CEAFU-05-23-24 MODIFICATION OF BLAST PENS AT AF STATION SRINAGAR

Amount

SCHEDULE 'A' PART-I FOR RECASTING OF FLOOR OF BLAST PENS/RELAYING OF TAXI TRACK:

Demolition of unreinforced cement concrete (PQC) in ground floors and pavings exceeding 15 cm thickness (below or above ground level) complete all as specifed and as directed by Engineer-in-Charge.

Rolling and consolidation formation surfaces in cutting at OMC to achieve 98 percent of maximum of dry density with 8 to 12 Tonne power roller including filling in soft spots, depression etc., which occur during rolling (for portion coming in cutting/original ground only) to required level and gradient including watering before and during rolling, complete all as specified and directed.

M&L for 150 mm thick (compacted thickness) shingle/gravel GSB Gde-I River bed (90mm to 63mm size of aggregate) over compacted sub grade filling in floor or paving laid in layers not exceeding 150mm thick spread levelled to required gradient including watering,rolling with power roller 8 to 12 tonne capacity complete all as specified and directed.

150 mm thick (compacted thickness) shingle/gravel WMM (Wet Mix macadam) 40mm size of aggregate over compacted sub grade filling in floor or paving laid in layers not exceeding 150mm thick spread levelled to required gradient including watering, rolling with power roller 8 to 12 tonne capacity complete all as specified and directed by Engr in charge.

M&L for 100 mm thick DLC (Dry lean concrete), M-15 over soiling layer type B- 2, Design mix using minimum 290 Kg of cement per cum with 40mm graded crushed stone aggregate) laid with mechanical paver, rolled and consolidated to required gradient and camber with 8 to 12 tonne power roller, complete all as specified and as directed. NOTE:- (a) No price adjustment shall be applicable if quantity of Cement content used in the work as approved in the Design Mix exceeds 290 Kg. (b) The rate quoted shall be inclusive of use and waste of form work for total thickness.

M&L for 10 mm thick sand filling under polythene film all as specified and as directed. NOTE: Polythene film 400 micron shall be measured and paid separately under relevant item of this BOQ.

M&L for polythene film 400 micron thick, black spread and laid over sand layer with minimum 15 cm side and ends laps as per IS-2508, complete all as specified and directed at site. (Note:- Net covered area shall be measured and paid without adding any allowance of overlaps).

325mm thick PQC cement work with of minimum flexural strength 40 Kg per Sq cm in field in pavement slabs, using minimum 400 Kg of cement per cubic metre ,design mix, laid with mechanical paver as specified and consolidated in bays to required gradient and camber including necessary steel form work and mixed with non circular synthetic fibre reinforcement @ 0.25% of weight of ordinary portland cement grade 43 of PQC or as per manufacturers instruction, mixed in batching plant transported to site, laid in panels, spread and compacted, mechanically vibrated and bull nosing / rounding off the edges, including curing compound, finishing the surface by belting and brooming without using extra cement etc. complete all as specified and as directed Note : (i) Nothing to be paid over and above 400kg/Cum. (ii) Non circular traingular synthetic fibre shall be measured and paid separately.

Supply only polyester made non circular fibres with cut length between 12-18 mm having tensile strength 300 MPa, melting temperature minimum 250 degree Celsius having specific gravity 1.34 to 1.39 with equivalent fibre diameter 15-40 micron @ 0.06 to 0.30 percent by volume in controlled cement concrete complete as specified and directed and as discribed in relevant PS Clause.

M&L for forming 25mm wide expansion joints through the full thickness 325mm of the slab filled with 25mm thick synthetic compressive filler board HD-100 and cleaning 30mm deep left over to top cavity and top 10mm primed with N-49 primer and filled with polyurethane thermo setting type sealant seal over 30mm dia polyethylane back up rod and material including pasting polythlene adhesive tape 25mm wide all along on the both edges of joint and removing the same after filling and tooling the material inside the joint to remove spilled over material complete all as per manufacturer's instructions wiith movement accomadation factor of (+) 30% with performance warranty of 10 years complete all as specified and directed by the GE.

M&L for forming construction joints 10mm wide and 25mm deep for quality concrete slab, cleaning the complete joint and top 13mm primed with N-49 primer and filled with polyurethane thermo setting type sealant seal over 12mm dia polyethylane back up rod and material including pasting polythlene adhesive tape 25mm wide all along on the both edges of joint and removing the same after filling and tooling the material inside the joint to remove spilled over material complete all as per manufacturer instruction wiith movement accomadation factor of (+) 30% with performance warranty of 10 years complete all as specified and directed by the GE.

M&L for forming dummy joints 6mm wide and 100mm deep for quality concrete slab, cleaning the complete joint and top 13mm primed with N-49 primer and filled with polyurethane thermo setting type sealant seal over 8mm dia polyethylane back up rod and material including pasting polythlene adhesive tape 25mm wide all along on the both edges of joint and removing the same after filling and tooling the material inside the joint to remove spilled over material complete all as per manufacturer instruction wiith movement accomadation factor of (+) 30% with performance warranty of 10 years complete all as specified and directed by the GE. Note:Dummy joints shall be formed by using mechanical equipment(diamond cutter) within 6 hours of placing of concrete.

M&L for applying two coats of road marking paint (water based) over a coat of primer (Conforming to IS-164-1981) white or yellow after preparation of surfaces for lines, dashes arrows, letters etc., on bituminous surfaces/pavements exceeding 10 cms width using automatic mechanical nozzle sprey machine complete all as specified and as directed.

Removing demolished reinforced/plain cement concrete (RCC/PCC/PQC) exceeding 1.50 KM but not exceeding 5.00 KM and depositing where directed.

SCHEDULE 'A' PART-II FOR RECONSTRUCTION OF BLAST WALLS:

M&L for plain cement concrete 1:4:8 type D-2 using 40mm graded crushed stone aggregates as in sub base, foundation, filling and mass concrete, complete all as specified and as directed by Engineer-in-Charge.

M&L for reinforced cement concrete M-30 (Design mix) using 20 mm graded crushed stones aggregates, as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specifed and as directed.

M&L for reinforced cement concrete M-30 (Design mix) using 20 mm graded crushed stones aggregates, as in walls, traverse walls, retaining walls, basement walls, ballast walls and the like; any thickness; above top of footings; including attached pilasters and buttresses complete all as specifed and as directed.

M&L for reinforced cement concrete M-30 (Design mix) using 20 mm graded crushed stones aggregates, as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specifed and as directed.

M&L for form work to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter for rough finished flat surfaces of concrete, complete all as specified & directed. all as specified and directed.

M&L for formwork to faces of walls, treverse walls, retaining walls, abutments, parapets and staircase railings and similar work including attached pillasters, buttresses, etc.; vertical or to batter for rough finished flat surfaces of concrete, complete all as specified & directed. all as specified and directed.

M&L for formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; exceeding 200mm thick (Horizontal or sloping for rough finished flat surfaces of concrete, complete all as specified & directed. all as specified and directed.

M&L for TMT Mild steel bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and as directed.

M&L for TMT Mild steel bars 5mm dia and over upto and including 10mm dia as in stirrups, spacers and binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and as directed.

M&L for hand packing (any thickness) using broken stone or boulders at back of walls over arches etc., and raising (or lowering) to the required level, complete all as specified and as directed.

M&L for 25 mm thick preformed filler board for crumple joints complete all as specified and as directed.

S&F for 0.71 thick plain, aluminium sheeting, alloy 31000 H4 in ridges, hips, valley gutter, drip and straight flashing (length and girth as fixed) complete, complete all as specified and as directed.

S&F for 4.00 mm dia plain mild steel wire, galvanised class 3, as in tieing wire for camouflaging net, in fencing including straining and fixing to wood, concrete or steel posts and/or to straining bolts, including securing with and provision of galvanised iron tying wire, galvanised iron staples or steel pins, etc. as directed (each line of wire to be measured) complete all as specified and as dirceted.

M&L for preparation of newly plastered or concrete surfaces of walls and applying two coats of 'Apex ultima paint' over external surfaces of walls over a coat of primer over and including one coat of 2mm thick brila white wall care putty, complete all as specified and as directed.

Supplying and fixing or laying 75 mm bore PVC (SWR) pipes, single socketed in any length, as in weep holes and the like, complete all as specified and as directed.

Demolition of reinforced cement concrete in ground floors and pavings thickness exceeding 15cm complete all as specified and directed.

SCHEDULE 'A' PART-III FOR ADDITIONAL STRUCTURE OF BLAST WALL

M&L for plain cement concrete 1:2:4 type B-2 using 40mm graded crushed stone aggregates as in sub base, foundation, filling and mass concrete, complete all as specified and as directed by Engineer-in-Charge.

S & F for rolled sections Fe-410-W (Gde-E-250) quality-B, as in main and cross beams, hip and jack rafters; purlins where connected to commen rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates, complete all as specified and as directed.

S & F for Fe-410-W (Gde-E-250) quality-B, plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, with riveted, bolted or welded attachment etc all as specified and as directed.

M&L for preparation of new steel or iron surfaces of any description, over 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint (any tint) over a coat of red oxide primer complete all as specified and as directed.

M & L for 8mm dia galvanised steel wire rope 6*19 tensile strength 1770 N/mm2 connected to hook etc, complete all as specified and as directed.

S&F of mild steel clamps with two bolts size for looping suitable for mild steel wire rope complete all as specified and as directed.

S&F galvanised iron turn buckel of M-16 Eye to hook type,body length 170-180 mm, all as specified and as directed.

S&F straining bolts/eye bolt of 16 mm dia including moulding to the required shape and with nut &washers,minimum length 300 mm confirming to Fe-290 Gde-E-165 etc, completed all as specified and as directed.

SCHEDULE 'A' PART-IV FOR INTERNAL ELECTRIFICATION WORKS

Taking down carefully copper/aluminium flame proof point wiring (light, socket or power) complete, including fixture and fittings such as swithces, ceiling roses, pendants, sockets, light fitting etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc. complete all as specified and as directed.

M&L for flame proof Point wiring for one light point controlled by one flame proof rotary single pole one way switch with 1.5 sqmm PVC insulated and unsheathed fire retardant low smoke and halogen (FR-LSH) copper conductor single core multi stranded copper cable conforming to IS:694 (2010) using approved colour code for phase and neutral as per IS code drawn through ERW metallic rigid steel stove enamelled black heavy duty concealed conduit ISI Marked, corrosion resisitant, heavy protection grade in accordance with IS:9537 (Part 2) having wall thickness not less than 1.8 mm thick and minimum 20 mm external dia but shall be increased as per actual site requirement in accordance with clause No 19.125 of SSR Part I ( ISI marked) including steel conduit accessories like bends, tees, junction boxes duly tested and approved by CMRI Dhanbad etc fixed concealed including PVC insulated and unsheathed FRLSH 1.5 sqmm multi stranded copper conductor cable (green color) as continuous earth lead wire connected to common earth and earth dolly complete all as specified and directed by Engineer-in-Charge.

M&L for flame proof Point wiring for one switch socket outlet controlled by one independent flame proof switch socket and plug combined with 2.5 sqmm PVC insulated and unsheathed fire retardant low smoke and halogen (FR-LSH) copper conductor single core multi stranded copper cable conforming to IS:694 (2010) using approved colour code for phase and neutral as per IS code drawn through ERW metallic rigid steel stove enamelled black heavy duty concealed conduit ISI Marked, corrosion resistant, heavy protection grade in accordance with IS:9537 (Part 2) having wall thickness not less than 1.5 mm thick and minimum 20 mm external dia but shall be increased as per actual site requirement in accordance with clause No 19.125 of SSR Part I (ISI marked) including steel conduit accessories like bends, tees, junction boxes duly tested and approved by CMRI Dhanbad etc fixed concealed including PVC insulated and unsheathed FRLSH 2.5 sqmm multi stranded copper conductor cable (green color) as continuous earth lead wire connected to common earth and earth dolly complete all as specified and directed by Engr-in-Charge.

Supply and fixing non integral LED flood light fitting 1x120 Watt flame proof-Exd suitable for 240V AC, 50Hz supply, CSIR-CIMFR certified recommended for gas/vapor group of IIA & IIB, Zone 1 & 2 & 21 and IP 65 protection with Grey Epoxy Powder Coated Pressure Die Cast LM6 Aluminium Alloy Housing with heat resistant toughened glass, Impact Resistance - IK08, 6500K, corrosion resistant finish, LED driver (with built in voltage surge protection, short Circuit & Over Voltage protections), holders, connector etc. LED lighting & control gear should comply with the relevant electromagnetic compatibility standards IEC: 61000-3-2/IS: 14700-3-2, IEC: 61000-3-3 and IEC: 61547. The luminaire shall be designed for L70 of not less than 50000hrs (min) and failure fraction of 10% (max) with minimum 125 lumen/watt, Power Factor - >0.97, THD - <10% including cradle to hang the fitting complete with all accessories prewired and including connecting up with three core flexible copper conductor cable with suitable size complete all as specified and as directed.

BLANK

Supply and fixing switch rotary type single pole,16A, 250V flame proof-Ex"d" suitable for 240V AC, 50Hz supply, CSIR-CIMFR certified recommended for gas/vapor group of IIA & IIB, Zone 1 & 2 & 21 with termination box in LM6, IP 65 protection, conforming to IS-2148:2004/IEC 60079-1 (2007) complete all as specified and as directed.

Supply and fixing Flame proof Ex "d ", weather proof interlocked switch socket & plug combined, 16A, 250V, 2P+earth, in cast aluminium alloy LM6 construction suitable for 240V AC, 50Hz supply, CSIR-CIMFR certified recommended for gas/vapor group of IIA & IIB, Zone 1 & 2 & 21, conforming to IS 2148:2004 (IEC-60079-1/2007) complete all as specified and as directed.

Supply and fixing Flame proof Ex "d " ,weather proof interlocked switch socket & plug combined, 16A, 500V, 3P+earth, in cast aluminium alloy LM6 construction suitable for 415V AC, 50Hz supply, CSIR-CIMFR certified recommended for gas/vapor group of IIA & IIB, Zone 1 & 2 & 21, conforming to IS 2148:2004 (IEC-60079-1/2007) complete all as specified and as directed.

Supply & fixing of Flameproof Ex"d", weather proof MCB Distribution Box , TPN 4 way, 430V, 50Hz, CSIR-CIMFR certified recommended for gas/vapor group of IIA & IIB, Zone 1 & 2 & 21 and IP 66 weather proof protection with Grey Epoxy Powder Coated Pressure Die Cast LM6 Aluminium Alloy Housing, suitable for flush mounting or surface mounting, with suitable size of Busbar for each phase, Neutral Bar, Earth Bar and Cable ties for cable management, with Provision for MCCB as incomer and SP/TP MCB's Outgoing including dissmantling existing one with its accessories, cutting chases to wall for fixing DB and making good the disturbed wall surface complete all as required at site and as directed comprising of following items as under:-

(a) Incomer - MCCB 4 Pole 40 A with Electronic Protection Unit Ics=100% Icu, Adjustable overload protection .4 to 1 x In, Protection against Short curcuit 1.5 to 10 Ir, inbuilt instatneous protection,complete all as directed and specified Qty - 01 Nos

(b) Outgoing (i) MCB single pole 240 volts 10 Amps, C Curve, with rupturing capacity 10 KA ISI marked Biconnect lower terminals, IP 20 protected terminals, sliding shutters Qty -02 Nos (ii) MCB single pole 240 volts 16 Amps, C Curve, with rupturing capacity 10 KA ISI marked Biconnect lower terminals, IP 20 protected terminals, sliding shutters Qty -01 Nos (iii) MCB Tripple pole 415 volts 20 Amps, C Curve, with rupturing capacity 10 KA ISI marked Biconnect lower terminals, IP 20 protected terminals, sliding shutters Qty -02 Nos (iv) MCB Tripple pole 415 volts 25 Amps, C Curve, with rupturing capacity 10 KA ISI marked Biconnect lower terminals, IP 20 protected terminals, sliding shutters Qty -01 Nos

Supply & fixing of Flameproof Ex"d", weather proof MCB Distribution Box, TPN 4 way, 430V, 50Hz, CSIR-CIMFR certified recommended for gas/vapor group of IIA & IIB, Zone 1 & 2 & 21 and IP 66 weather proof protection with Grey Epoxy Powder Coated Pressure Die Cast LM6 Aluminium Alloy Housing ,suitable for flush mounting or surface mounting, with suitable size of Busbar for each phase, Neutral Bar, Earth Bar and Cable ties for cable management, with Provision for MCCB as incomer and SP/TP MCB's Outgoing including dissmantling existing one with its accessories, cutting chases to wall for fixing DB and making good the disturbed wall surface complete all as required at site and as directed comprising of following items as under:-

(a) Incomer - MCB 4 Pole 25 A, C Curve, with rupturing capacity 10 KA ISI marked Biconnect lower terminals, IP 20 protected terminals, sliding shutters Qty -01 Nos

(b) Outgoing (i) MCB single pole 240 volts 10 Amps, C Curve, with rupturing capacity 10 KA ISI marked Biconnect lower terminals, IP 20 protected terminals, sliding shutters Qty -02 Nos (ii) MCB single pole 240 volts 16 Amps, C Curve, with rupturing capacity 10 KA ISI marked Biconnect lower terminals, IP 20 protected terminals, sliding shutters Qty -02 Nos (iii) MCB Tripple pole 415 volts 20 Amps, C Curve, with rupturing capacity 10 KA ISI marked Biconnect lower terminals, IP 20 protected terminals, sliding shutters Qty -01 Nos

Supply & Fixing of Distribution Board weather proof cabinets made of Impact resistant reinforced polystyrene material, 4 Module, 230V, 50Hz, IP-65 & IK-09, class-II insulated enclosure, door and cabinet fully reversible, removable chassis, lockable door handle, sealable cover and faceplates including weatherproof glands, rails etc complete with copper busbar insulated fork type 63A as short link including end caps and provision of MCB DP 10 A 230 V, 50 HZ, C curve Qty- 1 Nos, MCB SP 6 A 230 V Qty - 2 Nos, 50 HZ, C curve with blanking plates if required complete all as specified and as directed.

Earthing complete with copper earth plate electode of size 600 mm x 600 mm x 3.15 mm thick burried directly in ground (earth pit not less than 2.25 meter deep below normal ground level connected to and including copper strip earth lead 20 x 3mm by means of bolts, nuts, chock, nuts and washers of galvanised iron or steel including PCC Pit in 1:2:4 type B-1 angle iron frame with RCC cover and handle, excavation and earth work in any type of soil, medium grade GI watering pipe 20mm bore with funnel and wire mesh and light grade GI protection pipe 25mm bore upto main board complete all as shown in electrical plate No 3 of MES Sch 2009 (Part I) connected to main control board as specified and testing completion complete all as specified and directed. Note: (i) The unit rate includes GI pipe up to 7.5m for protection of earth lead. For any additional length the same shall be adjusted through deviation order. (ii) The unit rate includes main earthing lead/strip from earth electrode to test point up to 7.5 meter (iii) In case measured value of earth resistance is recorded more than 1.0 ohms then the earthing shall be re done by the contractor without any extra cost to the department.

Supply and Fixing earth continuity conductor or main earthing lead fixed to wall on batten or recess or chases or buried in ground or drawn in conduit/pipe or fixed to poles or any other indicated situation for loop earthing etc as required copper earth strip 20x3 mm dia.

Supply and fixing hot pressed moulded Glass reinforced polyester sheet moulding compound (SMC) Junction box of dimensions 170mm x 170mm x 105mm outside diemnsion, SMC confirming to IS: 13410:1992 Grade S 1 ,thickness of SMC sheet not less than 1.5mm, outdoor type, single door hinged with front side opening, weather proof, suitable locking arrangement at front, arrangement for incoming and out going cable entry at the bottom ,earthing arrangement using one no. of Earthing bolt of MS with 2 nuts and 2 washers provided on RH side of box, Earthing sign has to be provided near to earthing bolt complete all as specified and comprising of the followings items as under:- (a) single phase and neutral bus bar duly colour coded of capacity 100 amps using aluminium strips of size 25mm x 4mm mounted on epoxy resin base insulators, drilled holes for cable connection on bus bar including provision of PVC cable of suitable size and length from bus bar to MCB (b) Fixing arrangent and material required for installation on walls

Supply, laying, jointing and testing, fixing to wall using clamps/pole/floor or in air or passing through pipes/ducts/road/path/drain, laid in trenches, 1100 volts grade heavy duty electric cable XLPE insulated, screened, PVC bedded, galvanised steel wire or wire armoured with electric power cable 1100 volts grade with stranded aluminium conductor of size 2 core 6 sqmm conforming to IS - 7098 Part-1 and its latest amendments complete all as specified and as directed by Engr-in-Charge.

S&F GI pipe light grade 25mm dia as protection to cable along the pole/across road crossing/through culvert/passing through ceiling/walls with necessary clamps using suitable size Flat iron with, nuts and bolts for fixing on wall / pole complete all as specified and as directed.

M&L Sub main wiring using PVC insulated and unsheathed fire retardant low smoke and halogen (FR-LSH) copper conductor single core multi stranded copper cable conforming to IS:694(2010) using approved colour code for phase and neutral as per IS code drawn through ERW metallic rigid steel stove enamelled black heavy duty concealed conduit ISI Marked, corrosion resisitant, heavy protection grade conforming to IS:9537 (Part 2) in accordance with clause No 19.125 of SSR Part I including steel conduit accessories like bends, tees, junction boxes duly tested and approved by CMRI Dhanbad etc fixed concealed external dia as under but shall be increased as per actual site requirement complete all as specified and as directed by Engineer-in-Charge of the following sizes of cables as under. Note: Rate of point wiring shall include cutting chases for conduit/flush boxes etc

(a) Using four single core PVC insulated FRLSH cable 4 sqmm copper conductor multi stranded (Phase and neutral) and 4.0 sqmm copper conductor PVC insulated FRLSH cable as earth wire through ERW metallic rigid steel stove enamelled black heavy duty concealed conduit having wall thickness not less than 1.8 mm thick and minimum 25 mm external dia but shall be increased as per actual site requirement complete with all accessories Note: 4 runs of 4sqmm copper cable & 1 run of 4.0sqmm copper cable in and including 25mm ERW metallic steel conduit shall be measured as one unit

Supply and laying or fixing or passing through pipe, 1100 volts grade heavy duty cable with PVC insulated aluminium conductor served with an inner sheathing of PVC tape armoured with galvanised steel wire or tape and overall PVC sheathed 4 sqmm nominal cross section 3 core in service connections complete all as specified and as directed.

SCHEDULE 'A' PART-V FOR EXTERNAL WATER SUPPLY WORKS

Supply, installation, testing and commissioning of open well submersible self priming non clog pump with copper rotor suitable for turbid water application suitable for 3 phase 415 volts, capacity 1050 LPM at 25mtr head, size of inlet x outlet (80mm X 65mm) conforming to IS 14220 (1994) with stainless shaft, bronze bush and stamping lamination with high permeability steel for long life and increased efficiency, impeller cast iron. Insulation: B class Protection: IP 68. The cap of motor in HP/KW shall be as per recommendation of the manufacturer. The motor shall be conforming to IS:9283(1994) with minimum 69% efficiency and guaranteed Pump efficiency at design flow should be equal or greater than 65%. complete all as specified and as directed by Engr-in-charge.

Supply and Fixing submersible pump cable of size 2.5 sqmm flat 3 core, XLPE insualted and sheathed with PVC, multi stranded copper conductor cable, 1100 volts grade and connecting complete all as specified and as directed by Engr-in-charge.

S&F GI tubing medium grade, ISI Marked conforming to IS 1239 Part-I 2004, 100mm bore with and including all fittings such as bends, elbows, tees, short length, socket, union, check nuts, nipples etc. fixed and laid in trenches/floor/under culvert/road crossing etc including testing complete all as specified and as directed.

S&F GI tubing medium grade, ISI Marked conforming to IS 1239 Part-I 2004, 80mm bore with and including all fittings such as bends, elbows, tees, short length, socket, union, check nuts, nipples etc. fixed and laid in trenches/floor/under culvert/road crossing etc including testing complete all as specified and as directed.

Material and labour for construction of valve chamber of size 750 x 750 x 750 mm deep dimensions (Over all internal dimension) with PCC foundation, brick masonry walls, Plastering, PCC Coping, mild steel chamber cover, painting to chamber cover including excavation and earth work in any type of soil complete all as specified below:- Valve chamber shall be provided with the following specifications:- (i) Cement concrete for foundation (1:4:8) type D2 using 40mm graded crushed stone aggregates 150 mm thick extended up to 150 mm beyond the outer face of block masonry. (ii) Walls of valve chamber 230 mm thick with using brick masonary setting in CM 1:6 complete. (iii) Internal and exposed surfaces of valve chamber both concrete and brick masonry surface shall be plastered with CM (1:4), 15 mm thick finished even and smooth. (iv) 50 mm thick coping in PCC 1:3:6 type C1 over brick masonry wall. (v) Chamber cover shall be of 6 mm thick MS sheet with 30 x 30 x 5 mm size angle iron frame with hold fast and locking arrangement. Steel surface shall be painted with two coats of synthetic paint of first quality over one coat of red oxide primer complete all as specified and as directed by Engr-in-charge.

S&F Bronze/Gun metal gate valve class-1 for 100mm bore pipe, with iron wheel head, screwed both ends for iron pipe and fixed, ISI marked conforming to IS 778: 1984 complete all as specified and directed.

M & L for Earthing complete with galvanised steel earth electrode plate of size 600x600x6mm thick, buried directly in ground(earth pit not less than 2.25m deep below normal ground level) with top edge of the plate not less than 1.50m below normal ground level, connected to galvanised steel earth lead wire 4 mm dia as earth lead up to test point with suitable GI nuts/bolts and brazed properly up to main board including earth pit in cement concrete 1:2:4 type B-1 using 20mm graded stone aggregates,40mm thick precast RCC cover in 1:2:4 reinforced with expanded metal(weight not less than 4 kg/sqm), and frame of angle iron 25x25x6mm with lugs 02 nos with 6mm dia MS bar handle made to shape, excavation and earth work in any type of soil and including medium grade GI watering pipe 20mm bore with funnel and wire mesh and medium grade GI protection pipe 15mm bore up to main board complete as shown in electrical plate no 3 of MES schedule Part-I , connected to earthing testing point and testing on completion complete all as specified and directed by Engineer-in-Charge. Note: (i) The unit rate includes GI pipe up to 7.5m for protection of earth lead. For any additional length the same shall be adjusted through deviation order. (ii) The unit rate includes main earthing lead/strip from earth electrode to test point up to 7.5 meter (iii) In case measured value of earth resistance is recorded more than 1.0 ohms then the earthing shall be re done by the contractor without any extra cost to the department.

SCHEDULE 'A' PART-VI FOR EXTERNAL ELECTRIFICATION WORKS

M&L for sand cushioning to underground cable with dry sand locally available 8cm thick before laying of the cable and 15cm thick after laying and strectching the cable below the bricks/PCC cover, punning of sand using suitable T&P as per site condition, complete all as specified and as directed by Engineer-in-Charge. Note: Punned thickness of sand to be consider for measurement purpose.

Supply and lay common burnt clay sub class B bricks of size 230mm x 115mm x 75mm laid dry and flat at right angle over the cable along the length of trench complete all as specified and as directed.

S&F GI pipe light grade 80 mm dia as protection to cable along the pole / across road crossing/through culvert/passing through ceiling/walls with necessary clamps of flat iron with ,nuts and bolts for fixing on pole complete all as specified and as directed.

S&F GI pipe light grade 50 mm dia as protection to cable along the pole / across road crossing/through culvert/passing through ceiling/walls with necessary clamps of flat iron with ,nuts and bolts for fixing on pole complete all as specified and as directed.

Supply, laying, jointing and testing, fixing to wall using clamps/pole/floor or in air or passing through pipes/ducts/road/path/drain, laid in trenches, 1100 volts grade heavy duty electric cable XLPE insulated, screened, PVC bedded, galvanised steel wire or wire armoured with electric power cable 1100 volts grade with stranded aluminium conductor of size 3.5 core 120sqmm conforming to IS - 7098 Part-1 and its latest amendments complete all as specified and as directed by Engr-in-Charge.

Supply, laying, jointing and testing, fixing to wall using clamps/pole/floor or in air or passing through pipes/ducts/road/path/drain, laid in trenches, 1100 volts grade heavy duty electric cable XLPE insulated, screened, PVC bedded, galvanised steel wire or wire armoured with electric power cable 1100 volts grade with stranded aluminium conductor of size 3.5 core 35sqmm conforming to IS - 7098 Part-1 and its latest amendments complete all as specified and as directed by Engr-in-Charge.

Supply, laying, jointing and testing, fixing to wall using clamps/pole/floor or in air or passing through pipes/ducts/road/path/drain, laid in trenches, 1100 volts grade heavy duty electric cable XLPE insulated, screened, PVC bedded, galvanised steel wire or wire armoured with electric power cable 1100 volts grade with stranded aluminium conductor of size 2 core 6sqmm conforming to IS - 7098 Part-1 and its latest amendments complete all as specified and as directed by Engr-in-Charge.

Supply, laying, jointing and testing, fixing to wall using clamps/pole/floor or in air or passing through pipes/ducts/road/path/drain, laid in trenches, 1100 volts grade heavy duty electric cable XLPE insulated, screened, PVC bedded, galvanised steel wire or wire armoured with electric power cable 1100 volts grade with stranded aluminium conductor of size 4 core 25sqmm conforming to IS - 7098 Part-1 and its latest amendments complete all as specified and as directed by Engr-in-Charge.

Supply, laying, jointing and testing, fixing to wall using clamps/pole/floor or in air or passing through pipes/ducts/road/path/drain, laid in trenches, 1100 volts grade heavy duty electric cable XLPE insulated, screened, PVC bedded, galvanised steel wire or wire armoured with electric power cable 1100 volts grade with stranded aluminium conductor of size 4 core 16sqmm conforming to IS - 7098 Part-1 and its latest amendments complete all as specified and as directed by Engr-in-Charge.

Supply, laying, jointing and testing, fixing to wall using clamps/pole/floor or in air or passing through pipes/ducts/road/path/drain, laid in trenches, 1100 volts grade heavy duty electric cable XLPE insulated, screened, PVC bedded, galvanised steel wire or wire armoured with electric power cable 1100 volts grade with stranded aluminium conductor of size 4 core 10 sqmm conforming to IS - 7098 Part-1 and its latest amendments complete all as specified and as directed by Engr-in-Charge.

Supply, installation, testing, commissioning of 'Silent type' diesel generating set alongwith having prime power rating of 20kVA/16 kWe, 415Volts at 1500RPM, 0.8 lagging power factor at 415 volts suitable for 50 hz 3 phase system and for 0.85 load factor, CPCB-II complied, acoustic enclosure, relay panel for automatic starting on main failure (AMF), anti vibration mountings, control panel and foundation.The DG set should be robust in construction factory tested and assembled to ensure perfect alignment of Engine and Alternator on a common base frame.The DG set power rating indicated above is inclusive of altitude correction factor however the DGSet shall be designed and suitable to operate as per tropical condition of Srinagar and for more details on service condition refer particualr specification.The DG set shall be comprising of following item as under:-

(a) Diesel Engine : The diesel engine shall be of four stroke cycle multi-cylinder, direct injection water cooled, turbo charged with after cooler, Air to air aftercooling and optimised turbocharger for increased altitude capabilities developing suitable BHP @ 1500 RPM under tropical condition of Srinagar of BS 5514/ISO 3046 with an over load capacity of 110% for one hour in any specified 12 hrs of continuous operation,suitable for generating set application on AMF mode.The engine shall confirm to IS:10000/BS:649/BS 5514/ISO 3046. The engine shall have the following accessories: (i) Cooling fan and radiator. (ii) DM water cooling systems with pre-mix anti-corrosive additive. (iii) Turbocharger. (iv) Fly wheel with fly wheel housing. (v) Electrical engine starter motor (disengagement after start-up) with Batteries. (vi) Battery charging systems. (vii) Industrial/Residential silencer and exhaust pipes having suitable height with supporting structure. (viii) Stainless steel exhaust flexible elbow. (ix) Thermal sealing of exhaust pipe and aluminium cladding for complete exhaust pipe and silencer. (x) Required filters for fuel, lube oil, air etc. (xi) Sets of flexible hoses as required. (xii) Suitable rubber coupling to Alternator with guard. (xii) Suitable Engine controller for protection of the engine. (xiii) Coolant heater. (xiv) Oil drain Pump. (xv) Heavy duty air cleaner.

(b) Engine protections: (i) High coolant temperature warning & trip. (ii) Low lubricating oil pressure warning & trip (iii) Low coolant level warning & trip. (iv) Fail to crank trip. (v) Over crank trip. (vi) High and Low speed trip (vii) Low or High battery voltage alarms. (viii) Clogged filter warning. (ix) Lack of fuel. (x) High Canopy Temperature. (xi) Set fail to start protection after failure of the set to start after successful three consecutive start attempts.

(c)Starting system :The engine starting shall be by means of totally enclosed axial type electric starter suitable for 12volts/24 volts DC starting system comprising of starter motor, voltage regulator and arrangement for initail exciation complete with suitable number of batteries(25 plates, 180AH Sealed Maintenance Free (SMF) Lead-Acid type) as required as per specifications.The battery shall be supplied with a suitable floor mounted MS stand treated with seven tank treatment, two coats of red oxide /primer & acid resistant paint.with wooden base, adaptor box etc . with copper conductor battery leads of required length and socket/clamps

(d) Governor :The governor shall be of electronic type suitable for monitoring constant engine speed within the specified limits for auto parallel and auto load sharing operation.

(e) Exhaust : The exhaust piping system shall be supplied with a hospital grade silencer and catalytic converter suitably optimized to meet stringent noise emission standards laid down by MoEF / CPCB.The exhaust piping and the silencer shall be wrapped with rock wool and/or calcium silicate. The outside shall be neatly wrapped with aluminum cladding. The exhaust line shall be extended beyond the height of the utility building roof as required by pollution control norms.Suitable supporting structure for installation shalll be provided.

(f) Hot air exhaust (Radiator cooling): GI duct shall be provided for hot air exhaust from DG set up to designated place of duct outlet. The duct shall be made of 14 Gauge thick Class-8, Galvanized Iron (GI) Sheet.Galvanised Iron (GI) duct shall be provided for venting hot exhaust air out of the DG room, from radiator hot air outlet point of the DG Acoustic enclosure through nearest brick wall.

(g) Fuel Tank : Inbuilt/internal bottom mounted (with-in DG set or with-in base frame) diesel tank of suitable capacity with mounting brackets, complete with fuel inlet, out let, air vent, drain plug, level indicator, inter connection pipes from tank to diesel generator as required. Suitable barrier shall be provided between Diesel tank and the Engine. Fuel tank shall be fabricated as per tropical condition of Srinagar and designed capacity shall be suitable for 8 hrs continous operation.

(h) Alternator: 20 kVA 3 phase 0.8 PF 415V, 4 wire 1500 rpm self-excited and self regulated through AVR confirming to IS :4722/BS 2613 suitbale for tropical condition with brush less exciter, housed in screen protected drip proof enclosure. The alternator shall be confirming to IS 13364 Part-2 & IS 15999 Part-1/ IEC 60034 Part-1 capable of delivering rated output at rated power factor with (i) Terminal voltage differing from the rated value by not more than +/- 5%. (ii). Frequency differing from the rated value by not more than +/-0.5%. (iii). Short circuit capacity of 300% for 10 seconds. (iv). Over load capacity of 110% for one hour. The insulation class of the Alternator shall be class F/ H. The temperature rise shall be limited to class B and Ingresses enclosure protection shall IP23 or better. The alternator shall be fitted with suitable Nos. Resistance Temperature Device (RTD) & Bearing Temperature Device (BTD) along with space heaters.

(j) Alternator Protection :Alternator should have following protections (i) Over and Under voltage (ii) Under and Over frequency warning and trip (iii) Loss of excitation (iv) Over current and Earth Fault and Short Circuit Protection (v) Unbalanced loads (vi) Restricted Earth Fault Protection.(vii) Differential protection. (viii) Diode Failure.

(k) Voltage regulator :A rapid response voltage regulator shall be provided to regulate the generated voltage.The overall regulations from no load to full load, including cold to hot variation and load power factor of 0.8 lag to unity shall be within 2% of the normal voltage. The excitation system shall be designed to promote rapid voltage recovery following sudden application and disconnection of load.

(l) Acoustic enclousure : The acoustic enclosure should be supplied along with DG set from the manufacturer outlet itself as per CPCB norm.Acoustic enclosure shall be of powder coated and fabricated out of 2mm thick CRCA MS sheet. The canopy shall have four hinged doors, one door with glass window to view proper parameters on the control panel. The canopy and doors shall have inside lining of fire retardant foam/glasswool as acoustic materials. The base frame shall be fabricated in ISMC channel or in sheet metal, with lifting hooks for convenient lifting of complete set i.e. along with canopy, engine and alternator. The sound level shall have less than 75 db (A) at a distance of 1 meter.High quality noise absorbant and fire-retardant grade acoustic Insulation material (P.U. Foam) complying to IS 8183. The allowable temperature raise inside the canopy is 5 to 7 deg. Centigrade. The Measurement of noise should be as per ISO 3744/ ISO 8528 (Part 10) standard.The canopy has the provision of emergency push button, external to the canopy

(m) AMF Control Panel :The control panel shall be designed for Automatic ON Mains Failure Operationof the Generator sets. The Panel will be totally enclosed, Dust tight, vermin proof,floor mounted, free standing, cubical compartmentalized type with hinged doors, fabricated from 14 SWG CRCA Steel metal having separatecompartments . The Panel will be epoxy painted powder coated with light grey shade, After Seven Tank treatment, and the Panel / compartment will be fitted with the following instrument and pre-wired with colour coded flexible copper cable with ferule Numbers for easy identification & maintenance. The panel shall be complete with interconnections, insulators, two nos. of earthing lugs and with suitable rating of MCCB at both the end & shall incorporate the followings: -

(xiv) Set of relays and contractor of suitable capacity with MCCB, 4 pole,63 Amps, 415 Volt. 25 KA for automatic start & automatically shut down of DG set or as per manufacturer recoomendation of suitable rating & capacity - 02 Nos. (xv) By pass arrangement by providing on laod change over switch 63 Amps 4 pole to be installed with AMF- 02 Nos.

Note : 1. AMF Panel shall be installed outside the acoustic enclousre 2. Cost of DG set foundation deemed to be included in cost of item. 3. Contractor should submit necessary drawing to GE for approval prior placing the order.

M & L for Earthing complete with galvanised steel earth electrode plate of size 600x600x6mm thick, buried directly in ground(earth pit not less than 2.25m deep below normal ground level) with top edge of the plate not less than 1.50m below normal ground level, connected to galvanised iron strip of size 25 x 4 mm as earth lead up to test point with suitable GI nuts/bolts and brazed properly up to main board including earth pit in cement concrete 1:2:4 type B-1 using 20mm graded stone aggregates, 40mm thick precast RCC cover in 1:2:4 reinforced with expanded metal(weight not less than 4 kg/sqm), and frame of angle iron 25x25x6mm with lugs 02 nos with 6mm dia MS bar handle made to shape, excavation and earth work in any type of soil and including medium grade GI watering pipe 20mm bore with funnel and wire mesh and medium grade GI earth wire protection pipe 40mm bore up to main board complete as shown in electrical plate no 3 of MES schedule Part-I, connected to earthing testing point and testing on completion complete all as specified and directed by Engineer-in-Charge. Note: (i) The unit rate includes GI pipe up to 7.5m for protection of earth lead. For any additional length the same shall be adjusted through deviation order.(ii) The unit rate includes main earthing lead/strip from earth electrode to test point up to 7.5 meter (iii) In case measured value of earth resistance is recorded more than 1.0 ohms then the earthing shall be re done by the contractor without any extra cost to the department.

Supply and fixing GI tube Medium grade 40mm bore for protection of earth lead including all fittings complete all as specified and as directed by Engineer-in- charge.

Supply and fixing earth continuity conductor of size 25 x 4mm galvanised iron strip, burried into ground or any other indicated situation for loop earthing etc. complete all as specified and as directed by Engineer-in-Charge.

Supply, installation, testing and commissioning of LT Feeder Pillar outdoor type confirming of IS 5039, CPRI approval, totally enclosed vermin proof suitably ventilated for 3 phase, 4 wire 415 Volts, 50Hz, AC supply, outer sheel shall be made out of 3.15mm thick CRCA sheet & MS angle section of suitable size for frame, factory fabricated, compartmentalized inner shell shall be made of out of 2.0 mm thick CRCA sheet for control gear. Front and back door operating with locking arrangement at front. Panel shall be provided with proper ventilation arrangement from both sides including ventilation fan etc.Protection of enclosure IP 56 with pre-treatment through 7 tank hot chemical process prior to powder coated with minimum 50-70 micron of approved colour. The bottom of outer shell contains a detachable plate having provision for entry of armoured cable of adequate size. Computer cut self adhesive vinyl danger notice plate having conventional symbol of bones and skull to be provided.The panel shall be provided with manufacturer name plate,heavy duty SS cable glands of adequate size for incoming and outgoing cables. EPDM gasket of appropriate shape and size provided at all joints, door and covers including suitable size angle iron/flat iron frame work/support required with four legs 60cm long using angle iron 40 x 40 x 6mm duly painted with anti corrosive paint, air passing holes and locking arrangement at front with duplicate keys and making connection of incoming and outgoing cable using proper cable lugs, 4 x legs 40 cm grouted in PCC 1:2:4 and making good distrubed surface complete and comprising of the following:-

(A) (i) TPN Aluminium electrolytic grade bus bar of capacity 125 Amps for phases & 63 Amps for neutral and auxillary bus bar to support main busbar duly supported on SMC/DMC, busbar supports and insulated with colour coded heat shrinkable sleeve (ii) Digital multifunction meter (V,A,KW,KWH), 415 AC alongwith C.T's of suitable ratio (40/5A class 5, 3VA) (set of three), class 1.0, complete (iii) Indication lamps LED type (RYB) =01 set of three. (iv) Internal wiring with suitable size of FRLS copper conductor cable.

B. INCOMER (i) MCCB 4 Pole 40 Amp, 16 KA, lcs = 100% lcu, with thermal magnetic release, adjustable overload 80-100% and adjustable short ckt 5 to 10 ln setting complete with phase seperator - 01 nos (ii) Panel mounted on load change over switch without enclosure front opertaed 4 pole 63 amps, 415V -01 nos

C. OUTGOING (i) Motor Protection Circuit breaker 4.0kW, 6-10 Amp adjustable thermal release range, 3 phase AC conforming to IEC 60947-4-1, Breaking capacity Icu 50 KA at 440 V AC 50/60 Hz conforming to IEC 60947-2, Rated service short-circuit breaking capacity Ics 100 % at 440 V AC 50/60 Hz compliance to standard IEC 60947-1, IEC 60947-2 & IEC 60947-4-1, complete all as specified -04 Nos. Note: The MPCB voltage rating must match the name plate voltage of the motor.

Note: (i) LT panel shall be CPRI approved (ii) Contractor shall submit the following Test report i.e. IP Test Report and verification of short circuit withstand test report in respect of LT Panel (iii) Contractor shall submit drawing to GE for approval prior to place order.

Supply, installation, testing and commissioning of LT Feeder Pillar outdoor type conforming of IS 5039, CPRI approval, totally enclosed vermin proof suitably ventilated for 3 phase, 4 wire 415 Volts, 50Hz, AC supply, outer sheel shall be made out of 3.15mm thick CRCA sheet & MS angle section of suitable size for frame, factory fabricated, compartmentalized inner shell shall be made of out of 2.0 mm thick CRCA sheet for control gear. Front and back door operating with locking arrangement at front. Panel shall be provided with proper ventilation arrangement from both sides including ventilation fan etc.Protection of enclosure IP 56 with pre-treatment through 7 tank hot chemical process prior to powder coated with minimum 50-70 micron of approved colour. The bottom of outer shell contains a detachable plate having provision for entry of armoured cable of adequate size. Computer cut self adhesive vinyl danger notice plate having conventional symbol of bones and skull to be provided.The panel shall be provided with manufacturer name plate,heavy duty SS cable glands of adequate size for incoming and outgoing cables. EPDM gasket of appropriate shape and size provided at all joints, door and covers including suitable size angle iron/flat iron frame work/support required with four legs 60cm long using angle iron 40x40x6mm duly painted with anti corrosive paint, air passing holes and locking arrangement at front with duplicate keys and making connection of incoming and outgoing cable using proper cable lugs, 4 x legs 40 cm grouted in PCC 1:2:4 and making good distrubed surface complete and comprising of the following:-

A. (i) TPN Aluminium electrolytic grade bus bar of capacity 100 Amps for phases & 50 Amps for neutral and auxillary bus bar to support main busbar duly supported on SMC/DMC, busbar supports and insulated with colour coded heat shrinkable sleeve (ii) Digital multifunction meter (V,A,KW,KWH), 415 AC alongwith C.T's of suitable ration (set of three), class 1.0, complete (iii) Indication lamps LED type (RYB) =01 set of three. (iv) Internal wiring with suitable size of FRLS copper conductor cable.

B. (i) MCCB 4 pole 40 Amp, 16 KA, lcs = 100% lcu, with thermal magnetic release, adjustable overload 80-100% and adjustable short ckt 5 to 10 ln setting complete with phase separator - 01 no

OUTGOING C. (i) MCCB 4 pole 25 Amp, 16 KA, with thermal magnetic release, lcs = 100% lcu, adjustable overload 80-100% and adjustable short ckt 5 to 10 ln setting complete with phase separator - 01 no

Note: (i) LT panel shall be CPRI approved (ii) Contractor shall submit the following Test report i.e. IP Test Report and verification of short circuit withstand test report in respect of LT Panel (iii) Contractor shall submit drawing for approval prior to place order.

Supply, installation, testing and commissioning of LT Feeder Pillar outdoor type confirming of IS 5039, CPRI approval, totally enclosed vermin proof suitably ventilated for 3 phase, 4 wire 415 Volts, 50Hz, AC supply, outer sheel shall be made out of 3.15mm thick CRCA sheet & MS angle section of suitable size for frame, factory fabricated, compartmentalized inner shell shall be made of out of 2.0 mm thick CRCA sheet for control gear. Front and back door operating with locking arrangement at front. Panel shall be provided with proper ventilation arrangement from both sides including ventilation fan etc.Protection of enclosure IP 56 with pre-treatment through 7 tank hot chemical process prior to powder coated with minimum 50-70 micron of approved colour. The bottom of outer shell contains a detachable plate having provision for entry of armoured cable of adequate size. Computer cut self adhesive vinyl danger notice plate having conventional symbol of bones and skull to be provided.The panel shall be provided with manufacturer name plate,heavy duty SS cable glands of adequate size for incoming and outgoing cables. EPDM gasket of appropriate shape and size provided at all joints, door and covers including suitable size angle iron/flat iron frame work/support required with four legs 60cm long using angle iron 40x40x6mm duly painted with anti corrosive paint, air passing holes and locking arrangement at front with duplicate keys and making connection of incoming and outgoing cable using proper cable lugs, 4 x legs 40 cm grouted in PCC 1:2:4 and making good distrubed surface complete and comprising of the following:

(A) (i) TPN Aluminium electrolytic grade bus bar of capacity 100 Amps for phases & 50 Amps for neutral and auxillary bus bar to support main busbar duly supported on SMC/DMC, busbar supports and insulated with colour coded heat shrinkable sleeve (ii) Digital multifunction meter (V,A,KW,KWH), 415 AC alongwith C.T's of suitable ratio (set of three), class 1.0, complete (iii) Indication lamps LED type (RYB) =01 set of three.(iv) Internal wiring with suitable size of FRLS copper conductor cable.

B. INCOMER (i) Motor Protection Circuit breaker 4.0kW 3 ph motor power, 6-10 Amp adjustable thermal release range ,3phase AC conforming to IEC 60947-4-1,Breaking capacity Icu 50 KA at 440 V AC 50/60 Hz conforming to IEC 60947-2,Rated service short-circuit breaking capacity Ics 100 % at 440 V AC 50/60 Hz conforming to IEC 60947-2, under voltage release, Shunt release, IK09 enclosure,IP20 conforming to IEC 60529, complete all as specified -01 Nos. Note: The MPCB voltage rating must match the name plate voltage of the motor.

C. OUTGOING : (i) Direct on line(DOL) starter in sheet metal enclosure for motor output upto 7.5kW,AC-3 phase,415 Volts, 50Hz,Relay Maximum Range 9-15 Amps -01 Nos.

Note: (i) LT panel shall be CPRI approved (ii) Contractor shall submit the following Test report i.e. IP Test Report and verification of short circuit withstand test report in respect of LT Panel (iii) Contractor shall submit drawing for approval prior to place order.

Dismantling / removing of old/unsv 3 phase fuse switch disconnector box 100 amp complete with all accessories all as specified and directed.

SCHEDULE 'A' PART-VII FOR AREA DRAINAGE/UNDER GROUND SUMP WORKS

M&L for plain cement concrete 1:3:6 type C-2 using 40mm graded crushed stone aggregates as in sub base, foundation, filling and mass concrete, complete all as specified and as directed by Engineer-in-Charge.

M&L for brick work with subclass ‘B’ bricks, straight or curved on plan exceeding 6m mean radius, built in CM 1:4, complete all as specified and as directed.

M&L for providing cement concrete 1:2:4 Type B0 (12.5 mm graded aggregate) in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs not provided for in roof kerbs or mud stops, rounded or chamfered on edges, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, complete all as specified and as directed.

M&L for 15mm thick rendering in cement mortar 1:4 on fair faces of brick work or concrete surfaces including finishing the surfaces even and smooth wihout using extra cement complete all as specified and as directed.

M&L for providing precast cement concrete 1:2:4 type B-1 using 20mm graded cushed stone aggregates, as in landings, cover slabs (for man holes etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces and setting in cement mortar 1:6 complete with joints to match complete all as specified & directed.

M&L for 10mm thick rendering in cement mortar 1:4 on fair faces of brick work or concrete surfaces including finishing the surfaces even and smooth without using extra cement mixed with integral water proofing admixture as per manufacturer's instructions complete all as specified and as directed. NOTE: Liquid water proofing admixture as supply only shall be measurd and paid separately under relevant item of this BOQ

Supply only liquid water proofing admixture all as specifed and as directed by the Engineer-in-Charge.

M&L for mild steel framed work such as grills, gratings, etc. with ends of bars shouldered and or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks and similar work conforming to Fe-290 grade-E-165, complete all as specified and as directed.

Supply and fixing for Expanded metal, cut to length, bent to shape required and tying with and including annealed mild steel wire not less than 0.90 mm dia for fixing with galvanised steel staples supplied and fixed complete to wood or steel members all as specified and as directed.

SCHEDULE 'A' PART-VIII FOR LIGHTENING PROTECTION WORKS

Dismantling of old air termination rod, GI pipe including necessary breaking of concrete block for mounting of the exiting termination rod and taking credit of the same

M & L for Air termination single pointed aluminium rod 12 mm dia and 300 mm long complete all as specified and directed

M &L for test point terminal block made of gun metal or phosphorus bronze 75 x 75 x 25mm, drilled and screwed including 3 Nos, 8mm dia, 25mm long hex head screw complete all as specified and as directed by Engr-in- Charge.

M&L for aluminium strip 25 x3mm with saddles and fixing screws etc for roof conductors and down conductors above ground for lightening conductor with epoxy insulators complete all as specified and as directed by Engineer-in- Charge

S&F of GI pipe, light grade 15 mm dia bore for installation of air termination rod including all fixing arrangements to walls and ceiling or laid all as required and directed by Engineer-in-Charge.

S&F of Galvanised iron strip 32 x 6mm buried in ground with saddles and fixing screws etc. for roof conductors and down conductors above ground all as specified and directed by Engineer-in-Charge.

M&L for precast cement concrete 1:2:4 type B-1 using 20mm graded stone crushed aggregates for support block of GI pipes and air termination rod (size of blocks 200 x 200 x 500mm or as per site requirement) all as required and directed by Engineer-in-Charge.

S&F for GI tubing light grade 40 mm dia complete with all fittings in trenches, fixed to wallls as specified and directed by Engineer-in-Charge.

SCHEDULE 'A' PART- IX FOR EXCAVATION EARTH WORK INCLUDING SITE CLEARANCE FOR ALL SCHEDULES OF THIS BOQ

Excavation in over areas not exceeding 1.50m deep in any type of soil and getting out soil, complete all as specified and as directed by Engineer-in-Charge.

Excavation in over areas exceeding 1.50m but not exceeding 3.00m deep in any type of soil and getting out soil, complete all as specified and as directed by Engineer-in-Charge.

Excavation in over areas exceeding 3.00m but not exceeding 4.50m deep in any type of soil and getting out soil, complete all as specified and as directed by Engineer-in-Charge.

Removing excavated soil not exceeding 50m and again removing the earth for forming embankment for earthen traverse for the new VIFT complete all as specified and as directed.

Rough excavation on existing earthern traverse required to be performed due to demolition of existing VIFT and reconstruction of new VIFT at 4 mtr horizontal distance from existing location, removal of the surplus soil to a distance exceeding 500 m but not exceeding 1.50 km and again removing the earth for reuse in filling/embankment formation for the new VIFT created. (Forming embankment paid separaetly).

Returning, filling in of excavated soil, including spreading, levelling, watering and well ramming in layers not exc 25 cm complete all as specified and as directed.

Removing excavated soil exceeding 500m but not exceeding 1500 m and again removing the earth for forming embankment for earthen traverse for the new VIFT complete all as specified and as directed.

M&L for forming embankment including raising (or lowering) earth, spreading in layer n exc, 30 cm thick, watering, ramming/rolling and finishing to required size etc, height not exceeding 1.50 mitres from base, compaction of earth filling shall be done under optimum moisture conditions complete all as specified and as directed.

M&L for forming embankment including raising (or lowering) earth, spreading in layer n exc, 30 cm thick, watering, ramming/rolling and finishing to required size etc, height exceeding 1.50 mitres but not exceeding 3.00 mitres from base, compaction of earth filling shall be done under optimum moisture conditions complete all as specified and as directed.

M&L for forming embankment including raising (or lowering) earth, spreading in layer n exc, 30 cm thick, watering, ramming/rolling and finishing to required size etc, height exceeding 3.00 mitres but not exceeding 4.50 mitres from base, compaction of earth filling shall be done under optimum moisture conditions complete all as specified and as directed.

M&L for forming embankment including raising (or lowering) earth, spreading in layer n exc, 30 cm thick, watering, ramming/rolling and finishing to required size etc, height exceeding 4.50 mitres but not exceeding 6.00 mitres from base, compaction of earth filling shall be done under optimum moisture conditions complete all as specified and as directed.

M&L for forming embankment including raising (or lowering) earth, spreading in layer n exc, 30 cm thick, watering, ramming/rolling and finishing to required size etc, height exceeding 6.00 mitres but not exceeding 7.50 mitres from base, compaction of earth filling shall be done under optimum moisture conditions complete all as specified and as directed.

M&L for forming embankment including raising (or lowering) earth, spreading in layer n exc, 30 cm thick, watering, ramming/rolling and finishing to required size etc, height exceeding 7.50 mitres but not exceeding 9.00 mitres from base, compaction of earth filling shall be done under optimum moisture conditions complete all as specified and as directed.

Excavating in post holes (or similar holes) each n exc 0.5 cum, in any type of soil, including getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25cm, watering and making good surface complete all as specified and as directed.

Removing excavated soil to a distance not exceeding 50m and depositing where directed at a level not exceeding 1.5 m above the starting point complete all as specified and as directed.

Excavation in over areas not exceeding 1.50m deep in any type of soil mixed with any size of stone boulders and getting out soil, complete all as specified and as directed by Engineer-in-Charge.

Removing excavated soil to a distance exceeding 1.50km but not exceeding 5.00 km and depositing where directed complete all as specified and as directed.

Excavating in trenches, n exc 1.5 m wide and n. exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, for laying cables/pipes, etc. n exc 10 sq m on plan in any type of soil and getting out soil, complete all as specified and as directed by Engineer-in-Charge.

Removing excavated soil to a distance exceeding 50m but not exceeding 250m and depositing where directed complete all as specified and as directed.

Removing excavated soil to a distance exceeding 250m but not exceeding 500m and depositing where directed complete all as specified and as directed.

NOTE: (i) Total amount of relevant part of Schedule of Credit amounting to Rs (as mentioned in Sch of credit) for retrieved material on relevant page of tender documents in PDF format which will be deducted offline during acceptance of Tender. (ii) The items having same description of different parts of this BOQ have been clubbed under one part of this BOQ to avoid duplicacy and also to avoid quoting of different rates for similar item(s) by the bidder(s).

Hassan Road Construction Co Pvt Ltd

Jai Ambey Construction Co.

M/S ABDUL SALAM MIR CONSTR CO PVT. LTD

Onkar Nath Bhalla And Sons Contractor Pvt. Ltd.