MISC B/R REPAIR TO CERTAIN BLDGS IN MD ACCN INCLUDING INTERNAL ELECTRIFICATION AT AF STN ADAMPUR

Amount

BR WORKS

PCC type E-2 (1:5:10), using 40 mm graded crushed stone aggregates as in filling & mass concrete, complete all as specified and directed

Reinforced cement concrete, type B-1, (1:2:4), using 20 mm graded crushed stone aggregates as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, and in shelves and the like complete all as specified and directed.

Brick work using bricks as specified in PS clause 5.1, straight or curved on plan exceeding 6.00 metre mean radius built in cement mortar (1:6), complete all as specified and directed.

Brick work in half brick thick wall using bricks as specified in PS clause 5.1, straight or curved on plan exceeding 6.00 metre mean radius built in cement mortar (1:4), complete all as specified and directed.

Use & waste of formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200 mm thick (Horizontal or sloping) with fair finished flat surfaces of concrete, complete all as specified and directed.

Factory made, 30 mm thick, first class hard wood, plain framed, hammer marked, skelton shutter (two panel to receive wire gauge) with lock rail . The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified and directed

Factory made, 30 mm thick, second class hard wood, plain framed, hammer marked, skelton shutter (two panel to receive wire gauge) with lock rail . The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified and directed

Factory made, 30 mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides,ISI marked, complete all as specified and directed.

Factory made, 35 mm thick flush shutters, solid core construction, with block board core and plywood face panels, with 0.9mm decorative laminate type 1 of surface finish, colour and pattern as approved by GE and fixed with approved adhesive on both sides, ISI marked, complete all as specified and directed.

Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails, MS frame shall be covered with heat moulded wood grain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for styles and wood grain colour PVC sheet for top rail, lock rail and bottom rail, panelling of wood grain colour PVC sheet to be fitted in the MS frame welded / sealed to the stile and rails with suitable PVC sheet beading and jointed together with solvent cement as specified in SSR Part II, complete all all as specified and directed.

Factory made solid PVC Door frame of size 50mm x 47mm made out of 5mm thick wood grain colour PVC sheet reinforced with mild steel square tube, suppling & fixing in opening, complete all as specified and directed.

Plywood 6 mm thick, 5 ply type BB commercial BWR one side laminate confirming to IS: 303 fixed on frame, IN REPAIRS, complete all as shown and directed.

Plywood 12 mm thick, 7 ply type BB commercial BWR one side laminate confirming to IS: 303 fixed on frame, IN REPAIRS, complete all as shown and directed.

Plywood 18 mm thick, 12 ply type BB commercial BWR one side laminate confirming to IS: 303 fixed on frame, IN REPAIRS, complete all as shown and directed.

Factory made uPVC door frame made of uPVC. extruded sections having an overall dimension (extruded section profile) 48x40 mm (tolerance ± 1 mm), with wall thickness 2.0 mm (± 0.2 mm), corners of the door frame Jointed with galvanized brackets and stainless steel screws, joints mitred and Plastic welded. The hinge side vertical of the frames reinforced by galvanized M.S. tube of size19 X 19 mm and 1mm (± 0.1 mm) wall thickness and 3 nos. stainless steel hinges fixed to the frame complete all as specified and directed.

Factory made uPVC white colour Three track three panels sliding window with fly proof S.S wire mesh (Two nos. glazed & one no. wire mesh panels) made of (big series) frame 116 x 45 mm & sash 46 x 62 mm both having wall thickness of 2.3±0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of window above 1.75 sqm) comprising of uPVC multi chambered frame, with inbuilt roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. complete all as specified and directed..

Factory made uPVC white colour casement door with 3D hinges made of (big series) frame 67 x 64 mm & sash 67 x 110 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of door upto 2.00 sqm) comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, zinc alloy (white powder coated) 3D hinges and one handle on each side of panels along with zinc plated mild steel multi point locking having transmission gear, cylinder with keeps and one side key, G.I. fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws,etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality complete all as specified and directed. NOTE: The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories.

NOTES APPLICABLE TO SERIAL ITEM 16 TO 21: - (i) After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality. (ii) Glass or wiremesh shall be paid separately) (iii) For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.

Aluminium anodised barrel tower bolt of extruded section 150 mm long, ISI marked, complete all as specified and directed.

Aluminium alloy, anodised, ISI marked sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloy 250 mm long, complete all as specified and directed.

Stainless steel 100mm long butt hinges with stainless steel screws, ISI marked complete all as specified and directed. MAKE: PRAYAG CAT HG-3414 or equivalent make mentioned in Appendix 'B'

Mild steel ordinary rat tail rod pattern helical door spring 250 mm long including roller and roller plate, complete all as specified and directed.

Extruded aluminium anodised handles 125 mm long fabricated type with plate , ISI marked complete all as specified and directed.

Stainless steel conduit 20 mm bore, cut to size and erected in position as curtain rod on backets, with & including SS decorative finials & brackets, PVC rings @ 10 nos. per metre, fixed to walls with PVC rawl plugs & SS screws, IN REPAIRS, complete all as specified and directed.

Double leg aluminium anodised door stopper with rubber foot, ISI marked and fixed to bottom rail of doors with steel screws, complete all as specified and directed.

Stainless steel 100mm size auto soft closing hydraulic hinges fixed with stainless steel screws, ISI marked complete all as specified and directed.

Stailess steel, handle, 125 mm long, curve shapewith stainless steel screws, complete all as specified and directed. MAKE: PRAYAG CAT NO. DHC-2125 or equivalent make mentioned in Appndix 'B'

Mild steel chromium plated solid handle, 100mm suitable for cupboard shutter, complete all as specified and directed.

Stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperature 1.40 mm and fixed with tinned tacks or steel wire staples, complete all as specified and directed

Stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperature 1.40 mm and fixed with tinned tacks or steel wire staples IN REPLACEMENT, complete all as specified and directed.

Framed mild steel work such as grills, grating etc. with ends of bars shouldered and or riveted or forged into spikes, framed guard bars, railings and similar work confirming to Fe-290-Gde E-165, complete all as specified and directed.

Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

Mild steel work as in joist, channel, angle, or tee sections, fixed independently, without connecting plates, etc. (cut to ordinary lengths i.e. within 20mm of the length indicated) quality confirming to grade Fe-290-Gde E-165, complete all as specified and directed.

Rolled mild steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161-1979 grade St.-240, complete all as specified and directed.

Factory made pre painted pressed steel frames, conforming to IS, having profile 105 mm x 60 mm for doors with one or more rebates made out of 1.25 mm thick mild steel sheet, including necessary fixing lugs, butt hinges, lock strike plate, etc., duly filled with PCC(1:3:6) type C-0 complete, complete all as specified and directed.

Factory made pre painted pressed steel frames, conforming to IS, having profile 125 mm x 60 mm for doors with one or more rebates made out of 1.25 mm thick mild steel sheet, including necessary fixing lugs, butt hinges, lock strike plate, etc., duly filled with PCC(1:3:6) type C-0 complete all as specified and directed.

Factory made steel windows with side hung shutter with glazng bars each shutter having 02 No. box type hinges & two nos. tower bolts of size not less than 150 mm size and peg stays, dovetailed or welded,complete.

Factory made steel windows with side hung shutter without glazng bars each shutter having 02 No. box type hinges & two nos. tower bolts of size not less than 150 mm size and peg stays, dovetailed or welded,complete.

Steel windows or ventilators, fixed type made of MS sheet 1.25 mm thick box type (primer coated), ERW hollow 'P' section of size 60mm x 25 mm complete all as specified and directed. NOTES APPLICABLE TO SERIAL ITEM NO. 41 TO 43: (a) Profile section used under these items shall be 'P' tube as shown in drawing No. CE/AF/STD-170/07, CE/AF/STD-171/07 and CE/AF/STD-172/07 as applicable.

WPC(wood Polymer Composite) Louver 23 mm thick for indoor 3d wall pannelling, colour and pattern as approved by GE complete all as specified and directed

Aluminium frame for doors, windows, ventilators or in wall cladding with one or more rebates including joining cleat for fixing etc. complete all as specified and directed.

Powder coated aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and directed.

Powder coated aluminium door shutters with styles & rails made out of section size 83-85 mm x 44-45 mm (wall thickness not less than 2 mm) , anodised alumnium glazing snap beading (having wall thickness not less than 0.90 mm), rubber neoprene packing including joining cleats & screws etc as per manufacturers instructions, complete all as specified and directed. NOTES: (a) Each shutter shall have 2 Nos. 200 mm long almn handles and 03 No. 100 mm size stainless steel/almn butt hinges. (b) Glass and other filling materials in panels including wire cloth and almn grill shall be measured & paid for separately under respective item of BoQ. (c) For powder coated aluminum sections minimum thickness of powder coating shall be 50 micron.

Powder coated aluminium window and ventilator shutters side hung type with styles & rails made out of section size 47-48 mm x 44-45 mm (wall thickness not less than 1.58 mm), anodised alumnium glazing snap beading (having wall thickness not less than 0.90 mm), rubber neoprene packing including joining cleats & screws etc as per manufacturers instructions, complete all as specified and directed. NOTES: (a) Each shutter shall have 2 Nos. 125 mm long almn handles and 02 No. 75 mm size stainless steel/almn butt hinges & one no. almn hook & eye. (b) Glass and other filling materials in panels including wire cloth and almn grill shall be measured & paid for separately under respective item of BoQ. (c) For powder coated aluminum sections minimum thickness of powder coating shall be 50 micron.

Powder coated aluminium grill type DG-117 including necessary 'U' clip & screws etc as per manufacturers instructions, complete all as specified.

Aluminium composite panel sheet 3-4 mm thick, of shade approved by GE, cut to shape and fixed in position on frame work as in wall, complete all as specified.

Powder coated (minimum thickness of coating 50 micron) aluminium three track sliding window using series 'C' sections series of make JINDAL or equivalent and frame having three shutters - two glazed (with & including 5.5 mm thick tinted glass) & one gauged (with stainless steel wire cloth) including acessories like almn snap beading, jointing cleats, glazing clips, rubber packing rollers etc. complete comprising the following: - (a) All round frame using rectangular section size 100 x 20 x 1.4 mm. (b) Frame bottom - Jindal Cat 20704 or equivalent size. (c) Frame top & sides - Jindal Cat 20696 or equivalent size. (d) Shutter top & bottom - Jindal Cat 20529 or equivalent size (e) Shutter sides - Jindal Cat 20529/20530/20531 or equivalent size.

Gl frame work for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/ intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre, complete all as specified.

Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs / trusses by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified and directed.

Seamless calcium silicate ceiling 8mm thick made out of 1800 x 1200 mm size board of siliceous and calcareous material reinforced with cellulose fibre fixed to the ceiling section with 25 mm long self drilling and tapping screws having phillips head with under head cutter at 200 mm centre to centre, including finshing the joint of face board with specially formulated jointing compound and 48 mm wide fibre tape to provide seam less finish, complete all as specified. NOTE: Frame work & hangers for ceiling shall be measured and paid separately)

Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm of any colour hving tensile strength of 550 Mpa as in roof coverng/ cladding to wall, fixed with self tapping screws complete all as specified and directed.

Water Proofing Treatment to RCC roofs comprising of : -

Taking down existing water proofing treatment (any no. of layers) from RCC roofs including cleaning the surface including flashings and junction of parapet etc. with wire brushing & water to the entire satisfaction of EIC, complete all as specified and directed.

PCC (1:2:4) type B-1 using 20 mm graded stone crushed aggregate, laid to slope as directed by Engineer in Charge over RCC roofs as padding, complete all as specified and directed.

Rendering 15 mm thick (Average thickness) rendering on roof surface including flashings and junction of parapets etc., finished even and fair in cement mortar (1:4), using water proofing compound as recommended by manufacturers after brushing cement slurry @ 1.20 kg/Sq. m, complete all as specified and directed. NOTE: Supply only WPC will be measured & paid for separately under respective item of BoQ.

APP based polymeric membrane laid on primed roofs & flashing by forced application using Butane torch and sealing all joints on primed surface by applying hot blown industrial grade bitumen @ 85/25 @ 1.20 kg/Sq.m over a coat of bitumenous primer @ 0.40 litre per square metre over clean RCC/plastered roof surfaces & flashings complete all as specified and directed.

40 mm thick brick tiles (EXCEPT TILES) bedded over 15 mm thick cement mortar (1:4), and joints grouted flush in cement mortar (1:3) mixed with 5% of crude oil by weight of cement on APP membrane complete all as specified and directed.

40 mm thick brick tiles bedded over 15 mm thick cement mortar (1:4), and joints grouted flush in cement mortar (1:3) mixed with 5% of crude oil by weight of cement on APP membrane complete all as specified and directed.

Making benching with PCC (1:2:4) type B-0 (using water proofing compound) along side walls adjoining to roofs, in CONCAVE SHAPE, complete all as specified and directed. NOTES: (i)WPC will be measured and paid for separately under respective item of BoQ. (ii) For Performance Guarantee of Water Proofing Treatment refer PS clause 11.5.

Supply only water proofing compound (WPC), ISI marked, complete all as specified.

Water Proofing Treatment to RCC sunken surfaces comprising of : -

Rendering 15 mm thick (Average thickness) rendering on sunken surfaes including flashings, finished even and fair in cement mortar (1:4), using water proofing compound as per recommended ratio, after brushing cement slurry @ 1.20 kg/Sq. m, complete all as specified and directed. NOTE: Supply only WPC will be measured & paid for separately under respective item of BoQ.

LDPE sheet 150 micron laid over applying evenly a tack coat of industrial bitumen 85/25 at the rate of 1.2 kg per sq. m & adjoining vertical surfaces including applying bitumenous primer @ 0.40 litre per square metre over clean RCC/plastered roof surfaces complete all as specified and directed.

18/19 mm thick high density moisture resistant (HDMR) board, flat pressed, fixed as in modular kitchen cabinets, cupboards, shelfs or similar works with necessary screws complete all as specified and directed.

Decorative laminates type I, 0.9-1 mm thick of surface finish, colour and pattern as approved , fixed with approved adhesive complete all as specified and directed.

High quality solid colour (matching shade) PVC edge banding tape not less the 3 mm thick having 18/19 mm width fixed with approved adhesive to HDMR board complete all as specified and directed.

Ball bearing runners 45mm telescopic channel (20 inch) full extension load capacity 50 kgs complete all as specified and directed.

Chrome plated stainless steel wire basket (storage basket) pull out type for large utensills, size 486x500mm with necessary fixing clips etc.complete in all respect complete all as specified and directed

Chrome plated stainless steel wire basket (cup and soucer basket) pull out type, size 530x500mm with necessary fixing clips etc. complete all as specified and directed

Chrome plated stainless steel wire basket (jar basket) pull out type, size 536x500mm with necessary fixing clips etc. complete all as specified and directed.

Chrome plated stainless steel wire basket (Thali basket) pull out type,size 380x500 mm with necessary fixing clips etc. complete all as specified and directed

Chrome plated stainless steel wire basket pull(cutlery basket) out type,size 380x500 mm with necessary fixing clips etc. complete all as specified and directed

Chrome plated stainless steel wire basket pull (storage/plain basket) out type,size 380x500 mm with necessary s fixing clips etc. complete all as specified and directed

Chrome plated stainless steel wire basket pull (Bottle pull out) out type,size 150 to 200 mm with necessary sliding frame structure, fixing clips etc. complete in all respect as specified

25 mm thick, cement concrete type B-0, 1:2:4 using 12.5 mm graded crushed stone aggregate, finished even & rough, as in sub floors, complete all as specified and directed.

75 mm thick, cement concrete type C-1, 1:3:6 using 20 mm graded stone aggregate, finished even & smooth without using extra cement, as in plinth protection, and joints shall be sealed with joint sealing comound grade 'A' complete all as specified and directed.

100 mm thick, cement concrete type D-2, 1:4:8 using 40 mm graded stone aggregate, finished even & rough, as in sub floors, complete all as specified and directed.

Granite jet black shade, 15-18 mm thick,as in step, jambs, cooking platform and like, machine cut, machine polished, bedded and jointed with grey cement slurry & pointed with grout of matching shade including necessary cutting over & including 10 mm thick (average thickness) cement mortar (1:4), complete all as specified and directed.

Rounding of / moulding to edges (half round) of stone of any description including rubbing and polishing (Granite finish), complete all as specified.

UV marble sheet 2-3 mm thick, colour and pattern as approved by GE fixed with approved adhesive as per manufacturer instructions etc complete all as specified and directed

Glazed ceramic coloured tiles 7mm thick, area of each tile exc. 0.17 Sq.m but n. exc. 0.19 Sq.m on vertical surfaces as in skirting, dado etc. set and jointed in neat cement slurry and pointed with grout of matching shade of tiles, laid over and including 10 mm thick bedding layer in cement mortar (1:4), complete all as specified and directed.

First quality, vitrified ceramic tiles 9-10mm thick (square/ rectangular) area of each tile exc. 0.42 Sq.m but n. exc. 1 Sq.m, laid in floors etc, set and jointed in neat cement slurry and pointed with grout of matching shade of tiles, laid over and including 15 mm thick bedding layer in cement mortar (1:4), complete all as specified and directed.

First quality, vitrified ceramic tiles 9-10mm thick (square/ rectangular) area of each tile exc. 0.42 Sq.m but n. exc. 1 Sq.m, on vertical surfaces as in skirting, dado etc. set and jointed in neat cement slurry and pointed with grout of matching shade of tiles, laid over and including 10 mm thick bedding layer in cement mortar (1:4), complete all as specified and directed.

Non skid ceramic coloured tiles 7 to 8mm thick (square/ rectangular) area of each tile exc. 0.11 Sq.m but n. exc. 0.18 Sq.m, laid in floors etc, set and jointed in neat cement slurry and pointed with grout of matching shade of tiles, laid over and including 15 mm thick bedding layer in cement mortar (1:4), complete all as specified and directed.

60 mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of shape approved by GE, made by table vibratory method using PU mould, laid in required pattern over and including 50mm thick compacted bed of coarse sand, compacting through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified and directed.

Cleaning the surface and made free of dirt, foreign particles, laitance followed by grinding all protrusions to make surface modulated. Thereafter, inspection for cracks on the surface caused by thermal expantion contraction. Cutting the grooves with suitable cutter machine in "v" groove filled with Repair mortar/Microconcrete/General purpose grout as recommended proportionaly as per recommendation of manufacturer.Making of Gollas at all the corners with Polymer modified mortar(1:4 Cement:sand with 3.5% Acylic of cement weigth) and " Supplying and applying High build elastomeric waterproofing coating based on pure, hydrophobic polyurethane, cold applied of spray / brush applied, membrane with an elongation of 280% and tensile strength of 2.7 N/mm2 as per ASTM D 2370, crack bridging ability of 3mm, no leakage upto 5 bars of water pressure as per DIN 1048, min 88 % solid content. The system includes final base preparation, epoxy primer 1:1(Resin:hardner) application with 100 % water dilution and Pure polyurethane application in 2 coats with a total min consumption of 1.25 Kg per SQM and glass fibre mesh of 2.5mmx2.5mm needs to be sandwiched b/w two coats complete all as specified and directed. NOTE: Application should be done with Graco sprayer by a company authorised applicator.

Repairing of RCC projection chhajjas, roof, facia etc by necessary preparation. Scraping cutting, chiseling derusting and cleaning exposed reinforcement, surfaces of damaged, loose RCC with cement concrete Type A-0 (1:1.5:3) and reinforcement with chicken mesh of weight not more than n.exc 3 kg/Sq.m (if reqd) with or without facia and finished with cement and sand mortar (1:3) using coarse sand and work in patches of area n.exc 5 Sq.m and thickness of RCC member n.exc 70 mm incl necessary formwork at any height/location complete all as specified and directed. NOTE: The rate quoted by the contractor shall included for chicken mesh, scaffolding and necessary formwork upto triple storey bldg.

Rendering 5 mm thick on fair faces of concrete surfaces, finished even and smooth on ceiling in cement mortar (1:3), complete all as specified and directed.

Rendering 15 mm thick on fair faces of brick work or concrete surfaces, finished even and fair on walls in cement mortar (1:6) complete all as specified and directed.

Rendering 15 mm thick on fair faces of brick work or concrete surfaces, finished even and fair on walls in cement mortar (1:4), mixed with water proofing compound as per manufacturers instructions, complete all as specified and directed. NOTE: WPC will be measured and paid for separately under respective item of BoQ.

One coat of white washing on old decorated ceiling surfaces, including preparation of surfaces, complete all as specified and directed.

Three coats of white washing on new undecorated ceiling surfaces, including preparation of surfaces, complete all as specified and directed.

Prepration of new plasterd wall surfaces of any description complete all as specified and applying the following: - (a) Applying wall care putty, in two coats & smoothening the surfaces as specified. (preparatory to paint as directed). (b) Two coats of interior acrylic distemper/oil bound distemper over and including a coat of interior primer.

Complete removal of existing treatment of any description, including prepration of wall surfaces of any description complete all as specified and applying the following: - (a) Applying wall care putty, in two coats & smoothening the surfaces etc. as specified (preparatory to paint as directed). (b) Two coats of interior acrylic distemper/oil bound distemper over and including a coat of interior primer.

Prepration of new plasterd wall surfaces of any description complete all as specified and applying the following: - a) Applying wall care putty, in two coats & smoothening the surfaces as specified. (preparatory to paint as directed).complete all as specified. (b) Two coats of exterior acrylic emulson over and including a coat of water based exterior primer complete all as specified.

Complete removal of existing treatment of any description, including prepration of wall surfaces of any description complete all as specified and applying the following: - (a) Applying wall care putty, in two coats & smoothening the surfaces etc. as specified (preparatory to paint as directed). (b) Two coats of exterior acrylic emulsion over and including a coat of water based exterior primer.

Sheet glass 4 mm thick ordinary quality and glazing with oil putty or wooden beads in squares n. exc. 0.5sqm in each pane complete all as specified and directed.

Figured glass 4mm thick ordinary quality and glazing with oil putty in squares n. exc. 0.5 Sq.m in each pane complete all as specified and directed.

Plain tinted sheet glass, 5-6 mm thick, ordinary quality duly sticked with solar control reflective type film, having thickness not less than 25 micron and fixed air tight with neoprene packing & almn glazing clips, for aluminium/uPVC sections, complete all as specified and directed. NOTE: Almn glazing clips & neoprene packing will be measured & paid for under respective item of aluminium door/windows/partition.

8mm thick clear toughened glass with clear visibiity and fixed in aluminium/uPVC frame with necessary fixing material as approved by GE glazing with putty or fixed with beads complete all as specified and directed. .

10 mm thick Toughned glass as in hinged doors, partitions automatic doors (area of one shutter not exc. 1.50 Sqm) and similar work including cutting to shape, drilling holes required , Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and 300mm stainless steel handle (2 handle on each leaf) , complete all as specified and directed

One coat (finishing coat) of synthetic enamel paint over wood and wood based surfaces of any description not other wise described over 10cm width or girth, including preparation of surfaces, complete all as specified.

Two coats of synthetic enamel paint over & including a coat of pink primer over wood and wood based surfaces of any description not other wise described over 10cm width or girth including preparation of surfaces, complete all as specified and directed.

One coat (finishing coat) of synthetic enamel paint over old painted steel or iron surfaces of any description not other wise described over 10cm width or girth including preparation of surfaces, complete all as specified and directed.

Two coats of synthetic enamel paint over & including a coat of red oxide primer over steel or iron surfaces of any description not other wise described over 10cm width or girth including preparation of surfaces, complete all as specified and directed.

Preparation of wooden surface including cleaning with sand paper and applying two coats of french polish to achieve glossy finish and including minor fillings with putty as required complete all as specified and directed.

Disconnecting existing tanks of capacity exceeding 500 litre but not exceeding 1000 litre, setting aside (or lowering if required) for cleaning/roof repair etc. and hoisting, reconnecting and re-fixing in position after necessary cleaning by removing all scale and dirt etc. including cleaning mouth of circulating service pipes complete all as specified and directed

500 litre capacity, white, three layered polyethylene water storage tanks (cylindrical vertical with threaded lid) including hoisted and fixed in position, making connections, IN REPAIRS, complete all as specified including the following acessories: - (i) Gun metal ball valves, high pressure, with metal rod & high density plastic ball complete screwed for iron pipe or brass ferrule and fixed, IN REPAIRS, suitable for 20 mm bore GI pipe, complete all as specified. (iii) Gun-metal stop valve (quarter turn type) with MS lever handle, suitable for 20 mm bore GI tubes, ISI marked, screwed both ends for iron pipe, IN REPAIRS, complete all as specified. (iv) Provn of 20 mm bore GI light grade tube from O/H tank to nearest mouth of RWP, IN REPAIRS, complete all as specified.

1000 litre capacity, white, three layered polyethylene water storage tanks (cylindrical vertical with threaded lid) including hoisted and fixed in position, making connections, IN REPAIRS, complete all as specified including the following acessories: - (i) Gun metal ball valves, high pressure, with metal rod & high density plastic ball complete screwed for iron pipe or brass ferrule and fixed, IN REPAIRS, suitable for 20 mm bore GI pipe, complete all as specified. (iii) Gun-metal stop valve (quarter turn type) with MS lever handle, suitable for 20 mm bore GI tubes, ISI marked, screwed both ends for iron pipe, IN REPAIRS, complete all as specified and directed. (iv) Provn of 20 mm bore GI light grade tube from O/H tank to nearest mouth of RWP, IN REPAIRS, complete all as specified.

Steel tubes 15 mm bore ‘medium grade’, galvanized with all fittings and fixed to walls and ceilings or laid in floors, complete all as speciifed.

Steel tubes 20 mm bore ‘medium grade’, galvanized with all fittings and fixed to walls and ceilings or laid in floors, complete all as speciifed.

Angular stop valve/cock, cast copper alloy, chromium plated, with wall flange, quarter turn type, screwed end for iron pipe or for union and fixed, suitable for 15 mm bore pipe, IN REPAIRS, complete all as specified and directed. MAKE: PRAYAG Cat No. 6510 or equivalent make mentioned in Appendix 'B'.

Concealed stop valve/cock, cast copper alloy, chromium plated, with wall flange, quarter turn type, screwed end for iron pipe or for union and fixed, suitable for 15 mm bore pipe, IN REPAIRS, complete all as specified and directed. MAKE: PRAYAG Cat No. 6518 or equivalent make mentioned in Appndix 'B'.

Bib tap, cast copper alloy, chromium plated fancy type, long body with wall flange, quarter turn type, screwed end for iron pipe or for union and fixed, suitable for 15 mm bore pipe, IN REPAIRS, complete. MAKE: PRAYAG Cat No. 6508 or equivalent make mentioned in Appendix 'B'.

Centre hole basin mixer, cast copper alloy chromium plated, quarter turn type, screwed end for iron pipe or for union and fixed, suitable for 15 mm bore pipe, IN REPAIRS complete all as specified and directed. MAKE: KEROVIT Cat No. KB111027 or equivalent make mentioned in Appendix 'B'.'.

Wall mixer, cast copper alloy chromium plated, quarter turn type, screwed end for iron pipe or for union and fixed, suitable for 15 mm bore pipe, IN REPAIRS complete all as specified and directed. MAKE: KEROVIT Cat No. KB511021 or equivalent make mentioned in Appendix 'B'.'.

Sink mixer, cast copper alloy chromium plated, quarter turn type, screwed end for iron pipe or for union and fixed, suitable for 15 mm bore pipe, IN REPAIRS complete all as specified and directed. MAKE: KEROVIT Cat No. KB511024 or equivalent make mentioned in Appendix 'B'.'.

Overhead ABS shower with cast copper alloy chromium plated arm 225 mm long with flange and fixed in position, IN REPAIRS, complete. MAKE: PRAYAG Cat BS-76 or equivalent make mentioned in Appendix 'B'.

Vitreous China wash down water closet pan (pedestal pattern), white ISI marked, with & including stainless steel body Jet spray (L-bend) with 1.50 metre long braded tube tube, soft close PVC seat & cover and uPVC 'S trap, IN REPAIRS, complete all as specified and directed MAKE OF EWC: PRAYAG Cat No. 4016 or equivalent make mentioned in Appendix 'B'.

Vitreous China wash down water closet pan (One piece with cistern), white, ISI marked, with & including Health faust with 1 metre SS tube & hook with PP thin rim seat cover and necessary rag bolts, IN REPAIRS, complete all as specified. MAKE OF EWC: KEROVIT Cat No. KS709 or equivalent make mentioned in Appendix 'B'.

Vitreous China squatting pan, ‘Orissa’ pattern, size 580 x 440 mm, ISI marked, white, with integral foot rests (excluding flushing cistern and flush pipe), 110x125 size uPVC 'P' trap & necessary joints, lime concrete IN REPAIRS, complete all as specified and directed. MAKE: PRAYAG Cat No. 4055 or equivalent make mentioned in Appendix 'B'

Vitreous China wash hand basin, white, flat back, size 550 x 400 mm, ISI marked, including fixing acessories like rag bolts etc. with CP waste coupling half or full threaded suitable for & including 32 mm size PVC solid waste pipe, IN REPAIRS, complete all as specified. MAKE: PRAYAG Cat No. 4645 or equivalent make mentioned in Appendix 'B'

Health fauset with 1 metre SS tube & hook complete. MAKE: PRAYAG Cat No. BEA-97 or equivalent make mentioned in Appendix 'B'.

PVC flushing cistern 10 litre capacity, syphonic action type, any shade, dual flush, ISI marked with flush pipe and all fixing acessories, IN REPAIRS, complete all as specified and directed. MAKE: PRAYAG Cat No. 502 or equivalent make mentioned in Appendix 'B'

Corner Glass shelf 300 mm with brass brackets and fixed to wall with chromium plated brass screws and rawl plugs, IN REPAIRS, complete. MAKE: PRAYAG Cat No. BEA-44 or equivalent make mentioned in Appendix 'B'.

Brass chromium plated towel rail 500-600 mm long, fixed to wall with SS screws and PVC rawl plugs, IN REPAIRS, complete all as specified and directed. MAKE: PRAYAG Cat No. BA-10 or equivalent make mentioned in Appndix 'B'.

Stainless steel soap dish, fixed to wall with SS screws and PVC rawl plugs, complete all as specified and directed. MAKE: PRAYAG Cat No. BA-05 or equivalent make mentioned in Appendix 'B'.

Stainless steel round slotted grating with frame, 100 mm size fixed in position with cement joints, IN REPAIRS, complete all as specified and directed.

PVC connections with PTMT nuts, 450 mm long, IN REPAIRS, complete all as specified and directed.

Stainless steel peg set of six, fixed to wall with SS screws and PVC rawl plugs, complete all as specified and directed. MAKE: PRAYAG Cat No. BEA-30 or equivalent make mentioned in Appendix 'B'.

Stainless steel sink with drainage board made out of 1.00mm thick sheet for kitchen or laboratory with plug waste pipe washers including cantilever cast iron brackets connecting union etc overall size 940mm x 460mm x 203 mm with bowl size 354mmx 405mmx 203mm,IN REPLACEMENT complete all as specified and directed. MAKE:PRAYAG Cat No. 1342D or equivalent make mentioned in Appndix 'B'.

uPVC pipes 75 mm external dia, type-B, ISI marked (IS:13592) single socketed in any length with rubber ring joints, fixed under floors/walls as SWR pipes, IN REPAIRS, complete all as specified and directed.

uPVC pipes 110 mm external dia, type-B, ISI marked (IS:13592) single socketed in any length with rubber ring joints, fixed under floors/walls as SWR pipes, IN REPAIRS, complete all as specified and directed.

uPVC/PVC bend any radius, suitable for uPVC soil waste discharge pipes 75 mm external dia, IN REPAIRS, complete all as specified and directed.

uPVC/PVC bend any radius, suitable for uPVC soil waste discharge pipes 110 mm external dia, IN REPAIRS, complete all as specified and directed.

uPVC/PVC single T, equal or unequal, suitable for uPVC soil waste discharge pipes 75 mm external dia, IN REPAIRS, complete all as specified and directed.

uPVC/PVC single T, equal or unequal, suitable for uPVC soil waste discharge pipes 110 mm external dia, IN REPAIRS, complete all as specified and directed.

uPVC floor trap, suitable for uPVC soil waste discharge pipes 75 mm ext dia, embedded in PCC type B-1(1:2:4), IN REPAIRS, complete all as specified and directed,

INTERNAL ELECTRIFICATION WORKS

Point wiring with multi-stranded copper conductor, single core, FRLSH PVC insulated and unsheathed cable, including FRLSH PVC insulated unsheathed stranded copper conductor single core cable as earth continuity conductor to common earth and connected to earth dolly, comprising the following: -

One light point controlled by one switch or one fan point controlled by one switch & fan regulator etc. or for bell/buzzer with 1.5 Sq. mm (nominal area) cable & 1.5 Sq. mm (nominal area) cable as earth continuity conductor, in existing concealed conduit complete all as specified and directed.

One light point controlled by two no., 2 way switches with 1.5 Sq. mm (nominal area) cable & 1.5 Sq. mm (nominal area) cable as earth continuity conductor, in existing concealed conduit complete all as specified and directed.

One Socket outlet three pin, 6 Amp, on the same board, with 1.5 Sq. mm (nominal area) cable & 1.5 Sq. mm (nominal area) cable as earth continuity conductor, all as specified.

One Socket outlet three pin, 6 Amp, independent, with 1.5 Sq. mm (nominal area) cable & 1.5 Sq. mm (nominal area) cable as earth continuity conductor, in existing concealed conduit complete all as specified and directed.

One socket outlet three pin, 6/16 Amp, independent, with 2.5 Sq. mm (nominal area) cable & 2.5 Sq. mm (nominal area) cable as earth continuity conductor, in existing concealed conduit complete all as specified and directed.

Point wiring with multi-stranded copper conductor, single core, FRLSH PVC insulated and unsheathed cable, including FRLSH PVC insulated unsheathed stranded copper conductor single core cable as earth continuity conductor to common earth and connected to earth dolly comprising the following: -

One light point controlled by one switch or one fan point controlled by one switch & fan regulator etc. or for bell/buzzer with 1.5 Sq. mm (nominal area) cable & 1.5 Sq. mm (nominal area) cable as earth continuity conductor, in and including rigid non metallic PVC medium duty concealed conduit complete all as specified and directed.

One light point controlled by two no., 2 way switches with 1.5 Sq. mm (nominal area) cable & 1.5 Sq. mm (nominal area) cable as earth continuity conductor, in and including rigid non metallic PVC medium duty concealed conduit all as specified.

One Socket outlet three pin, 6 Amp, on the same board, with 1.5 Sq. mm (nominal area) cable & 1.5 Sq. mm (nominal area) cable as earth continuity conductor, all as specified.

One Socket outlet three pin, 6 Amp, independent, with 1.5 Sq. mm (nominal area) cable & 1.5 Sq. mm (nominal area) cable as earth continuity conductor, in and including rigid non metallic PVC heavy duty concealed conduit all as specified.

One socket outlet three pin, 6/16 Amp, independent, with 2.5 Sq. mm (nominal area) cable & 2.5 Sq. mm (nominal area) cable as earth continuity conductor, in and including rigid non metallic PVC medium duty concealed conduit all as specified.

NOTES: (a) Switch(es) & socket(s) shall be measured & paid for separately under respective item of Schedule 'A'. (b) GI boxes shall be fixed flush to walls in position with cement mortar (1:4) complete all as directed. (c) Conduit shall be laid on surface in case of RCC ceiling surfaces.

Switch piano flush button single pole one way, 6 Amp complete all as specified.

Switch piano flush button single pole two way, 6 Amp complete all as specified.

Switch piano, bell/buzzer push, flush button single pole one way, 6 Amp complete all as specified.

Switch piano flush button single pole one way, 16 Amp complete all as specified.

Socket outlet multipurpose having provision for 2&3 pin, 6 Amp, flush type, complete all as specified.

Socket outlet multipurpose having provision for two-in-one 3 pin 6 Amp & 3 pin 16 Amp, flush type complete, all as specified.

Ceiling rose, surface bakelite, 65 x 50mm, three terminals complete, all as specified.

Lamp (angle) holder, insulated body, cord grip pattern, complete, all as specified.

Electric buzzer AC 230 volt, single pole, Ding Dong type complete, all as specified.

Fan regulator (electronic) suitable for 48”/56” sweep fan, stepped type, single phase, complete all as specified.

Sub main wiring (with approved colour coding as per IS) with single core FRLSH PVC insulated flexible stranded copper conductor 1.1 KV grade (main cable: number of runs as indicated below along with single core FRLSH PVC insulated flexible stranded copper conductor 1.1 KV grade for earthing in conduits, complete all as specified for the following: -

2 runs of 4 Sq. mm main cable + 1 run of 4 Sq. mm earth cable.

2 runs of 6 Sq. mm main cable + 1 run of 6 Sq. mm earth cable.

NOTES: (i) Conduit & conduit accessories shall be measured & paid for separately. (ii) For payment purposes, total runs of main cable (Two run of one running metre) as mentioned above and one run (one running metre) of earth cable shall be considered together as "1 RUNNING METRE"

Rigid non metallic, PVC concealed conduit, 20 mm bore, medium grade, ISI marked, inclusive of all fitings (such as junction boxes, bends, elbows, tees, reducers, bell mouth tube ends) and all fixing acessories such as couplers, lock nuts, saddles, pipe hook etc. for sub main wiring and the like complete all as specified.

Sheet metal enclosure for DB for fixing MCB’s, isolators etc., having IP-43 protection, suitable for surface and flush mounting, complete all as specified comprising the following: -

SPN, 8 way with 200 Amp rated bus bar, 240 V, double door type.

SPN, 12 way with 200 Amp rated bus bar, 240 V, double door type.

TPN, 4 way with 200 Amp rated bus bar, 415 V, double door type having housing and including MCCB 4 pole 40 Amp, 26kA.

MCB suitable for 240 volt AC supply, SP with over load and short circuit protection and rupturing capacity not less than 10 kA, 'C' curve type of rating 6 to 32 Amp complete all as specified and directed.

MCB suitable for 240 volt AC supply, SPN with over load and short circuit protection and rupturing capacity not less than 10 kA, 'C' curve type of rating 6-32 Amp complete all as specified and directed.

Blanking plate to cover unused space in DB's complete all as specified and directed..

Single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB 20 Amp, 240 volt, breaking capacity not less than 10 kA, complete all as specified and directed.

Environment friendly, modern design, energy saving surface mounted, decorative 10 W bulk head LED luminaire with premium quality diffuser for glarefree light, 6000K, including making connections, complete all as specified and directed. MAKE: Havells Cat No. HEXAFT10WLED857SSYMBOPC or equivalent in makes mentioned in Appendix 'B' here-in-after.

Surface mounted environment friendly LED batten with powder coated aluminium housing with intigrated electronic driver with THD<10% LED 10W lighting fixture 2 feet long, 6500K, lumen output should not be less than 90 lumens per watt, including making connections, complete all as specified and directed. MAKE: Havells Cat No. ENDURALINEARNEOBS10WLED865SPCWH or equivalent in makes mentioned in Appendix 'B' here-in-after.

Surface mounted environment friendly with eye soft technology & glarefree diffuser LED 20 W lighting , 6500K, lumen output should not be less than 90 lumens per watt complete all as specified and directed. MAKE: Havells Cat No. ENDURALINEARNEOBS20WLED865SPCWH or equivalent in makes mentioned in Appendix 'B' here-in-after.

Collecton of items like ceiling fans, exhaust fans, wall mounted fans, cabin/table fans, flame proof ceiling fans from EM store yard for repair, transporting to workshop, opening and reassembling after including necessary cleaning greasing oiling etc, testing and depositing back to EM store yard of GE (AF) Adampur including necessary loading unloading and transporting etc. complete all as specified and directed. NOTE: Supply only spares & rewinding of fan(s) shall be measured & paid for separately under respective items of BoQ.

Rewinding fan of any description with super enamelled copper winding wire of size, gauge & weight as per original specifications providing insulating material and varnishing with synthetic varnish, oiling, greasing including replacement of bush/bearing, condenser, 'U' clamp with reel to the entire satisfaction of Engineer-in-Charge including taking out burnt winding wire after opening the ceiling fan and other unserviceable parts, of size: -

Ceiling fan 1200 mm sweep

Ceiling fan 1400 mm sweep

Exhaust fan 300 mm sweep

Exhaust fan 380 mm sweep

Wall mounted fan of various sweep

NOTE: Collecton of fan items from EM store yard, transporting to workshop and back including loading unloading shall be measured & paid for separately under respective items of BoQ.

Earthing with and including GI earth plate electrode 6 mm thick of size 600 mm x 600 mm with 4 Sq.mm GI wire earthing lead complete all as shown in electrical plate No. 3 and as specified in Particular Specifications clause 19.5.1 of contract, IN REPAIR/REPLACEMENT .

NOTES :- (a) The unit rate includes earthing lead and protection pipe upto 7.5 metre from top of earth plate. (b) Factory made PCC pit with cover shall be fixed at least 500 mm away from earth pit. (c) Earth resstance shall be less than 3 ohm. In case the test results are not found less than 3 ohm, complete earthing shall be redone by the contractor without any extra cost to Govt.

GI terminal boxes 50mm deep with 3 mm thick plastic laminated sheet cover and fixing of existing switches seeks regulator etc , of size: -

DISMANTLING/DEMOLITION WORKS

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) area not exceeding 1.50 Sq.m each and removing from site all as specified and directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) area exceeding 1.50 Sq.m but not exceeding 4.00 Sq.m each and removing from site all as specified and directed.

Taking down shutters of any description exceeding 1 Sq. m but not exceeding 2 Sq. m each and removing from site complete all as specified and directed.

Taking down shutters of any description exceeding 1 Sq. m but not exceeding 2 Sq. m each, including stacking at directed location and refixing the same on original or new location after resecuring or easing & adjusting, complete all as specified and directed.

Taking down cement plaster of any description on brick walls or concrete surfaces etc including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

Taking up or down steel tubing 15 mm bore and connections, including cleaning for re-fixing or removal to store complete all as specified and directed.

Taking up or down steel tubing 20 mm bore and connections, including cleaning for re-fixing or removal to store complete all as specified and directed.

Demolition brickwork or stone / boulder masonry built in cement mortar including all quoins, arches, pillars etc complete all as specified and directed

Demolition of cement concrete (unreinforced) in ground floors and pavings not excceding 15cm thickness (above or below ground level) complete all as specified and directed.

Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided complete all as specified and directed.

Demolition of reinforced concrete of any description and in any position not otherwise specifically provided for (reinforcement cut as required to facilitate demolition) complete all as specified and directed.

Dismantling boarding, any description, fixed in any position complete all as specified and directed.

Dismantling asbestos cement (corrugated, semi-corrugated, etc.) sheets in roof coverings, complete all as specified and directed.

Demolition of mud phuska in roofs, of thickness not more than 200 mm including plaster and leeping plaster complete all as specified and directed.

Dismantlig brick tiles in roof laid dry and pointed in cement mortar complete all as specified and directed.

Dismantling wall and ceiling boards (fibre, pulp, gypsum, POP, insulation, etc.) or insulation boards/slabs/blankets, any thickness, including cover fillets complete all as specified and directed.

Taking down carefully copper/aluminium point wiring (light, fan, socket or power) complete with batten, casing caping of MS or and PVC conduit on surface or concealed, including switches, ceiling roses, pendants, regulators, sockets, mild steel terminal boxes etc., removing materials and making good disturbed surfaces due to taking down etc. to the entire satisfaction of Engineer-In-Charge, complete all as specified.

Taking down carefully copper/aluminium sub main wiring complete, including existing batten/conduit consealed/surface etc., removing materials and making good disturbed surfaces due to taking down etc. to the entire satisfaction of Engineer-In-Charge, complete all as specified and directed.

Dismantling of unservisible existing DBs of any description with all accessories and MCBs, isolators etc. and making good surface as per existing, complete all as specified and directed.

Taking down carefully light fitting of any description, complete all as specified and directed.

Taking down carefully electric bell/buzzer of any description, complete all as specified and directed.

Notes: Amount of credit for retrieved materials is mentioned in tender documents in pdf form which will be deducted while acceptance of tender offline.

M/S GURBACHAN SINGH (BID ID -3117102)

ELECTRA ENGINEERS (BID ID -3117800)

M/s Sahib and Company (BID ID -3115829)

AAR KAY BEE ENTERPRISES (BID ID -3116648)

J.K & Company (BID ID -3117252)

BHARAT ENTERPRISES (BID ID -3117243)