CA NO. GE AF NO.1/GUR-41/2024-25 REPAIRS TO PLASTERING, FLOORING, ROLLING SHUTTER AND JOINERY INCLUDING CONNECTED BR WORKS IN MES INSTALLATIONS AT AF STN GURGAON UNDER GE (AF) GURGAON NO. 1.

Amount

Demolition of cement concrete in ground floors and pavings n exc 15cm thickness (below or above ground level) complete all as specified and as directed.

M&L for PCC 1:2:4 type B1 using (20mm graded stone aggregate) as in cills, copings, small plates including weathering slightly rounded or chamfered angles and throating including necessary form work complete all as directed by Engr-in-Charge.

M&L for PCC 1:4:8 type D-2 using 40mm graded stone aggregate as in foundation ,filling and mass concrete completed all as specified and as directed by Engr-in-Charge.

M&L for pre cast kerb stone with plain fair faces 300x150x300 mm depth of PCC 1:1 ½ :3 of shape as approved incl all excavation, embedding in ground and removing surplus spoil upto 50 Mtr distance completed all as specified and as directed by Engr-in-Charge.

M&L machine cut broken stone of gauge not exc 63mm as in hard core n exc 150mm thick spread and levelled including watering & ramming all as directed by Engr-in-Charge.

M&L for 100mm thick plain cement concrete type B-2 1:2:4 using 40mm graded stone aggregate in sub-floors, sub-base, floors and paving etc complete all as directed by Engr-in-charge

M&L for 60mm thick machine pressed pre-casted cement concrete inter locking paver blocks glazed coloured up to 6mm on the top in any shape and size, strength not less than M-35 completed all as specified and as directed by Engr-in-Charge.

M&L for sand filling under floors or in foundations including watering & consolidation complete all as specified and directed.

M&L for 75mm thick plain cement concrete 1:4:8 type D-2 using 40mm graded stone aggregate as in sub base of floor complete all as specified and directed by Engr-in-Charge.

M&L glossy chequered cement concrete tiles 300x300x25mm thick, set jointed and pointed in near cement slurry in floors with white cement and pigments in any colour machine preassed glazed , over cement screed bed 15mm thick cement motor 1:6 all as specified and as directed by Engr-in-charge.

Dismantling, floor, hearth or wall tiling including cement mortar bedding (but not backing) and rubbish off the premises completed all as specified and as directed by Engr-in-Charge.

M&L joint free for 16-18 mm thick machine cut kota stone slab flooring in patches over 15 mm thick thick cement screed bed in CM 1:6 and jointed with gray cement slurry mix with pigment to match the shade of slab including rubbing and mirror type polishing complete all as directed by Engr-in-Charge.

M&L for glazed ceramic colour designer concept glazed ceramic tiles 200x300x7mm or 450x350x 7mm size as in walls set and jointed in neat cement slurry over and including 10mm thick Rendering in cement mortar (1:3) and pointed in coloured cement to match for work on vertical surface such as skirting, dado etc complete all as specified and as directed by Engineer-in-Charge.

M&L for joint free coloured non skid coloured ceramic tiles 7 to 8mm thick (squar / rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm in floors etc set and jointed in neat cement slurry and pointed in white/coloured cement to match over and including 15 mm thick screed bed in cement mortar in (1:6) complete all as specified and as directed by Engineer-in-Charge.

M&L Cutting and grinding mirror polishing old kota stone flooring including applying cement slurry to fill the existing joints completed all as specified and as directed by Engr-in-Charge.

Taking out the existing paver blocks of any size and set and jointed again in the same position after cleaning of grass and other vegitation etc all as directed and specified by engr in charge.

Taking down existing bitumen felt roof treatment including cement mortar bedding and cleaning the surface and removal outside the MoD land, complete all as specified and directed.

M&L for 40mm thick PCC (1:2:4) type B-1, using 20 mm graded mechanically crushed stone aggregates as in padding to roof to maintain the required slope and finished the surface even and smooth without using extra cement, complete all as specified and directed.

Material and labour, 10 mm thick cement plaster in CM (1:3) mixed with WPC as per manufacturer’s instructions on concrete surfaces, finished even and smooth without using extra cement complete all as specified and directed. Note : WPC shall be measured and paid separately.

M&L water proofing treatment of roof consisting as under:- (a) Applying evenly a coat of bituminous primer conforming to IS-3384:1986 @ 0.30 litre/sqm including preparation of roof surfaces (b) Applying evenly a tack coat of industrial bitumen 85/25 @ 1.2 kg/Sqm on plaster surface all as specified. (c) A layer of 3mm thick APP polymeric membrane of weight not less than 3.00 kg/sqm, reinforced with polyester non-woven fabric (weight not less than 150gm/sqm), duly sealed at over laps & joints with end laps of the 10cm and side over laps of 7.5cm by flame (by torch application) all as per manufacturer’s instructions, complete all as specified and directed.

Supply only water proofing liquid compoundcomplete all as specified and directed by Engr-in-Charge.

M&L for appling one coat aluminium heat resistance paint on the roof as per manufacture instructions complete all as specified and directed by Engr-in-Charge.

Dismantling of brick work built in cement mortar including all quions, arches, pillars, etc.completed all as specified and as directed by Engr-in-Charge.

M&L for Brick work with sub class B bricks straight or curved on plan exc 6 mtr mean radius built in CM 1:6 completed all as specified and as directed by Engr-in-Charge.

Taking down cement or cement lime plaster of any description on bricks wall etc including raking out joints, hacking for key, scrubbing down with water etc all as specified and directed by Engineer-in-Charge

M&L for 15mm thick rendering on brick or concrete surfaces in CM 1:4, finished even and smooth (without using extra cement) and using WPC as per manufacturers instruction complete all as specified and directed by Engineer-in-Charge. Note:- WPC shall be measured and paid seperately.

M&L 15mm thick rendering other then fair faces of brick work or concrete surfaces in CM 1:6, finished even and smooth (without using extra cement) all as specified and directed by Engineer-in-Charge.

M&L 5 mm thick rendering on ceiling etc surfaces in CM 1:3, finished even and smooth (without using extra cement) all as specified and directed by Engineer-in-Charge.

M&L for preparation of new plastered surfaces walls and cornices and applying two coat of acrylic emulsion paint over one coat of primer including necessary scaffolding all as specified and directed by Engineer-in-Charge.

M&L for Preparing New Plastered Surfaces of WALLS and applying TWO COATS of DISTEMPER OIL EMULSION (OIL BOUND WASHABLE DISTEMPER) over a Coat of CHALK WHITING, complete all as specified and as directed. by Engineer-in-Charge. (Note:- work will be strictly executed by mechinised means/ tools as required for smart periodical services).

M&L for Preparing Newly Plastered Surfaces of ceiling and applying Three COATS of WHITE WASHING, complete all as specified and as directed. by Engineer-in-Charge.

M&L for complete removal of existing treatment from old decorated plastered surfaces of walls by Vacuum based sanding machine complete all as specified, removal of nails etc & filling cracks/hole with putty, applying wall care putty upto 1mm thick as required (multipurpose mixer shall be used for uniform and proper mixing of putty) and applying two coats oil emulsion distemper white or coloured over a coat of approved primer by auto roller complete all as specified & directed by Engineer-in-Charge.

M&L Preparation old decorated surfaces on ceiling and cornices, spoiled by smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots by scraping and washing with water and applying two coat of white wash complete all as specified and directed by Engineer-in-Charge.

M&L for complete removal of existing treatment from old decorated plastered surfaces of walls by Vacuum based sanding machine complete all as specified, removal of nails etc & filling cracks/hole and applying two coat of acrylic emulsion paint over one coat of primer including necessary scaffolding all as specified and directed by Engineer-in-Charge.

M&L Preparation of old painted steel surfaces of any description not otherwise described, over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed by Engineer-in-Charge.

Dismantling structural steel work including steel door, gate, window guard bars, grills etc. complete all as specified and directed by Engineer-in-Charge.

Mild steel plates, plain or chequered, 5mm thick or over in thickness in available sizes Fe 410 W (Gde-E-250) quality-A with riveted bolt or welded etc as in duct cover & similar work completed all as specified and directed by Engr-in-Charge

S&F Steel work in tubular trusses, pillars and purlins including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S 1161-1979 grade St.-240 all as specified and directed by Engr-in-Charge.

M&L for mild steel Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted,or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and as directed by Engr-in-charge

S&F for MS angle iron as in posts, chowkhats and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire etc flat iron fillets (for securing with mesh etc including all necessary drilling bolting or riveting etc and similar work confirming to Fe-290 (Gde-E-165 quality-B. Note:-Posts/struts of angle iron made to shape shall be welded to existing angle iron bracket of security wall, contractor shall make his own arrangement for welding for boundary wall by using gen sets or any alternative arrangement.

S&F 1mm mild steel, plain black sheet hearths; covering to door shutters; covering to door chowkats (frames); chullah hoods; waters tanks; water troughs; ducts; urinal troughs and funnels, etc. cut to size, edges beaded if directed, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel members, etc., with plain 40mm lap joints or welded/riveted seams including bending, turning up, mitred angles, stopped ends, outlets, etc. as required and directed.

M&L Preparation new steel surface exc 10 cm width/girth and applying two coat synthetic enamal paint over one coat red oxide primer complete all as specified and directed by Engineer-in-charge

S&F in repair Galvanized 2 stand Steel Barbed wire 2.24mm dia barbed with dia barbs at 75 mm spacing and straining and fixing to any type of stsnderd rails, straining bolts,including securing or tying at crossings with and provisuion of galvanised mild steel pins, etc incl taking down of existing barbed wire as directed (each line wire to be measured) complete all as specified and directed by Engr-in- Charge

S&F in repair 950/650/450 mm dia (as directed by Engr-in-Charge) concertina coil reinforced punched(chrome razor or blade wire with barbed top of 0.5mm thick galvanised sheet and core wire of dia 2.5mm of high tensile steel wire incuding galvanised MS staples/ Clips for tying at crossing complete including taking down of existing concertina coil all as specified and directed by Engineer–in-Charge

Dismantling of Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings complete all as specified and as directed by Engr-in-Charge.

S&F 0.50 mm thick pre -painted galvalume aluminium zink coated GI based corrougated steel sheeting or curved shape of any colour having tansile strength of 550 MPA as in roof covering/glading to wall fixed with self tapping screws, complete all as specified and directed by Engr-in-Charge.

S&F 2 mm thick fibre glass reinforced translucent corrugated/ plain sheeting with two corrugations side lap fixed with coach screw and washer in roof, wall etc all as specified and directed by Engr-in-Charge.

Supply only Chain link MS galvanised fencing, any size or type all as specified and directed by Engr-in-Charge.

Fixing only Chain link MS galvanised fencing, any size or type including line wires, any mesh, standartds rails, straining bolts etc including provision of binding wire complete all as specified and directed by Engr-in-Charge.

M&L expanded metal not exc four kg per sqm, cut to length, bent to shape required and tying with and including annealed muild steel wire not less than 0.9mm dia or fixing with galvanised steel staples supplied and fixed complete to wood or steel members complete all as specified and directed by Engr-in-Charge.

Taking down steel rolling shutter and refixing with or with out ball bearing including to cover side guide rail and greasing of MS spring and side guide and make functional including complete overhaling size exc 10 sqm but nexc 40 sqm as entire satisfication of Engr-in-Charge. (Note : Supply of material to be measured seperately)

S&F of MS pipe medium grade of dia upto 40 mm including cutting and fixing, drilling, welding for rolling shutter all as directed by Engr-in-Charge.

S&F spring of high carbon spring 30mm dia drilling, welding for rolling shutter all as directed by Engri-in-Charge.

S&F in repair of mild steel rolling shutter strips made out of 1.25mm MS sheet including and reavting including one coat of primer and two coat of synthetic enmail paint all as directed Engr-in-Charge.

Dismantling of PVC pipes of any dia and discription from trenches or with walls etc complete all as specified.

S&F PVC pipes single socketed in any length with rubber ring joints fixed to wall (110mm bore) including flat iron claimp for proper fixing complete all as specified and as directed by Engineer-in-Charge.

S&F PVC pipes single socketed in any length with rubber ring joints fixed to wall (75mm bore) including flat iron claimp for proper fixing complete all as specified and as directed by Engineer-in-Charge.

S&F PVC bends 110mm dia complete all as specified by Engineer-in -Charge

S&F PVC bends 75mm dia complete all as specified and directed.

S&F in repair Rotational moulded Polyethylene (HDPE) Water Storage Tank 500 LITRE Capacity (Cylindrical Vertical with Closed Top), Black in Colour, Three Layered Construction, hoisted and fixed in Position all specified in MES Schedule Part-I, including tank nipple, union and Lowering of unserviceable water storage tank with float valve of any description complete all as specified and directed by Engineer in charge.

S&F in repair Rotational moulded Polyethylene (HDPE) Water Storage Tank 1000 LITRE Capacity (Cylindrical Vertical with Closed Top), Black in Colour, Three Layered Construction, hoisted and fixed in Position all specified in MES Schedule Part-I, including tank nipple, union and Lowering of unserviceable water storage tank with float valve of any description complete all as specified and directed by Engineer in charge.

S&F in repairs vitreous China squatting pan 'orrisa' pattern white colour of size 580x440mm with integral foot rests including provision of lime concrete including P traps complete all as specified and directed by Engr-in-Charge.

S&F in repair for vitreous china wash basin hand white flat backsize 600x480mm including cutting for and pinning in ends of brackets including fixing of 32 mm low dencity polylethyne pipes (LDPE)of pressure rating 6kg/cm2,cupling ,PVC connection with 15 mm dia PTMTcheknuts ,brackets all complete all as specified and as directed by Engineer-in-Charge.

S&F for steel water tubing 15mm bore, galvanised, medium grade with and including provision of all fittings of ISI marked and connected complete including taking down old GI pipe all as specified and as directed by Engineer-in-Charge.

S&F for steel water tubing 20mm bore, galvanised, medium grade with and including provision of all fittings of ISI marked and connected complete including taking down old GI pipe all as specified and as directed by Engineer-in-Charge.

Hacking out old broken glass (any thickness, size, quality or description) from wooden/steel /alluminium frame glazed with putty or fixed with wooden /almn beads etc.completed all as specified and as directed by Engr-in-Charge.

S&F4 mm thick sheet glass,ordinary quality,in squares n exc 0.50 sq m each pane fixed to aluminium frame with rubber gasket or fixed with glass putty as required etc completed all as specified and as directed by Engr-in-Charge.

S&F Single side writing informatory stainless steel reflecting Sign Boards size 4'x3' having with Aluminium sheet base of 2mm thickness having retro reflective tape base and front colour and matter of sign board will be furnished by Engr-in-Charge.The frame of Sign board shall be 2'' outer dia Square stainless steel pipe and having two legs of stainless steel Square pipe 9' long Each of 2'' outer dia square pipe the board shall be grouted in PCC work of size 350x350x450mm including taking down of existing complete all as specified and as directed.

Taking down Chowkhats or frames n exc 1.5 sqm each without taking of shutter from the frame all as specifed and directed by Engr-in-Charge.

Taking down shutter of any description exc 1 Sqm n exc 2 Sqm each complete all as specified and directed by Engr-in-Charge.

Taking down shutter of any description exc 2 Sqm each complete all as specified and directed by Engr-in-Charge.

S&F factory made 30mm thick solid core Flush door shutter with block board with BWP plywood on both side all as specified directed by Engr in Charge.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & as directed.

Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S Square tube, supplying & fixing in opening as per specification & drawing all as per specified and directed by Engr-in-Charge.

Preparation of new wooden surfaces of any description not otherwise described, over 10 cm width or girth and applying two coat of synthetic enamel paint over one coat of pink wood primer all as specified and directed by Engineer-in-Charge.

S&F butt hinges medium weight MS cold rolled 100mm long all as specified directed by Engr in Charge.

S&F 150 mm long aluminium anodised barrel tower bolt to extruded section and fixed all as specified directed by Engr in Charge.

S&F 150 mm aluminium handle, cast type anodised all as specified directed by Engr in Charge.

S&F 250 mm long aluminum alloy, anodised, sliding door bolt long whith hasp, staple (bolt type) and fixing clips of sheets, cast or extruded sections and fixidng bolts and siliding bolts of extruded sections or cast aluminium alloy and fixed all as specified directed by Engr in Charge.

M&L Gunitting work for RCC work as in columns, beam, slab, perapet, chajjas etc by removing all loose concrete on the reinforcement, cleaning the surfaces with wire brushes and reinforcement with sand papers than applying apoxy paint to rusted reinforcement and S&F welded wire mesh fabric size not less than 95x95x3 mm on the prepare surfaces and finally applying guniniting 30 to 40 mm thick (average thickness )with presure gun using 1 part of cement and 3 part of coarse cement incl necessary form work where ever required all gunnited surface shall be brought in complete geometric figure even in the guniting opration only complete all as specified and directed. Note:- Where new or additional reinforcement is required the same shall be paid for separetaly of this schedule as above.

M&L for 6 to 8 mm dia TMT bars, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with the including mild steel wire (annealed) not less than 0.9mm dia or securing with clips

All as per item No 81 here-in-before but in stirrups/binders complete all as specified and directed by Engr-in-Charge.

Supply and fix mild steel 1.25 mm thick rolling shutter without ball baring but gear operated with bevel gear box and crank handle including top cover anchor rod, hasp and staple including in two partirtation (as reqd ), including high carban steel spring, locking device and etc all as directed by Engr -in Charge

Note:- The amount of Rs 193500/- against Schedule of Credit on Page No 144 shall be deducted from the total amount quoted against Sch 'A' while deriving the Contract Sum for Acceptance

J.P. Enterprises (BID ID -3087183)

PAWAN KUMAR (BID ID -3087280)

M/S ujjwal associates (BID ID -3086365)

Phogat Builders (BID ID -3093040)

M/s Vijay Enterprises (BID ID -3075534)