams/litre

Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour. Two coats

Finishing walls with 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives. New work (Two or more coats applied @ 1.43 litre/ 10 sqm. Over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm.

Finishing walls with textured exterior paint of required shade : New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @ 2.20kg/10 sqm

Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to preparethe surface even and smooth complete.

Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : (a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours. (b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry.

Providing and applying fibre reinforced elastomeric liquid water proofing membrane with resilient acrylic polymers having Sun Reflectivity Index (SRI) of 105 on top of concrete roof in three coats @10.76 litre/ 10 sqm. One coat of self-priming of elastomeric waterproofing liquid (dilution with water in the ratio of 3:1) and two coats of undiluted elastomeric waterproofing liquid (dry film thickness of complete application/system not less than 500 microns). The operation shall be carried out after scrapping and properly cleaning the surface to remove loose particles with wire brushes, complete in all respect as per the direction of Engineer-in-Charge.

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : Two or more coats on new work

Providing and Fixing, uPVC factory-made, white colour casement Louvers made of extruded profiles. Profiles of frames and sash will be mitred cut and fusion-welded at all corners including drilling of holes for fixing hardware and drainage of water etc., making arrangements for fixing of hardware, EPDM gasket, 1.2 ± 0.2mm thick galvanised steel profile to be included in the required profile, the frame will be fixed to the wall with 8 mm x 100 mm long fasteners, all complete as per direction of Engineer-in-charge. The Rates inclusive of 6mm Glazing, Louvers, Locks, hardware hinges, handle and fitting etc.

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) :For fixed portion.Powder coated aluminium (minimum thickness of powder coating 50 micron)

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item):With float glass panes of 8 mm thickness (weight not less than 20 kg/sqm)

Providing and fixing 12 mm thick toughened glass panel of approved brand and manufacture, including making necessary arrangements for fixing required fittings, all complete as per direction of Engineer-in-charge

Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & double acting hydraulic floor spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-in-charge (Door handle, lock and stopper etc.to be paid separately).

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid door/window/Ceosetory windows & other Frames/Chowkhat comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modulus of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixed in position with M.S hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-In- Charge. (M.S hold fast/lugs or SS dash fasteners shall be paid for separately).Note: For WPC solid door/window frames, minus 5mm tolerance in dimensions i.e depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.Frame size 65 x 150 mm

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of required size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In- Charge. (Note: stainless steel butt hinges and necessary S.S screws shall be paid separately). 35 mm thick

Extra for providing vision panel not exceeding 0.1 sqm in all type of flush doors (cost of glass excluded) (overall area of door shutter to be measured):Rectangular or square

Providing and fixing factory made uPVC white colour sliding glazed window upto 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes, wire mesh and silicon sealent shall be paid separately). Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Three track three panels sliding window with fly proof SS wire mesh (Two nos. glazed & one no. wire mesh panels) made of (small series) frame 92 x 44 mm & sash 32 x 60 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension (Area of window upto 1.75 sqm).

Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick :Float glass panes. 4 mm thick glass pane (weight not less than 10kg/sqm).

Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick :Float glass panes.Fly proof stainless steel grade 304 wire gauge with 0.5 mm dia. wire and 1.4mm wide aperture with matching wood beading

Providing and fixing factory made uPVC white colour fixed glazed windows/ventilators comprising of uPVC multi-chambered frame and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), , uPVC extruded glazing beads of appropriate dimension, EPDM gasket, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes and silicon sealant shall be paid separately). Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. Fixed window / ventilator made of (small series) frame 47 x 50 mm & mullion 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension. (Area upto 0.75 sqm.)

Supply & laying of Frost/Privacy Film appoved design and color for All Glass Partitions and GLass doors. Rate including laying. (The successful manufacture should submit 10 years Warranty certicate to the clients. Product to be certified by Manufacturer's Representative)

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters:35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

Providing and fixing glazing in fire resistant door shutters, fixed panels & partitions etc., with G.I. beading made out of 1.6 mm thick G.I. sheet (zinc coating not less than 120 gm/m²) of size 20 x 33 mm screwed with M4 x 38 mm SS screws at distance 75 mm from the edges and 150 mm c/c, including applying a coat of approved fire resistant primer/powder coating of not less than 30 micron on G.I. beading, & special ceramic tape of 5 x 20 mm size etc complete in all respect as per NBC 2016, IS 16231 (Part 3):2016 and asper direction of Engineer-in-charge with glass of required thickness having 120 minutes of fire resistance both integrity & radiation control (EW120) and minimum 20 minutes of insulation (EI20). The manufacturer have to give test report/certification of fire glass and the glass should have the stamp showing the value of E, EW & EI. The glass shall be tested in approved NABL accredited lab or by any other accreditation body which operates in accordance with ISO/IEC 17011 and accredits labs as per ISO/IEC 17025 for testing and calibration scopes shall be eligible. The maximum glazing size shall not be more than 1100x2200 mm (w x h) or 2.42 sqm.

Providing and fixing fire resistant door frame of section 50 x 60 mm on horizontal side & 35 x 60 mm on vertical sides having built in rebate made out of 1.6 mm thick GI sheet ( Zinc coating not less than 120gm/m²) suitable for mounting 120 min Fire Rated Glazed Door Shutters. The frame shall be filled with Mineral wool Insulation having density min 96Kg/m³ . The frame will have a provision of G.I. Anchor fastners 14 nos ( 5 each on vertical style & 4 on horizontal style of size M10 x 80 ) suitable for fixing in the opening along with Factory made Template for SS Ball Bearing Hinges of Size 100x89x3mm for fixing of fire rated glazed shutter . The frame shall be finished with a approved fire resistant primer or Powder coating of not less than 30 micron in desired shade as per the directions of Engineer - in- charge . (Cost of SS ball bearing hinges is excluded).

Providing and fixing panic bar / latch (Double point) fitted with a single body, Trim Latch & Lock on back side of the Panic Latch of reputed brand and manufacture to be approved by the Engineer- in- charge, all complete.

Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISi, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete.

Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete.

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : 300x10 mm

Providing and fixing bright finished brass 100 mm mortice latch and lock, ISI marked, with six levers and a pair of anodised (anodic coating not less than grade AC 10 as per IS : 1868) aluminium lever handles of approved quality with necessary screws etc. complete.

Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embedding in cement concrete block 30x10x15cm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size).

Providing and fixing IS : 12817 marked stainless steel butt hinges with stainless steel screws etc. complete :100X58X1.90 mm

Providing and fixing GI grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete.

Providing and fixing sealing of shaft cutouts at all floor levels by using MS angle Iron frame around the shaft ms chequered plate of 6mm thick and pcc of 1:2:4 (100mm thick) on the plate for whole shaft area as per drawings and engineer-in -harge.Frame size should be minimum 100x50x6mm

Providing and laying tactile tile (for vision impaired persons as per standards) of size 300x300x9.8mm having with water absorption less than 0.5% and conforming to IS:15622 of approved make in all colours and shades in for outdoor floors such as footpath, court yard, multi modals location etc., laid on 20mm thick base of cement mortar 1:4 (1 cement : 4 coarse sand) in all shapes & patterns including grouting the joints with white cement mixed with matching pigments etc. complete as per direction of Engineer-in-Charge.

Providing and fixing removable raised/false access flooring with system and its components of approved make for different plenum height with possible height adjustment upto 50 mm, comprising of modular load bearing floor panels supported on G.I. rectangular stinger frame work and G.I. Pedestal etc. all complete, as per the architectural drawings, as specified and as directed by Engineer-in-charge consisting of: (a) Providing at required spacing to form modular framework, pedestals made out of GI tube of thickness minimum 2 mm and 25 mm outer diameter, fully welded on to the G.I. Base plate of size 100mm x 100mm x 3mm at the bottom of the pedestal tube, G.I. pedestal head of size 75mmx75mmx3.5 mm welded with GI fully threaded stud 16mm outer diameter with two GI Check nuts screwed on the stud for level adjustment upto 50mm, locking and stabilizing the pedestal head in position at the required level. The pedestals shall be fixed to the subfloor (base) through base plate using epoxy based adhesive of approved make or the machine screw with rawl plug. (b) Stringers system in all steel construction hot dipped galvanized of rectangular size 570x20x30x0.80mm thick having holes at both ends for securing the stringers on to the pedestal head using fully threaded screws ensuring maximum lateral stability in all directions, the grid formed by the pedestal and stringer assembly shall receive the floor panel, this system shall provide adequate solid, rigid support for access floor panel, the system shall provide a minimum clear uninterrupted clearance between the bottom of the floor for electrical conduits and wiring etc. all complete as per the architectural drawings, as specified and as directed by the Engineer-in-charge. (c) Providing and fixing Access Floor panel of 600x600x32 mm medium grade Filled Steel anti static high pressure Lamination of 800H grade (FS800H). Access Floor panel shall be steel welded construction with an enclosed bottom pan with uniform pattern of 64 hemispherical cones. The top and bottom plates of Steel Gauges: top 0.6 mm and bottom 0.7 mm fused spot welded together (minimum 64 welds in each dome and 20 welds along each flange). The panel should be Corroresist epoxy coated for lifetime rust protection and cavity formed by the top and bottom plate is filled with Pyrogrip noncombustible Portland cementitious core mixed with lightweight foaming compound. The access floor shall be factory finished with Anti-static High Pressure laminate with Non Warp technology upto 1mm thickness for superior adhesion and Surface flatness within 0.75mm.The panel is to withstand a Concentrated Load of 363 kgs applied on area 25mm x 25mm without collapse in the centre of the panel which is placed on four steel blocks. The panel will withstand and Uniformly Distributed Load (UDL) minimum 1250 kg/sqm and an impact load of 50kg all complete as per the approved manufacturers specification and as per the direction of Engineer-in-charge. All specification must be printed on the side of the panel to ensure the quality of the product. 300 mm Finished Floor Height (FFH)

Designing, fabricating, testing, installing and fixing in position Curtain Wall with Aluminium Composite Panel Cladding, with open grooves for linear as well as curvilinear portions of the building , for all heights and all levels etc. including: a) Structural analysis & design and preparation of shop drawings for pressure equalisation or rain screen principle as required, proper drainage of water to make it watertight including checking of all the structural and functional design. b) Providing, fabricating and supplying and fixing panels of aluminium composite panel cladding in pan shape in metalic colour of approved shades made out of 4mm thick aluminium composite panel material consisting of 3mm thick FR grade mineral core sandwiched between two Alumini um sheets (each0.5mm thick). The aluminium composite panel cladding sheet shall be coil coated, with Kynar 500based PVDF / Lumiflon based fluoropolymer resin coating of approved colour and shade on face # 1 and polymer (Service) coating on face # 2 as specified using stainless steel screws, nuts, bolts, washers, cleats, weather silicone sealant, backer rods etc. c) The fastening brackets of Aluminium alloy 6005 T5 / MS with Hot Dip Galvanised with serrations and serrated washers to arrest the wind load movement, fasteners, SS 316 Pins and anchor bolts of approved make in SS 316, Nylon separators to prevent bi-metallic contacts all complete required to perform as per specification and drawing The item includes cost of all material & labour component, the cost of all mock ups at site, cost of all samples of the individual components for testing in an approved laboratory, field tests on the assembled working curtain wall with aluminium composite panel cladding, cleaning and protection of the curtain wall with aluminium composite panel cladding till the handing over of the building for occupation. Base frame work for ACP cladding is payable under the relevant aluminium item.s The Contractor shall provide curtain wall with aluminium composite panel cladding, having all the performance characteristics all complete , as per the Architectural drawings, as per item description, as specified, as per the approved shop drawings and as directed by the Engineer-in-Charge. However, for the purpose of payment, only the actual area on the external face of the curtain wall with Aluminum Composite Panel Cladding (including width of groove) shall be measured in sqm. up to two decimal places

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.

Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer's specifications including appropriate priming coat, preparation of surface, etc. complete. On steel work

Providing orange colour safety foot rest of minimum 6 mm thick plastic encapsulated as per IS : 10910, on 12 mm dia steel bar conforming to IS: 1786, having minimum cross section as 23 mmx25 mm and over all minimum length 263 mm and width as 165 mm with minimum 112 mm space between protruded legs having 2 mm tread on top surface by ribbing or chequering besides necessary and adequate anchoring projections on tail length on 138 mm as per standard drawing and suitable to with stand the bend test and chemical resistance test as per specifications and having manufacture's permanent identification mark to be visible even after fixing, including fixing in manholes with 30x20x15 cm cement concrete block 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) complete as per design.

Providing & fixing Poly carbonate multi wall plain sheet 8 mm thick as approved by the Engineer in charge and should be supplied in a single length of 12 M or as decide by the Engineer in charge. The sheets shall be fixed using self drilling/ self tapping screw of size ( 5.5x55mm) with EPDM seal complete upto any pitch in horizontal /vertical / curved surface, but excluding the cost of purlins, rafters, trusses, and including cutting to size and shapes where ever required.

Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt/ suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality.

Providing and Fixing of Building signages as per following specifications - Sign to be made shall be made of 3 mm aluminium / Acrylic Box Letters (100mm thick letters). Sign Face shall be in 3mm 0/40 Translucent Acrylic with Male / 10mm Water Proof Sun board Female Joint Adequate LED of Samsung Make shall be fitted with the required wiring & Waterproof Transformer to have the uniform Light. A provision for Weather Proof Box shall be made to keep the Transformers. The signages to be fixed on the structural ACP + MS framework with required sizes as per the design. The item includes design of supporting arrangement, fabrication, installation and commissioning the signages with structural framing including channels, angles, gusset plates and anchoring the frame by anchor fasteners to the Building. The structural framing should be painted with primer and enamel paints

Frosted Film - Supply & laying of Frost/Privacy Film approved design and colour for All Glass Partitions and Glass doors. Rate including laying. (The successful vendor should submit 10 years Warranty certicate to the clients. Product to be certified by Manufacturer's Representative)

Supply and fixing of Floor indication/ Fire exit/ Staircase/ Room indication signages of size 300mm x 150mm x 5mm or nearest size either hanged on ceilings/ fixed on walls with LED unit of approved make. The signage should be made up of acrylic material or fire resistant material on ACP. The signage should include a built-in UPS backup. It should be affixed to the existing background using appropriate chains and hooks, all complete as per the architectural design.

Providing and fixing Gypsum false ceiling (12.5 mm) at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with : 12.5 mm thick tapered edge gypsum moisture resistant board

Providing & fixing 8 mm thick Calcium Silicate false ceiling at all height including providing & fixing of framework made of special section, power pressed from M.S. sheets and galvanised with zinc coating of 120 gms/ sqm (both side inclusive) as per IS : 277 and consisting of angle cleat of size 25mm wide x 1.6mm thick with flanges of 27mm and 37mm, at 1200mm c/c, one flange fixed to the ceiling with dash fastener 12.5mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25 x10 x0.50mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I chanels 45 x15 x 0.90mm running at the spacing of 1200 mm c/c, to which the ceiling section 0.5mm thick bottom wedge of 80mm with tapered flanges of 26 mm each having lips of 10.5mm, at 450mm c/c, shall be fixed in a direction perpendicular to G.I intermediate channel with connecting clip made out of 2.64mm dia x 230mm long G.I wire at every junction, including fixing perimeter channels 0.50mm thick 27mm high having flanges of 20mm and 30mm long, the perimeter of ceiling fixed to wall/ partitions with the help of Rawl plugs at 450mm centre, with 25mm long dry wall screws @ 230mm interval, including fixing of Calcium Silicate Board to ceiling section and perimeter channels with the help of dry wall screws of size 3.5 x25mm at 230mm c/c, including jointing & finishing to a flush finish of tapered and square edges of the board with recommended jointing compounds, jointing tapes,finishing with jointing compounds in three layers covering up to 150mm on both sides of joints and two coats of primer suitable for boards, all as per manufacture's specification and also including the cost of making opening for light fittings, grills, diffusers, cut outs made with frame of perimeter channels suitably fixed, all complete as per drawings, specificaton and direction of the Engineer in charge but excluding the cost of painting with: 8 mm thick Calcium Silicate Board made with Calcareous & Siliceous materials reinforced with cellulose fiber manufactured through autoclaving process.

Providing and fixing tiled false ceiling of specified materials of size 595x595 mm in true horizontal level,suspended on inter locking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 grams/ sqm, both side inclusive) consisting of main "T" runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross "T" of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main "T" at 600 mm center to center to form a grid of 1200x600 mm and secondary cross "T" of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main "T" runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyesterpaint, all complete for all heights as per specifications, drawings and as directed by Engineer-in-charge. GI Metal Ceiling Lay in plain Tegular edge Global white color tiles of size 595x595 mm, and 0.5 mm thick with 8 mm drop; made of G I sheet having galvanizing of 100 gms/sqm (both sides inclusive) and electro statically polyester powder coated of thickness 60 microns (minimum), including factory painted after bending.

Providing and fixing wooden ceiling made up of 12mm tk Plywood confirming IS 710 with laminate finish,including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting.

Providing and fixing of celing pelmet using high-quality plywood with a minimum thickness of 19mm with 1mm laminate.The edges of the plywood are finished with matching edge banding , including brackets, screws, or other suitable hardware for the installation requirement, all complete as per approved design and 3D.

Supply and Installation of Proprietary make modular access Trap door for following sizes, shutter & door frame shall be made in stable aluminum frame work, the shutter shall be cladded with 12.5mm thick gypsum board all as per manufactures specification adhering to the detailed drawings. The shutter shall be finally finished with plastic emulsion paint of approved shade & make as directed by the Architects.Size-600x600mm

Providing and fixing 450mm wide Pantry unit made with 710 grade prelaminated plywood in approved wooden laminate shade on shutters and all visible areas. Best quality telescopic sliders,hinges,locks,hardware to be provided. (HETTICH/DORMA/HAFELE OR EQ) as per drawing and 3D.counter top laid with steel grey granite with bullnose rounded edge .

Providing & fixing TV unit ledge of 30mm thick with back panelling in lobby made with 16mm plywood box work with all visisble area in laminate finish 1MM MERRINO 10510 MAGUS WALNUT BRONZE and 3mm groove at 60cm intervals as per 3D and drawing.

Providing ,supplying & fitting of vanity counters/ wash basin counters with cabinets of carcase with 19mm tk BWP 710 grade plywood with laminate finish &wooden edge band,16mm tk BWP 710grade pywood shutters with self closing hinges. counter top with granite or fullbody tile laid over 8 mm thick multiwood board, with cement based high polymer modified quick set adhesive (water based) conforming to IS : 15477, in average 6 mm thickness, joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete all as directed by the Architect.Extra for providing opening of required size & shape for wash basin, vanity counter and similar location in granite or fullbody tile ,including necessary holes for pillar taps etc.Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer's specifications including appropriate priming coat, preparation of surface, etc. on complete steel work

Providing & supplying of Mirror fixing in toilet, above Toilet wash counter to provide 6mm edge polished mirror fixed with mirror stud.

Providing and fixing wardrobes and cabinet with 16mm thick Marine plywood box work with inside area approved 1 mm thick frosty white laminate, shutter with 19mm Plywood with 1mm thick GREENLAM 930 SGL GLISTEN on all visible areas. Best quality telescopic sliders,hinges,locks,hardware to be provided. (HETTICH/DORMA/HAFELE OR EQ) as per drawing and 3D

Providing and fixing registration,pharmacy and admin counters with 16mm and 12mm thick marine plywood with approved shade 1mm thick laminate ( GREENLAM GLISTEN 930SGL) on all visible areas. Internal laminate finish in white. Table to have CPU stand,key board tray, wire manager, footrest, 3 drawers with multi latch locks,telescopic sliders and all required soft close hardware. Top covered with 19mm edge bullnose Black granite as per drawing.

Providing and fixing coffee shop bottom counter, overhead cabinets made with 16mm marine plywood box work with inside area approved laminate FROSTY WHITE MATT ( MERRION/GREENLAM or equivalent) and shutter made 19mm plywood with 1mm approved Laminate SIBERIAN PIKE OAK 10839(MERRINO or equivalent )shade fixing on visible areas . Outer elevation to be covered with White Brick pattern texture over Plywood boxing as per 3D .Counter top covered with 19mm edge bullhead shaped Jet Black Granite and best quality Hettich/Hafele brand sliders, hinges, soft close drawer channels,lock fixing and work as per architects

Providing & fixing Teapoy of 900x450mm and Glass should be 12 ±0.3 mm toughened glass uv glued with bushes made in ss 202 grade for fixing with under structure. it should be a welded assembly made in ss202 grade having dia 12mm.

Providing & fixing Teapoy of 400mm dia and Glass should be 12 ±0.3 mm toughened glass uv glued with bushes made in ss 202 grade for fixing with under structure. it should be a welded assembly made in ss202 grade having dia 12mm.

Providing & fixing 3 seater sofa with dimension -2400 mm Width x 950 mm Depth x 950 mm Height.Frame shall be made of combination of 12 mm moisture resistance and termite free plywood and pine wood (without knot)having cross section 34x64mm.Seat - shall be made of slab stock foam of density of base 28 kg/ meter cube and super soft 32 kg/meter cube at top. Seatshall be embeded with 2mm pocket spring.Seat Back - made of slab stock foam of density 28 kg/ meter cube pasted on back. Front of the back rest shall be made ofloose conjugated polyester fiber webbing.Legs - legs shall be made of rubber wood.Facia - facia of the sofa shall be made of membrane pressed MDF.

Providing & fixing 2 seater sofa with dimension -1800 mm Width x 950 mm Depth x 950 mm Height.Frame shall be made of combination of 12 mm moisture resistance and termite free plywood and pine wood (without knot)having cross section 34x64mm.Seat - shall be made of slab stock foam of density of base 28 kg/ meter cube and super soft 32 kg/meter cube at top. Seatshall be embeded with 2mm pocket spring.Seat Back - made of slab stock foam of density 28 kg/ meter cube pasted on back. Front of the back rest shall be made ofloose conjugated polyester fiber webbing.Legs - legs shall be made of rubber wood.Facia - facia of the sofa shall be made of membrane pressed MDF.

Providing & placing three seater waiting chair. CROSS BEAM: It should be made up of black powder coated rectangularM.S.ERW tube having 8.0 ± 0.03 cm x 4.0 ± 0.03 cm x 0.2 ± 0.014 cm size.LEG AND ARMREST: It should be chrome plated made of cold rolled steel with 0.12 ± 0.013 cm thinkness.SEAT/BACK SHELL: It should be powder-coated perforated shell made from cold rolled M.S. sheet.The Side Bar should be made of Chrome plated solid steel 3.0 ± 0.03 cm x 1.2 ± 0.3 cm with fluting and plastic inserts. The Shell should be assembled on the Cross Beam with help of M8 Bolts .Overall Dimensions:Seat Height - 40.0cm, Height - 67.5 cm, Width & Depth of Chair as - Width-163.0cm and Depth-57.0 cm

Providing and fixing conference table of size 4200 mm width x 1200 mm depth. Legs shall be made from 25 mm PPB having a straight profile with half round edges and clad with 0.6 mm thick post forming laminat. Overall thickness of leg shall be 26.2 mm.Modesty panel of understructure shall be made of 18 mm thick Pre laminated Twin Board.

Providing & fixing conference and admin chair. SEAT/BACK ASSEMBLY: The seat should be made up of 1.2 ± 0.1cm. thick hotpressed plywood and upholstered with leather and moulded Polyurethane Foam. The back foam should be designed withcontoured lumber support for extra comfort. BACK SIZE: 53.0cm.(W) X 95.4cm.(H) SEAT SIZE: 54.6cm.(W) X 49.0cm.(D) HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HRpolyurethane foam should be moulded with density = 45 +/-2 kg/m³ and Hardness load 16 ± 2 kgf for 25% compression.SEAT-BACK CONNECTING SPINE:The seat and back should be arrested together with spine made of 0.8 ±0.05 cm thkHR Steel and should be black powder-coated ( DFT 40-60 microns ).ARMREST ASSY: The armrest assy. should comprise of three parts viz. the armrest support tube and P.U. armrest and thearmrest top. The armrest tube assy. should be made of 2.54±0.03cm x 0.16±0.0128cm M.S. E.R.W. support tubes andChrome plated. The P.U. armrest should be made of black integral skin polyurethane with 50-70 shore 'A' Hardness andreinforced with M.S. insert. The armrest top should be made of ABS & upholstered with foam & leather. FRONT PIVOT SYNCHRO TILT MECH.: The mechanism should be designed with the following features:•360° revolving type.•Seat back tilting ratio of 1 : 1.5•Front pivot for tilt with feet resting on ground ensuring more comfort.•Tilt tension adjustment.•5-position locking with anti-shock back mechanism, which prevents the backrest from impacting the user when the lockshould be released.•Static seat depth adjustment = 5.0 ± 0.5cm with 5 position locking.PNEUMATIC HEIGHT ADJUSTMENT: it has an adjustment stroke of 9.0 ± 0.3cm.BLOW MOULDED BELLOW : The bellow should be 1 piece and blow moulded in black Polypropylene.PEDESTAL ASSY: The pedestal should be made of die-cast aluminium with buffing finish. It should be fitted with 5nos. twinwheel castor. The pedestal should be 67.0 ± 0.5cm pitch-center dia. (77.0 ± 1.0cm with castors).TWIN WHEEL CASTORS: The twin wheel castors should be injection moulded in black Nylon.

Providing & fixing examination chair. SEAT/BACK ASSEMBLY: The seat and back should be made up of 1.2 ±0.1cm, thick hotpressed plywood, upholstered with fabric and moulded Polyurethane foam with PVC lipping all around. The back foamshould be designed with contoured lumbar support for extra comfort.POLYURETHANE FOAM: The polyurethane foam should be moulded with density = 45 ±2 kg/m' and Hardness = 20 ±2 onHampden machine at 25% compression.TUBULAR FRAME: The tubular frame should be cantilever type & made of 0 2.54 ±0.03cm. x 0.2 +0.016cm. M.S. E.R.W.tube and black powder coated ( DFT 40-60 microns ).The Armrest Tube of 0 2.54 +0.03cm. x 0.2 ±0.016cm. M.S. E.R.W.tube should be welded to mainframe. The desklet should be fitted on the right hand side.DESKLET ASSEMBLY: The wooden desklet should be made of 1.8 ±0.05cm. thk. pre-laminated particleboard with 0.15±0.03cm. thk. P.V.0 lipping all around.ARMRESTS: The one-piece armrests should be made of black integral skin polyurethane foam with 50-70 Shore hardnessand reinforced with M.S. insert. The armrests should be scratch and weather resistant tant.PAPER TRAY: The paper tray should be made of 0 0.4 +01-0.005cm. M.S. wire spot welded to form a mesh. It should beblack powder coated.

Providing and fixing Nurses station Table with 16mm and 12 mm thick marine plywood with 1mm thick Laminate finish (GREENLAM 930 SGL GLISTEN) on visible areas. Bottom portion covered in Wooden laminate shade (MERRINO-10510 MAGUS WALNUT BRONZE) and steel skirting as per 3D image and drawing. Top and sides covered with 12mm CORIAN (LG- HI-MACS W007 LENTIL) eased edge. Internal finish with laminate in 0.8mm Frosty white matt as per drawing and 3D images.

Providing & fixing consultation table with written of 1500x750 mm H. Primary Work Surface shall be Made of25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to topSoft closing access flap with in-build power box are provided on work surface for wire management.Secondary Work Surface of the green guard by ul certified table shall be made of 25mm thick MDF one side pre-laminateboard confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top.Modesty Panel Made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVCmembrane pressed on to top. There shall be a desk pad of width 800 mm and depth 430 mm made of 1 mm thich artificialleather glued on 1.2 mm thick GI sheet a per IS 277.Under structure Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS12823:1990, Edge banded with matching 2 mm thick PVC lipping.Integrated Pedestal Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS12823:1990, Edge banded with matching 2 mm thick PVC lipping.Drawer fronts made of 25mm thick MDF one side pre-laminate board confirming toIS-14587:1998 with 0.4mm PVC membrane pressed on to top Pedestal construction is BOX-BOX-FILE type which Usespowder coated 400 MM long metal Panel Drawer Slides. Drawer extension is 325 MM.Drawers have a soft closing & anti slam mechanism.Handles are provided for ease of opening.Pedestals are provided with lock for security.

Providing and supplying High back chair. SEAT/BACK A SSEMBLY: The seat is made up of 1.2 + 0.1cm thk. hot pressed plywoodmeasured as per QA method described in OCP-QLTA-PL14-18.The Back is made up of injection mou1ded glass filled nylon& upholstered using Mesh fabric with high tenacity yarn.HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane seat foam is moulded with density 45+/-2 kg/m°and hardness 16 + 2 kgf as per IS:7888 for 25% compression.ARMRESTS : The adjustable armrest is designed with Up-Down adjustment— 8 steps (8 0+0.Scm range) Height adjustable armrest structure which is Powder Coated & fitted with an armrest top. Fixed Armrest Top is PU moulded over metal insert.LUMBAR SUPPORT ASSEMBLY: The Lumbar support consists of polypropylene pad with moulded polyurethane foam &covered with polyester fabric.The Height of Lumbar pad can be adjusted through two projecting knobs provided on the rearside of the pa6. Lumbar pad has an adjustment of 8.0 + 0.5 cm in height.FRONT PIVOT SYNCHRO MECHANISM: The adjustable tilting mechanism is designedwith the following features. 360° revolving type.Single point control. Front-pivot for tilt with feet resting on ground ensuring more comfort. Tilt tension adjustment.4-position locking with anti-shock feature.Seat/back tilting ratio of 1:2.NECKREST : The Neckrest assembly consist of polypropylene pad with moulded polyurethane foam & covered withpolyester fabric Neckrest is fixed to Back Assembly through Neckrest connector Neckrest assembly has height adjustment.

Providing and fixing visitors chair,The seat and back are made of injection moulded high impact strenght polypropylene polymer compound with indoor grade UV Resistance.The tubular weled frame is made from Dia2.22 +/- 0.03cmx 0.12+/- 0.0128 cm and 3.5+/- 0.03 cm x 0.12+/-0.0128 cm stainless Steel 202 grade tube.The tube of green guard by ul certified chair shall be buffed polished to give shinyfinish. The Shoes are made of high impact strenght polypropylene polymer compond with indoor grad UV Resistance andpressed fitted with tubularfram.

Supply & fixing of patients Steel Stools with cushions, size 21"ht 14" dia cushion fabric top and stool legs of 1" dia SS tube

Supply & fixing dining table 130x300cm 4 seater capacity , made up of plywood confirming to IS 710 with PU Coating . The table top shall be provided with 1 mm thk laminate.Legs are made up of harwood/Ashwood. All exposed faces finished with PU polish for wood frames .

Providing & fixing dinning table of 90cm dia 3 Seater,made up of plywood confirming to IS 710 with PU Coating . The table top shall be provided with 1 mm thk laminate.Legs are made up of harwood/Ashwood. All exposed faces finished with PU polish for wood frames .

Providing & fixing Study table with prelaminated plywood confirming IS 710 grade 16mm ,with 1mm thick laminated fixing on drawer shutters and all visible areas.Best quality accessories and telescopic sliders for drawers to be used(HETTICH/DORMA OR EQ) (TABLE SIZE: 900MMX50MMX75MM, DRAWER SIZE: 300MMX150MM[H])

Providing and fixing of linear workstation Table top 1200x600x750mm of 25mm thick Pre-laminate particle board E1 norms finished with 2mm pvc edge banding on all expossed edges.Under-structure : Supported on MS powdercoated CONNECT leg with supporting beams.Wire management : 65mm Dia grommet and Below Table Top 250 mm ht laminate fascia.Raceway &separator for power & data cable management. MS vertical cover for wire entry.

Providing & supplying Bystander Cot made with hardwood frame work and plywood box work covered with laminate of approved shade.Head Board made with 12mm plywood fixing at 16mm plywood box work with laminate in approved color on all visible areas. Accessories and hardware,6 inches foam/coir mattress of approved brand (customised dimension to fit cot) to be provided as per approved architects drawing.

Stone tile (polished) work for wall lining over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and cement slurry @ 3.3 kg/sqm including pointing in white cement complete.8mm thick.Granite of any colour and shade

Providing and fixing of wall panelling with 19 mm thick 710 BWP fire retardant plywood conforming to IS: 5509 /10701 grade internal frame work over which 12 mm thick 710 BWP fire retardant plywood is fixed on. Exposed area finishing with 12.5mm thick gypsum board , as per design approved by Architects.

Providing and installation of Acoustic wall panelling with 12mm pet panels of size: 1220x2440 of weight 1800 g/m2, which are 50 % recyclable material has LEED MR-4, having NRC value upto 0.8 and 15 mm Wood Fiber of size: 600x1200mm of density 410 kg/m3, with Green (VoC,RC%)-Low 10, having NRC value upto 0.9,with polyester fibre infill of 500GSM. Fixed with GI struts of Web Width 48mm, depth 48mm, 0.6mm thickness are used to form frame from ceiling to floor of CC – 600mm framing on both the planar sides from (Vertical & Horizontal). Above this framing, one side first layer will be gypsum board of 12mm thick and second layer will be 15 mm wood wool board and another side will two layer of 12 mm thick gypsum board of approved make. Wood wool boards, pet panels and gypsum boards are installed using black phosphate or nickel pated bugle head fine threaded screws horizontally or vertically as per the architecture design and infill is used to fill the gap between the frames. The rates for above works are inclusive of all cost materials incluidng fabric, fabrication charges, transportation and installation, labour, etc complete, as per design approved by Architects.

Providing and fixing of wallpaper with paper backing with 220-250 GSM. The wallpapers are printed on either low VOC, or PVC-free LEED-certified substrates- either of which are intended for a range of commericial applications. These are fixed with Bartoline or equivalent-all purpose wallpaper adhesive with high quality and which is easy to mix. As per design approved by Architects.

Finishing walls with textured interior paint of required shade: New work (Two or more coats applied @ 3.28 ltr/ 10 sqm ) over and including priming coat of exterior primer applied @ 2.20 kg/ 10 sqm

Supplying and installation of Black out roman blinds as per the detailed Technical specification and deatiled drawing. Including all fixing charges and necessary fittings. Base rate of fabric is Rs. 700/-

Supplying and installation of Black out roller blinds as per the detailed Technical specification and deatiled drawing. Including all fixing charges and necessary fittings. Base rate of fabric is Rs. 700/-

Supplying and fixing of Main curtain (Size:345X220 cm), with polyester based cotton blend pleated curtains. Including all fixing charges and necessary fittings.

Providing and fixing Cubicle curtains made by 2400 square inch treads,100% Polyester Fabric,Fungus Retardent, Water repellant,Stain retardent,and easy washable.Curtains gsm 175to180 gsm.

Providing and fixing CubicleTracks made of AlluminumAlloy of Box size 1.7x20x25mm with 50-60 microns powder coating in white color.Tracks are bend to a radius at 90 degree.Wall Bracket:Made of CRC steel with white powder coating finish. Bridge Clamp:Made of CRC steel with white powder coating finish.RoofSuspension:Made of aluminum pipe of 12.5mm &20mm diameter.The upper circular plate made of aluminum with 50.4mm diameter thickness.Curtain Removal Point is Made of SS.Runner: Comprises of Wheel type runners made of Teflon ISS material for easy and smooth sliding of curtain.

Providing and fixing corridor handrails cum wall guard of 4" dia complete with continuous aluminum retainer and vinyl cover . Complete with mouting brackets, end returns and fixing accessories. Fixed at 1000mm (upto centre) from finished floor level.

Providing and fixing 52mmx52mm corner guard complete with continuous aluminum retainer and vinyl cover. Complete with top caps,end returns and all fixing accessories.Fixed on walls above skirting

Providing and fixing rigid pvc sheet 1mm sheet for wall protection, complete with top caps and silicon filling for joints.( To be used as kick plates on doors - size 4'x2').

Providing and fixing ABS plastic, anti-rust, easy to clean bed side lockers. Including one drawer and equiped with a door wth glass holder, towel shelf on two sides with castor(2 with brake). Size:48x48x81cm.

Providing and fixing locker cabinets and drawers made from MS CRCA sheet, stainless steel top with raised edge on 3 sides, castors 2 with brakes, pre treated powder coated finish.

Providing and fixing over bed table, frame made of rectangular square tube with body section mounted on 5 cm castors, with laminated top of 75cmx 40cm with height adjustable gear handles.

Providing and fixing foam mattress comes in 4 sections. It is covered with rexin closed with zip at one end. It is used on full fowler bed. Product size:190x90x10

Providing & supplying Patients Cot 36" wide x 80" length ,made of combination of mettallic and plastic,finishing by Pretreated and Epoxy Powder Coated.Provided by adjustable height for the entire bed, the head, and the feet, adjustable side rails, and electronic buttons to operate both the bed and other nearby electronic devices and are mounted on wheels allowing for mobility. Including soft furnishing items,necessary fittings and fixing charges.

Providing & supplying ICU bed (200x90x60cm) made up of Frame work of M.S. Tube ,Pair of Foldable Aluminum Side Rails, head and foot board. Four section top made up of perforated MS Sheet. provided with 2 brakes and holder for Urine bag.finished with pretreated & Epoxy Powder Coated/ Baked Paint and Five Function available with manual operation Functions are Head End Elevation, Foot End Elevation, Hi-Low, Trendelenburg, Reverse Trendelenburg. Including soft furnishing items,necessary fittings and fixing charges.

Providing & supplying Labour room bed (200x90x60cm) single size bed made up of Frame work of M.S. Tube ,Four section top made up of perforated MS Sheet,Pair of Foldable Aluminum Side Rails,head and Foot Panel.Provided with holder for Urine bag,Backrest elevation,Knee rest elevation,High/Low movement and Provision for I.V. Rod at all corners. Including soft furnishing items,necessary fittings and fixing charges.

Providing and fixing examination couch with cabinets . Body section covered with sheet for 3 sides . It comes with three drawers & three cabinet. It has 2 section coushioned top. It has adjustable backrest by gas spring system.Ithas inbuilt foot step for patients. Product size: 183L X 50W X 82 H

Providing & supplying manually operated SNCU beds 180x150x13cm ,made up of frame work of rectangular M.S Tube and 2 Section top made of perforated M.S Sheet,having head & foot Panels. finished with pre treated and Epoxy powder Coated. Including soft furnishing items,necessary fittings and fixing charges.

Providing and supplying hospital trolley of 1.5 to 2.5 ft height,made up of MS material finished with color coated, provided wityh 4 wheels.

Procuring healthy grass free from weeds and foreign materials and laying on the soil medium as turfing,the rate include for grass cost, transport to site, cost and application of manure, planting, labour, supervision and maintenance for 2 months after planting Pearl Grass

Procuring and planting specified nursery grown trees, shrubs and other plants .Rates include plant cost,transport, cost of manure, planting, labour,supervision and maintenance for 2 months after planting. Royal palm

Procuring and planting specified nursery grown trees, shrubs and other plants .Rates include plant cost,transport, cost of manure, planting, labour,supervision and maintenance for 2 months after planting. Foxtail palm

Procuring and planting specified nursery grown trees, shrubs and other plants .Rates include plant cost,transport, cost of manure, planting, labour,supervision and maintenance for 2 months after planting. Bismarkia palm

Procuring and planting specified nursery grown trees, shrubs and other plants .Rates include plant cost,transport, cost of manure, planting, labour,supervision and maintenance for 2 months after planting. Jackfruit tree

Procuring and planting specified nursery grown trees, shrubs and other plants .Rates include plant cost,transport, cost of manure, planting, labour,supervision and maintenance for 2 months after planting. Elenji tree

Procuring and planting specified nursery grown trees, shrubs and other plants .Rates include plant cost,transport, cost of manure, planting, labour,supervision and maintenance for 2 months after planting. Coconut tree

Procuring and planting specified nursery grown trees, shrubs and other plants .Rates include plant cost,transport, cost of manure, planting, labour,supervision and maintenance for 2 months after planting. Malpighia Topiary in steel mesh

Procuring and planting specified nursery grown trees, shrubs and other plants .Rates include plant cost,transport, cost of manure, planting, labour,supervision and maintenance for 2 months after planting. Eugenia Topiary

Procuring and planting specified nursery grown trees, shrubs and other plants .Rates include plant cost,transport, cost of manure, planting, labour,supervision and maintenance for 2 months after planting. Clerodendrum Inerme -Hedge

Procuring and planting specified nursery grown trees, shrubs and other plants .Rates include plant cost,transport, cost of manure, planting, labour,supervision and maintenance for 2 months after planting. Murraya Exotica - Flower bush

Procuring and planting specified nursery grown trees, shrubs and other plants .Rates include plant cost,transport, cost of manure, planting, labour,supervision and maintenance for 2 months after planting. Heliconia Caribea

Procuring and planting specified nursery grown trees, shrubs and other plants .Rates include plant cost,transport, cost of manure, planting, labour,supervision and maintenance for 2 months after planting. Areca tree

Supplying , stacking and spreading sludge / well decayed farm yard manure from thesource,Mixing earth and manure or in proportion specified or directed, Spreading of dung manure or / and good earth in required thickness. and fine dressing the ground as per natural gradiantapproved by the engineer in charge incl. screening, loading, unloading, conveyance and stacking at site.

Close timbering in case of shafts, wells, cesspits, manholes and the like including strutting, shoring and packing cavities (wherever required) etc. complete. (Measurements to be taken of the face area timbered). Depth exceeding 1.5 m but not exceeding 3 m

Providing and applying integral crystalline slurry of hydrophilic in nature for waterproofing treatment to the RCC structures like retaining walls of the basement, water tanks, roof slabs, podiums, reservior, sewage & water treatment plant, tunnels / subway and bridge deck etc., prepared by mixing in the ratio of 5 : 2 (5 parts integral crystalline slurry : 2 parts water) for vertical surfaces and 3 : 1 (3 parts integral crystalline slurry : 1 part water) for horizontal surfaces and applying the same from negative (internal) side with the help of synthetic fiber brush. The material shall meet the requirements as specified in ACI-212-3R-2010 i.e by reducing permeability of concrete by more than 90% compared with control concrete as per DIN 1048 and resistant to 16 bar hydrostatic pressure on negative side. The crystalline slurry shall be capable of self-healing of cracks up to a width of 0.50mm. The work shall be carried out all complete as per specification and the direction of the engineer?in-charge. The product performance shall carry guarantee for 10 years against any leakage. For vertical surface two coats @0.70 kg per sqm

Providing and applying integral crystalline slurry of hydrophilic in nature for waterproofing treatment to the RCC structures like retaining walls of the basement, water tanks, roof slabs, podiums, reservior, sewage & water treatment plant, tunnels / subway and bridge deck etc., prepared by mixing in the ratio of 5 : 2 (5 parts integral crystalline slurry : 2 parts water) for vertical surfaces and 3 : 1 (3 parts integral crystalline slurry : 1 part water) for horizontal surfaces and applying the same from negative (internal) side with the help of synthetic fiber brush. The material shall meet the requirements as specified in ACI-212-3R-2010 i.e by reducing permeability of concrete by more than 90% compared with control concrete as per DIN 1048 and resistant to 16 bar hydrostatic pressure on negative side. The crystalline slurry shall be capable of self-healing of cracks up to a width of 0.50mm. The work shall be carried out all complete as per specification and the direction of the engineer?in-charge. The product performance shall carry guarantee for 10 years against any leakage. For horizontal surface one coat @1.10 kg per sqm.

Providing and Placing in position suitable PVC water stops conforming to IS:12200 for construction/ expansion joints between two RCC members and fixed to the reinforcement with binding wire before pouring concrete etc. complete : Serrated with central bulb (225 mm wide, 8-11 mm thick)

Construction of granular sub-base by providing close graded Material conforming to specifications, mixing in a mechanical mix plant at OMC, carriage of mixed material by tippers to work site, for all leads & lifts, spreading in uniform layers of specified thickness with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per specifications and directions of Engineer-in-Charge. With material conforming to Grade-II (size range 53 mm to 0.075 mm ) having CBR Value-25

Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in?Charge. 80 mm thick C.C. paver block of M-30 grade with approved color design and pattern.

Providing and fixing at or near ground level factory made RCC pavement slab of M-30 grade of size 450x450x50 mm, including reinforcement with 6 mm dia M.S. bars 4 nos on each side, including setting in position in footpath to the required level and line over a bed of 20 mm average thick cement mortar 1:5 (1 cement : 5 coarse sand), having joint thickness not more than 5mm except on curve, including filling of joints with same cement mortar and making grooves etc. complete as per direction of Engineer-in-charge.

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge (length of finished kerb edging shall be measured for payment). (Precast C.C. kerb stone shall be approved by Engineer?in-charge).

Painting runway/taxi track/apron marking with adequate nos of coats to give uniform finish with road marking paint of superior make as approved by the Engineer-in?charge, i/c cleaning the surface of ail dirt, scales, oil, grease and other foreign mater;al etc. and lining out complete. New work (Two or more coats)

Providing and laying solid block masonry 20cm thick using best quality blocks of available size in cement mortar 1:6 ( 1cement: 6 coarse sand )for walls at any area (including duct walls,fin walls skin / ledge wall ,kerb wall etc) . The rate including cost, conveyance and unloading at site and stacking of all materials, all labour, scaffolding, watering, curing etc complete as per the direction of Engineer in charge.

Providing and laying solid block masonry 20cm thick using best quality blocks of available size in cement mortar 1:4 ( 1cement: 4 coarse sand )for walls at any area (including duct walls,fin walls skin / ledge wall ,kerb wall etc) . The rate including cost, conveyance and unloading at site and stacking of all materials, all labour, scaffolding, watering, curing etc complete as per the direction of Engineer in charge.

Providing and laying solid block masonry 10cm thick using best quality blocks of available size in cement mortar 1:4 ( 1cement: 4 M. sand )for walls at any area (including duct walls,fin walls skin / ledge wall ,kerb wall etc) . The rate including cost, conveyance and unloading at site and stacking of all materials, all labour, scaffolding, watering, curing etc complete as per the direction of Engineer in charge.

Cement plaster 1:3 (1 cement: 3 coarse sand) finished with a floating coat of neat cement. 20 mm cement plaster

Finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)

Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface : Water thinnable cement primer

52 mm thick cement concrete flooring with concrete hardener topping, under layer 40 mm thick cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) and top layer 12 mm thick cement hardener consisting of mix 1:2 (1 cement hardener mix : 2 graded stone aggregate 6 mm nominal size) by volume, hardening compound mixed @ 2 litre per 50 kg of cement or as per manufacturer's specifications. This includes cost of cement slurry, but excluding the cost of nosing of steps etc. complete.

Providing and fixing Fiber Glass Reinforced plastic (FRP) Door Frames of cross?section 90 mm x 45 mm having single rebate of 32 mm x 15 mm to receive shutter of 30 mm thickness. The laminate shall be moulded with fire resistant grade unsaturated polyester resin and chopped mat. Door frame laminate shall be 2mm thick and shall be filled with suitable wooden block in all the three legs. The frame shall be covered with fiber glass from all sides. M.S. stay shall be provided at the bottom to steady the frame.

30 mm thick Fiberglass Reinforced Plastic (F.R.P.) flush door shutter in different plain and wood finish made with fire retardant grade unsaturated polyester resin, moulded to 3 mm thick FRP laminate all around, with suitable wooden blocks inside at required places for fixing of fittings and polyurethane foam (PUF)/Polystyrene foam to be used as filler material throughout the hollow panel, casted monolithically with testing parameters of F.R.P. laminate conforming to table - 3 of IS: 14856, complete as per direction of Engineer-in-charge.

Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete : 250x10 mm

Providing and fixing chromium plated brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete.

Providing and fixing factory made uPVC white colour sliding glazed window upto 1.50 m in height dimension comprising of uPVC multi-chambered frame with in?built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes, wire mesh and silicon sealent shall be paid separately) Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Two track two panels sliding window made of (big series) frame 67 x 50 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension . (Area of window above 1.75 sqm upto 2.50 sqm).

Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick : Float glass panes. 5.0 mm thick glass panes (weight not less than 12.50 kg/sqm).

Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to IS: 4454 - part 1 and M.S. top cover of required thickness for rolling shutters. 80x0.90 mm M.S. laths with 0.90 mm thick top cover

Extra for providing mechanical device chain and crank operation for operating rolling shutters. Exceeding 10.00 sqm and upto 16.80 sqm in the area

Extra for providing grilled rolling shutters manufactured out of 8 mm dia M.S. bar instead of laths as per design approved by Engineer-in- charge, (area of grill to be measured).

Providing and fixing ball bearing for rolling shutters.

Providing and fixing hand rail of approved size by welding etc. to steel ladder railing, balcony railing, staircase railing and similar works, including applying priming coat of approved steel primer. M.S. tube

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. Group C

Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, 2 way modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.

Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit alongwith 1 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.

Wiring for light/ power plug with 4X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit alongwith 2 Nos. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.

2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire

2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

2 X 4 sq. mm + 1 X 4 sq. mm earth wire

2 X 6 sq. mm + 1 X 6 sq. mm earth wire

2 X 10 sq. mm + 1 X 6 sq. mm earth wire

2 X 16 sq. mm + 1 X 6 sq. mm earth wire

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required.

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.

5/6 A switch

2 way 5/6 A switch

15/16 A switch

3 pin 5/6 A socket outlet

6 pin 15/16 A socket outlet

Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.

Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required.

1 or 2 Module (75mmX75mm)

3 Module (100mmX75mm)

4 Module (125mmX75mm)

6 Module (200mmX75mm)

8 Module (125mmX125mm)

Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)

8 way , Double door

12 way , Double door

16 way , Double door

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)

6 way (4 + 18), Double door

8 way (4 + 24), Double door

Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 V, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 A tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCBs (but without MCBs and incomer ) as required . (Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.)

4 way (4 + 12), Double door

8 way (4 + 24), Double door

12 way (4 + 36), Double door

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Single pole

Double pole

Triple pole

Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as required.

Supplying and fixing following rating, double pole, (single phase and neutral), 240 V, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supplying and fixing 20 A, 240 V, SPN Industrial type socket outlet, with 2 pole and earth, metal enclosed plug top alongwith 20 A "C" curve, SP, MCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket outlet and complete with connections, testing and commissioning etc. as required.

Providing and fixing M.V. danger notice plate of 200 mm X 150 mm, made of mild steel, at least 2 mm thick, and vitreous enameled white on both sides, and with inscription in single red colour on front side as required.

Providing and fixing H.T. danger notice plate of 250 mm X 200 mm, made of mild steel, at least 2 mm thick, and vitreous enameled white on both sides, and with inscription in single red colour on front side as required.

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray (Galvanisation thickness not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required.

150 mm width X 50 mm depth X 1.6 mm thickness

300 mm width X 50 mm depth X 1.6 mm thickness

600 mm width X 50 mm depth X 2.0 mm thickness

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray "bends" (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required.

150 mm width X 50 mm depth X 1.6 mm thickness

300 mm width X 50 mm depth X 1.6 mm thickness

600 mm width X 50 mm depth X 2.0 mm thickness

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray "Tee" (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required.

150 mm width X 50 mm depth X 1.6 mm thickness

300 mm width X 50 mm depth X 1.6 mm thickness

600 mm width X 50 mm depth X 2.0 mm thickness

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray "Cross member"(galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc as required.

150 mm width X 50 mm depth X 1.6 mm thickness

300 mm width X 50 mm depth X 1.6 mm thickness

600 mm width X 50 mm depth X 2.0 mm thickness

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray "Reducer" (galvanisation not less than 50 microns) with perforation not more than17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc as required.

150 mm width X 50 mm depth X 1.6 mm thickness

300 mm width X 50 mm depth X 1.6 mm thickness

600 mm width X 50 mm depth X 2.0 mm thickness

Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required.

Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

Supplying and laying 25 mm X 5 mm copper strip at 0.50 metre below ground as strip earth electrode, including connection/terminating with nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of brass nut bolt & spring washer spaced at 50mm)

Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth electrode, including connection/terminating with G.I. nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm)

Providing and fixing 25 mm X 5 mm copper strip on surface or in recess for connections etc. as required.

Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required.

Providing and fixing 4.00 mm dia copper wire on surface or in recess for loop earthing along with existing surface/ recessed conduit/ submain wiring/ cable as required.

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing masonry open duct as required.

Upto 35 sq. mm

Above 35 sq. mm and upto 95 sq. mm

Above 95 sq. mm and upto 185 sq. mm

Above 185 sq. mm and upto 400 sq. mm

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on cable tray as required.

Upto 35 sq. mm (clamped with 1mm thick saddle)

Above 35 sq. mm and upto 95 sq. mm (clamped with 25x3mm MS flat clamp)

Above 95 sq. mm and upto 185 sq. mm (clamped with 25/40x3mm MS flat clamp)

Above 185 sq. mm and upto 400 sq. mm (clamped with 40x3mm MS flat clamp)

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 11 KV grade of following size in the existing masonry open duct as required. Above 120 sq. mm and upto 400 sq. mm

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.

3½ X 25 sq. mm (28mm)

3½ X 35 sq. mm (32mm)

3½ X 50 sq. mm (35mm)

3½ X 70 sq. mm (38mm)

3½ X 95 sq. mm (45mm)

3½ X 150 sq. mm (50mm)

3½ X 185 sq. mm (57mm)

3½ X 400 sq. mm (82mm)

4 X 10 sq. mm (25mm)

4 X 16 sq. mm (28mm)

Supplying and making indoor cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for following size of 3 core, XLPE aluminium conductor cable of 11 KV grade as required :

RMU Outdoor IP 66, 3 Panel, 12KV, 21KA for 3SEC, 630A Data Acquisition compatible, Both side extensible type compact, SF6 GAS INSULATED Ring Main Unit (RMU) with suitable capacity SMF battery and charger, 25x6 mm external copper Bus. This shall be as per KSEB requirement & standard specification. Rate shall include the foundation and necessary civil works if any. Incomer type 1 (OD) > Quantity 1No. 1No. 12kV, 630A, 3P, Load break switch with earth switch having 24V DC Motor operated snap acting mechanism, Arc proof cable cover with interlocking, Cable bushings, 9-15KV Capacitive voltage indication, Earth fault indicator, 2NO + 2NCAuxillary switch Incomer type 2 (OD) > Quantity 1No. . 12kV, 630A, 3P, Load break switch with earth switch having 24V DC Motor operated snap acting mechanism, Arc proof cable cover with interlocking, Cable bushings, 9-15KV Capacitive voltage indication, 2NO+ 2NCAuxillary switch Outgoing type 1 (VL) > Quantity 1No.1No. 12kV, 630A, 3P, Vacuum circuit breaker with earth switch having 24V DC Motor operated stored energy spring charging type mechanism, Arc proof cable cover with interlocking, Cable/busbar bushings, 9-15KV Capacitive voltage indication, Self powered Microprocessor based 2 O/C + 1No. E/F Relay with 3nos protection class cast resin CTs, Shunt trip Coil, 2NO + 2NCAuxillary switch

11KV Outdoor Metering Cubicle SITC of 11KV Outdoor Metering Cubicle comprising of : 3 Nos. Current transformer (---/5A,15VA,class 0.2s) 1 No. Potential transformer(11KV /110V,100VA,class 0.2) Separate Compartment for CT/PT and TOD Meter with KSEB sealing facility TTB with Fuse and Carrier Provision for incoming and outgoing XLPE 11 KV Cable and cable entry from bottom side with cable box suitable for 3 x 300 sqmm XLPE, 11KV Al: cable Enclosure-Powder coated CRCA sheet 2MM –IP 54

11KV TOD Meter SITC of 11KV/ √3 / 110V/ √3 , Class 0.2S , 15VA HT TOD Meter suitable for mounting outdoor type with all standard accessories. 11 KV KSEB metering cubicle, lead wires etc.complete Carrying CT/PT units with TOD meter for testing and calibrating at the KSEB Testing Lab and taking back the same to the site is included in the scope of the contractor.Statutory testing fees shall be remitted and will be reimbursed against producing original receipt

11kV/433v,320KVA Cast Resin Transformer SITC of Transformer comprising of : 11kV/433V ,400KVA ,50Hz,3phase,Vector Dyn 11 Resin Cast Indoor Transformer with off circuit tapping +5% to -5% in steps of 2.5% with winding temperature indicator and hooter with all standard accessories as per IS 2026/77 on HV side Rigid Bus Bar interonnection to the 11KV LBS Panel and on LT side cable box suitable for 3 x 3.5 x 300 sq.mm XLPE Al ; cable with all standard fittings and accessories.Painting shall be carried out as per IS 631, impedance of the transformer shall be as per relevant standards.

NEUTRAL CTs Supply & Fixing of 1no Cast Resin Neutral CT with ratio 120/5A ,10VA, Cl.5P10, fixed in a suitable M.S box with view glass.

Supply & Fixing of 1no Cast Resin Neutral CT with ratio 120/5A ,10VA, Cl.5P10, fixed in a suitable M.S box with view glass.

HT CABLES Supply of 11KV stranded compact circular aluminium conductor,conductors insulation screened with extruded semi conducting compound in combination with copper tape (0.3 kA for 1 sec.), cores laid up, inner sheath of PVC tape,galvanized steel flat strip armoured,and overall PVC sheathed cable conforming to IS 7098/11/85 with latest amendments & confirming to the GTP of Group A of following sizes. 3C - 300 Sq.mm HT Cable

SITC of D.G. set of following KVA 0.8 P.F.3 phase,50c/s,433V, comprising diesel engine, fuel tank, base plate, antivibration pad, battery, battery lead wire, battery charger self starting and self charging mechanism, and residential type silencer, control panel , in accoustic enclosure etc.with all standard accessories as per Electrical Inspectorate standards and pollution control board norms. 320 KVA

Supply & Fixing of 1 No. Cast Resin Neutral CT fixed in a suitable M.S. box with view glass. 90/5A, 10VA, Cl.5P10

L.T.PANELS SITC of cubicle type medium voltage switch boards as per specifications mentioned below, comprising of ACBs / MCCBs., enclosed in 16 guage M.S.cubicle complete with angle iron frame work, panel doors , horizontal and vertical busbars and outgoing feeders, FRP separators, phase barriers, gaskets for door, feeders designations, etc., Main Switch Board shall be capable of withstanding 50 KA fault level. The panel shall be suitable for erection on the floor using channel and fastners at regular intervals. All panels should have fire suppression system( Panel should confirm to BIS,IE rules,KSEI/ KSEB Standards)

MAIN MV PANEL

APFC PANEL - 150 KVAr

SSB GF

SSB FF

SSB SF

SSB COMMON

SSB HVAC

SSB MEDICAL EQPT

LIFT PANEL

UPS PANEL - MEDICAL EQUIPMENT

UPS PANEL - 10KVA

UPS PANEL - 30KVA

30 KVA UPS - Three Phase SITC of 30kw Frame with 5kw x 6 modules three phase in and out. with indoor (IP21) with surge protection system with 60 min backup battery @ 30kva .8 PF load with min VAH of 48000 Dual string (SMF battery of reputed approved make. Input pf >0.99, with external input isolation transformer, with IGBT rectifier and inverter Double conversion technology, with input voltage range 320-460 @ full load, 50Hz Three Phase, output 400V, 50Hz Three phase, compatibility etc.

10 KVA UPS - Three Phase SITC of 10kw Frame with 3.4kw x 3 modules three phase in and out. With indoor (IP21) with surge protection system with 60 min backup battery @ 10kva .8 PF load with min VAH of 16320 Dual string (SMF battery of reputed approved make. Input pf >0.99, with external input isolation transformer, with IGBT rectifier and inverter Double conversion technology, with input voltage range 320-460 @ full load, 50Hz Three Phase, output 400V, 50Hz Three phase, compatibility etc.

125 KVA UPS - Three Phase SITC of 30kw Frame with 20kw x 6 modules three phase in and out. with indoor (IP21) with surge protection system with 60 min backup battery @ 120kva 0.8 PF load with min VAH of 48000 Dual string (SMF battery of reputed approved make. Input pf >0.99, with external input isolation transformer, with IGBT rectifier and inverter Double conversion technology, with input voltage range 320-460 @ full load, 50Hz Three Phase, output 400V, 50Hz Three phase, compatibility etc

Supplying following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.

3½ X 25 sq. mm

3½ X 35 sq. mm

3½ X 50 sq. mm

3½ X 70 sq. mm

3½ X 95 sq. mm

3½ X 150 sq. mm

3½ X 185 sq. mm

3½ X 400 sq. mm

4 X 10 sq. mm

4 X 16 sq. mm

Wiring for light point/ fan point / exhaust fan point / call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc. as required for;

Two light controled by one switch.

Three light controled by one switch.

Four light controled by one switch.

Five light controled by one switch.

S' type M.S. fan hook fabricated from suitable dia. M.S. rod duly painted for fixing of ceiling fan. The 'S' type hook shall be fixed to steel bar in RCC ceiling. The ceiling shall be replastered with sand, cement & neeru etc. The cost of labours for chipping out ceiling upto steel bar & fixing of 'S' hook & resurfacing the ceiling is included in the cost of item

Readymade 2500mm standard length, prefabricated, GI trunking from MS sheet and then hot dip galvanised, of following sizes and associated accessories such as coupler plates, tees, elbow etc. 50 mm side flanges shall be provided. Galvanisation thickness shall be minimum 86 Micron. cost of trunking shall be included junction box of suitable size, and all other accessories required to complete the work.

100 x 40mm (W x H) - (14 SWG - 2mm) with cover without partition

150 x 40mm (W x H) - (14 SWG - 2mm) with cover without partition

300 x 40mm (W x H) - (14 SWG - 2mm) with cover without partition

IP 44 SS Floor Box (120 x 120 mm) - Flush mount floor box for concrete floors, IP 40 - for 3 Mosaic modules

SITC of following Light Fixtures/Ceiling Fans / Exhaust Fans

LED Downlight Recessed Fitting 15 W

LED Downlight Recessed Fitting 12 W

LED Recessed Luminaire 36Watts

LED Linear Fixture 20Watts 4ft Surface Mounted

Mirror Light 5W

Ceiling Fan -1200 mm ( BLDC)

Exhaust Fan -450 mm

Bollard Lights

50W Flood Light

80W Flood Light

Providing and fixing Fully Solid Vertical Air terminals for wind stability as per IS/IEC -62305 part-3. For 1,2,3,4 meter air terminal 16mm rod tapered to 10 mm aluminium rod meter rod: Meets the requirement (IS/IEC 62305). Semi-hard (E-AlMgSiO5) Suitable for high wind load. All air terminal must have Interception Tip at the Top of air terminal. System consist of Fang Fix with base and clamp on the top air terminal is erected. Air terminal Joining Clip Stainless Steel SS 304 clamp made of cable bracket, lightning tested for 100 KA 10/350 micro sec waveform. Stainless Steel Wall Clamp or 16 KG stone of 365 mm diameter, high level of stability. No. of stones/wall clamps depending on wind load. Quick and easy mounting of interception rod using anchors. Concrete, frost-resistant, can be stacked. Govt approved Indian labs test certificate required. Make: Cape/Dehn

2 meter air terminal with Interception Tip mounted on Stainless Steel Wall Clamp mounting accessories.

Providing & fixing of 8mm solid aluminium round conductor with necessary holders @ required interval as specified below: Meets the requirement of (IS/IEC 62305) : semi-hard (E-AlMgSiO5 )with 50 sq.mm cross sectional area. Govt approved Indian labs test certificate required. Make: Cape/Dehn

Conductor with Down Conductor Holder made of whether resistant plastic holder @ every 0.75 meters

Conductor with Terrace Conductor Fibre Reinforce Concrete holder @ every 0.75 meters

T-Connectors Providing and fixing of Cross Connector/T Connector/Folding Clamp/Clamping Shoe/ Expansion Piece: to route vertical down conductor /mesh formation made of Aluminium Ferrule using screw free joints. Folding Clamp/Clamping Shoe for metal panels (up to 20mm thickness of the metal frame): Folding clamp/clamping shoe for metal frame thickness up to 20mm, made of stainless steel SS 304/316 grade , conforms to the requirements according to (IS/IEC 62305). Expansion piece with connector: For equalising temperature related length changes. Necessary on conductors length at every 20 meters horizontally. Using round conductor 8mm aluminium conductor with straight Connector: using Aluminium Ferrule. Quick installation using crimp joints. Conforms to the requirements according to (IS/IEC 62305). Make sure all joints are strong and will be inspected at site. Galvanised Iron joints are not permitted to avoid risk of corrosion. Single bolt joints are not permitted to avoid risk of faulty loose joints and reduce risk of flash over. Govt approved Indian labs test certificate required. Make: Cape/Dehn

Test Joints Providing and fixing of Stainless Steel Test Joint suitable with suitable Outdoor Enclosure: For 8mm dia solid round aluminium conductor & 10mm dia copper coated solid steel round conductor having 100 microns of copper bonding . Conforms to the requirements according to (IS/IEC 62305).The enclosure should be outdoor glass-fibre reinforced polycarbonate opaque having minimum inner dimension of 75mm x 75 mm x 50 mm. The test link has to be straight and needs minimum 4 mounting screws for strong joints Inspection of bimetallic corrosion at site required. Seperation of 8mm Aluminium & 10mm Copper bonded steel is required for future inspection and contractor has to make sure both conductors permitted. Govt approved Indian labs test certificate required. Make: Cape/Dehn

Ring Earthing

Providing and laying copper coated steel solid round conductor 10mm diameter from earth electrode directly in ground as required. copper coated steel, high corrosion resistant. Meets the requirement of (IS/IEC 62305) copper coating thickness of 100microns Should be tested and use exclusively for lightning protection earthing system and ring equipotential bonding. After test link needs to be routed inside Heavy duty conduit to avoid touch potential till ground level. Govt approved Indian labs test certificate required. Make: Cape/Dehn

Welded Joints Installation of Exothermic Weld Joints for 10mm round copper bonded steel conductor having 100 microns as per IS/IEC 62305. Each under ground joints has to be wrapped with petrolatum- coated chemical fibre fabric having 1.1mm thick and width 50mm. Govt approved Indian labs test certificate required. Make: Cape/Dehn

Earth Pits Providing and fixing of maintenance free Earthing system comprises of molecularly bonded copper of 99.9% purity on low carbon steel of min 3048mm length (10 feet), having a diameter of 20mm with copper bonding thickness of 250 microns as per UL 467. The Rod has to be either continuous or with self-coupling peg & bore arrangement with fault current withstand capability of 30 KA rms value for 1 second and I peak of 76 KA The rod must be having corrosion test, peel off test for uniform coating, 180 degree bend test with out peeloff of copper bonding. Exothermic welded Clamp for clamping as suggested as per NBC 2016.Ordinary Stainless steel/Copper alloy universal clamps are not recommended. For self coupling peg & bore arrangement rod needs Impact point on the bottom rod for easy insertion. Earth enhancing mineral compound is used for improving the soil conductivity. The material shall be mineral inert to sub soil and shall not pollute the environment and non corrosive to earth rod. The material should have a resistivity less than 0.2 Ωm. It should be free from hazardous substances.The mineral compound is required to have minimum 17.5 Kg of the total composite.The compound should be chemically inert and needs to submit Govt approved Indian labs test certificate. Concrete Earth electrode inspection chamber with weight bearing capacity of 50KN. The dimension shall be 320mmx 320mmx 190mm. Govt approved Indian labs test certificate required. Make: Cape/Dehn

SITC of Solar Street Light mounted on 2.5 inch dia. 5 meter height G.I Post comprising of : 60W Monocrystalline panels , 26Ah Gell Battery , 15 Watts LED Street Light, Powder doated battery box and automatic ON/OFF Sensor etc. complete.

Solar Panels: 60 KW (DC Output). Supply and Installation of 320 Wp X 19 Nos. Poly Crystalline Modules Grid Tie Inverter -200 KW suitable for 60 KW DC "EPC (Engineering, Procurement & Commissioning): Design, Supply, Installation, Testing and Commissioning of turnkey project including following works: Civil, Mechanical & Electrical works Hot Dip Galvanized Module mounting structure AC & DC Copper Solar Application Cables Earthing for Solar Structure and Inverter Remote Monitoring Balance of System (BOS): Conducting material, Metal Trays,Switches, SPD’s, AC/DC Disconnect, clips, fasteners, MC4Connectors etc. as per actual

Supply and drawing of UTP 4 pair Cat 6 LAN cable in the existing surface/recessed PVC conduit as required.

one run

Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc..direct in ground (75 cm below ground level) including excavation and refilling the trench but excluding sand cushioning and protective covering etc., complete as required.

63 mm dia (OD-63 mm & ID-51 mm nominal)

Supplying and drawing 2 pair, 0.5 sq mm FR PVC insulated copper conductor, un armoured telephone cable in the existing surface/recessed steel/ PVC conduit.

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc as required.

Telephone socket

Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/ recessed steel/ PVC conduit as required

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc as required.

TV antenna socket outlet

Supply, installation, testing and commissioning of IP based IR Varifocal dome Camera, 1/3" CMOS, 3 MP, 2.7–12 mm MFZ, night vision compatible,IR range of 40 mtrs PoE, inbuilt micro SD card,Ethernet port, H.264, IP 66, ONVIF, UL, FCC & CE certified. All mounting accessories shall be included

Supply, installation, testing and commissioning of IP based IR bullet Camera, 1/3" CMOS,3 MP, night vision compatible,IR range of 40 mtrs PoE, inbuilt micro SD card,Ethernet port, H.264, IP 66, ONVIF, UL, FCC & CE certified. All mounting accessories shall be included

Supply, installation, testing and commissioning of IP based IR PTZ camera, 1/3" CMOS, 2 Megapixel,30X zoom, WDR, IR range of 200 Meters, inbuilt micro SD card,,Ethernet port,TDN, PoE, DWDR, BLC, AGC, DNR, OSD,H.264 High Profile dual-stream, ONVIF, Wall/corner Mount, IP-66. CE, FCC, C-Tick certified. All mounting accessories and mounting arm suitable for the location shall be included

Supply,installation, testing and commissioning of IP Network Video Recorders 16 channel with 16 ports, 2 SATA, audio 1 input 1 output, video 1 HDMI 1 VGA, recording resolution 5MP/3MP/1080P, 720P/ D1 @ 30 fps, network throughput 200 Mbps from IPC and 128 Mbps to Client, Smart search supported, Remote access by DDNS & P2P, 4 channel alarm input and 2 channel relay output, 2 USB ports, ONVIF, UL & CE certified.

Supply, installation, testing and commissioning of 20 100/1000 SFP ports + 4 Combo 10/100/1000BASE-T/SFP ports + 4 10G SFP+ ports, L2 Management Switch - Core Switch

Supply, installation, testing and commissioning of 8 port- Edge PoE switch

Supply, installation, testing and commissioning of 24 port- Edge PoE switch

Supply, installation, testing and commissioning of Patch Panel UTP Keystone- 24 Port- Fully loaded (Cat 5e,Cat 6 & Cat 6 A )

Supply and installation of Cat 6 UTP patch cord, 1 mtr

Supply, installation, testing and commissioning of Server PC, Intel i7 processor, 24 inch LED monitor, Gigabit LAN port, USB port, 8GB DDR3 RAM,1TB HDD,1GB dual graphic card, 100/1000 LAN ports, optical mouse, Keyboard, DVD Writer. Genuine Win 8.1 Pro - Down grade to Win 7 professional, 24 inch LED monitor

Supply, installation, testing and commissioning of Professional Joystick designed for Surveillance application as compatible with the above mentioned system. UL+CE+FCC certification minimum.

Supply, installation, testing and commissioning of Surveillance / ESATA compatible Hard Disk of 4TB capacity to achieve the total storage for the NVR server

Supply, Installation, Testing & Commissioning of 42 inch full HD LED monitor with resolution 1920X1080 pixel including wall mounting accessories (location: security room & central control room).Material shall be UL/CE listed

Supply and installation of wall mounted 22U rack including cable manager, power supply units etc.to accommodate NVR, ethernet switch patch panel etc in control rooom

Supply, installation, testing & commissioning of column speaker 6 watts

Supply, installation, testing & commissioning of 6 watts ceiling speakers

Supply, installation, testing & commissioning of voice alarm call Station with all cables and accessories

Supply, installation, testing & commissioning of voice alarm keypad - Extension to voice alarm call station with all cables and accessories

Supply, installation, testing & commissioning of voice alarm controller with all cables and accessories

Supply, installation, testing & commissioning of voice alarm router with all cables and accessories

Supply, installation, testing & commissioning of 480 W Booster Amplifier with all cables and accessories

Supply, installation, testing & commissioning of DVD/MP3Player for audio playback only

Supply, Installation, Testing & Commissioning of Paging Microphone, goose neck type

Supply, laying and termination of Shielded Cat6 cable with all necessary accessories

Supply, laying and termination of 2 Core x 1.5 Sq.mm Armoured Al.Mylar Screened FRLS Twin Twisted PVC Insulated cable along with all accessories. Accessories include cable glands, locknuts,saddle clips, cable tie & other hardwares to achieve cable termination and installation. Cable shall be terminated in speakers and amplifiers

Supply, installation, testing & commissioning of standard AV rack with 600mm Width, 800 mm Outer Depth and 36U Height

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc as required.

RJ 45 socket

Supply and installation of Cat-6 shuttered 24 port patch panel

SITC of 24 port unmanaged ethernet switch

Supply and installation of 9U rack with Front glass door, Rear Perforated door with handle Lock & key. Front/Rear 19" mounting angles, top, bottom open, RAL 9005 with all other accessories

AX3600 WIFI6 Dual Band Multi Band Multi Gigabt Ceiling Mount Access Point / EAP660HD

Supply,laying and termination of 20 pair telephone cable, 0.5mm copper PVC insulated,unarmoured telephone cable drawn in the existing cable tray

Supply,laying and termination of 20 pair telephone terminal block housed in engineering plastic box with transparent hinged door

Supply,laying and termination of 10 pair telephone cable, 0.5mm copper PVC insulated,unarmoured telephone cable drawn in the existing cable tray

Supply,laying and termination of 10 pair telephone terminal block housed in engineering plastic box with transparent hinged door

Supply, Installation, Testing & Commissioning of Patient Handsets - type with wired console unit

Supply, Installation, Testing & Commissioning of Patient Handsets - type

Supply, Installation, Testing & Commissioning of Toilet Pull Cords with all the necessary accessories for the installation.

Supply, Installation, Testing & Commissioning of Light Modules with all the necessary accessories for the installation.

Supply, Installation, Testing & Commissioning of Nurse Station Terminals with all the necessary accessories for the installation.

Supply, Installation, Testing & Commissioning of system switch communiction accessories

Supply, Installation, Testing & Commissioning of management software alongwith workstation

SITC of Queue Management System Consisting of multi function queue ticket printer with touch screen kiosk type diplay , Voice Unit & Customer Identification devices, High Resolution GUI display in multi languages, support wireless networks, durable printer, supports alpha numeric numbering system

Display system with 24" LCD Monitor, with audio speaker arrangement, HDMI Cabling

Workstation counters

Browsers/ Softwares and inclusive of testing, commissioning and training to treasury officers for Queue management system by OEM.( Necessary softwares& hardwares required for the effective functioing of QMS)

20BED LIFT

Equipement Details : Machine Roomless - Gearless

No. of Unit : One

Controller Type : Micro Processor Based VVVF

Capacity in Kgs/Persons : 1360Kg/20P

Speed in MPM : 60mpm/1.0mps

Door Opening Type : Centre Opening Sliding Door

Operation : Simplex

No.of Stops : 4 (G,1,2,T)

No.of Openings : 4 (G,1,2,T)

Storey Served Front : 4 (G,1,2,T)

Travel (mm) : 12700mm

Hoistway Size (mm) : 2400 (w) x 3000 (d)

Cabin Dimemnsions (WxDxH) (mm) : 1300x2400x2350

Pit Depth (mm) : 1500

Overhead (mm) : 4250

Entrance Dimensions (mm) : 1200x2100

Ceiling : SS Honeycomb finish with LED Downlight

Car Front/Rear/Side Panel : SS Honeycomb finish

Handrail : 38mm dia

Car Doors : SS Honeycomb finish

Car Flooring : Vinyl Tile

Floor Thickness : 1.5mm Thick Vinyl Tile

Car Sill : Extruded Hard Aluminium

Entrance Frame/Landing Doors : SS Honeycomb finish

DUMB WAITER

Equipement Details : Machine Roomless - Gearless

No. of Unit : One

Controller Type : Micro Processor Based VVVF

Speed in MPM : 60mpm/1.0mps

Door Opening Type : Centre Opening Sliding Door

Operation : Simplex

No.of Stops : 4 (G,1,2,T)

No.of Openings : 4 (G,1,2,T)

Storey Served Front : 4 (G,1,2,T)

Travel (mm) : 12700mm

Pit Depth (mm) : 1500

Overhead (mm) : 4100

Ceiling : SS Honeycomb finish with LED Downlight

Car Front/Rear/Side Panel : SS Honeycomb finish

Handrail : 38mm dia

Car Doors : SS Honeycomb finish

Car Flooring : Vinyl Tile

Floor Thickness : 1.5mm Thick Vinyl Tile

Car Sill : Extruded Hard Aluminium

Entrance Frame/Landing Doors : SS Honeycomb finish

Providing and fixing white vitreous china extended wall mounting water closet of size 780x370x690 mm of approved shape including providing & fixing white vitreous china cistern with dual flush fitting, of flushing capacity 3 litre/ 6 litre (adjustable to 4 litre/ 8 litres), including seat cover, and cistern fittings, nuts, bolts and gasket etc complete.. Make: Jaquar, Kohler, Grohe, Cera high end series.

Providing and fixing wash basin with C.I. brackets, 15 mm dia CP Brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required:- (a) White Vitreous China Wash basin size 550x400 mm with a 15 mm CP Brass single hole basin mixer Make: Jaquar, Kohler, Grohe, Cera high end series.

Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350 mm with white PVC automatic flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and other couplings in C.P. brass, including painting of fittings and cutting and making good the walls and floors wherever required : Single half stall urinal with 5 litre P.V.C. automatic flushing cistern Make: Jaquar, Kohler, Grohe, Cera high end series.

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing stainless steel toilet paper holder. Make: Jaquar, Kohler, Grohe, Cera high end series.

600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms

Providing and fixing PTMT towel ring trapezoidal shape 215 mm long, 200 mm wide with minimum distances of 37 mm from wall face with concealed fittings arrangement of approved quality and colour, weighing not less than 88 gms.

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : Kitchen sink with drain board 510x1040 mm bowl depth 250 mm Make: Jayana, Nirali, Carysil high end series.

Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms.

15 mm nominal bore

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931

15mm nominal bore

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC SDR 11) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.Internal work - Exposed on wall (Above ceiling and Ducts)

15 mm nominal outer dia Pipes

20 mm nominal outer dia Pipes

25 mm nominal outer dia Pipes

32 mm nominal outer dia Pipes

40 mm nominal outer dia Pipes

50 mm nominal outer dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. Make: Astral, Supreme, Finolex, Prince

20 mm nominal outer dia Pipes

25 mm nominal outer dia Pipes

Providing and supplying ISI mark CI D/F Butterfly Valves as per IS:13095 (Latest Edition) of PN 10 and 50 mm diameter including all taxes, insurance, transportation, freight charges, octroi, inspection charges, loading, unloading, conveyance to departmental stores, stacking etc. complete.

Providing and supplying ISI mark CI D/F Butterfly Valves as per IS:13095 (Latest Edition) of PN 10 and 40 mm diameter including all taxes, insurance, transportation, freight charges, octroi, inspection charges, loading, unloading, conveyance to departmental stores, stacking etc. complete.

Providing and fixing Gun metal check or non-return fullway wheel valve.(E) 40mm dia.

Providing and fixing wash basin with C.I. brackets, 15 mm dia CP Brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required:- (a) White Vitreous China Wash basin unter counter type 550x420 mm with a 15 mm CP Brass single hole basin mixer . Make: Jaquar, Kohler, Grohe, Cera high end series.

Providing and fixing wash basin with C.I. brackets, knee operated 15 mm dia CP Brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required:- (a) Stainless steel 316 grade A ISI 304 (18/8) Wash basin with pedestal400x400 mm with a 15 mm CP Brass single hole basin mixer 400x400, Pillar Cock, CP Waste Coupling,with extention pipe, required sealent and other accessories to fix the wash basin with 450mm long flexible CP inlet connection pipe, CP Wall flange all of approved make etc. including all necessary accessories complete. (Diamond WB133 Or Equ.) . Make: Jaquar, Kohler, Grohe, Cera high end series.

Fixing, Commissioning at site Urinal Partition with Curved shaped frosted glass fixing with brass screws, nuts , and washers complete including cutting and making good the walls and floors wherever requiredEtc complete. 900x450x10 mm tk. Make: Jaquar 1110uc/ equ.

Providing and fixing of grab bars 300 mm Stainless steel in physically disabled toilet including all necessary fitting, SS Screws & Accessories etc.Complted in all manners and satisfied to of EIC. complete. Make: Jaquar, Kohler, Grohe, Hindware, Cera high end series.

Providing and fixing of grab bars Vertical Swing 18-8 S, type-304, 18-gauge (1mm) stainless steel tubing with satin-finish. 1–1/4 (25mm) outside diameter wall mounted in physically disabled toilet including all necessary fitting, SS Screws & Accessories etc.Complted in all manners and satisfied to of EIC.complete. Make: Jaquar, Kohler, Grohe, Hindware, Cera high end series.

Fixing, Testing and Commissioning at site ablution Health Spray Faucet with wall hook and 1.2 mtr. Chrome plated PVC hose pipe, etc. complete in all respects. Queo - Addons/Kohler/Grohe/jaquar

Fixing, testing and commissioning of Single Lever Diverter with provision for spout and over head shower with shower arm, shower rose, wall flange and spout, all accessories etc, complete.Queo - (Aquaplan +F Elegant)/ KOHLER K-14795IN-CP/Grohe Metropole, jaquar OR Equ.

Fixing CP Robe hook: Queo - Q363196120/ KOHLER K-97499T-CP/Grohe 41711,jaquar OR Equ.

Supplying,Fixing, Testing, and commissioning Sink Mixer wall mounted/floor mounted with swivel casted spout and wall flange, trending cutting and making good the walls whatever required etc. complete Queo - Allamoda/jaquar/Kohler/Grohe

Supplying, Fixing, testing and commissioning at site Stainless Steel Sink with drain board and double bowl , depth 200mm manufactured from 1mm thick stainless steel, 18G high grade indestructible chrome nickel steel with top quality polish, 40mm dia full threaded CP waste coupling, with all accessories etc complete.Nirali Greaceful elagance/ Diamond super delux

Providing and Fixing of Stainless Steel Hand Dryer with all required connections and following specifications. Weld-free cover fixed to the base with two safety screws and lock withspecial speedflow key. Aluminium base. Includes silent-blocks to damp mechanical vibrations. Fire resistant plastic UL 94-V0 fan scroll. High-speed motor with safety thermal cut-off.The motor revolutions canbe adjusted manually by the potentiometer. • Aluminium centrifugal double asymmetrical inlet fan wheel. Disconnects automatically after 60 seconds of continuous use. Electronic infrared detection sensor. Adjustable detection by potentiometer(5- 25 cm). Ultra-flat: 10 cm deep (complies with ADA regulations). complete. Make: Jaquar, Kohler, Grohe, Hindware, Cera high end series.

Supplying, Fixing, testing and commissioning at site in position uPVC pipe -6kg/cm2) (IS:4985) Solvent Welded fittings with bosses where required e.g. tees, bends, coupling, door bends, junctions, cowls, door TEE , Door Elboe where ever required etc., complete. (Soil & Waste in Shaft) Make: Astral/Supreme/Ajay

IN SHAFT

110 mm O.D. (6Kgf/cm2 IS:4985)

75 mm O.D.(6Kgf/cm2 IS:4985)

63 mm O.D ( 4Kgf/cm2) Vent pipe in shaft

Providing, Fixing, testing and commissioning at site in position uPVC pipe ( IS : 4985 ) With Rubber Ring or Solvent Welded fittings with bosses where required e.g. tees, bends, coupling, etc. complete. (For Rain water pipes in shaft & Ceiling) Make: Astral/Supreme/Ajay

110 mm O.D ( 4Kgf/cm2)) Rain water pipe in shaft

Supplying, Fixing, testing and commissioning at site in position u PVC pipe of 6Kgf/cm2including PVC fittings with bosses where required e.g. tees, bends,door TEE , Door Elboe where ever required coupling and adapters and jointing with adhesive approved by fitting manufactures including cutting and making good the walls and floors or surface mounted with clamps as required at site universal clamps & anchor fasteners(8mm) , threaded rod(8mm),nuts ,washers, wherever required etc. complete.Make: Astral/Supreme/Ajay

(For Internal Soil &Waste line) (PASTED ONLY)

40 mm O.D. (6Kgf/cm2 IS:4985)

50 mm O.D. (6Kgf/cm2 (IS:4985)

75 mm O.D. (6Kgf/cm2 (IS:4985)

110mm O.D (6Kgf/cm2 (IS:4985)

32 mm O.D. (8Kgf/cm2 (IS:4985) for sunken spout

Supplying, Fixing, testing and commissioning at site in position Deep Seal UPvc fabricated Multi floor trap (4”), with suitable supporting on GI slotted rails (1.6mmthick) full threaded rod, anchor fasteners etc. complete in all respects. 50/75 mm dia outlet (In Ceiling)Astral/Supreme/Ajay

Supplying,Fixing, testing and commissioning at site in position UPvc fabricated Multi floor trap (4”), with 50/75 mm dia outlet (In Sunken slab & floor raising areas)Astral/Supreme/Ajay

Supplying,Fixing, Testing and commissioning at site in position 150x150mm square C.P cast brass or stainless steel anti cockroach grating cover ss (304) of matching size of UPvc fabricated floor trap / multi inlet trap complete in all respects. Chilly/Eligna/

Supplying,Fixing, Testing and commissioning at site in position 150x150mm square C.P cast brass or stainless steel sealed grating cover ss (304) of matching size of UPvc fabricated floor trap / multi inlet trap complete in all respects. Chilly/Eligna/ in common toilets

Supplying,Fixing, testing at site in position 160mm dia square /circular grating Terrace rain water outlet (Cast Iron)(for 110mm dia pipe)

Supplying, Fixing, testing at site in position PVC Roding Eye (6kg/cm2) Complete in all respects.

110 mm dia

75 mm dia

Providing and fixing in position cowel went to pipes.(C) 100mm dia

Supplying, Fixing, testing and commissioning at site Puddle Flange fabricated from Upvc ASTM Grade sch-40 pipes & uPVC sheet (600 mm long)

2 ” (50mm) dia

Supplying, Fixing, testing and commissioning at site Puddle Flange fabricated from 100 mm dia GI pipe with 6mm tk plate (600 mm long) for FIRE Tank

Supplying and Laying of pipes and conveying to position; cleaning, laying and jointing to true lines and gradients, with proper bedding uPVC pipe of IS 4985(6kgf/cm2) including jointing the pipe as per specification, testing the pipe line after installation all per provisions of IS: 1742-1983 (Code of practice for building drainage) complete as directed by the Employer

160 mm OD (6/kg/cm2)

Providing and supplying of Class SN8 Structured Wall polyethelene Piping systems (Pipe with online/offline coupler and elastomeric sealing ring) with non-smooth External Annular Corrugated and Smooth Internal Surfaces (Double Wall) for non-pressure underground Sewerage & Drainage application as per EN:13476-3 including all local and central taxes, transportation, freight charges, octroi, inspection charges, loading, unloading, conveyance to the departmental stores etc. complete.(ID 150 mm diameter) Make: Astral, Supreme, Finolex, Prince

160 mm OD (6/kg/cm2)

200 mm OD (6/kg/cm2)

Supply, installation, testing and commissioning of percolation well (Recharge well) including all work like drilling, compressor work, gravel packing, mud slurry disposal, clay packing and including of all materials like 300mm UPVC pipe, 300mm wire screens, 300mm collar joint, accessories, gravels, sand, sand filteration module etc. Site cleaning, mud pit, mud refilling for borewell must be in the contractor's scope. Contractor has to maintain the percolation well upto three years after installation.

Supply,Installation, Testing and commissioning of Clear water transfer open well submerssible pump of adiquate hp with discharge 3 lps at 20 mtr head, SS body, ss shaft with bronze impeller mounted on a single base plate with controll panel and auto level controller.

1 working+ 1 stand by

TERRACE DWS BOOSTER PUMP Duty Conditions of 6 lps @ 35 mtr - head(Each pump3LPS 35 mtr Head - 2 Pump system-1 Working+1standby) Compact skid mounted Booster pumps with SS 304 casing, SS316 impeller , SS316 shaft , C I base and TEFC motor with mechanical seal. Pump to be have single VFD logic controller. - Electric control panel with logic controller, relays, calibrated pressure switch, pressure transmitter including cabling within panel, incorporating dry run protection, potential contacts for BMS integrating , sucton and discharge headers, pressure vessal 60 ltr capacity.

Supply, Installation, Testing & Commissioning of 6000 Lpd Water Treatment Plant with Reverse Osmosis Process with all mechanical work like piping, mechanical components as follows but excluding the electrical works and civil work. a) PAC off Chlorine Dosing system -1nos,Pressure sand filter FRP-1 no ,Activated carbon filter FRP-1no,

40 KLD Modular Membrane Bioreactor (MBR) based Sewage Treatment Plant, Design Flow KLD 40.0 LPH 2000.0 Type Fully-Automated, Design MLSS mg/L 6000.0 – 8000.0 Operating Hours h 24.0, Design Flexibility % 30 - 100 with transfer pumps, air blowers, medias, membrine, tube settlers and all connected pipe lnes and necessary power connections and cubicle control panel in all respect.

Incinerators with capacity of 150 kl per day include air pollution control equipment (e.g., fabric filters, scrubbers, electrostatic precipitators) to remove fly ash and gaseous contaminants

Providing, fixing, jointing and testing, heavy quality cast steel / Brass ball valve single/double piece designed of approved make, including flanges / unions, nuts, bolts, washers, etc. complete, as per I.S 5212 approved by the Engineer-in-charge for water supply lines of the following nominal bore (NB) size: 25mm diameter. Make:ZOLOTO/VTC/SANT

Supply, installation, testing and commissioning of 1200 LPD Solar Water Heater with Control panel with necessary controls, and other standard accessories as instructed by S-I-C.

Supply, installation, testing and commissioning of 1200 LPD Heat pump , 1200 ltr insulated SS tank with necessary connections, pressure guage, tempeature indicator, pressure release valves Control panel with necessary controls, and other standard accessories as instructed by S-I-C.

Supply, installation, testing and commissioning of Recirculation pump, Inline pump with SS body with 2lps @18 meter head with standard solinoid valves, necessary piping and other standard accessories as instructed by S-I-C.

Providing, fixing, jointing and testing, heavy quality cast steel / Brass Air Release Valve designed of approved make, including flanges / unions, nuts, bolts, washers, etc. complete, as per I.S 5212 approved by the Engineer-in-charge for water supply lines of the following nominal bore (NB) size: 25mm diameter. Make:ZOLOTO/VTC/SANT

Excavation for foundation/utility services upto 1.5 m depth including sorting out and stacking of useful materials and disposing off the excavated stuff with all lead and lift.(E) Hard Rock

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm. in depth consolidating each deposited layer by ramming and watering. (Ramping by manual or mechanical means)

Providing and fixing S.W. gully trap with C.I. grating brick masonry chamber and water tight C.I. cover with frame of 300mm x 300mm size (inside) with standard weight.(i) Square mouth traps.(B) 150mm x 100mm size P or R type (make-Local )

Constructing Brick masonry road Inspection chamber 450mm x 450mm x 775mm with horizontal grating complete. C. M. 1:6. Foundation concrete 150 mm thick in C. C. 1:4:8 of trap metal size 25 mm to 40 mm thick, inside cement plaster in C. M. 1:3 and cement pointing outside in C. M. 1:3 and ms gratings on top. Upto 1 Mt. depth from G. L. to pipe invert level incl. complete civil works but excl. cost of excavation and refilling, with cast in situ RCC slab in one single piece with fixing of CI-MH Frame and cover (incl cost of CI-MH Frame and cover) with 23 mm thick brick masonry wall in C.M.1:6. With precast slab in two parts 15mm. for rain water/storm water drainage

Construction of Manhole chambers(Inspection chambers) 600mm X 600 mm and depth 1.0 m in brick or bela stone masonry, locally available in C. M. 1:6. Foundation concrete 150 mm thick in C. C. 1:4:8 of trap metal size 25 mm to 40 mm thick, inside cement plaster in C. M. 1:3 and cement pointing outside in C. M. 1:3 and top cover of precast RCC slab 100 mm thick (with key hole in two parts, each with handles or MS Bar etc. complete as given size) Upto 1 Mt. depth from G. L. to pipe invert level incl. complete civil works but excl. cost of excavation and refilling, with cast in situ RCC slab in one single piece with fixing of CI-MH Frame and cover (incl. cost of CI-MH Frame and cover) with 23 mm thick brick masonry wall in C.M.1:6. With precast slab in two parts 15mm.

Extra over items above for every additional depth of 0.1M. of part thereof beyond 450mm depth for Brick masonry chamber.(i)

Providing and fixing C.I. cover with frame (Medium duty) 450x450 mm , total weight of cover and frame to be not less than 116 kg FOR SUMP TANKS

Providing and fixing C.I. cover with frame (Light duty) 450x450 mm , total weight of cover and frame to be not less than 38 kg for OHT

Supplying and fixing single headed internal hydrant valve with instantaneous Gunmetal/Stainless Steel coupling of 63 mm dia with cast iron wheel ISI marked conforming to IS 5290 (Type -A) with blank Gunmetal/Stainless Steel cap and chain as required : Make: Safeguard, Minimax, New Age

Supplying and fixing 63 mm dia, 15 m long RRL hose pipe with 63 mm dia male and female couplings duly bound with GI wire, rivets etc. conforming to IS 636 (type-A) as required : Make: Safeguard, Minimax, New Age

Stainless Steel (Grade 304)

Supplying & fixing 63 mm dia gun metal short branch pipe with 20 mm nominal internal diameter size nozzle conforming to IS 903 suitable for instantaneous connection to interconnect hose pipe coupling as required : Make: Safeguard, Safefire, Minimax, New Age

Supplying and fixing first-aid Hose Reel with MS construction spray painted in post office red, conforming to IS 884 complete with the following as required. 20 mm nominal internal dia water hose thermoplastic (Textile reinforced) type -2 as per IS: 12585 20 mm nominal internal dia gun metal globe valve & nozzle. Drum and brackets for fixing the equipmets on wall.Connections from riser with 25 mm dia stop gun metal valve & M.S. Pipe and socket. and tested to 1.2 MPA( 12 Bar pressure) installation brackets, complete in all respects including all accessories as required for complete installation. INLET PIPE CONNECTION FROM RISING MAINS TO HOSE REEL SHALL BE PROVIDED WITH GI HEAVY CLASS PIPES WITH UNIONS OR WITH READY MADE TYPE FLEXIBLE RUBBER HOSE IN STANDARD LENGTH, HYDRAULICALLY FITTED END CONNECTIONS ETC .Make: Monsher, Minimax, New Age

Supplying and fixing of fire brigade connection of cast iron body with gun metal male instantaneous inlet couplings complete with cap and chain as reqd. for suitable dia MS pipe connection conforming to IS 904 as required : Make: Safeguard, Safefire, Minimax, New Age

Providing, laying, testing & commissioning of 'B' class heavy duty G.I. pipe conforming to IS 1239 including welding, fittings like elbows, tees, flanges, tapers, nuts, bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required Note : Pipes up to and 50 mm dia shall be socket welded with DI fittings. For pipes inside the Fire pump room

25 mm dia

80mm dia

100 mm dia

150 mm dia

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required : Make : Leader/ Audco/ Zoloto

80 mm dia

100 mm dia

150 mm dia

Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required : Make : Leader/ Audco/ Zoloto

100 mm dia

80 mm dia

Providing, installation, testing and commissioning of stainless steel Y-strainer fabricated out of 1.6 mm thick stainless steel, Grade 304, sheet with 3 mm dia holes with stainless steel flange. Make : Leader/ Audco/ Zoloto

150 mm dia

Supplying and fixing air vessel made of 250 mm dia, 8 mm thick MS sheet, 1200 mm in height with air release valve on top and flanged connection to riser, drain arrangement with 25 mm dia gun metal wheel valve with required accessories, pressure gauge and paintingwith synthetic enamel paint of approved shade as required. Set

Supply, installation, testing and commissioning of Brass Air release valve, size 25mm with threaded inlet & provided with ball type float complete with all accessories required for complete installation. Make : Leader/ Audco/ Zoloto

Supply, installation, testing and commissioning of industrial type pressure switch having 1/4" BSP(F) connection IP:32 enclosure protection, phosphor bronze bellows as sensing element, SDPT contact system, switch rating 6A Inductive/lOA resistive 380 V AC, 0.2A Inductive/10A resistive 250V DC suit with ball valve etc. complete as required. Make: Infoss/

Providing, fixing, testing & commissioning of installation control valve of cast iron body, Brass/ bronze working parts comprising of water motor alarm, bronze seat clapper, clapper arm and hydraulically driven mechanical gong bell to sound continuous alarm when the wet riser/sprinkler system activates, pressure gauges, emergency releases, strainer, pressure switch, cock valve complete with drain valve and bypass, test control box, ball valves, MS pipe of required size, flanges, orifice plate, gasket etc of follwing sizes as required :

100 mm Dia

Supplying, installation, testing and commissioning of Electric driven Main Fire Pump suitable for automatic operation and consisting of following, complete in all respects, as required : (a) Horizontal type, multistage, centrifugal, split casing pump of cast iron body & bronze impeller with stainless steel shaft, mechanical seal conforming to IS 1520. (b) Suitable HP Squirrel cage induction motor, TEFC, synchronous speed 1500 RPM, suitable for operation on 415 volts, 3 phase 50 Hz, AC supply with IP 55 protection for enclosure, horizontal foot mounted type with Class-'F' insulation, conforming to IS-325. (c) M.S. fabricated Common base plate, coupling, coupling guard, foundation bolts etc. as required. (d) Suitable cement concrete foundation duly plastered with anti vibration pads.

1620 lpm at 56 m Head Set

Make : Kirloskar, Mather & Platt India Limited

Supplying, installation, testing and commissioning of electric driven pressurisation pump suitable for automatic operation and consisting of following, complete in all respects, as required : (Jockey Pump) Horizontal type, multistage, centrifugal pump of cast iron body and bronze impeller with stainless steel shaft, mechanical seal conforming to IS : 1520. Suitable HP squirell cage induction motor TEFC type suitable for operation on 415 volts, 3 phase 50 Hz AC supply with IP 55 class of protection for enclosure, horizontal foot mounted type with Class-'F' insulation, conforming to IS : 325. M.S.fabricated Common base plate, coupling, coupling guard, foundation bolts etc. as required. Suitable cement concrete foundation duly plastered and with anti vibration pads.

Pump – Pump Casing : C.I, Impeller- Bronze impeller

180 lpm at 56 m Head Set

Make : Kirloskar, Mather & Platt India Limited

Supplying, installation, testing and commissioning of diesel engine driven main fire pump suitable for automatic operation and consisting of following, complete in all respects, as required : (Diesel Driven Pump) Horizontal type, multistage, centrifugal pump of cast of iron body and bronze impeller with stainless steel shaft, mechanical seal conforming to IS 1520.Suitable HP, 1500 RPM water cooled with radiator, diesel engine conforming to relevant IS standard complete with auto starting mechanism, 12 /24 volts electric starting equipment, diesel tank, exhaust pipe extended upto 10 m outside pump house duly insulated with 50 mm thick glass wool with 1.0 mm thick aluminium sheet cladding, residential silencer, instruments and protection as per standard specification, stop solenoid for auto stop in the event of fault with audio indications, painted with post office red colour etc. as required. M.S fabricated, common base plate, coupling, coupling guard, foundation bolts etc. as required. Suitable cement concrete foundation duly plastered and with anti vibration pads. Suitable reinforced cement concrete pump foundation including cushy foot mounting, foundation bolts, washers as required. Engine panel, Sealed maintenance free batteries of 24 V, 88 AH, Exhaust pipe of required length with asbestos lagging, muffler, Day oil tank of 400 lts with first charge and manual oil pump set. No. of stage preferred - Single / Double,

The pump shall be of the following specifications: Discharge - 1620 lpm, Head - 56 m, Speed RPM -1450, Mover - Diesel engine driven, Material of construction, a) Impeller - Bronze, b) Casing - C.I., c) Shaft & Shaft Sleeve - SS-410, d) Bearing - Grease Lubicated, e) Seal & Make - Mechanical, Type of pump - End Suction.

1620 lpm at 56 m Head Set

Make : Kirloskar, Mather & Platt India Limited

Fabrication, supply, Insallation testing & commissioning of Electrical control panel of cubical construction, floor mounted type, fabricated out of 2mm thick CRCA sheet, compartmentalised with hinged lockable doors, dust and vermin proof, powder coated of approved shade after 7 tank treatment process, cable alley, inter connection with suitable size copper conductor cable/solid copper strip, having switchgears and accessories, mountings and internal wiring, earth terminals, numbering etc. complete in all respect, suitable for main fire pump, pressurisation pump & diesel pump set complete as per CPWD specification with following in coming and Outgoings, suitable for operation on 415V, 3 phase, 50Hz Ac Supply with enclosure protection class IP 42 as required :

Details of requirements given in specs.

Following provisions to be made in the fire panel:

Protection failure & control cabling.

Panel shall be interlocked in such a way when fire pump starts on pressure drop in the header, supply to working chiller A/c panel is disconnected.

Remote indication of ON/OFF/TRIP shall be provided through potential free contact.

Providing, fixing, testing & commissioning of 15mm dia quartzoid bulb type sprinklers of rating 68 degree centigrade with required accessories : working pressure 175 PSI (UL/FM approved) as required for complete installation as required. Make: Tyco/Viking/Sharp

Pendent Type bronze finish with C.P. brass rossett flange

Up right Sprinkler

Extended Coverage Side wall type sprinkler( apartment Inside)

Pre-assembled, ready to install, flexible connectors, stainless steel hose lengths: 1000mm,Mounting bracket , Maximum Working Pressure: 200 psi , Minimum Bend Radius UL Listed /FM Approved

Providing and fixing GI heavy duty 'B' class (IS: 1239 Part-1) including cutting, welding etc. and providing all fittings viz. Flanges. Bends,Tees, Elbow, Reducers, Clamps. Hangers etc. including cutting holes and chases in brick or RCC walls/slabs and making good the same to the approval of engineer/consultant complete including painting with one coat of primer and two or more coats of enamel paint of approved make and shade including steel work, GI pipe sleeve of suitable higher size shall be provided wherever the pipes are crossing the walls / floors and sealing the sleeves with glass wool in between & fire sealant compound at either end all as per Project Manager’s requirements including cutting holes and chases in brick, RCC work and making good the same to original conditions complete in all respects. Note : Pipes up to and 50 mm dia shall be socket welded with DI fittings.

25 mm dia

32 mm dia

40 mm dia

50 mm dia

65 mm dia

80 mm dia

100 mm dia

Supply, installation, testing and commissioning of electrically operated water flow switches (Vane type) dia 65 mm including tamper switch and accessories, complete with tap off socket arrangement as required, with potential free contact with 2 Nos. NO/NC including all accessories as required for complete installation. HD/ Honeywel

In 100 mm line

Supplying, installation, testing & commissioning response indicator on surface/ recess MS box having two LEDs metallic cover complete with all connections etc. as required

Supply, Installation, Testing and Commissioning of Fire alarm control panel capable of handling 99 devices / detectors per loop to meet the NFPA Standards and UL approvals. 2 loop Panel should be expandable, with a battery backup in normal condition and in alarm condition. The panel should be expandable.

Make: Honeywell/Edward/Essar/Cooper

Supply, Installation, Testing and Commissioning of Intelligent Addressable Heat Detector with base. The detector shall be suitable for both rate of rise and fixed temperature.

Make: Honeywell/Edward/Essar/Cooper

Supply, Installation, Testing and Commissioning of Intelligent Addressable Multi Sensor with optical smoke element and thermal element.

Make: Honeywell/Edward/Essar/Cooper

Supply, Installation, Testing and Commissioning of analogue addressable type Manual pull station at indicated locations with necessary termination as per the specifications and full ready for operation.

Make: Honeywell/Edward/Essar/Cooper

Supply, Installation, Testing and Commissioning of addressable sounder at different locations complete with all fixing accessories.

Make: Honeywell/Edward/Essar/Cooper

Supply and laying of 2C X 1.5 Sqmm Armoured copper conductor cable FRLS with all necessary saddles and other accessories. Make: Finolex/Polycab/Havells/KEA

Make: Finolex/Havells/Polycab

Supply, Installation, Testing and Commissioning of Short Circuit Isolator Module for isolating the affected segment of the circuit, allowing the remaining devices to continue operation.

Supplying, installation, testing & commissioning talk back slave station in surface/ recess suitable for operation on simplex mode complete with P.T.T. knob & speaker/ microphone enclosed in a M.S.(16 SWG)/ ABS box with break glass in front etc. complete as required.

Supply, installation testing and commissioning of 20mm. PVC Rigid Conduits conforming to IS and specification, on walls / ceiling / floor etc. complete with all accessories like junction boxes, collars, bends etc. Make: ISI Marked

Supply, install, test and commission 2C x 1.0 mm PVC cable. Make: Finolex/Havells/Polycab

Supply and installation of Weather proof Outdoor type hose cabinets fabricated from 14 SWG M.S. sheet with full glass door with locking arrangement (Water Proof), suitable to accommodate 2 nos.15 M long hose and 1 No branch pipe. Glass will be transparent Acrylic - 3mm thick. The cabinet shall be painted with coat of P O Red paint from outside and white paint from inside including all accessories as required for complete installation.(size shall be such that the above all items can be accommodated). (Double door type) as per industrial standards

Supplying, laying, fitting and fixing , testing and commissioning of under ground GI heavy duty 'C' class pipe confirming to IS 1239 The pipes shall have anti-corrosive wrapping coating and a wrapping treatment with pipe coat 4 mm thickness, after applying one or more coats of Asphalt primer. Rates shall include cutting, welding etc. bends, elbows reducers suitable for pipe joints, clamps and all other accessories including excavation of earth to sufficient depth to install the pipes, the pipes buried in ground excavation and refilling etc.as per the specification and as required complete as required for complete installation etc. including cutting holes in RCC walls/slabs and making good the same adequately supported on rigid supports duly painted as required complete in all respect including all up to building rising mains and for yard hydrants ,

100 mm dia

80 mm dia

Supply & installation of Pressure Gauge with 0-300 psi (0-21Kg/Sq.CM) range white background, black graduation scale with dual reading in Kg/Sq.CM & PSI, 1/4" BSPT bottom entry 100 MM dial, PHOSPHOROUS BRONZE bourden tube, brass moving parts, polished stainless steel case with positive seal against weather, moisture & dust, hardened glass, glycerine filled type with syphon tube and isolation cock,Make: Fiebig / H guru

Providing & fixing double flanged flexicon rubber expansion joint with unit control of standard length as per manufacturers specifications suitable for working pressure rated (PN16) and test pressure to be 150 % rated pressure of including rubber gaskets, flanges, nuts, bolts and washers complete as required

100 mm dia

80 mm dia

Supply and fixing Co2 type Fire Extinguisher of capacity 4.5 kg filled with Co2 Gas with control discharge mechanism ( squeeze grip type) fitted with Bend and Horn applicable on Class B and C class of fire. Manufactured and marked to IS 15683 with ISI marking and cylinders having the approval of Chief Controller of Explosives, and including all accessories as required for complete installation.

Supply and fixing of dry chemical powder type (DCP) fire extinguishers (ABC Type) of 4 Kg capacity, Pressurized with nitrogen, mfg. to IS:15683 with ISI mark fitted with pressure gauge, GM cap nozzle complete with initial charges and installation brackets and screws with ISI marks etc. complete as approved and instructed by the engineer in charge including all accessories as required for complete installation..

Supply and fixing emergency exit light fixture with battery back up unit, LED Lamps, indicating Fire Exit, recess / mounted type. 24hrs x 7days working conditional.

Supplying and installing of in position the various type of sign boards made out of 3mm thick "Opaque" PVC foam board with computer cut, PVC Non-reflective self adhesive vinyl painted foam board, complete with mirror fasteners. Size : 60cm x 15cm

Supply Installation, Testing & Commissioning of modular type Variable Refrigerant Flow/Variable Refrigerant Volume air cooled Outdoor units suitable for cooling and heating, having llhermetically sealed inverter type Scroll Compressor(s), minimum two compressors for above 14 HP modules,microprocessor based Controller, top discharge type condensing unit(s), with R 410 A Refrigerant, vibration isolators, with suitable foundation etc. complete as required. The unit shall deliver the rated capacity at AHRI Conditions and work even at 50°C ambient temperature without tripping. The unit shall be suitable to work on 400V +/- 10%, 3 Phase, 50Hz AC power supply. The unit shall be filled with first charge of the refrigerant and ready for use as required. The COP at AHRI conditions shall not be less than 3.1 and IEER not less than 6.5 .

Supply of VRV/VRF system with out door units & required matching indoor units with remote controls

Supply, installation, testing and commissioning of following minimum capacity VRV/VRF High wall type Indoor unit equipped with washable synthetic media pre-filter, fan section with low noise fan/dynamically balanced blower, multispeed motor, coil section with DX copper coil, electronic expansion valve, outer cabinet, cord less remote control, drain pan, necessary accessories etc., suitable for operation on 230 V ± 10%, 50 Hz, single phase AC supply, complete as required. The unit shall have automatic force shut down provision in case of fire on receiving signal from BMS System. The cooling capacity of indoor unit will be at air inlet conditions of 27 Degree C DB and 19 Degree C WB temperature.

1 TR Hi Wall Split Indoor Unit

1.6 TR Hi Wall Split Indoor Unit

2.5 TR Hi Wall Split Indoor Unit

Cordless Remote

Central Remote - Central Controller

Supply , Installation, Testing & Commissioning of Refrigerant Cu Piping with insulation

Supply , Installation, Testing & Commissioning of Drain Piping with insulation

Supplying, fixing, testing and commissioning of UPVC Class E condensate drain pipe with U trap, insulation & fittings up to drain line with necessary support and accessories

50mm Dia

32mm Dia.

25mm Dia

20mm Dia

Supply & Installation of Inline Centrifugal Extract Fans shall be with direct driven centrifugal fan, circular section, suitable for ceiling suspension/mounting. The units shall be complete with flexible duct connections at inlet and outlet. The motor shall be protected by thermal contact relay as protection against burn-out. as with all necessary accessories and supports

250 CFM,10MM ESP

450 CFM,15MM ESP

200 CFM,10MM ESP

100 CFM,10MM ESP

600 CFM,18MM ESP

Supply, installation , testing and commissioning of metal body wall mounted proppeller fan with necessary accessories and supports

Supply, installation , testing and commissioning of aluminium duct with corner pieces, nut& bolt, gasket, Joints to be sealed with sealents, with all necessary hi-tech support and accessories as per the site approved shop drawing and Site condition.(for OT1,OT2 , & OT TFA Ducting )

Supply, installation , testing and commissioning pre insulted duct with all necessary hi-tech support and accessories as per the site approved shop drawing and Site condition.

Supply, installation , testing and commissioning of GI volume control damper with corner pieces, nut& bolt, gasket, Joints to be sealed with sealents, with all necessary hi-tech support and accessories as per the approved shop drawing and Site condition.

Supply, installation , testing and commissioning of supply air aluminium powder coated diffuser with collar damper, withall necessary hi-tech support and accessories as per the approved shop drawing and Site condition.

Supply, installation , testing and commissioning of return air aluminium powder coated diffuser with outcollar damper, withall necessary hi-tech support and accessories as per the approved shop drawing and Site condition.

Supply, installation , testing and commissioning of supply air aluminium powder coated grille with collar damper, withall necessary hi-tech support and accessories as per the approved shop drawing and Site condition.

Supply, installation , testing and commissioning of return air aluminium powder coated grille without collar damper, withall necessary hi-tech support and accessories as per the site approved shop drawing and Site condition.

Supply, installation , testing and commissioning of aluminium powder coated louver withall necessary hi-tech support and accessories as per the site approved shop drawing and Site condition.

Supply, installation , testing and commissioning of class 'o' closed cell nitrile rubber insulation with self adhesive. Duct surfce to be cleaned before applying adhesive and joints to sealed with 3mm thick,5centimeter black tape.

13mm Thick

19mm Thick

Supply, installation , testing and commissioning of class 'o' open cell Acoustic insulation with self adhesive. Duct surfce to be cleaned before applying adhesive .

10mm Thick

Supply, installation , testing and commissioning of class 'o' closed cell nitrile rubber insulation for under deck with self adhesive.

13mm Thick

Supply, installation , testing and commissioning of HEPA filter,Plenum Construction : 1 mm Aluminium construction having Aluminium Square tube skeleton structure,Perforated diffuser: 1 mm Stainless Steel (SS-304) Inline Round Perfoaration : 5mm ø,12 mm Pitch,Filter fitment : Filter face seating on a self-leveling Poly Urethene compound formed on the Plenum structure,Thermal insulation : 19 mm thick Class "O" Nitrile insulation with aluminium foil lamination on exterior side,Duct connecting collar : No. of Duct connecting Collars -Based on user requirements Maximum Height : 225 mm,Volume control dampers : Aluminium Aerofoil Volume Control Damper Operable from the OT side without distrubing filter installation,Suspension brackets : SS "L" angle brackets for ceiling suspension of the Plenum, with all necessary hi-tech support and accessories as per the site approved shop drawing and Site condition. Plenum Size: 2350 (L) x 1740 (W) x 455 (H) mm (Excluding Thermal Insulation)

Supply,install,testingandcommissioningofstripheaterscomprisingthermostat,humidistat,safetythermostat,contactors,Controls&controlWiring.Minimumcapacityofstrip heaters shall be 2 KWx3Nos

OXYGEN SYSTEM (O2)

Supply, Testing and commissioning of Fully automatic Oxygen Control panel Model AMAZON -D with flow rate of 2100 LPM Fully complying with ISO 10524-2, ISO 7396-1:2007/HTM02-01 as per technical specification. (Make: Drager )

Oxygen Manifold

Supply, testing and commissioning of Oxygen Manifold - 2 banks x10 cylinders including Copper tail pipes. (Make:Drager)

Oxygen Emergency Manifold

Supply, testing and commissioning of Emergency Oxygen manifold 1 x 5 with IOX-14 high flow regulator (Make: Drager)

NITROUS OXIDE (N2O) SYSTEM

Supply, Testing and commissioning of Semi -automatic Nitrous Oxide Control panel with minimum flow rate of 2000LPM Fully complying with ISO 10524-2, ISO 7396-1:2007/HTM02-01 as per technical specification. (Make: Drager)

Manifold System N2O

Supply, testing and commissioning of Nitrous Oxide Manifold - 2 banks x 2 cylinders including Copper tail pipes. (Make: Drager)

Emergency Manifold N2O

Supply, testing and commissioning of Emergency Nitrous Oxide manifold 1 x 2 with IOX-14 high flow regulator. (Make: Drager)

CARBON DI-OXIDE SYSTEM

Supply, Testing and Commissioning of Carbon Dioxide manifold - 1 x 2 with IOX-14 High Flow Regulator. (Make: Drager)

MEDICAL AIR SYSTEM

Supply Installation, Testing and Commissioning of ANESTIWATA (Japan) Make Model BFT 75C- 9E 7.5 Hp Non - Lubricated Air Compressor Base frame mounted -24.43 cfm (692 Lpm) - 2 Nos. with all standard accessories.

Air Dryer system

Supply, Installation, Testing and Commissioning of TRIDANT Make Desiccant Air Dryer. Model : DRYSPELL PLUS 45 - 60 CFM

VACUUM SYSTEM

Supply, Installation, Testing and Commissioning of. ANEST IWATA Make Vacuum Pump Model:BVLS 50 DE - 5HP - 2 Nos with 1000 Ltr Vacuum Receiver tank - 1 No, Vacuum switch - 2 No., DOL starter - 2 No, 5 HP Motor - 2 No. with inter connecting pipes

COPPER PIPING Supply, installation testing and commissioning of Copper pipe: Per Mtr. It must comply with EN 13348 as per technical specifications. Make: Mexflow

MEDICAL GAS OUTLETS Supply, Installation, testing and commissioning of DIN Gas Outlets meeting requirements of EN ISO 9170-1 Make: Drager

O2 Outlet with probe

N2O Outlet with probe

Air 4 Outlet with probe

Air 7 Outlet with probe

CO2 Outlet with probe

Vacuum Outlet with probe

Anaesthesia Gas Scavenging System Outlet (AGSS) Ventury type with probe (Make: Drager)

AREA VALVE BOX Supply, Installation, testing and commissioning of Area Valve Service fully complying with ISO 7396-1:2007 (Make: Aktive Technologies)

2 Gas With Valves (15/22)

3 Gas With Valves (15/15/22)

4 Gas With Valves (15/15/15/22)

6 Gas With Valves (15/15/15/15/15/22)

AREA ALAM PANELS Supply, Installation, testing and commissioning of Digital Area Alarm Service fully complying with ISO 7396-1:2007 (Make Aktive Technologies)

Medical Gas Area Alarm Digital 2 Gas

Medical Gas Areal alarm Digital 3 Gas

Medical Gas Area Alarm Digital 6 Gas

BALL VALVES Supply, installation, testing and commissioning of Ball Valves, complying with HTM 02-01, as per technical Specifications. Make: UN Med

Double Arm Pendant (Surgical Pendant) Supply, Installation, testing and commissioning of Surgeon Pendent with Double Arm, provision for Medical gas Terminal units as per consultant drawing,330 degree angle rotation of column and arm, with Friction break as standard for arm system, 3shelves. Provision for 12 nos Electrical and 4 data Points. Pendant Console Consist of Three Seperate compartments One for Medical gas and two for Electrical sockets and cables installation as per International standards (Make: Drager / Maquet / Stark Storme )

Single Arm Pendant (Surgical Pendant) Supply, Installation, testing and commissioning of Surgeon Pendent with Single Arm, provision for Medical gas Terminal units as per consultant drawing,330 degree angle rotation of column and arm, with Friction break as standard for arm system, 3shelves. Provision for 12 nos Electrical and 4 data Points. Pendant Console Consist of Three Seperate compartments One for Medical gas and two for Electrical sockets and cables installation as per International standards (Make: Drager / Maquet / Stark Storme)

Rigid Pendant Rigid Pendant Vertical type with Provision for Medical Gas Outlets and Electrical Sockets with 1 Monito r stand

Bead Head Panels (BHU) Supply, Installation, testing and commissioning of Bed head panels with Medical gas Terminal unit provisions as per tender drawing, Provision for Electrical and data points as per consultant specification. (Make: Drager / Stark Storme) 4 Feet Long

ACCESSORIES (Make: GHL)

Oxygen BPC Flowmeter with Humidifier Bottle

600 Ml Wall Suction Unit

Theatre Suction Unit with 2 x 2000 ml Bottles

Medical Oxygen Generation Plant

1. Compressed Air Station

Modular rotary screw compressor with refrigeration dryer & air receiver, equipped with the followings: from FS CURTIS

a) Air compressor

b) Refrigeration air dryer

c) Air filtration system

d) Air tank :1500L

2. OXYGEN PSA GENERATOR

a) 2 PSA sieve beds

b) 1 monitoring system CPU Controller with digital screen

c) 1 separate oxygen receiver equipped for oxygen service

d) 2 air inlet filters (25 μm and 0.1 μm)

e) 1 oxygen outlet filter

* Flow : 10.5 m3/h at purity 93% + 3%

* Pressure : 4.5 to 6 bar-g

3. OXYGEN BUFFER

a) Vertical configuration

b) Capacity : 1000 L

OT TABLE

• Table type: fully electric • Height adjustable range: 750mm to 1000mm • Trendelenberg : 30 degree • Maximum patient load: 200 kgs • Table length: 1930mm • Table width: 533mm • Trendelenberg reverse: 25 degree • Lateral tilt: left :20 degree/right :20 degree • Back rest: up:80 degree/down:25 degree • Leg rest:up:15 degree/down:90 degree • Head rest :up:20 degree/ down:60 degree

STAAN/CONFIDENT/AMSCO

OT LIGHT

• Double doom • Light source type: L.E.D. • Color temperature: 4300 K • Intensity: 1,60,000 Lux • Focus diameter: 15-20 cm • Led lifetime: 50,000 hours. • Light head diameter: 53cm • Control unit: SMPS • Color rendering index: 93 • No of LEDs: 63

DR MAACH/STAAN/STRYKER

SPOT LIGHT

• Heavy base with low centre of gravity. • Single light head with LED lights in cluster. • Articulating arm between light and base stand. • Base with 5 anti-static swivel castors in a star formation. • At least two castors have been equipped with brakes. • Minimum 14 cm fixed focus field of view. • Minimum illumination of 60,000 lux at 0.5m. • Minimum colour temperature between 4,000°K. • Minimum colour rendering index (CRI) of 95. • Minimum LED life more than 40,000 hours. • Floor to light height adjustable to include at least range of 1.1 m to 1.75 m. On/off switch. • Power requirements: 100 - 240 Volts - 50/60 Hz.

STAAN/FLORIX/VANSAARI

ANESTHESIA MACHINE

• Display size 18.5 inch • Display type Color LCD with capacitive touch screen • All setting and alarm parameters(including Breath rate, I/E ratio, Tidal volume, Minute volume, PEEP, MEAN, PEAK, PLAT, and O2 concentration, EtCO2, N2O, Aesthesia gas concentration, BIS) • Graphic waveforms : Pressure, Flow, Volume, CO2, O2, Anesthetic gas, N2O, BIS, Pes, Ptp • Display content Volume exchanger indicator, gas supply pressure, AGSS status • Spontaneous ventilation/Bypass • Volume Control Ventilation (VCV) with PLV function

G.E./MINDRAY/SKANRAY

CENTRALISED MEDICAL GAS SYSTEM

PULSE MEDITECH, OXYMEDILAB, DRAGGER

SYRINGE PUMP

AKAS/MINDRAY/HAWKMED

INFUSION PUMP

• Accuracy ≤ ±5% • Mode : Rate Mode (drip mode), Body Weight Mode, Time Mode, Sequential Mode, Loading Dose Mode, Micro-infusion Mode, Ramp Mode • Flow rate 0.1 - 2000ml/h • Increment the minimum increment is 0.01ml/h • Preset volume(VTBI) 0.1 - 9999ml (increment: 0.1ml) • Preset time 00:00:01-99:59:59, adjustable • Standby time 00:01-99:59 • Accumulated volume 0.1-9999 ml • KVO 0.1-30ml/h, default is 0.5ml/h • Purge rate 0.1-2000ml/h • Bolus rate 0.1-2000ml/h (automatic or manual) • Occlusion detection 14 Levels are adjustable

AKAS/MINDRAY/SMITH MEDICAL

MULTIPARAMONITOR

• 12-lead: I, II, III, aVR, aVL, aVF, V1 to V6 • Sweep speed 6.25 mm/s, 12.5 mm/s, 25 mm/s, 50 mm/s • Gain x 0.125, x 0.25, x 0.5, x 1, x 2, x 4, • SpO2range 0 to 100 % • SpO2accuracy Adult/Pediatric: ± 2 % (70 to 100%) • Neonate: ± 3 % (70 to 100%) • Perfusion indicator (PI) • PR range 20 to 300 bpm (from SpO2) • 30 to 300 bpm (from NIBP) • PR accuracy ± 3 bpm • Temp range 0 to 50 °C (32 to 122 °F) • Temp accuracy ± 0.1 °C or ± 0.2 °F (without probe) • Temp resolution 0.1 °C • Operation mode Manual, Auto, STAT, Sequence • Parameters Systolic, diastolic, mean • Max measurement time Adult/Pediatric: 180 s, Neonate: 90 s

BPL/SKANRAY/SCHILLER

SURGICAL DIATHERMY

• Microprocessor controlled • Smart feedback system • Pre-defined programs • Monopolar & bipolar modes • Soft, Swift, Force & Spray coagulation • Dual output for monopolar coagulation • Split patient plate indicator • Bipolar coagulation with auto start • Automatic power regulation • quality monitoring system

ALAN/VALLEYLAB/COVIDIEN

PORTABLE X-RAY

GE/SKANRAY/ALLENGERS

ANESTHESIA PENDENT

Anesthesia Pendent with Single Arm, Terminal units as per consultant drawing,330 degree angle rotation of column and arm, with air break as standard for arm system, 2shelves ,IV pole with arm- 1no.,Provision for 12 nos Electrical and 4 data points.

SURGERY PENDENT

Surgeon Pendent with Double Arm , Terminal units as per consultant drawing,330 degree angle rotation of column and arm, with air break as standard for arm system, 3shelves.Provision for 12 nos Electrical and 4 data points.

• Microprocessor controlled • Smart feedback system • Pre-defined programs • Monopolar & bipolar modes • Soft, Swift, Force & Spray coagulation • Dual output for monopolar coagulation • Split patient plate indicator • Bipolar coagulation with auto start • Automatic power regulation • quality monitoring system

ALAN/VALLEYLAB/COVIDIEN

• Ergonomic Touch Panel 10” Touch Panel with Tilt & Swivel enables better viewing for the operator • Live Fluoro – Live & LIH Fluoroscopy Image display at Control Panel for accurate C-Arm positioning with no retakes • Access to Laser Aimer operations with Pointer display on Live/ LIH Image • Digital Preview Collimation from touch control panel without X-Ray exposure helps in dose reduction • Automatic dose Control to adjust system’s exposure automatically as per the body region. • Low Rate Pulsed Fluoroscopy available for significant dose reduction Digital Image Rotation from Control Panel

PHILIPS/SKANRAY/GE

LAPAROSCOPY UNIT

• In-line insufflator gas warming capability is provided through one or two parts. • A stop safety feature prevents intra-abdominal pressure from exceeding 15 mmHg. • A TAP feature acts as an independent abdominal pressure monitoring line. • Simple front panel design is arranged in three distinct sections: one for gas supply, one for gas flow rate control and one for abdominal pressure regulation. All instruments are 330 mm working length • Complete instrument consists of one each: Handle, Housing Tube, Inner Assembly, Outer Tube and Nose Cap • Modular design • Ergonomic handle • Permanently sharp, economical scissors ensured by replaceable scissors tips • All graspers have a ratcheted locking mechanism • Dual action graspers can be rotated through 360° • Insulated shaft for additional safety in an electrosurgical environment

STRYKER/SMITH&NEPHEW

OPERATING MICROSCOPE(ENT/OPHTHAL)

LABOMED/CARL SEIZZ

PHACO MACHINE

APPASAMY/OERTLI

• Microprocessor controlled • Smart feedback system • Pre-defined programs • Monopolar & bipolar modes • Soft, Swift, Force & Spray coagulation • Dual output for monopolar coagulation • Split patient plate indicator • Bipolar coagulation with auto start • Automatic power regulation • quality monitoring system

ALAN/VALLEYLAB/COVIDIEN

MULTIPARAMONITOR WITH IBP, ETCO2

• 12-lead: I, II, III, aVR, aVL, aVF, V1 to V6 • Sweep speed 6.25 mm/s, 12.5 mm/s, 25 mm/s, 50 mm/s • Gain x 0.125, x 0.25, x 0.5, x 1, x 2, x 4, • SpO2range 0 to 100 % • SpO2accuracy Adult/Pediatric: ± 2 % (70 to 100%) • Neonate: ± 3 % (70 to 100%) • Perfusion indicator (PI) • PR range 20 to 300 bpm (from SpO2) • 30 to 300 bpm (from NIBP) • PR accuracy ± 3 bpm • Temp range 0 to 50 °C (32 to 122 °F) • Temp accuracy ± 0.1 °C or ± 0.2 °F (without probe) • Temp resolution 0.1 °C • Operation mode Manual, Auto, STAT, Sequence • Parameters Systolic, diastolic, mean • Max measurement time Adult/Pediatric: 180 s, Neonate: 90 s

MINDRAY/SKANRAY/PHILIPS

ANESTHESIA WORKSTATION WITH VAPOURISERS

• Display size 18.5 inch • Display type Color LCD with capacitive touch screen • All setting and alarm parameters(including Breath rate, I/E ratio, Tidal volume, Minute volume, PEEP, MEAN, PEAK, PLAT, and O2 concentration, EtCO2, N2O, Aesthesia gas concentration, BIS) • Graphic waveforms : Pressure, Flow, Volume, CO2, O2, Anesthetic gas, N2O, BIS, Pes, Ptp • Display content Volume exchanger indicator, gas supply pressure, AGSS status • Spontaneous ventilation/Bypass • Volume Control Ventilation (VCV) with PLV function

MINDRAY/GE/SKANRAY

DEFIBRILLATOR

Waveform: Biphasic truncated exponential waveform , with impedance compensation Energy accuracy: ±2 J or 15% of setting, whichever is greater, into 50 Ohm Charge Time: Less than 3 seconds to 200 Joules with a new, fully charged battery Less than 7 seconds to 360 Joules with a new, fully charged battery Shock Delivery: Via multifunction defib electrode pads, or paddles Patient Impedance Range: 25 to 300 Ω (External defibrillation) Manual Mode Output Energy: 1,2,3,4,5,6,7,8,9,10,15,20,30,50,70,100,150,170,200,300,360 J Synchronous Cardioversion: Energy transfer begins within 60ms of the QRS peak Energy transfer begins within 25ms of the External Sync Pulse

BPL/SKANRAY/MINDRAY

TORNIQUET

DIAMOND

FULLY AUTOMATIC HORIZONTAL STEAM STERLISER

TUTTUNEUR/GETTINGE/MMM

HORIZONTAL STEAM STERILISER

YORCO/OSE

ETO STERILISER

PLASMA STERILISER

JOHNSON& JOHNSON

ULTRASONIC CLEANER

Freestanding ultrasonic washer for surgical instruments to process up to 16 lumened devices, or up to 35 lbs. per cycle* Automated dosing and delivery of chemistry Simple operation with touch screen control that clearly displays cycle status

UNIDENT/VEVOR

INSTRUMENT DISINFECTOR

50% more throughput compared to standard single chamber washers Uses as low as 31 gal. water/cycle; Process up to 300 DIN trays/8-hour day

DRYER UNIT

SEALING MACHINE

• Stainless steel material • Sterilization pouch packing • Capacity of 10M/Min

SEAPACK

SITC OF Pre‐Fab Wall Panel: Stainless Steel Grade 304 Panel : The Pre‐fabricated modular construction is designed and constructed for exact size, easy field installation and future disassembly, enlargement, or relocation. The operating room will be constructed from Pre‐fabricated Panel of 1.2 mm or more thick Stainless Steel Grade 304 sheets, with a 12 mm thick backing of gypsum board

SITC OF Substructure Steel Assembly : Substructure elements of 1.5 mm thick GI extending from the finish floor to ceiling slab to make the wall panels free standing. Suitable substructure in GI for mounting wall panels along walls, with cross members to support equipment's flush mounted in to the wall panels. Substructure will also have provision for routing electrical wiring and gas Pipeline.

SITC OF Pre‐Fab Ceiling: Stainless Steel Grade 304 Panel : The Pre‐fabricated modular construction is designed and constructed for exact size, easy field installation and future disassembly, enlargement, or relocation. The operating room ceiling will be constructed from Pre‐fabricated Panel of 1.2 mm or more thick Stainless Steel Grade 304 sheets, with a 12 mm thick backing of gypsum board. Suitable grid structure suspended from the ceiling slab should be provided to support the ceiling panels to the required height, and also provide for easy routing of electrical conduits, gas pipelines and bio air‐conditioning ducts.

SITC OF Antimicrobial Coating: Filling of all Joints and cavities with metallic Epoxy Filler and Sanded Flush to provide a joint less finish and then sprayed with a water based liquid plastic aseptic and self sterilizing wall coating system to a d.f.t. of 300microns with primer.

SITC OF Antistatic Conductive/ Dissipative Flooring: Seamless with perfectly curved flush‐covings, resistance to mechanical stresses and dynamic loads and having conductive protection characteristics, 2 mm thick, washable

SITC OF Hermetically Sealing type of Manual Sliding / Swing Door having thickness of 40‐48mm of size 1500 X 2100 mm single / dual leaf with PUF core sandwiched between Antimicrobial High Pressure laminates (HPL), with viewing window of size 300 X 300 mm. The door leafs hung on extruded heavy duty aluminium alloy extrusion Doorframe for single side swing Doors, Sliding Door leafs runs on (nylon wheels) within an extruded heavy duty aluminium alloy extrusion track / frames, for smooth effortless sliding with the help of handle.

SITC OF Microprocessor based Electronic Automation (Operator ) for Manual Door for controlling the direction of movements, the acceleration and speed of the door, with a low noise level pulse generator motor. It includes a photocell for users safety. (For sliding door)

DND INFRA PRIVATE LIMTED