Fabrication And Erection Jobs of Morinda CSM

Amount

Morinda CSM

Replacement of worn-out of M.S. Runner of PCC, SCC, ICC, Elevator, RBC and cross carrier chains

Replacement of S.S. tubes of all juice heaters, vapour line juice heater and semi-Kestner.

-do- but the number of tubes below 50 no.

-do- but all pans during off-season

-do- but evaporators during off-season

- do – but in case of entire body of evaporator

Welding joints of water, juice, vapour and exhaust pipe lines of all sizes.

Pipe line upto 12” dia a) Dismantling

b) Erection

Pipe line above 12” dia from MS plate a) Dismantling

b) Fabrication

c) Erection

Bends from readymade pipe line up to 12" dia a) Dismantling

b) Fabrication

c) Erection

Bends above 12” dia from MS plate a) Dismantling

b) Fabrication

c) Erection

Tee, Nipples & Crosses upto 12” dia a) Dismantling

b) Fabrication

c) Erection

Tee, Nipples & Crosses above 12” dia from M.S Plate a) Dismantling

b) Fabrication

c) Erection

Reducers of all sizes, a) Dismantling

b) Fabrication

c) Erection

Flanges of all sizes, a) Dismantling

b) Fabrication

c) Erection

Valves: a) Dismantling

b) Fabrication

c) Erection

Man Holes of all sizes a) Dismantling

b) Fabrication

c) Erection

Platform: a) Dismantling

b) Fabrication

c) Erection

M.S. Structure work Light a) Dismantling

b) Fabrication

c) Erection

M.S. Structure work Heavy a) Dismantling

b) Fabrication

c) Erection

M.S. Tank complete having round & conical & rectangular bottoms a) Dismantling

b) Fabrication

c) Erection

M.S Rubber seated valves of any types a) Dismantling

b) Fabrication

c) Erection

NRV of any type: a) Dismantling

b) Fabrication

c) Erection

Platform Pipe Line railing of all sizes a) Dismantling

b) Erection

Fabrication of S.S rubber seated valves and NRV of all sizes

M.S. Patch work

Fabrication and Erection M.S. stair; a) Monkey tower type

b) Step type

Repair of rubber seated valves above 12" dia

Repair of NRV valves above 12" dia

Straightening M.S plate

Strengthening of any structure with M.S Angle/Channel

S.S. to S.S. welding

Fabrication and erection of all type of pump + motor bed.

Repair of cane un-loader grab arms

Drilling and Tapping of Mill’s top roller of square end face having size 8-20M at 265 PCD and 50mm deep thread for fitting of Ropeless coupling.

Repair and overhauling of Cane unloaders except hydraulic grab.

Replacement of cane cutting knives of chopper

Replacement of cane cutting knives of swing type cutter

Replacement of Fibrizer hammers with tip

-do- but only Domite tips

Dismantling, fabrication & erection of mills juice tray (M.S. Plate)

Fabrication of SCC and inter carrier chain’s rake.

Repair of Secondary Cane Carrier & inter Carrier Chain’s rake.

Hard facing of TRPF rollers

To build mills top rollers square end as per standard size

To build mills roller crown pinion teeth as per standard template of teeth.

-do- but mill roller coupling square section as per standard size

Fabrication of TRPF juice tray

Fabrication of TRPF top roller cover

Dismantling, fabrication and erection of Donnelly chute of mills

To build up the TRPF roller journal as per standard size.

To build up the mill roller journal as per standard size.

Fabrication and erection of mill roller crown pinion guard

Fabrication and erection of TRPF roller crown pinion guard

Complete repair of TRPF pressure chute, including replacement of worn out S.S. Plate

Fabrication of Mill top roller scrapper assembly as per existing size & design

Fabrication of discharge roller scrapper assembly.

Replacement of worn out bottom boot of inter carrier chain.

Replacement of Cast Iron Furnace chute of J.T. and Texmaco Boilers.

Fabrication of RBC slats made out from 3 mm thick plate for both RBC Chain

Repair of RBC Slat

Replacement of M.S. Bagasse chute of J.T. and Texmaco Boilers.

Replacement of worn out furnace door of J.T. boilers without frame

Replacement of worn out furnace door frame

Repair & fitting of furnace door of Texmaco/JT boiler

a) Fabrication of steam drum partition Plates of Boilers

b) Repair of steam drum partition Plates of Boilers

Boiler damper a) Dismantling

b) Fabrication

c) Erection

Repair of ID fan of J.T & Texmaco boiler

Repair of FD fan of J.T & Texmaco boiler

Replacement of worn out stainers of various types such as juice pump, lime pumps and syrup pumps.

Complete replacement of worn out save-all of evaporator bodies in all respects.

Complete replacement of worn out save-all of pans in all respects.

Replacement of worn out vapour pipe of various sizes of pans going to condenser

Replacement of worn out steam/water coil of Ordinary design size - 1/2'' to 3''

do- but 4'' to 6''

Replacement of worn out steam/water coil of Pure circular design size - 1/2'' to 3''

do- but 4'' to 6''

Dismantling, fabrication & erection of bends of pan’s vapour pipe line leading from body shell to condensers. Rates to be quoted in terms of :- Full Bend:- size 900 mm

Half Bend:- size 900 mm

Replacement of gutters a) Dismantling

b) Fabrication

c) Erection

a) Replacement of worn out stirrer arms (Straight Type)

b) Replacement of worn out stirrer arms (Worm Type)

Replacement of worn out umbrella of pans

Replacement of all pipe line of sulphur burners cooler, complete in all respect.

Replacement of worn out portion of sulphur burner cooler inside pipeline.

Complete replacement of worn-out after burner of Sulphur furnace i.e including the replacement of internal pipe line also

Dismantling, Fabrication and erection of sulphur burner melter of sulphur furnaces.

Replacement of worn-out Bagacilo pipe line made out from G.I. plain sheet of standard size

Replacement of Y type steam connection for syrup and molasses tank at pan station

Replacement of vacuum filter agitator

Fitting & modification of Planetary gear box along with dismantling of existing gear system. a) 80 Ton

Replacement of worn out partition plates of headers of juice heaters, complete in all respect.

Replacement of S.S pipeline of any size: a) Dismantling

b) Fabrication

c) Erection

Lowering the height of evaporator body no. 1 similar to level of evaporator body no. 2 including water levelling and fitting of all connections.

Repair of vapour line juice heater’s header cover: Scope of work includes: a) Dismantling, facing/machining header cover. b) S.S. lining of header cover by 6mm thick plate with duly facing and levelling. c) Fitting of existing cover plate after completion of the above mentioned work.

a) Replacement of Hopper trough

b) Replacement of complete portion of Hopper tray

Replacement of molasses chute of ; a) Continuous Centrifugal machine

b) Batch type Centrifugal machine

Replacement of any worn out shell portion of pug mills/magma mixers.

Modification of cooling coils of overhead crystallizer into air cooled type.

Fitting the complete magnetic separator system at Sugar Hopper tray.

Dismantling of Existing, obsolete AAW machines including all accessories i.e. pugmill, structure, elect. Panel etc. along with motors.

Dismantling of Existing, obsolete AFW machines including all accessories i.e. pugmill, structure, elect. Panel etc. along with motors.

Fabrication & erection of cable tray

Replacement of Thimble (Any Size)

Checking of cable connections, cleaning of thimbles & reconnection

Replacement of switches/MCCB 630 AMP, 400 AMP, 250 AMP

Replacement/erection of changeover switch 630 AMP/400 AMP/ 250/ AMP

APW ENTERPRISES

TANVEER ALAM