SPECIAL REPAIR TO CERTAIN OMQs AT SEKHON VIHAR UNDER

Amount

Schedule ‘A’ Part-I (B/R)

Dismantling of floor, hearth or wall tiling including cement morter bedding (but not backing), removing and rubbish off the premises.

Demolition of Cement Concrete (un-reinforced) of any description and in any positiin and removing the same from Site(s), complete all as specified and as directed.

M&L for 20 mm thick rendering in CM 1:4 by on brick/concrete surfaces of sunken slab, mixed with liquid water proofing compound both floor and wall of sunken slab, the surface shall be cured and allow to dry, finished even and smooth without using extra cement complete all as specified and as directed by Engineer-in-Charge. Note :- Water proofing compound shall be measured & paid separately.

Supply only liquid water proofing compound

M&L applying evenly two coat cemetious/liquid waterproofing coating on sunken slab/ceiling/wall as per manufacturer instructions including cleaning surface complete all as specified.

M&L for PCC 1:5:10 type E2 Using 40mm graded stone aggregate as in filling under floor/sunken slab.

M&L Cement Concrete type B1,1:2:4 (20mm Graded Stone Aggregate) 25 mm thick, as in Floors, etc., and finished the Cement Concrete Surfaces Even and fair without using Extra Cement, complete all as specified and as directed.

S & F vitrified tiles tiles light shade 10mm thick (square/rectangular) polished, area of each tile n.exc. 0.36 sqm, in floor etc.,set and jointed in neat cement slurry over 15mm thick screed bed in CM 1:6 and pointed in white or coloured cement with pigment to match for laying floor fineshes all as specified .

M&L for Ceramic coloured/ printed non-skid tiles of size 7-8 mm thick( square / rectangular ) area of each tile exceeding 0.06 Sqm but n. exec. 0.11 Sqm laid as in floors setting and jointed with neat cement slurry over & including 15 mm thick screed bedding layers of cement sand mortar ( 1:6) and pointed with coloured cement to match with surfaces of tiles complete all as specified and as directed.

M&L Glazed Ceramic Coloured Tiles, 200x300mmx7mm thick in size, set on Vertical Surfaces such as Skirting, Dado, etc,over and including 10mm thick screed bed in cement mortar 1:4 Set and Jointed in Neat Cement Slurry and Pointed in White or Coloured Cement to match the shade of the Tiles, complete all as specified and as directed.

M&L for 20mm thick pre polished granite (any colour) slab laid with 15 mm thick CM 1:6 bedding in door Chowkhat/Frame, Window Cill, plateform etc in floor and skirting/dado surface and jointed with grey cement slurry and pointed in white cement with pigment to match the shade of granite stone including Moulding/rounding and polishing all as specified and directed by Engr-in-charge

S&F Galvanised Steel Water Tubing 15mm Bore (dia), ‘Medium Grade’ with all Fittings, fixed on Walls, Ceiling or laid in Floors or any other Situ-ation including Taking up or down unserviceable Steel Water Tubing with Fittings and Connections, etc., complete all as specified and as directed.

S&F Centre hole Brass CP mixer for mixing hot & cold WHB Mixer 15mm Bore (dia) screwed down for iron pipe and fixed including taking down unserviceable WHB Mixer of any description, complete as all specified and directed.

S&F Wall Mixer for kitchen sink 15mm Bore (dia) brass chromium plated for mixing hot & cold, as Approved, fixing including Taking down unserviceable Wall Mixer of any description, complete as all specified and directed.

S&F Wall Mixer 15mm Bore (dia) brass chromium plated for mixing hot & cold, as Approved, fixing including Taking down unserviceable Wall Mixer of any description, complete as all specified and directed.

S&F Brass CP fancy type Bib Cock 15mm Bore (dia), Chromium Plated Long Body, screwed down, screwed for Iron Pipe or for Brass Ferrule and fixed-in-repairs, complete all as specified and as directed.

S&F Angle Stop Cock 15mm Bore (dia), fancy type,Chromium Plated, screwed down, screwed for Iron Pipe or for Brass Ferrule and fixed-in-repairs complete all as specified and as directed.

S&F Brass CP Health Faucet with 1.00m long tube and holder as Approved, including Taking down un serviceable Health Faucet of any description, complete as all specified and directed.

S&F Brass Chromium Plated Towel Rail 600mm Long and 20mm dia, as Approved, fixed including Taking down un serviceable Towel Rail of any description, complete as all specified and directed.

S&F stop valve CP 15mm bore(Concealed type), cast copper alloy, screwed down, high pressure with long shank or butterfly handle screwed both ends for iron pipe or union and fixed in repairs complete all as specified and as directed.

S&F in repairs Vitreous China White Wash down Water Closet Pan (Pedestal Pattern) including Bolts, (excluding Flushing Cistern and Flushing Pipe) including seat and seat cover, Making Good disturbed Surfaces with Cement Mortar 1:3, complete all as specified and as directed.

S & F in repairs Vitreous China Anglo Indian Pattern, size 580X440 mm White, with ‘P’ or ‘S’ Trap, Integral Foot Rest, including seat and seat cover, providing Joints between Flush Pipe and Socket of WC Pan excluding Flushing Cistern and Flush Pipe), complete all as specified and as directed.

S&F in repairs PVC Flushing Cistern 10 LITRE capacity, Low Level Valve Less, Symphonic Action type, White, with Inlet, Ball Valve, Float and Handle incl fixing PVC Flush Pipe of polythene 32mm dia complete all as specified and as directed.

S&F in repairs Vitreous China 550*400mm Size Oval Shaped Wash Hand Basin White with 32mm dia Brass Chromium Plated Waste Fitting, including Cutting Chase cutting in wall and Pinning in Ends, Making Good Disturbed Surfaces in Cement Mortar 1:3 and fixed including Taking down Unserviceable Wash Hand Basin and connected Items, complete all as specified and as directed.

S&F in repair 32 mm bore chromium plated bottle trap for wash hand basin with inlet & outlet screwed for iron pipes or connection including necessary packing , union and cap complete all as specified and as directed by Engineer-in-Charge.

S&F in repair, 6mm thick glass corner shelf (12"x12") with C type Brass CP bracket, complete all as specified and directed by Engr in charge.

S&F High pressure PVC connections pipe 600mm long suitable for Hot and Cold water for 15mm size with Brass CP Check nut complete all as specified and directed by Engr-in-Charge.

Dismantling of old existing PVC/CI/concrete pipes of any description, jointed in cement mortar up to 100 mm dia complete all as specified and directed.

S&F 110mm dia PVC SWR pipe laid to wall and floor and fixed with clamp complete all as specified and directed.

S&F 75mm dia PVC SWR pipe laid to wall and floor and fixed with clamp complete all as specified and directed.

S&F 32mm dia PVC SWR pipe laid to wall and floor and fixed with clamp

S&F in repair 32mm dia PVC SWR Bend

S&F in repair 100/75mm dia PVC SWR Bend

S&F in repair 110mm dia PVC SWR Bend

S&F in repair 110/75mm dia PVC SWR Junction Single (Tee)

M&L for replacement of 75mm outlet PVC(SWR) floor/nahani trap with steel grating including jointing and breaking/ dismantling any type of floor and making good cement concrete to the B-1 (1:2:4) and testing after repairs and taking down existing trap etc complete all as specified and directed by Engr-in-Charge

S&F in repair (HDPE) water storage LOFT Tank 200 Ltrs capacity in kitchen, hoisted and fixed in position all specified in MES Schedule Part-I, including tank nipple, union and lowering of unservicable Water Storage Tank including dismantling of old water tank complete all as specified and as directed by Engineer-in-Charge

S&F in repairs ball valve high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed 15 mm bore complete all as specified and directed by Engineer in charge.

M&L for 6mm thick Plywood 6mm thick, BWR Grade, type BB fixed with Screw including taking down old plywood of any description in the wall etc including two coat synthetic enamel paint over a coat of primer complete all as specified and as directed .

S&F in repairs aluminum door seal fixed to bottom of door shutters complete all as specified by engr in charge

S&F in repairs toilet paper holder of stainless steel fixed to wall with CP brass screws complete all as specified and as directed by the Engineer in Charge.

S&F sinks with drainage board made of stainless steel lmm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 1040 x 460mm bowl size 410mm x 330mm x 160mm

S&F in repair, Brass CP soap dish, complete all as specified and directed by Engr in charge.

S&F in repair stainless steel grating round /circular with waste hole or without waste hole of dia 75mm/ 100mm size of stainless steel complete all as specified and as directed by the Engineer in Charge.

S&F as in repair over head shower 150mm square size cast copper alloy, chromium plated, fancy type, with swivel joint with 250 mm long arm fixed to 15mm bore iron pipe complete all as specified and directed by Engineer-in-Charge

S&F in repair waste cupling fitting brass chromium plated of 32 mm dia for wash hand basin with long screwed sanks and fly nuts flange end bedded in red lead cement and other end fixed complete all as specified and directed by Engineer-in-Charge.

S&F in repair waste cupling fitting 75/100 mm size for 40/32 mm dia waste pipe for SS sink with long screwed shanks and fly nuts flange end bedded in red lead cement and other end fixed complete all as specified and directed by Engineer-in-Charge.

Taking down Cement Plaster from wall and ceiling of any description from Brick/concrete surfaces including raking out Joints, hacking for Key, scrubbing down with Water, etc., and removing same from the Site(s), complete all as specified and as directed.

M&L for 10 mm thick rendering in CM 1:3 on concrete/gunniting surfaces as in ceiling mixed with integral water proofing compound , the surface shall be cured and allow to dry, finished even and smooth without using extra cement complete all as specified and as directed by Engineer-in-Charge. Note :- Water proofing compound shall be measured & paid separately..

M&L for 15 mm thick rendering in CM 1:6 on brick/concrete surfaces of wall, mixed with integral water proofing compound, the surface shall be cured and allow to dry, finished even and smooth without using extra cement complete all as specified and as directed by Engineer-in-Charge. Note :- Water proofing compound shall be measured & paid separately.

M&L for preparation of newly plastered surfaces of walls by Vacuum based sanding machine complete all as specified, applying wall care putty min 3mm thick (multi purpose mixer shall be used for uniform and proper mixing of putty) and applying two coats oil emulsion distemper white or coloured by auto roller complete all as specified & directed by Engineer-in-Charge.

M&L for preparation of newly plastered surfaces of ceiling by Vacuum based sanding machine complete all as specified, applying wall care putty 3mm thick (multi purpose mixer shall be used for uniform and proper mixing of putty) and applying two coats oil emulsion distemper white or coloured by auto roller complete all as specified & directed by Engineer-in-Charge.

M&L for complete removal of plastered or un plastered old decorated surfaces of walls by Vacuum based sanding machine all as specified, removal of nails etc providing 3mm thick wall care putty (multi purpose mixer shall be used for uniform and proper mixing of putty) and applying two coat oil emulsion distemper white or coloured by auto roller complete all as specified & directed by Engineer-in-Charge.

M&L for complete removal of plastered or un plastered old decorated surfaces of ceiling by Vacuum based sanding machine all as specified,providing 3mm thick wall care putty and applying two coat oil emulsion distemper white or coloured by auto roller complete all as specified & directed by Engineer-in-Charge.

M&L for preparation of old painted surfaces of wood & wood based surface of any description not otherwise described over 10 cm width & girth and applying one coat of synthetic enamel paint complete all as specified and as directed by Engineer-in-Charge.

M&L for preparation of old painted surfaces of steel & steel based surface of any description not otherwise described over 10 cm width & girth and applying one coat of synthetic enamel paint complete all as specified and as directed by Engineer-in-Charge.

Taking down chowkhat or frames with shutters (without taking off shutters from the frame) n.exc. 1.5 Sqm each all as specified and as directed.

Ditto but exceeding 1.50 sqm each and n.exc. 4 Sqm each

Taking down shutters only n.exc. 1.00 Sqm each

Taking down shutters only exc 1 Sqm and n.exc. 2 Sqm each

S&F 25 mm thick factory made flush shutters, solid core construction, with particle board core and plywood face panels, commercial type on both the faces.

Do but 35 mm thick

M&L for 35 mm thick IInd class hard wood Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats→

S&F Anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified

Anodised aluminium window and ventilator shutters, side hung type or sliding without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) complete all as specified

S&F PVC door frame of size 50x47mm with a wall thickness of 5mm made out of extruded 5mm rigid prelaminated PVC foam sheet mite cut at two corners and jointing with 2 Nos of 150mm long brackets of 15x15mm MS square tube of two vertical door profiles are to be reinforced with 19x19mm MS square tube of 19 guage WPDM rubber gasket weather seal tobe provided throughout frame the door frame shal be fixed to the wall using 100mm long MS screws through the frame by using PVC fastners. A minimum of 04 Nos screws to be provided for each vertical members and minimum 02 Nos of horizontal members,

S&F for 30mm thick factory made solid panel prelaminated PVC door shutter consisting of frame made out of MS tube of 19 guage thickness and size of 19x19mm for styes and 15x15mm for topo and bottom rails. MS frame shall have a coat of steel primer of approved make and manufacturer. MS frame adhered with 5mm thick heat moulded PVC `L' channel of size 30x75mm forming styles and 5mm thick, 100mm wide PVC sheet for top rail lock rail and bottom rail on either side and 5mm thick 20mm wide PVC sheet as gap inserted for top rail and bottom rail. panelling of 5mm PVC sheet to be fitted in MS frame to the styles and rails with 5mm thick 30mm wide PVC sheet beading on either side and jointed together with solvent cement adhesive etc Complete all as specified and as directed by Engineer- in- Charge.

S&F in repair 18/19 mm thick prelaminated particle board exterior gde prelaminated one side with decorative choice and other side white lamination fixed with screws as in cup board shutters & shelves and pelmet boxes etc all as directed.

S&F 2nd class hard wood plain fillets not exc 3 sqcm sectional area, square, rectangular or tringular in section, wrought fixed with nails complete.

S&F in repairs 100 mm long,designer pattern Stanless Steel handles for fixing in cupboards all as directed and as specified by Engr-in Charge

S&F in repair, Magnet catch for fixing in cup board as approved by engr-in-Charge

S&F 75 mm long aluminium alloy butt hinges E-22 complete all as specified and as directed by Engr-in-Charge

Taking down old Aluminum windows of any description size not exc. 2.50 sqm and M&L for complete overhauling of the glass pane/rubber beeding/aluminum glazing clip if necessary/locking system incl.necessary roiling and adjustment etc and refixing in same location complete all asspecified and directed. Note :- Glass Pane/rubberbeeding/aluminum beeding will be measured and paid separately under subsequent items.

S & F in repair rubber beeding to be fixed over glass panes in Aluminum widows complete all as directed.

S&F in repair, aluminum anodised glazing clip to the alumiinum window frames after fixing the glass panes complete all as directed.

Dismantling structural steel work incl. steel door,gate,window guard bars,grills etc.

M&L fabricated frame work as in doors of gate of angle iron or other section with gusset plate rails, braces etc. complete drilled for fixing steel sheeting or other covering door etc to be prepared for hanging with and including hinges .

M&L for mild steel works as in grills and railing of Fe-410-0or Fe 310-0, complete all as specified and as directed by Engr-in-charge

M&L PCC for 1:2:4 type B-1 (using 20mm graded stone aggregate) as in coping, benching & for fixing railing, holdfast etc complete.

Hacking out old broken glass (any th size, quality or description) from wooden or steel frames glazed with putty or fixed with wooden beads complete all as directed.

S&F Figured Glass pin head type 4.0mm thick, fixing to Aluminium Sections as in Panel of Doors, Windows Shutters and Panelling Works with necessary fixing Arrangements viz Jointing Cleats, Glazing Clips, Rubber Packing, Screws, etc., as required/ordered at Site(s), complete and fixed repairs all as specified and as directed.

S&F Sheet Glass ordinary 4.0mm thick, fixing to Aluminium Sections as in Panel of Doors, Windows Shutters and Panelling Works with necessary fixing Arrangements viz Jointing Cleats, Glazing Clips, Rubber Packing, Screws, etc., as required/ordered at Site(s), complete and fixed repairs all as specified and as directed.

S&F in repair for Stainless steel wire cloth 0.36 mm nominal dia of wire and average width of apoerture 1.40mm and fixed with aluminium/wooden/steel beads complete.

S&F MS medium weight cold rolled butt hinge ISI Marked 100mm size, fixed with screw complete all as specified and as directed.

S&F in repairs, MS Helical door spring 300 mm long complete all as specified and as directed by Engr in Charge(Note:-Helical spring will be fixed by welding)

S&F butt hinge extruded aiuminium alloy with galvanised mild steel hinge pin 100mm size, fixed with screw complete all as specified and as directed.

S&F extruded anodised aluminum alloy handle 150mm long fabricated type

S&F anodised aluminum barrel tower bolt of extruded section 150mm long

S&F aluminum alloy sliding door bolt 300mm long with hasp, staple (bolt type) adnd fixing clips of sheets, cast of exctruded sections and fiing bolts or extruded section and all as specified

S&F telescopic drawer channel 18" long complete all as specified and directed by Engr in charge

S & F in repair floor door stopper of size 140 mm long aluminium alloy body and tongue, anodized with hard drawn steel spring incl cleats etc fixed to door.

S&F in repairs 25mm dia stainless steel curtain rods including cutting and fixing complete all as specified and as directed by Engr-in-Charge

S& F in repairs Stainless Steel wall bracket suitable for 25mm dia curtain rods complete all as specified and as directed by Engr in Charge

S& F in repairs Stainless Steel designer pattern side knobs suitable for 25mm dia curtain rods complete all as specified and as directed by Engr in Charge

M&L preparation of new or previously untreated surfaces of wood of any description not otherwise described width or girth and applying two coats of synthetic enamel paint over & incl one coat of pink primer complete all as specified.

M&L preparation of new or previously steel surfaces of any description not otherwise described width or girth and applying two coats of synthetic enamel paint over & incl one coat of red oxide primer complete all as specified.

S&F contineous (piano) hinges, mild steel bright finish of 40 mm width of flaps(when open) complete all as specified.

Removal of debris/malwa to a distance exc 10 Km but n exc 15.00 Km out side MD land as per NGT norms and filling in low lying area complete all as specified and as directed by Engr in Charge.

Demolition of reinforced cement Concrete of any description and in any position not otherwise specifically provided for complete all as specified and as directed by Engr in Charge

M&L Reinforced cement concrete (design mix)M-25 (20 mm graded agg )in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and as directed by Engr in Charge

M&L Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) complete all as specified and as directed by Engr in Charge

M&L Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed by Engr in Charge

M&L Rebaring of mild steel bars upto 150 mm depth incl fixing complete all as specified and as directed by Engr in Charge complete

Schedule ‘A’ Part-II (E/M)

Taking down copper/aluminium point wiring (light points) complete, including fixtures and fittings such as switches, ceiling roses, pendents, regulators, sockets, light fittings etc. removing materials to store for keeping in safe custody or for taking credit (credit for the above items should be made as per conditions seperately) and making good disturbed surfaces of walls. floors, etc. complete all as directed

Taking down copper/aluminium submain wiring single core 4 sqmm 3 wire complete, including conduits of any kind, and removing materials to store for keeping in safe custody or for taking credit (credit for the above items should be made as per conditions seperately) and making good disturbed surfaces of walls. floors, etc. complete all as directed

Taking down copper/aluminium submain wiring 6 sqmm 6 wire complete, including conduits of any kind, and removing materials to store for keeping in safe custody or for taking credit (credit for the above items should be made as per conditions seperately) and making good disturbed surfaces of walls. floors, etc. complete all as directed

Taking down main switches, distribution boards etc of any type and capacity along with the existing boards, and removing the same from site and making good the disturbed surfaces/portion of walls etc. all as directed.

Taking down of serviceable ceiling fans/wall mounted fan and refixing the same on same position including cleaning and painting after the work is over.

Taking down of serviceable Exhaust fan/Ventilating fans and refixing the same on same position including cleaning and painting if reqd after the work is over.

Taking down water heater storage type electric capacity 25 liters and refixing the same after repair of the bldg on same location including cleaning of the geyser body complete.

M & L for point wiring (concealed on wall & surface/concealed on cealing) for one light/fan/exhaust fan controlled by one modular/piano switch one way in different locations/building including rigid non metallic PVC conduit, medium grade, ISI marked , 20 mm dia, with 1.5 sqmm FRLS PVC insulated & sheathed cable , stranded copper conductor of 1.5 sqmm as continuous earth connected to common earth dolly, complete all as specified and directed by Engr-in-charge.

All as per item No 114 above but for 5 Amps 5 Pin socket outlet on the same board

All as per item No 114 above but for 5 Amps 5 Pin socket outlet on independent board

All as per item No 114 above but One bell/buzzer point controlled by on bell push

All as per item No 114 above but One light point controlled by two 2- way switches with cables 1.5 sqmm size copper wire.

All as per item No 114 above but one 5 pin, 15 Amp socket outlet on independent board for power point with 2.5 sqmm size copper wire

S& F ceiling rose, 2 to 3 terminals complete all as specified and as directed .

S&F Modular switch, one way 6 Amps , 1 module as specified.

S&F Modular Socket , 6 A-2/3 Pin combined 2 module all as specified and directed.

S&F in replacement of switch modular one module 2 way 6Amps complete all as specified and directed.

S&F twin socket modular type heavyduty out let 6 pin 6/16 Amps 2 module,

S&F switch Modular type 16 Amps , single pole one way 240 volts one module as specified.

S&F Modular Fan step Regulator Bell ,120 W-2 module as specified.

M&L for metal flush box for fixing of switches for 1/2 module

M&L for metal flush box for fixing of switches for 3 module

M&L for metal flush box for fixing of switches for 4 module

M&L for metal flush box for fixing of switches for 6 module

M&L for metal flush box for fixing of switches for 8 module

Supply & fix Modular White cover plate with frame for 1/2 module

Supply & fix Modular White cover plate with frame for 3 module

Supply & fix Modular White cover plate with frame for 4 module

Supply & fix Modular White cover plate with frame for 6 module

Supply & fix Modular White cover plate with frame for 8 module

S&F Modular type blank plate , 1 module as specified.

Supply & fix sheet metal enclosure for 220 volts 20 Amps with a three pin and earth plug top with socket and one single pole MCB 20 amps complete as well as specified and directed.

Supply and fixing 240V, 10 KA 'B' curve miniature circuit breaker (MCB) of single poles and current carrying capacity 32 AMP, in the MCB DB Complete with connection testing and commissioning complete all as specified and as directed.

S&F Sheet metal enclosure DD SPN 240 Volts 04 way DB with 200 Amps rated busbar complete all as specified and directed.

S&F TPN DB 415 Volts 8 way double door type DB complete all as specified and directed.

S & F MCB SP of rating, 06 to 32 Amp,240 volt, 10 KA 'B' Series type complete all as specified and as directed.

S & F MCB TPN 63 Amps 415V 10KA 'B' curve miniature circuit breaker current carrying capacity in the DB complete with connection testing and ommissioning complete all as specified and as directed.

M&L for concealed sub main wiring Six run of 06 sqmm PVC insulated unsheathed copper conductor cable ISI marked 1100 volts grade drawn in and including PVC surface conduit suitable size of medium grade fixed on wall/ceiling/passing through wall etc connected as required at site complete all as directed. Note- (a) Four runs of single core cable with two run of earth continuity cable including PVC conduit and its accessories will be measured and paid as one unit). (b) Make disturbed surface good to wall/floors as existing surface.

M&L for concealed sub main wiring three run of 04 sqmm PVC insulated unsheathed copper conductor cable ISI marked 1100 volts grade drawn in and including PVC surface conduit suitable size of medium grade fixed on wall/ceiling/passing through wall etc connected as required at site complete all as directed. (For AC connection ) Note- (a) Two runs of single core cable with one run of earth continuity cable including PVC conduit and its accessories will be measured and paid as one unit). (b) Make disturbed surface good to wall/floors as existing surface.

M&L for inverter wiring with FRLS PVC insulated cable 2.5 Sqmm copper conductor solid core unsheathed cable in existing conduit complete

S & F RCCB Double pole, 100mA of rating, 40 Amp,240 volt, 100 mA complete all as specified and as directed.

S&F Modular switch, one way 6 Amps Bell push, 1 module as specified.

S&F Bell, AC, 230 volts, single pole as specified.

Schedule of Credit

M/S Parshant Associates

M/S Rohit Enterprises

M/S mk enterprises

POOJA ENTERPRISES

Green Leaves

Chankaya Solutions