SPECIAL REPAIR TO TOILETS IN LIVING IN ACCN OF AIRMEN, PROVN OF CABLE TRAY FOR MAITENANCE STAND AND SEPARATE UPS WIRING FOR L2 SWITCH AT AF STN HASIMRA AND PROVN OF SPLIT TYPE AIRCONDITIONER, REFRIGRATOR AND CERTAIN E/M FITTING FIXURES AT IMTRAT ARE

Amount

Dismantling of floor, hearth or wall tiles including cement mortar bedding ( but not backing) and remvoing rubbish off the premises, complete all as specified and directed.

M&L for non skid ceramic coloured tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.06 Sqm but not exceeding 0.11 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement of match the surfaces over and including 15mm thick screed bed in CM (1:6), complete all as specified and directed.

M&L for joint free glazed ceramic coloured tiles in vertical surface 350 x 250 x 7mm/450 x 350 x 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match including 10mm thick rendering back coat in CM (1:4), complete all as specified and directed.

Demolition of reinforced cement concrete(reinforcement cut as required to facilate demolition) of any description and in any position not otherwise specifically provided for, complete all as specified and directed.

Use & waste formwork to sides and soffits of floor or roof beams, beam haunching’s, girders, breastsummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. fair finish flat surfaces of formwork, complete all as specified and directed.

S & F mild steel TMT bars 6mm to 8mm dia (Grade Fe-500D), cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9mm dia., or securing with clips, complete all as specified and directed.

M&L for RCC (nominal mix) (1:2:4) type B1 (using 20mm graded crushed stone aggregrate) as in, slab cover, beams, cantilevers, bressummers, lintels etc., complete all as specified and directed.

Demoliton of cement concrete in ground floors and pavings n. exc. 15cm thickness (below or above ground level), complete all as specified and directed.

M&L for 75mm thick PCC (1:2:4) type B- 2, (using 40mm graded crushed stone aggregate) for pavings or plinth protection etc., complete all as specified and directed.

M&L for forming 12mm thick expansion joints filled with pre-formed bituminous filler and top 30mm primed and sealed with sealing compound grade 'B', thichness of slab below 100mm, complete all as specified and directed.

Demolition of brick work or stone/boulder masonary, built in cement mortar including all quoins, arches, pillars etc but excluding ashlar facings, dressed stonework and precast concrete aritcles, complete all as specified and directed.

M&L for brick work with sub class 'B' bricks, old size, burnt clay bricks, straight or curved on plan exc 6 mtr mean radius built in CM (1:6), complete all as specified and directed.

M&L for brick work with sub class 'B' bricks, old size, burnt clay bricks, straight or curved on plan exc to any radius built in CM (1:4) in half brick thick, complete all as specified and directed.

Taking down cement plaster on brick or concrete surfaces including racking out joints, hacking for key, scrubbing down with water etc, complete all as specified and directed..

M&L for 10mm thick cement plaster on fair faces of brick work or concrete surfaces in CM (1:6) and finished even and smooth without using extra cement, complete all as specified and directed.

M&L for 15mm thick cement plaster on other than fair faces of brick work or concrete surfaces in CM (1:4) and finished even and smooth without using extra cement, complete all as specified and directed.

M&L for preparation of newly plastered wall surfaces and applying two coats of cement base paint over a coat of alkali resistant primer, complete all as specified and directed.

M&L for preparation of old surfaces of walls and applying two coats of white wash, complete all as specified and directed.

M&L for preparing newly plastered surfaces of wall and applying two coats of oil bound distemper over a coat of 2mm thick wall care putty, complete all as specified and directed.

M&L for preparation of old painted steel or iron surfaces and applying one coat of synthetic enamel paint (1st grade quality) on surface of any description over 10cm width or girth not otherwise described, complete all as specified and directed.

Taking down 15mm bore steel water tubing and connection from wall/ceiling surfaces including cleaning for refixing or removal from site of work, complete all as specified and directed.

Taking down 20mm bore steel water tubing and connection from wall/ceiling surfaces including cleaning for refixing or removal from site of work, complete all as specified and directed.

Taking down 25mm bore steel water tubing and connection from wall /ceiling surfaces including cleaning for re-fixing or removing from site of work, complete all as specified and directed.

S&F CPVC pipe of size 20mm dia, high pressure SDR 11 & plain CPVC SDR 11 fittings complete, fixed in floors/wall/ceiling with necessary saddle/clamps including all necessary fittings like elbow, tee, socket, reducer etc. with necessary solvent cement, complete all as specified and directed.

S&F CPVC pipe of size 25mm dia, high pressure SDR 11 & plain CPVC SDR 11 fittings complete, fixed in floors/wall/ceiling with necessary saddle/clamps including all necessary fittings like elbow, tee, socket, reducer etc. with necessary solvent cement, complete all as specified and directed.

S&F in repair 25mm bore gun metal globe or gate valves with iron wheel head, screwed both ends for iron pipes, complete all as specified and directed.

S&F in repair vitreous china squatting pan,"Orissa pattern" white, size 580mm x 440mm with integral foot rest, 'P' or 'S' trap, including connection to trap, and to flushing pipe, anti -syphonage pipe etc., complete all as specified and directed.

S&F in repair 10 ltrs capacity low level valve less PVC syphonic action type flushing cistern white with inlet ball valve, float and handle and connection to pipes, complete all as specified and directed.

S&F in repair CP pillar tap, 15mm bore, fancy type, cast copper alloy, capstan head, chromium plated, screwed down high pressure with or without lettered “hot’ or “cold” with long screwed shanks and fly nuts screwed for iron pipe, complete all as specified and directed.

S&F in repair 15mm bore, fancy type, chromium plated, bib tap, cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or union, complete all as specified and directed.

S&F in repair 15mm bore, fancy type, chromium plated, stop valves, with long shank and cup (concealed type) angular, cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or union, complete all as specified and directed.

S&F in repair 15mm bore, two way bib tab (fancy type), chromium plated, cast copper alloy screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or union, complete all as specified and directed.

S&F in repair 15mm bore angular vave, chromium plated, cast copper alloy, screwed down, high presure with crutch or butterfly handle screwed both ends for iron pipe or union, complete all as specified and directed.

S&F in repair swivel shower rose 125mm size, brass, chromium plated for fixing with 15mm bore pipe, complete all as specified and directed.

S&F in repair CP shower arm 15mm size, 195mm long with bend of 45 degree with flange, complete all as specified and directed.

S&F PVC connection 15mm size with PTMT nuts of length 600mm, complete all as specified and directed.

S&F of 32/40mm dia collapsible waste pipe not less than 800mm long for wash hand basin and sink, complete all as specified and directed.

S&F in repair towel rail 600mm long of PTMT fixed with and including chromium plated brass screws and wooden/plastic cleats.(Minimum weight 190gms), complete all as specified and directed.

S&F 5.5mm thick glass shelf of size 12cm wide x 60cm long for wash hand basin etc., complete all as specified and directed.

M&L 75mm dia PVC (SWR) floor trap, plain with grating including jointing with solven cement as in repairs, complete all as specified and directed.

S & F in repair 110mm bore PVC (SWR) rain water pipes,single sockets, in any length with sealant rubber ring joints laid in trenches or in floors, complete all as specified and directed.

S&F in repair of 110mm bore, PVC (SWR) bends of any radius, complete all as specified and directed.

S & F in repair 75mm bore PVC (SWR) rain water pipes, single sockets, in any length with sealant rubber ring joints laid in trenches or in floors, complete all as specified and directed.

S&F in repair of 75mm bore, PVC (SWR) bends of any radius with access door, complete all as specified and directed.

S&F in repair 75mm bore PVC (SWR) junction, single, (single T) equal or unequal, complete all as specified and directed.

S&F in repair CP grating 100mm dia fixed with white cement, complete all as specified and directed.

S&F rotational moulded polyethylene (HDPE) water storage tanks, triple layered, (cylindrical vertical with closed top) ISI marked, confirming to IS 12701-1989, hoisted and fixed in position all as specified in SSR Part I (1000 ltr capacity) including 20mm Nipple suitable for HDPE water tank and ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball, screwed for iron pipe and fixed to 20mm bore pipe inculding dismantling of old unserviceable water tank, complete all as specified and directed.

S&F in repair 25mm bore ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball, screwed for iron pipe or brass, complete all as specified and directed.

Taking down chowkats with shutter (without taking off shutter from the frame) not exc. 1.5 Sqm each., complete all as specified and directed.

Taking down chowkat with shutter (without taking off shutter from the frame) exc 1.5 Sqm but n.exc. 4 Sqm each, complete all as specified and directed.

S&F 2nd class hard wood plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, complete all as specified and directed.

Cutting holes in brick walls built in CM for inserting hold fasts and making good dismantled portion in CM (1:3) or PCC (1:2:4), type B-1 (using 12.5mm graded crused stone aggregate) as in depth of embedded portion of hold fast n. exc. half brick, complete all as specified and directed.

S&F solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, as per specification & drawings, complete all as specified and directed.

S&F factory made solid PVC moulded door shutter with wood board core free EPS, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick 3D wood grain Moulded PVC sheet polyurethane painted on the front face & 2mm prelam PVC Sheet on back face, supplying & fixing in frame at site as per specification & drawing, complete all as specified and directed.

S&F 30mm thick 2nd class hard wood glazed and skelton shutters, open rebated and prepared to receive glass, gauze etc divided into squares, with plain, chamfered or rounded, mitered and rebated sash bars, any numbers edges of framing plain, chamfered or rounded, fitted with cut and mitered beads for securing glass etc. sizes of members of shutters as specified in SSR Part-1, Section 8, clause 8.24 (a) and fitted to chowkats, complete all as specified and directed.

S&F 35mm thick 2nd class hard wood glazed and skelton shutters, open rebated and prepared to receive glass, gauze etc Sqm divided into squares, with plain, chamfered or rounded, mitered and rebated sash bars, any numbers edges of framing plain, chamfered or rounded, fitted with cut and mitered beads for securing glass etc. sizes of members of shutters as specified in SSR Part-1, Section 8, clause 8.24 (a) and fitted to chowkats, complete all as specified and directed.

S&F butt hinges of size 100mm, extruded aluminium alloy with galvanised mild steel hinge pin,anodised and fixed, type C-21, complete all as specified and directed.

S&F aluminium alloy anodised, sliding door bolt 250mm long with hasp, staple (bolt type) and fixing clips of sheets, cast extruded sections and fixing bolt and sliding bolts of extracted sections, complete all as specified and directed.

S&F 150mm long aluminium anodised, barrel tower bolt of extruded section, complete all as specified and directed.

S&F 150mm long aluminium handle, cast type anodised, complete all as specified and directed.

S&F floor door stopper of aluminium alloy body and tongue, anodised with hard drawn steel spring fixed in floor 150mm size of cover plate, complete all as specified and directed.

S&F 300mm mild steel ordinary rat tail rod pattern springs including roller and roller plate including brass brackets, complete all as specified and directed.

M&L for preparing new wooden surfaces of any description, not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint (1st grade quality) over a coat of pink primer, complete all as specified and directed.

Hacking out old broken glass any thickness size quality or description from metel frame/aluminium frame including punching or drilling our old glazing pins/spring clips, complete all as specified and directed.

S&F 4mm thick sheet glass, ordinary quality, as in doors, window, showcase in aluminium frame work & similar work exc. 0.50 Sqm in each pane including neoprene gasket, complete all as specified and directed.

S&F stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks, or galvanised wire staples, complete all as specified and directed.

S&F in repair stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks, or galvanised wire staples, complete all as specified and directed.

M&L for mild steel framed work such as grill, gratings etc with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars, barrel iron doors, ladders framed balusters, walks railings, frame work of water tanks and similar work conforming to E-165 (Fe-290), complete all as specified and directed.

M&L for preparation of new steel or iron surfaces of any description over 10cm width or girth not otherwise described and applying two coats of synthetic enamel paint (1st grade quality) over a coat of red oxide primer, complete all as specified and directed.

S&F for 605x 605mm GI frame work for seamless ceiling comprising of Gl perimeter channnel 0.55mm thick with two unequal flanges of 20 and 30mm and web of of 27mm fixed to surrounding wall using nylon sleeves and screws at 450mm centre to centre/intermediate channel 0.9mm thick having two equal flanges of 15mm each and web of 45mm suspended from soffit at approx 900mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55mm thickness having kurled web of 50mm and flange of 26mm each with lips of 10.5mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457mm centre to centre including providing 6mm thick non asbestos fibre cement building boards fixed or laid/ inserted to timber/GI/aluminium framework with screws, 60x 60cm in size, fixed with nails to timber framework or with staples on snap grid including dismantling of old unserviceable ceiling boards of any description, including cover fillets, complete all as specified and directed.

M&L for 25mm CPVC ball valves including all fittings fixed in wall/ceiling/floor, complete all as specified and directed.

Excavation in trenches not exceeding 1.5 metre wide and not exc 1.5 metre in depth for foundation of pole/stay, or cable trenches etc and getting out in soft/loose soil, complete all as specified and directed.

Returning filling in incl spreading, leveling watering and well ramming in layers not exceeding 25cm in soft/loose soil, complete all as specified and directed.

Removing excavated materials to a distance not exceeding 50 mtr and depositing where directed at a level not exceeding 1.5 metre above the starting point in any type of soil, complete all as specified and directed.

M&L for cutting CI/DI/GI pipes and reducing to required length for connection of Tee or branches of 50/80mm bore pipe, complete all as specified and directed.

Taking down carefully point wiring of any type, size and description from hard/ teak wood batten/through pipes/casing capping (light, fan, sockets and socket outlets etc) including removal of battens, pipes, plug sockets, socket outlets, switches, shades, ceiling roses, light fittings etc. complete and making good the disturbed surface to match with existing, complete all as specified and directed.

M & L for point wiring complete with PVC insulated unsheathed, 1100 volts grade cable 1.5 Sqmm (nominal area) FRLSH type multi stranded copper conductor, single core drawn in and including PVC conduit, medium grade, (ISI marked), heavy duty of adequate size including its accessories not less than 20mm dia rigid PVC conduit 'medium grade ISI marked including all conduit accessories including pressed steel terminal box of required size factory made with top cover of ISI marked plastic laminated sheet of required colour for mounting switch, sockets, fan regulator etc including 1.5 Sqmm FRLSH type PVC insulated unsheathed cable multi-stranded copper conductor as continuous earth wire and connected to earth dolly as required at site & including chases cutting & making good disturbed surface & applying finishes to match existing surface etc. for one light/fan point controlled by one, one way switch single pole, complete all as specified and directed.

All as per item No 78.00 here-in before but one 3 pin 5 Amps socket outlet on same board controlled by other switch, complete all as specified and directed.

All as per item No 78.00 here-in before but one 3 pin 5 Amps socket outlet on the independent board controlled by other swtich, complete all as specified and directed.

All as per ser item No. 78.00 here in above but for one 16 Amp 6 pin switch socket outlet independent point including PVC cable 2.5 Sqmm FRLSH type copper stranded conductor along with 2.5 Sqmm continious PVC insulated unsheathed standard copper conductor cable FRLSH type for as earth wire, complete all as specified and directed.

S&F in repair switch piano flush button, single pole, one way, 6 Amps 240 volts, complete all as specified and directed.

S&F in repair switch and socket combination, flush type, 5 pin, 6A, complete all as specified and directed.

S&F in repair switch and socket combination, flush type, 6 pin, 16A, complete all as specified and directed.

S&F in repair socket outlet, flush type, 5 pin, 6 Amp, complete all as specified and directed.

S&F exhaust fan, steel body AC, single phase, 230V of size 300mm sweep with, blades, and frame and louvers including cutting wall for fixing exahaust fan of size 300mm sweep and making good the opening in CM (1:3) or PCC (1:2:4) type B1 as required at site including taking down old exhaust fan, any size and deposited to AGE E/M store yard, completes all as specified and directed.

S&F ceiling rose of size 65 x 50mm surface bakelite 240 Volts, three terminal, complete all as specified and directed.

S&F LED lights fitting 1x 20 W, 220V, AC, box type with driver, LED lighting fixture with extruded aluminium channel, including LED tube light of 20 watt connecting up with three core flexible copper conductor cable of suitable size from ceiling rose, completes all as specified and directed.

S&F power unit suitable 25 Amp including sockets 25 Amps, and 02 module box for mounting of power unit and power socket, complete as specified and directed.

S&F in repair modular socket 16 Amp, 2 module box for mounting of power unit and power socket, complete all as specified and directed.

S&F in repair metal flush box, 2 module, mounting of power unit and power socket, complete all as specified and directed.

S&F LED light fitting mirror type with high output diffuser 2 feet, 10 watt 220 V, AC, decorative type with driver, LED tube light of 10watt connecting up with three core flexible copper conductor cable of suitable size from ceiling rose, completes all as specified and directed.

S&F sheet metal enclosure for double door MCB DBs, Single Pole & Neutral (SPN), suitable for 12 way, 415 volts, IP 43 & IK 09 with metal door fixed on wall with din rail, neutral and earth bar, fixed in proper position including taking down old unserviceable one, complete all as specified and directed.

S&F RCBO for earth leakage, over load and short - circuit protection 32 Amp DP 100 mA, completes all as specified and directed.

S&F MCB SP 6 to 32 Amps, 240V, 10 KA, 'C' curve, including connection of testing, completes all as specified and directed.

S&F MCB SPN 6 to 32 Amps, 10 KA, 'C' curve, complete all as specified and as directed.

Supply and draw sub main wiring in repairs of two run 6.0 sqmm single core (FRLSH) PVC insulated, unsheathed multistranded copper conductor cable 1100 Volt grade, drawn through and including PVC conduit (ISI marked), medium duty, of not less than 25mm size including all conduit accessories, concealed to the surfaces of the wall/ceiling including one run of 6.0 sqmm single core (FRLSH) PVC insulated unsheathed copper earth continuity including taking down existing sub-main wiring, complete all as specified and directed. Note: (i) Two runs of single core cable with one run of earth continuity conductor including PVC conduit & accessories shall be measured and paid as one length. (ii) Cutting chases shall be measured and paid separately.

Supply and draw sub main wiring in repairs of two run 4.0 sqmm single core (FRLSH) PVC insulated, unsheathed multistranded copper conductor cable 1100 Volt grade, drawn through and including PVC conduit (ISI marked), medium duty, of not less than 25mm size including all conduit accessories, concealed to the surfaces of the wall/ceiling including one run of 4.0 sqmm single core (FRLSH) PVC insulated unsheathed copper earth continuity including taking down existing sub-main wiring, complete all as specified and directed. Note: (i) Two runs of single core cable with one run of earth continuity conductor including PVC conduit & accessories shall be measured and paid as one length. (ii) Cutting chases shall be measured and paid separately.

Supply, installation, commissioning and testing of capacity 50 litres geyser to operate/function on AC 220 v, single phase having heating element 2 KW capacity and high thermal cut-out BEE approved 5 star rated including fixing of geyser in wall with required fixing material and PVC connection pipe (hot and cold type) of 600mm length and 15 Amp plug top, complete all as specified and as directed.

Fixing only exhaust fan and connecting up including provision of cable from ceiling rose/connector to fan, complete all as specified and as directed. Note : Exhaust fan shall be issued under Sch 'B' as free for fixing.

S&F in position heavy duty powder coated MS cable trunking of the sizes 300mm wide x 50mm wall height cable tray alongwith cover of cable tray (standard type C) for supporting 1100 Volts grade armored/ unarmored aluminium/copper conductor cables, fabrication from angle and perforated 2mm thick M.S CRCA sheet powder coated with expansion coupler, elbow, bend, inside outside riser, equal un-equal tee etc with suitable cover plates powder coated and suitable cover with bolts, washer and nuts, knock out holes for cable connections as per approved design, the tray shall comply with the specification of NEC (National Electric Codes) and NEMA (National Electric Manufacturers Association) the steel shall be as per IS: 226 and galvanizing as per IS: 2629BS 729IASTM 123 including taking down of existing cable of carefully and fixing the cable on cable tray, completes all as specified and directed.

S&F cable tray/bus bar fixing supports and other steel work/including MS flats, angles. T iron, channel etc. cutting drilling holes/welding in MS members as per the site requirements, duly painted the supports with two coats of synthetic enamel paint (1st grade quality) over a coat of primer, including provision of dash fasteners and other fixing accessories, completes all as specified and directed.

Supply and draw sub main wiring in repairs of two run 10.0 sqmm single core (FRLSH) PVC insulated, unsheathed multistranded copper conductor cable 1100 Volt grade, drawn through and including PVC casing caping (ISI marked), heavy duty, of suitable size including all conduit accessories, concealed to the surfaces of the wall/ceiling including one run of 10.0 sqmm single core (FRLSH) PVC insulated unsheathed copper earth continuity including taking down existing sub-main wiring, complete all as specified and directed. Note: (i) Two runs of single core cable with one run of earth continuity conductor including PVC casing caping & accessories shall be measured and paid as one length. (ii) Cutting chases shall be measured and paid separately.

S&F plastic plug and socket industrial type IP 54, 63 Amp, 5 Pole alongwith suitable size PVC box and 63 Amp 3 Phase MCB surface mounted complete with connection of incoming and outgoing cable, all as specified and directed. Make: Hager Cat Part No. VYB863C or equivalent model in Legrand/Siemens/ABB.

Supply and install split type Air conditioning units 1.5 TR indoor and outdoor complete with cordless remote control unit and with 5 star rated/BLDC type compressor unit with non CFC refrigerant, auto swing, LED display, noise level not more than 42 db function complete with all piping arrangment, etc complete all as specified and directed. Note : (i) Condensate drain pipe of best quality to be provided and fixed in suitable manner till ground level/max up to 6.0 Mtrs fixed on wall/floor/ceiling. (ii) The quoted rate includes necessary fixing arragement for indoor and outdoor units and copper tubing upto 6.00 mtr length, brazing, welding including insulation, complete charging of refrigerator gas upto required level and filling the cavities on wall and setting of grill alignment and including testing & commissioning, complete all as specified and directed.

S&F voltage stabilizer of capacity 5 KVA for automatic operation, single phase naturally air cooled indoor type & designed for input variation between 170 V to 250 V with output voltage stabilized at 230 V with accuracy of ± 2.5%, with digital display automatic high and low cut out with wall mounting accessories, complete all as specified and directed.

S&F power unit 4 module up to 25 Amps including sockets 25 Amps with six module concealed metal box for mounting of power unit and power socket, complete all as specified and directed.

S&F ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) including taking down old ceiling fan, any type and deposited to AGE E/M store yard, completes all as specified and directed.

S&F exhaust fan made of sturdy engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 300m, completes all as specified and directed.

S&F electric water heater, storage type steel inner tank or glass line coated tank (tank designed suitable to withstand 8 bar pressure) and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated with adjustable temp knob complete with all accessories such as safety valve, thermostate, NRV, connection piece etc., completes all as specified and directed.

Note: An amount of Rs.56,867.00 on account of Credit Schedule for schedule 'A' part - II shall be deducted from the total amount of BOQ to arrive at the contract sum.

M/S. VINITA CONSTRUCTION (BID ID -3123343)

SHRI SURAJIT SIKDER (BID ID -3122885)

MAJUMDER ENTERPRISE (BID ID -3123124)

M/S BIJAY KUMAR SHIVA (BID ID -3122837)