City Sanitation Action plan CSAPs- For used water management as per Annex 3B of SBM- U 2.0

Amount

Description

Cutting in Earth work and disposal of excavated earth upto a lead of 20 meters . Spade Work , Pick Work , & Jumper Work

Excavation in foundations, trenches etc. in earth work, lift up to 1.50 mtrs. stacking the excavated soil not more than 3 mtrs. clear from the as of excavation and then returning the excavated soil in 15 cm. layers when required into plinths sides of foundations etc., consolidating each deposited layer by ramming and watering and then disposing of all surplus excavated soil as directed within a lead of 20 mtrs.- P-J Work

Providing and laying cement concrete 1:3:6 (1 cement : 3 sand : 6 graded stone aggregate 40mm nominal size) and curing complete excluding cost of form work in:- Plinth & Foundation

Providing form work with steel plates 3.15 mm thick welded with angle iron in frames 30x30x5 mm so as to give a fair finish i/c centring ,shuttering, strutting and propping etc. with wooden battens & ballies, ht. of propping & centring below supporting floor to ceiling not exceeding 4 mtrs. & removal of the same for insitu-reinforced concrete work in :

Vertical surfaces such as walls ( any thickness ) partitions and the like including attached pilasters , buttresses, plinth and string courses and the like .

Providing Bolder/Stone filling behind R/Wall

Providing & Fixing of Weep Hole PVC 100 Dia Pipe

Providing and laying cement concrete 1:3:6 (1 cement : 3 sand : 6 graded stone aggregate 20mm nominal size) and curing complete excluding cost of form work in:- Plinth & Founadtion

Providing and laying cement concrete 1:1.5:3 ( 1 cement : 1.5 sand : 3 graded stone aggregate 20mm nominal size) and curing complete excluding cost of form work & reinforcement for reinforced concrete work in:-

Foundation and Plinth.

Walls (any thickness but not less than 0.1 m thickness) attached pilasters, buttresses, plinth and string courses etc. from top of foundation level up to floor two level.

Providing mild steel/tor Steel reinforcement for R.C.C work including bending , binding and placing in position complete up to floor two level.

Providing smooth finishing in cm 1:3

Providing and laying in trenches, D.I. Tube fittings (earth work in trenches to be measured and paid for separately).

Catchpit to Filter Sump 150 mm Dia

100 mm Dia

Providing & Laying of Filter Media in Filterate Unit

Bottom Layer 63 to 80 mm Coarse Gravel

Fine Gravel 6 to 30 mm

Fine Sand 0.50 to 0.75 mm

Providing and Fixing of C.I. Sluice valve 150 mm Dia

100 mm Dia

Providing & Fixng of Common Header for Filter Sump

Providing & Fixing of CI Foot Valve 80 mm Nominal Dia PN 6

Providing & Fixing of CI Sluice Valve 80 mm Nominal Dia PN 1.6

Providing & Fixing of NRV 80 mm Nominal Dia

Providing & Fixing of DI 90 Degree Band 80 mm PN 1.6

Providing & Fixing of Tee 80 mm

Providing & Fixing of Reducer 80 X 40 mm Dia

White Washing with lime on undecorated wall surfaces two coat to give and even shade including thoroughly brooming the surface to remove all dirt dust and other foreign matter.

Providing and laying cement concrete 1:2:4 work (1 cement : 2 sand : 4 graded stone aggregate 20 mm nominal size) and curing complete excluding cost of form work and reinforcement for reinforced concrete work in:- Plinth & Foundation

Steel Work in single section including cutting , hoisting , fixing in position and applying a priming coat of lead paint . Angle 50*50*5 mm Thick

Providing & fixing UV stabilised fiberglass reinforced plastic sheet roofing up to any pitch, including fixing with polymer coated 'J' or 'L' hooks, bolts & nuts 8mm dia. G.I plain/bitumen washers complete but excluding the cost of purlins, rafters, trusses etc. The sheets shall be manufactured out of 2400 TEX panel rovigs incorporating minimum 0.3% ultra-violet stabiliser in resin system under approximately 2400 psi and hot cured. They shall be of uniform pigmentation and thickness without air pockets and shall conform to IS 10192 and IS 12866.The sheets shall be opaque or translucent, clear or pigmented, textured or smooth as specified.2 mm thick corrugated (2.5" or 4.2" or 6") or step-down (2" or 3" or 6" ) as specified

Manufacturing and supply of Wiremesh made out of Angle Iron 50 X 50 X 5 mm & Wiremesh including taking arrangement complete including welding cutting drilling complete in all respect.

Prov. 3 Phase Slude pump set of reputed and approved make i.e. KSB model MR-3 confirming to letest BISspecifications i.e. 8304 . The pump set shall be fixed with free flow impellers of suitable allow as per BIS -8631-1976 with upto date amendmentsfor lifting raw water lubricated bush bearings of suitable alloy and shaft protection sleeves the pump shall be fitted coupled to submercible required cage motor com-pump to BIS 9283-1995 with upto date amendments corresponding to pump, fitted with water lubricated bush bearing alloys and shaft protection sleeve arrangement to counter balance the thrust caused due to water column in rising main and having cooling arrangement. The pump set should include the water level guard, errection clamps , cable clips and capable of following performances.

Static head = 10 mtrs

Discharge = 3 LPS

Dia of Rising main = 80 mm

Length = 30 mtr

Pumping hours = 8 Hour

P/F 3 core copper cable wire 6 mm Sqm (Flat Submersible Cable)

P/F control panel for 3 HP Three phase with Amp. Mete,r volt meter, stater MCB water level gurd.

Installation of Pump Set i/c Cutting , welding , Jointing ,complete in all respect at site.

Carriage of Pump Set & Other accessories.

Repair of Filter Press.

INDU KANWAR (BID ID -532636)

Kamlesh Kumar (BID ID -531382)