SPL REPAIR FOR REPLACEMENT OF STREET LIGHTS WITH POLES, LT PANELS AND CONNECTED ITEMS AT SOFIPUR AMN DUMP AND P/O 02 NOS HIGH MAST LIGHT CONTROL SYESTEM AT DCN SUB GP DABATHWA UNDER GE(U) MEERUT CANTT

Amount

Supply and fixing Energy saving & Enviroment friendly LED street light fittings made out of pressure die cast anodized alluminium housing having capacity 70 watt. To be achieve B1 class road illumination as per IS: 1944 and as per national Lumens/Watt , CRI > 70 , CCT 5000K to 6500K with LED Lifespan at 70% of light output > 50000 hours. The driver should be 140 V to 270 V universal driver with built in surge protection > 5 kV , 50 Hz +/- 3% , p.f. > = 0.95 , THD < 10% with system efficiency must be > 85 Lumens/Watt and Power efficiency >= 90% and overall IP protection IP 66 or better. The LEDs shall comply LM-80 / IS 16105 Test report , Driver & Luminaire shall comply LM-79/IS:16106 including dismantling of existing street light fittings of any size / type all as specified and directed.

Supplying, transporting, erecting and fixing Steel tubular swaged poles type 410 SP-31 ( 9.0 metres long) complete with cast iron / Mild steel base plate, CI finial, taper plug, bolts, nuts and screws as specified, including necessary excavation and earth work in soft/ loose soil , PCC 1:3:6 type C2 in foundation and around poles and PCC 1:2:4 type B1 as in plinth block duly finished even and smooth without using extra cement (coping will be 30 cm high from ground level), disposal of surplus soil to a distance not exceeding 50 m and depositing where directed, painting exposed surafces steel tubular poles with providing 4 nos bands/ straps with two coats of retro reflective paint ( Black, yellow, white and red 20 cm wide each) from top of plinth block and numbering of poles , painting embedded portion of poles with one coat of bituminous paint including dismantling and removing from site old existing poles alongwith old brackets any size/type complete all as specified and directed.

S&F single arm brackets made out of 32/40mm dia bore or suitable dia bore GI pipe light grade 1.5m long with necessary MS flat iron 40 x 6 mm clamp (02Nos) , nuts, bolts, washers and consisting of adapter to suit the opening of street lighjt including two coats of aluminium paint over a coat of red oxide primer all as specified.

S&F FRP pole mounting type junction box factory made of size 300x200x105mm with front openable hinged door , locking arrangements, with 4 Nos aluminium bus bars 40 Amps rating mounted on porcelain insulator, cable glands and lugs consisting DIN type rails for fixing MCB SP 6/10 Amps, 10 kA, suitable for domestic loading -01 no. including mild steel flat iron clamp made out of 40x4mm FI, nuts, bolts and washers duly painted with two coats of synthetic enamel paint over a coat of red oxide primer complete including taking out and removing old junction box all as specified.(MCB shall not be measured and paid separately and shall deemed included in the unit rate) Make- Sintex/Hensal/Supreme Industries/ National

S&F PVC insulated wire copper conductor 3 core 2.5 Sqmm for connection junction box to street light including PVC conduit not less than 20 mm dia complete and as directed by Engr- in- charge.

Supply, fixing, installation and testing LT pannel out door (Kiosk type) type, wheather & vermin proof MS sheet housing 3.15mm thick, double door front & rear openable type mounted on 50 X 50 X 6mm angle iron frame, floor mounted type with coloured horizontal Tinned aluminium bus bar 4 pole mounted on insulators of rating 400 Amps, one MCCB, 4 pole 100 Amps, 36 KA 415 volts at incoming supply. The panel size not less than 600x450x300mm with cable gland, duly powder coated, locking arrengement complete and including grouting in PCC block of suitable size including dismantling and taking down of old panels of any size / type all as directed by Engr-in-Charge.

Supply, install, testing and commissioning and testing factory made and tested (including CPRI type test certified) LT feeder pillar box (KIOSK) out door type, platform mounted, suitable for 415 Volts 3 phase 4 wire, 50 Hz AC supply system, including taking out old existing pillar box all as specified and directed, having bus bar chamber with insulated aluminium bus bars 600 amps rating installed on porcelain insulators. The panel shall be dust and vermin proof, made of 3.15mm CRCA MS sheet 50 x 50 x 5mm thick MS angle iron frame work, duly powder coated finish. Front & rear opening type with aprons for cable entry with double door shutter and locking arrangement including provision of 65mm Godrej (freedom) lock with 2 keys. The scope of work includes provision of the following :-

Incoming

(a) MCCB 250 amps, 4 pole, 36 KA, with adjustable thermal magnetic release, 50 Hz, 415 volts grade - 01 No.

(b) Bus bar (aluminium strip) 600Amp, 4 pole, not less than 30cm long mounted on insulators for incomming supply 01 No.

(d) Neon LED indicating lamps (R, Y & B) -01 Set.

Out going

(a) MCCB 160 amps, 4 pole, 25 KA, with adjustable thermal magnetic release, 50 Hz, 415 volts grade - 4 No.

Note : (i)Panel shall have platform with PCC (1:4:8) type D-2 using 40mm graded stone crushed stone aggregate 15cm thick in foundation, bricks, masonry in CM (1:6) and 15mm thick rendering in CM (1:6) on exposed surfaces and 100mm thick PCC padding (1:3:6) type C-1 on top and grouting bolts etc for panel. The platform shall be 45cm height from the nearest road level all as directed by Engineer-in-Charge.

(ii) All incoming MCCB shall be connected through MCCB spreaders with incoming busbar and incoming cable shall be connected with incoming bus bar.

(iii) Cost of plate form, MCCB spreders, cable glands , locking arrangement with lock and key of approved make and minor addition /altration if required at site shall be included in the item rate.

Supply, install, testing and commissioning and testing factory made and tested (including CPRI type test certified) LT feeder pillar box (KIOSK) out door type, platform mounted, suitable for 415 Volts 3 phase 4 wire, 50 Hz AC supply system, including taking out old existing pillar box all as specified and directed, having bus bar chamber with insulated aluminium bus bars 400 amps rating installed on porcelain insulators. The panel shall be dust and vermin proof, made of 3.15mm CRCA MS sheet 50 x 50 x 5mm thick MS angle iron frame work, duly powder coated finish. Front & rear opening type with aprons for cable entry with double door shutter and locking arrangement including provision of 65mm Godrej (freedom) lock with 2 keys. The scope of work includes provision of the following :-

Incoming

(a) MCCB 160 amps, 4 pole, 36 KA, with adjustable thermal magnetic release, 50 Hz, 415 volts grade - 01 No.

(b) Bus bar (aluminium strip) 400Amp, 4 pole, not less than 30cm long mounted on insulators for incomming supply 01 No.

(d) Neon LED indicating lamps (R, Y & B) -01 Set.

Out going

(a) MCCB 63 amps, 4 pole, 25 KA, with adjustable thermal magnetic release, 50 Hz, 415 volts grade - 02 No.

(a) MCB 63 amps, 4 pole, 10 KA, with adjustable thermal magnetic release, 50 Hz, 415 volts grade -4 No.

Note : (i)Panel shall have platform with PCC (1:4:8) type D-2 using 40mm graded stone crushed stone aggregate 15cm thick in foundation, bricks, masonry in CM (1:6) and 15mm thick rendering in CM (1:6) on exposed surfaces and 100mm thick PCC padding (1:3:6) type C-1 on top and grouting bolts etc for panel. The platform shall be 45cm height from the nearest road level all as directed by Engineer-in-Charge.

(ii) Cost of plate form, MCCB spreders, cable glands , locking arrangement with lock and key of approved make and minor addition /altration if required at site shall be included in the item rate.

M & L Earthing complete with galvanised MS earth plate of size 600 x 600 x 6mm thick burried directly in ground not less than 2.25 Mtr below ground level, earth plate paced on all side with charcoal mixed with salt to a thickness of 150mm in alternate layers, connected by GI earth strip of size 32 x 6mm thick, soldered and revetted to earth plate. GI earth strip will be protected by using 40mm bore GI pipe (medium grade). The earthing includes PCC pit chamber, RCC pit cover and frame, watering pipe 20mm bore, funnel with wire mess with necessary earth work including disposal of surplus soil to a distance not less than 50 Mtr etc complete including taking out and removing old earthing from site all as specified and shown in electrical plate No 3 of SSR Part-I.

M&L XLPE insulated heavy duty electric cable 95 Sqmm 3 1/2 core with aluminium conductor 1100 volts cross section area (ISI marked) including jointing, testing and commissioning laid in trenches, ducts, pipe or fixed on pole etc and taking out/ dismantling of U/G old cables all as specified and directed.

Description all as per serial item No 11 above but XLPE insulated heavy duty electric cable 50 Sqmm 3 1/2 core

Description all as per serial item No 11 above but XLPE insulated heavy duty electric cable 25 Sqmm 4 core

Description all as per serial item No 11 above but XLPE insulated heavy duty electric cable 16 Sqmm 4 core

Supply & fixing or laying 50 mm bore galvanised steel tubing light grade (ISI marked) for protection of under ground cable on poles/ walls under road crossing etc of following sizes including dismantling and taking down existing pipe.all as specified and directed.

Description all as per serial item No 14 above but 40 mm bore pipe

M & L for boaring in any type of soil under road 1.5 Mtr below the top surface of road by conventional method complete for passing through 40mm to 100mm dia GI pipe and filling earth after laying of pipe including disposal of surplus soil complete all as specified and directed.

Excavation in trenches in soft/loose soil n. exc. 1.5 meter wide and n. exc. 1.5 mtr depth and getting out, including trimming the sides and forming bottom surface to required levels for laying cables, foundation of poles, stay etc complete all as specified.

Returning, filling trenches including spreading, levelling, watering and well ramming in layers n. exc. 25 cm thick complete all as specified and directed.

Removing of excavated material (soil) to a distance n. exc. 50 Mtr and dispositing where directed at a level n. exc. 1.50 Mtr above the starting point complete as directed.

M & L Sand cushioning to UG cables (8cm deep before laying of cable and 15 cm deep over the cable). Note :- Punned thickness only will be considered for payment.

M & L Bricks for protection cover to under ground cable (with standard size fly ash bricks) with width equal to length of brick laid dry and flat abutting each other with gaps between adjacent brick not exceeding 10mm as directed.

M&L for preparation of old painted surfaces of erected steel tubular swaged poles / Rails/Girder poles of LT over head line ( Except embedded portion) , 9/11 M long including all MS work mounted on pole , earth protection & water pipe ( if exists) and providing one coat of aluminium paint and providing 04 Nos bands/ straps with two coats of Retro Reflective paint ( black, yellow, white and red 20 cm wide each) from top of plinth block and numbering of poles with white Retro Reflective paint on yellow Retro Reflective piant ground (50mm wide and 100mm high letters) including encircling the letters or figures complete all as specified

Supply, laying and testing cable XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured, electric power cables (heavy duty) 1100 volts grade with stranded aluminium conductor of size 25 sqmm 4 core complete all as specified and directed.

Supply & installation of 16M high mast shaft in two sections having 3mm thickness suitable for 47 m/sec wind speed as per IS-875.Part-III, with head frame, winch mounting bracket, luminaries carriage suitable to install upto 8 nos luminaries in symmetrical arrangement. Supply of raising lowering system comprising double drum winch, 5mm SS wire rope, trailing cable of 5Cx2.5Sqmm, connector, integral power tool motor of 0.75 HP, manual handle, junction box, lightening finial. Supply of foundation bolts manufactured from special steel along with nuts, washers, anchor plate and common template. NOTE:- Manufacturer must be ISO 9001, ISO 14001 and ISO 45001 certified. Manufacturer should have their own plant in India (make in India) and submit Licence and Certificates of factory Registration. Raw Material (Steel) Grade must be as per BS-EN10025/IS 2062 and having silicon content not more than 0.6%. L1 Bidder Need to submit Raw Material test certificate from Steel Manufacturers only through pole manufacturer. Manufacturer must have Hot Dip Galvanisation facility in their plant only with minimum 13 mtr long Galvanizing tank. Structural calculations of Poles should be submitted by bidder as per IS-875 Part-III. Manufacturer should have CNC Controlled plasma sheet cutting and bending machine and Fully Automated Submerged arc welding machine for perfect single longitudinal welding of shaft

Supply and fixing LED flood light fitting 250 W, 230 volt , AC outdoor type with thermal management in multiple optics and equipped with IP 66 protection, with impact and corrosion resistance complete all as specified and directed. Model GLEAM F 275L WH SY WH SY PC SD V2

M& L for earthling complete with galvanized steel earth plate, electrode 600 x 600x6 mm thick , buried directly under ground (earth pit not less than 2.25 m below ground level ) with top edge of the plate not less than 1.5 below ground level connected to galvanized strip 32x6mm by means of nuts, bolts, check nuts & washers, of galvanized iron or steel all as Shown in electrical plate No 3 on Sl. Page 19-497 of MES schedule 2009 part I and connected to existing equipment/system, including all necessary excavation & earth work in hard/dense soil, common salt and charcoal dust mixed & packed 150 mm thick homogeneous layer all around the GI earth plate, GI protection pipe 40mm light grade upto 7.5 meter from electrode complete all as specified & shown on drawings with watering pipe medium grade 20mm dia ,GI sheet funnel with wire mesh ,RCC precast cover 1:2:4 type B1 duly reinforced with TMT bar 8mm dia at the rate of 150mm centre to centre both ways with suitable lifting handle ,pit/chamber in PCC 1:3:6 type C1 ,Angle iron 40x40x5mm frame for pit cover including testing on completion complete all as specified and directed.

Supplying and fixing in repair automatic operation street light timing switch having lighting control (ON-OFF) through Astronomical Calculation of Sun rise/ sun set by setting date, time and degree of longitude and latitude without separate light sensors and prewired with suitable size of copper conductor single core PVC insulated and sheathed caable and all mechanism fitted into panel, outdoor type , pole mounted with FI 25x4mm clamps , nuts, bolts and washers dully painted, connecting and testing factory made , epoxy powder coated, Single Phase street light panel, digital 24 hrs, suitable for 6KW (max) complete with 32 Amps TP Contactor, and 40 Amps SPN MCBs and fixed on pole/ wall/ feeder pillar complete all as specified and directed.

KUKREJA BROTHERS

sanjeev enterprises

SA construction co.

mohanlal gupta

Narender Construction

Ravi Electrical

m/s sweta trading co.

M K ENGG CO