REPAIR TO DRAIN COMPOUND WALL FENCING HARD STANDING IN SARAGARHI COMPLEX AND REPAIR MAINT OF MES INSTALLATION BUILDINGS POWER HOUSE AT MRS OVER HEAD TANK PUMP HOUSE SUMP IN AGE BR I UNDER GE MIS MHOW

Amount

Site Clearance by cutting all bushes, shrubs, any type of vegetation etc complete all as specified and directed and removing the same to distance exc 500 m but n exc 1500 m out side MD land complete all as specified and directed

Dismantling posts or struts ( steel or R.C.C.) any section, including taking out embedded portion in concrete and making good disturbed ground etc complete all as specified and directed

Dismantling of GI plain/ GI barbed wire any description complete all as specified and directed

Dismantling fencing wire mesh,any type complete all as specified and directed

Demolition of brick work built in cement mortar of any description including all quions, arches and pillar etc complete all as specified.

Taking down cement plaster from brick or concrete surface including racking out joints hacking for key and scrubbing down with water complete all as specified.

Demolition of cement concrete in ground floors and pavings not exc. 15 cm thickness (below/above ground level) including floor finishes all as specified and directed

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. and getting out in any type of soil complete all as specified and directed

Removing excavated material (soil) to a distance exc.500 m and not exc 1500 m out side MD land and depositing where directed at a level n exc 1.5 m above the starting point complete all as specified and directed

Returning, filling in soil including spreading, levelling, watering and well ramming in layers not exc 25 cm.complete all as specified and directed

M&L for PCC 1:4:8 type D2 (using 40mm graded stone aggregate) as in foundation concrete ,mass concrete etc complete all as specified and directed

M&L for brick work with fly ash bricks, straight or curve on plan exceeding 6m mean radius built in CM 1:4

M&L for PCC 1:2:4 type B1 (using 20mm graded stone aggregate) as in pillers, post and coping including necessary form work finished even & fair complete all as specified and directed

M&L for rendering 15mm thick in CM 1:4 on brick or concrete surfaces mixing with water proofing compound and finished even and smooth without using extra cement complete all as specified . (Note:WPC shall be measured and paid separately).

M&L for TMT steel bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips all complete all as specified and directed

S&F mild steel angle iron (Fe-310) as in posts, struts,flat iron ( for securing wire mess etc ) in fencing including cutting top to shape required, drilling holes, notching for wire,erect & fixed in true position etc complete all as specified and directed

Supply only galvanised chain link fencing, any size or type, complete all as specified and directed.

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails straining bolts, etc including provision of binding wirecomplete all as specified and directed.Note: MS screw ,bolts etc shall be measured and paid separately under relevant item as supply only.

Supply only MS screw, bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut exceeding 5cm and not exceeding 10cm long and dia complete all as specified and directed

M&L for applying two coats of synthetic enamelled paint over a coat of red oxide primer including preparation of new steel/iron surfaces exceeding 10cm in width or girth.complete all as specified and directed

M&L for applying two coats of synthetic enamelled paint over a coat of red oxide primer including preparation of new steel/iron surfaces not exceeding 10cm in width or girth.complete all as specified and directed

Preparation of brick masonary / concrete wall surfaces, plastered / unplastered surface and applying two coats of exterior weather proof water base emulsion paint over a coat of primer of same make on walls complete all as specified and directed (Make : Shalimar, Saktiman/ Asian- ACE/Burger wal masta or other equivalent as approved by GE)

S&F Galvanised. 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails straining bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. as directed (each line wire to be measured)

M&L for applying two coats of synthetic enamel paint on steel surfaces of any description, not otherwise described over 10cm in width or girth incuding preparation of old steel surfaces.

M&L for applying three coats of white wash on wall on old plastered / concrete sufaces incuding preparation of surfaces.

M&L for hardcore with broken stone of gauge n.exc.63mm deposited,spread and levelled in in layers n.exc 15cm thick,watered and rammed to a true surface

M&L for 100mm thick cement concrete 1:4:8 type D2 (using 40mm graded aggregate) as in sub base including use and waste of form work and finished concrete surface even and rough to receive topping layer

M &L for 75mm thick cement concrete 1:4:8 type D2 (using 40mm graded aggregate) as in sub base including use and waste of form work and finished concrete surface even and rough to receive topping layer

M&L for machine pressed coloured precast concrete interlocking paver block rubber moulded (glossy finished) any shape and size confirming to IS 15658-2006 of 60 mm thickness M35 Grade, laid over stone dust cusion and jointed with filled with sand complete all as specified and directed.(Note: stone dust cushioning shall be measured and paid separately under relevant item.)

M&L for machine pressed coloured precast concrete interlocking paver block rubber moulded ,any shape and size confirming to IS 15658-2006 of 100 mm thickness, M50 Grade, laid over stone dust cusion and jointed with filled with sand complete all as specified and directed.(Note: stone dust cushioning shall be measured and paid separately under relevant item.)

M&L for stone dust for bed cushioing ot tiles including watering and consolidation spreading and levelling complete all as specified and directed

S&F precast cement concrete 1:2:4 type B0 (using 12.5mm garded stone aggregate) jallies, 40mm thick,including all moulding and set in CM 1:4 including demolition of old broken existing RCC jallies complete all as specified.

M&L for RCC 1:2:4 type B1 (using 20mm graded stone aggregate) as in lintels over 1.5m span ,coping ,beam.etc.complete .Note:Reinforcement shall be measured and paid separately under relevant item.

M&L for use & waste of timber formwork to sides and soffits of coping ,beam for rough finished surface.

M&L for mild steel TMT bars 8mm dia and over,cut to length,bent to shape required,including cranking,bending spirally for hooping ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips as in stirrups.

M&L for mild steel TMT bars 8mm dia and over,cut to length,bent to shape required,including cranking,bending spirally for hooping ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips.

M&L for precast reinforced cement concrete 1:2:4 type B1 using 20mm graded stone aggregate as in cover slabs for manholes including necessary formwork and set in cement mortar 1:4.Note:Reinforcement shall be measured and paid separately under relevant item.

M&L for 50mm thick sand stone slab in as in manholes cover stone of size not less than 0.60m x 1.20 m ,set and pointed in CM 1:4

M&L for PCC 1:2:4 type B1using 20 mm graded stone aggregate as in drains and surface channels and finished even and smooth complete all as specified and directed by Engineer-in-Charge.

M&L for extra for forming fair finished drain or channel 30cm inner girth in cement concret, using extra cement, including forms, moulds, initred/stopped ends.

M&L for add or deduct for Sl. Item No 40 above for each 25 mm girth or part there of over or under 30 cm

Demolition of cement concrete (un-reinforced) of any description and in any position not otherwise specified complete all as directed.

Dismantling floor or wall tiles including cement mortar bedding, removing serviceable tiles to store and rubbish off the premises complete all as specified and directed

Taking down shutters of any description area exceeding 1.00 Sqm but not exceeding 2.0 Sqm all as specified and directed.

Dismantling mild steel work of any description from any position and height as directed and specified.

Dismantling of Asbestos cement (corrugated, semicorrugated, etc.) sheets in roof coverings complete all as specified and directed.

Dismantling of Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillet complete.

Demolition of stone slabs, paving stones and tiles of any description and thickness in floors, aprons, laid, bedded and pointed in any mortar complete all as specified and directed.

M&L for rendering 15mm thick plaster in CM (1:6) on fair faces of brick work or concrete surfaces, finished even and smooth without using extra cement complete all as specified and directed.

M&L for preparation of new plastered surfaces of walls and applying two coats of oil bound distemper over a coat of alkali resistance primer complete all as specified and directed.

M&L for preparation of new plastered surface of wall and applying two coat of exterior weather proof water base emulsion paint over a coat of primer of same make on wall as specified and directed (Make :- Asian-Apex/Berger- Weather antidust/Nerolac-Excel/Dulux-Weathershield).

M&L for brick work with modular size burnt clay bricks, straight or curved on plan exc. 6 m mean radius built in cement mortar (1:6), complete all as specified

M&L for PCC (1:5:10) type E2 using 40mm graded stone aggregate in foundations, filling and mass concrete, sunken floors complete all as specified and directed.

M&L for 75 mm thick PCC (1:3:6) type C2 (using 20mm graded stone aggregate) as in plinth protection including making joint at every 3 m interval and at corner and filled with mixture of bitumen and sand and finished even and fair and laid in alternate bays complete all as specified and directed.

M&L for plain cement concrete (1:2:4) type B1 using 20mm graded stone aggregate, 40mm thick as in floor, coping, finish the surfaces even and smooth with using extra cement complete as specified and directed.

M&L for glazed ceramic coloured tiles of size 450mm x 300 mm x 6 to 7mm thick in dados or skirting over & including rendering 10mm thick in CM (1:4), jointed in neat grey cement slurry and pointed in colour cement to match the tiles all as directed and specified.

M&L for Non skid ceramic tiles coloured, 7 to 8 mm thick (Square / rectangular ) area of each tile exceeding 0.11 Sqm but n. exc 0.18 Sqm, over & including 20mm thick screed bed in CM (1:6) in floors etc set and jointed in neat cement slurry and pointed in coloured cement to match the tiles all as directed and specified.

S&F PVC door frames of sizes 50mm x 47 mm made out of 5 mm prelam PVC sheet reinforced with MS Square tube in opening of suitable size complete all as specified and directed.

S&F Factory made (Prelam on both sides) solid panel PVC door shutter 30 mm thick (Style) consisting of frame made out of MS tubes for top and bottom rails, MS frame shall covered with heat moulded prelam PVC 'C' channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for styles and prelam PVC sheets for top rail, lock rail and bottom rail in either side and as gap insert for top rail and bottom rail pannelling of prelam PVC sheet to be filled in the MS welded/sealed to the styles and rails with suitable PVC sheet beading and jointed together wiht solvent and fixing in the frame at site as per specification and drawing complete all as specified and directed.

S&F mild steel roof trusses, trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc conforming to Fe-410-w Gde-E-250 Quality-A complete all as specified and directed.

S&F mild steel framed work such as grills,gratings etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165.

S&F Mild Steel work with hollow MS tubular section square or rectangular section as rafter/purlin including necessary welding bolting complete with using ERW or induction butt welded tubes confirming to relevant I.S. Fe 410 -W (Gde?E- 250) quality?A complete all as specified and directed

S&F Pre painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tesile strength of 550 Mpa as in roof covering to wall, fixed with self tapping screws as specified

S&F Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering / cladding to wall, and eves board fixed with self tapping screws as specified

S&F Anodised aluminium snap grid of size (605mmx605mm) frame work for false ceiling with Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified.

S&F exposed metal frame ceiling with calcium silicate board of siliceous and calcareous material reinforced with cellulose fibre for fixing in 600 mm x 600mm grid complete all as specified. (Note:Frame work for ceiling shall be measured and paid separately)

M&L for Machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab inclunding rubbing and polishing complete including screed bed 15mm thick in CM (1:6) complete all as specified and directed.

All as per item no 67 above but as in skirting over and including 10mm thick rendering in CM (1:4 ) complete all as specified and directed.

M&L for polishing of existing Kota stone flooring with mirror finish as specifeed and directed

M&L for chequered cement concrete tiles of size 40cm x 40cm x 25 to 30mm thick (Glosy finished) with grey cement and pigment, including 15mm thick screed in CM 1:6, set jointed & pointed in neat cement slurry in floors and cut & polished complete all as specified and directed.

M&L for machine pressed precast concrete interlocking paver block rubber moulded (glossy finished) any shape and size confirming to IS 15658-2006 of 80 mm thickness, M40 Grade with grey cement and pigment laid on stone dust cushioning laid dry to the profile complete all as directed.(Note: stone dust cushioning over will be measured & paid seperately.

Excavating in post holes (or similar holes) each n exc 0.5 cum, getting out in any type of soil including returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25cm, watering, and removing surplus soil to a distance n exc 50 m and making good surface etc complete.

M&L for plain cement concrete (1:3:6) type C2 using 40mm graded stone aggregate as in in foundations, filling and mass concrete etc complete.

S&F in repair mild steel work as in Hooks and Pintle hinges for steel gates including necessary weling, cutting holes in wall,making good the same with PCC 1:2:4 type B1 and applying two coats of painting & wall finish to match with the existing complete all as specified and directed.

S&F precast cement concrete louvres and jallies, 35mm thick with cement concrete 1:2:4 type B0 (using 12.5mm graded stone aggregate) set in cement mortar (1:4) including all mouldings but excluding frame

S&F Reinforced concrete pipes 300 mm bore class NP2, laid and jointed complete with collars

M&L for Reinforcement cement concrete 1:2:4 type B1 using 20 mm graded stone aggregate as in foundations, footings of columns etc.complete all as specified and directed.Note:Reinforcement shall be measured and paid separately under relevant item.

M&L for Reinforcement cement concrete 1:2:4 type B1 using 20 mm graded stone aggregate as in columns, pillars, piers posts and struts etc.complete all as specified and directed. Note:Reinforcement shall be measured and paid separately under relevant item.

M&L for Reinforcement cement concrete 1:2:4 type B1 using 20 mm graded stone aggregate as in beams, lintels, copings etc.complete all as specified and directed.Note:Reinforcement shall be measured and paid separately under relevant item.

M&L for use and waste form work to sides of concrete foudations, footings for flat and rough finished surfaces of concrete complete all as specified and directed.

M&L for use and waste form work to sides of columns, pillars posts struts for flat and rough finished surfaces of concrete Complete all as specified and directed.

M&L for use and waste form work to soffits and sides of beams, lintels etc. for flat and rough finished surfaces of concrete complete all as specified and directed.

S&F 110mm PVC SWR pipes single socketed in any length with rubber ring joints, laid in trenches or in floor complete all as specified.

S&F PVC (SWR) bends any radius 110mm dia.

S&F PVC (SWR) single tee equal 110mm dia.

M&L for preparation of old decorated plastered or unplastered surfaces by brooming down or steel wire brushing, scrapping down smoke soot, moulds, mass and efflorescent salts and trading oil and greasy spots and evenly applying two coats of white wash on surfaces of walls etc complete all as specified and as directed.

All as per item No. 86 above but one coat of white wash on ceiling complete all as specified and as directed.

M&L for washing rubbing down and stopping distempered surfaces of walls etc and evenly applying one coat of distemper oil emulsion distemper all as specified and directed

M&L for preparation of old painted wood & wood based surfaces of any description, not otherwise described over 10cm in width or girth and evenly applying one coat on synthetic enamel paint complete all as specified and directed

M&L for writing building numbers including letters or figures,symbols etc 10mm wide, not exceeding 65mm height (Block. Roman. Italic or Indian) with synthetic enamel paint over and including black synthetic enamel paint back ground of 150mm dia including obliterating old writting of any description description n exc 0.10 sqm with paint to match existing surface complete all as specified and as directed. Note :- Letters,numbers ,shapes,symbol etc not exceeding 10 Nos shall be measured as one unit

Sree Ram Enterprises

M/s Himgiri construction

Messers Yogendra Kumar Sankhla

M/S Sunshine Construction

APconstruction