PROVN OF SURGICAL AND MEDICAL WARD FOR GH AT FEROZEPUR CANTT

Amount

Note: (i) Please refer Schedule 'A' Notes given on serial page No. 22 to 29 of tender documents. (ii) Item from Srl No. 3.00 to 10.17 of this document shall be Part-XVII (Miscellaneous items) of BOQ.

LUMPSUM/ OTHER PRE-PRICED PROVISIONAL SCHEDULES OF WORKS

Lump sum price worked out by the contractor for BUILDING WORKS as listed in Schedule 'A' Part-I brought forward from serial page No. 30.

Lump sum price worked out by the contractor for INTERNAL ELECTRIFICATION WORKS as listed in Schedule 'A' Part-II brought forward from serial page No. 32.

Lump sum price worked out by the contractor for INTERNAL WATER SUPPLY WORKS as listed in Schedule 'A' Part-III brought forward from serial page No. 33.

Lump sum price worked out by the contractor for SEWAGE DISPOSAL WORKS as listed in Schedule 'A' Part-IV brought forward from serial page No. 35.

Lump sum price worked out by the contractor for ROAD, PATH, CULVERT AND PCC HARDSTANDING WORKS as listed in Schedule 'A' Part-V brought forward from serial page No. 36.

Lump sum price worked out by the contractor for AREA DRAINAGE WORKS listed in Schedule 'A' Part-VI brought forward from serial page No. 37.

Lump sum price worked out by the contractor for SITE CLEARANCE AND EARTH WORKS as listed in Schedule 'A' Part-VII brought forward from serial page No. 38.

Lump sum price worked out by the contractor for BOUNDARY WALL, FENCING/ GATES WORKS listed in Schedule 'A' Part-VIII brought forward from serial page No. 39.

Lump sum price worked out by the contractor for HOT WATER SUPPLY WORK as listed in Schedule 'A' Part-IX brought forward from serial page No.40.

Lump sum price worked out by the contractor for EXTERNAL ELECTRIFICATION WORKS as listed in Schedule 'A' Part-X brought forward from serial page No. 43.

Lump sum price worked out by the contractor for EXTERNAL WATER SUPPLY WORKS as listed in Schedule 'A' Part-XI brought forward from serial page No. 44.

Lump sum price worked out by the contractor for LIGHTENING PROTECTION WORKS as listed in Schedule 'A' Part-XII brought forward from serial page No. 45.

Lump sum price worked out by the contractor for FIRE FIGHTING, FIRE PROTECTION AND FIRE ALARM WORKS as listed in Schedule 'A' Part-XIII brought forward from serial page No. 47.

Lump sum price worked out by the contractor for SUMMER APPLIANCES WORKS as listed in Schedule 'A' Part-XIV brought forward from serial page No. 48.

Lump sum price worked out by the contractor for LIFT WORKS as listed in Schedule 'A' Part-XV brought forward from serial page No. 49.

Lump sum price worked out by the contractor for DEMOLITION/ DISMANTLING WORKS as listed in Schedule 'A' Part-XVI brought forward from serial page No. 50.

INTERNAL ELECTRIFICATION WORKS

Material and labour for concealed point wiring complete with 1.5 sqmm (nominal cross sectional area) FRLS PVC insulated multi-stranded copper conductor in and including heavy duty PVC conduit pipe (ISI marked) including fittings & accessories including MS concealed terminal boxes with 3mm thick plastic laminated bakelite (Hylum) sheet top cover for mounting switch socket etc including 1.5 sqmm FRLS PVC copper conductor multi-stranded as earth wire connected to the common earth dolly as specified for one light point/fan point/bell point controlled by one switch complete all as specified and directed.

All as per item No. 3.01 above but one three pin socket outlet 5 Amp on same board.

All as per item No. 3.01 above but one three pin socket outlet 5 Amp on independent board.

All as per item No. 3.01 above but one light point controlled by 2 way switch.

All as per item No. 3.01 above but with 2.5 sqmm cable and 1.5 sqmm copper conductor as earth wire for 3 pin, 15 Amps socket outlet complete.

Supply and fixing of handset remote for nurse call bell system for each bed for paitent to nurse call bell system complete all as specified and directed.

Supply, fixing and testing of console for 16 beds (Nursing Station) i.e paitent to nurse call bell ststem for special and semi special beds, ICU, OT and trauma including all connected items and wiring circuits from each bed to console complete all as specified and directed.

Supply and fixing batten holder insulated body including LED lamp 10 W 220-240 volts, 6500K, B-22 base cap complete all as specified and directed.

Supply and fixing ceiling fan 1200mm sweep BEE 5 star rated including provision of cord flexible copper conductor 23/0.0076 three core from ceiling rose to connector including GI pipe down rod of suitable dia 450 mm long all as specified and directed.

Supply and fixing exhaust fan heavy duty steel body with louvers complete of 300mm size with bolts,nuts and washers, size of the bolt 15 cm long 12mm dia embedded in the wall including provision of PVC flexible copper cable of size 23/00.0076 three core from ceiling rose to exhaust fan for giving connection complete allas specified. Note: Cost of opening in wall and grouting of mild steel work shall be deemed included in the lump sum cost of the building.

Supply and fixing for energy saving tube light luminaires with diffuser LED comprising with CRCA MS box and for fit 18 to 20 watt (max) of 1200mm length retro fit tube rod having thermally conductive material heat sink, lumen output 2100 lumens (min) 6500K, power factor more than 0.95, IP 20 class-I protection with inbuilt LED driver surge protection device, operative on 140-270 volts AC supply complete pre-wired, connection and testing complete all as specified and directed.

Supply and fixing for energy saving and environmental friendly long life versatile pressure die cast aluminium housing luminaire with heat resistant glass and suitable optics for uniform distribution of light 25 watt LED for bldg security light with high efficiency electronic driver, having IP-65 protection, surge protection device, power factor more than 0.9 complete operative on AC supply 140-270 volts pre wired and product should be made in India only complete all as specified and directed.

Supply and fixing MCB, single pole 240 volts, capacity 6 - 32 Amps, C series 50 Hz, 10 KA complete all as specified and directed.

Supply and fixing for MCB, SPN 240 volts, capacity 40 Amps, C series 50 Hz, 10 KA complete all as specified and directed.

Supply and fixing sub main wiring with two single core FRLS PVC insulated stranded copper conductor 4 Sqmm and 1 x 4 Sqmm for earth continuous earth wire including suitable PVC conduit medium grade ISI marked all as specified and directed. Note : Two runs of PVC cable 4 sqmm & one run of earth wire 4 sqmm will be considered as one unit.

Supply and fixing sub main wiring with two single core FRLS PVC insulated stranded copper conductor 6 Sqmm and 1 x 6 Sqmm for earth continuous earth wire including suitable PVC conduit medium grade ISI marked all as specified and directed. Note : Two runs of PVC cable 6 sqmm & one run of earth wire 6 sqmm will be considered as one unit.

Supply and fixing sub main wiring with two single core FRLS PVC insulated stranded copper conductor 10 Sqmm and 1 x 10 Sqmm for earth continuous earth wire including suitable PVC conduit medium grade ISI marked all as specified and directed. Note : Two runs of PVC cable 10 sqmm & one run of earth wire 10 sqmm will be considered as one unit.

Supply and fixing sub main wiring with four single core FRLS PVC insulated stranded copper conductor 6 Sqmm and 2 x 6 Sqmm for earth continuous earth wire including suitable PVC conduit medium grade ISI marked all as specified and directed. Note : Four runs of PVC cable 6 sqmm & two run of earth wire 6 sqmm will be considered as one unit.

Supply and fixing sub main wiring with four single core FRLS PVC insulated stranded copper conductor 10 Sqmm and 2 x 10 Sqmm for earth continuous earth wire including suitable PVC conduit medium grade ISI marked all as specified and directed. Note : Four runs of PVC cable 10 sqmm & two run of earth wire 10 sqmm will be considered as one unit.

Supply and fixing sub main wiring with four single core FRLS PVC insulated stranded copper conductor 16 Sqmm and 2 x 16 Sqmm for earth continuous earth wire including suitable PVC conduit medium grade ISI marked all as specified and directed. Note : Four runs of PVC cable 16 sqmm & two run of earth wire 16 sqmm will be considered as one unit.

Supply and fixing blanking plate complete all as specified and directed.

Material and labour for earthing complete with galvanized steel earth plate electrode 600mm x 600mm x 6mm thick buried directly in ground vertically to a depth not less than 2.25 metre below ground level with top edge of the earth plate at a depth not less than 1.5 metre below ground level, earth plate surrounded by 15cm thick and packed with layers of charcoal dust and common salt, earth lead GI wire 4mm dia (8 SWG) connected to GI earth plate electrode by means of bolts, nuts, check nuts and washers of galvanized iron and thimbles and other end of earth wire connected to main switch board and protected by galvanized iron medium grade 15mm bore and GI pipe 20mm bore light grade with funnel and wire mesh for watering including necessary excavation and earth works. PCC Chamber in cement concrete (1:3:6) type C-2 & RCC cover in M-20 (Design mix) and all as shown in Electrical Plate No 3 of MES standard Schedule of Rates (Part-I) of 2009 complete all as specified and directed. Notes : (i) Outer edge of earth pit will be 1 m away from the outer edge of PCC chamber. (ii) GI earth wire upto main board is included in this item. (iii) Water pipe shall be provided in slanting position.

Supply and fixing square pure white 18 watt LED, ceiling mounted light, fixing in 2' x 2' tile complete with driver and connected accessories all as specified and directed

INTERNAL WATER SUPPLY WORKS

Supply and fixing 15mm bore, PVC body health faucet with 1.2m PVC connection pipeand hooks complete all as specified and directed

HOT WATER SUPPLY WORKS

Supply, fixing, connecting and testing energy efficient (BEE 5 Star rated) electric water heater vertical storage type of 25 Ltr capacity with stainless steel inner tank, brass assembly, pressure release valve, heating element 1500/2000 W including all other accessories with high quality external finishes single phase with working volatage 240 volts, 50 Hz, ISI marked complete all as specified and directed. Make : Havells Model No. NaZZ, Part No. GHWENZTWG025 or equivelant to Bajaj/ CG/ RECOLD Note :The cost of fixing of geysers including stud/ nuts/ fastners, bolts, washers and making good the disturbed surfaces to match with the existing surface is deemed to be included in the unit rate quoted.

Supply and fixing PVC connection 15mm size with brass nuts of length 450mm for Hot/ Cold water supply complete all as specified and directed.

EXTERNAL ELECTRIC SUPPLY WORKS

(C) OUTDOOR ENCLOSURE : Outdoor type enclosure made of minimum 1.5mm thick GI/ CRCA MS sheet. The enclosure shall have IP 54 degree of protection for HT & LT switchgear for transformer compartment. The enclosure exterior shall be polyurethane metallic painted. Each compartment will be provided with the door and pad locking arrangement. The compartment illumination lamp with door operated switch shall be provided for each compartment, interconnection between HT switchgear & transformer using XLPE single core cable & interconnection between transformer & LT switchgear using bus bars internal earthing connection. All metallic components shall be earthed to a common earthing point. (D) TRANSFORMER : 315 KVA, 11 KV/433V, DYn 11, ONAN, hermetically sealed with corrugated tank design, copper wound, oil type transformer with off load tap changer of plus/ minus 2.5% to 7.5% in steps of 2.5% with initial filling of oil. (E) INTERCONNECTION & EARTHING : Internal factory connection between HT switchgear & transformer shall be done using IC x 3 x 95 Sqmm XLPE single core cable & interconnections between transformer & LT switchgear using bus bars. Internal earthing connections. All metallic components shall be earthed to a common earthing point.

Supplying, installing and testing out door type 11 KV, VCB panel switch 630 Amp conforming to IEC 62271, as per IS 13118 totally enclosed single busbar floor mounting (floor rolling VCB) metal clad, indoor extendable type flush fronted with horizontal isolation horizontal draw out type powder coated of paint shade RAL 7032 vacuum circuit breaker suitable for installation in 3 wire, 50 Hz, 11 KV effectively earthed supply system comprising of housing of breaker, mechanical interlock, safety shutter isolating plugs and M-2 class type tested VCB trolley with three vacuum interrupter, epoxy support insulator and self aligning finger type isolating contracts, truck having integral locking-in device for insertion and withdrawal of VCB complete with necessary interlocks, manual charged independent spring closing/ spring tripping, trip free operating mechanism with manual closing and tripling push buttons, mechanical indications viz braker “CLOSED/ OPEN” spring “CHARGED/ DISCHARGED” mechanical operation counter, electrical operation counter, electrical release coil, breaker operated auxiliary switch with 6 Nos and 6 NC spare contacts type : 230V AC operated motorized mechanism + manual arrangement & switch gear panel shall be steel enclosure of minimum 2mm thick with protection class IP54 with following features each braker should have three position test, service, isolated/ withdrawal position :- (A) VCB CONSIST OF (i) Busbar chamber with copper busbars of 630 Amps (PVC sleeved)-01 No (ii) Electrical closing coil 30V DC-01 No (iii) Electrical shunt trip coil 30V DC-01 No (iv) 02 Nos 60W, 230V AC each with timer controlled and switch for isolation. A hygrostat control unit with variable temperature and humidity control setting shall be installed to control the heater. The 240V AC supply for the heater shall be controlled by a suitably rated single pole miniature circuit breaker. (v) Rear cable box suitable for 3 core, 11 KV, 95/120 Sqmm XLPE cable-01 No (vi) CURRENT TRANSFORMER : Triple core, dual ratio, cast resin, indoor type, E class insulation current transformers of core 1 class 1.0 accuracy and core 2 class 5P10. STR of CT 18.4 KA for 1.0 sec 5/15 VA burden, -03 Nos for each VCB (CT ratio 200/100/5+5 CT shall be conforming to IS 3156

(xxii) Push button for cancellation (xxiii) Breaker control switch (xxiv) Local/ Remote switch (xxv) HRC links (xxvi) HRC fuse holder (xxvii) Thermostat (xxviii) 3 pin socket with switch (xxix) Tapping coil 30 V DC (xxx) Closing coil 30V DC

Supplying, installing and testing out door type 11 KV, VCB panel switch 630 Amp conforming to IEC 62271, as per IS 13118 totally enclosed single busbar floor mounting (floor rolling VCB) metal clad, indoor extendable type flush fronted with horizontal isolation horizontal draw out type powder coated of paint shade RAL 7032 vacuum circuit breaker suitable for installation in 3 wire, 50 Hz, 11 KV effectively earthed supply system comprising of housing of breaker, mechanical interlock, safety shutter isolating plugs and M-2 class type tested VCB trolley with three vacuum interrupter, epoxy support insulator and self aligning finger type isolating contracts, truck having integral locking-in device for insertion and withdrawal of VCB complete with necessary interlocks, manual charged independent spring closing/ spring tripping, trip free operating mechanism with manual closing and tripling push buttons, mechanical indications viz braker “CLOSED/ OPEN” spring “CHARGED/ DISCHARGED” mechanical operation counter, electrical operation counter, electrical release coil, breaker operated auxiliary switch with 6 Nos and 6 NC spare contacts type : 230V AC operated motorized mechanism + manual arrangement & switch gear panel shall be steel enclosure of minimum 2mm thick with protection class IP54 with following features each braker should have three position test, service, isolated/ withdrawal position :- (A) VCB CONSIST OF (i) Busbar chamber with copper busbars of 630 Amps (PVC sleeved)-01 No (ii) Electrical closing coil 30V DC-01 No (iii) Electrical shunt trip coil 30V DC-01 No (iv) 02 Nos 60W, 230V AC each with timer controlled and switch for isolation. A hygrostat control unit with variable temperature and humidity control setting shall be installed to control the heater. The 240V AC supply for the heater shall be controlled by a suitably rated single pole miniature circuit breaker. (v) Rear cable box suitable for 3 core, 11 KV, 95/120 Sqmm XLPE cable-01 No (vi) CURRENT TRANSFORMER : Triple core, dual ratio, cast resin, indoor type, E class insulation current transformers of core 1 class 1.0 accuracy and core 2 class 5P10. STR of CT 18.4 KA for 1.0 sec 5/15 VA burden, -03 Nos for each VCB (CT ratio 200/100/5+5 CT shall be conforming to IS 3156

(xxii) Multi-pin socket (xxiiii) Alarm bell 30V DC against over current & earth fault (xxiv) Push button for cancellation (xxv) Breaker control switch (xxvi) Local/ Remote switch (xxvii) HRC links (xxviii) HRC fuse holder (xxix) Thermostat (xxx) 3 pin socket with switch (xxxi) Tapping coil 30 V DC (xxxii) Closing coil 30V DC Notes for Srl No. 6.03 & 6.04 :- (i) VCB comprises of one incomer and two outgoing (ii) VCB to be coupled with existing VCB panel including addition alteration if required including materials & connecting to bus bar of existing size for rate for which is deemed to be included in the unit rate. (iii) Calibration of relay shall be carried out site by the technician/ service engineer of manufacturer as per feederwise protection as directed by Engineer-in-Charge. (iv) DC 30V supply for relay is to be connected to the existing system necessary wiring required shall be deemed to be included in the item rate. (v) Any other parts/ items not specified above but have been considered but essential for smooth functioning of the switchgear shall be included in the item rate and are covered against in the item rate. (vi) VCB & vacuum interrupter shall be of make i.e. VCB panel manufacturer only.

Material & labour earthing complete with galvanized steel earth plate electrode 60cm x 60cm x 6.3mm thick buried directly in ground vertically to a depth not less than 2.25 metre below ground level with top edge of the earth plate at a depth not less than 1.5 metre below ground level, earth plate surrounded by 15cm thick and packed with layers of charcoal dust and common salt, earth electrode GI strip 32 x 6mm dia connected to GI earth plate electrode by means of bolts, nuts, check nuts and washers of galvanized iron and thimbles and other end of earth wire connected to main switch board and protected by galvanized iron light grade 40mm bore and GI pipe 20mm bore medium grade with funnel and wire mesh for watering including necessary excavation and earth works. PCC chamber in cement concrete (1:3:6) type C-2 using graded stone aggregate and RCC cover in M-25 (Design mix) and all as shown in Electrical Plate No. 3 of MES Schedule (Part-I) of 2009 complete all as specified and directed. (Qty '10 Nos' for External Electrification Works, Qty '25 Nos' for Lightening Protection Works & Qty '14 Nos' for Fire Fighting, Fire Protection and Fire Alarm Works) Notes (i) The unit rate shall include for protection pipe, GI water pipe, funnel, wire mesh excavation, RCC pit cover, test point, 32 x 6mm galvanised strip for top of earth plate upto 5m above ground level and if GI protection is les than 5m, no price adjustment shall be made (ii) PCC pit shall be provided at least 50cm away from the earth pit and not just on the earth pit and extra cost of additional length of water pipes and fittings, junction, elbow etc shall be deemed to be included in the unit rate. (iii) If the testing resulut of earth work is not been found satisfactory then the contractor shall do other earthing work at his own cost and nothing shall be permissible on this account (iv) Earthing work will be carried out in presence of MES representative.

Supply and fixing GI bracekt for street light fitting bend to shape made out of GI pipe light grade 35mm-40mm bore upto 1.2m long etc complete with two sets of MS flat clamps of size 45x5mm duly painted with two coat of aluminium paint with nuts/ bolts/ washers for fixing arrangement to pole/ wall complete all as specified and directed

Supply and fixing LED street light 70 watt 5700K made up of pressure die cast housing with toughned glass and individual high power LED with secondary optics, with IP-66 protection and impact resistance of IK-07 complete all as specified and directed Make : Havells cat part No. ENDURAPEARLPLUS70WLED757SASYTOPC or equivalent to Crompton/ Bajaj

Supply and fixing IP-65 modular box made of impact resistance plastic & heat resistant matrials of size 205 x 255 x 112mm with transparent lid including provision of MCB SP 2.5 Amp, terminal 4 way connector and fixing to the street light pole/ pipe with suitable sizes of clamps, nuts and bolts complete all as specified and directed

Material and labour for multi core aluminium stranded wire of size 2.5 sqmm for street light connection from junection box to street light inside the pole and through street light bracket complete all as specified and directed

DG Sets Supply, install, testing and commissioning of diesel engine driven Generating set with acoustic enclsoure (Silent Version) conforming to latest CPCB Norms of 300 KVA/ 240 KW capacity, radiator water cooled, Diesel engine driven developing 326 BHP at 1500 RPM coupled with alternator of capacity 300 KVA/ 240 KW delivering out put Voltage 415 Volts +/- 1.0% at set value of 415 V at a frequency 50HZ +/- 0.5% with suitable AVR control panel, all mounted in acoustic enclosure and AMF Logic panel all as per manufacturers design and specification as per CPCB norms confirming to the detailed specifications appended below :- Make : KIRLOSKAR GREEN / CUMMINS/GREAVES COTTON/STAMFORD (i) ENGINE :- (a) General: Suitable for four stroke compressed ignition, radiator water cooled, continuous duty with 10% overload capacity for any one hour in 12 hours running, 50°C intake air temperature. The prime mover provided should be as per IS specifications. (b) Air intake system : Should comprise of dry type intake air filter mounted on engine, one in number vacuum indicator mounted on intake piping. (c) Exhaust System: Should comprise of one exhaust manifold, dry type, mounted on engine, one exhaust silencer which should be positioned in such a way that the exhaust gas is not sucked by the fan on the radiator, thereby affecting the cooling system. The silencer should cater to the noise level tolerance prescribed in the relevant IS/BS. The silencer should be provided with flaps with a provision so that it will open only when the generator is running. The complete exhaust system shall be properly supported so that entire load of the exhaust system shall not fall on the DG Set. A sufficient length of straight pipe shall be provided after the exhaust silencer to leave the gases at sufficient height above the engine and outside the room. (d) Fuel System: Should comprise of disposal type element fuel filter, pressure type fuel pump mounted on engine, non return check valve in fuel supply and drain lines, wire braided hose between filter and pump, The fuel tank must have proper locking arrangement. (e) Cooling System: Should comprise of radiator with 7 PSI pressure cap mounted on base rail. The thermostat installed in the engine coolant outlet, fresh water pump mounted on engine, fan and fan hub mounted on engine.

Supply and install ON LOAD change over switch 415 Volt in sheet metal enclosure 4 pole of capacity 800 Amps (suitable for open executiom and to be fitted in the standard control panel) complete all as specified and directed.

Material & labour earthing complete with galvanized steel earth plate electrode 60cm x 60cm x 6mm thick buried directly in ground vertically to a depth not less than 2.25 metre below ground level with top edge of the earth plate at a depth not less than 1.5 metre below ground level, earth plate surrounded by 15cm thick and packed with layers of charcoal dust and common salt, earth electrode GI strip 20 x 3mm connected to GI earth plate electrode by means of bolts, nuts, check nuts and washers of galvanized iron and thimbles and other end of earth strip connected to test point and protected by galvanized iron light grade 15mm bore and GI pipe 20mm bore medium grade with funnel and wire mesh for watering including necessary excavation and earth works. PCC chamber in cement concrete (1:3:6) type C-2 using graded stone aggregate and RCC cover in M-25 (Design mix) and all as shown in Electrical Plate No. 3 of MES Schedule (Part-I) of 2009 complete all as specified and directed. Notes : (i) Outer edge of earth pit will be 1 m away from the outer edge of PCC chamber. (ii) Water pipe shall be provided in slanting position.

Supply and fixing battery system dry type, maintenance free 12 volt 65 Ah for 5 KW UPS installed at OT 159 GH complete all as specified and directed Make : Su-Kam/ Amaron/ Exide

Supply and fixing UPS of capacity 5 KVA for automatic operation, single phase with, maintenance free 24 volts, 65 Ah each & designed for input variation between 100-285 volts alongwith plastic container complete all as specified and directed Make : Microtek/ Luminous/ Su-Kam

EXTERNAL WATER SUPPLY WORKS

Material and labour for construction of brick masonry valve pit of size 900 x 900 x 900mm (internal size) with mild steel sheet cover 6mm thick and frame of angle iron of size 40x40x 6mm duly painted with two coats of synthetic enamel paint over a coat of red oxide primer including excavation and earth work,150mm thick PCC (1:4:8) type D-2 as in foundation,brick work in cement mortar (1:6), locking arrangement, and all inner size of pit shall be plastered 15mm thick in cement mortar (1:4) and coping in PCC (1:2:4) type B-1 over brick wall complete all as shown in Drg No CEJZ/TD-1060/08 Sh 1/3 to 3/3.

Material and labour for construction of brick masonry valve pit of size 600 x 600 x 600mm (internal size) with mild steel sheet cover 6mm thick and frame of angle iron of size 40x40x 6mm duly painted with two coats of synthetic enamel paint over a coat of red oxide primer including excavation and earth work,150mm thick PCC (1:4:8) type D-2 as in foundation,brick work in cement mortar (1:6), locking arrangement, and all inner size of pit shall be plastered 15mm thick in cement mortar (1:4) and coping in PCC (1:2:4) type B-1 over brick wall complete all as shown in Drg No CEJZ/TD-1060/08 Sh 1/3 to 3/3.

Material and labour for cutting and jointing the existing pipe line 150mm dia for making branch connection of GI pipe of suitable and making thread for suitable insertion of tee of size 150 x 150 x 80mm complete all as specified and directed.

SUMMER APPLIANCES WORKS

Supply and fixing voltage stabilizer for automatic operation,single phase naturally air cooled indoor type with copper wound, designed for input voltage between 60 volts to 280 volts with output voltage stabilized at 230 volt with accuracy of + 2.5% and of capacity 2 KVA with low and high voltage cut off for 2 to 3 minute time dealy relay complete all as specified and directed.

Supply and fixing refrigerator, single door, electric driven single phase 230 volts, 50 Hz 192 ltr capacity, 3 star rated, frost free and testing including provision of PVC mounting stand for refrigerator including all accessories complete all as specified and directed.

LIFT WORKS

Material & labour earthing complete with galvanized steel earth plate electrode 60cm x 60cm x 6mm thick buried directly in ground vertically to a depth not less than 2.25 metre below ground level with top edge of the earth plate at a depth not less than 1.5 metre below ground level, earth plate surrounded by 15cm thick and packed with layers of charcoal dust and common salt, earth electrode GI strip 32 x 6mm connected to GI earth plate electrode by means of bolts, nuts, check nuts and washers of galvanized iron and thimbles and other end of earth strip connected to test point and protected by galvanized iron light grade 40mm bore and GI pipe 20mm bore medium grade with funnel and wire mesh for watering including necessary excavation and earth works. PCC chamber in cement concrete (1:3:6) type C-2 using graded stone aggregate and RCC cover in M-25 (Design mix) and all as shown in Electrical Plate No. 3 of MES Schedule (Part-I) of 2009 complete all as specified and directed. Notes : (i) Outer edge of earth pit will be 1 m away from the outer edge of PCC chamber. (ii) Water pipe shall be provided in slanting position.

FIRE FIGHTING WORKS

Supply and fixing inbuilt fire hose cabinet 900 x 1000 x 415mm size, made out of MS sheet 16 SWG, double door, fixed near hydrant post complete including following iterms :- (i) Cotton synthetic fibre circular woven jacket rubberized fibre reinforced rubber line hose 63mm dia 30m long with GM female coupling-02 Nos (ii) Fireman's axe with heavy duty insulated rubber handle-01 No (iii) Standard size gun metal branch pipe with GM nozzle 15mm bore outlet-01 Set (iv) Fire extinguisher dry chemical powder (ABC) type 5 Kg-01 No (v) Fire extinguisher water CO2 type 9 ltrs capacity-02 Nos (vi) Fire extinguisher CO2 type 5 Kg capacity-01 No (vii) Space to house landing valve-01 No (viii) Hose reel as per IS-3844 of standard size of 63mm dia and 30m length

Supply and fixing inbuilt fire hose cabinet 900 x 1000 x 715mm size, made out of MS sheet 16 SWG, double door, fixed near hydrant post complete including following iterms :- (i) Cotton synthetic fibre circular woven jacket rubberized fibre reinforced rubber line hose 63mm dia 30m long with GM female coupling-02 Nos (ii) Fireman's axe with heavy duty insulated rubber handle-01 No (iii) Standard size gun metal branch pipe with GM nozzle 15mm bore outlet-01 Set (iv) Space to house landing valve-01 No (v) Hose reel as per IS-3844 of standard size of 63mm dia and 30m length

Supply, installation, testing & commissioning of zonal indicator panel of upto 6 zone, having provision of audio/ video indications for FIRE, FAULT, OPEN. SHORT EARTH CIRCUIT duly interfaced with main control panel complete all as specified and directed

Supply, installation, testing & commissioning of microprocessor based main control (Fire alarm main control panel) of upto 10 zones with battery charging circuit and power supply unit having provision of audio/ video indications for FIRE, FAULT, OPEN. SHORT EARTH CIRCUIT duly interfaced with main control panel complete all as specified and directed

Supply, installation, testing & commissioning of repeater panel having provision of audio/ video (Alpha numeric multi 300) for FIRE, FAULT, OPEN. SHORT EARTH CIRCUIT duly interfaced with main control panel complete all as specified and directed

Supply, installation, testing & commissioning of response indicators made from 1.6mm thick CRCA sheet having dual red LED indication & provision for cable wire entry from top complete all as specified and directed

Supply, installation, testing & commissioning of remote response indicators made from 1.6mm thick CRCA sheet having dual red LED indication & provision for cable wire entry from top complete all as specified and directed

Supply, installation, testing & commissioning of manual call box (Pill box) made from 1.6mm thick CRCA sheet having single LED indication & release type push button in case of FIRE BREAK GLASS printed on front cover & having hammer & chain complete all as specified and directed

Supply, installation, testing & commissioning of medium intensity electronic hooter (Siren) cum speaker made from 1.6mm thick CRCA sheet with circuit having an out put of 80 DB & painted FIRE ALARM complete all as specified and directed

Supply, installation, testing & commissioning of centrifugal type bi-directional horizontally mounted Siren of 3.0 Km range operational on single phase 230 volts complete all as specified and directed

Supply and drawing of PVC insulated FRLS, 2 x 1.5 Sqm as per PS conductor copper wire into and including PVC conduit heavy duty (ISI marked) including fittings and accessories conforming to IS-694 and ISI marked cable complete all as specified and directed

Supply and drawing of PVC insulated FRLS, 2 x 4 Sqm copper conductor in and including PVC conduit heavy duty (ISI marked) including fittings and accessories conforming to IS-694 and ISI marked cable complete all as specified and directed

Supply and fixing trolley mounted type fire extinguishers of following type complee with high pressure flexible type of house copupted with discharge horn or nozzle as per the manufacturer specification :- (a) Fire extinuishers mechanical foam type 50 Ltr capacity (IS : 13386)-01 No (b) Fire extinguishers dry chemical powder type 50 Ltr capacity (IS : 10658)-01 No (c) Fire extinguishers CO2 type 22.5 Kg capacity-01 No

Supply and fixing fire extinguishers of wall mounted type with complete arrangement :- (a) Fire extinguishers dry chemical powder (ABC) type 5 Kg capacity-01 No

Supply and fixing fire extinguishers of wall mounted type with complete arrangement :- (a) Fire extinguishers CO2 type 3 Kg capacity-01 No

Supply and fixing fire hydrant stand post 80mm dia GI/MS both flanged type 1.5m height with provision of single outlet complete all as specified and directed.

CENTRAL AIR CONDITIONING PLANT WORKS (SCH 'A' PART-XVIII)

Scope of Supply (a) Microprocessor based automatic controlled with thermostat semi-hermetically sealed scroll compressor complete with automatic capacity control, safety switches forced feed lubricating system, auto restart-after power failure, built in time delay, in built thermal protection to meet automatic step capacity control of 25%, 50%, 75% and 100% full load of heat load/ design condition including first charge of compressor oil - 1 Set. Make : Danfoss/ Copeland/ Manurope/ Dunham Bush/Blue Star/Carrier/Trane (b) Shell and tube type condenser with MS shell and integrally fined copper tubing complete with safety valves drains valves, water inlet and outlet valves, hot gas inlet and liquid outlet isolating valves, thermostat and pressure gauge at inlet and outlet. - 01 set. Make : Voltas/ Blue Star/ Carrier/Trane (c) Shell and tube type direct expansion chiller unit having plane copper tubes - 01 No. Make : Voltas/ Blue Star/ Carrier/Trane (d) Refrigerant piping fittings, valves and accessories to interconnect compressor, condenser chiller and expansion valve - 01 Lot (e) (1)Microprocessor based panel comprising of following :- (i) Automatic capacity control including energy conservation. (ii) Microprocessor controlled pump down system (iii) Microprocessor based sequence of starting/ stopping of equipment with fixed time delays. (iv) Alarm history giving cause of tripping (v) Data scanner system including operating instruction (vi) Power loss trip and shut down (vii) Oil pressure failure output LP/ HP cut oil (2) Fail safe features comprising of following :- (i) Under voltage protection (ii) Single phase protection (iii) Over load protection (iv) Phase imbalance protection (v) Anti freeze protection. (vi) Refrigerant line accessories comprising of safety valves, angle valve, liquid line indicators - 01 lot (vii) Water flow switches at inlet and outlet of chiller, water drain and air purge valves where required - 01 lot

(viii) Suction line and chiller insulation with minimum 19 mm thick polyvinyl nitrite rubber insulation complete as required - 01 lot (ix) Frame work for mounting the above condenser, chiller compressor and motor with base plate complete with anti vibration pads/springs - 01 lot (x) Initial/first change of refrigerant gas and compressor oil - 01 lot (xi) Chilled water flow meter of suitable size and capacity - 01 No (xii) Reinforced cement concrete foundation including set of anti vibration pad (all as per direction of GE) for the chiller unit - 01 lot (2 working and 1 standby) (ii) Chilled water pump set Supply, erection testing and commissioning of central monoblock type chilled water pump set with bronze impeller mechanically seal of suitable discharge and head each comprising of the following and complete as per specifications. (a) Monoblock type pump set TEFC Squirrel cage induction motor of suitable HP with class 'F' insulation 2900 rpm synchronous speed, operating on 415 +\- 10% volts, 3 phase 50 Hz AC supply - 03 Nos (02 working & 01 standby) (b) Stem type thermometer at suction and delivery - 01 lot (c) 100 mm dia dial type pressure gauges with siphon & cock at both suction and delivery - 01 lot (d) Mounting frame with anti vibration pads - 01 lot (e) Reinforced cement concrete foundation (as per direction of GE) for the pump unit - 02 lot (2 working and 1 standby) (f) Water flow switches at chiller pipe lines - 06 Nos.

(iii) Condenser water pump Supply, erection testing and commissioning of central monoblock condenser water pump set with bronze impeller mechanically seal of suitable dischage and head comprising of the following and complete as per specifications. (a) Monoblock type pump set TEFC Squirrel cage induction motor of suitable HP with class 'F' insulation 2900 RPM synchronous speed, operating on 415 +\- 10% volts, 3 phase 50 Hz AC supply - 02 Nos (01 working & 01 standby) (b) Stem type thermometer at suction and delivery - 01 lot (c) 100 mm dia dial type pressure gauges with siphon & cock at both suction and delivery - 01 lot (d) Mounting frame with anti vibration pads - 01 lot (e) RCC cement concrete foundation (as per direction of GE) for the pump unit - 01 lot (2 working and 1 standby)

(iv) Under deck nitrile open cell insulation (with three Nos or as required as per design) Under deck nitrile open cell insulation shall be carried out in the AHU rooms. The specification for under deck nitrile open cell insulation shall be "Fire Retardant PE closed cell of thickness 18 mm with metalised polyester film and self adhesive backings with protection peel off paper" quantity as required. Make:- SPINTEX/UPTW/GA/BEARD SHELL/FGP/LLOYD/K flex/Armacell

(v) Air Handling Units Supply, installations, testing and commissioning of double skin floor mounted VFM type air handling units decorative type fabricated & assembled complete, made of 21 to 25 mm thick panels consisting of GI casing of thickness 0.6 mm outside layer and 0.6 mm inside layer, injected at factory by moulding machine with CFC free polyurethane foam (PUF) insulation of 42 Kg/cum complete with blower section and pre-filter section with prefilter of 10 micron of 90% efficiency, chilled water coil constructed out of copper tubes not less than 0.5 mm thick and aluminium fins, TEFC drive squirrel cage induction motor 415+/- 10% volts, centrifugal DIDW forward/backward curved fan, access door, drain pan insulated with 13 mm thick nitrile rubber etc complete as per std specifications. Maximum face velocity across the coil shall be 50 RPM and each 4 row deep cooling coil AHRI certified and RH to be maintained at 55%+/-5% the other accessories are view port, limit switches of the following capacity and comprising of :- (a) UV protection including sensors (b) Thermometer & temperature guages (c) Pre filter (MERV 6) in supply air stream (d) Energy efficient (EFF-2) squirrel cage induction motors suitable for 415+/-10% volts, 50Hz, AC supply meeting criteria as per ASHRAE standard 90.1- 2007 and high efficiency (e) 3 way balancing valves with actuator of sizes as required for satisfactory completion of work-quantity as required

(f) Humistat of suitable capacity as required for satisfactory completion of work quantity as required. (g) Ball valves of size as required for satisfactory completion of work quantity as required. (h) Heaters for de-humidification for suitable capacity to serve as monsoon re-heaters to meet the inside design condition and connected with control cable up to LT panels/Chiller unit. UVC emitters & fixtures in sufficient quantity so as to provided with distribution of UVC energy on the coil and in the drain pan. (j) Pan type humidification installed in AHU room and PVC tank 100 Ltrs capacity to be interlocked with chiller control panel by control cables and with AHU by suitable size GI tubing of required length- 01 Set (k) Fan belt drive package (l) Vibration isolator (m) Fan outlet velocity not exceeding 10 mps

(vi) Cooling tower Supply installation testing and commissioning of FRP cooling tower of 156 TR heat rejection capacity with FRP water basin PVC fitting with integral louvers and drift eliminators complete with hot water basin either fitted with spray nozzles or having self rotating sprinklers, statically & dynamically balanced axial flow type fan direct driven or driven through reduction gear box with TEFC induction motor, suction screen make up quick fitting arrangement over flow and drain connections with necessary valves and suitable inspection ladder, access arrangement for cooling tower interior, installed on MS girders (MS-I sections) fixed in masonary foundations with cement concrete footing, second class brick work and cement mortar 1:6 all accessories, basin fittings, fan, fan motor, suitable for 415 volts supporting structure, anti vibration mountings etc complete (including suitable size storage water tank) and 50 Hz power supply having isolator panel with MCB at cooling tower and with following technical data:- (a) Water flow/tower - As per design b) Ent water temp 97 deg F (c) Basin water temp 90 deg F

(vii) Piping - Chilled water Supply laying/fixing testing and commissioning the following nominal sizes of chilled plumbing pipes MS 'C' class as per IS 1239 inside the building (with necessary clamps, vibration isolators and fitting like valves, flanges union etc but excluding valves, strainer guages etc) cut to required lengths and welded at joints and inclusive of accessories like elbows, tees, reducers socket etc including insulating with 25 mm (for all pipes) and 13 mm (for drain pipe) thick closed cell chemically across linked fire retardant polyethylene foam insulation of density 30 Kg/cum. The thermal conductivity of the material should not exceed 0.035W/Mk at an average temp of 40 deg C, covered with aluminium faced foil complete with application with rubber based adhesive pidilite SR 998 and 50 mm x 3 mm thick self adhesive tape on both longitudinal & traverse joints simultaneously all as specified:- (a) 150 mm dia MS pipes (b) 100 mm dia MS pipes (c) 80 mm dia MS pipes (d) 50 mm dia MS pipes (e) 40 mm dia MS pipes (f) 25 mm dia MS pipes

(viii) Supply laying/fixing testing and commissioning the following nominal sizes of chilled plumbing pipes MS class 'C' as per IS 1239 inside the building (with necessary clamps, vibration isolators and fitting like valves, flanges union etc but excluding valves, strainer guages etc) cut to required lengths and welded at joints and inclusive of accessories like elbows, tees, reducers socket etc including insulating with 25 mm (for all pipes) and 13 mm (for drain pipe) thick closed cell chemically across linked fire retardant polyethylene foam insulation of density 30 Kg/cum. The thermal conductivity of the material should not exceed 0.035W/Mk at an average temp of 40 deg C, covered with aluminium faced foil complete with application with rubber based adhesive pidilite SR 998 and 50 mm x 3 mm thick self adhesive tape on both longitudinal & traverse joints simultaneously all as specified:- (a) 100 mm dia MS pipes (ix) Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top), double layered, 500 litres capacity, hoisted and fixed in position and totally insulated with 50 mm thick fibre glass wool density 48 Kg/Cum, covered with polythene sheet faced hessian cloth, GI chicken wire mesh and protected with 28 gauge aluminium foil cladding all as specified in SSR Part-I, complete including suitable size float valve, overflow vent, drain vent etc. all as specified and directed - 01 No.

(x) Valves, Strainers, Gauges Supply, installation, testing and commissioning of suitable size/types of valves viz, Non- return valves, Butterfly valves, Check valves, Y-Strainers and gauges in condenser water and chilled water plumbing and adequately supported as per specifications - 01 lot

(xii) Cables, Trays, Rubber Mat (a) Supplying, laying, jointing and testing under ground XLPE armoured cable insulated and PVC sheathed LT 1100 volt grade (heavy duty) with stranded aluminium conductor for following sizes laid in trenches/on floor/in duct, through pipes etc complete:- (i) 70 Sqmm 3.5 core - Quantity as required to complete the work. (ii) 50 Sqmm 3.5 core - Quantity as required to complete the work. (iii) 35 Sqmm 3.5 core - Quantity as required to complete the work. (iv) 25 Sqmm 4 core - Quantity as required to complete the work. (v) 10 Sqmm 2 core - Quantity as required to complete the work. (b) Supply, fabricating, erecting of ladder type GI cable tray 250 mm dia with box channels for supporting cable tray and with all standard accessories etc, complete all as specified and directed - 01 lot (c) Supply, fabricating, erecting of ladder type GI cable tray 75 mm dia with box channels for supporting cable tray and with all standard accessories etc, complete all as specified and directed - 01 lot (d) Control wiring with copper conductor, PVC insulated, unsheathed multi stranded, 1100V grade, single core of size 1.5 Sqmm drawn in and including PVC conduit of suitable size for interlocking arrangement as per standard practice for thermostat, humidistat, three way valve, heater bank etc required for satisfactory completion of the job complete. (e) Rubber mat 12mm thick, ISI marked, LT 1100V grade of size 0.9x1.8 mts - 03 Nos

(xiii) LT Panel and Earthing a) Supply, installation, commissioning and testing of 01 No x LT indoor type panel board factory made of approved CPRI not less than 150cmx100cmx50cm mounted indoor made out of CRCA sheet 2 mm thick dust proof, powder coated from both side, individual door, factory locking system with two side ventilation suitable for working on 415 volt AC supply including bus bar chamber and copper bus bar of capacity 400 Amp rating for phase and neutral mounted on hygroscopic insulator fixed in a separate bus bar chamber separate compartment for incoming and outgoing feeder prewired with suitable size of copper conductor cable including fitted on 50x50x6 mm angle iron channel with PCC foundation and provision of lugs and bushing for housing the following:- (i) MCCB 500 Amps TPN with shunt trip facility & overcurrent, short circuit, earth fault relays shall be provided with shunt trip (220VAC)-01 Set (incoming) (ii) MCCB 100 Amps TPN with star delta starter, push buttons, LED indicators, Multi function meter -03 Sets (Incoming to water Cooled chiller unit) (iii) MCCB 63 Amps TPN with star delta starter, push buttons, LED indicators, Multi function meter suitable for chiller pump and AHU - 05 sets (outgoing) (iv) MCCB 63 Amps TPN with star delta starter, push button, LED indicators, multi function meter suitable for condenser pump (1W&1S) - 02 sets (Outgoing)

(v) MCCB 63 Amps TPN with star delta starter, push buttons, LED indicators, Multi function meter, suitable for cooling tower motor - 01 Sets (Outgoing) (vi) MCCB 63 Amps TPN, 415V, 50 Hz AC connected with suitable phase bus bar, neutral bar and earth bus bars - 01 Set (for pre and re-heater bank) (vii) MCCB 63 Amps TPN as spare with suitable phase bus bar, neutral bar and earth bus bars - 02 Set (Outgoing) b) M&L for earthing complete with galvanized steel earth plate electrode 600x60x6mm thick, buried directly in ground (earth pit not less than 2.25 mtr deep below ground level) with top edge of the plate not less 1.5 mtr deep below normal ground level connected to GI earth strip size 25x4 mm as earth lead connected to earth plate by means of nut, bolts, check, nut & washer of galvanized iron or of steel, watering pipe 20 mm dia GI 'light grade' GI wire meshed funnel, alternate layer of char coal and salt on all side to earth plate of thickness of 150 mm filling of black cotton soil in earth pit upto ground level, PCC chamber recessed for and including RCC cover including all necessary excavation & earth work, earth wire connected to main switch board, testing the earthing after completion all as specified and shown in electric plate No. 3 of MES SSR Part - I and as directed. Set of 10 Nos

Note : (i) Details of items/ tonnage of AC plant as given above are only indicative/ tentative, vender shall ensure proper design of AC plant duly approved by IIT/ NIT as per latest engineer practice based on buildings drawings (showing air conditioned space) and include all accessories essentially required (ii) Design of AC plant with complete heat load calculation/ ducting/ AHU/ other details duly approved by IIT/NIT shall be submitted for approval of Accepting Officer not later than one month of acceptance of contract (iii) Capacity of AC plant may vary as per actual design. (iv) The Specifications given above are for broad reference purpose only. The contractor shall design the air conditioning as per best/latest engineering practice/ conforming to latest relevant IS

OXYGEN MANIFOLD WORKS (SCH 'A' PART-XIX)

(A) Oxygen Manifold 4+4 The oxygen manifold would be of above size of bulk oxygen cylinders. It is suitable to with stand a pressure of 2400 PSI. The main frame are made out of 50 X 50 X 6 mm angle iron and bottom frame of 20 X 20 mm ms square are install in such a way that the cylinders must be stage for use in upright position and are not fell down under any circumstances.The gases passed through inter-connecting tail pipes duly fitted with suitable bull nose and nut adopter for cylinder valve and tube size is 10 mm OD Copper tube duly annealed having wall thickness 1.5 mm in spiral shape and the other end of the tail pipe are fixed with non-return valve.The non return valve are fixed in brass block of size 25 mm square vertically which are fitted with high pressure copper tube of size 15mm OD having wall thickness 1.5 mm. Both the arms of manifold further fixed in automatic control panel.All the joints of copper tube, brass block, and inter connecting tubes are welded with silver brazing. Pressure release safety valve also provided. The manifold is fabricated in such a way to give distribution flow of 1500 ltrs per minute. The manifold would be degreased and purged with inert gas before commissioning. The manifold would be enamel painted as per color code. All above work would be done strictly as per specification and entire satisfaction of Engineer in-Charge.

(B) *Oxygen Emergency Point : SPECIFICATION:- In case of emergency, the supply of medical oxygen is restored immediately with this system. The emergency system would be consists of 1 no. Cylinders - configuration This would be suitable withstand a pressure of 2400psi. This would be inter connected with high pressure, high flow, double stage control regulator duly fitted with cylinder contents as well as line pressure gauges of 50mm dial size. Pressure release Safety valve are also be provided in this system, so that it would release the pressure beyond 70psi. The outlet point of pressure regulator would be connected with emergency point of oxygen pipeline with the help of inter-connecting adopters

(C). OXYGEN CONTROL PANEL (Automatic Control Panel) SPECIFICATION:The control panel would be supplied as a pre-tested and pr-sated self-contained unit The control panel is installed in the middle of both arms of manifold and fabricated in such a way that it would withstand of working pressure 2400psi and test pressure would be 3500psi. It would also supply a flow of 1500 ltrs. Per minute at a pressure of 4 bar (60psi) constantly on either bank. FEATURES • Electric audio-visual indicators for each bank status. • Electrically audio-visual indicators at the time of changeover. • Impact and weather resistance colored cover. • Independent gauges and indicators. • Automatic change over from on line bank to reserve bank and vise versa. • In built low-pressure audiovisual alarm.

Nitrous Oxide Base Unit : deatails as per oxygen (A) 1+1 MANIFOLD WITH SEMI AUTOMATIC CONTROL PANAL AND 1 CYL Emergency system

Medical Compressed Air Base UNIT The compressed air system are installed by installation of 01 number air-cooled, splash lubricated and skid mounted reciprocating type compressor. Capacity to produce 1000 liters approximately free air delivery at maximum pressure of 90 PSI.It would be fitted with 5 hp capacity induction electric motor of class F insulation It will be pre fitted with slide rails.The compressor would be installed duly fitted with suction filters, after coolers with moisture separator.The moisture separator and after coolers duly fitted with electrically operated auto drain traps will also be provided before air receiver.This system would also have one number vertical MS air receiver as per IS 226 with construction code IS 2825 of 500 ltr WC duly fitted with safety valves, drain valves, pressure gauges etc. An automatic twin chamber heatless air drier would also be installed to dry 35 CFM compressed air at 90-psi pressure at a temperature of 0-40 degree centigrade. Outlet dew point temperature would be –40 degree centigrade.The dryer would be automatic duly fitted with pneumatic operated valve, set of filters, pre-filter, oil filter and duly fitted with pressure gauges for test the filter’s condition. This system would also be fitted with bypass airline, safety valve for pressure release and pressure indicators. * TECHNICAL SPECIFICATION : AIR COMPRESSOR:(1 nos) 1.TYPE reciprocating 2.Lubrication Splash Lubricated 3.Air delivery as per requirement 4.Working Pressure 60 psi 5.Higher discharge 90-psi 6.Driver Coupling 7.Performance test As per IS 5456 8.Stages 1 9.Mounting Skid (In case skid mounted) 10.Cooling Air cooling 11.Compressor speed 2880 RPM

ELECTRIC MOTOR: 1.Capacity 5 hp 2.Round per minute 2880 3.Volts 415 4.Phase 3 5.Electric supply 50 Hz. 6.Performance test as per IS 325 7.Starter direct on lin 8.Insulation Class F Air Receiver: 1.Construction IS2825 2.Capacity 500(single) ltrs 3.Foundation skid 4.Blast cap. 300psi 5.Fittings Pressure gauge Safety valve, Drain trap, Inspection window Air Drier:- *INLET CONDITIONS 1. Flow Rate 30cfm 2. Pressure 60psi 3. Temperature 40 oc Max 4. Moisture Contents 100%rh’

Medical Vacuum Base unit As per specifications. The vacuum system is installed by providing 1 nos. vacuum pumps of reputed make of single stage , 2 cylinders. These pumps are stationary, air-cooled; splash lubricated, base plate mounted reciprocating type.These pumps would fitted on base plate and belts would be guarded. Thewould company also provide 1 no. vaccum tank of suitable water capacity as per IS 225 and construction code as per IS 2825 with all its accessories like vacuum gauge, drain valve, inspection window etc.The company will provide interconnection copper piping of size 12mm 0.0 to 28mm OD with BSP vertical non return valve of required size with vacuum gauge of required size of bottom connection with silencer and vacuums filters and all other work to complete the vacuum system and as per the entire satisfaction of Hospitals authority. The capacity of the pump would be about 35 cfm per minute vacuum at 684mm (HB). TECHNICAL SPECIFICATION : VACCUM PUMP : (1 NOS.) 1. No. Of Cylinders 2 2. Lubrication Splash 3. Vacuum/ Suction 30 cfm 4. Vacuum 684mm (HB)(MAX.) 5. Driver Electric Motor 6. Performance test International Standard 7. Stages 2 8. Mounting Skid mounted Vertical 9. Cooling Air-cooled 10. Vacuum speed 600 RPM

ELECTRIC MOTOR : 1. Capacity 5 H.P 2. Rounds per minute 1440 3. Volts 415 4. Phase 3 5. Electric Supply 50 Hz. 6. Performance test International Standard 7. Starter Star Delta direct on line 8. Insulation Class F VACCUM RECEIVER : 1. Construction IS 2825 2. Capacity 500ltr (appox.) 3. Foundation Skid 4. Blast Cap. 300psi 5. Fittings Pressure Gauge ,Safety Valve , Drain trap Inspection Window

Electrical Control Panels for above: The central electrical control panel is provided with all its accessories and caballing etc. It have separate chamber for all the starters for electric motors separately. The entire tripping device for safety of compressor, vacuum pump, manifolds are provided. Voltmeters, amp. Meters, running hrs. Meter, on/off indicators for each installation / motor would be provided separately including main circuit breakers and area circuit breakers. It would be capable to handle the total load of 55 kw installations. It would meet out the requirement of international standard as well as Indian Standard. All the fitting used in this system would be of reputed make like Crompton, L&T, and Siemens. The input volts would be 440/50Hz/3 phase and output 415 for motors and 240 for electrical. It would be off cascade type.

Copper Pipe : 12mm dia copper tube of soiled drawn seamless deoxidized, non-arsenical, half hard, tempered and degreased as per BS EN 13348:2001 duly supported with manufacturer test certificates for physical properties and chemical composition.

All as per Srl Item No. 12.08 above but 15mm dia copper tube

All as per Srl Item No. 12.08 above but 22mm dia copper tube

All as per Srl Item No. 12.08 above but 28mm dia copper tube

GASTERMINAL UNIT FOR OXYGEN : Terminal Units (Gas Outlets) with adaptors/probe for oxygen, compressed air and vacuum: Matching adaptors to the gas outlet mentioned above i.e. adaptor for oxygen, air and vacuum. The terminal units would have following features. a. It would be front insertion type. b. Terminal unit would have mechanism with check valve. C. Allow single hand operation. D. On first insertion of probe the probe shall sit in a standby position. At the stage there shall be no gas flow. E. Only on pressing the probe second time, the gas supply would start. F. They would close automatically when connected apparatus is removed. G. For allowing on line maintenance the terminal unit would be equipped with a check valve for all positive pressure gases for closing gas supply whenever the outlet point is opened. H. The outlet would be non interchangeable for specific gas and it would accept only correct medical gas adopter/Probe. I. It would be color coded as per HTM 2022 J. The design of this outlet would be compatible to installed vertical on valve horizontally on ICCU panel and area servicing unit and also vertical to fit in pendants. K. It would only supply with correct probe/ adopter.

All as per Srl Item No. 12.12 above but for nitrous oxide

All as per Srl Item No. 12.12 above but for medical air 4 BAR

All as per Srl Item No. 12.12 above but for vacuum

ISOLATION VALVES ASSEMBLY: CE MARKED ISO 9001-2008 SPECIFICATION: To control the pressure as well as for maintenance quarter turn open at 90-degree ball type valves would be provided. These valves would be of nickel-plated brass body having PTFE seat and inner outer seals. These valves would have stainless steel ball of specific ID clearance so that line pressure would not drop. For installation only PTFE gaskets would be used in between nuts and valve to prevent leakage.All the nuts for fixing the ball valve would be of brass with brass nozzles for easily brazing with copper tube. All ball valve assemblies would be on approachable height for easily operation. And enclosed in powder quoted visible box. TECHNICAL SPECIFICATION 1. Leakage Clause : 1 2. Temperature range : Ambient 3. Working Pressure : 7.5 bar maximum 4. Test pressure : 50 bar maximum 5. Standard : As per HTM 2022 6. Size : 15mm to 28 mm

It would also have color code around the specific gas outlet and a slide rail for focus lamp. It would be polyester powder coating finish on all external surfaces and would be fitted with wall with the help of 8mm fasters at specific It would be fixed in such a manner that it could be remove easily for servicing and repair. It would be long and continuous to fix for any distance Following fixed Accessories on Pendant: 1. Four 5 Amp. Sockets ,2. Two 15 Amp sockets, 3. Two I.V Hooks , 4. Moveable trays for equipments/ Monitors, 5 Color bin, 6. Telephone Port, 7. Data Transfer Port . Facility to fix Following Accessories Pendant: 1. Facility to hose One Oxygen Outlets, 2. Facility to hose One Vacuum Outlets, 3. Facility to hose One compressed air Outlets ,4. Facility to hose One Nitrous Oxide Outlets

Bed Head Unit(4' LONG) CE MARKED AS PER HTM 2022 : The modular medical turn king system/bed head panel: would be fabricated of aluminous die pressed 1.6 mm thick imported laminated sheet in such a way to provide 100% safe and efficient means to deliver all the gases as well as electrical to the patient/staff in intensive care conditions. To enclosed all piping, electrical wires, monitor wire ect it would be fitted 4feet long on wall .The design of modular BHU would consist of aluminum section to meet the requirement of HTM 2002, NFPA and other international standard.It would have separate duct for medical gases as well as electrical. There would be no sharp edges having smooth finish and without any visible Reciprocatings etc.It would be have ability fix medical gas outlets, electrical sockets, multi channel music system, nurse’s call bell, IV fluid’s saline and space for placement of monitors. It would also have color code around the specific gas outlet and a slide rail for focus lamp. It would be polyester powder coating finish on all external surfaces and would be fitted with wall with the help of 8mm fasters at specific It would be fixed in such a manner that it could be remove easily for servicing and repair. It would be long and continuous to fix for any distance Following fixed Accessories on Pendant: 1. Four 5 Amp. Sockets ,2. Two 15 Amp sockets, 3. Two I.V Hooks , 4. Moveable trays for equipments/ Monitors, 5 Color bin, 6. Telephone Port, 7. Data Transfer Port . Facility to fix Following Accessories Pendant: 1. Facility to hose One Oxygen Outlets, 2. Facility to hose One Vacuum Outlets, 3. Facility to hose One compressed air Outlets ,4. Facility to hose One Nitrous Oxide Outlets

OT SUCTION TROLLEY of Cpacity 4000 ml. CE MARKED

BPC Flowmeter with humidifier bottle CE MARKED- would be BPC single type Pipeline Flow Meter unit duly fitted with the fine adjustment valve. It would be backpressure compensated to bear and control the Oxygen Pressure approx. 60psi. Flow meter unit would be consisting of double wall rotta-meter has range of flow 0 to 13 ltrs. per minute with fine adjustment valve. The rotta meter and humidifier bottle would be made of clear, impact resistance polycarbonate (duly graduated). This unit would be have attachment to fit humidifier bottle of capacity 100 Ml. consist of clear, impact resistance polycarbonate jar. This would also have Reciprocating on top for flow meter/plastic cap having nozzles for outlet tubes and the inlet tube end would be multi function combination bubblier/ nebulizer to add the humidity and create an aerosol in Medical Gas min marks would be on jar. This unit would be supplied with PVC Clear green tube of 1.5mtrs. Long duly fitted with disposable Oxygen mask

Supply, fixing, testing and commissioning of central valve for pressure control quarter turn open at 900 ball type valve, made of nickel-plated brass body having PTFE seat, stainless steel ball (to stop pressure drop) including working pressure 7.5 bar & test pressure 50 bar as per HTM 2022 of size of 12mm including PTET gaskets, nuts, brass nozzle, copper tube etc complete all as specified and directed. Make : ELEM/ JSI/ Zoloto and equivalent

All as per Srl Item No. 12.21 above but 15mm dia

All as per Srl Item No. 12.21 above but 22mm dia

All as per Srl Item No. 12.21 above but 28mm dia

Supply and fixing curtain partition (length 15') to cover max running feet and made of high quality synthetic washable, stain free cloth of size 2025mm (L) x 1300mm (W) including hooks wheel, certain tank of aluminium alloy end caps supporting brackets, roller, ring curtain ceiling support and all item which is required to fix the curtain complete all as specified and directed

Ward vacuum unit : The vacuum regulator would be fitted with vacuum gauge and it also shows flow rate.It would also have overflow safty trap.It would also have emergency on / off lever and fine adjustment valve for regulator. This system would be supplied with pre fitted color coded gauge having dial size 50mm and vacuum 0 to 760 mm / hg and supplied with all the inter connectiong tube with patient tube

MANNING AND OPERATION OF AIR CONDITIONING PLANT WORKS (SCH 'A' PART-XX)

Manning and operation of Air conditioning plant, firefighting system and DG Sets during defect liability period of 24 months from the actual date of completion including compressors, condensers, AHU Unit, cooling tower ,pipe line, pumps including operation of valves complete by providing/ deploying all required supervisory, Technical Staff and required number of Helper but minimum as following :- (i) FGM-01 No per shift for 03 shift (ii) Refrigeration mechanic - 01 No per shift for 03 Shifts (iii) Helper - 01 No per shift for 03 Shifts Notes :- (a) Quantity is variable and shall be calculated actually for 24 months period of completion as given. (b) The operator shall be ITI certificate holder from recognized board having minimum two year experience in similar Job/ trade in Refrigeration and Air Conditioning with 2 year experience in relevant field, responsible for plant operation and maintenance round the clock including Sunday and Holiday. (c) Helper to assist the refrigeration mechanic (minimum 10th pass) responsible for AC Plant/ Parts cleaning, cleaning surrounding area and carry necessary T&P from smooth functioning of plant, operation and maint around the clock including Sunday and Holiday. (d) The contractor shall submit name of persons to be deployed at work alongwith their qualifications and experience for approval from GE before the date of commencement of work. (e) Subsequently action for verification of antecedents of the persons to be deployed shall be taken by the contractor and submit the same to Engineer-in-Charge/ GE within 07 days from the date of commencement of work (f) Cleaning of area in and around pump houses & common areas (viz cutting of grass & disposal of debris) are deemed to be included in the scope of the work. Default if any noticed in duty of cleaning, recovery will be imposed as per clause specified in the Particular Specifications.

MANNING AND OPERATION OF LIFT WORKS (SCH 'A' PART-XXI)

Manning and operation of running of lifts during defect liability period of 24 months from the actual date of completion including control panel and all other items connected to the lifts complete by providing/ deploying all required supervisory, Technical Staff and required number of Helper but minimum as following :- (i) Lift Operator - 01 No per shift for 02 Shifts/Day for 02 Nos of Lift. (ii)Lift Operator - 01 No for night for 02 lift for day. Notes :- (a) Quantity is variable and shall be calculated actually for 24 months period of completion as given. (b) The operator shall be having minimum two year experience in similar Job/ trade in lift with 2 year experience in relevant field, responsible for operation and maintenance round the clock including Sunday and Holiday. (c) Responsible for lifts/ Parts cleaning, cleaning surrounding area and carry necessary T&P from smooth functioning of plant, operation and maint around the clock including Sunday and Holiday. (d) The contractor shall submit name of persons to be deployed at work alongwith their qualifications and experience for approval from GE before the date of commencement of work. (e) Subsequently action for verification of antecedents of the persons to be deployed shall be taken by the contractor and submit the same to Engineer-in-Charge/ GE within 07 days from the date of commencement of work

M/s Madan Lal Bansal and Co. Contractors Pvt. Ltd.

VIJAY JINDAL BUILDERS PVT LTD

Komal Buildcon Pvt. Ltd.

SHRI GURMUKHDAS CONTRACTORS PVT. LTD.

Rabina Enterprises Pvt Ltd

Saru Enterprises Pvt Ltd

GEMINI PROMOTERS AND BUILDERS PVT. LTD.