PROVN OF COVERING SHED FOR AUGMENTING WEATHER PROTECTION OF BLDGS AND URINAL FOR TRAINEES AT ALL ARMS WG AND TOILET FCE HQ AT MCTE UNDER GE (MCTE) MHOW

Amount

Excavating in post holes in soft/ loose soil (or similar holes) each n exc 0.5 cu.m. getting out, returning,filling in and ramming earth or broken rubble mixed with earth around, in layer not exceeding 25 cm, watering and removing surplus soil to a distance n.exc 50 M complete all as specified.

M&L for plain cement concrete 1:3:6 type C2 using 40mm graded crushed stone aggregate as in foundations filling and mass concrete complete all as specified.

Cutting channels, grooves or rebates n exc 15cm girth, and trimming surface With or without reinforcment, complete all as specified.

M&L for plain cement concrete type B1(1:2:4) using 20mm graded stone aggregate as in, copings, bed plates, and like including weathering slightly rounded or chamfered angles and throating, complete all as specified.

S&F Pre-painted galvalume aluminium zinc coating GI based profile steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa, hot dip alloy of 55% Aluminium 43.5% Zinc 1.5% Silicon and finished with resin coat on both surfaces @ 150 gm/sqm of coating (total both surfaces) as in roof covering/ cladding to wall,including flashings, ridges, valley etc fixed with self tapping screws complete all as specified.

S&F Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa, hot dip alloy of 55% Aluminium 43.5% Zinc 1.5% Silicon and finished with resin coat on both surfaces @ 150 gm/sqm of coating (total both surfaces) as in roof covering/ cladding to wall, fixed with self tapping screws complete all as specified.

M&L for Mild steel Gde Fe-410-W joist, channel, angle or tee sections, fixed independently with out connceting plates, etc. (cut to ordinary lengths i.e. with in 20mm of the length indicated), 'A' quality, complete all as specified.

S&F steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I.S 1161-1979 grade St. 240 including painting structural steel with one shop coat of zinc chromate primer paint (including preparation of surface) at contractor's workshop before fabrication, complete all as specified and directed.

S&F Rolled mild steel in plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, with out any attachment, of Fe-410-W (Gde-E-250) quality A complete all as specified and directed.

S&F Mild screw bolts (Machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, exc 22.5 but n exc 30cm long and 16 to 20mm dia. of shank complete all as specified.

M&L for preparation of new steel surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamelled paint over one coat of red oxide Zinc chrome primer complete all as specified.

Taking down cement plaster on brick or stone walls etc. including racking out joints, hacking for key, scrubbing down with water, any description etc. and removing of the rubbish outside MD land complete all as specified .

M&L for rendering 15mm thick on fair faces of brick work or concrete surfaces, in cement and sand mortar 1:4 top surfaces finished even and smooth without using extra cement complete all as specified.

M&L for preparation of external new surfaces of walls and applying two coats of exterior emulsion paint (weather coat), white or tinted over a coat of exterior primer over and under a coat of wall putty as per manufacturers instructions, complete all as specified.

Providing and fixing in true horizontal level 600mm x 600mm, false ceiling system hot dipped galvanised steel section, exposed surface with pre-coated capping, main tee of size 24 x 38mm, having 0.25mm gauge at every 1200mm centre to centre maximum and rotary stitched cross tee of size 24 x 38mm having 0.25mm gauge at every 600mm c/c and sub cross tee of size 24 x 38mm, having 0.25mm gauge at 1200mm c/c and wall angle of size 19 x 19mm, having 0.35mm gauge fixed to the periphery of the wall. The abovegrid is suspended at every 1200mm c/c in both directions using 3.0mm thick pre-straightened GI wire. laying 595 x 595 x 4mm thick E-Board Designer ceiling fixing 600mm x 60mm x 6mm grid (Frame work), complete all as specified.

M&L for Brick work with fly ash (modular) bricks, straight or curved on plan exc 6m mean radius, built in built in cement and sand mortar 1:4 complete all as specified.

M&L for broken stone or boulder hardcore of gauge n exc. 63mm, deposited, spread and levelled in layer n exc. 15 cm thick, watered and rammed to a true surface complete all as specified.

M&L for plain cement concrete 1:4:8 type D2 using 40mm graded crushed stone aggregate as in foundations filling mass concrete complete all as specified.

M&L for Plain cement concrete 1:2:4 type B0, using 12.5mm graded crushed stone aggregate, 25mm thick as in sub floor complete all as specified.

M&L for Machine cut Kota stone slab flooring 20-25mm thick over and including 15mm thick in CM 1:4 cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing to give mirror finish complete all as specified.

M&L for machine cut Kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar laid over 10mm thick in cement and sand mortar mix 1:3 screed and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing to give mirror finish complete all as specified.

S&F Polycarbonate sheet (Transparent) plain or corrugated 10mm thick as in roof covering/ cladding to wall, fixed with necessary self tapping screws, aluminium sheet complete all as specified.

Surface excavation not exceeding 30 cm deep and averaging 15 cm deep and getting out in any hard/ dense soil surfaces formed to required slope, gradient, camber, and superelevation etc. complete all as specified.

Excavating in trenches, not exceeding 1.5 m wide but not exceeding 1.5 m in depth; for foundations etc. or for shafts, well cess pits, manholes,pier holes,etc. not exceeding 10 qm on plan but not exceeding 1.5 m in depth and getting out in hard/ dense soil complete all as specified.

M&L for Treating the top surface of filled earth at the rate of 5 lires of emulsion per square metre of surface complete all as specified.

M&L for Treating the soil under plinth protection at the rate of 5 litres of emulsion per square of surface area complete all as specified.

M&L for Treating the soil along with internal periphery at the rate of 2.25 litres of emulsion per meter of surface complete all as specified.

M&L for Treating the soil along with external periphery at the rate of 2.25 litres of emulsion per meter of surface complete all as specified.

Returning, filling in, including spreading, levelling, watering and well ramming in layer not exceeding 25 cm thick in hard/ dense soil complete all as specified.

Removing excavated material (soils) etc. exceeding 1.5 KM and and not exceeding 5 KM depositing where directed at a level not exceeding 1.5 m above the starting point complete all as specified.

M&L for Reinforced Cement concrete 1:1.5:3 type A1 using 20mm graded stone aggregate as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc; basement slabs, under reamed piles and mass concrete complete all as specified.

M&L for Reinforced Cement concrete 1:1.5:3 type A1 using 20mm graded stone aggregate as in columns, pillras etc. Complete all as specified.

M&L for Reinforced Cement concrete 1:1.5:3 type A1 using 20mm garded stone aggregate as in beams, cantilevers, bressumers, lintels over 1.5 m span complete all as specified.

M&L for Mild steel TMT bars 10mm dia and over as in reinforcement, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90mm dia. or higher complete all as specified.

M&L for Mild steel TMT bars 6mm dia. and over up to and including 10mm dia. stirrups, spacers and binders as in reinforcement, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90mm dia. Or securing with clips complete all as specified.

Use and waste of formwork to fair surfaces of sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter surfaces finished fair in forms complete all as specified.

Use and waste of Formwork to sides of Square, rectangular or polygonal pillars, posts, struts, piers, columns and stanchions surfaces finished fair as per clause 4.11.16.2 (a) of SSR Part-I complete all as specified.

Use and waste Formwork to flat sides and soffits of floor or roof beams, beam haunchings, girders, bresumers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams etc. surfaces finished fair complete all as specified.

M&L for moorum/ red bajri filling in floors or pavings/ trenches laid in layers not excd 25 cm thick spread, levelled and blinded with earth and rammed including watering complete all as specified.

M&L for Machine cut cudappah stone slab 20-25mm thick over and including 15mm thick in CM 1:6 over cement screed base, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified.

M&L for 16 -18mm thick Granite stone slab of approved colour (of any type) work (table rubbed and polished to mirror finish) in steps, jambs, pillars, window cills, cooking plateforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over and including 15mm thick screeding in CM 1:6 complete all as specified.

M&L for rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations, complete all as specified.

M&L for Non Skid ceramic coloured tiles area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screeding in CM 1:6 complete all as specified.

M&L for glazed Ceramic coloured tiles, size 300mm x 450mm x 7 to 8mm thick in dado/ skirting etc. set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match over and including 10mm thick screeding in CM 1:4 complete all as specified.

M&L for Plain cement concrete type B2 (1:2:4), using 40mm graded crushed stone aggregate, 75mm thick, as in plinth protection, floor finished even and smooth with out using extra cement, joints filled in with bitumen 85/25 grade, complete all as specified.

M&L for Brick work with fly ash (modular) bricks, straight or curved on plan exc 6m mean radius, built in built in cement and sand mortar 1:6 complete all as specified.

M&L for rendering 15mm thick on fair faces of brick work or concrete surfaces, in cement and sand mortar 1:6, top surfaces finished even and smooth without using extra cement complete all as specified.

M&L for preparation of newly plastered/ unplastered surfaces of walls by applying Wall care white (Putty) and sand papering surfaces to achieve smooth surfaces and distempering with distemper oil emulsion, two coats, white or tinted over a coat of alkaline resistant primer including washing floors, cleaning glass, joinery, electrical fittings, wiring etc., of drops and splashes complete all as specified.

S&F Vitreous China urinal half stall, white with grating and union for discharge pipe (excluding flushing cistern, flush pipe, and waste pipe), including connections to flushing pipe and outgoing pipes complete all as specified.

S&F CP Brass urinal spreader including unions and fixed with 15mm bore pipe complete all as specified.

S&F vitreous china wash basin (WHB), ivory, under counter size 560 x 410 x 180mm including CI cantilever brackets, brass Chromium plated waste fittings with long screw shanks and fly nuts, flange end embedded in red lead cement, 32mm NB LDPE water pipe, including cutting for and pinning in ends of brackets or erecting stand, complete all as specified

S&F Chromium plated central hole wash basin mixer Brass hot and cold mixer suitable for 15mm nominal bore pipe with two inlet holes and one outlet hole complete all as specified.

S&F Brass chromium plated bottle traps 300mm (12") Designer wall connection pipe and wall flange complete all as specified.

S&F PTMT connections 15mm size with PTMT nuts of length 450mm complete all as specified.

S&F Chromium plated towel rail 600mm long fixed with SS screws and wooden/ plastic cleats, complete all as specified.

S&F CP mild steel gratings suitable for 100mm dia, complete all as specified.

S&F SS Liquid soap container/ dispenser fixed with and including CP brass screws and wooden/ plastic cleats complete all as specified.

S&F CP Stop/ Angle cock long thread with wall flange, fancy type screwed down for 15mm bore dia. pipe, high pressure, with crutch handle, screwed externally both ends for unions etc. and fixed complete all as specified.

S&F Fancy type Bib taps, CP, cast copper alloy with crutch or butterfly handle, screwed down, scrwed for iron pipe or for brass ferrule and fixed 15mm bore complete all as specified.

S&F stainless steel soap dish fixed in walls complete all as specified

Cutting chases in brick work, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills,sunshades, shelves, lintels, etc. and cutting chases for concealed water tubing or concealed conduit wiring, etc.,and making good, cutting not exc 20 cm girth complete all as specified.

S&F steel water tubing 15mm bore with screwed and socket joints, medium grade, galvanised (including short lengths) with and including all fittings, such as sockets, bends, elbows, unions, tees, diminishing pieces etc. fixed to walls or ceiling or laid in floors complete all as specified.

S&F steel water tubing 20mm bore with screwed and socket joints, medium grade, galvanised (including short lengths) with and including all fittings, such as sockets, bends, elbows, unions, tees, diminishing pieces etc. fixed to walls or ceiling or laid in floors complete all as specified.

S&F Powder coating anodised aluminium ventilator, half portion of the ventilator covered with 5.5mm thick frosted glasses and half portion fittted with frosted louvers and outer side fitted with mosquito proof galvanised wiremess incl all fitting, fitted with aluminium anodised beads, securing on outer face of frame complete all as speified.

S&F Rotational moulded poly-ethylene multilayer water storage tanks (ISI marked) (cylinderical vertical with closed top) 1000 litres capacity, hoisted and fixed in position complete all as specified.

S&F Gunmetal, globe or gate valves, with iron wheel head, screwed both ends for 20mm bore dia. iron pipe and fixed complete all as specified.

S&F 150mm bore DWC sewage pipe SN-8 as per IS 16908 Part-II 2013 laid in trench, jointed and tested as per manufacturer instruction, complete all as specified.

M&L for Plain cement Concrete (1:3:6) type C2 (using 40mm graded stone aggregate) bed to 150mm bore drain pipes including packing under, and haunching against the sides of pipes after they are laid and tested; in complete all as specified.

M&L for Plain cement concrete 1:3:6, type C2, using 40mm graded crushed stone aggregate, 100mm thick as in sub base complete all as specified.

M&L for Plain cement concrete type B1 (1:2:4), using 12.5mm graded crushed stone aggregate as in surface Channels and drains including necessary use and waste of formwork complete all as specified.

M&L for Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/ stopped ends etc. complete all as specified.

S&F 75mm bore PVC (SWR) pipes single socketed ISI marked IS-13592, type 'B in any length (including short lenghts) with rubber ring joints fixed to walls complete all as specified.

S&F 75mm bore PVC (SWR) pipes single socketed ISI marked IS-13592, type 'B' in any length with rubber ring joints laid in trenches or in floors type complete all as specified.

S&F PVC (SWR) bends (ISI marked) 75mm bore complete all as specified

S&F PVC (SWR) junction single, (Single T) equal or unequal (ISI marked) 110mm bore complete all as specified.

S&F PVC (SWR) floor trap, plain with grating including jointing with solvent cement, 75mm dia. outlet complete all as specified.

M&L for 60mm thick, M-35 grade PCC interlocking tiles (rubber moulded and colour chemical coated) of size and shape as approved (ISI- marked), laid over 25mm thick dry sand cushion interstices filled in floors/ pathway and filling outer edges with PCC 1:2:4 type B0 upto full thickness of tiles complete all as specified. (Rate quoted shall deem to be included for filling sand cushion and outer edges with PCC).

M&L for rolled sections/ hollow tube section as in post and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates, complete all as specified.

M&L for mild steel framed work such as grills, gratings, etc., with ends of bars shouldered and/ or riveted, or forged in to spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; frame work of water tanks and similar work conforming to Fe-290 Gde E-165 complete all as specified.

M&L for Reinforced Cement concrete in cement concrete mix 1:1.5:3 type A1 using (20mm graded stone aggregate) slabs supported on walls, beams and columns, in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified.

M&L for Reinforced cement concrete type A1, 1:1.5:3 using (20mm graded stone aggregate) as in chajjas complete all as specified.

Use and waste of form work roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) surfaces finished fair as specified in SSR Part-I Clause 4.11.16.2 (a) as specified complete all as specified.

Use and waste of formwork to chullah hoods, chajjas, weather shades, corbels, water troughs and similar items including edges finished fair as per clause 4.11.16.2 (a) of SSR Part-I complete all as specified.

M & L for 100mm thick PCC 1:4:8 Type D-2 (using 40mm graded stone aggregate) as in base/ sub base complete all as specified.

M&L for 50mm thick PCC 1:2:4 Type B-2 (using 20mm graded stone aggregate) as in floor top surfaces finished even and smooth without using extra cement complete all as specified and directed.

M&L for Non Skid ceramic coloured tiles 7 to 8mm thick (square/ rectangular) area of each tile exceeding 0.18 sqm but not exceeding. 38sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match. over 15mm thick screeding in CM 1:6 complete all as specified (screed bed shall not be measured and paid separately).

M&L for Brickwork with fly ash (modular) bricks, straight or curved on plan to any radius in half brick thick walls, built in cement and sand mortar 1:4 complete all as specified.

M&L for rendering 15mm thick on fair faces of brick work or concrete surfaces, in cement and sand mortar 1:4 mixed with water proofing compound as per manufacturer's instructions, top surfaces finished even and smooth without using extra cement complete all as specified. (Note:- water proofing compound shall be measured and paid separately under appropriate item)

M&L for rendering 5mm thick on concrete surfaces in ceiling, in cement and sand mortar 1:4 top surfaces finished even and smooth without using extra cement complete all as specified

M&L for rendering 20mm thick on RCC roof top surfaces, in cement and sand mortar 1:4 mixed with water proofing compound complete all as specified top surfaces finished even and smooth without using extra cement complete all as specified (WPC shall be measured and paid separately).

Supply only Integral water proofing compound (Liquid) complete all as specified.

M&L for preparation of new plastered surfaces of walls and distempering with distemper oil emulsion, two coats, white or tinted over a coat of alkaline resistant primer including washing floors, cleaning glass, joinery, electrical fittings, wiring etc., of drops and splashes complete all as specified.

M&L for two coats of exterior emulsion paint (Apex), white or tinted on new surfaces of walls including washing floors, cleaning glass, joinery, electrical fittings, wiring etc., of drops and splashes complete all as specified.

S&F solid PVC door frame of size 50mm x 47mm made out of 5mm wood grain printed PVC sheet reinforced with Mild steel square tube complete all as specified and directed.

S&F factory made solid PVC moulded door shutters with wood free EPS, 30mm thick (stiles) with 6 raised panels design with 2mm thick Moulded PVC Sheet on the front face and 2mm Plain colour PVC sheet on back face, supply-ing & fixing in frame at site as per specification & draw-ing complete all as specified.

S&F Aluminium, anodised, barrel tower bolts of extruded section and fixed, 150mm length of bolt, ISI marked complete all as specified.

S&F 300mm long Aluminium alloy anodised, sliding door bolt with hasp, staple (bolt type) ISI marked and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified.

S&F Aluminium handles, cast type anodised, 150mm long complete all as specified.

S&F butt Hinges, medium weight, cold rolled mild steel, 100mm size complete all as specified.

S&F Vitreous China white wash down water closet (padestal pattern), including fixing bolts, plastic closet seat, black, closed pattern with recessed bottom and cover and mild steel CP hinging device, including connection to drain pipe, and to flushing pipe and antisyphonic pipe etc. complete all as specified.

S&F Low level flushing cistern, 10 ltr capacity, PVC valveless syphonic action type, white with inlet, ball valve, float valve and handle, flush pipe, iincluding provision of 32mm dia PVC flush pipe and making connections, complete all as specified and directed.

S & F PTMT connections 15mm size with PTMT nuts of length 450mm complete all as specified.

S&F Chromium plated towel ring, fixed with and including Chromium plated brass screws and wooden/ plastic cleats, complete all as specified.

S&F anodised Aluminium alloy sections sliding windows shutters with frames (consisting 2 No glazed shutters and 01 No gauge shutter) Series-D (25mm), 3 track sliding shutters duly fitted with neoprene beading, glazing clips, locking device, heat absorbing glass 4.8mm nominal thickness, and stainless steel wire cloth of 0.25mm dia of wire and 1.15mm width of aperture, aluminium alloy handles etc. complete all as specified.

S&F Rotational moulded poly-ethylene multilayer water storage tanks (cylinderical vertical with closed top), 1000 litres capacity, tripple layered (ISI marked), hoisted incl Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic ball, suitable for 20mm bore pipe, screwed for iron pipeand fixed in position complete all as specified.

Supply & providing water proofing roof treatment with polymeric standard water proofing membrane, having 10 years gurantee for water tightness complete all as specified and described as under:- (a) Preparation of RCC roof surface and applying one coat of polymeric modified bitumen 85/25 @ 1.2Kg/Sqm over a coat of polymeric primer @ 0.30 Kg/sqm including cleaning surface all as per manufaturer's specification complete all as specified and directed. (b) Supply & providing water proofing with 3mm thick APP polymeric proofing membran of 3Kg/Sqm HYPERPLAS STANDARD/ MULTIPLAS STANDARD consisting of 100micron HMHDPE film centre core including coating the surface with compatible primer and torch application of membrane with 10cm overlaps as required thereof, complete all as specified and directed. (c) Aluminium bituminous paint @1.10 Kg/Sqm shall be applied over the APP membrane surface. Note:- The work of water proofing treatment shall be got executed through expert team of manufacturers or authorised applicator of manufacturer, complete all as specified and directed.

S&F two way Angle cock long thread with wall flange, fancy type screwed down for 15mm bore dia. pipe, high pressure, with crutch handle, screwed externally both ends for unions etc. and fixed complete all as specified.

S&F Health faucet with 1 metre extendable metal tube and holder complete all as specified

S&F 110mm bore PVC (SWR) pipes single socketed ISI marked IS-13592, type 'B in any length with rubber ring joints fixed to walls complete all as specified.

S&F 110mm bore PVC (SWR) pipes single socketed ISI marked IS-13592, type 'B' in any length with rubber ring joints laid in trenches or in floors type complete all as specified.

S&F PVC (SWR) bends (ISI marked) 110mm bore complete all as specified.

S&F PVC (SWR) vent cowl 110mm bore complete all as specified.

M&L for Point wiring with 1.5 Sqmm (nominal cross sectional area), single core, PVC insulated with multistranded PVC unsheathed FRLSH copper conductor cable in and including rigid non- metallic PVC surface conduit/ casing caping of suitable size medium grade ISI marked complete, including one continuity earth wire of PVC insulated, unsheathed 1.5 Sqmm (nominal cross sectional area) FRLSH copper conductor connected to all fittings, common earth and connected to earth dolly including modular GI sheet metal/ PVC flush box, covered with modular white cover plate with inner frame suitable for modular switches and blank plates of suitable size all fittings and accessories and making good disturbed surface of walls and floors etc. complete all as specified and directed for the following:- Note:- Make of modular GI sheet metal/ PVC box should be same with switch/ socket.

(a) One light/ fan point controlled by one switch, complete all as specified.

(b) One switch/ socket outlet point 2/3 pin 5 Amp multipurpose on independent board, complete all as specified

(c) One socket outlet 2/3 pin 5 Amp, multipurpose on same board with other switch, complete all as specified

M&L for Point wiring with 2.5 Sqmm (nominal cross sectional area), single core, PVC insulated with multistranded PVC unsheathed FRLSH copper conductor cable in and including rigid non-metallic PVC concealed conduit of suitable size medium grade ISI marked complete including one continuity earth wire of PVC insulated, unsheathed 2.5 Sqmm (nominal cross sectional area) FRLSH copper conductor connected to all fittings, common earth and connected to earth dolly for one three pin 15/16 Amps socket out-let point on an independent board including modular flush box, covered with modular white cover plate with inner frame suitable for modular switches and blank plates of suitable size incl taking down carefully copper/ alluminium power point wiring switches, sockets and making good disturbed surface of walls and floors etc. complete all as specified and directed Note:- Make of modular GI sheet metal/ PVC box should be same with switch/ socket.

S&F Ceiling rose three terminals surface bakelite type, AC, 50 HZ, 230V, complete all as specified

S&F Modular switch 1 way 6 A, 1 module complete all as specified.

S&F Modular socket 6 Amps 2/3 pin combined 2 module complete all as specified.

S&F Switch modular type 16 A, 1 module complete all as specified

S&F Socket modular type multipurposes 6/16 A, 2 module complete all as specified

S & F for LED luminaire 2 x 2 ft (size 600 x 600mm) square LED panel 35/36 watts, 220 volts, AC recessed/ surface mounted type with high efficiency PMMA diffuser soft glare free light complete with drivers, holders, LED lamp suitable for roof ceiling, including connecting up with driver three core flexible copper conductor cases of suitable size complete all as specified.

S&F MCB DB SPN 8 way double door with 200 Amps rated bus bar, 230 volts, 50 Hz including necessary provision for inserting the DBs in wall by cutting the brick/ stone masonary etc and making good of distrubed surface to match with existing colour of wall complete all as specified.

S&F rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) of SPN 32 Amps and current carrying capacity in the MCB DBncluding connection with using suitable size aluminium/ copper lugs complete all as specified.

S&F rating 240V 10 KA 'B' curve miniature circuit breaker (MCB) of single poles and current carrying capacity 5 to 32 Amp, in the MCB DB ncluding connection with using suitable size aluminium/ copper lugs complete all as specified.

M&L for sub main wiring with 02 runs of 6 Sqmm main wire along with 01 run of 06 Sqmm earth wire (green in colour) single core FRLSH PVC insulated, unsheathed, multi-stranded, 1100 volts grade ISI marked copper conductor cable, drawn through and including adequate size rigid non-metallic PVC concealed/ surface conduit (medium grade) wherever necessary with all fittings & accessories including cutting chases for conduits as required, sinking for terminal boxes, making good the same complete all as specified Note:- Two runs of main copper conductor, one run of earth wire and one run of PVC conduit shall be measured as one unit length.

S&F ceiling fans complete with blades, down rods, electronic regulator and remote with battery and accessories, 230 V, 1200mm sweep. Min air delivery 210 CFM with service value not less than 8.46 BEE with down road 15mm/12mm upto 2.5 mtr. Five star rated with brushless direct current motor (BLDC) including writing the MES number with synthetic enamel paint complete all as specified and directed. Note:- Rate of electronic regulator and remote with battery shall be deemed to be incl in the quoted rate.

S & F Galvanised, steel rod 16/15mm diameter and length from 0.5 meter to 2.5 metres as per site requirement complete all as specified.

S&F lamp holder insulated body with back plate for batten fittings complete all as specified.

S&F LED bulb of 7 watt, of base B-22, 6500 K suitable for fixing in lamp holder complete all as specified.

S&F Inverter LED batten 20 watt with squre profile and polycarbonate channel. Lithium lon battery with charging time 8 hourse -10 hourse and back up time upto 4 hours. with extruded environmental friendly, energy efficient with three core flexible copper conductor cable of suitable size from ceiling rose complete with all connected accessories complete all as specified.

S & F for Energy saving new generation environmental friendly long life versatile LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete including necessary mounting arrangements and provision of 2.5 Sqmm three core copper conductor cable multi stranded from ceiling rose to light fitting and necessary dia GI pipe medium grade bracket 1.5 mtr long bend to required shape with clamps, nut, bolts complete all as specified.

S&F MCB DB SPN 4 way double door with 200 Amps rated bus bar, 230 volts, 50 Hz including necessary provision for inserting the DBs in wall by cutting the brick/ stone masonary etc and making good of distrubed surface to match with existing colour of wall complete all as specified.

S&F exhaust fan, steel body AC single phase 230 volt of size 300mm sweep complete with blade, frame and louvers and mesh wire complete all as specified and directed incl making/ alteration of hole wherever necessary and making good disturbed surface, painting to match with existing surfaces.complete all as specified.

Sppply & Laying XLPE insulated, armoured, electric cable of size 6 Sqmm 2 core with aluminium conductor, 1100 volts grade, laid in trenches, fixed on poles/ walls or passing through pipes including provision of necessary lugs and glands & making necessary connection complete all as specified.

Excavation in trenches not exc. 1.5m wide and not exc 1.5m deep in any type of soil and getting out complete all as specified and directed by Engr-in-Charge.

M&L for filling approved fine river sand in trenches as cable cushion to the full width of excavated trench, under and over cable complete all as specified and as directed. (Note : Punned thickness of sand shall be measured)

M&L for bricks slightly over burnt (kiln burnt), modular bricks, best quality, locally available, laid flat, dry, laid in trenches along the length of cable transvarsally with width equal to length of brick for cable protection complete all as specified and as directed.

S&F and jointing GI pipe 'light grade' 25mm bore in trenches/ under floors or roads/ along poles/ on wall incl clamps for protection of cables incl fittings and making good of disturbed road to match with existing road complete all as specified and directed.

Drilling and tapping cast iron water mains (in position) for branch connections of the internal dia 40/50mm and connection tee of suitable size, complete all as specified.

M&L for sub main wiring with 02 runs of 2.5 Sqmm main wire along with 01 run of 2.5 Sqmm earth wire (green in colour) single core FRLSH PVC insulated, unsheathed, multi-stranded, 1100 volts grade ISI marked copper conductor cable, drawn through and including adequate size rigid non-metallic PVC concealed/ surface conduit (medium grade) wherever necessary with all fittings & accessories including cutting chases for conduits as required, sinking for terminal boxes, making good the same complete all as specified. Note:- Two runs of main copper conductor, one run of earth wire and one run of PVC conduit shall be measured as one unit length.

Sppply & Laying XLPE insulated, armoured, electric cable of size 10 Sqmm 2 core with aluminium conductor, 1100 volts grade, laid in trenches, fixed on poles/ walls or passing through pipes including provision of necessary lugs and glands & making necessary connection complete all as specified.

Supply and fixing 10W LED 6500K lights fitting Decorative ultra slim square profile LED lighting fixture with extruded polycarbonate, environmental friendly, energy efficient with three core flexible copper conductor cable of suitable size from ceiling rose complete with all connected accessories complete all as specified and directed.

RK CONSTRUCTION (BID ID -3315359)

SANJAY ENTERPRISES (BID ID -3309401)