Interior, Furnishing, Renovation, Electrification and Other Allied works for in P.V.T.G. Skill Development Centre at SHIVPURI, DINDORI, MANDLA, SHAHDOL AND TAMIYA(CHHINDWADA) (M.P.)

Amount

Providing & Fixing of 24-Port Data Switch of [Managed Layer-2 with 2-Giga Ports (10/100/1000) ] Make: D-link/Cisco/Netgear Or Equivalent

Providing and Fixing of Freestanding Gooseneck Mic with base for podium having back electret condensor microphone element ,Hyper Cardioid polar pattern,LED status display and with programmable button for Push to Talk or Push to Mute functions having ,frequency response 50Hz-20kHz ,sensitivity 5.5mV/Pa,clipping level >130dB SPL ,output impendence 200 ohm. Make : Electrovoice / Beyer Dynamic / Shure / AKG Or Equivalent

Providing ad Fixing of Conferencing Processor with AEC 12 Analog Inputs (with 48v Phantom Power per Channel) 8 Analog Outputs Configurable Signal Processing 12 Channels of AEC Processing with Auto Gain Control and Noise Cancellation Rich Palette of Processing and Logic Objects 48 Channel, Low Latency, Fault Tolerant Digital Audio Bus Clear Front Panel LED Indication Bi-Directional Locate Functionality 12 Control Inputs and 6 Logic Outputs for GPIO Integration (Audio and Video Conferencing Compatable) Make : (BSS/EV/Shure) Or Equivalent

Providing and Fixing of high Quality Signal Microphone Cable Jacket PVC, ø 8.80 mm, marine blue Shield No. 1 Bare copper wires (0.10 mm), 100% coverage Shield No. 2 Bare copper wires (0.10 mm), 100% coverage Layer Polyester nonwoven thermally bonded, both sides alum. coated Separation Filler material viscose Conductor shield layer Polyester nonwoven thermally bonded, both sides alum. coated Cond. copper shield Bare copper wires (0.10 mm), 100% coverage Isolation Cellular PE, ø 2.00 mm, 4 different colors Conductor Stranded bare LCOF copper wires, 64 x 0.10 mm (4x) (0.50 mm²

Providing and Fixing of of System Interconnects

SITC of 4200 Ansi Lumens Projector with technology : Digital Line Processing Min Brightness : 4200 Ansi Lumens Min Contrast Ratio 3000:1 Image Size 0.78 - 9.38m (30.79" - 369.43") Diagonal 4:3 Native resolution : XGA (1024 x 768) Video Compatibility : PAL, Secam 576 i/p NTSC 480 i/p, HD 720p/1080i/1080p Aspect ratio Native 4:3 Compatible 16:9 Power supply 100 - 240V, 50-60Hz. (Make : Optoma / Epson) Or Equivalent

Audio Equipment Rack : Providing & Fixing of pre-wired standard 19”Audio Equipment Rack made of Die extrusion aluminum with front /rear doors, power panels, casters wheel and cooling fan etc suitable enough to accommodate all Rack mounted Audio equipment. 18U

Supply, Installation, Testing & Commissioning of Mounting arrangement for projector.

Supply, Installaton, Testing & Commissioning of manual Projector Screen - 8 x 6 Matt White, 220 V Make : Liberty/Suvira/Elite Or Equivalent

Supply, Installation, Testing & Commissioning of Wi-Fi Router, Simultaneous dual band 2.4 GHz & 5 GHz, Five (5) 10/100/1000 (1 WAN and 4 LAN) Gigabit Ethernet ports with auto-sensing technology, 802.11 b/g/n/ac Supported as per technical specification.

Providing, Laying and Installation of HDMI Cable. 15 Mtr

Providing & Laying of 2-core 2.5 sq. mm. Shielded Twisted pair loudspeaker cable. Make : Liberty/Finolex/Lapp/Krystal Or Equivalent

Handheld type Cordless Microphone : Providing & Fixing of professional Handheld / Lavalier type Cordless Microphone.

Providing and Fixing of Architectural adaptor plate with VGA and HDMI with 15-Pin HD, HDMI & stereo Audio Passive wall Plate. Make : Aten / Cypress / Kramer Or Equivalent

Executive Table with Side Table -SPECIFICATION :-1800mm W x 900mm D x 750mm H Top made of 36 MM thick BSL Particle Board and short sides duly sealed with PVC edge banding of 2MM thickness. Base made of 36 mm thick BSL Particle Board with levelers.Top supporting rail of 25 mm thick BSL Particle Board.Side runner of size 1000mm W x 400mm D x 634mm H made of 18 mm thick BSL particle board and top 36 mm BSL particle board. Side runner shall have one cupboard. Pedastal with three drawers shall be provided of 450mm width

Executive Table with 3 drawer- Table-1200x600 With 3D Pedastal 400x450x640 ,Table Top & Gable End Made of 25mm Thick Prelam Particle Board and Modesty Made of 18mm Thick Prelam Particle Board in swede FinishAll open Edge Covered with 2 MM Thick PVC Edge Band and non Visible edge covered with 0.8mm thick pvc edge Band.

Office Table- Table Size-900x600X750 With Single Drawer,Top Made of 18 mm thick Prelam Particle Board all open Edge Covered with 2 mm Thick PVC Edge Band & Understructure Made of Squire Tube of Size OD 25X25x1.2 mm.Complete metal understructure will be Powder Coated after 9 Tank Pretreatment.overall product as per image

Teacher Table- Size :-W-900mm x D-600mm x H-750mmPost Formed Table top: made up of 25mm thick plain MDF board ISI mark post formed laminated 0.6mm thick.3. Lipping: The Side edges of top shall be sealed with tape 2mm thick edge bands by hot process.4. Frame Structure: Made up of Prime quality CRCA rectangular tube 25x50x1.2mm thick welded to Press formed steel column 95mm x 25mm x 1.0mm thick covered with folding panel in different colour, made of prime quality CRCA sheet 65mm x 23mmx0.6mm thick. Upper tie members & foot rest, to join two leg assemblies, made of press formed prime quality CRCA sheet 50mm x 25mmx1.0mm thick OR rectangular CR tube of same size.5. Upper Front Panel: Press formed point embossed Prime quality CRCA sheet of H-150mm x D 100mm x 0.6mm thick in different colour shade. This panel also serve as cable duct to run electric/data cables.6. Lower Front Panel: Made up of prime quality CRCA sheet 380mm wide x 0.8mm thick square perforated (at 35mm pitch approx.) matching with structure colour.7. Finish: All steel components should be epoxy powder coated after seven tanks anti corrosion pretreatment of surface

CONFRENCE TABLE-Overall dimension 6400x1600x750 TOP made of partical board 25 MM thick PLPB modesty and gable end 18 mm thick PLPB with 2 mm PVC EDGE banding with cebal manager

Computer Table 4 Parson Back To Back- Overall dimension of the table is L1800 x W1200 x H750mm. The top shall be made of 25mm PLPB board with 2 mm pvc edge banding The each table of 1800 mm length 3. One CPU TROLLY. A key board tray & Key board shall be mounted on telescopic channel.5. The rest of the table shall be made of 18mm thick ISI mark PLPB6. The edge banding shall be done by 2mm thick PVC tape by hot pressed machine of Matching colour

Reception Table- Size:-1500(W) X 600(D) X 750/1000(H)Top panel of 25mm thick Prelaminated Particle Board• All panels made from 18/25mm thick relaminated Particle/MDF Board • All open edges are covered with 2mm thick PVC Edge Banding and all nonvisible edges are covered with 0.8mm thick PVC Edge Banding

Magazine Display Rack- Overall dimension shall be W1200 x H 1500 x D 550mm. Rack shall be made of post form 18mm MDF board ISI marked and 0.6mm laminate duly pasted on it. Aspring coil shall be provided on each shelf to hold the magazine upright.

High Back Revolving Chair- Overall size : - Total Height: 1000-1100mm Seat Height:425-525mm, Depth: 600mm and width: 530mm.2. Seat size 475x465 mmBack size 475x585 mm3. Material: Seat made up of 12mm thick hot pressed plywood, with 40-50 density polyurethane moulded foam min. 50mm thick. The back made of glass filled 30% nylon with nylon mesh fabric.4. The adjustable armrest made of glass filled 30% nylon & top made of polypropylene with eight different position locking.5. Castors: The twin wheel castors should be injected moulded in black Nylon.6. Pedestal Assy: The pedestal shall aluminium die casted as ohwn in photograph. width 700mm7. Upholstery: The seat and back are to be covered with superior quality Leatherite fabric. 8. Mechanism – The syncro tilt mechanism with single position lock

Executive mid back revolving chair- SPECIFICATION 1. Size: - Total Height: 985 mm Seat Height: 480mm Min.-580 Max.. Depth: 440mm and width: 480mm Seat size 465x440 mm Back size 450x400 mm 2. Material: Seat made up of 12mm thick hot pressed plywood, with 40-50 density polyurethane moulded foam 50mm thick. The back made of glass filled 30% nylon with nylon mesh febric .3. The adjustable armrest made of glass filled 30% nylon & top made of polypropylene with eight different position locking.4. Castors: The twin wheel castors shall be injected moulded in black Nylon.5. Pedestal Assy.: The pedestal shall be aluminium die casted as shown in photograph 6. Upholstery: The seat and back are to be covered with superior quality latherite fabric.7. Finish: steel are to be powder coated after seven tanks anti corrosion pretreatment of surface. Coating thickness 50 micron.8. Tilting mechanism with single position locking.

Computer chair - Overall Dimension Seat -300mmdia round seat made from 12 mm thick plywood cushion withhigh dencity pu fom upholstery with leatheritee base ms powder coated

Teacher Chair-Overall Dimension: W535 x D 595 x H 820mmSeat height 460mm2. Seat size: 420 x 420mm approx.3. Back size: 420(W) x 270mm (H) approx.4. Material: The seat and back shall be made up of 10mm thick hot pressed water resistance commercial plywood, upholstered with fabric and moulded polyurethane foam (40mm thick with density 40-50)5. Tubular Frame: The main frame shall be cantilever type reinforced at the bends to give cushioning effect and added strength and made of dia 25mm x 1.8mm to 2.0mm CR tube.6. Tubular Armrest: Shall be made in twin tube form and made from dia 16mm x 1.6mm CR tube.7. Finish: All steel components shall be Epoxy powder coated after seven tanks anti corrosion pretreatment of surface

Chair With Table- Overall Size: - Total Height: 825mm. Seat Height:460mm.Tablet Ht. 665mm Depth: 570mm. and width: 550mm.Seat Size 490 x 460 mmBack Size 485 x 465 mm 2. Cantilevered understructure made of Dia 25mmx1.8 mm round steel tube, reinforced at proper places and bent at appropriate angle and radius. 3. Seat – mounting made of steel-flat 38x5.4. Foam & moulded cushion on hot pressed 12mm thk. ply supported by steel tubular frame 5. Steel Tnuts inserted into ply for rigid fastening.6. Moulded-cushion 45mm thk with density 40 seat & back contoured for proper lumbar –support& rested back. 7. PVC beading all around the seam of tapestry.8. Writing tablet made of . layered pre laminated particale board (18mm thick) ISI Markedof size 580mmx280mm.9. Finish: All steel components shall be epoxy powder coated after seven tanks anti corrosion pretreatment of surface.

3 Seater Visitor Bench SS- Visitor bench shall be suitable for three persons. 2. Size: 1750mm (L) x 820mm (H) x 720mm (W) and Seat height 390mm from ground level. 3. Material: Complete visitor bench shall be made of stainless steel grade 304.4. Seat & Back: Each seat & back shall be made of 1.6mm thick SS sheet uniformly perforated in single piece. 5. Base Beam: Made of stainless steel grade 304 of size 60x40x2.0mm thick in single piece.6. Arms & Legs: Shall be made of stainless steel grade 304 pipe not less than 2.00 mm thick.7. Wherever details not mentioned, the material used shall be of high quality for strengthen & better look of the product, as per standard practice. 8. The seat shall be fitted on the base with the help of brackets. 9. Fasteners shall be used of SS only

Three Seater Sofa- 1975mm(L) x 910mm(D) x 870mm(H), Arm height 490mm. a) Structure - Sofa structure is to be made of 45x 28mm finished teak wood section, the structure shall be provided with flat helical springs.b) Seat - Sofa seats is to be made with 90mm thick 40 density PU foam with toping of super soft foam. c) Back - Back is to be made with 50 mm thick 32 density PU foam with toping of super soft foam.d) Arm - Arm structure is to be made with 120 x 28mm teak section for front, top and bottom. Arm back is to be made with 45 x 35mm teak wood section. Arms are to be covered with 35 mm thick 28 density PU foam with toping of 20 mm super foam.e) Synthetic leather/fabric shall be used for upholstery as per approval of user deptt

Podium- Overall dimension shall be H 1200 x W750/600 x D 450mm.2. Podium shall be made of 18mm thick MDF board ISI marked.3. The podium shall be post formed. 4. The base shall be of 25mm commercial ply ISI marked.5. Laminate shall be used 0.6 for post form.6. One shelf shall be provided below the top. 7. The self shall be mounted on telescopic channels8. Bottom shelf shall be 70mm above base 9. The base shall be fixed on post form strips of 150mm width. 10. The edge banding shall be done by 2mm thick PVC tape by hot pressed machine of Matching colour.

Dual Deak Two Seater - Overall Dimensions: W1060mm x D 940mm x H - 760/450mm 2. Side frame structure: Made of Prime quality CRCA pressed form section 165 mm x 25mm x 1 mm thick welded to 25 mm x 50 mm x 1.2 mm thick CRCA tube as shown in photograph. Seat and back side frame structure also made of Prime quality CRCApressed form section 165mm x 25mm x 1mm thick welded to 25mm diameter x 1.2 mm thick CRCAtube. All 8 nos. horizontal supports are 25mm x 25mm x 1.2 mm thick CRCAtube. 3. Front panel cum tray shall be made of prime quality 0.8 mm thick CRCA sheet of H 150mm x W1012mm x D300 mm width middle partition and side stiffeners of MS CRCA tube. One vertical support of square tube must be provided at centre of tray and reinforcement at sides of the tray shall also provided. Front face must be embossed (dotted) as shown in photograph. 4. Additional front panel prime quality 0.8 mm thick CRCA sheet of size H 150mm x W1012mm x D 25mm with square perforation as shown in photograph. 5. Desk Top, seat and back shall be made of ISI marked PLPB board duly post formed with 0.6mm thick laminate on it of 18mm thick and all edges must be sealed with 2mm thick PVC edge banding tape with hot melt glue on edge banding machine. Edge band must be trimmed on edges and corner, sizes are as below: -1. Seat: W1060mm x D 300mm,2. Desk Top: W1008mm x D 450 mm, 3. Back: W1060 mm x D 150 mm6. Desk Top, seat and back must be fitted with frame with M6 sunken head bolt. Minimum 6 bolts must be used to fix one section.7. Hooks made of 4 mm diameter MS wire must be provided on inner side of vertical pressed formed steel section on both sides.8. All steel components must be powder coated after 7 tanks pretreatment process

Corner Table- Overall Size: 600 x 600 x 480 mm a) Legs shall made out of 62x62 mm teakwood section as per photograph. b) Top rail shall be made of 62x22mm as per photograph. c) Top shall be made of 18mm veener faced MDF board. d) Teak wood beading of 18mm shall be fitted as per approval. e) Polish- PU polish shall be done.

Center Table- Overall Size: 1200 x 600 x 450 mm a) Legs shall made out of 75x75 mm teakwood section as per photograph. b) Top rail shall be made of 70x22mm as per photograph. c) Top shall be made of 18mm veneer faced MDF board. d) Teak wood beading of 18mm shall be fitted as per approval. e) Polish- PU polish shall be done

Steel Almirah 1980x915x485,Almirah Body Made of CRCA sheets 0.8 mm for Door, side & sheles & 0.7mm for back. Four No. of shelves: fo five compartments.Three way bolting device with quality standard make lock with duplicate keys. Double folded type hinges made of MS CRCA sheet thickness 1.6mm to 2.0mm. Three hinges for each door leaf.Finish: Almirah shall be powder coated after seven tanks anti corrosion pretreatment.

Pigeon Hole Locker- Providing and placement of Locker unit Overall size of 6 - Door shall be 915mm(W)x450mm(D)x1830mm(H). LockIng shall have cam lock (Optional) . Material shall be CRCA 0.8 mm thickness. Construction shall be Rigid Welded or Knockdown construction, shelf shall be uniformly distributed load capacity per each shelf level is 50 Kg maximum. Finish shall be epoxy polyester powder coated to the thickness of 50-60 microns. Knob Handle/Label holder shall be Aesthetically appealing Snap fit ABS plastic handle. Ventilation shall be attractive punched pattern for ventilation.(Price Are Excluding Locks)

Steel Book Shelf 4 Drawer- Overall Dimensions: H1675 x D308 xW915mm Material: Prime quality CRCA sheet 0.8mm thick. Compartment door: Each compartment shall provide to-hung glass door, which swings open upwards and slides into the casing when fully open. The Overall size glass (of 4 mm thickness) shall be such, that all the books in compartment shall be visible. For proper alignment of glass door cross plate (patti) arrangement i.e. Kenchi system is to be fitted in each door. Construction: All the components shall be precisely fabricated to high-level workmanship with clean neat and strong joints. Lock & Handles: Two nos. good quality PVC handles are to be provided on each door as shown in photograph with precision lock. Key shall be common for all compartment lock. Finish: The bookcase shall be powder coated after seven tanks pretreatment. The overall appearance of the product shall be as per photograph.

Slotted Angle Rack- Size-1980x915x450 Powder Coated With Five Compartment.Angle Made of 40X40X2mm Thick Slotted MS Angle.and Shelves made of 0.7mm Thick CRCA sheet.Complete body will be pretreated powder coated.

Wooden Stage- Size:-3000W X 1500D X 300H IN mm stage made of 25 mm thick ply top and support

Wooden Stage- Size:-3000W X 1800D X 300H IN mm stage made of 25 mm thick ply top and support

Notice Board Size- 1800X1200 Back Material-Soft Board with balancer laminate,Fabric-Blazer,Outer Profile-Aluminium Extrusion with corner pvc bracket with piuup & Whait/ Glass

WHITE BOARD SIZE- 1800X1200 Back Material-Plain Particle board with balancer laminate,Front-White Marker,Outer Profile-Aluminium Extrusion with corner pvc bracket.

WHITE BOARD SIZE- 900X600 Back Material-Plain Particle board with balancer laminate,Front-White Marker,Outer Profile-Aluminium Extrusion with corner pvc bracket.

ZEBRA BLINDS Polyresin Curtain- P &F VISTA/AD/MAC Or Equivalent S CONTOUR Shade blinds are a truly unique design that features fabric slats suspended between two share fabric facings for complete light control and privacy with all component roller tube control mechanism bottom rail bracket operating chain and cap etc. complete

Water cooler- Approved vide By Dy. CGM order No. 851 /21-08-2020 Ag. No. 14/2019-20 I/ 3 Providing and fixing water cooler Voltas 40/80 FSS water cooler Or Equivalent

Water purifier- Approved vide By Dy. CGM order No. 851 /21-08-2020 Ag. No. 14/2019-20 I/ 10 Providing and fixing forbes water purifier or aqua guard, genius Rot UV + UF Or Equivalent Note:- The Bidder Shall quote his own rates for item rates.

Bidder Name

Amount

BONTON TECHNOMAKE PRIVATE LIMITED(GSTN-23AABCB4237A1ZH)

IMPRESSION FURNITURE INDUSTRIES PRIVATE LIMITED(GSTN-NA)

BONTON TECHNOMAKE PRIVATE LIMITED

BONTON TECHNOMAKE PRIVATE LIMITED