REPAIR TO FLOORS, TILING, JOINERIES, SHEET, PLUMBING WORKS AND CERTAIN MISC B/R WORKS AT SECT A AND SECT C UNDER AGE B/R-II UNDER GE DINJAN

Amount

Demolition of brick work or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars etc complete all as specified and as directed.

Taking down cement plaster on brick or stone walls etc including racking out joints, hacking for key, scrubbing down with water complete all as specified and as directed

Demolition of plain cement concrete (unreinforced) of any description and in any position not otherwise specifically provided for complete all as specified and as directed.

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided complete all as specified and as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and disposing the rubbish off the premises complete all as specified and as directed.

Dismantling wall and ceiling boards (fiber, pulp, insulation etc.) any thickness including cover fillets and frame work any type complete all as specified and as directed.

Dismantling of plain or corrugated steel sheeting, any gauge, thickness, in roof covering including ridges complete all as specified and as directed.

Dismantling of timber boarding of any description, fixed in any position with nails complete all as specified and as directed.

Dismantling timber scantlings 40 Sq.cm and over in section, in any position complete all as specified and as directed.

Dismantling of wrought iron or mild steel work of any description not otherwise provided for complete all as specified and as directed.

Taking down chowkats or frame not exceeding 1.5 Sqm in each with shutters (without taking off shutter from the frame) complete all as specified and as directed.

Taking down chowkats or frames exceeding 1.5 but not exceeding 4 Sqm in each with shutter (without taking off shutter from the frame) complete all as specified and as directed.

Taking down shutters of any description not exceeding 1 sqm each complete all as specified and as directed.

Taking down shutters of any description exceeding 1 sqm but not exceeding 2sqm each complete all as specified and as directed.

Taking down shutters of any description and refixing in same location/opening not exceeding 1 sqm each also refixing existing serviceable builders hardware complete all as specified and as directed.

Taking down shutters of any description and refixing in same location/opening exceeding 1 sqm but not exceeding 2sqm each also refixing existing serviceable builders hardware complete all as specified and as directed.

Resecuring or easing and adjusting without taking down shutters of any description exceeding 1 Sqm but not exceeding 2 Sqm each also refixing existing serviceable builders hardware complete all as specified and as directed.

M&L for brick work using locally available first class bricks sub class 'B' bricks (old size brick), straight or curved on plan exceeding 6 m mean radius, built in cement mortar (1:6) complete all as specified and as directed.

M&L for brick work using locally available first class bricks sub class 'B' bricks (old size brick), straight or curved on plan exceeding 6 m mean radius, built in cement mortar (1:4) complete all as specified and as directed.

M&L for brick work with sub class 'B' bricks, straight or curved on plan to any radius, built in cement mortar (1:4) as in half brick thick walls complete all as specified and as directed.

M&L for 75mm thick plain cement concrete (1:4:8) type D-2 (using 40 mm graded stone aggregate) for sub base or floor complete all as specified and as directed.

M&L for plain cement concrete (1:4:8) type D-2 (using 40 mm graded stone aggregate) as in foundation, filling and mass concrete etc complete all as specified and as directed.

M&L for 75 mm thick, plain cement concrete (1:3:6) type C-2 (using 40mm graded stone aggregate) as in plinth protection, footpath, etc, finishing cement concrete surface even and smooth without using extra cement including making joints with bitumastic filing in proportion of bitumen and sand (1:2) making impressions of expanded metal whilst the concrete is green complete all as specified and as directed.

M&L for non-skid, ceramic, joint free, coloured tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. including 15 mm thick screed bed in cement mortar (1:6) and set & jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles complete all as specified and as directed.

M&L for non-skid, ceramic, joint free, coloured tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, as in skirting etc. including 10 mm thick backing coat in cement mortar (1:4) and set & jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles complete all as specified and as directed.

M&L for granite stone slab (of any type) 18 to 20 mm thick, machine cut, as in cooking platform bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including 15mm thick screed bed in cement mortar (1:6) & cutting, rounding to edge of slab, polishing complete all as specified and as directed.

M&L for granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including 15mm thick screed bed in cement mortar (1:6) complete all as specified and as directed. .

M&L for glazed, coloured, ceramic, tiles of size 400mm x 300 mm x 6 to 7 mm thick, on vertical surfaces such as skirting, dados etc, including 10 mm thick plaster in cement mortar (1:4) and set & jointed in neat cement slurry & pointed in white or coloured cement to match with the shade of tiles complete all as specified and directed.

M&L for glazed, ceramic, coloured tiles of size 300mmx200mmx7-8mm thick, on vertical surfaces, including 10 mm thick backing of cement mortar (1:4) and set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles complete all as specified and as directed.

M&L for chequered cement concrete tiles of size 20cm x 20cm x 25mm thick, as in floors etc, including 15 mm thick screed bed in cement mortar (1:6) and set & jointed in neat cement slurry and pointed in grey cement and pigments to match with the shade of tiles complete all as specified and as directed.

M&L for machine cut kota stone slab flooring 18 to 20mm thick over cement screed bed laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing, polishing and 15 mm thick, screed bed in cement mortar (1:6) complete all as specified and as directed.

M&L for rendering 15 mm thick in cement mortar (1:4) (with approved water proofing compound) on fair faces of brick masonry or concrete surfaces and finishing the surfaces even and smooth without using extra cement complete all as specified and as directed. Note : WPC @ 2% of cement, shall be paid separately.

M&L for 15 mm thick rendering in cement mortar (1:6) on fair faces of brick masonry or concrete surfaces and finishing the surfaces even and smooth without using extra cement complete all as specified and as directed.

M&L for 10 mm thick rendering in cement mortar (1:4) on fair faces of brick masonry or concrete surfaces and finishing the surfaces even and smooth without using extra cement complete all as specified and as directed.

M&L for 5 mm thick rendering in cement mortar (1:3) on concrete surfaces as in ceiling (sunshade, chajja etc) and finishing the surfaces even and smooth without using extra cement complete all as specified and as directed.

Supply only integral liquid water proofing compound complete all as specified and as directed.

M&L for reinforced cement concrete (1:2:4) type B-1 (Nominal Mix) (using 20 mm graded stone aggregate) as in slab supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed. Note : Reinforcement shall be measured and paid separately under relevant item.

S&F for TMT steel bars 10mm dia and over, cut to length, bend to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and as directed.

M&L for form work to soffits of suspended slabs such as roof slab landings and similar works not exceeding 200mm thick (horizontal or slopping) fair finished surfaces of concrete flat complete all as specified and as directed.

M&L for form work to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, opening in concrete walls, floors and roofs exceeding 5cm but not exceeding 10cm wide fir rough finished surfaces of concrete flat complete all as specified and as directed.

M&L for second class hardwood, timber scantlings, clean swan as in framed and fixed, with nails complete all as specified and as directed.

S&F in repairs 18/19mm thick veneered particle board, interior grade, fixed in cupboard shelves, interior grade, solid core, medium density, general purposes, with commercial face veneer type 'BB' complete all as specified and as directed.

Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or steel frames, concrete or brick surrounds, glazed with putty or fixed with beads complete all as specified and as directed.

S&F for 3 mm thick sheet glass, ordinary quality and glazing with oil putty in square not exceeding 0.5 Sqm in each pane complete all as specified and as directed.

S&F for 4.8 mm thick sheet glass, ordinary quality and glazing with oil putty in square exceeding 0.5 Sqm in each pane complete all as specified and as directed.

S&F for stainless steel wire mesh, 0.36 mm nominal dia of wire and average width of aperture 1.4mm and fixed with stainless steel wire staples including necessary welding work complete all as specified and as directed.

S&F in repairs stainless steel wire mesh, 0.36 mm nominal dia of wire and average width of aperture 1.4mm and fixed with stainless steel wire staples including necessary welding work complete all as specified and as directed.

S&F in repair galvanised mild steel wire cloth, 0.56 mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks or galvanised wire staples including timber bead complete all as specified and as directed.

S&F for galvanised mild steel wire cloth, 0.56 mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks or galvanised wire staples including timber bead complete all as specified and as directed.

S&F in repairs curtain rails, harrison rail, mild steel chromium plated with fixing brackets, stops, rollers etc complete all as specified and as directed.

S&F for 0.63 mm thick, galvanised, corrugated mild steel sheeting with two corrugation side lap, fixed with L-type or J-type or cranked hook bolts and washers, in roofs, with grade of zinc coating 120gm per sqm, conforming to IS -277-2003 complete all as specified and as directed.

S&F for 0.63 mm thick, Plain, galvanised, mild steel sheeting, in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) with grade of zinc coating 275, complete all as specified and as directed.

S&F for pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of profile as approved, any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed.

S&F for pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of profile as approved, any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed.

S&F for aluminium anodised snap grid frame work of size 600mm x 600mm frame work for ceiling with aluminium tee section of size 23.5mm x 26.4mm x 1.4mm thick and aluminium angle section of size 36.5mm x 25mm x 1.4mm thick, for false ceiling including Hangers 4 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia, 40mm long including 4 mm thick non asbestos E-board (plain), HSPC fixed to frame including providing two coats of white wash complete all as specified and as directed. Make of E-Board : Eternit Everest / Lafarge/ Armstrong/Visaka Industries Ltd.

S&F for 20mm thick, second class hardwood boarding, planed one side with butt joints and fixed in position as in eaves board etc complete all as specified and as directed.

M&L for 4mm thick asbestos plain building board fixed with timber frame work as in ceiling complete all as specified and as directed

S&F for false ceiling with exposed metal (PPGI) framework/ "Tee" grid providing and fixing of suspended Tee grid false ceiling using 'T" grid system - powder coated GI (PPGI) exposed grid false ceiling suspension system in grid size 600mmx600mm with main runner 32mm x 24mm x 0.3mm thick, cross tee 26mm x 24mm x 0.3mm thick and wall angle 24mm x 24mm x 0.40 mm thick using 4mm thick non asbestos fiber cement board of size 595mm x 595mm, and asbestos free fiber cement board manufacturer using high pressure system curing technology. T grid framing is suspended using 4mm GI/MS bar hanger fixed with steel dash fasteners or iron purlin from the roof with adjustment clip, also providing provisions for light fixtures, air conditioning diffusers and ducts, sprinklers, smoke detectors etc. The main runners to be secured to structural soffit by hanger @ 1220mm maximum c/c. The last hanger at the end of each main runner should not be placed at not more than 300mm from the adjacent wall. 1220mm/600mm cross tee to be interlocked between main runners @ 600mm c/c, so as to form 600mm x 600mm or 1200mm x 600mm grid, confirming IS 14862 and type B category III of ISO 8336, tested as per AS 1530 Part-3 & B. S-476 Part 4, 5, 6, 7 & 8 should be placed in grid module to form after and including dismantling of existing false ceiling of any type complete all as specified and as directed.

S&F for well seasoned second class hard wood plain, solid, straight chowkat and frames, wrought, framed, rebated on the solid rounded or chamfered, put together with glue pinned at joints complete all as specified and as directed.

S&F pressed steel frames for doors local work shop made of size 125x60mm with one or more rebates using cold rolled commercial mild steel sheet of 1.2mm thick including providing and fixing necessary lugs, 100mm butt hinges, lock strike plate, shock absorber etc and including PCC filling of hollow section using plain cement concrete (1:3:6) type C1 complete all as specified and as directed.

S&F for pressed steel frames for doors local work shop made of size 105x60mm with one or more rebates using cold rolled commercial mild steel sheet of 1.2mm thick including providing and fixing necessary lugs, 100mm butt hinges, lock strike plate, shock absorber etc and including PCC filling of hollow section using plain cement concrete (1:3:6) type C1 complete all as specified and as directed.

M&L for 35 mm thick, second class hardwood glazed and skeleton shutters (factory made) open rebated and prepared to receive glass, gauge, etc, (without sash bars) edges of framing plain, chamfered or rounded, fitted with cut and mitered beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I Section 8 clause 8.24 (a) complete all as specified and as directed..

S&F for 30 mm thick, second class hardwood glazed and skeleton shutters open rebated and prepared to receive glass, gauge, etc, divided in to squares, with plain, chamfered or rounded, mitered sash bars, any numbers, timber beads for securing glass etc sizes of members of shutters as specified in SSR Part I Section 8 clause 8.24 (a) complete all as specified and as directed.

M&L for 35mm thick second class hard wood plain, framed, panelled shutters (any number of panels), with lock rail and panels of 9mm BWP commercial ply or 12mm thick veneered particle board medium density with commercial face veneers supplied and fitted to chowkats. The size of rail & styles 150mm and 10mm. Sizes/section of members of shutters shall be as specified in SSR Part I, Section -8, clause 8.24 (a) complete all as specified and as directed..

S&F for 35 mm thick flush door shutter, solid core construction, with particle board core and plywood face panels, commercial type on both sides with internal jointless lipping not less than 25 mm depth complete all as specified and as directed.

S&F for solid PVC door frames of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube complete all as specified and as directed.

S&F for factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded, plain colour PVC 'C' channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, panelling of plain colour 5mm thick PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement complete all as specified and as directed.

S&F for 100mm size butt hinges, medium weight, cold rolled mild steel complete all as specified and as directed.

S&F for 75mm size butt hinges, medium weight, cold rolled mild steel complete all as specified and as directed.

S&F for 75 mm size butt hinges, medium weight, stainless steel complete all as specified and as directed.

S&F for 150 mm size mild steel pressed handles, oval type, stove enamelled black complete all as specified and as directed.

S&F for 150 mm size aluminium anodised handles, cast type complete all as specified and as directed.

S&F for 100 mm size aluminium anodised handles, cast type complete all as specified and as directed.

S&F for 200 mm long mild steel, tower bolts, stove enamelled black, with bright bolt complete all as specified and as directed.

S&F for 150mm long mild steel, tower bolts stove enamelled black, with bright bolt complete all as specified and as directed.

S&F for 100mm long mild steel, tower bolts stove enamelled black, with bright bolt complete all as specified and as directed.

S&F for 150 mm long aluminium anodized, barrel tower bolts of extruded section complete all as specified and as directed.

S&F for mild steel sliding door bolts, 250mm long, plate type, stove enamelled black, with bright bolts not less than 12mm dia with & including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate etc complete all as specified and as directed.

S&F in repairs 150 mm size mild steel pressed handles, oval type, stove enamelled black complete all as specified and as directed.

S&F in repairs 200 mm long mild steel, tower bolts, stove enameled black, with bright bolt complete all as specified and as directed.

M&L for mild steel framed work such as grills, gratings, gates etc., with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bar, barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks and similar work conforming to Fe-290 (Gde E-165) complete all as specified and as directed.

S&F for mild steel small articles using flat iron of size 25x3mm thick such as band, strap, hold fast, cleat, support, hook, hinges, base tie for door frame etc and other similar items conforming to Fe-290 (Gde E-165) complete all as specified and as directed.

M&L for rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates conforming to Fe-290 (Gde E-165) complete all as specified and as directed.

M&L for plain cement concrete (1:3:6) type C-1 (using 20 mm graded stone aggregate) for fixing hold fast complete all as specified and as directed.

S&F as in repair steel windows with side hung shutters including box type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded including painting with one shop coat of zinc chrome primer complete all as specified and as directed.

S&F as in repair steel windows with side hung shutters including box type hinges with steel handle, and steel peg stay, complete without glazing bars, dovetailed or welded including painting with one shop coat of zinc chrome primer complete all as specified and as directed.

S&F in repairs steel ventilators with top hung shutters including hinges and steel peg stay complete all as specified and as directed.

M&L for anodised aluminium frame of doors, windows, ventilators with one or more rebates including joining cleats for fixing etc including powder coating of minimum 50 micron thickness complete all as specified

S&F for anodised aluminium door shutters, aluminium section weighing 0.55 kg/m including necessary joining cleat glazing clips, rubber neoprene packing handle 2 Nos in each door, hinges, anodised aluminium snap beading screw etc. including powder coating of minimum 50 micron thickness complete all as specified and as directed.

M&L for anodised aluminium window and ventilator shutters, fixed type, with or without sash bar, using aluminium section weighing not less than 0.55Kg per metre including necessary joining cleats, glazing clips, rubber neoprene packing, aluminium handles 2 numbers in each shutter, hinges, anodised aluminium snap beading, screws etc complete all as specified and as directed.

S&F for aluminium anodised (Deco) pattern grill 75X75mm mesh size for window, 7mm to 8mm thick, design No 102, including suitable F/H section frame, aluminium cleat, fixed with steel screw to window frame complete all as specified and as directed.

S&F for 150mm dia (overall length of cover plate) floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified and as directed.

S&F for 12mm thick prelaminated particle board, interior grade, both side with decorative choice lamination, fixed with screws to timber frame works as in shutter of cup board and other similar work complete all as specified and as directed.

Taking up or down 15 mm bore steel water tubing galvanised including connections from trenches/wall/floor/ceiling etc and keeping serviceable quantity in safe custody for reuse at same site or other site complete all as specified and as directed.

Taking up or down 20 mm bore steel water tubing galvanised including connections from trenches/wall/floor/ceiling etc and keeping serviceable quantity in safe custody for reuse at same site or other site complete all as specified and as directed.

Refixing of 15mm bore old serviceable steel tubing and connections in new or old position with new fittings complete to walls and ceilings or laid in floors, etc retrieved from relevant item here in before respectively complete all as specified and as directed.

Refixing of 20mm bore old serviceable steel tubing and connections in new or old position with new fittings complete to walls and ceilings or laid in floors, etc retrieved from relevant item here in before respectively complete all as specified and as directed.

Supply, laying, connection and testing, 15mm bore, steel water tubing, galvanised, medium grade conforming to IS 1239 (Part -1):2004 with all fittings conforming to IS 1239 (Part -2):2011 and fixtures fixed to walls and ceilings or laid in floors, etc complete all as specified and as directed.

Supply, laying, connection and testing, 20mm bore, steel water tubing, galvanised, medium grade conforming to IS 1239 (Part -1):2004 with all fittings conforming to IS 1239 (Part -2):2011 and fixtures fixed to walls and ceilings or laid in floors, etc complete all as specified and as directed.

Cutting chases, pinning in, making good to facings where required and pointing in cement mortar (1:3) to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc. and cutting chases for concealed water tubing or concealed conduit wiring, etc. and making good, cutting not exceeding 10 cm girth complete all as specified and directed.

S&F in repairs plastic water closet seat, back, closed pattern with flat bottom and cover and mild steel chromium plated or aluminized hinging device complete all as specified and as directed.

S&F in repairs 10 litre capacity, PVC valve less symphonic duel type, flushing cistern, low level, white, with inlet, ball valve, flush pipe, float and handle including brackets complete all as specified and as directed.

S&F in repairs 20 mm bore, ball valves high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed. (Minimum weight - 210 gms) complete all as specified and as directed.

S&F 20 mm bore, ball valves high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed. (Minimum weight - 210 gms) complete all as specified and as directed.

S&F in repair top cover for water storage tank suitable for 250 to 1000 litres complete all as specified and as directed.

S&F in repairs, vitreous China wash down water closet pan (pedestal pattern), white, including connection to outgoing drain and flushing pipe, anti syphonic pipe with seat and cover complete but excluding flushing cistern & flush pipe including making good to disturbed surfaces of floor using concrete (1:2:4) type B0 and to match with existing specifications complete all as specified and as directed. Make : Cat No. C0287/0288 of Parryware/Hindware/Cera.

S&F in repairs vitreous china squatting pan, 'Orissa' pattern, size 580 x 440 mm white with integral foot rest and 'P' or 'S' trap, including provision of lime concrete bedding, connection to trap and flushing pipe etc complete including making good to disturbed surfaces of floor using concrete (1:2:4) type B0 and to match with existing specifications complete all as specified and as directed. Make : Cat No. C0117 of Parryware/Hindware/Cera.

S&F in repairs sink with drainage board, made out of stainless steel 1.00mm thick, kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 915x460mm and bowl size 410X330X160mm complete all as specified and as directed. Make : Prayag/Anjali/Blue Star.

S&F for stainless steel plate rack 1mm thick, standard quality, size 900 x 900 x 250mm complete all as specified and as directed.

S&F in repairs 32mm/40mm dia and 800mm waste pipes for sink / wash hand basin/ urinal complete all as specified and as directed.

S&F in repairs vitreous china wash basin, size 550x400mm, white, flat back, with PVC waste pipe, CP waste coupling, chain, plug and porcelain stopper & brackets including cutting for and pinning in ends of brackets but excluding tap complete all as specified and as directed. Make : Cat No. C0406 of Parryware/Hindware/Cera.

S&F in repairs 15 mm bore, bib taps, cast copper alloy, chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and as directed.

S&F in repairs 15 mm bore, stop valves, cast copper alloy, chromium plated with long shank and cup (concealed type), screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions complete all as specified and as directed.

S&F in repairs 15 mm bore, pillar taps, fancy type, cast copper alloy, chromium plated with capstan heads, screwed down high pressure with or without lettered 'Hot or Cold' with long screwed shanks and fly nuts, screwed for iron pipe complete all as specified and as directed.

S&F 15 mm bore, pillar taps, fancy type, cast copper alloy, chromium plated with capstan heads, screwed down high pressure with or without lettered 'Hot or Cold' with long screwed shanks and fly nuts, screwed for iron pipe complete all as specified and as directed.

S&F in repairs 15mm dia angular stop cock cast copper alloy, screwed down high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions complete all as specified and as directed. Make : Cat No. T3507A1 of Parryware/Hindware/Cera.

S&F in repair brass cast copper alloy, chromium plated shower rose 125mm size with shower arm 15mm size, 195mm long fixing to steel pipe or to unions complete all as specified and as directed.

S&F in repairs 15 mm bore, bib taps, PTMT, any colour, high pressure screwed for iron pipes or brass ferule and fixed (min weight 90 gms) complete all as specified and as directed.

S&F in repairs 15 mm bore, stop valve , PTMT, any colour, high pressure screwed for iron pipes or unions and fixed (min weight 120 gms) complete all as specified and as directed.

S&F in repairs 15mm bore, PVC connection pipe 600mm long with PTMT nuts at both ends complete all as specified and as directed.

S&F in repairs 15mm bore, PVC connection pipe 450mm long with PTMT nuts at both ends complete all as specified and as directed.

S&F in repairs swivel shower of PTMT 15mm bore (minimum weight 40 gms) including shower arm 15mm size, 195mm long with bend of 45 degree with flange of PTMT any colour (minimum wt 40 gms) complete all as specified and as directed.

S&F in repairs 20mm bore, gun metal gate valves with iron wheel head screwed both ends for iron pipes or for unions complete all as specified and as directed.

S&F in repairs 50mm bore, high density poly-ethylene pipes (HDPE) of pressure rating 6 kgf/cm2 fixed to wall, ceiling or in floors complete all as specified and as directed.

S&F in repairs cascade health faucet including hook and hose not less than 1.2 metre long all as specified and as directed. Make : Cat No. T9803A1 of Parryware/Hindware/Cera/jaquar or equivalent

S&F in repair 100 mm bore, CI branch piece, single (equal or unequal) complete all as specified and as directed.

S&F in repairs grating doom 100mm dia of PTMT (Minimum weight 25gms) complete all as specified and as directed.

S&F in repairs PTMT (half or full threaded) waste coupling 40mm for sink (min weight 32mm - 45gms/40mm - 60gms) complete all as specified and as directed.

S&F in repair brass chromium plated tubular towel rail, D type, 60cm long, 20mm dia with brackets complete all as specified and as directed.

Dismantling of rotational moulded polyethylene water tank of capacity exceeding 250 litres but not exceeding 500 Ltrs complete all as specified and as directed.

Dismantling of rotational moulded polyethylene water tank of capacity exceeding 500 litres but not exceeding 1000 Ltrs complete all as specified and as directed.

S&F for 500 litres capacity rotational moulded polyethylene water storage tanks (cylindrical or vertical with closed top) as per IS 12701:1996, hoisted and fixed in position including provision of 20/15mm bore medium grade pipe for connecting inlet, outlet, overflow and washout pipe complete all as specified and as directed.

S&F for 1000 litres capacity rotational moulded polyethylene water storage tanks (cylindrical or vertical with closed top) as per IS 12701:1996, hoisted and fixed in position including provision of 20/15mm bore medium grade pipe for connecting inlet, outlet, overflow and washout pipe complete all as specified and as directed.

Cleaning and removing all scale and dirt, etc. from tanks of capacity exceeding 250 Ltr & not exceeding 500 Ltrs and from mouths of circulating pipes, etc. complete all as specified and as directed.

Cleaning and removing all scale and dirt, etc. from tanks of capacity exceeding 500 Ltr & not exceeding 1000 Ltrs and from mouths of circulating pipes, etc. complete all as specified and as directed.

Disconnecting existing water tank of capacity not exceeding 500 litres, reconnecting and refixing in position including cleaning and removing all scale and dirt, etc from tank and from mouth of circulating pipes, washing the internal surfaces with bleaching powder etc and writing letters on outer face of tank with white paint complete all as specified and as directed.

Disconnecting existing water tank of capacity exceeding 500 litres & not exceeding 1000 litres, reconnecting and refixing in position including cleaning and removing all scale and dirt, etc from tank and from mouth of circulating pipes, washing the internal surfaces with bleaching powder etc and writing letters on outer face of tank with white paint complete all as specified and as directed.

M&L for preparation of new untreated wood and wood based surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed.

M&L for preparation of new steel surfaces of any description, over 10 cm in width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of zinc chrome, red oxide primer complete all as specified and as directed.

M&L for preparation of new plastered surfaces of wall and applying three coats of white wash complete all as specified and as directed.

M&L for preparation of new plastered surfaces of ceiling and applying three coats of white wash complete all as specified and as directed.

M&L for preparation of new plastered surfaces of brick work or previously untreated and applying two coats of oil bound distemper over one coat of alkali resistant primer complete all as specified and as directed.

M&L for preparation of new plastered surfaces of wall and applying two coats of oil bound distemper over one coat of chalk whiting complete all as specified and as directed.

M&L for preparation new external surfaces of wall, chajja, facia etc and applying two coats of water based acrylic weather proof exterior emulsion (exterior wall finish) paint over a coat of primer as per manufacturer's instruction complete all as specified and as directed.

S&F in repairs mild steel 300 mm ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and as directed.

M&L for water proofing treatment on RCC roof etc. comprising with the following operation and as specified herein below and as directed:- (a) Taking down existing old tarfelt, bituminous compound including plaster etc, cleaning & removing debris to a distance exceeding 100m & not exceeding 250m. (b) 15 mm thick plastering in cement mortar (1:4) finished even & smooth. (c) Preparing & cleaning of fully dried cement plastered surface. (d) Applying one coat of cold bituminous primer to the plastered surface @ 0.25 liters per sqm conforming to IS-3384 (e) A layer of APP based polymeric membrane 3mm thick (minimum) weighing 3.5 kg per sqm reinforced with polyester non woven fabric (weighing not less than 160 gms/sqm )shall be applied over bituminous primer as specified above. Application of polymeric membrane shall be by torch application. The over lap shall be minimum 100 mm on transverse direction and 75 mm in longitudinal direction. (f) One coat of aluminium paint over the APP based membrane @ 0.11 Kg/Sqm

S&F for 110mm PVC (SWR) pipes single sockets, in any length with rubber ring joints, fixed to walls complete all as specified and as directed.

S&F in repairs 75mm PVC (SWR) pipes single sockets, in any length with rubber ring joints, fixed to walls complete all as specified and as directed.

S&F for 110 mm bore, PVC (SWR) bends of any radius complete all as specified and as directed.

S&F in repairs 75 mm bore, PVC (SWR) floor trap, with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified and as directed.

R D Enterprises

M/S AUTOMOTIVE WORLD

M/s GANDHESWAR PHUKAN

FREEZCON

M/S CHANDAN ENTERPRISE

STANDARD ELECTRIC WINDERS

M/S BORAH BROTHERS