Loading…
Loading…
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | 1₹15.8 LAccepted-Finance | ₹15.8 L | 1 | Accepted-Finance L1 |
| 2 | 2₹16.5 LAccepted-Finance | ₹16.5 L | 2 | Accepted-Finance L2 |
Updated dates
Tender Value
₹19.5 L
EMD Value
₹39,000
Closing Date
4 Feb 2026, 6:55 pmClosed
Executive Engineer MHD Baramulla
Executive Engineer, Mechanical and Hospital Division Baramulla
Design, Supply, Installation, Testing and Commissioning and allied works of Effluent Treatment Plant of 5KLD capacity based on MBBR technology at Sub District Hospital Charar-i-Sharief, Budgam.
2026_PWDJK_300514_1
MHDB/TS/2025-26/93
Open Tender
Machineries/ Mechanical Engg Items
30 days
M and H Sub-Division 2nd at Chara-i-Sharief
Please refer Tender documents.
9 documents required · 9 mandatory
₹1,000
Executive Engineer, MHD Baramulla
₹39,000
6 Feb 2026
13 Jan 2026
5 Feb 2026
13 Jan 2026
4 Feb 2026
13 Jan 2026
Design, Construction/Fabrication, Supply, Erection, Testing and commissioning of 5 KLD Effluent Treatment Plant (ETP) based on MBBR technology for SDH Uri as per technical specifications enclosed.
Design, Construction/Fabrication, Supply, Erection, Testing and commissioning of piping network of influent collection from various outlets of Hospital viz. Operation Theatre, Different Labs, Laundries Kitchen, Wards etc.to ETP Plant including drainage, PVC pipes of dia 4 Inch, Construction of Inspection Holes with Lids, pipe fittings with all other related works which are required etc. and also disposal network of treated water.
SITC of 25sqmm XLPE 3.5 core Al cable along with thumbing’s
SITC of three-phase oil immersed 10kva copper wound servo stabilizer wit following features: Copper wound Input 140-270 Output 230+-2% Efficiency better than 95% 24 hr continuous operation Microcontroller type, floor mounted, With high /low/surge and bypass features with robust mechanisms Ambient temp: -7 to +50 C
SITC of 100 A, 4 pole front operated COS enclosure type along with iron stand
Electrical fitting of ETP plant room, operator room and external premises
Lighting points consisting of 1.5sqmm copper wire, 20w flood lights, switches/MCB, pvc conduits
Heating points consisting of 2.5sqmm copper wire,16A socket with switches along with pvc conduits
SITC of 1200mm ceiling fan with dimmer along with 1.5sqmm copper wire and pvc conduits
3 pin socket points consisting of 1.5sqmm copper wire, switches pvc conduits
Structural steel work in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. Welded (SoR Item No 10.2.2)
Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting , hoisting , fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. Electric resistance or induction butt welded tubes (SoR10.16.3 )
Providing and fixing precoated galvanized iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self-drilling /self-tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. For Fabrication of Canopy over the Plant. (SoR 12.23)
Providing ridges or hips of width 60cm overall width plain G.S. sheets fixed with polymer coated J. or L hooks, bolts and nuts 8mm dia G.I. limpet and bitumen washers complete. 0.50 mm thick with zinc coating not less than 275 gram/m2 For Fabrication of Canopy over the Plant (SoR 12.4.3)
Earth work in bulk excavation by manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 m2 on plan) including disposal of excavated earth lead upto 50 meters and lift upto 1.5 m, as directed by Engineer-in-Charge. All kinds of soil : For Fabrication of Canopy over the Plant (SoR Item No 2.6.1)
Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centering and shuttering. All work upto plinth level with 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) For Fabrication of Canopy over the Plant (SoR Item No 4.4.5)
Please Enable Macros to View BoQ information
stage.html
html • 0.04 MB
tech_bid_open.pdf
tech_eval.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Tendernotice_1.pdf
PDF • 0.92 MB
NIT.pdf
Tender Documents • 1.47 MB
BOQ_974943.xls
BOQ • 0.28 MB
Download all tender documents and submit your bid