REPAIR MAINT ANDREPLACEMENT OF EXT LT ELECTRIC SUPPLY NETWORK LIGHTNING CONDUCTORS AND PARAMETER LIGHTS HIGH MAST LIGHTS ETC AND OTHER CONNECTED ITEMS AT DHAR ROAD SAMNABANJ RC PEAK BATTAL UNDER GE ARMY DHAR ROAD

Amount

Excavation in trenches not exceeding 1.5 meter wide and not exceeding 1.5 meter in deep getting out in soil for stay assembly/laying of cable/errection of poles etc complete all as specified and directed.

All as per item No 1 above but depth exceeding 1.5 meter and not exceeding 3 meter complete all as specified and directed.

Returning, filling in including spreading, levelling, watering and well ramming in layers n.exc 25cm thick.

Removing of excavated material n.exc 50m and depositing where directed at a level n.exc 1.5m above the starting point.

PCC (1:3:6) type C-2 using 40mm graded aggregate as in foundation for filling in, mass concrete for foundation of Pole, Transformer, Panel board, stay, post top lantern, repairs to road cutting, drain, path etc complete all as specified and directed.

PCC (1:2:4) type B-1 using 20mm graded aggregate as in coping of new pole / reconstruction old damaged copings etc, including necessary form work complete all as specified and directed

M & L for dry Sand cushioning in trenches for protection of cable including watering and consolidation all as specified and directed. Note: Punned thickness shall be considerd for measurment purpose

M & L for well burnt brick sub class B old size laying in trenches perpendicular to axis of the cable complete all as specified and directed.

Supply and laying in trenches/Floor or fixed to Pole/Wall GI pipe light grade with fitting of size 40 mm bore for protection of cable including dismantling existing pipe complete all as specified and directed by the Engineer-in-Charge.

All as per item No 09 above but of size 50 mm bore.

All as per item No 09 above but of size 80 mm bore.

All as per item No 09 above but of size 100 mm bore.

M&L for cutting of PCC/Hard standing/WBM road not exceeding 20 cm in width not exceeding 30 cm in depth for passing of LT cable and making good of disturbed surface to match with the existing surfaces by using old and new material i.e bitumen/PCC (1:3:6) type C-1 complete all as specified and directed .

Taking out existing worn out/old PVC insulated cable in 3.5 core of 185 /240/400sqmm size of 1100 Volt grade in pieces from trenches making loop for transportation and removal from site after taking proper shut down from MES compitent staff complete in all respect and as directed at site.

Taking out existing worn out/old PVC insulated cable in 3.5 core of 70/95/120/150 sqmm to 35 Sqmm size of 1100 Volt grade in pieces from trenches making loop for transportation and removal from site after taking proper shut down from MES compitent staff complete in all respect and as directed at site.

Taking out existing worn out/old PVC insulated cable of 10/16/25/35/50 sqmm any type of 1100 Volt grade in pieces from trenches making loop for transportation and removal from site after taking proper shut down from MES compitent staff complete in all respect and as directed at site.

Material and labour for fixing or passing through pipe, laid in trenches or fixed to pole/wall or fixed to LT panel board, XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 10 sq. mm x 2 Core with required aluminium cable lugs all as specified and directed by EIC. Make: Finolex/Polycab /Grandlay Cables” Note: Product authentication and warranty to be provided by the local representative of the concerned company on OEM letter head pad.

-- do-- as per item no. 17 above but of size 16 sq mm 2 core

-- do-- as per item no. 17 above but of size 16 sq mm 4 core

-- do-- as per item no. 17 above but of size 25 sq mm 3.5 core

-- do-- as per item no. 17 above but of size 35 sq mm 3.5 core

-- do-- as per item no. 17 above but of size 50 sq mm 3.5 core

-- do-- as per item no. 17 above but of size 70 sq mm 3.5 core

-- do-- as per item no. 17 above but of size 95 sq mm 3.5 core

-- do-- as per item no. 17 above but of size 120 sq mm 3.5 core

-- do-- as per item no. 17 above but of size 150 sq mm 3.5 core

-- do-- as per item no. 17 above but of size 185 sq mm 3.5 core

-- do-- as per item no. 17 above but of size 240 sq mm 3.5 core

-- do-- as per item no. 17 above but of size 300 sq mm 3.5 core

-- do-- as per item no. 17 above but of size 400 sq mm 3.5 core

Taking down old UNSV panle any type and shape and supply , installation, testing and commissioning as in repair busbar chamber, outdoor type, double door,KIOSK type of size (0.6x0.60 x 0.25) Mtrs, factory made, front & back openable, properly welded MS angular supported with Stand made out of 50x50x6 mm thick angle iron having 4 Nos legs of 3 feet height with CRCA steel sheet Minimum of 3 mm thick, duly painted internally and externally with two coats of synthetic enamel paint over a coat of red oxide primer of any tint, CPRI Approved with locking arrangements with & including 4 Nos Aluminium busbar of rating 250 Amp on base insulators including necessary platform and grouting of panel as per manufecturer's instructions after demolition of chamber as existing at site complete all as specified and as directed.

Taking down old UNSV panle any type and shape and supply , installation, testing and commissioning as in repair busbar chamber, outdoor type, double door,KIOSK type of size (0.60x0.40 x 0.20) Mtrs, factory made, front & back openable, properly welded MS angular supported with Stand made out of (45x45x6) mm thick angle iron having 4 Nos legs of 2.5 feet height with CRCA steel sheet, minimum of 2mm thick , duly painted internally and externally with two coats of synthetic enamel paint over a coat of red oxide primer of any tint, CPRI Approved with locking arrangements with & including 4 Nos Aluminium busbar of rating 200 Amp on base insulators including necessary platform and grouting of panel as per manufecturer's instructions after demolition of chamber as existing at site complete all as specified and as directed.

Supply and fix as in repair of Cable jointing kit for 11 KV (Earthed) grade cable for straight through heat shrink type joint complete with jointing material and accessories suitable for 3 core XLPE armoured aluminium conductor cable of size 95 to 120 sqmm

S&F Cable jointing kit for 11 KV (Earthed) grade cable for heat shrink type end joint in door type complete with jointing material and accessories suitable for 3 core XLPE armoured aluminium conductor cable of size 95 to 120 sqmm

S&F Cable jointing kit for 11 KV (Earthed) grade cable for heat shrink type end joint out door type complete with jointing material and accessories suitable for 3 core XLPE armoured aluminium conductor cable of size 95 sqmm

S&F Cable jointing kit for 11 KV (Earthed) grade cable for heat shrink type end joint out door type complete with jointing material and accessories suitable for 3 core XLPE armoured aluminium conductor cable of size 120 sqmm

Dimentling and taking down old/unsv cross arms, bracing, supports etc complete all as specified and directed.

S&F cross arms bracings supports clamps and back plates fabricated from structural steel sections including nuts, bolts, washers, welding bending cold or hot, drilling holes for bolts in any shape or size as indicated or directed and inclusive of one primer coat, one under coat and one finishing coat of aluminium paints complte all as specified and directed.

Dismetling and taking down old/unsv ACSR conductor any size complete all as specified and directed.

S/F ACSR conductor incl jointing with existing conductor and straining on LT pole and proper fastening to pin/shackle insulators with aluminium binding wires and required jumpering connection all as dercted. Note :- Size of aluminium conductor as per site requirement will be directed by Engineer-in-Charge.

Dimentling and taking down old/unsv insulator of any type any size from pole/stay complete all as specified and directed.

S&F as in repair of Disc type insulator 11000 volts porcelain, vitrous 145mm high and 255 mm dia ball and socket type white, brown or green single disc with tension clamp for conductor for working pressure voltage 11000 V all as spd and directed.

S&F as in repair of pin type 11000 Volts, porcelain, vitreous, brown, including one galvanised mild steel spindle, two galvanised iron washer and one galvanised iron nut, 150mm height and 150 mm dia for 11000 volts grade all as specified and directed.

removing and dismentaling of Stay assy and S& F as in repair using 16mm dia galvanised rod complete all as shown in electrical plate No 1 of SSR Part I including clamp, loop, insulator etc. (PCC and earth work will be measured separately)

S/F for stay wire using galvanised steel strand of 7/3.15mm complete with necessary binding incl dismentling taking down unserviceable one all as specified and directed

M & L triple pole mechanically operated GOD mounted on insulators and steel frame with operating mechanism worked from ground level 11000 volts grade of current carying capacity up to 200 Amps complete incl removing the existing U/S one.

M & L for Earthing complete with galvanised steel earth plate electrode 6mm thick of size 600x600 mm buried directly and vertically in ground with top edge of the plate not less than 2.25 mtr from GL, connected with galvanised iron strip 32x6mm all as shown in Plate No-3, connected to the earthing test point, concrete pit in PCC 1:3:6 type C-2with RCC precast pit cover slab 400mmx400mmx50mm with handle for lifting made out of 8mm dia MS rod, funnel, wiremesh, 50 mm dia light grade GI tubing for protection of GI Strip 32x6mm, charcoal and salt in alternate 150mm thick layers around GI earth plate, including necessary returning filling in & removal all as specified or indicated in SSR Part-I, including testing to achieve earth resistance value as per IS specification on completion

Supply and fixing GI strip 32 x 6 mm for extension of earth and connected to equipment or panel complete all as specified and directed by Engineer-in-Charge.

M&L for restraining of overhead ACSR conductor of any size 03 to 5 conductor on pole after disconnecting all jumpering connection & binding of insulators and redoing all jumpering connection and insulator binding with aluminium conductor providing required T&P all as specified and directed

S&F MCCB 400 Amps 4 Pole, 35 KA, 415 V, 50 Hz adjustable type and connecting up in the existing panel location including taking out existing unserviceable MCCB complete all as specified and as directed by Engineer-in-Charge.

All as per item No 50 here in before but MCCB 250 Amps 4 Pole, 25 KA, 415 V, 50 Hz complete all as specified and directed.

All as per item No 50 here in before but MCCB 200 Amps 4 Pole, 25 KA, 415 V, 50 Hz complete all as specified and directed.

All as per item No 50 here in before but MCCB 160 Amps 4 Pole, 25 KA, 415 V, 50 Hz complete all as specified and directed.

All as per item No 50 here in before but MCCB 100 Amps 4 Pole, 16 KA, 415 V, 50 Hz complete all as specified and directed.

All as per item No 50 here in before but MCCB 63 Amps 4 Pole, 16 KA, 415 V, 50 Hz complete all as specified and directed.

M&L for painting and write pole number of steel tubular pole with one coat of alumium paint incl cross arm, bracings, supports, nuts, bolts, of LT/HT OH line from above copping to top of pole and marking with alternate white and yellow/black paint strip 30 cm wide (5 Nos) with synthetic enamelled paint all as specified and directed.

M&L for trimming of branches of trees touching LT/HT electric over head line and making clear about 3 mtr in radius by climbing up tree or by providing ladder, at a height 7 mtr and above and carrying and depositing where directed not exceeding 50 mtr.

S&F of lightning arrestor, distribution class, System voltage-11KV, min rating-10KV, Discharge cap-10 KA, Line discharge class-1 complete with bracket and connection complete all as specified and directed.

M&L for taking out cable loop after excavtion near panel/pole after taking shut down, cutting and setting aside burnt cable ends/lugs and peeling off insulation of cable upto required length for making connection at pole or insertion of new cable lugs in cable, creaming properly and making connection in panel, fedder piller box junction box and tightning with and including new bolts nuts & washers of required complete all as specified and directed by Engr - in -Charge.

T&P and labour for cutting /uprooting /bushes /shrubs /grass /saplings /plant /trees etc not more than 3.0mtr high and setting aside not less than 50mtr away from single pole of 3 sqmtr complete all as specified and directed by the Engineer-in-Charge. Note:- The jobs shall be repeated at same location after 3 months

Supply, Errecting and fixing of true Vertical position steel tubular swaged pole complete with coat iron base plate, finial taper plug, bolt, nuts and screw,weld and reduced section and logitudional weld Seam through out entire length of pole including 2 coats of black bituminious paint through out intrnely and externely up to planting depth and remaining exterior portion of pole with two caot of aluminium paint over a coat of red oxide as specified type 410 SP 31 (9.00 Mtr long) incl taking down old unserviceable pole all as specified and directed at site. NOTE - Excavation and Earth work and PCC in foundation shall be measured and paid seprately.

Supply, Errecting and fixing of true Vertical position steel tubular swaged pole complete with coat iron base plate, finial taper plug, bolt, nuts and screw,weld and reduced section and logitudional weld Seam through out entire length of pole including 2 coats of black bituminious paint through out intrnely and externely up to planting depth and remaining exterior portion of pole with two caot of aluminium paint over a coat of red oxide as specified type 410 SP-55 (11.00 Mtr long) incl taking down old unserviceable pole all as specified and directed at site. NOTE - Excavation and Earth work and PCC in foundation shall be measured and paid seprately.

Material and labour for shifting of poles by disconnecting all electrical connection/light/bracket taking out pole safely and refixing it to other location as directed by EIC. Note- the job include excavation/returning and filling and disposal for removing/fixing of pole, dismentalling and making of new PCC in foundation and coping etc , transportaion will be responsibilaity of contractor complete all as spd.

Dismantling and taking out existing unserviceable street light fittings / flood lights/Post top lantern of any type from pole /high mast/ bldgs incl brackets and electric connections complete

Taking down old unserviceable driver for street/flood/post top lantern light fittings etc

S&F LED street light fitting 90 Watt with min lumen output 10800 LM , toughened glass , pure polyester power coated pressure die cast aluminium housing, silicon gasket provided for LED and control gear compartments , LEDs are provided with non yellowing modular secondary lens, optics, , CCT 5665 ±355K, CRI >70, 50000 Burning Hrs, Built-in Surge protection 4 kV, THD<10%, Ingress Protection IP 66, Impact protection IK07, Power factor > 0.95, external surge protection 10Kv complete all as specified and directed Note: Product authentication and warranty to be provided by the local representative of the concerned company on OEM letter head pad.

S&F LED street light fitting 70/72 Watt with min lumen output 9100 LM , pressure die cast aluminium housing, whether proof gasket provided for LED and control gear compartments , LEDs are provided with non yellowing modular secondary lens, optics, , CCT 5665 ±355K, CRI >70, 50000 Burning Hrs, Built-in Surge protection 4 kV, THD<10%, Ingress Protection IP 66, Impact protection IK08, Power factor > 0.95, external surge protection 10Kv complete all as specified and directed Note: Product authentication and warranty to be provided by the local representative of the concerned company on OEM letter head pad.

Supply and fixing of Security Light 45 W, Epoxy powder coated pressure die-cast aluminium Housing, Weatherproof gaskets provided for LEDs and control gear compartments, LEDs are provided with non-yellowing modular secondary lens optics, lumious flux 4550 Lm, CCT 5665±355K, CRI >70, 50000 Burning hrs, Built-in Surge protection 4kV, External Surge Protection 10kV, Ingress Protection IP66, Impact Protection IK08. complete all as specified and directed” Note: Product authentication and warranty to be provided by the local representative of the concerned company on OEM letter head pad.

GI bracket 1.5 mtr long made out of 40mm bore light grade, GI pipe, bend to shape as required complete with two Nos MS clamps fabricated out of MS flat of size 40 x 5 mm, nuts and bolts duly painted with two coats of aluminium paint of superior quality over a coat of red oxide primer, to be fixed on pole/on roof of building including taking down old brackets complete all as specified and directed by the Engineer-in-Charge.

Supply and fixing of Flood light 120 W Toughened glass with Secondary lens optics, Graphite grey powder coated matt finished pressure diecast aluminium housing designed to act as heat sink for efficient dissipation of heat & luminous flux 9600 LM, CCT 5665±355K, CRI >70, 50000 Burning hrs, Built-in Surge protection 4kV, External Surge Protection 10kV, Ingress Protection IP66, Impact Protection IK07, Beam Angle (±10%) 60°. complete all as specified and directed”. Note: Product authentication and warranty to be provided by the local representative of the concerned company on OEM letter head pad.

Supply,fixing, connecting, testing and commissioning Flood light 200 W Toughned glass with Secondary lens optics, Graphite grey powder coated matt finished pressure diecast aluminium housing designed to act as heat sink for efficient dissipation of heat, & lumious flux 24000 LM, CCT 5665±355K, CRI >70, 50000 Burning hrs, Built-in Surge protection 4kV, External Surge Protection 10kV, Ingress Protection IP66, Impact Protection IK08, Beam Angle (±10%) 60° complete all as specified and directed. ”. Note: Product authentication and warranty to be provided by the local representative of the concerned company on OEM letter head pad.

Supply and fixing of Post Top 40 W, Luminous flux 4000 lm, CCT 5665K ±355K, CRI >70, 50000 Burning hrs, Built-in Surge Protection 4 kV , External Surge Protection 10kV, Ingress Protection IP65, Impact Protection IK06, Diffuser : PC Opal for LED section & PC clear for housing, Spun aluminum black powder coated housing with PDC bottom incl dismantling and taking down unsv fitting any type all as specified and directed..” Note: Product authentication and warranty to be provided by the local representative of the concerned company on OEM letter head pad.

Supply and fixing street light junction box of suitable size for single phase and neutral incl earth link cable connection outdoor type, weather proof, factory made out of PVC sheet 1.8 mm thick with front side hinged opening having locking arrangement with nuts & bolts & arrangement for incoming and out going cable/wire complete comprising with the followings :- (a) Bus bar with two numbers aluminium strips, 100 Amps capacity insulated with insulators, including colour coding strip, including PVC cable of suitable size from bus bar to MCB (b) MCB SPN 6 to 30 Amps - 01 No (c) Clamps made out of 40mm x 5mm flat iron duly welded with nuts & bolts complete all as specified and directed including taking down old unserviceable .

Supply and fixing Street light fitting electronic constant current drivers/PCB/electronic gear suitable for 40 to 60 Watt LED flood light/street light fitting as required at site or as per sample incl taking out old unserviceable all as specified and directed .

Supply and fixing Street light fitting electronic constant current drivers/PCB/electronic gear suitable for 70 to 90 Watt LED flood light/street light fitting as required at site or as per sample incl taking out old unserviceable all as specified and directed .

Supply and fixing Street / flood light fitting electronic constant current drivers/PCB/electronic gear suitable for 120 to 150 Watt LED flood light/street light fitting as required at site or as per sample incl taking out old unserviceable all as specified and directed .

Supply and fixing Street light/flood light electronic constant current drivers/PCB/electronic gear suitable for 200 Watt LED flood light/street light fitting as required at site or as per sample incl taking out old unserviceable all as specified and directed .

PVC insulated, PVC sheathed twin flat core 1100 volts grade, 4 sqmm aluminium conductor from OH conductor or from junction box to street/security light incl taking down old unserviceable cable all as specified and directed.

Supply and laying or fixing or passing through pipe from junction box to street light connection, 1100 volts grade heavy duty cable with PVC solid insulated aluminium conductor served with an inner sheathing PVC tape and over all PVC sheathed 6 Sqmm 2 core (TC) nominal cross section incl taking down old unserviceable complete all as specified and directed.

Supply and fix as in repair Globe light Weldecor Unbreakable Gate Lamp Polycarbonate Doom ,Round Shaped Globe Light complete all as spd and directed by EIC

supply and fix as in repair Stareagle EGL 502 -LED Square Bollard Led,E27 CFL Holder, Outdoor Grey Body for Garden Park Driveway Light - Warm White (300 BL) or equavallent.

Earthing complete with galvanised steel earth plate electrode 600 x 600 x 6 mm thick buried in ground vertically to a depth not less than 2.25 mm below ground level with top edge of the earth plate not less than 1.5 mm below normal ground level, connected to GI strip 32 x 6 mm continuity conductor including 40 mm bore pipe light grade for protection of strip by means of bolts, nuts, check nuts and washers made out of galvanised iron or steel connected to earth test point upto 7.5 mt away from earth electrode all as shown as per plate No 03 of SSR I including necessary earth work, PCC 1:3:6 type C 1 chamber, RCC cover slab of 50 mm thick 1::2:4 with 8 mm CTD 140 mm C/C with suitable handle,watering pipe 20 mm dia light grade pipe with funnel,. charcoal salt and testing on completion and including taking old unserviceable earthing with connected items all as specified and directed by Engr in charge including taking down old/unsv earthing.

S & F in replacement air termination single pointed aluminium rod 12 mm dia and 300 mm long fitted on exisiting lightening conductor tube 40 mm on buildings with F clamps nut bolts complete all as specified and directed.

S & F in replacement earth test point terminal block made out of gun metal or phorphorus bronze size 75 x 75 x 5 mm , drilled and screwed including 3 Nos 8 mm dia 25 mm long hexagonal head screw grouting on wall with PCC, nut bolts and washers, including making good to disturbed surface complete all as specified and directed.

S&F Galvanised iron strip 32 x 6 mm for extension of earth and connected to equipment or panel complete all as specified and as directed .

S & F in repairs aluminium strip 25 x 3.0 mm with saddle and fixing screws, gutties etc on wall and roof top conductors including grouting wooden gutties complete all as specified and directed.

Taking out old handing GI strip (damaged by Monkey ) and refixing properly from roof well complete excluding straightening the strip and refixing in the same position with saddle fixing screws gutties etc on wall and roof op conductors including grouting wooden gutties complete all as specified and directed.

S & F GI tubing light grade 40 mm bore fixing in bricks/stone wall with 2 Nos sopporting clamp made of flat iron of size 25 x 4 mm including nut bolt and grouting bolt complete all as specified and directed for fixing lightening arrester on roof top.

S&F GI tubing light grade 40 mm bore fixing including grouting in PCC complete all as specified and directed for fixing leghtening arrester on roof top.

Supply and fix single automatic street light switch suitable for 3KW load complete with two numbers infrared sensor based NATURE SWITCH for automatic switching of street/ security lights with one number two pole power contractor 40 Amps (Type MU40-2P, Cs90119) with coil voltage 220/240 V and incoming MCBs single pole - 01 No, outgoing MCBs single pole - 01 No of rating 32 Amps & circuit wiring with single core multi standard of size 10 sq mm lighting switch operation should be based on natural light lux level, Required luminance level for switching ON is < 30 Lux. The sensor (one service and one stand by) should also have part night operation facility for 4,5,6---11&12 hours. The sensor along with suitable power contractor (S), incoming and outgoing MCBs should be enclosed in a pole/wall mountable enclosure made of Rust proof, Electric shock proof, termite proof and FR grade confirming to IP66 complete all as specified and directed by Engineer in charge.

Repair to hight mast light by lowring of over all assembly and repair , removal and re fixing of after maint of high mast light head, high mast light ring, repairing of motor, chain , steel rope and other nut bolt and placing back to its original position complete all as spd and directed by EIC. Note - High mast light head, high mast light ring, steel rope will be measured and paid separately.

Supply and fixing Stainless Steel wire rope of 6mm dia complete all as spd and directed by E-in-C

Supply and fixing as in repair of high mast head suitable for 16/18 Mtr high mast light having 6/8 Nos of Lantern along with nut bolt and washer complete all as directed by EIC

Supply and fixing as in repair high mast light ring suitable for 6/8 lantern along with nut bolt washers complete all as spd and directed by EIC

Deduct Schedule of Credit of Rs. (-) 119766.00 (Minus) as listed in Schedule 'A' Part-II. Contract Sum shall be arrived after deducting the credit amount Note: Tenderers will not quote against this item being a firm amount.

M/s Ranpat Dev Infrastructure pvt ltd (BID ID -3301309)

K S BUILDERS (BID ID -3299541)

M/SHansrajbuilder (BID ID -3299572)