Renovation/construction work at HIRMI Kurukshetra.

Amount

Dismantling Brick work,Tile Massonary or Tle Lining and Tile Terracing In cement(compelte as per HSR item No 8.5 (b)

Removing of old chairs (compelte as per NS item )

Removing door and windows (wood and steel) with chowkats by making recess in walls when the wall is not dismantled :- (compelte as per HSR item No-8.18) Doors compelte as per HSR item No-8.18 (a)

Windows compelte as per HSR item No-8.18 (b)

Dismantling cement concrete / terrazo floors 25 mm to 50 mm thick including concrete base.(compelte as per HSR item No-8.25)

Dismantling of plank ceiling and supporting timbers(compelte as per HSR item No-8.30)

Removing of wooden cladding/paneling (compelte as per NS item)

Earth work in excavation in foundations , trenches etc. in all kind of soils,not exceeding 2 metres depth including dressing of bottom and sides of trenches stacking the excavated soil,clear from the edge of excavation and susequent filling around massonary in 15 cm layers with compaction,including disposal of all surplus soil as directed within a lead of 30 metres.(compelte as per HSR item No-6.6)

Earth work filling in tiba sand from as av. Lead of 8 k.m. filling in 15cm layer (compelte as per HSR item No 4.1a+5.2b)

Sand filling under floor and in wells of bridge foundation including handling within 100 meters.(compelte as per HSR item No-14.83)

Providing sand for filling at site compelte as per NS item)

Centering and shuttering for flat surfaces such as suspended floors, roofs,landings,chajjas,shelves etc.inclination not exceeding 25 degree with horizenatal.(compelte as per HSR item No-9.1)

Centering and shuttering for side and soffit of beams hunching,girers,bressumers and lintals.(compelte as per HSR item No-9.7)

Centering and shuttering for columns ( square or rectangular or polygonal in plan)(compelte as per HSR item No-9.9)

Shuttering for face of concrete foundation and foundation beams ( vertical of battering)(compelte as per HSR item No-9.13)

Cement Concrete 1:4:8 with store agreegate 20mm nominal size in foundation and plinth.(compelte as per HSR item No-10.38)

Cement concrete 1:8:16 with stone agreegate 20 mm nomional size in first storey upto 4 metres above plinth level.(compelte as per HSR item No-10.47)

Design mix cement concrete of grade M-30 with minimum cement content 420 kg/cum in foundatin and plinth.(compelte as per HSR item No-10.67)

Design mix cement concrete of grade M-25 with minimum cement concrete 405 kgs / cum in first storey upto 4 metres above plinth level(compelte as per HSR item No-10.73)

Design mix cement concrete of grade M-30 with minimum cement concrete 420 kgs / cum in first storey upto 4 metres above plinth level (compelte as per HSR item No-10.74)

Damp proof course 40 mm thick of cement concrete 1:2:4 using stone agreegate with 2 coats of bitumen 20/30 penetration at 1.65 kgs per sqm laid hot and sanded.(compelte as per HSR item No-10.114)

First class brick work laid in cement sand mortar 1:6 in foundation and plinth.(compelte as per HSR item No-11.2)

First class brick work laid in cement sand mortar 1:6 in super structure above plinth .(compelte as per HSR item No-11.7)

11.43 cm thick brick wall laid in cement sand mortar 1:4 witout reinforcement in foundation and plinth.(compelte as per HSR item No-11.47)

11.43 cm thick brick wall in cement sand mortar 1:4 in super structure.(compelte as per HSR item No11.48 (a)

Terracing consisting of tiles 22.86 cmx11.43 cm x 3.81 cm laid over 87.50 mm mud filling on a layer of 25 mm mud plaster and another layer of mud mortor for laying the tiles, including two coats of bitumen laid hot at 1.65 kgs per sqm on top of RCC slab including grouting with cement mortor 1:3 and top surface to be left clean.(compelte as per HSR item No-13.13)

Providing and embedding 100 mm dia HCI rain water witout ears ISI mark pipe in cement mortor during massonary work.(compelte as per HSR item No-13.43)

Providing and fixing cast iron shoe for 100 mm dia rain water pipe on wooden plugs fixed on wall face including filling the joints with spun yarn and cement mortor 1:2.(compelte as per HSR item No-13.48)

Top khurra 0.6x0.6 m for rain water pipe in 25 mm thick cement concrete 1:2:4 over 50 mm thick cement concrete 1:8:16.(compelte as per HSR item No-13.50)

Bottom khura on ground 1.2 m x 0.6m consisting of brick on edge laid in cement mortor 1:3 over 75 mm cement concrete 1:8:16 including 12 mm thick cement plaster 1:3.(compelte as per HSR item No-13.57)

Cement concrete 1:2:4 gola 10 cm x 10 cm quadrant along junction of roof with parapet wall finished smooth where specially specified.(compelte as per HSR item No-13.64)

Providing and fixing false ceiling with 12mm thick gypsum board fixed on M.S Steel runners frame i/c cost of screw angles, cleats, rawel plugs, with taping, filling with gypsum compound and applying priming coat etc. complete in all respect.(compelte as per HSR item No-13.91)

40 mm thick grey polished flooring cement concrete 1:2:4 topping finished with 3 mm thick neat coat of cement rubbed and polished.(compelte as per HSR item No-14.17)

Kotah stone flooring 34 mm to 40 mm thick in any pattern as specified over 12 mm thick base of cement coarse sand mortor 1:3 laid and jointed with neat cement slurry mixed with pigment to match the shade of stone including rubbing and polishing.(compelte as per HSR item No-14.62)

Stage Flooring Specification: P/F vibration isolated wooden stage flooring, consisting of a wooden base grid made of 50mm x 75mm wooden runners (hollock/ marandi) at a spacing of 600mm c/c in with directions.The wooden grid work will be laid on 1/2" thick neoprene padding to provide vibration isolation. The entire grid work to be filled with dry fine river sand.Framework to be covered with 12.5mm thick waterproof ply.Top later consisting of 12.5mm thick engineered hardwood finish, as per Architects.(Make: Earcons , Anutone, Navyug Acoustic)(compelte as per NS item)

Providing and fixing of Luxury Vinyl Floor 2.5MM as per ASTM F 386 with .50MM wear layer vinyl floorings of VIBRANT FLOORS series with dimensions of 184MM and length of 950MM or Tiles size 570MMx570MM as per company standard should be approved by architech. 5 mm thickness to laid on hard, levelled, smooth and moisture free sub floor. Vibrant LVT shall be installed with company recommonded bond or adhesive. Vibrant Luxury Vinyl Floor should have traffic classification 32 . Product shall be ISO approved. LVT should be floor score and T abrasion class approved. Flooring should have caster chair EN-985 tested with color fastness of more than 6. It shoukld be ASTME662 qualified on Smoke density test. Product should be fire rating of the product should be Bfl-S1. and Wear Group of T Class. As per approved shade and colour as per the satisfaction of the Architect. (compelte as per NS item)

Commercial Carpet : -Providing & Fixing of the loop & cut pile designed carpet with 8mm profeel underlay. Complete with adhesive after rectification of the floor as per the specification and direction of the incharge.(compelte as per NS item)

Providing and fixing vitrified tiles of size 600 x 600 mm of approved make in flooring laid in any pattern as specified over base of 20 mm thick cement coarse sand mortor 1:3 and jointed with white cement slurry mixed with pigment to match the shade to tiles.(compelte as per HSR item No-14.89)

Providing and fixing vitrified tiles of size 600 x 600 mm of approved make in skirting / dado laid in any pattern as specified over base of 12 mm thick cement coarse sand mortor 1:3 and jointed with white cement slurry mixed with pigment to match the shade to tiles.(compelte as per HSR item No-14.90)

Providing and fixing ceramic tiles/anti skid tiles of size 400 x 400 mm or above size of approved make in flooring laid in any pattern as specified over base of 20 mm thick cement coarse sand mortor 1:3 and jointed with white cement slurry mised with pigment to match the shade of tiles.(compelte as per HSR item No-14.91)

Providing & Fixing of unistone or equivalent glass Reinforced Concrete (G.R.C) Wall Cladding Tiles in approved Design, size 250mm x 100mm, texture, thickness, pattern and color. The thickness of the tiles should range between 10 to 20 mm (depending on the texture of the tile), allowing variance of +2mm in accordance with IS: 1237 - 1980. The composition of tiles should be '43' Grade portland cement, reinforced with Alkali Resistant Glass Fiber and homogeny pigmentation should be done with exterior grade synthetic inorganic iron oxide pigments manufactured by ' BAYFERROX / Lanxess (Germany)' or equivalent. the pigmentation should be homogeneous and in accordance with British Standards BS EN 12878:1999. The other additives should be fine washed graded quartz, super plasticizers and integrated water proofing agents and others. The tiles should be produced with high vibration technology and concrete mix design compressive strength equivalent to M - 40 Grade@28 days. The top surface of the tiles should be sealed with acrylic lacquerr resulting in surface water absorption of tiles, less than 1% and water absorption by 24 hrs immersion method, less than 8%. The tiles should be applied on a rough plaster of 1:3 cement mortar 1:3 (1 cement : 3 coarse sand) and the fixing of tiles should be done by unistone tile adhesive or equivalent as per manufactures laying instruction.(compelte as per NS item)

Providing and fixing 1st quality ceremic glazed wall tiles confirming to IS 15622 ( thickness to be specified by the manu-facturer) of approved make in all colours,shades except burgendy,bottle green,black of any size as approved by Engineer in charge in skirting /,riser of steps and dados over 12 mm thick bed of cement mortor 1:3 coarse and jointed with grey cement slurry ,including pointing in white cement mixed with pigment of matching the tiles.(HSR No-14.92) (b)Size of ceremic Glazed tiles 300 x 450 mm (compelte as per HSR item No-14.92 (b)

Providing and laying gang saw cut 18 mm thick, mirror polished pre moulded and pre polished machine cut granite stone of required size and shape of approved shade, colour and texture in footpath, flooring cut granite stone of required size and shape of approved shade, colour and texture in footpath, flooring in road side plazas and similar locations, laid over 20mm thick base of cement mortar 1:4 (1cement : 4 coarse sand) including grouting the joints with white cement mixed with matching pigment, epoxy touch ups etc. complete as per direction of Engineer-in-Charge. 16.86.1 With granite stone of area less than 0.50 sqm(compelte as per DSR item No-16.86)

Providing and fixing of S.S.handle 8" long fixed with recources etc.complete in all respect.(Ns item)

10 MM cement plaster 1:3 under side of ceiling.(compelte as per HSR item No-15.51)

12 mm thick plaster 1:5(compelte as per HSR item No-15.6)

15 mm thick cement plaster 1:5 on the rough side of single or half brick wall.(compelte as per HSR item No-15.11)

Cod twisted deformed (ribbed/tor steel) bars for RCC works,where no including in the complete rate of RCC including bending,binding and placing in position complete.(compelte as per HSR item No-18.22)

Teak wood chowkets of doors and windows including iron hold fasts,corner straps,screws,bolts for hold fasts etc.complete in all respect.(compelte as per HSR item No-17.13)

Providing and fixing 40 mm thick Factory manufacturer solid flush door shutters with block board core as per IS No. 1659-1969 bonded with water proof type phenol formaldehyde synthetic resin,hot pressed,conforming to IS 2202 part I and II fixed in position including iron hinges screws chockes/cleats and stops etc. ( excluding the cost of any fitting other than specified above but including labour for fixing the same in position) with decorative veneering with vertical grains or cross bands and face veneer on both side teak facing and edges lipped with commercial hard wood with laminated core.(compelte as per HSR item No-17.93 (c)

Providing and fixing factory made uPVC white colour casement/casement cum fixed glazed windows comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, stainless steel (SS 304 grade) friction hinges, zinc alloy (white powder coated) casement handles, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes and silicon sealant shall be paid separately) Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerancein dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. 9.147A.1 Casement window single panel with S.S. friction hinges (300 x 19 x 1.9 mm), made of (small series) frame 47 x 50 mm & sash 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glass pane glazing bead of appropriate dimension. (Area of window upto 0.75 sqm.)(compelte as per DSR item No-9.147A)

Providing and fixing Aluminium work for doors windows,ventilators and partitions with extruded builtup standard tubular sections / appropriate Z sections and other sections of approved make confirming to IS 733 and IS 1285 fixed with rawlplugs and screws with fixing clips or with expansion hold fasterners including necessary filling up the gaps at junctions at top ,bottom and sides with required neoprene felt etc. aluminium sections shallbe smooth,rust free straight mitered and jointed mechanically whereever required including cleat angle,Aluminium snap beading for glazing / panelling CP brass / stainless steel screws etc.complete.Shutters of doors,windows and ventilators including providing and fixing hinges/pivots and making provision for fixing of fitting whereever required including the cost of PVC/neoprene gasket required including aluminium fitting.(compelte as per HSR item No-17.96)

Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board confirming to IS : 12823 grade I type II in panelling fixed in aluminium doors,windows shutters and partition frame with c.p. brass / stainless steel screws etc. complete.(compelte as per HSR item No-17.97) Pre laminated particle board with decorative lamination on both side.(compelte as per HSR item No-17.97 (b)

Providing and fixing 5 mm thick float glass glazing in aluminium doors,windows,ventilator shutters and partition etc. with pvc / neuoprene gasket etc. complete (Cost of aluminium snap beading shall be paid in basic items.)(compelte as per HSR item No-17.98 (b)

Providing and fixing aluminium round shape handle of outer dia 100 mm with screws etc. complete (compelte as per HSR item No-17.102) (ii)Powder coated minimum thickness 50micron aluminium.

Providing & Fixing of perforated600 X600 acoustic tile on Grooved Ceiling T Grid systen with acoustical backing that improves sound quality and reduces reverberation time on 15 mm black grooved selhoute grid. The tiles should have 100% water resistance & fire resistance as per BS 476 , Light Reflectance >75% in module size of 595 X 595 X 8 mm . The tile should be Termite proof. Minimum 15 mm wide grid T sections i.e. the Main Runner 3000mm in web height of 32mm, 1200 mm & 600 mm Cross Tees in web height of 26mm. INSTALLATION:-To comprise main runner spaced at 1200mm centres securely fixed to the structural soffit using suspension system at 1200mm maximum centre. The First/Last suspension system at the end of each main runner should not be greater than 450mm from the adjacent wall. Flush fitting 1200mm long cross tees to be interlocked between main runners at 600mm centre to form 1200 x 600 mm module. Cut cross tees longer than 600mm require independent support. 600 x 600mm module to be formed by fitting 600mm long flush fitting cross tees centrally between the 1200 mm cross tees. Perimeter trim to be wall angles of size 3000x19x19mm, secured to walls at 450 mm maximum centres. Work complete in all respect as per the drawing to the satisfaction of Engineer in-charge or Project Officer.(compelte as per NS item)

Providing & Fixing of Wooden Acoustical Suspended Ceiling System – square/micro edge tile Lay in on 15 mm exposed Grid. The high Grade MDF panels having melamine laminated faced with hole or Slot system backed with a nonwoven fabric covering of 0.2mm for providing sound absorption via acoustic impedance method. The tiles should have Humidity Resistance (RH) of 99%, NRC 0.75, Light Reflectance >84% with Fire Resistance as per BS476 (Part 6 & 7) in module size of 595 X 595 X 12 mm@ 400kg/m3 density. The Grid should be 15 mm wide T sections i.e. the Main Runner 3000mm in web height of 32 mm, 1200 mm & 600 mm Cross Tees in web height of 26mm to comprise main runner spaced at 1200mm centers securely fixed to the structural soffit using suspension system at 1200mm maximum centre. The First/Last suspension system at the end of each main runner should not be greater than 450mm from the adjacent wall. Flush fitting 1200mm long cross tees to be interlocked between main runners at 600mm centre to form 1200 x 600 mm module. Cut cross tees longer than 600mm require independent support. 600 x 600mm module to be formed by fitting 600mm long flush fitting cross tees centrally between the 1200 mm cross tees. Perimeter trim to be wall angles of size 3000x19x19mm, secured to walls at 450 mm maximum centers and as per the drawing and the work complete in all respects to the satisfaction of Engineer in-charge.(compelte as per NS item)

Providing and fixing false ceiling at all heights with integral densified calcium silicate reinforced with fibre and natural filler false ceiling tiles of Size 595x595mm of approved texture, design and patterns having NRC (Noise Reduction coefficient) of 0.50 (minimum) as per IS 8225:1987, Light reflectance of 85% (minimum). Non combustible as per BS:476 (part-4), fire performance as per BS:476 (part 6 &7), humidity resistance of 100%, thermal conductivity < 0.043 W/m K as per ASTM 518:1991,in true horizontal level suspended on interlocking metal T-Grid of hot dipped galvanised iron section of 0.33mm thick (galvanized @ 120 grams per sqm including both sides) comprising of main-T runners of size 24x38 mm of length 3000 mm, cross - T of size 24x32 mm of length 1200 mm and secondary intermediate cross-T of size 24x32 mm of length 600mm to form grid module of size 600 x 600 mm, suspended from ceiling using galvanised mild steel items (galvanizing @ 80 grams per sqm) i.e. 50 mm long, 8 mm outer diameter M-6 dash fasteners, 6 mm dia fully threaded hanger rod upto 1000 mm length and L-shape level adjuster of size 85x25x25x2 mm. Galvanised iron perimeter wall angle of size 24x24x0.40 mm of length 3000 mm to be fixed on periphery wall / partition with the help of plastic rawl plugs at 450 mm center to center and 40 mm long dry wall S.S screws. The work shall be carried out as per specifications, drawing and as per directions of the Engineer-in-Charge. 26.22.1 With 15 mm thick tegular edged light weight calcium silicate false ceiling tiles.(compelte as per DSR No-26.26.1)

Providing & Fixing of pvc panel mega star brand hd quality with 5mm thickness size 3.04 meter x.25 meter made of upvc material,laminated with pvc foil as per desire color fixing with pvc wall plug and 1" screw. (compelte as per NS item

Providing & fixing customized grooved wooden panel of Medium Density Fibreboard having system NRC up to 0.75 with lineal perforation on auditorium side wall as per architect drawings & designs. The panels shall be Non FR grade with melamine laminate panels 2440mm x128mm x 16mm with 2mm groove at 14mm pitch, Tongue and Groove edges for seamless mounting having density of 400kg/m3(base panel confirming to IS 12406. The Panel is fixed by using GI Framework spaced at 600mm centres @ 1 mm wooden ply strips framework spaced at 400mm centers with suitable hardware and the system is backline with 50 mm insulation and along with all accessories. Continue installing rows of panels by inserting screw & plugs into the groove of the wooden panel and progressively installing the panel into the next keel till the actual height is achieved. Finish off the edges using wooden moulding of matching colour. The panelling work shall be done in all respects as per detailed drawings. The Work complete in all respect as per the drawing to the satisfaction of Engineer in-charge or Project Officer. INSTALLATION:Screw the aluminium extruded keel for channelled woodworks over if required existing GI stud framework and insert the wooden panels by inserting the clips as per manufacturer’s specifications. Finish off the edges using wooden moulding of matching colour (provided by others) complete in all respect to the entire satisfaction of engineer-in-charge/Architect.(compelte as per NS item)

Providing and Fixing onsite customized Stretch Fabric panel for side walls above 8ft height on G.I studs 2400mm X 50mm web flanges 15 & 50mm fully knurled giving it high strength, hot dipped galvanized steel with 120GSM zinc coating specially designed for Acoustic vibration management and long life with a backing 50mm thick Rock wool @48kg density insulation intact with chicken mess wires NRC up to .90. To be mechanically fastened on the G.I Studs. Then 12mm Vinyl tracks are screw fixed on to the 12 mm Ply and Acoustics panel’s .Then the fabric is stretched over the Vinyl tracks. The installed system should provide NRC OF 1.00.Fabric colour as per Architect choice-Ref attached specifications for more details. The system to be installed on G.I studs 600x600mm centre to centre 2400mm X 50mm web thickness 0.5mm, flanges 15 & 50mm fully knurled giving it high strength, hot dipped galvanized steel with 120GSM zinc coating specially designed for Acoustic vibration management and long life with a backing of 50mm thick, 1000 GSM Rock wool tested as per Fire Retardant ASTMD 635-1991 /Insulation and IS 15061-2002 for excellent results. Work complete in all respect as per the drawing to the satisfaction of Engineer in-charge or Project Officer.(compelte as per NS item)

Providing and applying two coats white cement based putty over plastered surface and grinding the surface smooth with sand paper to get an even and smooth finish including cost and carriage of all material, labolur charges, scaffolding, sundries etc. complete (J.K./Birla Make) (Complete as per HSR item No-16.81)

Finishing walls with textured exterior paint of required shade : 13.45.1 New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @ 2.20kg/10 sqm(Complete as per DSR item No-13.45)

Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade: 13.47.1 New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) WALLS(Complete as per DSR item No-13.47)

Painting two coats with ready mixed emulsion paint in all shades for interior use on bricks,plaster ,cement fibre board etc. ceiling new(Complete as per HSR item No-16.27)

Push Back Cum Tip -up Auditorium Chair: Push back with Auto tip-up chair & synchronus movement of back & base foam together. PU Foam Density - 45 kg/cubic mtr, Upholstered cover in back base , with Cupholder Armrest Height - 1050MM Width -550 MM Depth - 700 MM , Back movement - 120 MM(compelte as per NS item)

Providing and fixing in position best Indian make Lavatory suits (Angle back) in vitrous chinaware and all other necessary fitting as fully described in HSR item no. 30.41 White colour size 530x430 mm with one no. tap (compelte as per.HSR item No-30.43)

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : (a)Kitchen sink with drain board 510x1040 mm bowl depth 225 mm( compelte as per DSR No-17.10.1.2 (a)

Providing & fixing in position best indian make bevelled edge 5.5 mm thick mirror mounted on asbestos sheet ground fixed in position by means of 4 nos. chormimum plated brass screws and washers over rubber washers and rawl plg embedded in the wall or chromium plated brass clamps with C.P brass screws (as eequired by the Engineer-in-charge) complete including cutting and making good the walls etc. (i) 600mm x 450mm (complete as per HSR item No-30.71 (i))

Providing & fixing in position best indian make towel rails fixed in with rawlslugs embeded in walls with C.P brass screws. Complete in all respect including cutting and making good the walls etc. 20mm dia CP brass adjustable 600 mm long (complete as per HSR item No-30.68 (b) ii)

Providing & fixing lead inlet connection with brass union for flushing and warning pipe complete in all respects. 15 mm alkathene pipe ilet connection (complete as per HSR item No-30.93 -C)

Providing & fixing in position automatic brass ball valves in the tanks.(30.110,a)ii 20mm internal diameter(complete as per HSR item No-30.110 (a)ii)

Providing and fixing HDPE WATER STORAGE TANKS of Sintex,Diplast,O.K.Supreme make with cover / lids marked with IS:12701 on roof top of building including the cost of hoisting and placing in position,making connections with inlet and outlet pipes,providing overflow and scour provisions with suitable plug on scour pipe including cost of nipples,washers,flanges for connections in tanks complete in all respects to the satisfaction to the Engineer in-charge .Capacity 1000 ltrs.(complete as per HSR item No-30.119)

Providing and fixing 100 mm dia centrigugaly cast (Spun) iron socket spigot (S&S) pipe as per IS:3989 complete in all respect.(complete as per DSR item No-17.35.1.2)

Providing and fixing 75mm dia centrigugaly cast (Spun) iron socket spigot (S&S) pipe as per IS:3989 complete in all respect.(complete as per DSR item No-17.35.2.2)

Providing and filling the joints with spun yarn, cement slurry and cement mortar 1:2 ( 1 cement : 2 fine sand) in S.C.I./ C.I. Pipes : (i) 17.36.1 75 mm dia pipe(complete as per DSR item No-17.36.1)

(ii) 100 mm dia pipe(complete as per DSR item No-17.36.2)

Providing and fixing G.I. Pipes complete with G.I. fittings and clamps, i/c making good the walls etc. concealed pipe, including painting with anti corrosive bitumastic paint, cutting chases and making good the wall :(complete as per DSR item No-18.11) 15 mm dia nominal bore(complete as per DSR item No-18.11.1)

20 mm dia nominal bore(complete as per DSR item No-18.11.2)

Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms. 15 mm nominal bore(complete as per DSR item No-18.50.1)

Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design: 100x100 mm size P type With common burnt clay F.P.S. (non modular) bricks of class designation 7.5( complete as per DSR item No-19.4.1.4)

Providing sand cast iron drop connection externally for 60 cm drop from branch sewer line to main sewer manhole including inspection and cleaning eye with chain and lid, sand cast iron drop pipe and bend encased all-round with cement concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) with all centering and shuttering required, cutting holes in walls and making good with brick work in cement mortar 1:4 (1 cement : 4 coarse sand) plastered with cement mortar 1:3 (1 cement : 3 coarse sand) on inside of the manhole wall, lead caulked joints between sand cast iron pipes and fittings, stiff cement mortar 1:1 (1 cement : 1 SUB HEAD : 19.0 DRAINAGE 368 Code Description Unit Rate No. fine sand) joints between sand cast iron tee and S.W. pipe, making required channels complete as per standard design and specifications : 100 mm dia sand cast iron drop connection(complete as per DSR item No No-19.22.1.1)

MCB DB DOUBLE DOOR Supply and erection of double door sheet steel enclosures distribution boards suitable for MCBs and ELCBs etc. recessed in wall including bonding to earth with all labour and material requared complete the job in all respect upto the entire satisfaction of the Engineer-in Charge of the work.( HSR No-31.41) 16-way, SP & N (Horizontal) for Auditorium UPS DB( complete as per HSR item No-31.41 (iv)

8-way, TP & N (Horizontal) (8+24), for Auditorium & Mess (Ltg. & Power DB's)(HSR No-31.41 (vi)

ELCB/RCCB Supply and erection of double Double Pole /Four Pole Residual Current Circuit Breaker (RCCB /ELCB) suitable for operation on 240V/415V, 50Hz, AC supplu installed in existing sheet steel enclosure including making necessary connections and bonding to erarth with all labour and material required to complete the job in all respect upto the entire satisfaction of the Engineer-in-Charge. (HSR No-31.42) 40A/240V DP RCCB/ELCB with 100ma sensitivity (for 16way SP & N DB and Ltg. DB of Auditorium)(complete as per HSR item No-31.42)(viii)

63A/240V DP RCCB/ELCB with 100mA/300mA sensitivity (for PDB & Mess DB) (complete as per HSR item No-31.42 (ix)

63A/240V DP RCCB/ELCB with 100mA sensitivity (complete as per HSR item No-31.42 (x)

MCB`s Supply and erection of miniature circuit breaker, 240V/415V in the existing distribution board including making necessary connections :- (a) Miniature Circuit Breakers of 9kA breaking capacity single pole ( complete as per HSR item No- 31.17 ) SP MCB of 9 KA breaking capacity 6 amp. to 32 amp (6A SP MCB - 32nos, 16A/20A SP MCB - 28nos & 25A SP MCB -6nos).(complete as per HSR item No-31.17(a) (ii)

40A TPN MCB of 9 KA breaking capacity(complete as per HSR item No-31.17(a) (iii)

63A TPN MCB of 9 KA breaking capacity(complete as per HSR item No-31.17(a) (iii)

40a DP MCB of 9 KA breaking capacity(complete as per HSR item No-31.17(a) (iii)

INDUSTRIAL SOCKET Supply and erection of sheet steel enclosure 2 pole / 3 pole with earth plug and socket suitable for incorporating single pole / triple pole MCB on wall / on existing pedestal complete with necessary connections etc. (HSR No-31.15) (ii)S.P.N. enclosure for single pole MCB 20A For AC's (complete as per HSR item No-31.15(ii)

BLANK SHEET Supply & erection of blanking sheet in existing Distribution Board(complete as per HSR item No-31.16)

Earthing Providing and fix 25mm X 5mm G.I Strip in 40 mm dia G.I pipe from earth electrode as required .(HSR No-31.22 (XI)

Providing and fixing 25 X 5mm copper strip on surface or in recess for connections etc., as required. With all labour and matrial compelte as per HSR item No-31.22 (XIV)

Providing and fixing 4.0mm dia copper wire on surface or in recess for loop earthing etc., as required..(complete as per HSR item No-31.22 (XVII)

Call bell 220 / 230 volts A.C. bakelite with double coil.(complete as per HSR item No-31.18 (vii)

ERECTION OF LIGHT FIXTURE Erection only of 1x40 watts or 2x40 watts 1220 mm long / Down Lighters fitting directly on wall including necessary connections with 0.75 sqmm (24 / 0.20 mm) PVC copper flexible cable for connecting the tube with the adjecent point. (complete as per HSR item No-31.18 (xxiv)

Erection of ceiling fan complete with necessary earthing of fan and regulator including carriage from local railway station /goods transport /PWD store to the site of work.(HSR No-31.20 (i)

Earth Connection for DB Providing and Laying Earth connection from Earth Electrode with 4mm Dia. GI Wire in 15mm Dia. GI Pipe from Earth Electrode as required.(HSR No-31.22 (xii)

Earth Connection for DB Providing and fixing 4mm Dia. GI Wire on surface or in recess for loop earthing as required.(HSR No-31.22 (xvi)

POINT WIRING Wiring with 1.5sq.mm (22/0.30mm) PVC insulated unsheathed stranded copper conductor cable ISI marked 1100 volts grade as per IS-694 in rigid PVC conduit pipe ISI marked medium (IS-9537) including bends, CI round inspection boxes, MS 18 S.W.G. Modular zinc coated boxes as per relevant IS codes alongwith all accessories including ISI Modular Switch/Socket, Modular Electronic Step Type Fan Regulator, Modular Cover Plates, 3mm thick Bakalite sheet to cover the Round CI junction boxes with Brass Screw & cup washers, Hexagonal GI Fan box, Steel pull wire, J-hooks and refilling the chases/cuttings with cement mortar having ratio 1:2 (1 Cement : 2 Coarse Sand) includes cost of all material, labour & taxes etc. Complete in all respect as required. (HSR No-31.36) FAN POINT(I) (b)Medium Point

FAN POINT (I) (c)Long Point

(II)LIGHT POINT (a)Short Point

(b)Medium Point

(c)Long Point

(IV)LIGHT POINT WITHOUT CONTROL SWITCH (a)Short Point

(b)Medium Point

(c)Long Point

(VII)3-PIN 5A, PLUG Point Including Earthing 3rd Point etc. (a)Short Point

(VIII)3-PIN 15A, PLUG Point with 4 Sq.mm PVC Insulated Copper Conductor Cable including earthing 3rd Point etc. (b)Medium Point

(c)Long Point

PVC CONDUIT Supply and erection of PVC conduit pipe ISI marked (Medium) recessed in wall / ceiling etc. including cost of PVC bends, inspection box and all other material requiredto complete the job in all respect to the entire satisfaction of Engineer-in-Charge of work.(HSR No-31.44) 20 mm dia HSR No-31.44(a)

25 mm dia HSR No-31.44)(b)

Switches and Sockets (for Computer Points) Providing & Fixing modular Type accessories of approved make in existing Box including fixing & making necessories connections complete in all respect. (2.5Sq.mm circuit wires shall be extra on measurement basis and JB's shall be extra) Make of Modular Switches and Sockets shall be as per Client approved make.(HSR No-31.56) 10A one way Switch (HSR No-31.56 (i)

10A Socket (HSR No-31.56 (ii)

PVC CONDUIT Supply and erection of PVC pipe ISI marked ( Medium ) recessed in wall / ceiling etc. including the cost of PVC bends inspection boxes , iron hooks, cement concrete etc. complete in all respect up to the entire satisfaction of engineer in charge of work.(HSR No-31.58) PVC pipe of 32 mm dia (HSR No-31.58)( i )

PVC pipe of 40 mm dia (HSR No-31.58)( ii )

COPPER WIRES Supply and erection of PVC unsheathed copper conductor cable single core 1100 volts grade in pipe of suitable size excluding cost and erection of pipe (Finolex / Havell`s /RR Cables Make only)(HSR No-31.40) Size 1.5 sqmm (3 / 0.81mm) for Point Wiring/Earthing (HSR No-31.40)(i)

Size 2.5 sqmm (3 / 1.05mm) for Circuit wiring (HSR No-31.40)(ii)

Size 4 sqmm (7 / 0.85mm) for AC / Power Points (HSR No-31.40)(iii)

Size 6 sqmm ( 7 / 1.05mm) for LDB incoming Cable (HSR No-31.40)(iv)

Size 10 sqmm (7/1.35mm) for Power DB incoming Cable (HSR No-31.40)(v)

COPPER THIMBLES Supply and erection of copper lugs including crimping etc.upto the entire satisfaction of Engineer-in-Charge of work.(HSR No-31.45) 1.5 sqmm to 2.5 sqmm (HSR No-31.45)(a)

4 sqmm to 6 sqmm (HSR No-31.45)(b)

10 sqmm (HSR No-31.45) C )

M.S. SADDLES & CLAMPS Supply and erection of MS sadles and clamps on wall / RCC parapit for fixing underground cable at at distance of 0.60 metre centre to centre fixed by means of rawl plug including the cost of all labour and material required to complete the job in all(HSR No-31.48)

M.S. BOX Supply and erection of MS box made of 16 gauge MS Sheet recessed in wall, with arrangement of fixing brass screws, 2 Nos. check nuts and one No. PVC bush of required size including all labour and material required to complete the job in all respect up to the entire satisfaction of Engineer-in Charge of the work.(HSR No-31.49) (ii)With GI coating (anodized) suitable for modular accessories.(HSR No-31.49)(ii)

ELECTRONIC FAN REGULATOR Supply and erection of socket size rotary step type electronic regulator for A.C. ceiling fan Anchor make Deluxe model no. 50440 ISI / SSK make PC 561 operated on 120/280 V AC supply complete including cutting of existing bakelite sheet and making necessary connections etc. upto the entire satisfaction of engineer in charge of work.(HSR No-31.55)

MODULAR GI BOXES Providing and fixing GI concealed sheet metal boxes inner and outer faceplate including concealing the box in wall and fixing in position with inner plate and face plate with all labour and material requiered to complete the job in all respect.(HSR No-31.57) 1 & 2 module (HSR No-31.57( i )

3 Modules (HSR No-31.57( ii )

4 Modules (HSR No-31.57( iii )

6 Modules (HSR No-31.57( iv )

8 Modules (HSR No-31.57)(v)

TV OUTLET POINT Supply, installation, testing & commissioning of TV outlet point (from Splitter box to outlet point) including RG-6 grade, 0.7 mm dia solid copper wire PVC insulated PVC sheathed, heavy duty PVC conduit, Modular outlet socket, modular plate cover, modular G.I. box of suitable size reuired to be concealed in wall/floor/slab, including termination of wire at both ends with ferruling, chasing of wall /floors and making good with sand, cement mortar, complete in all repect as required by the site Engineer-in-Charge. compelte as per NS item

PVC CONDUIT Supply and erection of PVC conduit pipe ISI marked (Medium) recessed in wall / ceiling etc. including cost of PVC bends, inspection box and all other material required to complete the job in all respect to the entire satisfaction of Engineer-in-Charge of work.(HSR No-31.58) (a)32 mm dia (HSR No-31.58)

LIGHT & FAN FIXTURE Supply of light fixture of following models (ref. Wipro/Legrand or equalent Make) as approved by the Engineer-in-Charge.(compelte as per NS item (i)32Watt Recessed LED Down Lightter for Auditorium Hall. (Reference Wipro Cat No. LD56-381-060-40-XX) (compelte as per NS item)

(ii)Step Light Fixture for Auditorium(compelte as per NS item)

(iii)40 Watt IP 40 4 Feet Led fixture with extruded aluminium housing (Wipro Cat. No LL24-541-XXX-57-XX), for Mess & Projector Room(compelte as per NS item)

(iv)15 Watt LED Down Lighter (for Auditorium Front Entrance)(compelte as per NS item)

(v)Mirror Light Fixture(compelte as per NS item)

(vi)1200mm Ceiling Fan White Model - WWPS-PS WOR CGL(compelte as per NS item)

(vii)Telephone Point SITC of Telephone Socket (RJ11) Single Module along with Cover Plate, to be fixed on the existing JB complete in all respect.(compelte as per NS item)

(viii) LAN Point SITC of Telephone Socket (RJ45) Single Module along with Cover Plate, to be fixed on the existing JB complete in all respect.(compelte as per NS item)

(ix)LAN Wire (DSR 2018 Item No. 1.53.1)(compelte as per NS item)

(x)Telephone Wire (2Pair) DSR 2018 item No. 1.18.2(compelte as per NS item)

Supply, installation, testing and commissioning of floor mounted Package Air Conditioner with multiple scroll compressors complete with indoor and outdoor units , interconnecting refrigerant piping, full charge of eco freiendly refrigerant gas & oil, control cabling,TF quality Canvass Connection and fittings etc. as per details given in specifications and having following items. The units shall be suitable for 3 phase 4 wire system, 415V + 10 %, 50 Hz AC supply ,Out door units shall be provided with MS stand of suitable size duly painted with corrosion resistant paint suitable for outdoor application and Indoor units shall be provided with high quality vibration pads at bottom of the machines All the units shall be provided with built-in microprocessor control panel, for automatic operation Insurance of Units ,Unloading at site, placement of Oudoor Units on the foundation,stands, co-ordination during execution, rendering necessary guidance for execution, supervision, testing, commissioning and startup of above mentioned Package ACs. Note: The civil foundations reqd shall be made by the tenderer i)17 TR Floor Mounted Package AC (Multi Scroll Compressor) Make:Voltas,Blue Star,Daikin,York,Carrier compelte as per NS item

Supply and Installation of Interconnecting Refrigerant Piping of various sizes as required for the full functionality of the Package AC system etc. complete in all respects duly insulated with Class O closed cell nitrile rubber as per specifications of the manufacturer. the contractor shall submit a detailed drawing approved by the manufacturer showing the piping sizes & layout to be followed at the site with the tender document. the contractor shall also get the drawings showing outdoor units in connection with indoor units approved from the HVAC consultant in original from and then the head office of the manufacturer with a certificate stating that the piping layout is as per company specifications for full functioning of the system. Make : Rajco/Mandev/Totaline (compelte as per NS item) i)19.1 mm OD (insulation = 13 mm)

ii)15.9 mm OD (insulation = 13 mm)

Ducting SITC of Factory/Site fabricated GSS Ducting complete with hanging arrangement of fasteners, GI threaded rods etc. (Make: Eco Duct/Zeco/GP Spira (Sheet Make: Tata, Sail,Jindel)compelte as per NS item i) 24 G (0.63 MM)

ii) 22 G (0.8 MM)

iii) 20 G (1.0 MM)

i) SITC of Nitrile rubber class-O/Closed cell XLPE Fire retardant insulation 9 mm thick pasted on the outer surface of duct with suitable adhesive complete in all respects with Nitrile tapes. (Armacell/K-Flex/Paramount)(compelte as per NS item

SITC of Acoustic lining of the supply duct with 10 mm thick Accosound Nitrile board with suitable adhesive to be pasted inside of the Plenum duct complete in all respects i) 10 mm thickness accosound Board Armacell/K-Flex/Paramount (compelte as per NS item

SITC of Expanded polystyrene (EPS) TF Quality 50 mm thick with density of 20kg/Cum with suitable adhesive (e.g. Shallimar/Bitumen) to be pasted on the surface of duct before putting EPS section on duct and after that this shall be covered with wiremesh .Then this shall be covered with a 7 mil fibre cloth fire proof & finally coated with two coats of ENCOAT star glue paint to give it a smooth finish complete in all respect as per satisfaction of EIC Make: Lloyed,Beardsell (compelte as per NS item

i) SITC of Aluminium extruded powder coated Grills for supply & return air w/o vcd Make:Tristar/Caryaire/Ravistar/Uniaire compelte as per NS item

ii) SITC of Aluminium powder coated Diffuser for supply & return air w/o vcd (Make:Tristar/Caryaire/Ravistar/Uniaire (compelte as per NS item)

Dampers i) Supply, installation, testing & commissioning of GI Collar dampers (compelte as per NS item)Make:Caryaire , Ravistar,Airflow, Tristar ,Uni Aire

ii) Supply, installation, testing & commissioning of CBRI approved Fire duct Dampers for at least 90 min fire rating as per UL555:1955 Specifications without Sleeve(compelte as per NS item) Make:Caryaire , Ravistar,Airflow, Tristar ,Uni Aire

iii) Supply, installation, testing & commissioning of Spring Return Actuator and Control Panel Complete with Heat Sensors , Complete Control wiring and Limit switch,4NM/7NM/9NM,(24VAC/220VAC)(compelte as per NS item) Make:Caryaire , Ravistar,Airflow, Tristar ,Uni Aire

Condensate Drain Piping: Providing UPVC pipes of various sizes for condensed water drainage from Indoor unit to nearest disposal point in toilet/ outside rain water harvesting system as approved by architect/ consultant/ Client All necessary civil works like cutting & chasing of walls/floor/ glass etc. and make them good thereof Make : Diplast/Supreme/Polyplast (compelte as per NS item) i) 40 MM DIA

ii) 32 MM DIA

Supplying and laying of following 1100 volt grade PVC insulated sheathed copper conductor armoured cables in trenches, on walls clamped to wall with suitable clamps, saddles, and fixing bolts, or laying in ground including cost of digging brick and sand protection, and including jointing / connecting / terminating, testing and commissioning :(Make : Havell's,Eko,Finolex,Polycab)(compelte as per NS item) i) 4C x 25Sq. mm Copper (armoured) Conductor

ii) 4C x 16Sq. mm Copper (armoured) Conductor

i) Providing & fixing of electrical supply Flexible Cabling of 4 core x 2.5 sq. mm copper in suitable conduits. Make : Havell's,Eko,Finolex,Polycab (compelte as per NS item)

ii) Providing & fixing control cum transmission wiring/ Control Cabling of 2 core x 1.5sq. mm copper in suitable conduits between indoor and out door unit & indoor unit & its remote controller. Make : Havell's,Eko,Finolex,Polycab(compelte as per NS item)

iii) Providing & fixing control cum transmission wiring/ Control Cabling of 4 core x 1.5sq. mm copper Make : Havell's,Eko,Finolex,Polycab(compelte as per NS item)

Providing and fixing of perforated type GI Cable Tray (1.5 mm thick) for Running Copper Refrigerant Piping of of Following Sizes including nut bolts G.I Thread rods Complete in all Respect(compelte as per NS item) ii) 50mm(H) x 300mm(W) x 50 mm(H).

iii) 50mm(H) x 150mm(W) x 50 mm.(H)

Main Electrical panel (CPRI approved) Electrical Main Panel weather Proof outdoor Type Powder Coated Made out of TATA/SAIL/ESSAR/JINDAL/Reputed make sheet having thickness 2.0 mm for load bearing surfaces & 1.6 mm Non bearing surfaces as per following specifications complete in all respect..INCOMING SUPPLY : MCCB 150-200 Amps,4 Pole 50 KA Micro Processor Based release Adjustable type (suitable atleast Ambient Temperature 50 degrees) The MCCB shall have ICS=100%ICU etc : 1 No.Multi Fuction VAF/VIF Meter (96mmX96mm Size) ,Indication Lamps LED Type RYB, Control MCB SP for Control (3 Nos each),CT's 200/5 (3 Nos) etc.OUTGOING FEEDERS :100A-125A,0-63A or suitable ,4.0/3.0 Pole MCCB,36KA with Thermal magenetic release adjustable type. The MCCB shall be double break & the ICS=100% ICU : (2 Nos + 1 Spare) along with requiredSpreader Links with phase Barriers , Rotary Mechanism,Auto phase Sequence relay,ATS etc. BUS BAR : Aluminium Bus Bar 300 A TPN Electrolite grade E91 having Suitable size Cross Section for Phase,Neutral& Current Carrying Capacity 0.8 A/Sqmm Hardware ( PVC Cahnnels/MCB Channels/Fibre- Glass Gaskets/Sleevs/nuts/bolt/washers/cooling fans etc Including complete wiring,thimbles etc. Unloading at site, placement of Panel on the foundation, co-ordination during execution, rendering necessary guidance for execution, supervision, testing, commissioning and startup of above mentioned Panel. Unloading at site, placement of Panel on the foundation, co-ordination during execution, rendering necessary guidance for execution, supervision, testing, commissioning and startup of above mentioned Panel. Panel Make : International Switchgear/Adlec/Siemens/Tricolite/Unitech Power System/Vrindavan Electricals/KEPL(compelte as per NS item)

ii) GI 8 SWG wire earthing complete with thimbles etc(compelte as per NS item)

iii) P/F of 25 X5 mm GI Strip earthing Complete with nutbolt,thimbles etc.

Civil Work for making Holes, Chiesling, Cutting walls etc. and make them good thereof(compelte as per NS item)

First aid hose reel pipe & nozzle , Providing and fixing of First Aid Hose Reel pipe 30 mtr. x 19mm pressure braided hose reel rubber pipe which kept wound with heavy duty gun metal shutoff nozzle of 5 mm dia.ISI MARKED

Providing, Fixing and Testing of following C.I Headed Oblique Type Hydrant Valves with Flanges inlet with 63mm, stop valve, spindle and cast iron hand wheel Female Instantaneous outlet of SS/G.M complete with plastic Blank Cap and chain. A) Single headed Hydrant Valve (compelte as per NS item)

Providing and Fixing of Outdoor Weather Proof Standard Hose Cabinet made of MS Sheet Painted Red outside and white paint inside to accommodate one hose pipe and branch pipe and Hinged Door with 2 mm Glass with locking arrangement. (MAKE:- Atasi.)

Providing of GM/Al nozzle having 63 mm dia. instantaneous type male inlet and on the other side a hexagonal nozzle of 20 mm dia. Bore which gives a jet of water. Branch Pipe. (MAKE: Atasi.)

Providing, Fixing and Testing of Two Way Fire Brigade Inlet which is connected to underground Hydrant main pipe line outside the building.(Atasi)

Providing, Fixing and Testing M.S pipe including fixing the pipe after Painted Two Coats of Red Oxide and Postman Red Paint and also rates inclusive of MS Pipe in all kind the same after doing anti- corrosive treatment .(Make:-Jindal,Apollo general)

A) 100 mm (In mtrs.)

B) 80 mm (In mtrs.)

C) 50 mm (In mtrs.)

D) 32 mm (In mtrs.)

E) 25 mm (In mtrs.)

Providing and Fixing of ball valve of the following dia. Sizes complete with bolts, nuts, washer as Required. A) 25 mm (Gun metal gate valve)

Supplying, Installation, Commissioning &Testing of Electric Driven Main Pump Set. The pump will be of centrifugal type. The pump and motor will be fixed on common bed plate of suitable M.S. Channel / brick foundation provided by the client.(Make:-Lubi) 5hp

Providing and Fixing Cast Iron Double Flanged Type Butterfly Valve/ Wafer Type as of following dia. sizes complete with bolts, nuts, washers and rubber gaskets as required. (Make:-Jamco/Nvr).

providing, testing and commissioning of Microprocessor based 4/6 Zones Main Fire Alarm Control Panel complete with zones and visual indication of fault and fire including 24v DC for supply and charger including all material and labour required for installation/ testing etc. Complete in all respect up to the satisfaction of person in charge of auto delivery work. (Make: AGNI)

Providing of material for fixing all material e.g. S.S flexible pipe for Sprinkler bend,flange,nipple,socket,nut-bolt,channelsupport,rod,fastner,unioun,tank nipple valve etc.

Supplying & Fixing of flexible 2 core plain cable two colour wire suitable to operate fire alarm system complete in all respect

Supplying & Fixing of 75 mm pvc conduit pipe ISI MARKED

Supply, testing and commissioning of low intensity electronic Hotter Speaker with line matching transformer at working voltage of 24v DC for Fire Alarm & including all material and labour required for installation/ testing etc. Complete in all respect up to the satisfaction of person in charge of work. (Make: AGNI)

Supply, testing and commissioning of Manual Call Points (Make: AGNI)

Material for fixing fire alarm system e.g. junction box,screw,flexible pipe, bends etc

Providing 63mm dia.15mtr long RRL Hose Pipe with SS/C.I Male & Female Coupling wound with GI Wire complete as required

Providing, testing and commissioning of Photoelectric/ lionization type Smoke Detector complete with base LED (light emitting diode) with accessories including all testing etc. Complete in all respect up to the satisfaction of person in charge of work. (Make:-Atasi, Apollo, Agni.)

Providing & fixing of multipurpose ISI MARKED fire extinguisher Cap 6 kg complete in all respect.

Providing and fixing of 15mm dia. Gunmetal quick response quartzoid bulb type sprinkler head suitable to operate at 68 degree Centigrade.(Make: Aqua/Swastik/Globe/Atasi)

Nain Construction Company