Construction of various balance works at District Hospital Ganderbal

Amount

Earth work in bulk excavation by mechanical means (hydraulic excavator) over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 m2 on plan) including disposal of excavated earth lead upto 50 meters and lift upto 1.5 m, as directed by as directed by All kinds of soil :

Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 meters lead as per direction of Engineer-in-charge.

Providing and laying of stone soiling hand packed tightly including loading, unloading and all carriages upto site of work completed.

Providing and laying integral cement based treatment for water proofing on the vertical surface by fixing specified stone slab 22 mm to 25 mm thick with cement slurry mixed with water proofing compound conforming to IS:2645 in recommended proportions with a gap of 20 mm (minimum) between stone slabs and the receiving surfaces and filling the gaps with neat cement slurry mixed with water proofing compound and finishing the exterior of stone slab with cement mortar1:3 (1 cement : 3 coarse sand) 20mm thick with neat cement punning mixed with water proofing compound in recommended proportion complete at all levels and as directed by Engineer-in-Charge: 23.2.1 Using rough kota stone.

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level steel bars Hard drawn steel wire Hot rolled deformed bars

Providing and laying cement concrete in kerbs, steps and the like at or near ground level including curing, excluding the cost of centring, shuttering, and finishing. 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)

Centering and shuttering including strutting, propping etc and removal of form for:- . Lintels, Beams, plinth beams, Girders, bressumers and cantilevers

Supply and filling of Nallah muck including ramming and rolling with road roller or hand roller including all carriages involved complete job

Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. Polished Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent.

Chequerred terrazzo tiles 22mm thick with graded marble chips of size upto 6mm in floors, jointed with neat cement slurry mixed with pigment to match the shade of the tiles, including rubbing, polishing and curing complete, on 20 mm thick bed of cement mortar 1:4 ( 1 cement : 4 coarse sand) . Light shade using white cement

Providing and laying 60mm thick factory made cement concrete interlocking paver block of M-30 grade made by block making machine with strong vibratory compaction and of approved size and design/shape laid in required colour and pattern over and including 50mm thick compacted bed of fine sand, filling the joints with coarse sand etc. all complete as per direction of Engineer-in-charge.

Providing and fixing aluminum work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixed with dash fastener of required dia. and size including necessary filling up of gaps at junctions i.e, at top, bottom and sides with required EPDM rubber / neoprene gasket felt etc. Aluminum sections shall be smooth, rust free, straight, mitered and jointed mechanically wherever required including cleat angle, Aluminum snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge (glazing, paneling and dash fasteners to be paid for separately.) fixed with portions.

P/F of wire gauge mesh in aluminum shutters as per directions of Engineer I/C including of all necessary fixtures /materials/fittings required for the same (complete job)

P/F of 4mm thick Aluminum partition panel (APP) Alstone of Equivalent make with rubber gasket and aluminum snape beading etc complete job

Providing and fixing glazing in aluminum door, window, ventilator shutters etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge. (Cost of aluminum snap beading shall be paid in basic item.)

P/F of aluminum composite panel (ACP) 4mm thick to interior /exterior surfaces for concrete walls /columns /beams and AC pipes etc to the surface for goodlook including all necessary frame work and filling up of gaps of joints with silicon complete as per the design and directions of the Engineer I/C (Alstone make) complete job

Providing and fixing in position collapsible steel shutters with vertical channels 20x10x2mm and braced with flat iron diagonals 20x5 mm size, with top and bottom rail of T-iron 40x40x6mm, with 40mm dia, steel pulleys, complete with bolts, nuts, locking arrangement, stoppers, handles, including applying a priming coat of approved steel primer,

Providing and laying Vitrified tiles in floor with different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS: 15622, of approved brand and manufacturer, in all colours and shades, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS: 15477, in average 6 mm thickness, including grouting of joints (Payment for grouting of joints to be made separately). Size of tile 600x600 mm.

Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS:15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer- in-Charge, in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 ( 1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm, including pointing.

Brick work with common burnt clay (non modular) bricks of class designation 7.5 in foundation and plinth including curing in cement mortar 1:6 (1 cement: 6 coarse sand) including extra for brick work in super-structure above plinth upto floor- V level.

15mm cement plaster on rough side of single or half brick wall of mix 1:6 ( 1 cement 6 coarse sand)

Providing and applying plaster of pairs putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete.

Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surfaces.

Providing and applying white cement based putty of specified thickness, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Finishing with epoxy paint (two or more coats) at all locations prepared and applied as per manufacturers specifications including appropriate priming coat preparation of surface, etc complete on wall surface.

P/F of SS railing with top railing of 50mm 16 guage vertical baluster of 40mm and height 2'-9" after every two sets enshrouded in thread with fasternal and lead coloured and 3 No of horizontal runner dia fixed all along the railing and fixed of master piller of stain less steel 75mm, (height 3'-10") JINDAL MAKE 304

P/F of SS hand rail 50mm dia 16 guage JINDAL-304 make fixed on wall side including all necessary fittings for embedding with side walls complete.

Structural steel work in built up sections, tursses and framed work including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete ( welded)

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, including cutting and making good the walls etc.:

32 mm dia. nominal bore

50mm dia G.I Pipes

20mm dia G.I Pipes

Providing and Fixing of pre-coated galvanized iron profile sheets ( size, shape and pitch of corrugation as approved by Engineer I/C 50mm ( + .05%) total coated thickness with zinc coating 120grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 micron expoy primer on both sides of the sheet and polyester top coat 15-18 microns. sheet should have protective guard film of 25microns minium to avoid scratches during transporation and should be supplied in single lenght upto 12mtr as desired by Engineer I/C the sheet shall be fixed using self-drilling /self-tapping screws of size 5.5x55mm) with EPDM seal, complete upto any pitch in horizental /vertical or curved surfaces excluding the cost of prulins , rafters and trussed and including cutting to size and shpe wherever required

P/F of 12mm thick 600mm wide soffit of T&G imported wood paneling including erection, fixing, and applying of pu polishing coat ,complete as per specifications including jam work(1.5"x3" of budloo wood) underneath complete

Providing and fixing plained eaves boarding. 300x40 mm (nominal size)

Providing and fixing of colour coated panelling Type CGI sheet of including cost of underlying budloo wood frame work complete including cost of scaffolding nails etc complete job.

Providing and fixing of stainless steel plano plate of Jindal make 11.81kg/ sq. metre make 304 of 16 guage for expansion joints fixed in floors by way of stainless steel screws and mchored at both sides by using of araldite including cost of drilling, including labour for loading, unloading and carriage complete job.

Providing and fixing of bed consoles made up of budloo wood frame work of 19mm thick ply board laminated/ summica/ dulmica sheets in portions including cost of wood along half height, dash fasteners, nuts glass panes for lightening boxes SR solution fixed etc including cost of carriage all material to site of load upto 2nd floor and also including cost of all labour carpenter charge complete. bed consoles to be majored in finished measured in finished form including polishing all our surface.

Providing and fixing of Aluminum 0.5mm tin foil insolation to cover of heating pipes used as heat insolation include. Cost of necessary frame work of aluminum tube and aluminum angle ( 25x25x1mm) at the exposed edges and also including scaffolding charges complete.

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade.

engagement of labours for clearance of toilet blocks/ bathrooms/ halls by way of removing debris, unservicable material including its disposal upto lead of 150 mtrs complete job.

Providing, laying, fixing and jointing of G-I pipes conforming IS 1239 heavy duty class C (PRAKASH SOURAYA) make with G.I fittings, unions, clamps complete including cost of cutting of holes and making good same.

32mm nominal bore G.I Pipes

50mm nominal bore G.I Pipes

Providing and fixing, testing of PVC finolex pipes along with all required fittings like tees, bends, cross door joints with approved solvents cement fixed to walls and ceilings with clamps complete job including cost of cutting of holes and making good same.

Providing and fixing of flush values make jaquarwar including cost of all materials complete job.

Providing and Laying in position cement concrete (Cast in situ)of specified grade excluding the cost of centering and shuttering- All work up to plinth level: in 1:3:6 (1 Cement: 3 coarse sand (zone III): 6 graded stone aggregate 40mm nominal size).

P/F of CP Brass wall mixer basin mixer, sink mixer, with all accessories including cost of nipples etc complete (jaqwar cat No. 167 KB)

wall mixer

sink mixer

basin mixer

P/F of CP Brass Angle valve(Jaquar) of 15mm nominal bore dia with C.P copper connecting pipe complete job including cost of C.P nipples, cutting holes and making good the same. (jaquar cat No. 037 KB)

P/F of CP Brass bib cock (jaquar) of 15mm nominial bore dia with C.P copper connecting pipe complete job including cost C.P nipples, cutting holes and making good the same. (Jaquar cat No. CON 037 KN) Jaquar make

P/F of CP Brass Soap case including cost of all accessories complete job.

III) P/F of CP Brass 100mm dia C.P grating Grating including cost of all accessories complete job

P/F CP Brass towel raing including cost of all accessories complete job.

Providing and fixing 600x450 mm bevelled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P.brass screws and washers complete.

Providing and fixing Stain less Steel A lSI 304 (18/8) kitchen sink as per I.S. 13983 with C.l. brackets and stainless steel plug 40 mm including painting of fittings and brackets,600x460mm bowl depth 200mm Jindal make

Providing and fixing of vitreous wash basin flate back pattern with C. I./M.S. brackets,15mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required: White Vitreous China wash basin siz 550x400 mm with single 15 mm C.P. brass pillar taps including cost of Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back ,for the reception of pipes and fittings.

Providing and fixing of vitreous china wash basin under counter mounting with single lever basin mixer with C. I./M.S. brackets, 15mm C.P. brass pillar tape, 32 mm C.P. brass waste of standard pattern, rubber plug with C.P brass chain, C.P wall flange and rubber adopting for water connection complete.

Providing and fixing white vitreous china pedestal type (European type/wash down type) water closet pan including cost of colored pedestal type W. C Pan (European type) with low level cistern of same colour complete job including cost of all accessories, cutting holes and making the same good.

Providing and fixing white vitreous china water closet squatting pan (Indian type) Orissa pattern W.C. pan of size 580x440 mm make hindware (Cat 20042) including cost of all materials, accessories, cutting holes and making the same good.

5.P/F OF STORAGE TYPE VERTICAL HOT WATER HEATER(Geyser) with copper container, insulation stove enameled thermostatically controlled immersion heater with pilot neon lamps suitable length of electric cable,3 pin plug top,15mm dia PVC connections at the outlet (Venus, Racold, Havells) make 35 LTR. Capacity

providing and fixing of health fauset including cost of plumbing, accessories complete job.

Providing and fixing of white colour china urinal partitions of height 810 mm complete including cutting and making good the walls (parry ware model code 0507)

Providing and fixing of automatic flushing systern for indiviual urinals (610x390x380mm) hindware cat No 60007 to ensure flushing only when in use comprising of all plumbing including cost of all materials

The bidder shall quote his rate including all sorts of carriages, loading, unloading, dumping and head load complete upto site of work.

M/S DAR CONSTRUCTIONS

M/S ALI MOHD SOFI