REPAIR REPLACEMENT TO POWER DISTRIBUTION LT PANELS AND ALLIED WORKS AT 512 ABW UNDER AGE EM II IN GE CENTRAL KIRKEE

Amount

Dismantling and Taking out old unserviceable feeder pillar/panel boards including discnnecting and removing of all incoming and out going cables gland lugs/thimbles, etc carefuly so that same can be reused with new panels with all connecting accessories and making good to the disturbed wall / floor surface and painting the same with matching paint as of existing wall including material all as specified and directed by Engineer in charge.

Supply, fixing, commissioning and testing LT Distribution panel board (With 50 KA RMS for 1 sec CPRI approved) made out of 2mm thick CRCA sheet for laod bearing members and 1.6 mm thick CRCA sheet for non-load bearing members duly powder coated, RAL 7035 (Siemens gray) with seven tank pre-treatment confirming to IS 8623, in door type with IP 43 protection, totally enclosed weather dust and vermin proof with a single front and rear opening, 415V, 3 phase, 4 wire, AC, 50Hz having aluminium bus bar insulated with PVC sleeves coloured in RYB complete with internal wiring with copper conductor, and foundation with thick angle iron frame grouted in PCC 1:3:6 not less that 0.6 mtrs from ground level or as directed complete suitable for and including of following items (all panels should be with digital multifunctional meters and LED indicating lamps for incoming. All MCCBs (Thermal magnetic and mictoprocessor based ) should be adjustable with Icu= Ics 100% and should be with suitable extended rotary hangle and spreader links at both side. All incoming & outgoing cable entries from bottom and incoming and outgoing cables to be fixed on concreate based or in cable ducts or fixed on wall as per site requirement. Note: 1 .. Drawing should be approved by Engr-in-Charge before manufacturing . Two stage inspection of manufacturing i.e. fabrication before powder coating & during swith gear installation, inspection /factory visit of Engg-in-Charge is compulsory to be arranged by contractor at no extra cost. 3. Contractor should visit the site to understand the scope of work before quoting the tender.

INCOMER : MCCB FP, 25 kA, 200 AMPS with thermal magnetic release, Ics = 100% Icu, Adjustable Over Load setting: 0.8 -1.0 x In, with spreader links , insulating shields and vary depth rotary handle Make - Legrand, Cat No. - 4202 18 /L&T /ABB/

OUTGOINGS a) MCCB FP, 25 kA, 100 AMPS with thermal magnetic release, Ics = 100% Icu, Adjustable Over Load setting: 0.8 -1.0 x In, with spreader links , insulating shields and vary depth rotary handle Make - Legrand, Cat No. - 4200 55 /L&T /ABB

b) MCCB FP, 25 kA, 63 AMPS with thermal magnetic release, Ics = 100% Icu, Adjustable Over Load setting: 0.8 -1.0 x In, with spreader links , insulating shields and vary depth rotary handle Make - Legrand, Cat No. - 4200 53 /L&T /ABB

c) MCB four pole 20 to 32 Amps, 415 volts, 10 kA breaking capacity, 'C' curve Make Legrand Ct No 4086 78-80 /L&T /ABB

All as per Item No.02 above but suitable for and including following accessories :

INCOMER : MCCB FP, 36 kA, 400 AMPS with thermal magnetic release, Ics = 100% Icu, Adjustable Over Load setting: 0.8 -1.0 x In, with spreader links , insulating shields and vary depth rotary handle Make - Legrand, Cat No. - 4220 07 /L&T /ABB

OUTGOINGS a) MCCB FP, 25 kA, 160 AMPS with thermal magnetic release, Ics = 100% Icu, Adjustable Over Load setting: 0.8 -1.0 x In, with spreader links , insulating shields and vary depth rotary handle Make - Legrand, Cat No. - 4200 57 /L&T /ABB

b) MCCB FP, 25 kA, 100 AMPS with thermal magnetic release, Ics = 100% Icu, Adjustable Over Load setting: 0.8 -1.0 x In, with spreader links , insulating shields and vary depth rotary handle Make - Legrand, Cat No. - 4200 55 /L&T /ABB

c) MCCB FP, 25 kA, 63 AMPS with thermal magnetic release, Ics = 100% Icu, Adjustable Over Load setting: 0.8 -1.0 x In, with spreader links , insulating shields and vary depth rotary handle Make - Legrand, Cat No. - 4200 53 /L&T /ABB

d) MCB four pole 20 to 32 Amps, 415 volts, 10 kA breaking capacity, 'C' curve Make Legrand Ct No 4086 78-80 /L&T /ABB

All as per Item No.02 above but suitable for and including following accessories :

INCOMER : MCCB FP, 25 kA, 250 AMPS with thermal magnetic release, Ics = 100% Icu, Adjustable Over Load setting: 0.8 -1.0 x In, with spreader links , insulating shields and vary depth rotary handle Make - Legrand, Cat No. - 4202 19 /L&T /ABB

OUTGOINGS a) MCCB FP, 25 kA, 200 AMPS with thermal magnetic release, Ics = 100% Icu, Adjustable Over Load setting: 0.8 -1.0 x In, with spreader links , insulating shields and vary depth rotary handle Make - Legrand, Cat No. - 4202 18 /L&T /ABB/

b) MCCB FP, 25 kA, 100 AMPS with thermal magnetic release, Ics = 100% Icu, Adjustable Over Load setting: 0.8 -1.0 x In, with spreader links , insulating shields and vary depth rotary handle Make - Legrand, Cat No. - 4200 55 /L&T /ABB

c) MCCB FP, 25 kA, 63 AMPS with thermal magnetic release, Ics = 100% Icu, Adjustable Over Load setting: 0.8 -1.0 x In, with spreader links , insulating shields and vary depth rotary handle Make - Legrand, Cat No. - 4200 53 /L&T /ABB

All as per Item No.02 above but suitable for and including following accessories :

INCOMER : MCCB FP, 25 kA, 250 AMPS with thermal magnetic release, Ics = 100% Icu, Adjustable Over Load setting: 0.8 -1.0 x In, with spreader links , insulating shields and vary depth rotary handle Make - Legrand, Cat No. - 4202 19 /L&T /ABB

OUTGOINGS a) MCCB FP, 25 kA, 100 AMPS with thermal magnetic release, Ics = 100% Icu, Adjustable Over Load setting: 0.8 -1.0 x In, with spreader links , insulating shields and vary depth rotary handle Make - Legrand, Cat No. - 4200 55 /L&T /ABB

b) MCCB FP, 25 kA, 63 AMPS with thermal magnetic release, Ics = 100% Icu, Adjustable Over Load setting: 0.8 -1.0 x In, with spreader links , insulating shields and vary depth rotary handle Make - Legrand, Cat No. - 4200 53 /L&T /ABB

All as per Item No.02 above but suitable for and including following accessories :

INCOMER : MCCB FP, 25 kA, 250 AMPS with thermal magnetic release, Ics = 100% Icu, Adjustable Over Load setting: 0.8 -1.0 x In, with spreader links , insulating shields and vary depth rotary handle Make - Legrand, Cat No. - 4202 19 /L&T /ABB

OUTGOINGS a) MCCB FP, 25 kA, 100 AMPS with thermal magnetic release, Ics = 100% Icu, Adjustable Over Load setting: 0.8 -1.0 x In, with spreader links , insulating shields and vary depth rotary handle Make - Legrand, Cat No. - 4200 55 /L&T /ABB

b) MCCB FP, 25 kA, 63 AMPS with thermal magnetic release, Ics = 100% Icu, Adjustable Over Load setting: 0.8 -1.0 x In, with spreader links , insulating shields and vary depth rotary handle Make - Legrand, Cat No. - 4200 53 /L&T /ABB

c) MCB four pole 20 to 32 Amps, 415 volts, 10 kA breaking capacity, 'C' curve Make Legrand Ct No 4086 78-80 /L&T /ABB

All as per Item No.02 above but suitable for and including following accessories :

INCOMER : MCCB FP, 25 kA, 250 AMPS with thermal magnetic release, Ics = 100% Icu, Adjustable Over Load setting: 0.8 -1.0 x In, with spreader links , insulating shields and vary depth rotary handle Make - Legrand, Cat No. - 4202 19 /L&T /ABB

OUTGOINGS a) MCCB FP, 25 kA, 100 AMPS with thermal magnetic release, Ics = 100% Icu, Adjustable Over Load setting: 0.8 -1.0 x In, with spreader links , insulating shields and vary depth rotary handle Make - Legrand, Cat No. - 4200 55 /L&T /ABB

b) MCCB FP, 25 kA, 63 AMPS with thermal magnetic release, Ics = 100% Icu, Adjustable Over Load setting: 0.8 -1.0 x In, with spreader links , insulating shields and vary depth rotary handle Make - Legrand, Cat No. - 4200 53 /L&T /ABB

c) MCB four pole 20 to 32 Amps, 415 volts, 10 kA breaking capacity, 'C' curve Make Legrand Ct No 4086 78-80 /L&T /ABB

All as per Item No.02 above but suitable for and including following accessories :

INCOMER : MCCB FP, 25 kA, 250 AMPS with thermal magnetic release, Ics = 100% Icu, Adjustable Over Load setting: 0.8 -1.0 x In, with spreader links , insulating shields and vary depth rotary handle Make - Legrand, Cat No. - 4202 19 /L&T /ABB

OUTGOINGS a) MCCB FP, 25 kA, 100 AMPS with thermal magnetic release, Ics = 100% Icu, Adjustable Over Load setting: 0.8 -1.0 x In, with spreader links , insulating shields and vary depth rotary handle Make - Legrand, Cat No. - 4200 55 /L&T /ABB

b) MCCB FP, 25 kA, 63 AMPS with thermal magnetic release, Ics = 100% Icu, Adjustable Over Load setting: 0.8 -1.0 x In, with spreader links , insulating shields and vary depth rotary handle Make - Legrand, Cat No. - 4200 53 /L&T /ABB

c) MCB four pole 20 to 32 Amps, 415 volts, 10 kA breaking capacity, 'C' curve Make Legrand Ct No 4086 78-80 /L&T /ABB

All as per Item No.02 above but suitable for and including following accessories :

INCOMER : MCCB FP, 25 kA, 100 AMPS with thermal magnetic release, Ics = 100% Icu, Adjustable Over Load setting: 0.8 -1.0 x In, with spreader links , insulating shields and vary depth rotary handle Make - Legrand, Cat No. - 4200 55 /L&T /ABB

OUTGOINGS a) MCCB FP, 25 kA, 63 AMPS with thermal magnetic release, Ics = 100% Icu, Adjustable Over Load setting: 0.8 -1.0 x In, with spreader links , insulating shields and vary depth rotary handle Make - Legrand, Cat No. - 4200 53 /L&T /ABB

b) MCB four pole 20 to 32 Amps, 415 volts, 10 kA breaking capacity, 'C' curve Make Legrand Ct No 4086 78-80 /L&T /ABB

All as per Item No.02 above but suitable for and including following accessories :

INCOMER : MCCB FP, 25 kA, 160 AMPS with thermal magnetic release, Ics = 100% Icu, Adjustable Over Load setting: 0.8 -1.0 x In, with spreader links , insulating shields and vary depth rotary handle Make - Legrand, Cat No. - 4200 57 /L&T /ABB

OUTGOINGS a) MCCB FP, 25 kA, 100 AMPS with thermal magnetic release, Ics = 100% Icu, Adjustable Over Load setting: 0.8 -1.0 x In, with spreader links , insulating shields and vary depth rotary handle Make - Legrand, Cat No. - 4200 55 /L&T /ABB

b) MCCB FP, 25 kA, 63 AMPS with thermal magnetic release, Ics = 100% Icu, Adjustable Over Load setting: 0.8 -1.0 x In, with spreader links , insulating shields and vary depth rotary handle Make - Legrand, Cat No. - 4200 53 /L&T /ABB

c) MCB four pole 20 to 32 Amps, 415 volts, 10 kA breaking capacity, 'C' curve Make Legrand Ct No 4086 78-80 /L&T /ABB

All as per Item No.02 above but suitable for and including following accessories :

INCOMER : MCCB FP, 25 kA, 250 AMPS with thermal magnetic release, Ics = 100% Icu, Adjustable Over Load setting: 0.8 -1.0 x In, with spreader links , insulating shields and vary depth rotary handle Make - Legrand, Cat No. - 4202 19 /L&T /ABB

OUTGOINGS a) MCCB FP, 25 kA, 100 AMPS with thermal magnetic release, Ics = 100% Icu, Adjustable Over Load setting: 0.8 -1.0 x In, with spreader links , insulating shields and vary depth rotary handle Make - Legrand, Cat No. - 4200 55 /L&T /ABB

b) MCCB FP, 25 kA, 63 AMPS with thermal magnetic release, Ics = 100% Icu, Adjustable Over Load setting: 0.8 -1.0 x In, with spreader links , insulating shields and vary depth rotary handle Make - Legrand, Cat No. - 4200 53 /L&T /ABB

c) MCB four pole 20 to 32 Amps, 415 volts, 10 kA breaking capacity, 'C' curve Make Legrand Ct No 4086 78-80 /L&T /ABB

All as per Item No.02 above but suitable for and including following accessories :

INCOMER : MCCB FP, 25 kA, 100 AMPS with thermal magnetic release, Ics = 100% Icu, Adjustable Over Load setting: 0.8 -1.0 x In, with spreader links , insulating shields and vary depth rotary handle Make - Legrand, Cat No. - 4200 55 /L&T /ABB

OUTGOINGS a) MCB four pole 20 to 32 Amps, 415 volts, 10 kA breaking capacity, 'C' curve Make Legrand Ct No 4086 78-80 /L&T /ABB

All as per Item No.02 above but suitable for and including following accessories :

INCOMER : MCCB FP, 36 kA, 400 AMPS with thermal magnetic release, Ics = 100% Icu, Adjustable Over Load setting: 0.8 -1.0 x In, with spreader links , insulating shields and vary depth rotary handle Make - Legrand, Cat No. - 4220 07 /L&T /ABB

OUTGOINGS a) MCCB FP, 25 kA, 200 AMPS with thermal magnetic release, Ics = 100% Icu, Adjustable Over Load setting: 0.8 -1.0 x In, with spreader links , insulating shields and vary depth rotary handle Make - Legrand, Cat No. - 4202 18 /L&T /ABB/

b) MCCB FP, 25 kA, 100 AMPS with thermal magnetic release, Ics = 100% Icu, Adjustable Over Load setting: 0.8 -1.0 x In, with spreader links , insulating shields and vary depth rotary handle Make - Legrand, Cat No. - 4200 55 /L&T /ABB

All as per Item No.02 above but suitable for and including following accessories :

INCOMER : MCCB FP, 25 kA, 250 AMPS with thermal magnetic release, Ics = 100% Icu, Adjustable Over Load setting: 0.8 -1.0 x In, with spreader links , insulating shields and vary depth rotary handle Make - Legrand, Cat No. - 4202 19 /L&T /ABB

OUTGOINGS a) MCCB FP, 25 kA, 100 AMPS with thermal magnetic release, Ics = 100% Icu, Adjustable Over Load setting: 0.8 -1.0 x In, with spreader links , insulating shields and vary depth rotary handle Make - Legrand, Cat No. - 4200 55 /L&T /ABB

b) MCCB FP, 25 kA, 63 AMPS with thermal magnetic release, Ics = 100% Icu, Adjustable Over Load setting: 0.8 -1.0 x In, with spreader links , insulating shields and vary depth rotary handle Make - Legrand, Cat No. - 4200 53 /L&T /ABB

All as per Item No.02 above but suitable for and including following accessories :

INCOMER : MCCB FP, 25 kA, 160 AMPS with thermal magnetic release, Ics = 100% Icu, Adjustable Over Load setting: 0.8 -1.0 x In, with spreader links , insulating shields and vary depth rotary handle Make - Legrand, Cat No. - 4200 57 /L&T /ABB

OUTGOINGS a) MCCB FP, 25 kA, 63 AMPS with thermal magnetic release, Ics = 100% Icu, Adjustable Over Load setting: 0.8 -1.0 x In, with spreader links , insulating shields and vary depth rotary handle Make - Legrand, Cat No. - 4200 53 /L&T /ABB

b) MCB four pole 20 to 32 Amps, 415 volts, 10 kA breaking capacity, 'C' curve Make Legrand Ct No 4086 78-80 /L&T /ABB

All as per Item No.02 above but suitable for and including following accessories :

INCOMER : MCCB FP, 25 kA, 100 AMPS with thermal magnetic release, Ics = 100% Icu, Adjustable Over Load setting: 0.8 -1.0 x In, with spreader links , insulating shields and vary depth rotary handle Make - Legrand, Cat No. - 4200 55 /L&T /ABB

OUTGOINGS a) MCCB FP, 25 kA, 63 AMPS with thermal magnetic release, Ics = 100% Icu, Adjustable Over Load setting: 0.8 -1.0 x In, with spreader links , insulating shields and vary depth rotary handle Make - Legrand, Cat No. - 4200 53 /L&T /ABB

All as per Item No.02 above but suitable for and including following accessories :

INCOMER : MCCB FP, 25 kA, 250 AMPS with thermal magnetic release, Ics = 100% Icu, Adjustable Over Load setting: 0.8 -1.0 x In, with spreader links , insulating shields and vary depth rotary handle Make - Legrand, Cat No. - 4202 19 /L&T /ABB

OUTGOINGS a) MCCB FP, 25 kA, 100 AMPS with thermal magnetic release, Ics = 100% Icu, Adjustable Over Load setting: 0.8 -1.0 x In, with spreader links , insulating shields and vary depth rotary handle Make - Legrand, Cat No. - 4200 55 /L&T /ABB

b) MCCB FP, 25 kA, 63 AMPS with thermal magnetic release, Ics = 100% Icu, Adjustable Over Load setting: 0.8 -1.0 x In, with spreader links , insulating shields and vary depth rotary handle Make - Legrand, Cat No. - 4200 53 /L&T /ABB

All as per Item No.02 above but suitable for and including following accessories :

INCOMER : MCCB FP, 25 kA, 250 AMPS with thermal magnetic release, Ics = 100% Icu, Adjustable Over Load setting: 0.8 -1.0 x In, with spreader links , insulating shields and vary depth rotary handle Make - Legrand, Cat No. - 4202 19 /L&T /ABB

OUTGOINGS a) MCCB FP, 25 kA, 100 AMPS with thermal magnetic release, Ics = 100% Icu, Adjustable Over Load setting: 0.8 -1.0 x In, with spreader links , insulating shields and vary depth rotary handle Make - Legrand, Cat No. - 4200 55 /L&T /ABB

b) MCCB FP, 25 kA, 63 AMPS with thermal magnetic release, Ics = 100% Icu, Adjustable Over Load setting: 0.8 -1.0 x In, with spreader links , insulating shields and vary depth rotary handle Make - Legrand, Cat No. - 4200 53 /L&T /ABB

All as per Item No.02 above but suitable for and including following accessories :

INCOMER : MCCB FP, 25 kA, 200 AMPS with thermal magnetic release, Ics = 100% Icu, Adjustable Over Load setting: 0.8 -1.0 x In, with spreader links , insulating shields and vary depth rotary handle Make - Legrand, Cat No. - 4202 18 /L&T /ABB/

OUTGOINGS a) MCCB FP, 25 kA, 100 AMPS with thermal magnetic release, Ics = 100% Icu, Adjustable Over Load setting: 0.8 -1.0 x In, with spreader links , insulating shields and vary depth rotary handle Make - Legrand, Cat No. - 4200 55 /L&T /ABB

b) MCCB FP, 25 kA, 63 AMPS with thermal magnetic release, Ics = 100% Icu, Adjustable Over Load setting: 0.8 -1.0 x In, with spreader links , insulating shields and vary depth rotary handle Make - Legrand, Cat No. - 4200 53 /L&T /ABB

All as per Item No.02 above but suitable for and including following accessories :

INCOMER : MCCB FP, 25 kA, 200 AMPS with thermal magnetic release, Ics = 100% Icu, Adjustable Over Load setting: 0.8 -1.0 x In, with spreader links , insulating shields and vary depth rotary handle Make - Legrand, Cat No. - 4202 18 /L&T /ABB/

OUTGOINGS a) MCCB FP, 25 kA, 100 AMPS with thermal magnetic release, Ics = 100% Icu, Adjustable Over Load setting: 0.8 -1.0 x In, with spreader links , insulating shields and vary depth rotary handle Make - Legrand, Cat No. - 4200 55 /L&T /ABB

b) MCCB FP, 25 kA, 63 AMPS with thermal magnetic release, Ics = 100% Icu, Adjustable Over Load setting: 0.8 -1.0 x In, with spreader links , insulating shields and vary depth rotary handle Make - Legrand, Cat No. - 4200 53 /L&T /ABB

c) MCB four pole 20 to 32 Amps, 415 volts, 10 kA breaking capacity, 'C' curve Make Legrand Ct No 4086 78-80 /L&T /ABB

All as per Item No.02 above but suitable for and including following accessories :

INCOMER : MCCB FP, 25 kA, 250 AMPS with thermal magnetic release, Ics = 100% Icu, Adjustable Over Load setting: 0.8 -1.0 x In, with spreader links , insulating shields and vary depth rotary handle Make - Legrand, Cat No. - 4202 19 /L&T /ABB

OUTGOINGS a) MCCB FP, 25 kA, 100 AMPS with thermal magnetic release, Ics = 100% Icu, Adjustable Over Load setting: 0.8 -1.0 x In, with spreader links , insulating shields and vary depth rotary handle Make - Legrand, Cat No. - 4200 55 /L&T /ABB

b) MCCB FP, 25 kA, 63 AMPS with thermal magnetic release, Ics = 100% Icu, Adjustable Over Load setting: 0.8 -1.0 x In, with spreader links , insulating shields and vary depth rotary handle Make - Legrand, Cat No. - 4200 53 /L&T /ABB

All as per Item No.02 above but suitable for and including following accessories :

INCOMER : MCCB FP, 25 kA, 250 AMPS with thermal magnetic release, Ics = 100% Icu, Adjustable Over Load setting: 0.8 -1.0 x In, with spreader links , insulating shields and vary depth rotary handle Make - Legrand, Cat No. - 4202 19 /L&T /ABB

OUTGOINGS a) MCCB FP, 25 kA, 100 AMPS with thermal magnetic release, Ics = 100% Icu, Adjustable Over Load setting: 0.8 -1.0 x In, with spreader links , insulating shields and vary depth rotary handle Make - Legrand, Cat No. - 4200 55 /L&T /ABB

b) MCCB FP, 25 kA, 63 AMPS with thermal magnetic release, Ics = 100% Icu, Adjustable Over Load setting: 0.8 -1.0 x In, with spreader links , insulating shields and vary depth rotary handle Make - Legrand, Cat No. - 4200 53 /L&T /ABB

All as per Item No.02 above but suitable for and including following accessories :

INCOMER : MCCB FP, 36 kA, 400 AMPS with thermal magnetic release, Ics = 100% Icu, Adjustable Over Load setting: 0.8 -1.0 x In, with spreader links , insulating shields and vary depth rotary handle Make - Legrand, Cat No. - 4220 07 /L&T /ABB

OUTGOINGS a) MCCB FP, 25 kA, 160 AMPS with thermal magnetic release, Ics = 100% Icu, Adjustable Over Load setting: 0.8 -1.0 x In, with spreader links , insulating shields and vary depth rotary handle Make - Legrand, Cat No. - 4200 57 /L&T /ABB

b) MCCB FP, 25 kA, 100 AMPS with thermal magnetic release, Ics = 100% Icu, Adjustable Over Load setting: 0.8 -1.0 x In, with spreader links , insulating shields and vary depth rotary handle Make - Legrand, Cat No. - 4200 55 /L&T /ABB

c) MCCB FP, 25 kA, 63 AMPS with thermal magnetic release, Ics = 100% Icu, Adjustable Over Load setting: 0.8 -1.0 x In, with spreader links , insulating shields and vary depth rotary handle Make - Legrand, Cat No. - 4200 53 /L&T /ABB

All as per Item No.02 above but suitable for and including following accessories :

INCOMER : MCCB FP, 25 kA, 250 AMPS with thermal magnetic release, Ics = 100% Icu, Adjustable Over Load setting: 0.8 -1.0 x In, with spreader links , insulating shields and vary depth rotary handle Make - Legrand, Cat No. - 4202 19 /L&T /ABB

OUTGOINGS a) MCCB FP, 25 kA, 100 AMPS with thermal magnetic release, Ics = 100% Icu, Adjustable Over Load setting: 0.8 -1.0 x In, with spreader links , insulating shields and vary depth rotary handle Make - Legrand, Cat No. - 4200 55 /L&T /ABB

b) MCCB FP, 25 kA, 63 AMPS with thermal magnetic release, Ics = 100% Icu, Adjustable Over Load setting: 0.8 -1.0 x In, with spreader links , insulating shields and vary depth rotary handle Make - Legrand, Cat No. - 4200 53 /L&T /ABB

c) MCB four pole 20 to 32 Amps, 415 volts, 10 kA breaking capacity, 'C' curve Make Legrand Ct No 4086 78-80 /L&T /ABB

All as per Item No.02 above but suitable for and including following accessories :

INCOMER : MCCB FP, 25 kA, 250 AMPS with thermal magnetic release, Ics = 100% Icu, Adjustable Over Load setting: 0.8 -1.0 x In, with spreader links , insulating shields and vary depth rotary handle Make - Legrand, Cat No. - 4202 19 /L&T /ABB

OUTGOINGS a) MCCB FP, 25 kA, 100 AMPS with thermal magnetic release, Ics = 100% Icu, Adjustable Over Load setting: 0.8 -1.0 x In, with spreader links , insulating shields and vary depth rotary handle Make - Legrand, Cat No. - 4200 55 /L&T /ABB

b) MCCB FP, 25 kA, 63 AMPS with thermal magnetic release, Ics = 100% Icu, Adjustable Over Load setting: 0.8 -1.0 x In, with spreader links , insulating shields and vary depth rotary handle Make - Legrand, Cat No. - 4200 53 /L&T /ABB

c) MCB four pole 20 to 32 Amps, 415 volts, 10 kA breaking capacity, 'C' curve Make Legrand Ct No 4086 78-80 /L&T /ABB

Removing of old ICTP main switch after disconecting the incoming and out going cables and supply and fix MCCB thermal magnetic release 4P 25 KA 160 Amps Make Legrand Cat No 4200 57 /L&T /ABB with one way metal inclosure Cat No 5078 01 /L&T /ABB and making conections of cables with suitable size nutbolt etc including making good the disturbed suface of wall including material complate all as specifide and directed.

Removing of old ICTP main switch after disconecting the incoming and out going cables and supply and fix MCCB thermal magnetic release 4P 25 KA 100 Amps Make Legrand Cat No 4200 55 /L&T /ABB with one way metal inclosure Cat No 5078 01 /L&T /ABB and making conections of cables with suitable size nutbolt etc including making good the disturbed suface of wall including material complate all as specifide and directed.

Removing of old ICTP main switch after disconecting the incoming and out going cables and supply and fix MCCB thermal magnetic release 4P 25 KA 63 Amps Make Legrand Cat No 4200 53 /L&T /ABB with one way metal inclosure Cat No 5078 01 /L&T /ABB and making conections of cables with suitable size nutbolt etc including making good the disturbed suface of wall including material complate all as specifide and directed.

Removing of old ICTP main switch after disconecting the incoming and out going cables and supply and fix MCB "C" curve TPN 10 KA 20 to 32 Amps Make Legrand Cat No 4086 78-80 /L&T/ C&S and one way metal inclosure Make Legrand Cat No 507793 /L&T/ C&S including making good the disturbed suface of wall including material complate all as specifide and directed.

Supply and fix aluminium tube terminal ( Lug/thimble) heavy duty suitable for XLPE conductor 10 sqmm size make Dowells / Comet

Supply and fix aluminium tube terminal ( Lug/thimble) heavy duty suitable for XLPE conductor 16 sqmm size make Dowells / Comet

Supply and fix aluminium tube terminal ( Lug/thimble) heavy duty suitable for XLPE conductor 25 sqmm size make Dowells / Comet

Supply and fix aluminium tube terminal ( Lug/thimble) heavy duty suitable for XLPE conductor 35 sqmm size make Dowells / Comet

Supply and fix aluminium tube terminal ( Lug/thimble) heavy duty suitable for XLPE conductor 50 sqmm size make Dowells / Comet

Supply and fix aluminium tube terminal ( Lug/thimble) heavy duty suitable for XLPE conductor 70 sqmm size make Dowells / Comet

Supply and fix aluminium tube terminal ( Lug/thimble) heavy duty suitable for XLPE conductor 95 sqmm size make Dowells / Comet

Supply and fix aluminium tube terminal ( Lug/thimble) heavy duty suitable for XLPE conductor 120sqmm size make Dowells / Comet

Supply and fix aluminium tube terminal ( Lug/thimble) heavy duty suitable for XLPE conductor 150 sqmm size make Dowells / Comet

Supply and fix y Copper tube terminal ( Lug/thimble) heavy duty suitable for XLPE conductor 10 sqmm size make Dowells / Comet

Supply and fix Copper tube terminal ( Lug/thimble) heavy duty suitable for XLPE conductor 16 sqmm size make Dowells / Comet

Supply and fix Copper tube terminal ( Lug/thimble) heavy duty suitable for XLPE conductor 25 sqmm size make Dowells / Comet

Supply and fix Copper tube terminal ( Lug/thimble) heavy duty suitable for XLPE conductor 35 sqmm size make Dowells / Comet

Supply and fix double compression weather froof brass cable glande suitable for armoured cables of 12 to 16.5 mm dia

Supply and fix double compression weather froof brass cable glande suitable for armoured cables of 16.5 to 18.5 mm dia

Supply and fix double compression weather froof brass cable glande suitable for armoured cables of 18.5 to 20 mm dia

Supply and fix double compression weather froof brass cable glande suitable for armoured cables of 20 to 23 mm dia

Supply and fix double compression weather froof brass cable glande suitable for armoured cables of 23 to 26 mm dia

Supply and fix double compression weather froof brass cable glande suitable for armoured cables of 26 to 30 mm dia

Supply and fix double compression weather froof brass cable glande suitable for armoured cables of 30 to 33 mm dia

Supply and fix double compression weather froof brass cable glande suitable for armoured cables of 33 to 37 mm dia

Supply and fix double compression weather froof brass cable glande suitable for armoured cables of 37 to 41 mm dia

M&L cross arms, bracing, supports, clamps and back plates fabricated from structual steel sections including nuts, bolts, washers, welding, bending cold or hot, drilling holes for bolts in any shape or size as indicted and inclusive of one primer coat one under coat and two finishing coat of oil paint.of colour approved by Engr-in-charge.

Om Construction

M/s Vijay Airconditioning Pvt Ltd

Techmat trading solution

M/S - KRUPA ELECTRICALS

AN-ICON Engineering Technologies And Infrastructure Developments Pvt. Ltd

Mahindra Electric Stores

Leo Enterprises

Adinath Technical Services

REKHA ELECTRICALS

Rajan Traders

Rama Electricals

CHAITANYA WINDWELL

T.H.ASSOCIATES

R. T. Saluji