SUPPLY AND INSTALLATION OF INVERTER BASED CASSETTES TYPE ACS & CONFERENEC FURNITURE AT AJMER PLANT

SUBJECT: SUPPLY AND INSTALLATION OF INVERTER BASED CASSETTES TYPE ACs & CONFERENEC

FURNITURE AT AJMER PLANT

S.No DESCRIPTIONS UNIT QTY RATE/UNIT GST 18%

(INR) (INR) (INR)

Supply, Installation, Nitrogen Testing and Commissioning of Cassette

AC complete in all respect of 2 Tonne Nominal Capacity Inverter

Cassette Air-Conditioners(Daikin/carrier/blue star/voltas ) having

1 twin Rotary compressor, Copper Condenser, low indoor noise level Nos.

having minimum 3 Star rating as per BEE.

Installation charges for 4 nos. of cassettes Acs including -

Refrigerant Piping, Supply, Installation & Commissioning of Soft

Copper 19 Gauge Refrigerant piping, complete with fittings, elbows,

supporting arrangement on walls/Ceilings & Soft Copper Piping for

cassette unit with insultation tape over and above the piping.

Drain Piping: Drain Water Piping work out of HDPE PVC pipes,

fittings, accessories, bend , elbows, angle support etc.

Framework: Supply Stand for outdoor units complete with pre-coated

M.S. Base Railing Stand etc.

Meeting/Conferenece table- 3 PAX MEETING TABLE 15X2.7X2.4 ft

Pre laminated Particle Board (PLB) 25 mm thickness. The edges are

covered with 2 mm thick PVC Edge band. E-1 –International Norms-E-

1 norms for Work tops Supported on MS powder coated Switch

Angular legs 40x40mm with MS powder coated cross beam 40x20.

18mm thick 450mm height PLT modesty panel is considered

machine pressed 2mm thick PVC lipping glued with hotmelt Eva glue

free from any VOC. 450mm Anodised flip up Made of Aluminium in

anodised finish, which has soft closure and three-way wire access &

PVC cable tray. Entry of cables from the floor into the cable tray, Wire

Entry covers are provided between the intermediate legs with

separator for entry of power and data. Power cables and Data cables

((CAT-6/7 cables). Technically, System efficiency is determined by

the volume of cables that the system can handle –basically the

dataCAT-6 cables. raceways are provided with covers-PLB/Metal

which can be easily removed for access -for maintenance servicing or

for fixing the switches sockets access to the switches and sockets

cables get terminated into the flip up box, flip up has flip cover which

Medium backed chairs Specifications: Twin Casters 50mm dia with

Nylon material complying to ANSI / BIFMA X 5.1 – 2017 standards.

The axle pin is rust protected- Zinc passivated. The pin is designed to

have push fit with lock ring. The 660mm PCD five pronged base is

made out of Nylon 30% GF Reinforced with bottom ribbing for

additional buttress and strength. Tested prudently and rigorously as

per ANSI/BIFMA X5.1-2017, General Purpose Office Chairs Standard.

The base Outer diameter shall be 750 mm with casters. MS ring is

insert moulded for better grip in the swaged taper. The Nylon base is

load tested as per the BIFMA standards- to 1134 Kg.Single swage

4 Class 4 tested -ANSI BIFMA performance standards. The pneumatic

height adjustment has an adjustment stroke of upto 100 mm as per

the seat height criteria and 360° revolving. Designed with possibility

to increase the seat height with Gas lift stroke 110-115 mm if

required. Self-Calibrate Mechanism Distinctively and

characteristically designed multi lock mechanism offering a very

smooth and fluidic reclining motion with automatic tension

adjustment feature. The mechanism offers seat to back recline ratio

of 3:7. The multi lock mechanism is fabricated from CR Sheets, with

CO2 welding process imparting uniform surface finish and tensile EA

Writing arm chairs-Specifications: Frame will be made out of ERW

tubes with 25 mm diameter with 2.1 mm thickness pipe conforming

to IS – 4923. Frame is welded by Co2 welding process for uniform

finish conforming to IS 816. Frame is offered with chrome finish with

thickness of 10-12 microns conforming to IS 1573. Frames are

durable & reduce the risk of scratches, chipping, abrasions, corrosion,

fading and other wear issues. Leg Bush: Molded with PPCP. The axle

pin is rust protected- Zinc passivated. The pin is designed to have

push fit with lock ring. Seat is duly upholstered with approved fabric

seat profile is designed with water fall to provide necessary comfort

in popliteal region. 100% polyester 185 GSM. Abrasion - >

5 cycles. Foam: Cushion with pre moulded foam of 50 - 55 kg/m3

density in the shape of plywood. Hardness – 22 to 28 kgf at 50%

deflection. Ply wood: 12 mm thick with 8 to 9 ply. It will be hot

pressed ply - conforming to I S 303. The plywood is fitted with metal

“T” nut to have metal to metal contact for the hardware used for

fixing the seat. Back outer is made of PAGF 15% moulded with

tonnage press. Back inner is made of PPCP. U shaped fixed arms

made of PPCP. It is fixed with PHS 8X25mm hardware. Writing desk

will be mounted on passivated rod measuring 16mm diameter and

100 mm length desk. High quality metal screws and tension fasteners

used conforming to Hardness 35-44 HRC. Back width: 480mm, Total

height: 885 mm, back height- 410 mm. Seat width: 480 mm, Seat

depth: 475 mm, Seat height: 475 mm. The chair should be fitted with

wheels for the movement. EA

Carpentary work and installation charges for panel boards in 9 pax

GROSS AMOUNT (1+2+3+4+5+6)