work for installation of new Distribution Transformers against Additional Business Plan 2024-25 for quality power supply in Aligarh City on Semi Turn-key Basis under the area EUDC, Aligarh

Amount

Safe carriage of following materials from Store centre or any other place to the respective site of work through the Kachha/Pacca road including loading, unloading at the respective ends and erection of same including the work of dragging as per site requirement, jumphering of Transformer with 11 KV line through LT ABC cable, Weasal conductor etc. Cost of labour, T&P carrier etc. required for proper completion of work as per RESPO Norms is included in the work.

ST Pole 09 Mtr Long

ST Pole 11 Mtr Long

Earthing complete

Stay complete(GI Stay Rod 16x1800mm, 5 Kgs. Stay wire 7/8, Stay clamps, Insulator, Bolts, Nuts & Washers)

11 KV XLPE Cable 3x70sq.mm.

ACSR Weasel Conductor

AB Cable 3x95+1x70+x16 sq.mm.

AB Cable 3x120+1x95+x16 sq.mm.

L.T. Al. Cable 1x240 Sq.mm.

L.T. Al. Cable 1x400 Sq.mm.

L.T. XLPE 3.5x150 Sq.mm.

Distribution Transformer 100 KVA

Distribution Transformer 400 KVA

Distribution Box with Clamp

11 KV D.O. Fuse Set

11 KV TPMO

11 KV Pin Insulator with Pin

11 KV Polymer Disc Insulator with fitting

Supply, fixing and erection of following materials as per site requirement as per RESPO Norms:-

11 KV cable Jointing Kit 3x70sq.mm. (outdoor)

Stone Pad

ABC Connector (PIERCING)

Suspension Clamp with I Hook

Deadend Clamp with I Hook

AL LUG 120 SQMM / 240 Sq.mm.

AL LUG 400 SQMM

Top Channel size 125x65x2240 mm.

Dropper Channel size 100x50x2028 mm.

Tee off Chennal size 125x65x1300 mm.

Base Angle size 75x75x6x2028 mm.

Pole Clamp with nut & bolt

Danger Board with Clamp

Nut Bolt & Washer

Hanely type L.T Tailless Unit 300 Amp with Cubical & Fitting

Hanely type L.T Tailless Unit 500 Amp with Cubical & Fitting

L.T Incoming Panel with metering equipment & fixing arrangement

Neutral & body earthing of Power Transformer, Distribution Transformer & Incoming/Outgoing VCBs installed at various 33/11 kV Sub-stations by digging of pit upto water level depth (approx. 125 feet) and then inserting 1-¼” dia GI pipe of ‘A’ grade, conforming to the requirement of IS specification and then connecting the top of the inserted pipe and transformer body through GI strip of size 40x6 mm with the help of nut and bolt or through gas welding, as per direction of supervising engineer. It includes the cost of all material labour, T&P, carrier etc. required for proper completion of work. The aforesaid work shall be carried out as per RESSPO norms.

Providing and fixing of welded wire mesh fencing around transformer plinth with M.S. Angle of size 35X35X6 mm. length and 1.20 Meters height, such panels shall be supported on M.S. Angle from of size 40X40X6 mm. having 04 Nos. corner supports of height 1.65 Meters including extended legs for grouting which will be used as a door for entry of the personnel or removal/shifting of transformer with welded hinges, sliding belt etc. for locking the arrangement as per drawing and specifications the fencing will be painted one coat of red oxide primer and then two coats of bus green synthetic enamel paint. The rates should be inclusive of all materials required for proper completion of above work (length of each fencing approx. 11 Meters)

KHAN ENTERPRISES