Loading
Loading…
Loading…
Tender Value
₹75.6 L
EMD Value
₹1.5 L
Closing Date
7 Aug 2026, 3:30 pmClosed
No
No
Single Packet System
Normal Tender
No
Not Applicable
Lowest to Highest
60 days
Expenditure
Capital (Works)
Above/Below/Par
TELECOM
14 conditions · 2 needing a document upload
The tenderer must have minimum average annual contractual turnover of V/N or 'V' whichever is less ; where V = Advertised value of the tender in crores of Rupees N = Number of years prescribed for completion of work for which bids have been invited. The average annual contractual turnover shall be calculated as an average of "total contractual payments" in the previous three financial years, as per the audited balance sheet. However, in case balance sheet of the previous year is yet to be prepared/ audited, the audited balance sheet of the fourth previous year shall be considered for calculating average annual contractual turnover. The tenderers shall submit requisite information as per Annexure- I, along with copies of Audited Balance Sheets duly certified by the Chartered Accountant/ Certificate from Chartered Accountant duly supported by Audited Balance Sheet.
The tenderer must have successfully completed or substantially completed any of the following during last 07 (seven) years, ending last day of month previous to the one in which tender is invited. : Three similar works each costing not less than the amount equal to 30% of advertised value of the tender, or Two similar works each costing not less than the amount equal to 40% of advertised value of the tender, or One similar work each costing not less than the amount equal to 60% of advertised value of the tender.
Defination of Similar Work :- 1. Supply & Installation of Master Slave Type LC gate communication system with/without voice logging facility. OR 2. AMC of Master Slave LC gate communication system with/without voice logging facility. NOTE A1: For the following equipment's a. SDH/STM/PDMUX/IPMPLS/VOIP b. Control equipment c. ISDN/IP based exchange d. CCTV/Video surveillance system e. Integrated security s y s t e m f. Networking equipment g. Train information display board/Coach guidance system/IPIS/GPS CLOCKS h. Secured communication system at level crossing gates i. VSAT j. MTRC 1. The equipment shall be procured from: a) If there is any RDSO approved source, then the equipment to be procured from the RDSO approved source or its authorized dealer/distributor. b) If there is no RDSO approved source but there is TEC approved source, then the equipment to be procured from the TEC approved source or its authorized dealer/ distributor. c) If there is no RDSO or TEC approved source then the equipment to be procured from the OEM or its authorized dealer/ distributor. 2. Make, Model Specification of the offered equipment along with OEM authorization if the tenderer is other than OEM shall be submitted along with the tender. 3. MOU with RDSO approved Source or TEC approved source or the OEM, covering Supply, installation, testing, commissioning of system including after sales support required during warranty period shall be submitted along with the tender.
26 conditions · 16 needing a document upload
Firm has to submit authorization letter for uploading documents on IREPS in case he/she is not an authorized person.
PAN card Copy should be enclosed.
Please submit the copy of the registration certificate as applicable, GSTIN certificate should be enclosed.
Please enter the percentage of local content in the material being offered. Please enter 0 for fully imported items, and 100 for fully indigenous items. The definition and calculation of local content shall be in accordance with the Make in India policy as incorporated in the tender conditions.
Contractors are allowed to make payments against this tender towards tender document cost and earnest money only through only payment modes available ON IREPS portal LIKE net banking, debit card, credit card etc.Manual payments through Demand draft, Banker cheque, Deposit receipts, FDR etc. are not allowed.
Copy of PAN number and GSTIN number should be submitted.
No post tender correspondence for submission of additional documents shall be entertained after opening of the Technical & Commercial offers. Even suo-moto post tender letters of the tenders shall be treated as NULL & Void.
(i)Tenderers will examine various provisions of the Central Goods and Service Tax Act, 2017(CGST)/Integrated Goods and Service Tax Act,2017(IGST)/Union Territory Goods and Service Tax Act,2017(UTGST)/respective states State Goods and Service Tax Act(SGST) also, as notified by Central/States Govt. and as amended from time to time and applicable taxes before bidding. Tenderers will ensure that full benefit of Input Tax Credit(ITC) likely to be availed by them is duly considered while quoting rates. (ii) The successful tenderer who is liable to be registered under CGST/IGST/UTGST/SGST Act shall submit GSTIN along with other details required under CGST/IGST/UTGST/SGST Act to railway immediately after the award of contract, without which no payment shall be released to the contractor. The contractor shall be responsible for deposition of applicable GST to the concerned authority. (iii) In case the successful tenderer is not liable to be registered under CGST/IGST/UTGST/SGST Act, the railway shall deduct the applicable GST from his/their bills under reverse charge mechanism(RCM) and deposit the same to the concerned authority.
Tenderer should go through Annexure 1 & 2 of Tender Notice (attached in Tender Document)for list of documents required to be uploaded along with the offer.
Implementation of VHF wireless communication system for Level Crossing Gate Last Mile Connectivity at ON-BQP Section of Lucknow Division, Northern Railway
106-Tele_Tender_18_26-27
106-Tele_Tender_18_26-27
Open
Works - General
180 Days
Lucknow, Uttar Pradesh
₹0
₹1.5 L
7 Aug 2026
17 Jul 2026
24 Jul 2026
33 items across 1 schedule
| # | Description | Unit | Qty | Rate | Amount |
|---|---|---|---|---|---|
| — | — | — | 75,62,828.48 | ||
| — | 9.00 | — | — | ||
| "Supply & Installation of Equipment in LC Gate using Wired & Wireless Data Communication as per RDSO Spec. no. RDSO/SPN/TC-49/2020 Ver 1.0 (Part-A) consisting of Control Equipment including Power Supply (12V / 15A DC) - Qty 01, SMF Battery (12V, 120AH) - Qty 01, 25W VHF Radio - Qty 01, Omni Directional Stacked Dipole Antenna Qty - 01, RG 217 Cable 25 Mtr, Self supported triangular Mast (12M Height) Qty 01. ( Warranty Period : Upto 30 months from the date of supply) INSPECTION: RDSO FOR SUPPLYPORTION""" | — | — | — | 43,60,773.78 | |
| — | 2.00 | — | — | ||
| "Supply & Installation of Equipment in ASM Room using Wired & Wireless Data Communication as per RDSO Spec. no. RDSO/SPN/TC-49/2020 Ver 1.0 (Part-A) consisting of: Control Equipment - with Voice Logging & (GSRP) including Power Supply (12V/15A DC) - Qty-01, SMF Battery (12V, 120AH) - Qty 01, 25W VHF Radio Qty 01, Omni Directional Stacked Dipole Antenna Qty 01, RG 217 Cable 35 Mtr, GI Pipe 10 Ft height for Antenna Mounting Qty 01. INSPECTION: RDSO FOR SUPPLYPORTION""" | — | — | — | 12,00,031.68 | |
| — | 11.00 | — | — | ||
| "Supply, Installation & commissioning of Maintenance free earth using basic earthing kit as per RDSO specification RDSO/SPN/197/2008 or latest and Drg No. SDO/RDSO/E&B /001 & 002 dated 19.9.2008 or latest. Earthing kit consist of 1. Earthing electrode of 17mm dia and 3 meter long-01 no. 2. MEEB (300mm X 25mm X 6MM) -01 no. 3. SEEB (150mm X 25mm X 6 mm) - 01 no. 4. Earth enhancing compound - 30 Kg (minimum). This include provision of earth connection from MEEB to S&T equipment i.e. cable sheath, apparatus case, IPS, data logger, signal etc. with PVC earth wire of size 16/25 Sq.mm through copper lugs of suitable size. PVC wire shall be supplied by Railways. Note: At certain locations it may not be possible to achieve earth resistance of less than 1.0 ohm with one earth electrode/pit due to soil resistivity. In such case provision of loop earth consisting of more than one earth pit shall be done. For interconnection of two earth pits copper tape of size 25X2 sq. mm shall be provided by contractor. The number of pits required shall be decided based upon the resistance achieved for the earth pit already installed. The procedure mentioned above for one earth pit shall be repeated for other earth pits. The other earth so installed for the purpose of loop earthing arrangement shall be counted as separate earth. Material to be procured through RDSO approved firm. Contractor have to submit check list duly signed by OEM after installation. INSPECTION: RDSO FOR SUPPLY PORTION""" | — | — | — | 2,63,370.47 | |
| — | 9.00 | — | — | ||
| "Supply and Installation of Solar Panel System for LC Gate a. 100W Solar Module Make: UTL/EXIDE/Liveguard or better. This includes - 10A/12/24 Solar charge Controller and other required accessories - 1 No. b. Mounting Structure With All Hardware Fittings & Solar DC Wire 2.5mm 8 Mtr. With MC4 Connector. - 1 Job All required accessories required for installation shall be supplied by contractor as per the instructions of site engineer. The Solar panel shall be compatible to Item no. 1 & 2 (RDSO Spec. no. RDSO/SPN/TC-49/2020 Ver 1.0 IRS:S 84/92 with Amd. 2 or latest) INSPECTION: CONSIGNEE FOR SUPPLY PORTION""" | — | — | — | 93,447.27 | |
| — | 5.00 | — | — | ||
| "Supply of Master Telephone Unit with voicelogging facility for Electronic LC GateTelephone System as per Specification No.RDSO /SPN/TC/51/2011 Rev 1.0 or latest. INSPECTION: RDSO " | — | — | — | 2,33,046.1 | |
| — | 30.00 | — | — | ||
| "Supply of Gate Telephone (Slave Telephones)for Electronic LC Gate Telephone System asper Specification No. RDSO/SPN/TC/51/2011 Rev 1.0 or latest. INSPECTION: RDSO " | — | — | — | 1,54,801.8 | |
| — | 10.00 | — | — | ||
| "Supply of Power Supply System with MF Battery of12V/24V DC (12V DC supply shall be connected tothe Station Telephone Unit & 24V shall be fed toLine Circuit) with maintenance free battery forelectronic LC gate telephone system as perSpecification No. RDSO/SPN/TC-51/2011, Rev 3.0Amd.1 or latest including battery charger. INSPECTION: CONSIGNEE " | — | — | — | 63,697.1 | |
| — | 50.00 | — | — | ||
| "Supply of 12V/120AHMaintenance Free Battery ofAmarRaja, HBL or Exide Make INSPECTION: RDSO " | — | — | — | 3,72,958.5 | |
| — | 3.00 | — | — | ||
| "Supply of SMPS based Battery Chargers as per RDSO Spec forTelecom use 48 volts, 25 Ampsin 2+1 configuration modulesof 25 Amps with ultimateexpandable capacity 50 Amps,automatic switching betweenthe modules as per RDSO SpecNo. RDSO/SPN/TC/23/1999version 4 or latest along withtwo potential free contacts for two sets of200AH Battery. It shall beequipped with surge andlightening protection of Class-B& C. INSPECTION: RDSO" | — | — | — | 3,56,067.9 | |
| — | 3.00 | — | — | ||
| Installation of Battery chargers, Power distribution Board along with MCBs of suitable ratings and wiring and commissioning of External alarm contacts through EMS. The work includes supply of battery rack, MCBs, battery cable and battery lugs and other accessories required for installation of power plant. | — | — | — | 8,700.45 | |
| — | 3.00 | — | — | ||
| "Supply of 48Volt/200AHmaintenance free VRLA Batteries duly charged as per IRS Spec. No. S-93/96(A) withamendments-1 or latest INSPECTION: RDSO " | — | — | — | 2,69,359.11 | |
| — | 2.00 | — | — | ||
| "Supply of Online UPS of Rating 1.0 KVA With Battery Of Backup Time 60 Minutes Brand: Uniline/APC/NUMAX or better INSPECTION: CONSIGNEE " | — | — | — | 54,280.8 | |
| — | 2.00 | — | — | ||
| "Tools Kit for maintenance with small sizecanvas bag with following items :- 1)Combination Plier 8"", 2) Long Nose Plier(Round Nose ) 6"" , 3) Wire Striper Plier6"" , 4) Screw Driver set ( 5 Piece) , 5)Hexa with frame 12"" 6) Double Open endD spanner set (6 to 32 mm) 7)Adjustable Spanner set 8"" 8) Ball pinHammer (200 gm) , 9) Side Cutting Plier6"" 10) Soldring iron (Soldron make orsimilar) 11) Torch cell LED (3 cell)(Eveready/ Geep or similar ), 12) KroneTool (Krone make or similar) , All ToolItem 1 to 9 of Taparia/Gedor/ Jhalanimake or similar. INSPECTION: CONSIGNEE " | — | — | — | 14,532.14 | |
| — | 2.00 | — | — | ||
| "Supply of Transmission measuring set as per IRS TC 43/87, make Aplab or better INSPECTION:CONSIGNEE" | — | — | — | 56,195.26 | |
| — | 1.00 | — | — | ||
| "Supply of Portable digital auto range multi-meter clamp type Philips, Motwani, Fluke or Rishabh make capable to measure from (0.1mv/0.01ma) AC/DC upto 50Amp(AC/DC), 600V(AC/DC) and 0.1 ohms- 40M ohms suitable for measurement of Freq., capacitance complete with Manual, leads, battery and holster etc. INSPECTION: CONSIGNEE " | — | — | — | 9,610.72 | |
| — | 10.00 | — | — | ||
| "Supply of 4G VoLTE fixed wireless phone as per attached specification. Make Beetel, Model F-3 4G or better INSPECTION:CONSIGNEE" | — | — | — | 51,955.4 |
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
HTML
nit.pdf
NIT
ACSGCC22-231to6.pdf
ATTACHMENT
GCC Correction slip 7 to 10
ATTACHMENT
TD-18VHFON-BQP.pdf
ATTACHMENT
GCC_April-2022_1.pdf
ATTACHMENT
GCCACS11_compressed.pdf
ATTACHMENT
GCCAdvanceCorrectionSlipno7-10.pdf
ATTACHMENT
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .